Page 1
NOTE : This Bed is NOT a TOY.
Keep your child / children at bay during the assembly process.
The BED is HEAVY.
To prevent injury to yourself or damage to the product a minimum of two adults are
required whenever moving or lifting the product.
Queen Size Bed
CAUTION: You must read this before you proceed.
1 OF 11
Page 2
No. Picture Description Qty
A Headboard 1
B Headboard Panel 1
C Headboard Left Foot 1
D Headboard Right Foot 1
E
Side Panel
2
F Footboard 1
G
Cross Slat With
Mounting Positions
3
H
Cross Slat Without
Mounting Positions
8
I Vertical Slat 1
J
Support Foot for Vertical
Slat
3
2 OF 11
Page 3
K Footboard Foot 2
L
Left Wing
1
M Right Wing
1
No. Picture Description Qty
①
Bolt (M8X50mm)
15
②
Bolt (M8X60mm)
3
③
Spring Washer
17
④
Washer
17
⑤
Allen Key
1
⑥
Screw
(2cm self-tapping)
2
⑦
Screw
(5cm Self Tapping)
2
⑧
Metal Bracket
4
⑨
Restraint Strap
2
⑩
Screwdriver
Not Provided
Before Beginning Assembly:
3 OF 11
Page 4
Unpack
and place
all parts for
clear
visibility.
Pack A:
Hardware
for
assembly
of Bed.
Bolt(①)
Bolt(②)
Spring Washer(③)
Washer(④)
Allen Key(⑤)
Screw(⑥)
Screw(⑦)
Metal Bracket(⑧)
Restraint Strap(⑨)
OVERVIEW
This Bed has multiple parts and may require up to 60 minutes to assemble. To give you an overview of the Bed
parts, the above picture is to help you put the various Bed parts into perspective. Please read through the
instructions below to familiarise yourself with the parts and steps before assembly.
Right Wing(H)
Headboard(A)
Left Wing (L)
Headboard Panel(B)
Headboard
Left Foot(C)
Headboard Right Foot(D)
Side Panel(E)
Side Panel(E)
Footboard(F)
Vertical Slat(I)
Support Foot For Vertical
Slat(J)
Footboard Foot(K)
Cross Slat Without Mounting Position(H)
Cross Slat With
Mounting Position(G)
Cross Slat With Mounting
Position(G)
4 OF 11
Page 5
Step 1
Remove Headbord Left Foot(C), Headbord Right Foot(D), Left Wing(L), and Right Wing(M) from the carton.
Align Left Wing(L) to the Headboard(A) on the mounting position ,then attach using Bolts(①), Spring
Washers(③) and Washers(④) with Allen Key(⑤).
Attach Right Wing (M) to Headboard(A) using Bolts(①), Spring Washers(③) and Washers(④) with Allen
Key(⑤).
Tighten the Bolts fully in a sequential manner.
Step 2
Step 3
3.1
3.2
③
④
①
⑤
5 OF 11
Page 6
Step 4
Attach Side Panel(E) to Headboad Left Foot(C) and Headboad Right Foot(D) by sliding the iron plates onto the
Bolts as shown.
Attach Footboard Foot(K) to Footboard(F) by inserting the threaded stem of the Foot and turning clockwise until
secure.
The bulge from the Leg should face inside when finished.
Step 5
3.1) Place the Headboard(A), Headboard Panel(B), Headboard Left Foot(C) and Headboard Right Foot(D) into
position as shown.
3.2) Attach the Headboard Left Foot(C) and Headboard Right Foot(D) to Headboard(A) using Bolts(①), Spring
Washers(③), and Washers(④) with Allen Key(⑤).
Then, attach the Headboard Left Foot(C) and Headboard Right Foot(D) to Headboard Panel(B) using Bolts(①),
Spring Washers(③), and Washers(④) with Allen Key(⑤).
Tighten the Bolts fully in a sequential manner.
K
6 OF 11
Page 7
Attach Side Panel(E) to Left Wing(L) using Bolts(①), Spring Washers(③), and Washers(④) with Allen Key(⑤).
Attach Side Panel(E) to Right Wing(M) using Bolts(①), Spring Washers(③), and Washers(④) with Allen
Key(⑤).
Tighten the Bolts fully in a sequential manner.
Attach Side Panel(E) to Footboard(F) by sliding the Metal Plates onto the Bolts as shown.
First insert the Metal Plate, then press it down lightly.
The Side Panel(E) should rest on the Footboard Foot(K).
Step 6
Step 7
Headboard Wing
7 OF 11
Page 8
8.1) Place the Vertical Slat(I) with “Face up" label down.
8.2) Attach Support Foot for Vertical Slat(J) to the bottom of Vertical Slat(I) by inserting the
threaded stem in the Foot and turning clockwise until secure.
8.3) Stand the Vertical Slat upright.
Step 9
9.1
9.2
Step 8
8.1
8.2
8.3
I
Labelled "Face Up"
Labelled "Face Up"
I
J
I
J
G
E
①
④
⑤
8 OF 11
Page 9
Put the Cross Slats(H) into the grooves of the Side Rails(E).
9.1) Put the Cross Slats(G) into the grooves of the Side Panel(E).
9.2) Attach Vertical Slat(I) to the bottom of Cross Slats(G) using Bolts(①) and Washers(④) with Allen Key(⑤).
Tighten Bolts until fully secure in a sequential manner.
Heardboard Restraint Device Installation Instruction
Step 11
Ensure that all Bolts are secured at all joints.
Your Bed is ready for use.
This Bed can only be used on a flat, level surface.
WARNING
Serious or fatal crushing injuries can occur from tipping furniture. To help prevent tip-over:
ALWAYS secure this furniture to the wall using a Safety Restraint Device. See product
instructions for more ways to help prevent furniture tip-over.
Step 10
H
E
9 OF 11
Page 10
Put the Headboard against the wall where desired and mark the location for the Metal Brackets(⑧) to be the
same height as the top of the Headboard.
Attach Metal Bracket(⑧) to the wall where you marked using Screws(⑦) with Screwdriver(⑩).
Repeat this process with the other Metal Bracket(⑧).
Note: The Metal Brackets need to be secured to solid, load bearing surface. Please use a Stud
Finder(not supplied) if needed to locate the Wall Frame.
Move the Headboard back against wall.
Pull the Restraint Straps(⑨) through the Metal Brackets(⑧) on the wall and Headboard(A) one by one, and pull
the Restraint Straps(⑨) tight.
The strap between Headboard and Metal Brackets on wall should be within 3.5''.
Locate the two marks on Headboard(A).
Then, Attach the Metal Brackets(⑧) to the back of Headboard(A) using Screws(⑥) with Screwdriver(⑩) as
shown above.
Tighten Screws until firm and secure.
⑥
⑦
⑥
⑦
⑨
⑧
⑧
⑥
⑦
Metal Bracket on
the back side of
Headboard
Metal Bracket on the wall
Within 3.5''
10 OF 11
Page 11
11 OF 11
Loading...