Page 1
Introduction
Thank you for your purchase. Our solar charged lighting eliminates the problems associated
with most solar lighting available today. Our solar charged lights are brighter and last all
night with a typical solar charge. Unique design, superior light output and numerous
installation options confirm the outstanding value of our product.
The company also offers unique products from multi-purpose solar lamps to emergency
lighting products.
For technical assistance and more information call our Toll Free number or visit our
website.
Please read the instruction manual carefully to obtain the best results from your purchase.
Tools that are needed but not supplied with the solar post lamps are: a screw driver and a
power drill.
Page 2
2
D
1. Solar Lamp Location:
For optimum light duration throughout the night, it is very important to place your solar
lamp in a spot where it will receive the maximum amount of direct sunlight throughout the
day.
NOTE: For best results, the solar lamp post must be charged for two sunny days in the “ON”
position.
2. Assembly instructions
NOTE: The following steps are for reference only. Consult your local hardware store
for the best installation method for your surface.
Assembly Instructions:
1. Slide the finial Part (A) on top of Part (B), secure it with the set screw
using the provided Allen wrench.
each other
6. Screw the fitter adapter Part (E) into the pole Part (D)
7. Slide Part (C) on top of Part (E), secure it with the set screw using the
provided Allen wrench.
Fig.1
A
B C E
F
WARNING: These Light bulbs are built and designed for our products only. They are not
designed to be used in other electrical sockets.
For the same reason, regular AC and/or Low Voltage bulbs cannot be used in our
products.
2. Install Solar LED Light Bulb into Part (B)
3. Attach Part (B) to Part (C) and secure it with the provided screws and nuts
4. Screw the pole Part (D) into the base Part (F)
5. Screw the additional two poles Part (D) to
Page 3
3
1. Detach the top of the lamp unit (B) by releasing the 3 screws.
Make sure the Low/OFF/High switch is in the OFF (O) position.
2. Remove (if needed) the existing bulb by turning it
counterclockwise.
clockwise (Fig.2).
4. Reassemble the unit by reversing the above procedure
3. Operation Instructions (Fig. 3)
1. Remove the final Part (A) from Part (B). Turn the
operation switch to the Low or High position (Fig.3)
according your preferences:
a. (Low) For softer light and longer duration.
b. (High) For brighter light output.
2. The solar lamp will automatically operate at dusk.
3. Re-Install the final Part (A) on top of Part (B).
4. Replacing the Battery
(After several years of use, the battery may need replacing.)
1. Unscrew the three screw caps and detach the top (B).
2. Make sure the ON/OFF switch is in the OFF (O) position.
3. Unscrew the battery compartment (Fig.4)
located on the silver reflector and remove the
compartment door.
3.2V/1,500mAh, Li-ion Rechargeable
Battery with a connector.
6. Clip on the new battery and install it into the battery
compartment. Re-Install the battery compartment cover.
7. Reattach the top and secure it with the three screw caps.
Fig.3
Fig.2
Fig.4
NOTE: When installing the Solar LED Bulb, hold it
from its silver base not by the glass
Solar LED Light Bulb Assembly
The Solar LED Bulb is designed to last up to 10 years, however if it
doesn’t work, or if you want to use different color temperature bulb, it
can be easily replaced.
3. Install the new Solar LED Bulb by turning into the bulb socket
4. Unclip the connector and remove the old battery.
5. Make sure the new battery is
Page 4
4
WARNING: Do not dispose of Li-On battery in the regular trash, municipal waste
stream or by fire as batteries may leak or explode. Do not open, short circuit, or
mutilate batteries as injury may occur. Preserve our environment by recycling Li-Ion
batteries or disposing of them in accordance with local, State and federal
regulations. Do not mix old and new batteries.
Maintenance
Clean the solar module regularly with a damp towel to guarantee optimum
performance of the solar panel. Do not use any type of solvent for cleaning and be
careful not to put too much pressure on the module while cleaning.
Trouble Shooting
If your solar charged light does not come on at dusk despite observance of all the
instructions, please try the following steps:
1. Make sure that the solar light is not being affected by any other light
source.
2. Ensure the solar light is not positioned in the shade during the day.
3. Make sure the switch in the lamp head is in NOT on the” OFF”
NOTE: The performance of the solar light will vary with the time of year. It will
deliver more light when it has had a full day in the sun rather than a day in overcast
weather.
WINTERTIME TIPS: Keep snow and debris cleaned off the solar panels so the
batteries can recharge. If the lights are covered with snow for an extended period of
time, after the snow melts, allow all the batteries to charge in full, direct sunlight for
at least 6 hours to their maximum capacity.
WARNING: Please keep out of reach of children.
** Our batteries are available at our website
Make sure the new battery is 3.2V/1,500mAh, Li-ion
Rechargeable Battery with a connector.
** Our Bulbs are available at our website
Make sure the new bulb you purchase is compatible with this model (A50 bulb)
position.
4. Check that the batteries are installed correctly.
5. Check that the Solar LED Light Bulb is installed correctly.
Loading...