Alfa Next 200 User guide

Download

Page 1

Instruction

manual

200

Page 2

Page 3

Important safety instructions

When using an electrical appliance, basic safety should always be followed, including the following:

Read all instructions before using this sewing machine.

DANGER - To reduce the risk of electric shock:

1. An appliance should never be left unattended when plugged in.

2. Always unplug this appliance from the electric outlet immediately after using and before cleaning.

WARNING -To reduce the risk of burns, fire, electrical shock, or

injury to persons:

1. Read the instruction carefully before you use the machine

2. Keep the instructions at a suitable place close to the machine and hand it over if you give the machine to a third party.

3. Use the machine only in dry locations. Never leave the machine unattended with children or elderly people due to

4. they may not be able to estimate the risk.

5. This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved.

6. Children shall not play with the appliance.

7. Cleaning and user maintenance shall not be made by children without supervision.

8. Always switch off the machine if you carry out preparation for work (change the needle, feed the yarn thru the machine, change the footer, etc.).

9. Always unplug the machine if you leave it unattended, to avoid injury by expediently switch on the machine.

10.Always unplug the machine if you changing the lamp or carry out maintenance (oiling, cleaning).

11.Don't use the machine if it's wet or in humid environment.

12.Never pull at the cord, always unplug the machine by gripping the plug.

13.If the LED lamp is damaged or broken, it must be replaced by the manufacturer or its service agent or a similarly qualified person, in order to avoid a hazard.

14.Never place anything on the pedal.

15.Never use the machine if the air vents are blocked keep the air vents of the machine and the foot pedal free from dust, fusel and leftovers.

I

Page 4

Important safety instructions

16.The machine may only be used with foot pedal type C-8001.

17.The sound pressure level at normal operation is smaller than 75dB(A).

18. Do not dispose of electrical appliances as unsorted municipal waste, use separate collection facilities.

19. Contact your local government for information regarding the collection systems available.

20. If electrical appliances are disposed of in landfills or dumps, hazardous substances can leak into the groundwater and get into the food chain, damaging your health and well-being.

21. When replacing old appliances with new ones, the retailer is legally obligated to take back your old appliance for disposal at least for free of charge.

22. The appliance is not to be used by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction. (For outside Europe)

23. Children being supervised not to play with the appliance. (For outside Europe)

SAVE THESE INSTRUCTIONS

This sewing machine is intended for household use only.

II

Page 5

Contents

PRINCIPAL PARTS OF THE MACHINE ....................................................1

MACHINE CONTROL BUTTONS........................................................2-3

Operation buttons (see page 24/25).....................................................2

Function buttons (see page 26/27/28) ...................................................2

Selection buttons (see page 29/30) .....................................................3

LCD SCREEN.......................................................................4-5

PATTERN CHART....................................................................6-7

ACCESSORIES .......................................................................8

CONNECTING THE MACHINE TO THE POWER SOURCE.....................................9

Connecting the machine..............................................................9

WINDING THE BOBBIN.............................................................10-11

INSERTING THE BOBBIN..............................................................12

THREADING THE UPPER THREAD ...................................................13-14

USING THE NEEDLE THREADER .......................................................15

RAISING UP THE LOWER THREAD......................................................16

CUTTING THE THREAD ...............................................................16

TWO-STEP PRESSER FOOT LIFTER.....................................................17

STARTING SEWING...................................................................18

Start/stop button...................................................................18

Foot control.......................................................................18

THREAD TENSION ...................................................................19

CHANGING THE PRESSER FOOT.......................................................20

TYPE OF PRESSER FOOT CHART ......................................................21

MATCHING NEEDLE/ FABRIC/ THREAD..................................................22

REPLACING THE NEEDLE.............................................................23

TO RAISE OR DROP THE FEED DOGS...................................................23

OPERATION BUTTONS.............................................................24-25

Start/stop button...................................................................24

Reverse button....................................................................24

Auto-lock button ...................................................................25

Needle up/ down position button ......................................................25

FUNCTION BUTTONS ..............................................................26-28

Stitch width adjustment button ........................................................26

Stitch length adjustment button........................................................27

MODE selection button..............................................................27

Elongation button (see page 59).......................................................27

Mirror button (see page 60) ..........................................................28

Twin needle button (see page 61) .....................................................28

SELECTION BUTTONS.............................................................29-30

Direct pattern selection and number buttons .............................................29

Edit button........................................................................30

Memory button ....................................................................30

Clear button ......................................................................30

USEFUL SKILLS...................................................................31-32

Sewing corners....................................................................31

Reverse..........................................................................31

Free arm.........................................................................31

Installing the extension table..........................................................32

Sewing on heavy fabric..............................................................32

NEEDLE POSITION AND STITCH LENGTH................................................33

ZIGZAG STITCHES...................................................................33

STRETCH STITCHES .................................................................34

III

Page 6

Contents

OVERCASTING STITCHES.............................................................35

Using the overcasting foot ...........................................................35

Using the all purpose foot............................................................35

BLIND HEMS........................................................................36

BUTTON SEWING....................................................................37

BUTTONHOLE STITCHING..........................................................38-41

Making a buttonhole on stretch fabrics..................................................41

BAR TACK STITCH...................................................................42

EYELET STITCH .....................................................................43

DARNING STITCH .................................................................44-45

ZIPPER INSERTION................................................................46-47

Inserting a centered zipper...........................................................46

Inserting a lapped zipper.............................................................47

NARROW HEMMING..................................................................48

CORDING...........................................................................49

Single cording.....................................................................49

Triple cording .....................................................................49

SATIN STITCH SEWING ...............................................................50

QUILTING ..........................................................................51

GATHERING.........................................................................52

SMOCKING .........................................................................53

FREE MOTION DARNING, EMBROIDERY AND MONOGRAMMING. . . . . . . . . . . . . . . . . . . . . . . . . . 54-55

Darning..........................................................................54

Embroidery.......................................................................55

Monogramming....................................................................55

WALKING FOOT .....................................................................56

FAGOTING..........................................................................57

PATCHWORK STITCHING..............................................................57

SCALLOPING........................................................................58

Scallop hem ......................................................................58

Scallop edging ....................................................................58

ELONGATION .......................................................................59

MIRROR IMAGE .....................................................................60

USING THE TWIN NEEDLE.............................................................61

MEMORY.........................................................................62-65

Combining patterns or letters.......................................................62-63

Adding patterns or letters............................................................63

Editing patterns....................................................................64

Clearing patterns or letters...........................................................64

Recalling and sewing the memorized pattern.............................................65

WARNING FUNCTIONS.............................................................66-67

Warning animation message display ...................................................66

Instruction animation message display..................................................66

Warning beeping sound .............................................................67

BUZZER SOUND.....................................................................68

MAINTENANCE ...................................................................69-70

Cleaning the screen ................................................................69

Cleaning the sewing machine surface ..................................................69

Cleaning the hook...............................................................69-70

TROUBLE SHOOTING GUIDE........................................................71-72

IV

Page 7

Principal parts of the machine

Tension dial

Speed limiting adjustment lever

Needle up/down position button

Auto-lock button Reverse button Start/stop button

Bobbin winder spindle

LCD screen

Function

Thread cutter

Buttonhole lever

Auto needle threader

Bobbin cover plate

Sewing table and accessory box

Bobbin winder stopper

Hole for second spool pin

Handwheel

Horizontal spool pin

buttons

Selection buttons

Function

buttons

Stitch pattern plate

Bobbin thread guide

Upper thread guide

Handle

Main power switch

Power cord

Foot controller connector

Presser foot lifter

Drop feed lever

1

Page 8

Machine Control Buttons

A. Operation buttons (see page 24/25)

1. Start/stop button

Press this button to start or stop the machine.

2. Reverse button

Hold down this button to sew stitches in reverse or sew reinforcement stitches at a low speed.

3. Auto-lock button

Hold down this button to sew locking stitches immediately or at the end of the current patterns and automatically stop.

4. Needle up/down position button

Press this button to move the needle to either up or down position. Needle will be programmed to stop in selected position until button is pressed again.

B. Function buttons (see page 26/27/28)

5. Mode selection button

Press this button to select direct mode, utility and decorative pattern mode, block letter mode, script letter mode and outline letter mode.

6. Stitch width adjustment buttons

Press this button to adjust the width of the zigzag stitch.

2

Page 9

Machine Control Buttons

7. Stitch length adjustment buttons

Press this button to adjust the length of the stitch.

8. Twin needle button

Press this button to fix the width range when using the twin needle to sew.

9. Mirror button

Press this button to sew a reflection pattern.

10. Elongation button

Pattern 28 to 51 can be elongated up to five times its normal length by pressing this button.

C. Selection buttons (see page 29/30)

11. Edit button

Press this button to set an added pattern when sewing combinations of decorative stitches.

12. Memory button

Press this button to enter or store the created pattern combination in the memory.

13. Clear button

If an incorrect pattern is selected or memorized, pressing this button will clear it.

14. Direct pattern selection and number buttons

Instant access to direct pattern or press number buttons of the pattern number to select the desired pattern.

15. Speed limiting adjustment lever

Slide this lever to change the sewing speed.

3

Page 10

LCD Screen

Pattern

Reverse

Auto-lock

Needle up

position

Twin needle

Needle down

position

Pattern number

Suggested presser foot and identification letter

Stitch length

Bobbin winding

Buttonhole lever

Sound on

Pattern

TensionNeedle position

MirrorA u t o - s t o p

S o u n d o f f

Sound off

Alphabet

Pattern number

Stitch width

Stitch length

Suggested presser foot and identification letter

TensionStitch width

4

Page 11

LCD Screen

Memory

Editing patterns

Edit mode

Memory group

Number of

current unit

Sewing the memorized pattern

EDIT

Total number

of unit

Memory mode

Elongation

Pattern to edit

Elongation

Amount of elongation

5

Page 12

Pattern Chart

The portion marked in colored on the chart below shows the one unit of each pattern.

Patterns

Direct Patterns-10

A Group Patterns-100

123 45 67 890

00 01 02 03 04 05 06 07 08 09 10

21 22

41 42

61 62 63 64 65 66 67 68 69 70

80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99

43 44 45

25 26

48 49

11 12

30 31 32 33 34 35 36 37 38 39

53 54

15 16

55 56

76 77 78 79

18 19

Alfa stitch:

Stitch 78 can be used with the "spear point" needle. While this needle is in use, the auto threader should not be used.

B Group Patterns-100

00 01 02 03 04 05 06 07 08 09 10

21 22

25 26

30 31 32 33 34 35 36 37 38 39

11 12

15 16

18 19

6

Page 13

Pattern Chart

41 42 49

45 55 56

474440 43

52 53 54

5946

61 62 63 64 66 67 68 69 70

93 94 95 96 97 98 999280 81 83 84 85 86 88 89 9187 90

76 77 78 79

Alfa stitch:

Stitch 12 can be used with the "spear point" needle. While this needle is in use, the auto threader should not be used.

Alphabets

Block style

01 02

11 12

37 38

04 05 06 07 08 09 10

15 16

41 42

18 19 20

21 22

48 49 50 51 52

25 26

28 29

30 31 32 33 34 35 36

58 59 60 61 62

90 91 92

Script style

01 02

11 12

37 38

90 91 92

68 69 70

94 95 96 97

04 05 06 07 08 09 10

15 16

41 42

68 69 70

94 95 96 97

71 72

18 19 20

71 72

21 22

48 49 50 51 52

7

25 26

80 81

28 29

80 81

30 31 32 33 34 35 36

84 85 86 87 88

58 59 60 61 62

84 85 86 87 88

Page 14

Accessories

1 2 3

10 11

15 16

Standard

1. All purpose foot (T)

2. Zipper foot (I)

3. Buttonhole foot (D)

4. Overcasting foot (E)

5. Blind hem foot (F)

8

6. Satin stitch foot (A)

7. Button sewing foot (H)

8. Bobbin (3x)

9. Spool holder (Large)

10.Spool holder (Small)

11.Spool pin felt

12.Second spool pin

13.Screwdriver (L & S)

Edge/quilting guide

14.

15.Brush/ Seam ripper

16.Needle (3x)

Optional

17 18

17.Hemmer foot (K)

18.Cording foot (M)

19.Quilting foot (P)

20.Darning/ Embroidery foot

21.Gathering foot

22.Walking foot

23.Twin needle

24.Rigid cover

25.Extension table

23 24 25

Please Note:

- Accessories are stored inside the accessory box.

- Optional accessories are not supplied with this machine; they are however available as special

accessories from your local dealer.

Page 15

Connecting the machine to the power source

Caution:

Always make sure that the machine is unplugged from power source and the main switch is on ("O"). when the machine is not in use and before inserting or removing parts.

After switching off, it will take some time to consume the residual power in the circuitry.The light does not turn off immediately after switching off the power. This is normal phenomenon for an energy efficient appliance.

OFF

Connecting the machine

Before connecting the power supply, make sure that the voltage and frequency shown on the machine is conforming with your electrical power.

Place the machine on a stable table.

1. Connect the power line cord to the machine by inserting the 2-hole plug into the terminal box.

2. Connect the power line plug to the electric outlet.

3. Turn on the power switch.

4. The sewing lamp will light up when the switch is turned on.

To disconnect, turn the power switch to the off position, then remove plug from outlet.

Polarized plug information

This appliance has a polarized plug (one blade wider than the other), to reduce the risk of electrical shock; this plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. Do not modify the plug in any way.

9

Page 16

Winding the bobbin

Place the thread and spool holder onto the spool pin.

For smaller spools of thread, place spool holder with the small side next to the spool or use the small spool holder.

Snap the thread into the thread guide .

Wind the thread clockwise around the bobbin

contrary

winder tension discs.

Place the thread end through one of the inner holes in

the bobbin as illustrated and place empty bobbin on the spindle.

Push the bobbin to right.

10

Page 17

Winding the bobbin

When the bobbin winder spindle is pushed to the right,

which is the "bobbin winding position", the symbol " " appears on the LCD screen.

The symbol will disappear from the LCD screen when the bobbin winder spindle is pushed to the left, which is the "sewing position".

Hold the thread tail securely in one hand.

Press on the foot control or the Start/Stop button to

start winding the bobbin.

After the bobbin has wound a few turns stop the

machine and cut the thread near the hole of the bobbin. Continue filling the bobbin until it is full. The motor stops automatically when the bobbin is full. Stop the machine. Push the bobbin winder spindle to left.

Cut the thread and then remove the bobbin.

Please Note:

When the bobbin winder switch is placed on the right, "bobbin winding position", the machine will not sew and the handwheel will not turn. To start sewing, push the bobbin winder switch to the left "sewing position".

11

Page 18

Inserting the bobbin

Attention:

Turn power switch to off ("O") before inserting or removing the bobbin.

When inserting or removing the bobbin,

the needle must be fully raised.

Open the needle plate cover. Insert the bobbin in the bobbin case with the

thread running in a counterclockwise direction (arrow).

Pull the thread through the slit (A).

With a finger held gently on top of the

bobbin.

Draw

the thread at the arrow markings into

the stitch plate thread guide from (A) to (B)

Pull the thread at the arrow markings into

the stitch plate thread guide from (B) to (C). To cut off excess thread pull thread back

over the cutting off blade at point (C). Close the needle plate cover.

12

Page 19

Threading the upper thread

Please Note:

It is important to carry out the threading correctly as by not doing so several sewing problems could result.

Start by raising the needle to its highest point, and also raise the presser foot to release the tension discs.

Place the thread and spool holder onto the spool pin. For

smaller spools of thread, place spool holder with the small side next to the spool or use the small spool holder.

Draw the thread from the spool through the upper thread

guide.

13

Page 20

Threading the upper thread

Guide the thread around the thread guide pulling the

thread through the pre-tension spring as illustrated.

Thread the tension module by passing the thread

between the silver discs.

Then, down and around the check spring holder.

7 8

At the top of this movement, pass the thread from right to

the left through the slotted eye of the take-up lever and then downwards again.

Pass the thread behind the flat, horizontal thread guide.

Guide the thread through the wire loop.

Pull the end of the thread through the needle from front

to rear, and pull out about 10 cm of thread. Use the needle threader to thread the needle. (On the

next page.)

14

Page 21

Using the needle threader

Attention:

Turn power switch to the off position ("O").

Raise the needle to its highest position and lower the presser foot.

Lower the needle threader lever slowly and

draw the thread through the thread guide as illustrated and then to the right.

The needle threader automatically turns to

the threading position and the hook pin passes through the needle eye.

Take the thread in front of the needle.

Hold the thread loosely and release the

lever slowly. The hook will turn and pass the thread through the needle eye forming a loop.

Pull the thread through the needle eye.

15

Page 22

Raising up the lower thread

Hold the upper thread with the left hand.

Turn the handwheel towards you (counterclockwise) lowering, then raising the needle.

Gently pull on the upper thread to bring

the bobbin thread up through the needle plate hole. The bobbin thread will come up in a loop.

Cutting the thread

Pull both threads to the back under the

presser foot.

Raise the presser foot. Remove the fabric, draw the threads to the left side of the face cover and cut using the thread cutter.

The threads are cut at the proper length to start the next seam.

16

Page 23

Two-step presser foot lifter

The presser foot lifter raises and lowers your presser foot.

When sewing several layers or thick fabrics, the presser foot can be raised a second stage for easy positioning of the work.

Please Note:

The needle must always be at the highest position.

17

Page 24

Starting sewing

Start/stop button

The machine will start running when Start/stop button is pressed and will stop when pressed the second time.

The machine will rotate slowly at the beginning of the sewing.

The speed limiting adjustment lever can control the sewing speed. To increases the speed, slide the lever to the right , To decrease the sewing speed, slide the lever to the left.

Foot control

With the sewing machine turned off, insert the foot control plug into its connector on the sewing machine.

Turn on the sewing machine, and then slowly depress the foot control to start sewing.

Release the foot control to stop the sewing machine.

Attention:

Consult a qualified electrician if in doubt as how to connect the machine to the power source. Unplug the power cord when the machine is not in use.

18

Page 25

Thread tension

Loose

Tight

- Basic thread tension setting: "4"

- To increase the tension, turn the dial to the next number up. To reduce the tension, turn the dial to the next number down.

- Proper setting of tension is important to good sewing.

- For all decorative sewing you will always obtain a nicer stitch and less fabric puckering when the upper thread appears on the bottom side of your fabric.

Reverse side

Surface

Normal thread tension for straight stitch sewing.

Upper thread

Bobbin thread

Thread tension is too loose for straight stitch sewing. Turn dial to higher number.

Thread tension is too tight for straight stitch sewing. Turn dial to lower number.

Normal thread tension for zig zag and decorative sewing.

19

Page 26

Changing the presser foot

Attention:

Turn power switch to off ("O") when carrying out any of the below

operations!



Attaching the presser foot holder

Raise the presser foot bar (a). Attach the presser foot holder (b) as illustrated.



Attaching the presser foot

Lower the presser foot holder (b) until the cut-out (c) is directly



above the pin (d). Press the black lever (e).







Lower the presser foot holder (b) and the presser foot (f) will engage automatically.

Removing the presser foot

Raise the presser foot. Press the black lever (e) and the foot will disengages.

Attaching the guide



Attach the guide (g) in the slot as illustrated. Adjust according to need for hems, pleats, etc.

edge/quilting

20

Page 27

Type of presser foot chart

PRESSER FOOT PRESSER FOOT

All purpose foot (T)

Zipper foot (I)

Buttonhole foot (D)

APPLICATION

General sewing, Patchwork stitches, Decorative stitching, Smocking, Fagoting, etc.

Inserting zippers

Buttonhole sewing, Darning-stitch sewing

Cording

NEEDLE NEEDLE

Satin stitch foot (A)

Quilting foot (P) (Optional)

APPLICATION

Satin stitch sewing

Quilting

Free-motion darning, embroidery, monogramming

Cording foot (M) (Optional)

Overcasting

Overcasting foot (E)

Blind hem stitching

Blind hem foot (F)

Narrow hemming

Rolled hem foot (K) (Optional)

Darning/ Embroidery foot (Optional)

Gathering foot (Optional)

Button sewing foot

Walking foot (Optional)

Gathering

Button sewing

This foot helps to prevent uneven feeding of quilt layers, napped fabrics, and difficultto-handle fabrics.

Please Note:

- The twin needle is optional. It is not include with the accessories.

- When sewing with twin needle, the stitch width should be set at less than "5.0".

21

Page 28

Matching needle/ fabric/ thread

NEEDLE, FABRIC, THREAD SELECTION GUIDE

NEEDLE SIZE

FABRICS

THREAD

9-11 (70-80) Lightweight fabrics-thin cottons, voile,

serge, silk, muslin, Qiana, interlocks, cotton knits, tricot, jerseys, crepes, woven polyester, shirt & blouse fabrics.

11-14 (80-90)

14 (90)

16 (100)

18 (110)

Please Note:

- In general, fine threads and needles are used for sewing fine fabrics, and thicker threads are used for sewing heavy fabrics.

- Always test thread and needle size on a small piece of fabric which will be used for actual sewing.

- Use the same thread for needle and bobbin.

- Use a backing for fine or stretchy fabrics.

Medium weight fabrics-cotton, satin, sailcloth, double knits, lightweight woollens.

Medium weight fabrics-cotton duck, woolen, heavier knits, terrycloth, denims.

Heavyweight fabrics-canvas, woolens, outdoor tent and quilted fabrics, denims, upholstery material (light to medium).

Heavy woollens, overcoat fabrics, upholstery fabrics, some leathers and vinyls.

Light-duty thread in cotton, nylon, polyester or cotton wrapped polyester.

Most threads sold are medium size and suitable for these fabrics and needle sizes.

Use polyester threads on synthetic materials and cotton on natural woven fabrics for best results.

Always use the same thread on top and bottom.

Heavy duty thread, carpet thread.

22

Page 29

Replacing the needle



Attention:

Turn power switch to off ("O") when carrying out any of the above operations!

Change the needle regularly, especially if it is showing signs of wear and causing problems. Insert the needle following the illustrated instructions.

A. Loosen the needle clamp screw and

tighten again after inserting the new needle. The flat side of the shaft should be towards the back.

B. Insert the needle as far up as it will go.

Needles must be in perfect condition. Problems can occur with:

- Bent needles

- Blunt needles

- Damaged points

To raise or drop the feed dogs

With the sewing table off the machine, the feed dog adjustment lever can be seen on the base in back of the sewing machine.

Sliding the lever to the " " (b) will lower the feed dog, for example during button sewing. If you wish to continue sewing normally, slide the lever to the " " (a) in order to raise the feed dogs.

The feed dog will not rise up if you do not turn the handwheel, even if the lever is slid to the right. Make a complete turn to raise the feed dogs.

23

Page 30

Operation buttons

Needle up/down

position button

Auto-lock button

Reverse button

Start/stop button

Reverse button

The machine will start running when start/stop button is pressed and will stop when pressed the second time. The machine will rotate slowly at the beginning of sewing.

The sewing speed will increase slowly until reaching the speed setting selected with the speed limiting adjustment lever.

The foot control must be disconnected to complete this operation.

Select Direct Patterns 1-5, or A Group Pattern 00 and the machine will sew in reverse. An arrow " " on the LCD screen display appears while stitching in reverse. The machine will sew forward after the button is released.

If you press and reverse the button before starting to sew, the machine will permanently sew in reverse. Press the button again to sew forward again.

Select Direct patterns 6-9, A Group Patterns 01-13, 28-99, and B Group Patterns 00-99 a reinforcement stitch sews at a low speed and machine automatically stops if the reverse button is pressed.

24

Page 31

Operation buttons

Auto-lock button

When Direct Patterns 1-9, and A Group Pattern 00-05, 07-11 are selected, the machine will immediately sew 3 locking stitches when the Auto-lock button is pressed, then automatically stop.

The LCD screen will display the figure " " until the machine is stopped.

When A Group Patterns 06, 12-13, 28-99, and B Group Patterns 00-99 are selected, press the Auto-lock button, the machine will sew 3 locking stitches at the end of the current pattern and automatically stop.

The function will be cancelled if you press the button once again or select another pattern.

The LCD screen will display the figure " " until the machine is stopped.

Needle up/ down position button

With the Needle up/ down position button, you decide whether the needle shall stop in the up position or in the material when you stop sewing.

When you press the button so that the arrow (which displays just to the right of the needle icon on the LCD screen) will point upward, the needle will stop in the highest position.

When you press the button so that the arrow (which displays just to the right of the needle icon on the LCD screen) points downward, the machine will stop with the needle in the lowest position.

25

Page 32

Function buttons

Stitch width adjustment button

Stitch width adjustment buttons

Mode selection button

Stitch length adjustment buttons

Twin needle button

Mirror button

Elongation button

When you select a stitch, the machine will automatically set the recommended stitch width, which will be indicated by numbers on the LCD screen. The stitch width can be regulated by pressing the stitch width adjustment buttons.

Certain stitches have a limited stitch width.

For a narrower stitch, press the " – " button (left). For a wider stitch, press the " + " button (right).

The stitch width can be adjusted between "0.0-7.0".

Certain stitches have a limited stitch width.

When Pattern 00 is regulated by the stitch width adjustment buttons. Pressing the " – " button (left), will move the needle to the left and pressing the " + " button (right), will move the needle to the right. The numbers will be changed from left position "0.0" to extreme right position "7.0". The pre-set center needle position will be indicated as "3.5".

Direct Patterns 1-4, and A Group

are selected, the needle position

26

Page 33

Function buttons

Stitch length adjustment buttons

MODE selection button

When you select a stitch the machine will automatically set the recommended stitch length which will be indicated by numbers on the LCD screen. The stitch length can be adjusted by pressing the stitch length adjustment buttons.

To shorten the stitch length, press the " – " button (left). For a longer stitch length, press the "+" button (right). The stitch length can be adjusted between "0.0-4.5". Certain stitches have a limited length.

Elongation button (see page 59)

The LED light will be set at direct mode " " when start the machine. By pressing the button, LED light will move step by step to select the stitch mode, as shown.

Direct mode stitch selection.

Utility and satin pattern mode:

Stitch selection using number buttons.

Decorative pattern mode:

Character selection using number buttons.

Block letter mode:

Character selection using number buttons.

Script letter mode:

Character selection using number buttons.

A Group Patterns 28-51 can be elongated up to five times its normal length by pressing the " " button.

When the width or length or stitch is changed, a greater variety of patterns are available.

27

Page 34

Function buttons

Mirror button (see page 60)

The Direct Patterns 1-9, A Group Patterns 00-13, 28-99, and B Group Patterns 00-99 can be mirror imaged along a vertical axis by pressing the " " button. The machine will continue to sew the reflected pattern until the mirror button is pressed again. The mirror function also will be canceled if the pattern changed.

The function for mirror imaging the pattern appears on the LCD screen.

Twin needle button (see page 61)

With the twin needle, the Direct Patterns 1-9, A Group Patterns 00-13, 28-99, and B Group Patterns 00-99 can be sewn in two parallel lines of the same stitch with two different threads.

Press the " " button, the machine automatically reduces the maximum width for twin needle sewing. Press the button again for single needle sewing.

28

Page 35

Selection buttons

Direct pattern selection and number buttons

Edit button

Memory button Clear button

Direct pattern selection and number buttons

Direct pattern selection Press the buttons to select the utility patterns

shown beside the number button when the mode button is set at the Direct mode.

Number buttons To select the desired pattern and press the

number buttons . Except the Direct Pattern mode, the other

mode can be selected by pressing the desired numbers.

For example: pattern 60

29

Page 36

Selection buttons

Edit button

Memory button

If you wish to modify any settings in the memory mode, use the stitch width " + " or

button to select the pattern to be modified,

" and press the " " button to set the selected pattern under the editing mode, the LED light will turn on. Manual setting function of the stitch width, stitch length, mirror, elongation and auto-lock for these memorized patterns is now possible. Press the " " button again to leave the editing mode and return to memory mode.

Press the " " button to enter the memory mode, and store the combinations of characters or decorative stitches. Use the stitch width " + " or button to confirm the pattern memorized by pressing this button in memory mode.

" – "

" –

Clear button

Please Note:

The Direct mode patterns and the A Group Patterns 14-27 cannot be memorized.

Press this button when the incorrect character is selected. Each press of this button erases one character, or press this button to remove an added pattern when sewing combinations of characters or decorative stitches.

30

Page 37

Useful skills

Sewing corners

1. Stop the sewing machine when you reach a corner.

2. Lower the needle into the fabric manually or by pressing the needle up/ down button

once.

3. Raise the presser foot.

4. Use the needle as a pivot and turn the fabric.

5. Lower the presser foot and resume sewing.

Reverse

Reverse stitching is used to secure the threads at the beginning and at the end of a seam.

Press the reverse button and sew 4-5 stitches. The machine will sew forward when the button is released.

Free arm

Free-arm sewing is convenient for sewing tubular areas such as pant hems and cuffs.

31

Page 38

Useful skills

Installing the extension table

* The accessory is optional.

Extension table

It is not included with this machine.

Pull the sewing table and accessory box off

by sliding it to the left.

Follow the arrow, and stretch the foot of the

extension table.

Snap (A) of the extension table into (B) of

the machine.

Extension table can help moving during sewing.



Sewing on the heavy fabric

The black button on the right side of the presser foot will lock the presser foot in a horizontal position if you push it in before lowering the presser foot. This ensures even feeding at the beginning of a seam and helps when sewing multiple layers of fabric such as sewing over seams when hemming jeans.

When you reach the point of an increased thickness, lower the needle and raise the presser foot. Press the toe of the foot and push in the black button, then lower the foot and continue sewing.

Cardboard or

thick fabric

The black button releases automatically after sewing few stitches.

You also can place another piece of fabric with the same thickness at the back of the seam. Or support the presser foot while feeding by hand and sewing toward the folded side.

32

Page 39

Needle position and stitch length

A-00

Changing the needle position

These setting apply only to Group Pattern 00 center position. When you press the "–" of stitch width adjustment button, the needle position will be moved to the left. When you press the "+" of stitch

0.0 2.0

3.5

2.01.00.5

5.0 7.0

3.0

4.5

width adjustment button, the needle position will be moved to the right. On the LCD screen, the point illustration and the number indicate the needle position.

Changing the stitch length

To shorten the stitch length, press the "–" of stitch length adjustment button. For a longer stitch length, press the "+" of stitch length adjustment button.

Generally speaking, the thicker the fabric, thread and needle, the longer the stitch should be.

Direct Patterns 1-4, or A

. The pre-set position is "3.5",

Zigzac stitches

3.0

1.00.0

2.01.00.5

3.0

7.05.0

4.5

Adjusting the stitch width

The maximum zigzag stitch width for zigzag stitching is "7.0" ; however, the width can be reduced on any patterns. The width increases as you press the " + " of stitch width adjustment button from "0.0-7.0".

Adjusting the stitch length

The density of zigzag stitches increase as the setting of stitch length approaches "0.3".

Neat zigzag stitches are usually achieved at "1.0-

2.5". Closed up zigzag stitches (close together) are

referred to as a satin stitch.

33

Page 40

Straight stretch stitch

Straight stitch

Stretch stitch

3 4

7 7

Use this stitch with knitted, tricot or other

stretchy fabrics. The stitch enables your seam to stretch without breaking the thread.

Good for easy to ravel and knit fabrics. It is good for joining durable fabric such as denims.

These stitches can also be used as a decorative top stitch.

Straight stretch stitch is used to add triple

reinforcement to stretch and hardwearing seams.

Triple zigzag stretch stitch is suitable for firm

fabrics like denim, poplin, duck, etc.

34

Page 41

Overcasting stitches

Sewing overcasting stitches along the edges of fabric to prevent them from fraying.

5.0~7.0

2.0~3.0

Using the overcasting foot

Change the presser foot to the overcasting foot (E).

Sew the fabric with the fabric edge against

the guide of the overcasting foot.

Attention:

The overcasting foot should be used to sew with patterns 5 and 8 only and do not set the stitch width narrower than "5.0". It is possible that needle could hit the presser foot and

break when sewing other patterns and width.

6 A-02

Using the all purpose foot

2.5~5.0

2.0~3.0

Change the presser foot to the all purpose

foot (T).

Sewing the overcasting along the edge of

the fabric so that the needle drops over the edge of the fabric on the right side.

35

Page 42

Blind hem

Overcasting

stitches

Reverse

side

Reverse

side

5mm 5mm

Secure the bottoms of skirts and pants with a blind hem, this stitch will sew without stitches showing on right side of fabric.

9: Blind hem for woven fabrics

A-03 A-049

2.5~4.0

1.0~2.0



A-03: Blind hem for stretch fabrics A-04: Blind hem for stretch fabrics

Please Note:

It takes practice to sew blind hems. Always make a sewing test first.

Fold the fabric as illustrated with the wrong

side uppermost.

Place the fabric under the foot. Turn the

handwheel forwards by hand until the needle swings fully to the left. It should just pierce the fold of the fabric. If it does not, adjust the stitch width accordingly.

2 3

Adjust the guide (b) by turning the knob (a)

so that the guide just rests against the fold.

Sew slowly, guiding the fabric carefully along

the edge of the guide.

Turn over the fabric.

36

Page 43

Button sewing

Select the pattern 25 from the Group

Patterns "A" to get the button sewing stitch. Change the presser foot to the button sewing foot (H).

Move the drop feed lever to " " to lower the feed dogs.

Position the work under the foot. Place the

button in the desired position, lower the foot.

Select zig zag pattern. Adjust the stitch width

to according to the distance between the two holes of the button.

Turn the handwheel to check that the needle goes cleanly into the left and right holes of the button.

If a shank is required (ex. sew on coats or

jackets), place a darning needle on top of the button and sew.

Pull end of the upper thread to the wrong

side of the fabric, then tie it with the bobbin thread.

For buttons with 4 holes, sew through the

front two holes first, push work forward and then sew through the back two holes.

Please Note:

When you finish the work, move the drop feed control to " " to raise the feed dogs.

37

Page 44

Buttonhole stitching

Buttonhole sewing to match the size of the button is possible. For stretch fabric or thin fabric, it is recommended to use a stabilizer for a better buttonhole

finish.

A-14A-14

A-16

A-18

A-20

A-21

<;?HD;B

A-15

=;BHD;B

B;=H:;B

0: For light to medium weight fabrics

A-14: For light or medium weight fabrics

A-15: For light or medium weight fabrics

A-16: For heavier weight fabrics

A-17: For light or medium weight fabrics

A-17

A-19

<;?H?;?

?;?HD;B

B;=H:;B

A-18: For heavy weight fabrics

A-19: For jeans or trousers

A-20: For jeans or stretch fabric with a coarse

weave

A-21: For stretch fabric

Please Note:

=;BHD;B

:;BH<;B

Before sewing a buttonhole on your project, practice on a scrap piece of the same type of fabrics.

=;BHD;B

:;BH=;B

Mark the positions of the buttonhole on the fabric. The maximum buttonhole length is 3cm (1 3/16 inch). (Total of diameter + thickness of button.)

Starting

point

Attach the buttonhole foot, then pull out the button holder plate and insert the button.

The size of the buttonhole is determined by the button inserted in the button plate.

The thread should be passed through the hole in the presser foot, then be placed under the foot.

Select the buttonhole stitch. Adjust the stitch width and the stitch length to

the desired width and density. Position the fabric under the presser foot with

the front end of the buttonhole mark aligned with the center line on the buttonhole foot.

38

Page 45

Buttonhole stitching

Pull the buttonhole lever all the way down and position it behind the bracket on the buttonhole foot.

Please Note:

When you select any buttonhole pattern, the LCD screen will display the figure " ", to remind you to lower the buttonhole lever.

Before sewing, please hold the thread by hand.

Please Note:

Gently feed the fabric by hand.

Before stopping, the machine will automatically sew a reinforcement stitch after the buttonhole is sewn.

39

Page 46

Buttonhole stitching

* Buttonholes are sewn from the front of the presser foot to the back, as shown.

A-14

A-16

A-17

A-15

A-18

A-19

A-21A-20

Raise the presser foot and cut thread. To sew over same buttonhole, raise the

presser foot (will return to original position). After sewing the buttonhole stitch, raise the

buttonhole lever until it stops.

Attention:

After sewing the buttonholes, raise the buttonhole lever all the way up to its original position for other sewing.

40

Page 47

Buttonhole stitching

Cut the center of the buttonhole being careful not to cut any stitches on either side. Use a pin as a stopper at the bar tack so you do not cut too much.

Please Note:

When cutting the buttonhole with the seam ripper, do not place your hands in the cutting direction, otherwise injuries may result.

Making a buttonhole on stretch fabrics

When sewing buttonholes on stretch fabric,

hook heavy thread or cord under the buttonhole foot.

Attach the buttonhole foot and hook the gimp thread onto the back of the presser foot.

Bring the two gimp thread ends to the front of the foot and insert them into the grooves, then temporarily tie them there. Lower the presser foot and start sewing.

Set the stitch width to match the diameter of the gimp thread.

Once sewing is completed, pull the gimp

thread gently to remove any slack, then trim off any excess.

Please Note:

It is suggested that you use interfacing on the backside of the fabric.

41

Page 48

Bar tack stitch

A-22

1 2

2mm

Starting point

1 Select pattern 22 of Group

Patterns

"A" to get the bar tack stitch.

from the

Change the presser foot to the buttonhole foot.

2 Pull the button holder to the rear. Set the

button guide plate on the buttonhole foot to the desired length.

3 Position the fabric so that the needle is

2mm (1/16") in front of where you want the sewing to start, and then lower the presser foot.

4 Pass the upper thread down through the

hole in the presser foot. Pull down the buttonhole lever. The buttonhole lever is positioned behind the bracket on the buttonhole foot. Gently hold the end of the upper thread in your left hand, and then start sewing.

5 Bar tack stitches are sewn.

6 As an example, the illustration shows the

procedure for sewing bar tacks at pocket corners.

42

Page 49

Eyelet Stitch

Eyelet stitches are used for making belt holes and other similar applications.

A-23 A-24

A B C

?;B@;BD;B

A-23: Select for sewing eyelets on belts , etc A-24: Select for sewing eyelets on belts , etc

Select pattern 23 or 24 from the Group Patterns "A" to get the eyelet stitch. Attach presser the foot "A".

Press the "–" or "+" stitch width adjustment to button select the eyelet size.

Size of eyelet. A. Small: 5.0mm (3/16 inch). B. Medium: 6.0mm (15/64 inch). C. Large: 7.0mm (1/4 inch).

Lower the needle into the fabric at the beginning of the stitching, and then lower the presser foot lever.

Once sewing is completed, the machine automatically sews reinforcement stitches, then stops.

Make a hole at the center using an eyelet punch.

* Eyelet punch is not included with the

machine.

Please Note:

- When using the eyelet punch, place thick paper or some other protective sheet under the fabric before punching the hole in the fabric.

- If thin thread is used, the stitching may be coarse. If this occurs, sew the eyelet twice one on top of the other.

4 3

Page 50

Darning stitch

A-26

A-27

=;?HD;B

:;BH<;B

Mending a small hole or tear before it gets bigger can save a garment. Choose a fine thread that is the closest color to the garment.

Select pattern 26 or 27 from the Group Patterns "A" to get the darning stitch. Change the presser foot to the buttonhole foot.

Baste the upper fabric and the under fabric

together. Select the needle position. Lower the presser foot over the center of the tear.

Pull the button holder to rear.

Set the button guide plate on buttonhole foot to the desired length.

The size of one darn cycle is variable.

Stop

However, the maximum stitch length is

2.6cm (1 inch) and the maximum stitch width is 7mm (9/32 inch).

a. The length of sewing. b. The width of sewing.

Start

44

Page 51

Darning stitch

2mm

Position the fabric so that the needle is 2mm

(1/16 inch) in front of the area to be darned, and then lower the presser foot lever.

Please Note:

When lowering the presser foot, do not push in the front of the presser foot, otherwise the darning will not be sewn with the correct size.

Pass the upper thread down through the

hole in the presser foot. Pull down the buttonhole lever. The

buttonhole lever is positioned behind the bracket on the buttonhole foot.

Gently hold the end of the upper thread in your left hand, and then start sewing.

Please Note:

When you select any buttonhole pattern or darning pattern, the LCD screen will display the figure " " to remind you to lower the buttonhole lever.

Darning stitches are sewn from the front of

A-27

the presser foot to the back, as shown.

Please Note:

A-26

If the fabric does not feed, for example, because it is too thick, increase the stitch length.

If the sewing range is too big to sew, then we suggest you can sew several times (or cross sew) to get better sewing result.

45

Page 52

Zipper insertion

5mm

2cm

Reverse

side

Reverse stitches

Basting

stitching

This foot can be set to sew on each side of the zipper, the The edge of the foot guides the zipper to ensure straight placement.

1 2

3.5

Basting

stitching

Reverse

side

1.5~3.0

Attention:

Zipper foot should be used for sewing width center needle position straight stitch only. It is possible that needle could hit the presser foot and break when sewing other patterns.

Inserting a centered zipper

Place the right sides of the fabric together.

Sew a bottom seam 2cm from the right edge to the zipper bottom stop position. Sew a few stitches in reverse to lock. Increase the stitch length to maximum, set the tension below 2, and baste the remaining length of the fabric.

Press open the seam allowance. Place the

zipper face down on the seam allowance with the teeth against the seam line. Baste the zipper tape.

Attach the zipper foot. Attach the right side

of the presser foot pin to the holder when sewing the left side of the zipper.

3 4

Attach the left side of the presser foot pin to

the presser foot holder when sewing the right side of the zipper.

Stitching around the zipper.

Please Note:

When sewing, be sure that the needle does not touch the zipper, otherwise the needle may bend or break.

Remove the basting and press.

46

Page 53

Zipper insertion

The Rolled Hem Foot is used to sew rolled hems commonly found on shirt hems, table linens, and the edges of ruffles.

Inserting a side zipper

5mm

Reverse stitches

Basting

stitching

Place the right sides of the fabric together.

Reverse

side

2cm

3 4

Fold back to the left seam allowance.

Turn under the right seam allowance to form

3mm (1/8 inch) fold.

Attach the zipper foot. Attach the right side

of the presser foot pin to the holder when sewing the left side of the zipper. Attach the left side of the presser foot pin to the presser foot holder when sewing the right side of the zipper.

Stitch the left side of zipper from bottom to

top.

Turn the fabric right side out, stitch across

the lower end and right side of zipper.

5 6

47

Stop about 5cm (2 inches) from the top of

zipper. Remove the basting and open the zipper. Stitch the remainder of the seam.

Page 54

Narrow hemming

The hemmer foot is used to stitch the narrow rolled hems usually found on shirt tails, table linens and along the edge of frills.

* The Hemmer foot accessory is optional. It

is not included with this machine.

3.5

1.5~3.0

Fold edge of fabric over about 3mm (1/8 inch),

then fold it over again 3mm (1/8 inch) for about 5cm (2 inches) along the edge of the fabric.

Insert the needle into the fold by rotating the

handwheel toward you, and lower the presser foot. Sew several stitches and raise the presser foot.

Insert the fabric fold into the spiral opening of hemmer foot. Move fabric back and forth until the fold forms a scroll shape.

Lower the presser foot and start sewing

slowly guiding the raw edge of the fabric in front of the hemmer foot evenly into the scroll of the foot.

48

Page 55

Cording

Used for embellishing 1 to 3 cords or decorative threads. Sew over one strand of cording to create a pretty swirled design on a jacket or vest or sew

over three strands of cording for border trims. Pearl cotton, knitting yarn, embroidery floss, lace thread, fine wool or lily yarn can be used for cording.

* The cording foot accessory is optional. It is not included with this machine.

Single cording

Mark the design on the fabric. Insert the cord in the center groove of the

cording foot from the right side opening. Place the cord under the grooves of the

cording foot and pull the cord about 5cm (2 inches) behind the foot.

The grooves under the foot will hold the length of the cord in place while the stitches are being form over the cord.

Select the stitch and adjust the stitch width so that the stitches are just covering the cord.

Lower the foot and sew slowly, guiding the cord over the design.

6 A-10

Triple cording

Mark the design on the fabric. Insert three cords into the grooves of the foot

from the right side opening. Place the cord under the grooves of the

cording foot and pull the cord about 5cm (2 inches) behind the foot.

The grooves under the foot will hold the length of the cord in place while the stitches are being form over the cord.

Select the stitch and adjust the stitch width so that the stitches are just covering the cord.

Lower the foot and sew slowly, guiding the cord over the design.

49

Page 56

Satin stitch sewing

A-28

A-29

A-30

A-31

A-32

A-33

A-34

A-35

A-36

A-37

A-38

A-39

A-40

A-41

A-42

A-43

A-44

A-45

A-46

A-47

A-48

A-49

A-50

A-51

A-52

A-53

A-54

A-55

A-56

A-57

A-58

A-59

A-60

=;?HD;B

B;?H<;B

Use the satin stitch foot for satin stitching and sewing decorative stitches. This foot has a full indentation on the underside to allowed easy sewing over the thickness of the stitches form by closely spaced zigzag stitches, and even feeding of the fabric.

To tailor the satin or decorative stitch pattern, you may adjust the length and width of the pattern by pressing the stitch length and width adjustment buttons. Experiment with fabric scraps until you get the desired length and width.

Please Note:

When sewing very thin fabrics, it is suggested that you use interfacing on the backside of the fabric.

50

Page 57

Quilting

Sandwiching batting between the top and bottom layers of fabric is call "Quilting". The top layer is usually formed by multiple geometrically shaped pieces of materials joined together.

3.5

* The Quilting foot accessory is optional. It

Insert the e in the presser foot holder as illustrated and set the space as you desire.

Sew the first row and move over the fabric to sew successive rows with the guide riding along the previous row of stitching.

When using the quilting foot, only use center needle position stitches to prevent machine damage.

1.0~3.0

is not included with this machine.

dge/quilting guide

Please Note:

51

Page 58

Gathering

The Gathering Foot is used for gathering fabrics. Ideal for clothing as well as home decor, works best on thin to medium weight fabrics.

3.5

4.5

* The Gathering foot accessory is optional. It is

not included with this machine.

Gathered fabric

Remove the presser foot holder and attach the

gathering foot, lowering the tension setting to below 2.

Place fabric to be gathered under presser foot to the right of the presser foot.

Sew a row of stitching, keeping the raw edge of fabric aligned with the right edge of foot. The stitches automatically cause the fabric to gather.

Suitable for light to medium weight fabrics. If your fabric is light, such as batiste or lace, you will have more gathers.

To gather and attach gathered fabric in one step

Look closely at the gathering foot to see a slot

on the bottom. When using the slot, you can gather the bottom

layer of the fabric while attaching it to a flat top layer, such as the waistband on a dress bodice.

- Remove the presser foot holder and attach gathering foot.

- Place the fabric to be gathered with right side up under the foot.

- Place top layer of the fabric right side down in the slot.

- Guide the two layers as illustrated.

Please Note:

- When testing machine for adjustments to

achieve desired fullness, work with 10" increments of the fabric, trims or elastic. This makes it easier to determine the adjustments and how much change is needed for your project. Always test on your project fabric and on the same grainline as will be used in your finished project.

- Sew slow to medium speed for better fabric

control.

52

Page 59

Smocking

The decorative stitch created by stitching or embroidering over gathers is called "smocking". It is used to decorate the front of blouses or cuffs. The smocking stitch adds texture and

elasticity to fabric.

A-09 A-10

Use the all purpose foot to sew basting lines

1cm (3/8 inch) apart, across the area to be smocked.

Basting

Knot the threads along one edge.

Pull the bobbin threads and distribute the gathers evenly. Secure the threads at the other end.

Bobbin thread

Reduce the tension, if necessary and sew

decorative pattern stitches between the straight seams.

Pull out the basting.

53

Page 60

Free motion darning, embroidery and monogramming

3.5~5.0

* The Darning/ Embroidery foot accessory is

optional. It is not included with this machine.

Move the drop feed control to " " to lower

the feed dogs.

Remove the presser foot holder, and attach

the darning foot to the presser foot holder bar. The lever (a) should be behind the needle

clamp screw (b). Press the darning foot on firmly from behind with your index finger and tighten the screw (c).

Darning

First sew around the edges of the hole (to

secure the threads). Working from left to right, sew over the hole in a constant and continuous movement.

Turn the work by 1/4 and sew over the first stitching moving the work slower over the hole to separate the threads and not form big gaps between the threads.

Please Note:

Free motion darning is accomplished without the sewing machine internal feed system. Movement of the fabric is controlled by the operator. It is necessary to coordinate sewing speed and movement of fabric.

54

Page 61

Free motion darning, embroidery and monogramming

Embroidery

Select zigzag stitch pattern and adjust the

stitch width as desired. Stitch along the outline of the design by moving the embroidery hoop. Make sure to maintain a constant speed.

Fill in the design working from the outline towards the inside. Keep the stitches close together.

You will get longer stitches by moving the hoop faster and shorter stitches by moving the hoop more slowly.

Secure with a reinforcement stitches at the end by press Auto-lock button.

Monogramming

Select the zigzag stitch pattern and adjust

the stitch width as desired. Sew at a constant speed, moving the hoop slowly along the lettering.

When the letter is finished. Secure with a reinforcement stitches at the end by press Auto-lock button.

* Embroider hoop is not included with the

machine.

Please Note:

When you finish the work, move the drop feed control to " " to raise the feed dogs.

55

Page 62

Walking foot

* The walking foot accessory is optional. It is no t in cl ud ed

with this machine.

Always try to sew first without the walking foot accessory which should be used only when necessary.

It is easier to guide the fabric and you have a better view of the seam when using the standard, regular foot on your machine.

Your sewing machine offers excellent stitch quality on a wide range of fabrics from delicate chiffons to multiple layers of denim.

The Walking Foot accessory equalizes the feeding of the upper and lower layers of fabric and improves the matching of plaids, stripes and patterns. It also helps to prevent uneven feeding of very difficult fabrics.

Lift the presser foot lifter to raise the presser foot bar.

Remove the presser foot holder by unscrewing (counterclockwise) the presser bar attaching screw.

Attach the Walking Foot to the machine as follows:

- The arm (a) should fit into above the needle screw and

clamp (b).

- Slide the plastic attaching head (c) from your left to right so that it is fitted into the presser foot bar.

- Lower the presser foot bar.

- Replace and tighten (clockwise) the presser bar attaching screw.

- Make sure both the needle screw and the presser bar attaching screw are tightly secured.

Draw the bobbin thread up and place both the bobbin thread and the needle thread behind the walking foot attachment.

56

Page 63

Fagoting

Stitching across an open seam is called "fagoting". It is used on blouses and children's clothing. This stitch is more decorative when thicker thread is used.

A-08 A-06

Thin paper

Basting

Patchwork stitching

A-08 A-09 A-10 A-61

Separate the folded edges of the fabric

pieces with a gap of 4mm (1/8 inch) and baste them onto a piece of thin paper or water-soluble stabilizer sheet.

Align the center of the presser foot with the

center of the two pieces of fabric and begin sewing.

After sewing, remove the paper.

Place the two pieces of fabric with the right

side together and sew with the straight stitch.

Open the seam allowances and presses it

flat.

Place the center of the presser foot on the

seam line of the joined pieces of fabric and sew over the seam.

57

Page 64

Scalloping

The wave-shaped repeating pattern that looks like shells is called "scalloping". It is used on the collars of blouses and to decorate the edges of projects.

A-12

Wrong side of fabric

Scallop hem

Fold the fabric right side together in and sew

along the edge.

Cut the fabric along the seam leaving an

allowance of 3mm (1/8 inch) for seaming. Notch the allowance.

Turn the fabric over and push out the curved

seam to the surface and iron it.

A-13 A-35

Scallop edging

Stitch along the edge of the fabric, making

sure not to sew directly on the edge of the fabric.

For better results, apply spray starch onto the fabric and press with a hot iron before it is sewn.

Trim along the stitches.

* Be careful not to cut the stitches.

58

Page 65

Elongation

A-28

A-29

A-30

A-31

A-32

A-33

A-34

A-35

A-36

A-37

A-38

A-39

A-40

A-41

A-42

A-43

A-44

A-45

A-46

A-47

A-48

A-49

A-50

<;?HD;B

A-51

1 The stitches shown in the diagram above

B;=H:;B

can be elongated up to five times the normal length by pressing the elongation button.

2 The LCD screen icon for elongation

imaging of the pattern appears.

3 When the width or length of the stitch is

/

Longitud normal

changed, a greater variety of the selected pattern is available.

Please Note:

Patterns from A Group 28-51 can be

elongated and mirrored simultaneously.

59

Page 66

Mirror image

Please Note:

- The Direct Patterns " " and A Group Patterns 14-27 cannot be mirror imaged.

- Mirror imaged patterns can also be combined with other patterns.

1 Select the pattern.

2 Pressing the mirror button.

3 The LCD screen icon for mirror imaging of

the pattern appears.

A. Normal pattern sewing.

B. Mirror pattern sewing.

60

Page 67

Using the twin needle

When using twin needles, use the " T " presser foot regardless

<;BH?;B

of what kind of sewing will be carried out.

Please Note:

1 Insert the twin needle.

Attention:

When using twin needles, use the all purpose foot (T) regardless of what kind of sewing foot will be carried out.

Use only twin needle assemblies with max. 2mm needle distance.

2 Follow the instructions for single-needle

threading using the horizontal spool pin. Thread through the left needle. Set the second spool pin (included with the accessories) into the hole on the top of the machine. Thread through remaining points, making certain to omit the thread guide above the needle and pass thread through the right needle.

3 Thread each needle separately.

Please Note:

Make sure that the two threads used to thread the twin needle are of the same weight. You can use one or two colors.

4 Press the Twin needle button, and the

machine automatically reduces the maximum width for twin needle sewing.

6 Select a pattern and start to sew. Except the

Direct patterns " " and A Group patterns

14-27, the other patterns can be used. Two lines of stitching are sewn parallel to each other.

Please Note:

When sewing with twin needle, always proceed slowly, and make sure to maintain a low speed to insure quality stitching.

61

Page 68

Memory

Combined patterns can be stored for later use. Since stored patterns are not lost after the sewing machine is turned off, they can be recalled at any time. This is convenient for patterns such as names, which may be used frequently.

Please Note:

- Multiple patterns selecting from pattern modes , , , can be combined and sewn together.

- This machine has 4 modules of program memory and each module can retain 20 units of stitches.

- cannot be entered into memory.

The Direct mode patterns and the A Group Patterns 14-27

- All the units in the memory can be edited to set its function such as Stitch length, Stitch width, Elongation, Mirror, and Auto-lock.

Combining patterns or letters

Press " MODE " button to select any desired pattern

group among , , , on front cover.

The LED will indicate the selected group.

Press the " " button to open the memory mode and

then appears a sub-screen in the center. It is available

to select the number of the memory module when the cursor start flashing.

Press number of memory module. (e.g. 2)

The memory screen appears automatically.

62

Page 69

Memory

Press the desired pattern number. (e.g. 60)

The selected pattern displays on the LCD screen.

Repeat step 5, 6 for more patterns to be stored in the

memory.

Please Note: When the memory the full with 20 units of patterns,

the machine will beep to signal it.

Adding patterns or letters

Press the " " button to leave the memory mode and

return to the normal screen.

Attention: The selected pattern will be cleared from the

memory module after closing the machine if you do not press the " " button again when you have completed your selection.

While in the memory mode, press stitch width

adjustment button until the stitch number you have selected is displayed, then add the new stitch.

Press pattern No. (e.g. 31) The selected pattern will be

inserted.

6 3

Page 70

Memory

Editing patterns

EDIT

Use the stitch width adjustment button to select the

pattern that you wish to edit while in the memory mode.

Press the " " button to edit the pattern. The stitch

length, stitch width, Elongation, Mirror, and Auto-lock of the patterns can be adjusted manually.

Please Note:

The stitch length, stitch width, Elongation, Mirror, and Auto-lock of the patterns can be adjusted manually.

Clearing patterns or letters

Press the " " button when complete and return to

browse status.

While in the memory mode, press stitch width

adjustment button to select the pattern that you want to clear .

Press the " " button to delete the selected pattern

and the next pattern in the back will move forward.

64

Page 71

Memory

Recalling and sewing the memorized pattern

Press the " " button to enter memory mode and then

input the number of memory module when the cursor

start flashing.

Input the number of memory module. (e.g. 2)

LCD screen shows the first pattern of the selected

memory module. Select or browse memory patterns by pressing stitch

width buttons." – " or " + "

Press on the foot control or press the start/stop button

to start the sewing machine.

The screen shows the current sewing pattern.

Press the " " button to leave memory mode and

return to the normal screen.

65

Page 72

Warning functions

Warning animation message display

Instruction animation message display

The sewing machine is experiencing a problem

The animation message means that the thread is twisted or jammed and the hand wheel axle cannot move. Please look through the "Trouble shooting guide" on page 71 or 72 to find the solution. After the problem has been solved, the machine will continue to sew.

Bobbin winding

The bobbin winder is winding the bobbin.

Lower the buttonhole lever

When you select any buttonhole or darning stitch, LCD screen will be demonstrated the figure " ", it is to remind you to lower the buttonhole lever.

66

Page 73

Warning functions

Warning beeping sound

- When operating correctly: 1 beep

- When operating incorrectly: 3-short beeps

- When the sewing machine is in trouble and can't sew: 3-short beeps

It means that the thread is twisted or jammed and the hand wheel axle can't move. Please look through the "Trouble shooting guide" on page 71/72 to find the solution. After the problem has been solved, the machine will continue to sew.

Return bobbin winder spindle to left

If you press any button on the machine when the bobbin is full or the bobbin winder spindle is in the right position, then the machine will beep 3 times as a warning.

Return the bobbin winder spindle to the left position.

Please Note:

If the problem is still not solved, please contact your local dealer.

Attention:

During the sewing, if the thread get jammed inside the hook stopping the needle from moving and

you continue pressing the foot control, the security switch will stop the machine completely. In

order to restart the sewing machine, you will have to turn the on/off switch to the OFF position and

then ON again.

67

Page 74

Buzzer sound

OFF

1 Press on the " " button and turn on the

power switch at the same time.

2 You can select the mode by pressing the

stitch width " + " or " - " button. Select desired mode sound on " "or sound off " ".

3 Pressing the " " button. The Buzzer

sound setting mark will appear on the LCD screen when you have set it.

68

Page 75

Maintenance

Attention:

Disconnect the power cord from the wall socket before cleaning the screen and sewing machine surface, otherwise injury or electrical shock may result.

Cleaning the screen

If the front panel is dirty, wipe it gently with a soft, dry cloth. Do not use any organic solvents or detergents.

Cleaning the sewing machine surface

If the surface of the sewing machine is dirty, lightly soak a cloth in mild detergent, squeeze it out firmly and then wipe the surface. After cleaning it once in this way, wipe the surface again with a dry cloth.

Attention:

This machine is equipped with a 100mW LED lamp. If lamp replacement is needed, please contact nearest authorized retailer.

Cleaning the hook

If lint and bits of thread accumulate in the hook, this will interfere with the smooth operation of the machine. Check regularly and clean the stitching mechanism when necessary.

Attention:

Disconnect the machine from the wall outlet before carrying out any maintenance.

Remove the needle plate cover and bobbin.

69

Page 76

Maintenance

Remove the needle, presser foot and presser foot holder. Remove the screw holding the needle plate and remove the

needle plate.

Clean the feed dog and bobbin case with a brush. Also clean them, using a soft, dry cloth.

70

Page 77

Trouble shooting guide

Before calling for service, check the following items. If the problem still persists, contact the place of purchase or your nearest authorized dealer.

Problem

Upper thread

breaks

Lower thread

breaks

Skipped

stitches

Needle breaks

Loose stitches

Seam

gather or

pucker

Cause

1.The machine is not threaded correctly.

2.The thread tension is too tight.

3.The thread is too thick for the needle.

4.The needle is not inserted correctly.

5.The thread is wound around the spool holder pin.

6.The needle is damaged.

1.The bobbin case is not inserted correctly.

2.The bobbin case is threaded wrong.

1.The needle is not inserted correctly.

2.The needle is damaged.

3.The wrong size needle has been used.

4.The foot is not attached correctly.

5.The machine is not threaded correctly.

1.The needle is damaged.

2.The needle is not correctly inserted.

3.Wrong needle size for the fabric.

4.The wrong foot is attached.

5.The needle clamp screw is loose.

6.The presser foot that is used is not appropriate for the type of stitch that you wish to sew.

7.The upper thread tension is too tight.

1.The machine is not correctly threaded.

The bobbin case is not correctly

2. threaded.

Needle/fabric/thread combination is

3. wrong.

4.Thread tension is wrong.

1.The needle is too thick for the fabric.

2.The stitch length is adjusted wrong.

3.The thread tension is too tight.

Correction

1.Rethread the machine.

2.Reduce the thread tension (lower number).

3.Select a larger needle.

4.Remove and reinsert the needle (flat side towards the back).

5.Remove the reel and wind thread onto reel.

6.Replace the needle.

1.Remove and reinsert the bobbin case and pull on the thread. The thread should pull easily.

2.Check both bobbin and bobbin case.

1.Remove and reinsert needle(flat side towards the back).

2.Insert a new needle.

3.Choose a needle to suit the thread.

4.Check and attach correctly.

5.Rethread the machine.

1.Insert a new needle.

2.Insert the needle correctly (flat side towards the back).

3.Choose a needle to suit the thread and fabric.

4.Select the correct foot.

5.Use the screwdriver to firmly tighten the screw.

6.Attach the presser foot that is appropriate for the type of stitch that you wish to sew.

7.Loosen the upper thread tension.

1.Check the threading.

2.Thread the bobbin case as illustrated.

3.The needle size must suit the fabric and thread.

4.Correct the thread tension.

1.Select a finer needle.

2.Readjust the stitch length.

3.Loosen the thread tension.

Reference

Page 13

Page 19

Page 22

Page 23

Page 13

Page 23

Page 12

Page 23

Page 22

Page 20

Page 13

Page 23

Page 22

Page 73

Page 23

Page 73

Page 19

Page 13

Page 12

Page 23

Page 19

Page 22

Page 27

Page 19

71

Page 78

Trouble shooting guide

Problem

Seam

puckering

Patterns are

distorted

The machine

jams

The machine

is noisy

Uneven stitches,

uneven feed

The sewing

machine

doesn't

operate

Cause

1.The needle thread tension is too tight.

The needle thread is not threaded

2. correctly.

3.The needle is too heavy for the fabric being sewn.

4.Shorten stitch length is too long for the fabric.

1.The correct presser foot is not used.

2.The needle thread tension is too tight.

3.The stitch length is not suitable for the fabric being sewn.

1.Thread is caught in the hook.

2.The feed dogs are packed with lint.

Lint or oil have collected on the hook or

1. needle bar.

2.The needle is damaged. 2.Replace the needle.

3.Slight humming sound coming from internal motor.

4.Thread is caught in the hook.

5.The feed dogs are packed with lint.

1.Poor quality thread.

2.The bobbin case is threaded wrong.

3.Fabric has been pulled.

1.The machine is not turned on.

2.The Start/stop button was not pressed.

3.The presser foot lifter is raised.

The Start/stop button was pressed,

4. even through the foot controller is connected.

5.A thread is caught in the hook race.

6.The machine is not plugged in.

1.Loosen the thread tension.

2.Rethread the machine.

3.Choose a needle to suit the thread and fabric.

4.Make stitch dense.

1.Select the correct foot.

2.Loosen the thread tension .

3.Make stitch adjustment.

Remove the upper thread and bobbin case. Turn the handwheel backwards and forwards by hand and remove the thread remnants.

1.Clean the hook and feed dog as described.

3.Normal

Remove the upper thread and bobbin case. Turn the handwheel backwards and forwards by hand and remove the thread remnants.

1.Select a better quality thread.

2.Remove the bobbin case, the thread and reinsert correctly.

3.Do not pull on the fabric while sewing, let it be taken up by the machine.

1.Turn on the machine.

2.Press the Start/stop button.

3.Lower the presser foot lifter.

4.Do not use Start/stop button when the foot controller is con-nected. To use Start/stop button, disconnect the foot controller.

5.Remove the upper thread and bobbin case. Turn the handwheel backwards and forwards by hand and remove the thread remnants.

6.Connect the power line plug to the electric outlet.

Correction Reference

Page 19

Page 13

Page 22

Page 27

Page 73

Page 19

Page 27

Page 69

Page 23

Page 69

Page 22

Page 12

Page 9

Page 24

Page 17

Page 24

Page 69

Page 9

72

Page 79

Page 80

Do not dispose of electrical appliances as unsorted municipal waste, use separate collection facilities.

Contact your local government for information regarding the collection systems available. If electrical appliances are disposed of in landfills or dumps, hazardous substances can leak

into the groundwater and get into the food chain, damaging your health and well-being. When replacing old appliances with new once, the retailer is legally obligated to take back your

old appliance for disposal at least for free of charge.

021H5E0102(EN)

Alfa Next 200 User guide

Specifications and Main Features

Frequently Asked Questions

User Manual

I

II

III

IV

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

25

26

27

28

29

30

31

32

33

34

35

36

37

38

39

40

41

42

4 3

44

45

46

47

48

49

50

51

52

53

54

55

56

57

58

59

60

61

62

6 3

64

65

66

67

68

69

70

71

72