AKiTiO NT2 U3 User Manual [en, de, es, fr]
2-Bay RAID Storage Enclosure
NT2 U3
User Manual
ES
FR
DE
EN
August 2, 2011 – v1.0
NT2 U3 Introduction
1 Introduction
1.1 System Requirements
1.1.1 PC Requirements
• Minimum Intel Pentium III CPU 500MHz, 128MB RAM
• Windows Vista, Windows 7
• Your hardware device must have the correct corresponding port (e.g. USB 3.0 host controller)
1.1.2 Mac Requirements
• Minimum Apple G4 processor, 128MB RAM
• Mac OS 10.4 or above
• Your hardware device must have the correct corresponding port (e.g. USB 2.0 host controller)
Note
USB 3.0 is not available for the Mac except with a special PCI card that comes with a USB 3.0
driver for Mac OS. However, it is possible to use the drive with the slower USB 2.0 connection.
1.1.3 Supported Hard Drives
• One or two 3.5" SATA-I, SATA-II or SATA-III hard drives
• 80GB - 3TB per HDD
• Hard drives of identical capacities are recommended
• Supports large volumes in excess of 2TB
Note
In order for the computer to access volumes larger than 2TB, both the hardware and OS need
to have the capacity to support large volumes (e.g. Windows 7 or Mac OS 10.4 and above).
1.2 Package Contents
Package content may vary depending on vendor & version.
• NT2 storage enclosure (hard drives not included)
• Power supply
• Interface cable
• User manual
1.3 About this Manual
Firmware, images and descriptions may vary slightly between this manual and the actual product
you have. Functions and features may change depending on the firmware version.
1.4 Trademarks
• MS-DOS, Microsoft, Windows Vista & 7 are trademarks of Microsoft Corporation.
• Apple Macintosh and Mac are trademarks of Apple Computer.
• All other third party brands and names are the property of their respective owners.
[1]
NT2 U3 Introduction
LED
Status
Blinking fast (125ms on/off) = Rebuilding RAID 1 array
DIP Switch
RAID Mode
. Make sure to
Fan
Confirm RAID mode
RAID switch
Kensington security slot
USB 3.0 port
Power switch
Power receptacle
1.5 Detailed View
Front View Rear View
1.5.1 LED indication
HDD
A & B
Note
In order to determine which type of blinking the LED indicates, stop transferring files to or from
the hard drives. The slow blinking will be slower and the fast blinking will be faster than the
usual flashing of the LED during data access.
1.5.2 RAID switch
• Blue = Power on
• Green = Status OK, USB connection to computer is established
• OFF = Empty drive bay or USB connection is not yet established
• Flashing Green = Data access (read/write)
• Blinking slow (500ms on/off) = Drive failure (error)
•
Non-RAID
Switch position: 1 OFF, 2 OFF
RAID 0 - Striping
Switch position: 1 ON, 2 OFF
RAID 1 - Mirroring
Switch position: 1 OFF, 2 ON
Changing the RAID mode
requires formatting the
drives
backup all existing data
first!
Note
Except for the Non-RAID mode, two hard drives are required. After changing the RAID mode,
press the button above the RAID switch to confirm the new setting.
[2]
NT2 U3 Introduction
1.6 RAID Modes
For RAID 0/1, hard drives of identical capacities are recommended. If the capacities are different,
the total amount of the space that can be used will depend on the drive with the smallest capacity.
1.6.1 Non-RAID
The drives show up as independent volumes. Each drive can be formatted and accessed
separately. If one drive fails, the other is not affected. This setting does not provide any
performance or redundancy benefits.
1 or 2 drives
1.6.2 RAID 0 - Disk Striping
The drives are shown as one large single volume but the total size will depend on the drive with the
smallest capacity. This setting is used where speed is the primary objective but RAID Level 0 (also
called striping) is not redundant. This form of array splits each piece of data across the drives in
segments; since data is written without any form of parity data-checking, it allows for the fastest
data transfer of all other modes. On the downside, if one drive becomes damaged, the whole array
can become corrupted.
2 drives
1.6.3 RAID 1 - Disk Mirroring
Two drives show up as one volume but only 50% of the total capacity, depending on the drive with
the smallest capacity, can be used. RAID 1 creates an exact copy (or mirror) of a set of data on the
second drive. This is useful when reliability and backup take precedence over storage capacity.
Should one hard drive fail, it can be replaced and the data rebuilt automatically.
2 drives
Note
In order for the computer to access volumes larger than 2TB, both the hardware and OS need
to have the capacity to support large volumes (e.g. Windows 7 or Mac OS 10.4 and above).
1.6.4 Changing the RAID Mode
The RAID mode should be set after installing and before formatting the drives.
1. Install the hard drives.
2. Turn on the power.
3. Set the RAID switch and select your preferred RAID mode.
4. Press the button above the RAID switch to confirm the current setting.
5. Format the drives.
6. Done.
Note
Changing the RAID mode requires formatting the drives. Make sure to backup all existing data
first!
[3]
NT2 U3 System Setup
2 System Setup
2.1 Hard Drive Assembly
The drives can be installed at any position, there is no specific order required.
1. Unlock the switch at the bottom of the case and lift the front panel upward and away from
the housing to remove it.
2. Install the hard drives as illustrated below with the top of the drives, where the label is
located, facing each other. Push the drives lightly into place and then replace the front
panel.
3. Connect the device to your computer and turn on the power.
4. Set your preferred RAID mode and confirm it by pushing the button above the RAID switch.
5. For PC users, use the disk management tool or for Mac users, use the disk utility to create
a new partition and format the drives.
6. Done! Your external drive is now ready to use.
Note
Be careful not to damage any components, and do not force the drives into place. If they not
easily slide into place and fit, make sure the drives have been installed correctly. The top of
the drives, where the label is located, should face each other.
2.1.1 Installing a HDD with existing data and setting up a RAID 1 array
1. Set the RAID mode to RAID 1.
2. Install the drive with the existing data into slot A and then turn on the power.
3. Press the “Confirm RAID mode” button and then make sure the computer has recognized
your hard drive and you can access the data.
4. Install the second (blank) drive in slot B and let it rebuild the RAID 1 array. Make sure the
capacity of the HDD in slot B is equal or larger than the capacity of the HDD in slot A!
[4]
NT2 U3 System Setup
2.2 Replacing Hard Drives
When a drive fails, the corresponding HDD LED (A or B) will be blinking slowly, unless the RAID
mode is set to Non-RAID, in which case the HDD will simply not be accessible anymore.
If only one drive is defective and the RAID mode is set to RAID 1, the data can still be accessed
but we strongly recommend replacing the faulty drive immediately to assure continued proper
backup and data safety.
If more than one drive at the same time fails or if the RAID mode is set to RAID 0, the data will be
lost and the system can not be accessed again until the drive(s) have been replaced.
2.2.1 Non-RAID
1. Check the HDD LED. The corresponding LED for the defective drive will be blinking slowly.
2. Turn off the power and replace the faulty drive(s).
3. Turn on the power. The corresponding LED will turn a steady green again.
4. Format the new drive(s).
2.2.2 RAID 0
1. Check the HDD LED. The corresponding LED for the defective drive will be blinking slowly.
2. Turn off the power and replace the faulty drive(s).
3. Turn on the power. The corresponding LED will turn a steady green again.
4. Push the button above the RAID switch to confirm the current RAID mode.
5. Format the drive.
2.2.3 RAID 1
1. Check the HDD LED. The corresponding LED for the defective drive will be blinking slowly.
2. Turn off the power and remove the faulty drive.
3. Make sure the USB cable is plugged in and connected to your computer.
4. Turn on the power and wait for about 30 seconds for the system to start up.
5. Install the new hard drive.
6. The LED of the source drive will start to blink rapidly and the LED of the destination drive
will start to blink slowly. This indicates that it is now rebuilding the RAID array.
7. Rebuilding the RAID array will take several hours, depending on the drive capacity. When
the data has been restored, the LEDs will turn a steady green.
Note
We recommend not turning off the power during the rebuild process but if the process is
interrupted, it will continue rebuilding the data as soon as the power is turned back on.
[5]
NT2 U3 System Setup
2.3 Connection to Computer
A few precautions and notes when using your external storage drive:
• Do not expose the product to water or humid conditions.
• Do not cover the enclosure’s ventilation holes.
• Before connecting the device, install the hard drives and set your preferred RAID mode.
• For the safe removal of your drive and to assure that no data is lost, always follow the correct
unplug procedure for external hardware (e.g. Eject the drive before removal).
• In order for the computer to access volumes larger than 2TB, both the hardware and Operating
System need to have the capacity to support large volumes (e.g.: Windows Vista, Windows 7 or
Mac OS 10.4 and above).
• When the computer goes into stand-by mode, the hard drives in the external enclosure will spin
down as well.
2.4 Precautions
2.4.1 Power on/off precautions
It is highly recommended to switch the unit off when not in use. When re-locating the device or
when not in use for an extended period of time, we strongly recommend unplugging the unit.
2.4.2 Location and placing precautions
Avoid positioning your device in the following places:
• Locations with direct sunlight, next to radiators, other sources of heat.
• Locations with very high temperatures (more than 38° C) or humidity (more than 90%).
• Very dusty or sandy locations.
• Locations subject to vibration, shock, or with a sloping base.
2.4.3 Electricity and power plug
Careful attention must be paid to the following points in order to prevent damage, fire, and/or injury:
• When removing the power cable from the socket, pull on the plug fixture and never on the cord.
• Do not connect and remove the power cable with wet hands.
• Keep the power cable away from heaters.
• Never try to repair the power cable yourself or to modify it in any way.
• If the unit is dropped or becomes damaged in any other way, unplug the power cable.
2.4.4 Cables
Use only the cables supplied or recommended by your vendor in order to avoid the risk of
malfunction, electric shock, and/or possible interference to the device.
2.5 About Data Backup
To protect your files and help prevent the loss of your data, we strongly recommend that you keep
two copies of your data, one copy on your NT2 and a second copy either on your internal drive or
another storage media such as CD, DVD, Tape or an additional external drive.
Any loss or corruption of data while using the NT2 is the sole responsibility of the user, and under
no circumstances will the manufacturer be held liable for compensation or the recovery of this data.
[6]
NT2 U3 Appendix
Application
80GB - 3TB
Interface/Ports
USB 3.0 SuperSpeed
Data Transfer
• USB 3.0 up to 5Gbps (625MB/s)
USB 2.0 up to 480Mbps (60MB/s)
System Requirements
(e.g. USB 3.0, USB 2.0 or PCI card)
Operating Environment
Humidity: 20%RH ~ 80%RH
Storage Environment
Humidity: 10%RH ~ 90%RH
Power Supply
• Input: AC 100-240V
Output: DC +12V/3A
Product Size
7in x 4.8in x 3.2in
3 Appendix
3.1 Specifications
• 3.5” SATA-I, SATA-II or SATA-III hard drives
• 1.5Gb/s or 3.0Gb/s
•
•
•
• PC: Windows Vista or Windows 7
• Mac: Mac OS 10.4 or above
• Your hardware device must have the correct corresponding port
• Temperature: 5°C ~ 40°C
•
• Temperature: -20°C ~ 70°C
•
•
• 17.7cm x 12.3cm x 8.1cm
•
3.2 FAQ
Q: Can I connect this device to a USB 2.0 host?
A: Yes, this device is backwards compatible with USB 2.0.
Q: What file system should I choose to format my drive?
A: This will depend on how you want to use the drive but in general, we recommend:
• Windows Vista/7 NTFS
• Mac OS X HFS+ (Mac OS Extended)
• To use it on both PC and Mac FAT32 (single file size is limited to 4GB)
Q: How many drives can fail before I lose my data?
A: For RAID 0, any drive failure will result in the data being lost. For RAID 1, more than one drive
failure at the same time will mean the data can not be recovered anymore. For Non-RAID, only the
data on the defective drive will be lost.
© Copyright 2011 by AKiTiO - All Rights Reserved
The information contained in this manual is believed to be accurate and reliable. AKiTiO assumes no responsibility for
any errors contained in this manual. AKiTiO reserves the right to make changes in the specifications and/or design of this
product without prior notice. The diagrams contained in this manual may also not fully represent the product that you are
using and are there for illustration purposes only. AKiTiO assumes no responsibility for any differences between the
product mentioned in this manual and the product you may have.
[7]
Bedienungsanleitung
ES
FR
DE
EN
RAID-Speichergehäuse mit zwei Einschüben
NT2 U3
2. August 2011 - v1.0
NT2 U3 Einleitung
1 Einleitung
1.1 Systemanforderungen
1.1.1 PC-Anforderungen
• Mindestens Intel Pentium III-CPU mit 500 MHz, 128 MB RAM
• Windows Vista, Windows 7
• Ihr Computer muss über den entsprechenden Anschluss verfügen (z. B. USB 3.0-Host-
Controller)
1.1.2 Mac-Anforderungen
• Mindestens Apple G4-Prozessor, 128 MB RAM
• Mac OS 10.4 oder aktueller
• Ihr Computer muss über den entsprechenden Anschluss verfügen (z. B. USB 2.0-Host-
Controller)
Hinweis
USB 3.0 ist nicht erhältlich für den Mac ausser mit einer speziellen PCI-Steckkarte welche mit
einem USB 3.0-Treiber für den Mac geliefert wird. Es ist jedoch möglich das Gerät mit der
langsamen USB 2.0 Verbindung zu verwenden.
1.1.3 Unterstützte Festplatten
• Ein oder zwei 3,5-Zoll-SATA-I, SATA-II- oder SATA-III-Festplatten
• 80 GB - 3TB pro HDD
• Es werden Festplatten mit identischen Kapazitäten empfohlen
• Unterstützt große Laufwerke mit mehr als 2 TB
Hinweis
Damit der Computer auf Laufwerke mit mehr als 2 TB zugreifen kann, müssen sowohl die
Hardware als auch das Betriebssystem über die Kapazität zur Unterstützung großer
Laufwerke verfügen (z. B.: Windows 7 oder Mac OS 10.4 und aktueller).
1.2 Lieferumfang
Der Lieferumfang kann je nach Verkäufer & Version variieren.
• NT2-Speichergehäuse (ohne Festplatten)
• Netzteil
• Schnittstellenkabel
• Handbuch
1.3 Über dieses Handbuch
Firmware, Bilder und Beschreibungen in diesem Handbuch können leicht von dem tatsächlichen
Produkt abweichen. Funktionen und Merkmale können sich in Abhängigkeit an die FirmwareVersion ändern.
1.4 Marken
• MS-DOS, Microsoft, Windows XP/Vista/7 sind Marken der Microsoft Corporation.
• Apple Macintosh und Mac sind Marken von Apple Computer.
• Alle anderen Marken und Namen Dritter sind Eigentum ihrer jeweiligen Inhaber.
[1]
Loading...