Page 1
ASSEMBLY INSTRUCTIONS
Description
:5 DRAWER CHEST RTA
Printed in Vietnam
- 1 -
Page 2
BEFORE ASSEMBLY
Thank you for purchasing this quality product. This product has been designed for easy assembly and
constructed for durability. All parts were checked prior to packaging to insure quality. Prior to
beginning assembly, however, make sure all parts and hardware are included and free of obvious
defect. If a part is missing or defective, please contact the store where purchased.
IMPORTANT NOTE:
- Place all wooden parts on a clean and smooth surface such as a rug or carpet to avoid the
parts from being scratched.
- Remove all wrapping material, including staples & packing straps before you start to assemble.
- DO NOT tighten all screws and bolts until completely assembled.
- Keep all hardware parts out of reach of children.
WARNING:
Long exposure to rubber or soft plastic may cause a chemical reaction and damage the finish
of your product. Protect the surface of the product with cloth if you are using any product
with rubber feet or base.
ASSEMBLY TOOLS REQUIRED
NOT INCLUDED
- 2 -
Printed in Vietnam
Page 3
PART LIST
When unpacking, please be careful not to discard any parts with the packaging. Before continuing,
please make sure you have the following parts:
NO Description Qty Sketch NO Description Qty Sketch
B
Side panel
2 (L-
R)
A
Top
1
C
Back rail
E
G
I
Bottom panel
Drawer front
Drawer back
1
2
5
5
D
F
H
J
Center panel
Back panel
Drawer side
Drawer bottom
1
3
10
(L-R)
5
K
Support bar
5
- 3 -
Printed in Vietnam
Page 4
HARDWARE LIST
When unpacking, please be careful not to discard any parts with the packaging. Before continuing,
please make sure you have all of the following hardware:
NO Description Qty Sketch NO Description Qty Sketch
1
3
5
7
9
11
Allen key
(M4x80mm)
Spring washer
(6.5x11mm)
(M4 X 35mm)
(30x30mm)
Steel band 1
(M3 X 15mm)
Screw
Knob
Screw
12
65
10
1
2
2
4
6
8
10
Bolt
(M6 X 30mm)
Flat Washer
(6.5x13mm)
Pan head
screw
(M4 x 30mm)
Screw
(M4 X 30mm)
Warning label 5
12
12
10
10
- 4 -
Printed in Vietnam
Page 5
STEP 1
Attach top (A), center panel (D), and bottom panel (C) to a side panel (B) with bolts (2) and washers
(3) and (4) .Tighten with Allen key (1).
Slide back panel (F), and back rail (E) into the groove as shown below.
STEP 2
Attach bottom panel (C), center panel (D), and top (A) to the other side panel (B) with bolts (2), and
washers (3) and (4) .Tighten with Allen key (1).
Printed in Vietnam
- 5 -
Page 6
STEP 3
Attach back rail (E) to side panels (B) with screws (5) .Tighten with a screwdriver.
Attach the steel band (9) to Chest with screws (11) as shown below.
STEP 4
Attach drawer sides (H) to drawer front (G) with screws (5). Tighten with a screwdriver
Insert drawer bottom (J) into the grooves at bottom of drawer sides (H), and drawer front (G) as shown
below.
- 6 -
Printed in Vietnam
Page 7
STEP 5
Attach drawer back (I) to drawer sides (H) with screws (5) as shown below. Tighten with a screwdriver.
STEP 6
Attach support bars (K) to bottom of drawers with screws (8) as shown below. Tighten with the
screwdriver.
- 7 -
Printed in Vietnam
Page 8
STEP 7
Attach knobs (7) to front of drawers with screws (6). Tighten with the screwdriver.
Stick the warning labels (10) inside the drawers before use
STEP 8
Attach the steel band (9) to the wall with screws (5) as shown below (to secure the product and
prevent tipping).
- 8 -
Printed in Vietnam
Loading...