ASSEMBLING
ASSEMBLING
ASSEMBLING
ASSEMBLING &
&
INSTALLATION
&
INSTALLATION
& INSTALLATION
INSTALLATION INSTRUCTIONS
INSTRUCTIONS
INSTRUCTIONS
INSTRUCTIONS
WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER .
ASSEMBLING
ASSEMBLING
ASSEMBLING
ASSEMBLING THE
1. Return the arms to suitable position, see figure.2.
2. Attach the loop (A) to the fixture body ( D
tight.
3 . Raise the pipe nipple (F) into the bottom plate of fixture body(D) and
lock it securely with finial(E) , a ttach the cover ( G ) to end of the pipe
nipple, lock it securely with finial ( H ).
4 . Attach the glass shade ( C ) on to the lamp holder , then lock it securely
w ith check ring ( B ).
5 . Install the light bulbs in accordance with the fixture specifications
NOTE: DO NOT EXCEED THE SPECIFIED
HANGING
HANGING
HANGING
HANGING THE
1. Shut off the power at the circuit breaker and remove old fixture
from ceiling, including the old single bar.
2. Carefully unpack new fixture and lay all the parts on a clear
surface.
3. Thread nipple (C) into loop (F) until snug.
4. Thread other end of nipple (C) with loop attached into single bar
(D) until snug.
5. Place lock washer (B) over end of nipple protruding t hrough single
bar and thread hex nut (A) onto nipple until tight.
6. Take this single bar assembly and mount to ceiling junction box
with junction box screws (E). Tighten screws securely with
screwdriver .
7. Us ing proper chain pliers to open one end link of the chain
provided and connect to the fixture loop (I). Close the link .
8. By measuring, determine correct number of links needed for
proper hanging height. Using proper chain pliers disconnect and
discard remaining chain.
9. Lace the fixture wires through the chain.
10. Slip loop collar (H) over the chain, then do the same with the
canopy (G).
11. Open the other end link of the chain and hang the f ixture on the
loop at the ceiling. Close the link.
12. Feed the fixture wires through the loop (F) and nipple (C) and pull
until taut.
13. Slide canopy (G) up flush to ceiling, secure using loop (H).
CONNECTING
CONNECTING
CONNECTING
CONNECTING THE
1. Take the black wire from the ceiling junction box and the smooth
wire leg from the fixture and twist bare ends together. Twist wire
connector onto end of wire until snug.
2. Repeat same process with white junction box wire and ribbed wire
leg of fixture wire. NOTE: Twist wires together in the same
direction you twist the wire connector onto wires.
3. If your junction box has a grounding wire (green or bare copper),
attach this wire and the bare copper wire from the fixture together
as step 1.If junction box has no ground wire, attach the bare copper
fixture wire to the green ground screw on the single bar.
4. Tuck these wire connections nea t ly into the ceiling outlet box and
then raise the canopy (G) all the way to the ceiling. Raise the loop
(H) and thread onto ceiling loop protruding through canopy .
Your
Your
Your
Your
junction
junction
junction
junction box
THE
THE
THE FIXTURE
THE
FIXTURE
THE
FIXTURE
THE FIXTURE
FIXTURE (
THE
THE
THE WIRES
installation
installation
installation
installation is
box
and
box
and
box and
and test
FIXTURE
FIXTURE
FIXTURE (
(
Fig.
(
Fig.
( Fig.
Fig. 1)
WIRES
WIRES
WIRES (
is
now
is
now
is now
now complete.
test
the
test
test the
fixture.
the
fixture.
the fixture.
fixture.
(
Fig.
2)
.
(
Fig.
2)
.
( Fig.
Fig. 2)
2) .
.
D
D
D ) by turning it clockwise until
1)
1)
1)
(
Fig.
3)
(
Fig.
3)
( Fig.
Fig. 3)
3)
complete.
complete.
complete. Return
WATTAGE
Return
Return
Return power
!
power
power
power to
to
to
to the
the
the
the
Fig. 1
Fig. 2
A
D
E
F
G
H
Fig. 3
FIXTURE
WIRES
Black or
Smooth
HOUSE
WIRES
Black
(Hot)
FIXTURE
WIRES
White or
Ribbed
HOUSE
WIRES
White
(Neutral)
FIXTURE
WIRES
Bare
Copper
(Ground)
HOUSE
WIRES
Green or
Bare Copper(Ground)
U
R
Listed
L
Loading...