Albrecht BPA 300 User guide

BPA 300

Headset + Adapter for Headset Communication

to Bluetooth®- Devices

Headset + Adapter for Headset Communication to Bluetooth®- Devices

Button

ALBRECHT BPA 300 is a wireless motor bike headset
which can connect with any Bluetooth-compatible
GSM Phone, Bluetooth Navigators or Bluetooth­compatible 2-way radios or - adapters like BPA
100/200.

LED

with the adapter.

The headset can provide clear communications even
under hard conditions. Depending on the version, a
suitable helmet headset for closed helmets (article. No.

15500) or open helmets (article No. 15510) is supplied

With the B

PA 300 you can answer phone calls from
your mobile phone, listen to the voice
announcement of GPS navigators or you can
establish a Bluetooth speech connection with
transceivers having a built-in wireless adapter or
external adaptor (like BPA 100, BPA 100G, or BPA

200). You can wear it very easily within Your motor
bike clothing near to the helmet.

Main features

• Voice communication with Bluetooth Mobile Phones or Navigators – the adapter
together with the suitable helmet headset provides excellent voice quality for phone calls
and Navigator functions via Bluetooth devices.

• Start / Stop, accepting or rejecting incoming phone calls – by simple and
comfortable single-button operation

• Establishing permanent wireless connections, where necessary – important to listen
to navigator announcements transmitted into the helmet or listening to PMR 446 radio
channels via Bluetooth- compatible adaptors.

• Extends an already built-in wired helmet headset for wireless communication

• The adapter is using the latest Bluetooth protocol version and has Bluetooth V 2.00

CSR chipset. It works like a headset protocol adapter and lets the device appear in
other “master” Bluetooth devices like GSM phones or navigators as a “slave” headset.

Precautions

The adaptor should not be used in the close neighbourhood or with direct mechanical contact
to other transmitting devices – interferences or operation errors might occur.

The adapter can be charged from the 230 V power network or via special DC charging adaptor
cable (optional available under order No. 15403) from the 12 V motor bike board network.

The manufacturer is not responsible for any radio or TV interference caused by unauthorized
modification to this equipment; such modifications could void the users authority to use this
equipment

etting ready

G
Charging the wireless adapter

Completely charge the internal Lithium Polymer battery for at least 2- max.4 hours before using
the set for the first time. Insert the DC charging plug of the wall charger into the adapter and
connect the wall charger to an AC outlet. The LED will be red during charging and will be off
after charging is completed. The charging process will be automatically terminated at full
battery condition, so over-charging is not possible. Please do not use any other wall charger
than the supplied charger. Other chargers may not support the automatic charge termination at
the end of the charging process and may cause severe problems and fire or injury risks
through burning or exploding batteries.

When the battery is running low during operation, the LED indicator will flash . When the
low power alert is displayed, you will have approximately 10 minutes of talk time remaining
before the battery runs out completely.

The battery can be charged anytime without the need of full discharging. Be sure to charge the
headset at room temperature. The battery may not be properly charged if the temperature is
too high or too low.
After unplugging the headset from the charger, please avoid placing the set in locations of high
temperature or direct sunlight, i.e. above the gas tank of a motorcycle or under the windshield
of a car.
I Please do not attempt to replace the battery of the adapter set. The battery is soldered and
can only be replaced by authorized service partners.
You may answer an incoming call only if the battery has sufficient power while charging.

Connecting the adapter with the wired headset

ou can plug the 6 pin male plug of the wired helmet set into the 6 pin female plug of the

Y
adapter. The helmet set can be ALBRECHT CHS 300, OHS 500, OHS 550. Other headsets
like MHS 300 or MHS 301 headsets can be connected only if already equipped with 6 pin male
plugs. MIDLAND Headsets like MA 46 and other brands do not fit, even if they may use the
same connector type!

Turning the adapter set on and off
Turning on the adapter:

• Press and hold the button for approximately 3 sec. until the LED will flash 3 x green