Package Components
5
14
ALEKO
12
13
Preparation
1. Open the package and check all parts and accessories on the package
components. Insure nothing is missing in the package box.
2. Prepare the installation tools, like electric hand drill, hand plier, measuring tape,
screwdriver, an erasable color pen ect.
3. Please take a look bellow drawing, there are 4 points need to be fixed on your c
aravan, those 4 points defer in distance (height and width of each type are
different) Please find it in the bellow measurement sheet of the type you bought.
Then calculate and measure right installation points, Mark it with erasable color
pen.
( A )
Min.
1.75m
1
2
3
4
5
6
7
8
9
10
11
12
13
14
Fabric lock rail
Fabric tube
Left arm
Right arm
Upper bracket
Bottom bracket
Pull rod
Peg
M6x50 hex head screw
Φ4.1x35 Self-tapping screw
Φ4.1x13.5 Self-tapping screw
M6x16 screw
Set screw
Fabric tube connector
ATTENTION
Our awning min.folded arm height is 1.75m. if your
caravan is high, please extend the arm to suit for your
caravan. Then lock the position with our set screw.
set screw
Metric measurement
( A )
A+0.08
A-0.13
A-0.254
A+0.105
1.75
2.5
Imperial system measurement
ALEKO
Awning width(A)
5.12
REMAKE:
A,represent awning width.
Please check above measurement sheet carefully, and calculate the correct installation
position accordingly.
step 1
Find out the awning brackets(2pcs bottom brackets + 2pcs upper brackets which
already fixed on the arm) and two arms. see package components pic. 5 and 6.
step 2
Drill the holes according to your marked positions.
(You may check again the right distance of the upper and bottom brackets)
ATTENTION
Please insure all brackets positions are free stable and DO NOT overlap with other
parts of the caravan side wall (Eg.Windows, doors or others).
Φ4.2x35
Φ4.2x13.5
65mm
Please insure the arms are vertical to the
ground and parallel to each other !
The fabric lock rail is
between two upper
brackets,but keep
them in the same
height position.
Find the self tapping
screws then fix the
fabric on each side of
fabric lock rail, in case
of fabric slide out when
operating the awning.
Fabric lock rail
M6x50
Fix the bottom
brackets with M10
screws.
M6x50
Fix the upper
brackets with M10
screws.
Install the LED strip
There is a groove for Led Strip which is under
the fabric groove on the fabric lock rail. See
pic You can slid your LED strip into it if you
have.
(But the Led strip is not our standard
accessories.if you need,please kindly contact
with our salesman to order it)
Led strip groove
ALEKO
Step 8
Please kindly remove the right side end cap from fabric tube and then take out the springs.
Then put the fabric into fabric tube according to below steps.
If you choose a modular type ,
please connect the fabric tube first.
Connect the fabric tube
A
A
M6x16 screw
A
B
B
B
Poly cord
Poly cord
When reset the side cover components, Make sure the
triangle block at the right position Or, the spring is very
easy to waggle, and can't work stable !
1) Find the poly cord and get across
fabric loop.
2) Put the fabric into the fabric tube
groove.
3) Put the fabric into second fabric
tube groove, then get the poly
cord across.
4) Put the pull strap on the last tube.
Pull strap
Right
B
A
Triangle block
Put the triangle block
into Red marked
groove !
B
Left
Put the triangle block into
Red marked groove !
P.9
Step.9
Connect the right arm
1.Turn down the Safety-spring lock according to the PIC marked direction
(On and ONLY the RIGHT side of the fabric tube,there is a Safety-spring lock)
2.Make Pre-stress for right side spring by turn the sping ending stick with
clamp/screw driver fully turn 15 turns according to pic marked diretion
3.Connect the tube with arm,see pic
ALEKO
Connect the left arm
1.Make Pre-stress for Left side sping by turn the sping ending stick with screw
driver/clamp fully turn 15 turns accoring to pic marked direction
2.After doing the pre-stressing,please DO NOT LOOSE the clamp/screw,until
the left arm is connected safely
ATTENTION
By now,installation step is done,please double check the
awning and keep awning twoside spring tension are the sa
me,and in a state of equilibrium.
Step.10 Step.11
Turn up the safety-spring lock according the
pic marked direction
Pull to close the awning.
P.10
P.11
Open steps
Step.1 Step.2
Release the inner and outer arm-lock
each side.
Open
Turndown thespringlockaccordingthepic.
markeddirection.
ALEKO
Step.7
Release the outer arms from their
bottom brackets by pushing the little
lever.
Take care that the construction won't be
twisted too much doing so. You may
post the outer arms in a good 90 degree
angle to the ground. Now adjust the
necessary height and then fix the tubes
with their locks.
Step.8
Fix the bottom plates of the poles with the
steel-peg. That way the outer arms become
the poles of the awning .
Step.3
Grab the pull strap with the pull rod.
Now pull the construction open until
the outside arms are parallel to the
ground.
Pull to open
Step.5
Keep the pull strap nicely by pulling it
on one end of the fabric-tube and wrap
the strap around the arm.
Step.4
Open the wheel-lock of the inside arms and
move the arms to the end of the
fabric-tube. Then tighten their wheel-locks
each side.
Wheel-lock
Step.6
Now you can lift up the arm by opening
the handle-lock on the outer arms and
stretch them as long as you like (ranging
from1.75 to 2.87m).
Handle-lock
Press
Close steps
Step.1
Pull out the pegs from the
bottom-plate of the outer
arms.
Pull out
α
Outer arms / polesThere should
be a little inclination of the fabric
against the ground in order to let
rain-water run down from the
fabric !
Step.2
Lift up the outer arms and pull them
back into their bottom-bracket on the
caravan sidewall by opening the
bottom-bracket-locks.
Press
P.12
Step2
Step1
P.13
Close steps
Step.3 Step.4
ALEKO
AWNING CARE AND MAINTENANCE CARE
Open
Step2
Press the buttons inside the outer
arms and now slide the two tubes of
the inner arm into each other.
Now open the
handle-lock
and slide the
two tubes of
the outer arms
into another.
Press
button
Step.7
Grab the pull strap and put it in the
middle of the fabric-tube and then pull
the awning slightly,then let the awning
rolls itself up slowly.
Turn the
wheel-lock.
Step.6Step.5
Turnup thesafety springlockaccording
thepic markeddirection.
Step.8
Close the inner and outer arm-lock
each side.
Regularly check if the awning fasteners keep tight , if not, please tight all
fasteners. And Periodically clean the awning fabric and arms.
HOW TO CLEAN FABRIC
Monthly flush off the awning fabric with clean water and thorough cleaning
the fabric with soft brush and warm water every one or two years.
PLEASE NOTE
When you clean the fabric , only the natural soap and clean water.
Never detergent, old based cleaners or any caustic, granulated or
abrasive type cleaners.
Air- dry, Roll up the awning until the fabric is dry thoroughly.
HOW TO CLEAN AWNING ARMS
Regularly wash out the arm channels with hose off water in case of dirt
and debris cause the arm channels not to slide easily. It is better if you
can lightly spray the inside of the channel with dry silicone lubricant.
To clean the arms periodically, it is the best way to keep the awning arms
and braces operating smoothly.
After the arms have been cleaned and dried thoroughly, open the arm
locks, then sprayed with dry lubricant to prevent binding and locking
Pull to close
Completely
closed
Lock
ATTENTION
Please make sure that all parts of the awnings are safely locked when you are not
using it!
P.14
P.15
Loading...