C
E
H
G
F
A
B
D
I
G
White or
HOUSE
Black
WIRES
(Hot)
Smooth
FIXTURE
WIRES
Black or
Ribbed
WIRES
FIXTURE
Bare Copper(Ground)
FIXTURE
WIRES
Copper
(Ground)
HOUSE
(Neutral)
WIRES
White
Bare
Green or
WIRES
HOUSE
Listed
U
L
R
INSTALLA TIONINSTRUCTIONS
WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER .
ASSEMBLING
ASSEMBLING
ASSEMBLING
ASSEMBLING THE
THE
FIXTURE
THE
FIXTURE
THE FIXTURE
FIXTURE (
(
Fig.
(
Fig.
( Fig.
Fig. 2)
2)
.
2)
.
2) .
.
1. Return the arms to suitable position ， see figure.2.
2. Attach the pipe nipple ( D ) to top center coupling of fixture body ( G ) by
turning it clockwise until tight , then slide the column(C) and cover(B)
over end pipe nipple of the fixture body,lock them whit the hex nut(I),
attach the loop(A) to the end pipe nipple by turning it clockwise
until tight.
3. Attach the ball ( H ) to bottom center coupling of the fixture body( G ) by
turning it clockwise until tight.
4. Slide the cover( F ) onto the lamp holder ,slide the candle sleeve( E )
over the lamp holder.
5. Install the light bulbs in accordance with the fixture specifications
NOTE:
NOTE:
NOTE:
NOTE: DO
HANGING
HANGING
HANGING
HANGING THE
DO
NOT
DO
DO NOT
THE
THE
THE FIXTURE
EXCEED
NOT
EXCEED
NOT EXCEED
EXCEED THE
FIXTURE
FIXTURE
FIXTURE (
THE
SPECIFIED
THE
SPECIFIED
THE SPECIFIED
SPECIFIED WATTAGE!
(
Fig.
1)
(
Fig.
1)
( Fig.
Fig. 1)
1)
WATTAGE!
WATTAGE!
WATTAGE!
1. Shut off the power at the circuit breaker and remove old fixture
from ceiling, including the old single bar.
2. Carefully unpack new fixture and lay all the parts on a clear
surface.
3. Thread nipple (C) into loop (F) until snug.
4. Thread other end of nipple (C) with loop attached into single bar
(D) until snug.
5. Place lock washer (B) over end of nipple protruding t hrough single
bar and thread hex nut (A) onto nipple until tight.
6. Take this single bar assembly and mount to ceiling junction box
with junction box screws (E). Tighten screws securely with
screwdriver .
7. Us ing proper chain pliers to open one end link of the chain
provided and connect to the fixture loop (I). Close the link .
8. By measuring, determine correct number of links needed for
proper hanging height. Using proper chain pliers disconnect and
discard remaining chain.
9. Lace the fixture wires through the chain.
10. Slip loop collar (H) over the chain, then do the same with the
canopy (G).
11. Open the other end link of the chain and hang the f ixture on the
loop at the ceiling. Close the link.
12. Feed the fixture wires through the loop (F) and nipple (C) and pull
until taut.
13. Slide canopy (G) up flush to ceiling, secure using loop (H).
CONNECTING
CONNECTING
CONNECTING
CONNECTING THE
1. Take the black wire from the ceiling junction box and the smooth
THE
THE
THE WIRES
wire leg from the fixture and twist bare ends together. Twist wire
connector onto end of wire until snug.
2. Repeat same process with white junction box wire and ribbed wire
leg of fixture wire. NOTE: Twist wires together in the same
direction you twist the wire connector onto wires.
3. If your junction box has a grounding wire (green or bare copper),
attach this wire and the bare copper wire from the fixture together
as step 1.If junction box has no ground wire, attach the bare copper
WIRES
WIRES
WIRES (
(
Fig.
(
Fig.
( Fig.
Fig. 3)
3)
3)
3)
fixture wire to the green ground screw on the single bar.
4. Tuck these wire connections nea t ly into the ceiling outlet box and
then raise the canopy (G) all the way to the ceiling. Raise the loop
(H) and thread onto ceiling loop protruding through canopy
Your
Your
Your
Your
box
box
box
box and
installation
installation
installation
installation is
and
test
and
test
and test
test the
is
is
is now
the
fixture.
the
fixture.
the fixture.
fixture.
now
complete.
now
complete.
now complete.
complete. Return
Return
Return
Return power
power
power
power to
to
the
to
the
to the
the junction
junction
junction
junction
Fig. 1
Fig. 2
Fig. 3
Loading...