HyperGuard
World leader in metal detection for anti-shoplifting purposes
Alert Hyperguard
OEM Integration guide V1.0
Phone: +45 36 46 71 71
Fax: +45 36 46 71 74
Info@alertsystems.dk
Systems
Vester Voldgade 104 st, th 1552 Copenhagen V, Denmark
www.alerthyperguard.com
HyperGuard
World leader in metal detection for anti-shoplifting purposes
TABLE OF CONTENTS
1. FORWORD ................................................................................................. 3
2. FCC / IC ...................................................................................................... 3
2.1 LABELING REQUIREMENTS ........................................................................................................ 3
2.2 FEDERAL COMMUNICATIONS COMMISSION STATEMENT ..................................................... 3
2.3 INDUSTRY CANADA STATEMENT ............................................................................................... 4
3. MODULE HYPER ANTENNA 3.1 PCB ...................................................... 5
3.1 MECHANICAL DIMMENTIONS ...................................................................................................... 5
4. HOW TO INTEGRATE THE MODULE INTO AN OEM ANTENNA ............ 6
4.1 OEM EAS ANTENNA ..................................................................................................................... 6
4.2 OEM ANTENNA ............................................................................................................................. 6
4.3 EAS ANTENNA BOARD INTEGRATION KIT ................................................................................ 7
4.4 COLOR CODE OF THE CAT5E CABLE ........................................................................................ 7
900-1003151 Alert Hyperguard OEM Integration guide V1.0-4 Page: 2/7
Date: January 14, 2015
HyperGuard
World leader in metal detection for anti-shoplifting purposes
1. FORWORD
The purpose with this guide is to give instructions for integrating the module HYPER ANTENNA 3.1 into the
antenna housing.
2. FCC / IC
2.1 Labeling requirements
The HYPER ANTENNA 3.1 module meets Part 15 of the FCC rules and regulations. Compliance with the
labeling requirements, FCC notices is required.
In order to comply with FCC Certification requirements, the Original Equipment Manufacturer (OEM) must
fulfill the following requirements.
The system integrator must place an exterior label on the outside of the final product housing the
HYPER ANTENNA 3.1 Module. The figure below shows the contents that must be included in this
label.
The OEM must make sure that FCC / IC labeling requirements are met. This includes a clearly visible exterior
label on the outside of the final product housing, that displays the contents sho wn in below:
Contains FCC ID: S8OHYPER1730
IC ID: 5849A-HGINT1730
M/N: HYPER ANTENNA 3.1
2.2 Federal Communications Commission Statement
Limited Modular Approval:
This module is approved only for installation in devices under control of the grante e and only for models
indicated in this filing. The antenna(s) used for this module must not be co-located or operated in conjunction
with any other antenna or transmitter. Separate approval is required for all other operating configurations, and
different antenna configurations.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
1. this device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired
operation of the device”
The S8OHYPER1730 module is approved only for installation into the antenna hous ing types:
Alert HyperGuard Antenna V2.0 12cm
HyperGuard Antenna V2.0 18cm
HyperGUARD V2.0 Pedestal P10.
WARNING!
The antenna(s) used for this module must not be co-located or operated in conjunction with any other antenna
or transmitter. Separate approval is required for all other operating configurations, and different ante nna
configurations”.
Changes or modifications not expressly approved by the party responsible for compliance could void
the user's authority to operate the equipment
900-1003151 Alert Hyperguard OEM Integration guide V1.0-4 Page: 3/7
Date: January 14, 2015
HyperGuard
World leader in metal detection for anti-shoplifting purposes
2.3 Industry Canada Statement
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the
following two conditions: (1) this device may not cause interference, and (2) this device must accept any
interference, including interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de
licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de
brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le
brouillage est susceptible d'en compromettre le fonctionnement.
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and
maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio
interference to other users, the antenna type and its gain should be so chosen that the equivalent isotrop ically
radiated power (e.i.r.p.) is not more than that necessary for successful communication.
Conformément à la réglementation d'Industrie Canada, le présent émetteur radio p eut
fonctionner avec une antenne d'un type et d'un gain maximal (ou inférie ur) approuvé pour
l'émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage radioélectrique à l'intention
des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope
rayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensité nécessaire à l'établissement d'une communication
satisfaisante.
This radio transmitter (IC: 5849A-HGINT1730) has been approved by Industry Canada to operate with the
antenna sizes listed below with the maximum permissible gain and required antenna impedance for each
antenna size indicated. Antenna sizes not included in this list, having a gain greater than the maxim um g ain
indicated for that type, are strictly prohibited for use with this device.
Le présent émetteur radio (IC: 5849A-HGINT1730) a été approuvé par Industrie Canada pour fonctionner
avec les tailles d'antenne énumérés ci-dessous et ayant un gain admissible maximal et l'impédance requise
pour chaque tailles d'antenne. Antenne tailles non inclus dans cette liste, ou dont le gain est supérieur au gain
maximal indiqué, sont strictement interdits pour l'exploitation de l'émetteur
The 5849A-HGINT1730 module is approved only for installation into the antenna housing types:
Alert HyperGuard Antenna V2.0 12cm
Alert HyperGuard Antenna V2.0 18cm
HyperGUARD V2.0 Pedestal P10.
900-1003151 Alert Hyperguard OEM Integration guide V1.0-4 Page: 4/7
Date: January 14, 2015
HyperGuard
World leader in metal detection for anti-shoplifting purposes
3. MODULE HYPER ANTENNA 3.1 PCB
Module HYPER ANTENNA 3.1 have the following FCC ID and IC ID numbers:
FCC ID: S8OHYPER1730
IC ID: 5849A-HGINT1730
Top side of Antenna board Bottom side of antenna board Label on antenna board
3.1 Mechanical dimmentions
Length: 140 mm / 5.51 in
Width: 80 mm / 3.15 in
Height: 18 mm / 0.71 in
Weight : 95 g / 0.63 oz
900-1003151 Alert Hyperguard OEM Integration guide V1.0-4 Page: 5/7
Date: January 14, 2015
HyperGuard
World leader in metal detection for anti-shoplifting purposes
4. HOW TO INTEGRATE THE MODULE INTO AN OEM ANTENNA
4.1 OEM EAS antenna
Place the module at the bottom of the EAS antenna using the parts in the board installation kit.
It is very important that the board is placed in the centerline with RJ45 connectors pointing down.
Connect the 0 loop and ground to connector P5 as shown in the drawing.
Please note:
Special concederations due to the magnetic sensor on the module
If using metal screws for fixing the module, they shall be of non ferromagnetic materials like stainless steel
4.2 OEM antenna
Place the module at the bottom of the EAS antenna using the parts in the board installation kit.
It is very important that the board is placed in the centerline with RJ45 connectors pointing down.
Connect the 0 loop to connector P5 as shown in the drawing.
The ground wire shall not be connected
Please note:
Special concederations due to the magnetic sensor on the module
If using metal screws for fixing the module, they shall be of non ferromagnetic materials like stainless steel
900-1003151 Alert Hyperguard OEM Integration guide V1.0-4 Page: 6/7
Date: January 14, 2015
HyperGuard
World leader in metal detection for anti-shoplifting purposes
4.3 EAS antenna board integration kit
The RF antenna board integration kit consists of
4 pcb spacers with adhesive
4 pcb stand offs
Alcohol swab for cleaning metal surfaces where the spacers shall be placed
an extension cable consisting of three wires.
Two wires to the zero loop
One wire to the ground (see drawing above)
2.5 m / CAT5e cable terminated in one end with RJ45 connector
2 x RJ45 connector
4.4 Color code of the CAT5e cable
Color code and the CAT5e cable
Wiring: EIA/TIA-568B
Article number: 9001003151
900-1003151 Alert Hyperguard OEM Integration guide V1.0-4 Page: 7/7
Date: January 14, 2015
Loading...