Alfa IN aXe 250 PULSE Smart (AL), aXe 320 PULSE Smart (AL), aXe 250 Smart, aXe 320 Smart Instruction Manual

Download

ALFA IN a.s. © www.alfain.eu

aXe 250-320 PULSE smart (AL) manual EN 04

WELDING MACHINES

aXe 250 PULSE

Smart

(AL)

GAS

aXe 320 PULSE

Smart

(AL)

GAS / H2O

aXe 250

Smart

GAS

aXe 320

Smart

GAS / H2O

INSTRUCTION MANUAL

2/31

ALFA IN a.s. © www.alfain.eu

CONTENT

1. INTRODUCTION ...................................................................................................3

2. SAFETY PRECAUTIONS .........................................................................................4

3. OPERATING CONDITIONS .....................................................................................5

4. TECHNICAL DATA .................................................................................................6

5. ACCESSORIES .......................................................................................................8

6. DESCRIPTION OF THE APPLIANCE .........................................................................9

7. BASIC SETTINGS ................................................................................................. 17

8. MIG/MAG WELDING SYNERGY .......................................................................... 24

9. PULSED MODE ................................................................................................... 25

10. MIG/MAG WELDING MANUAL ........................................................................... 26

11. MMA WELDING (COATED ELECTRODE- ELE) ....................................................... 27

12. ROUTINE MAINTENANCE & INSPECTION ............................................................ 28

13. DISPOSAL ........................................................................................................... 31

3/31

ALFA IN a.s. © www.alfain.eu

1. INTRODUCTION

Dear Consumers! Company ALFA IN a.s. thanks you for buying our product and believe that you

will be satisfied with our machine. Welding machines aXe 250 PULSE smart (AL) GAS and aXe 320 PULSE

smart (AL) GAS/H2O are IGBT invertors. They are designed for welding method MMA, MIG (Metal Inert gas) and MAG (Metal Active Gas). This is welding in protective atmosphere (methods MIG, MAG). We are using inert (impassive) and active gases during welding. These methods are very productive and particularly suitable for the connections of structural steels.

With welding machines aXe 250 PULSE smart (AL) GAS and aXe 320 PULSE smart (AL) GAS/H2O it is possible to weld different types of connections (blunt, single-sided, double-sided, fillet, lap etc.) using wire diameter from 0,6 – 0,8 mm, or 1,0 – 1,2 mm of different metals and alloys (carbon and alloy steels, aluminum alloys etc.).

Welding machines aXe 250 smart GAS and aXe 320 smart GAS/H2O haven’t pulsed mode. But it is possible to extend these machines about pulsed mode.

The machines can be used for welding in areas with increased

danger of electric shock. Machines comply with the relevant requirements for CE marking.

We reserve the law of adjustments and changes in case of printing errors, change of technical paramaters, accessories etc. without previous notice. These changes may not be reflected in the manuals for use in paper or electronic form.

4/31

ALFA IN a.s. © www.alfain.eu

2. SAFETY PRECAUTIONS

PERSONAL PROTECTION

1. For safety reasons, it is necessary to use welding gloves during welding. These gloves will protect you before intervention of electric current (open circuit voltage). It protects you against thermal radiation and splashing drops of hot metal too. Wear sturdy isolated shoes. Do not wear open shoes, because drops of hot metal can cause burns.

2. Do not look into the welding arc without eye and face protection. Always use good quality welding helmet with intact protective filter.

3. The persons appearing in the vicinity of the welding must be informed of the danger and must be equipped with protective equipment.

4. During welding, especially in small spaces, it is necessary to ensure an adequate supply of fresh air, because during welding, harmful fumes arise.

5. In tanks of gas, oil, fuel, etc., (even empty ones) do not make welding, because there is a chance of explosion.

6. In areas with chance of explosion special provisions are applied.

7. Welding machines that are subjected to great exertion must comply with specific security requirements. These include the rail pressure of the vessel etc. These connections may only be carried out by competently trained welders with the necessary permissions.

SAFETY REGULATIONS

1. Before starting work with welding machine it is necessary to get familiar with the provisions of the ČSN 050601 and norm ČSN 050630.

2. With a bottle of CO2 or mixed gases should be handled according to the regulations for working with pressure vessels contained in ČSN 07 83 05 and norm ČSN 07 85 09.

3. The welder must use protective equipment.

4. Before working on the electrical part, removing the cover or cleaning it is necessary to disconnect the device from the network.

5/31

ALFA IN a.s. © www.alfain.eu

3. OPERATING CONDITIONS

1. Putting the machine into operation can be performed only by trained personnel and only within the technical provisions. The manufacturer is not liable for damages resulting from improper use or handling. For maintenance and repair, use only original spare parts from ALFA IN.

2. Device complies with IEC 61000-3-12 with following conditions: Short-circuit power Ssc of network in place at an interface between the user's supply and the public network (PCC) must be least 4106 kW. User is obliged to consult with the electricity supplier if the impedance of the network at this point is that required short-circuit capacity Z

max

= 36 mΩ and whether the device can be connected with a public low-voltage network.

On the nameplate are the following symbols: .

3. The welding machine is tested according to the degree of protection IP 23S, which provides protection against the intrusion of solid bodies with a diameter greater than 12 mm and protection against ingress of water, falling on the machine in a vertical direction or max degree of 60°.

4. The machine must be positioned so that cooling air can enter and leave through cooling vents with no problem. It is necessary to ensure that there are no mechanical equipment, especially metal particles (e.g. during grinding) drawn into the machine.

5. Handling handle is intended for movement, it is not designed to lifting the machine.

6. In case of overheating of the machine welding is automatically stopped and this condition is signalized by pilot light.

7. All interventions in the el. equipment as well as repair (removal of the plug, fuse replacement) should be performed by an authorized person.

8. With competent mains voltage and input must match the plug.

9. Do not use the machine for other purposes, such as defrosting pipes, starter source, etc.

10. It is necessary for welding machine to undergo a periodic inspection every 6/12 months by an authorized officer according to ČSN 331500 and ČSN 050630 – see Maintenance and service tests.

11. The welding machine is designed especially for industrial areas. In case of using it in other areas there may exist special measures (see EN 60974-10).

12. It is necessary to protect the machine against:

a. Moisture and rain b. Mechanical damage c. Draft and possibly ventilation of neighboring machines d. Excessive overloading – exceeding tech. parameters e. Rough treatment f. Chemically aggressive environments

6/31

ALFA IN a.s. © www.alfain.eu

ELECTROMAGNETIC COMPATIBILITY

The welding device is in terms of interference designed primarily for industrial areas. It meets the requirements of EN 60974-10 class A and it isn’t designed for using in residential areas, where the electrical energy is supplied by public low-voltage power supply network. It can be here potential problems with ensuring of electromagnetic compatibility in this areas, due to interference caused by power lines as well as the radiated interference.

During operation, the device may be the source of interference.



Caution



We warn users, that they are responsible for possible interference from welding.

4. TECHNICAL DATA

Model

aXe 250 PULSE smart (AL) GAS

Method MIG/MAG MMA Mains voltage V/Hz 3x400/50-60 Welding current range A 20 - 250 10 - 250 Open-circuit voltage U20 V 63,1 Mains protection A 16 @ Max. effective current I

1eff

A 12,9 13,0 Welding current (DZ=100%) I2 A 210 190 Welding current (DZ=60%) I2 A 250 230 Welding current (DZ=x%) I2 A 60%=250 50%=250 Protection IP 23S Standards EN 60974-1, EN 60974-10 cl. A Dimensions (w x l x h) generator mm 474 x 911 x 670 Weight - generator /compact kg 47,6 Wire speed m/min 1,0 - 20,0 --Spool diameter mm 300 --Spool weight kg 18 ---

7/31

ALFA IN a.s. © www.alfain.eu

Model

aXe 320 PULSE

smart

(AL)

H2O

aXe 320 PULSE

smart

(AL)

GAS

Method MIG/MAG

MMA MIG/MAG MMA

Mains voltage V/Hz

3 x 400/50-60 3 x 400/50-60

Welding current range A 20 - 315

10 - 300 20 - 315 10 - 300 Open-circuit voltage U20 V 63,1 63,1 Mains protection A 16 @ 16 @ Max. effective current I

1eff

A 13,3 12,8 12,9 12,8 Welding current (DZ=100%) I2 A 210 190 210 190 Welding current (DZ=60%) I2 A 250 230 250 230 Welding current (DZ=x%) I2 A 25%=315 20%=300 25%=315 20%=300 Protection IP 23S Standards EN 60974-1; EN 60974-10 cl. A Dimensions (w x l x h) generator mm 474 x 902 x 884 474 x 911 x 670 Weight - generator /compact kg 72,5 47,6 Wire speed m/min 1,0 - 20,0 --- 1,0 - 20,0 --Spool diameter mm 300 --- 300 --Spool weight kg 18 ---

18 ---

Cooling power (Q=1l/min) kW 0,74 ---

--- ---

Total liquid content l 4,0 ---

--- ---

Max. pressure Bar 3,5 ---

---

Max. flow l/min 8,0 ---

--- ---

The machine marked with this symbol can be used for welding in areas with an increased risk of electric shock. The machine structure is designed so that, in any case, even if the failure rectifier does not exceed the permitted peak value of the open circuit voltage according to EN 60974-1, i.e., 113 V direct current or 68 V alternating.

8/31

ALFA IN a.s. © www.alfain.eu

5. ACCESSORIES

PART OF DELIVERY

1. Roll (rolls) for wire with diameters 0,8 – 1,0 mm

2. Instruction manual

3. Reducing for the spool wire 5 kg and 15 kg

4. Earthing cable 3 m with clamp

5. Hose for gas connection

ACCESSORIES ON REQUEST

1. Pressure regulator

2. Spare parts for torch

3. Rolls 0,6-0,8 and 1,0-1,2 with different grooves

4. Torch PARKER SGA-LW305A Ultralight 3 m – 5 m

5. Torch PARKER DIGIMIG 305 aXe IN UD Ultralight 3 m – 5 m

6. Torch PARKER SGB 240W délka 3 m – 5 m

7. Torch PARKER DIGIMIG 240W aXe IN UD 3 m – 5 m

8. Set for aluminium welding

9. Wire cleaner



NOTICE



If you decide to use a different torch than the above, it is

necessary to choose one, according to your current range and load time of the torch. ALFA IN a.s. is not liable for damage caused by overload welding torches.

9/31

ALFA IN a.s. © www.alfain.eu

6. DESCRIPTION OF THE APPLIANCE

MAIN PARTS

Fig. 1 – Main parts of the machine

10/31

ALFA IN a.s. © www.alfain.eu

Fig. 2 – Main parts of the machine with cooling unit

11/31

ALFA IN a.s. © www.alfain.eu

Pos.

Description

A1 ON/OFF switch

A2 PCB

control panel

A3 Quic

k connector

(+)

A4 Quick connector (-)

A5 EURO

connector

A6 Wire feeder

A7 Spool holder

A8 Soneloid valve

A9 Mains cable

A10

Cooling unit

A11

Remote control connector for MMA method

A12

LED

A13

Button of inserting the wire

B1 EURO

connector

B2 EURO

connector male

B3 Torch

C1 Quick connector male

C2 Earthing clamps

C3 Quick connector

(+)

C4 Quick connector

(-)

F1 Gas bottle

F2 Cylinder Valve

F3 Pressure reducer

F4 High

ressure

anometer

F5 Low

ressure

anometer

F6 Adjusting Screw

F7 Gas outlet

F8 Soneloid valve

F9 Chain



NOTICE



If the machine is equipped with the connector A11, the machine can be controlled in MMA method by the remote control.

12/31

ALFA IN a.s. © www.alfain.eu

WIRE FEEDER

Fig. 3 - Wire feeder 4 rolls

Pos.

Description

E1 Nut of pressur

e arm

E2 Pressure arm

E3 I

nlet liner

E4 EURO connector

E5 Roll

CHOOSING THE FEEDING ROLL

In all machines ALFA IN MIG / MAG rolls with two grooves are used. These grooves are intended for two different wire diameters (e.g. 0,8 and 1,0 mm).

Rolls for wire feed must comply with the diameter and material of the welding wire. Only this way a smooth wire feed can be achieved. Irregularities of the wire feed leads to a poor quality of welding and deformation of the wire.







Fig. 4 - The influence of the roll groove on the welding wire

A Correct

B Wrong

C Wrong

13/31

ALFA IN a.s. © www.alfain.eu

OVERVIEW OF ROLLS FOR WIRE FEED

4 rolls

a =

19 mm

b = 3

7 mm

Groove type

Wire diameter

Item No

Steel

0,6-0,8 4299

0,8-1,0 4300

1,0-1,2 4301

1,2-1,6 4302

Aluminum

1,0-1,2 4306

1,2-1,6 4307

1,6-2,0 4308

2,4-3,2 4309

Flux core

1,0-1,2 4303

1,2-1,6 4304

2,4-3,2 4305

ADJUSTING THE MACHINE FOR ANOTHER WIRE DIAMETER

In all machines ALFA IN MIG / MAG are used rolls with two grooves. These grooves are intended for two different wire diameters (e.g. 0,8 a 1,0 mm). Groove can be replaced by removing the rolls and rotating them, or use a different roll grooves with required dimensions.

1. Open the nut E1 to the forward, pressure rolls E2 will be opened upward.

2. Unscrew the locking element and remove the roll.

3. If there is a suitable groove on the roll, rotate the roll and place it back on the shaft and secure it by screwing the element.

ADJUSTING THE MACHINE FOR WELDING OF ALUMINIUM

For feeding the AL wire it is necessary to use roll with the “U” profile - see paragraph

14/31

ALFA IN a.s. © www.alfain.eu

OVERVIEW OF ROLLS FOR WIRE FEED. To prevent problems with feeding use wires with diameter 1,0 mm of AIMg3 or AlMg. Wire of alloy Al99, 5 or AlSi5 are too soft and easily will cause problems with movement.

For the aluminum welding it is also necessary to provide the torch tefl. liner and special current nipple. We do not recommend you to use the torch longer than 3 m. Great attention must be paid to adjust the contact power of rolls – it must not be too high, otherwise there is a deformation of the wire.

As a protective atmosphere is necessary to use argon.

Fig. 5 – Customization of the feed for the aluminium wire

Pos. Description

G1 EURO

connector

G2 Roll

G3 Liner terminal for 4,0mm, 4,7mm outer diameter

G4 O-ri

ng 3,5 x1, 5mm to prevent escape of gas

G5 Nut

G6 Liner tefl.

G7 Sustain pipe

for teflon and plastic liner

INSERTING THE WIRE

1. Open the side cover of the wire feeder space.

2. Put the wire spool on the wire spool holder D1 and fix it with the fixing nut D2. If a spool (size of 15 or 18 kg) is used, put on each side of the spool adapter D3. The hole in the back of the adapter must fit into the pin on the wire spool holder!

3. Cut off the curved or damaged end of welding wire and lead it through the inlet liner E3, and the roll into the liner inside the EURO torch connector (about 5 cm). Make sure, that you use the suitable groove.

4. Put the pressure arm E2 down in that way, that the teeth or the gear fit and fix it by setting the lever E1 into vertical position.

5. Adjust the pressure nut that way that it provides constant movement of wire but it does not deform wire. By pressing the button A13, placed in the space of the wire feeder, turn on the motor of the feeder. The adjusting screw is located under the plastic screws E1.

6. The spool brake is set by the manufacturer. If necessary, the brake can be adjusted by a screw D1 so that while stopping the feed, spool will be stopped on time (it will avoid excessive release of wire). However, too tight brake needlessly strains the feeding mechanism and thus slippage

15/31

ALFA IN a.s. © www.alfain.eu

may occur in the wire rolls.

Fig. 6 - Spool holder

ADJUSTING PRESSURE FORCE OF FEED ROLLS

Important thing for reliable operation of the feeding mechanism is the size of pressure force of feed rolls.

The amount of force depends on the type of welding wire, for aluminum or tube wire, we choose a smaller pressure force.

If the pressure force is too small, slippage may occur and thus irregular wire feeding speed.

If the pressure force is too high, it will lead to increased mechanical wear of bearings and it can damage the machine. Before putting into operation, clean the rolls from preservative oil.

INSERTING THE WIRE TO THE TORCH AND CONNECTION OF EARTH CABLE

1. Connect the earthling clamps to the welder or to the welding table.

2. Notice When inserting the wire do not point with torch to the eyes!

3. Screw the central end of the torch B2 to connector B1 on the machine while the machine is turned off.

4. Remove the gas nozzle from the torch.

5. Unscrew the current nozzle.

6. Connect the machine to power supply.

7. Turn the ON/OFF switch to ON.

8. Press button A13 in the space of wire feeder to run the motor of the feeder. The welding wire is fed into the torch. After coming off from the torch tube, screw the current nozzle and gas nozzle on.

9. Before welding, spray the area in a gas hose and current nozzle with a separation spray, to prevent damage.

Pos. Description

D1 Spool Holder

D2 Nut Spool Holder

D3 Adapter

16/31

ALFA IN a.s. © www.alfain.eu

ADJUSTMENT OF GAS FLOW

The electric arc and the weld must be perfectly shielded by gas. Too small amount of gas does not perform the protective atmosphere and on the other hand to big amount of the gas brings air into the electric arc.



Notice



Gas bottle must be well secured against fall. This manual does

not solve the safe securing of gas bottle. Information can be obtained from a supplier of industrial gases.

1. Fit the gas hose to the outlet on the back panel of the machine.

2. Press button V1 (pic. 8) on the main panel to the switching of the gas valve. If you hold the button for less than 3 s, after releasing the button, the gas valve will turn off. If you hold the button for more than 3 s, it will turn off the gas valve after about 20 s, or after pressing any button.

3. Turn the adjusting screw F7 at the bottom side pressure reducing valve, until the meter F6 shows the required flow, then release the button. The optimum flow is 10-15l/min.

4. After long-term shutdown of the machine or replacement of the torch it is suitable to blow the pipes with protective gas before welding.

Fig. 2 – Gas flow setting

Pos.

Description

F1 Gas b

ottle

F2 Cylinder Valve

F4 Pressure Reducer

F5 High Pressure Manometer

F6 Low Pressure Manometer

F7 Adjusting Screw

F8 Gas outlet

17/31

ALFA IN a.s. © www.alfain.eu

7. BASIC SETTINGS

CONTROL PANEL

Fig. 8 – Control panel

Pos.

Description

Button

: Gas

test

V2 Button:

ulsed mode

V3 LED

- If it illuminates

, when Pulsed mode was chosen

V4 Instant JOB buttons 1-6

V5 Current encoder

V6 LED

- Material thickness (mm)

V7 LED - Wire speed (m/min)

V8 Button for selecting

the parameters to be displayed

V9 LED

- Current (A)

V10

Left display shows:

1. Welding current

2. Welding current in the MMA mode

3. Speed of the wire

4. Material thickness

5. Sign

the

secondary parameter

V11

Right display shows:

1. Welding voltage

2. Correction

3. Choke

V12

LED

- V

oltage or

oltage

orrection

V13

Button for selecting the parameters to be displayed

18/31

ALFA IN a.s. © www.alfain.eu

V14

LED

- Wire

peed

orrection

V15

LED

- Choke or

hoke

orrection

V16

Encoder

oltage or

orrection

V17

LED

- T

wo stroke

– 2T

V18

LED

- F

our stroke

– 4T

V19

Button for selecting the parameters to be displayed

SETTING THE METHOD OF WELDING

1. By long-pressing the encoder V5 open the menu.

2. By turning the encoder V5 choose the method ELE (covered electrode MMA), MAN (MIG/MAG manual) or SYN (MIG/MAG synergistic). Confirm your choice by pressing the button V5.

WELDING METHOD SYNERGY

Synergic curves are welded in PB position (fillet connection, horizontal, obliquely from above). It is necessary to perform the parameters correction for welding in other positions.

AXE 250-320 PULSE SMART (AL) ø 0.8 ø 1.0 ø 1.2

SG/Fe Ar 82 % CO2 18 % 0 * 1 * 2 * SG/Fe Ar 92 % CO2 8 % 3 * 4 * 5 *

SG/Fe CO2 100 % 6 7 8 Cr/Ni 308 Ar 97,5 % CO2 2,5 % 9 * 10 * 11 * Cr/Ni 316 Ar 97,5 % CO2 2,5 % 12 * 13 * 14 *

AlMg Ar 100 % x 15 ** 16 **

AlSi Ar 100 % x 17 ** 18 **

Table of synergic parameters * You can switch on/off the pulsed mode by means of the button V2. ** Can be welded only in the pulsed mode, and it is available only for AL

variant of the machine.

1. Left display V10 shows SYN, right display V11 shows the number of

synergistic curve.

2. Selects the synergic curve (program number) using the encoder V16

according to the table, which is located inside. To confirm the program number press the encoder V5.

3. If you press any button other than V5, or after 10 s, you exit the menu.

19/31

ALFA IN a.s. © www.alfain.eu

CALIBRATION OF THE WELDING CIRCUIT

Welding features of the synergic curve depends on many factors, for example: on the torch length, ground cable length, qrounding quality, weldment distance from the grounding place etc. Therefore, it is appropriate to perform the calibration of the welding circuit for actual welding conditions.

1. Simultaneously press V20 and V5 encoder and you will enter the menu

for secondary parameters.

2. Choose CAL parameter by the encoder V5 and press it to confirm.

3. Set CrE by the encoder V5 and press it to confirm.

4. Unscrew the gas nozzle of the welding torch.

5. Cut off the welding wire tightly at the welding jet.

6. Piece of the welding wire (about 50 mm) give to the wire feeder. In the current jet cannot be now any welding wire.

7. Place the welding tip of welding torch on a clean or cleaned place of the workpiece by the gentle pressure, press and hold the torch button for 2 s. For a moment flows the short-circuit current. Short-circuit current helps to determine and screen the new resistence. (Value can be from 0 mΩ to 60 mΩ – for users aren’t these values important, factory reset CrE = 10 mΩ, you can set this value by the encoder V16).

8. Right display V11 shows Err, if an error occurs. You must repeat the measurement.

9. Screw back the gas nozzle of the welding torch.

10. Insert the welding wire.

QUICK SETTING THE JOB - MEMORY

Works for all welding methods.

1. Long press (4s) one of the buttons V4 (1,2,3,4,5,6) to save set parameters to memory.

2. Short press one of the buttons V4 (1,2,3,4,5,6) to load parameters from memory.

3. Display shows no Job, if at the desired position isn’t saved any JOB.

WELDING MODE 2T – TWO STROKE

Works for both welding methods MIG/MAG.

Press the button V20 to switch between the modes 2T , 4T and

. The two stroke mode is signalized by LED V17. First tact: press and

hold the torch button, the machine will start welding. Second tact: release the torch button, the machine will stop welding.

20/31

ALFA IN a.s. © www.alfain.eu

WELDING MODE 4T – FOUR STROKE

Works for both welding methods MIG/MAG.

Press the button V20 to switch between the modes 2T , 4T and

. The four stroke mode is signalized by LED V18. First tact: press and

hold the torch button, the machine will start welding. Second tact: release the torch button, the machine will continue welding. Third tact: press the torch button, the machine will continue welding. Fourth tact: release the torch button, the machine will stop welding.

WELDING MODE 2T – TWO STROKE STAIRS

Works for both welding methods MIG/MAG.

Press the button V20 to switch between the modes 2T , 4T and

. The two stroke stairs mode is signalized by LEDs V17 and V19.

First tact: press and hold the torch button, the machine will start welding with the Start current SCu during the time START t S. Then after the time UP tuP start the machine welding with the main welding current (100 %). Second tact: release the torch button, after the time DOWN tdo start the machine welding with the End current ECu during the time END t E. After this time the machine will stop welding.

WELDING MODE 4T – FOUR STROKE STAIRS

Works for both welding methods MIG/MAG.

Press the button V20 to switch between the modes 2T , 4T and

. The four stroke mode is signalized by LEDs V18 and V19.

First tact: press and hold the torch button, the machine will start welding with the Start current SCu. Second tact: release the torch button, after the time UP tuP start the machine welding with the main welding current (100 %). Third tact: press the torch button, after the time DOWN tdo start the machine welding with the End current ECu. Fourth tact: release the torch button, the machine will stop welding.

BILEVEL BCU ≠ 100 %

The difference of BILEVEL compared with classical stairs is in the second tact. When you quickly press and release the torch button, the machine switches

between two set main welding currents.

21/31

ALFA IN a.s. © www.alfain.eu

Fig. 9 – Curves of modes

SECONDARY PARAMETERS MENU

From start the welding machine is set to factory settings (default). For most of the work it is not appropriate to change the secondary parameters. Secondary parameters for manual and synergistic methods are identical.

1. Simultaneously pressing V20 and V5 encoder enters the menu for secondary parameters.

2. Encoder A5 selects a parameter (ISP, PRG, PoG, brn), V16 encoder sets the desired value.

3. Press the encoder V5 to confirm the change.

4. Press any button, or after 10 s, to exit the menu without saving changes.

5. Secondary parameters are common for methods manual and synergy. Synergy method allows to set more secondary parameters.

22/31

ALFA IN a.s. © www.alfain.eu

Symbol

Meaning

Range (Default)

Mark

ISP (Initial speed) Approaching speed 10 - 100 % (30 %)

PrG

(Pre gas time)

Pre gas

0 - 20 s (0

,1 s)

PoG

(Post gas time)

Post gas

0 - 20 s (0,5 s)

brn (Burn back) Burn back 0 - 75 ms (50 ms)

SCu

(Start current)

Start current

10 -

200 % (130 %)

2, 4

bCu (Bilevel current) Second current

10 - 200 % (100 %

= turned off)

2, 4

ECu (End current) End current 10 - 200 % (70 %) 2, 4

tuP

(Time UP)

Time up

0,1

- 10,0 s (0,1 s)

2, 4

tdo

(Time DOWN)

Time down

0,1

- 10,0 s (0,1 s)

2, 4

t S (Time START) Time of start current 0,1 - 10,0 s (0,1 s) 2

t E (Time END)

Time of

end

current

0,1

- 10,0 s (0,1 s)

CAL (Calibration menu) Calibration menu

x.xx (version sw

PCB engine)

(*)

The last menu item is CAL – it is used to enter the calibration menu, which is intended only for authorized service.

Parameters marked as 2 are available only in 2T stairs mode. Parameters marked as 4 are available only in 4T stairs mode.

WELDING HOURS COUNTER

If you enter to secondary parameters menu, you can always display this value. By long-pressing the button V4 (1) will be displayed the welding time in hours.

CALIBRATION MENU

u-l

Calibration of voltage and current (password protected -

intended for authorized service

)

Cu Cooling unit oFF/on/Aut

Cor

Zeroing of the correction (YES = zeroing of the correction when is changed the output value in the synergic mode)

CrE

See

ALIBRATION

OF THE WELDING CIRCUIT

By long-pressing the button V4 (1) perform the display test. By long-pressing the button V4 (2) display the machine variant / roll size (only

for machines with speed measurement) (37 – AXE 250/320 PULSE SMART, 30 – AXE 250/320 PULSE MOBIL).

23/31

ALFA IN a.s. © www.alfain.eu

REMOTE CONTROL

Fig. 10 – Remote control from the torch

Pos. Description

H1 Display of remote control

H2 Display

Torch button M for choosing the function MAN: Wire speed, Voltage/Choke, JOB (See How to switch on the remote control of JOBs on below)

SYN: Power, Correction/Choke, JOB

Torch button LOCK lock/unlock the buttons UP/DOWN and M The UP/DOWN and M buttons get automatically locked when the torch trigger is pressed.

When the LED is on it indicates UP/DOWN and M button are

functioning.

H6 Torch button

H7 Torch button

DOWN

HOW TO SWITCH ON THE REMOTE CONTROL OF JOBS

1. By long-pressing buttons V13 and V20, at the same time, activate the JOB choice by the remote control. Display shows JOB on.

2. By means of the button H3 set the function JOB change.

3. By means of buttons H6 (UP) and H7 (DOWN) switch among the saved JOBs.

4. By short-pressing buttons V13 and V20, at the same time, deactivate the JOB choice the by remote control. Display shows JOB off.

24/31

Symbols on the torch display H1

Symbol Description

A synergic program is running on the welding machine

Amperage setting (SYN)

Wire speed setting

No symbol

Material thickness setting (SYN) Voltage setting (MAN)

Correction (SYN)

Symbols on the torch display H2

J.xx

JOBs (xx – JOB No)

I.xx

Choke level (SYN/MAN). (Only with firmware 2015 and newer)

ELE

Machine is in MMA (Electrode) mode

RESET

1. Pressing V8 and V20 at the same time more than 3 s makes RESET – default parameters will be restored.

2. It will delete saved JOBs!

COOLING UNIT TEST

1. Pressing V1 and V20 at the same time more than 3 s makes activation of the cooling unit.

2. If you press any button, test will end.

8. MIG/MAG WELDING SYNERGY

1. Choose SYN method (see SETTING THE METHOD OF WELDING).

2. Left display V10 shows machine output (current, wire feed speed, material thickness), right display V11 shows voltage value. Correction value (voltage, wire feed speed) or choke value is shown on the display V11 only during the start process.

3. Press the button V8 to switch setting and view of machine output (current, wire feed speed, material thickness).

4. Machine output (current, wire feed speed, material thickness) set by the encoder V5.

25/31

5. In the calibration menu you can set the choice of turning off correction zeroing at the change of the machine output value.

6. By long-pressing the button V13 switch between voltage correction and wire feed speed. By short-pressing this button switch between set correction and choke value.

7. Set the voltage correction, wire feed speed or choke value by the encoder V16 (if necessary).

8. Press the button V20 to switch between modes 2T/4T/2T stairs/4T stairs.

9. In the mode 2T stairs/4T stairs you cannot set the parameters during the welding process.

10. If is connected the torch with remote control, on its display is shown machine output (current, fire feed speed, material thickness), correction (voltage, wire feed speed) or choke value. With buttons H6 (UP) and H7 (DOWN) set the displayed value, with the button MODE switch between functions. If is activated the JOB choice by the remote control, you can switch between JOBs.

9. PULSED MODE

(does not apply to aXe 250 smart GAS and aXe 320 smart GAS/H2O)

1. With the button V2 switch on the pulsed mode (only at stated synergic programs).

2. If is the pulsed mode switched on, LED V3 at the button V2 shines.

3. Left display V10 shows machine output (current, wire feed speed, material thickness), right display V11 shows voltage value. Correction value (voltage, wire feed speed) is displayed on the dispay V11 only when you setting.

4. By pressing the button V8 can change the machine output screening (current, wire feed speed, material thickness).

5. Set the machine output (current, wire feed speed, material thickness) by the encoder V5.

6. In the calibration menu you can set the choice of turning off correction zeroing at the change of the machine output value.

7. By long-pressing the button V13 switch voltage correction and wire feed speed.

8. Set the voltage correction or wire feed speed by the encoder V16 (if necessary).

9. Press the button V20 to switch between modes 2T/4T/2T stairs/4T stairs.

26/31

10. If is connected the torch with remote control, on its display is shown machine output (current, fire feed speed, material thickness), correction (voltage, wire feed speed). With buttons H6 (UP) and H7 (DOWN) set the displayed value, with the button MODE switch between functions. If is activated the JOB choice by the remote control, you can switch between JOBs.

10. MIG/MAG WELDING MANUAL

1. Choose MAN method (see SETTING THE METHOD OF WELDING).

2. Left display V10 shows MAN.

3. Left display V10 shows wire feed speed, right display V11 shows voltage or choke.

4. Wire feed speed set by the encoder V5.

5. Voltage or choke set by the encoder V16.

6. By long-pressing the button V13 switch settings and screening of voltage or choke.

7. Press the button V20 to switch between modes 2T/4T.

8. During welding, the left display V10 shows measured values of welding current and the right display V11 shows voltage.

9. After welding, on the displays will remain measured values (HOLD) for 6 s.

10. If is connected the torch with remote control, on its display is shown wire feed speed, voltage or choke. With buttons H6 (UP) and H7 (DOWN) set the displayed value, with the button MODE swith between functions. If is activated the JOB choice by the remote control, you can switch between JOBs.

WELDING VOLTAGE It is set using voltage encoder V16.

WELDING CURRENT – GENERAL INFORMATION

Size of the welding current depends on the wire feed speed and voltage. Characteristic of the curve ("hardness / softness") can be controlled by correction of the choke.

Approximate setting for the MIG / MAG welding current and voltage corresponds the empirical relationship U2 = 14 +0.05 I2. According to this relationship, we can determine the required voltage. When setting the voltage, we expect the decline in voltage during load. The voltage drop is approximately

4.5-5.0 V at 100 A. Set the welding current by setting the welding voltage first and then configure

the wire feed speed to the point, where the burning of the arc is ideal.

27/31

Please note that the actual settings for ideal arc may vary slightly depending on the position of the weld material and voltage fluctuations.

To achieve a good quality of the welds and the optimum setting of the welding current it is necessary to ensure that the distance of the power nozzle from the material was about 10 times the diameter of the welding wire (pic. 11).

Fig. 11 – Distance from nozzle to material

11. MMA WELDING (COATED ELECTRODE- ELE)

1. Choose MMA method (see SETTING THE METHOD OF WELDING).

2. Left display V10 shows the value of welding current, right display V11 shows ELE.

3. Welding current set by the encoder V5.

4. During welding, the left display V10 shows measured value of welding current and the right display V11 shows voltage.

5. After welding, on the display will remain measured value (HOLD) for 6 s.

6. If is connected the torch with remote control, on its display is shown ELE.

7. If stays connected the MIG/MAG torch, on the torch will be the

welding voltage.

8. If the machine allows to connect the remote control (connector A11), it is possible by means of the remote control (pic. 12) gently regulate the value of the welding current. If the potentiometer K1 of the remote control is turned to the extreme positions (0 or 10), the welding current can no longer be increased/reduced. (For example: If the welding current is set to 150 A on the machine and the potentiometer K1 of the remote control is turned to the extreme position 10, the welding current can no longer be increased, it can only be reduced.)

28/31

Fig. 12 – Remote control for MMA regime

12. ROUTINE MAINTENANCE & INSPECTION

1. The only routine maintenance required for the aXe range of machines is a thorough cleaning and inspection, with the frequency depending on the usage and the operating environment.

 WARNING 

2. Disconnect the aXe from the mains supply voltage before disassembling.

3. Special maintenance is not necessary for the control unit parts in the Welder. If these parts are damaged for any reason, replacement is recommended.

CAUTION 

4. Do not blow air into the welder during cleaning. Blowing air into the welder can cause metal particles to interfere with sensitive electronic components and cause damage to the welder.

5. To clean the welder, disconnect it from the mains supply voltage then open the enclosure and use a vacuum cleaner to remove any accumulated dirt and dust. The welder should also be wiped clean. If necessary, solvents that are recommended for cleaning electrical apparatus may be used.

6. Troubleshooting and repairing of the aXe welding equipment should only be carried out only by suitably qualified or competent person.

7. A ‘competent person’ must be a person who has acquired through training, qualification or experience, or a combination of them, the knowledge and skills enabling that person to safely carry out a risk assessment and repairs to the electrical equipment in question.

8. The person carrying out the servicing needs and repairs must know what to look at, what to look for and what to do.

29/31

OPERATIONAL SAFETY INSPECTION OF THE MACHINE ACCORDING TO ČSN EN 60 974-4

Prescribed operations of tests, procedures, and required documentation are listed in ČSN EN 60974-4. SERVIS

ERROR MESSAGES

The left display V10 shows Err, the right display V11 shows number / marking of the error.

Err 1

Overheating of the machine. DO NOT POWER OFF THE

MACHINE!

Err 2

Low water pressure. Check the amount of liquid in the tank, eventually clear the water circuit. If you cannot run the cooling unit test, check the fuse in the

cooling unit.

Err noP

Pulsed mode cannot turn on for the selected synergic program.

Err noS

Pulsed mode cannot turn off, synergic program in only for the

pulsed mode.

TROUBLE SHOOTING

ymptom

Reason

Solutio

The torch is too

hot.

Nozzle is not fixed. Tighten the nozzle.

Button on the torch does not respond.

Connectivity of EURO

connector is loose

Tighten EURO

connector

Damaged wiring in the

torch

Check and replace if

necessary

Irregular wire feed or wire is caked to the nozzle.

The wire on the spool is too tightly wound.

Check and replace the spool if necessary.

The ball is fused to the nozzle.

Cut out the ball and piece of the wire at the

beginning.

Irregular or no wire feed.

Poor pressure in the wire feed rolls.

Adjust the pressure according to this

instruction manual

The torch is damaged.

Check and replace if

necessary

The groove on the feed roll does not correspond to the

welding wire diameter.

Put the correct roll.

Bad quality of the wire.

Check and replace if necessary.

The liner in the torch is

unclean or damaged.

Check and replace if

necessary

30/31

Spool brake is badly

configured.

Adjust it according to this

instruction manual

Arc or short circuit between the hose

and the nozzle

Glued spatter inside the gas nozzle.

Remove the spatter.

Unstable arc.

Incorrect diameter of the nozzle or too worn out or damaged nozzle.

Change the nozzle.

Inadequate supply of a protective gas, pores in the weld.

Poorly set the amount of supplied gas.

Set the correct amount as described in this

instruction manual

Reducing valve on the

bottle is dirty

Check and replace if

necessary

The torch or gas hoses

are dirty

Check and replace if

necessary

Protective gas is blown

away by draft.

Stop the draft.

Bad welding power.

Missing phase.

Try to connect the machine to a different outlet. Check the power supply cable and circuit

breaker.

Poor grounding.

Ensure the best connection between the work piece and the earthling cable / clamps

of the machine. The grounding cable is poorly attached to the connector on the

machine

Tighten the earthling

cable in the connector on

the machine.

Torch damaged.

Check and replace if

necessary.

During feeding welding wire is rubbed.

The groove on the feed roll does not correspond to the welding wire diameter.

Put the correct roll.

Wrong pressure in the upper wire feed roll.

Adjust the pressure

according to this

instruction manual

31/31

STATEMENT OF WARRANTY

1. In accordance with the warranty periods stated below, ALFA IN guarantees the proposed product to be free from defects in material or workmanship when operated in accordance with the written instructions as defined in this operating manual.

2. ALFA IN welding products are manufactured for use by commercial and industrial users and trained personnel with experience in the use and maintenance of electrical welding and cutting equipment.

3. ALFA IN will repair or replace, at its discretion, any warranted parts or components that fail due to defects in material or workmanship within the warranty period. The warranty period begins on the date of sale to the end user.

4. If warranty is being sought, please contact your ALFA IN product supplier for the warranty repair procedure.

5. ALFA IN warranty will not apply to:

a. Equipment that has been modified by any other party other than

ALFA IN’s own service personnel or with prior written consent obtained from ALFA IN Service Department.

b. Equipment that has been used beyond the specifications

established in the operating manual.

c. Installation not in accordance with the installation/operating

manual.

d. Any product that has been subjected to abuse, misuse, negligence

or accident.

e. Failure to clean and maintain (including lack of lubrication,

maintenance and protection), the machine as set forth in the operating, installation or service manual.

6. Within this operating manual are details regarding the maintenance necessary to ensure trouble free operation.



NOTE



Warranty repairs must be performed by either an ALFA IN Service Centre, an ALFA IN distributor or an Authorized Service Agent approved by the company ALFA IN.

13. DISPOSAL

Only for EU countries. Do not dispose of electric tools together with household waste material.

In accordance with European Council Directive 2002/96/EC on electrical and electronic equipment waste and its implementation in accordance with national law, electric tools that have reached the end of their service life must be collected separately and returned to an environmentally compatible recycling facility.

Alfa IN aXe 250 PULSE Smart (AL), aXe 320 PULSE Smart (AL), aXe 250 Smart, aXe 320 Smart Instruction Manual

Specifications and Main Features

Frequently Asked Questions

User Manual