AKG Acoustics C 2000 B User Manual

C 2000 B

Stage and Studio Condenser Microphone

Description

The C 2000 B is a versatile, side-address cardioid condenser
microphone intended for professional and home studio
applications as well as on-stage activities. It consists of a patent
pending one-half inch capsule element which is placed in a
larger baffle ring. This measure gives the C 2000 B more
forward directionality at high frequencies. The microphone’s
response is tailored to have a broad on-axis rise at high
frequencies, while maintaining a fairly uniform diffuse field over
the entire frequency band. The added presence at very high
frequencies is an asset in many micing situations, especially
home recording studios, while maintaining good feedback
rejection in live sound applications.

Its 0.5% THD point of 140 dB (150 dB with the integral 10-dB
pad engaged) and high sensitivity of 20 mV/Pa indicate that this
model can deliver maximum operating output signals in the
range of 4 volts. The self-noise floor is 20 dB (A), giving the
microphone an effective dynamic range of 120 dB. An integral
bass cut switch provides a gentle 6 dB per octave roll-off below
500 Hz, and as such will compensate for the proximity effect
(low frequency boost) associated with close micing.

The cardioid polar pattern, has been refined to give maximum
rejection across the frequency band at 180 degrees. Internal
shock mounting of the diaphragm assembly makes this model
studio friendly and easy to use in demanding live performances.
The SA41/1 stand adapter is included. Optional accessories
include the B18E battery supply unit and the H 100 external
elastic shock suspension.

Features

• Wide dynamic range of 120 dB

• Transformerless output for ultra
low LF distortion

• Frequency response shaped for
studio applications and highest
gain before feedback

• Pre-attenuation (-10 dB)

• Bass roll-off provided (6dB/octave
below 500Hz)

• Dedicated cardioid polar pattern

Specifications

Transducer type: Prepolarized condenser

Frequency response: 30 Hz to 20 kHz

Sensitivity at 1 kHz: 20 mV/Pa (-34 dBV)

Polar pattern: Cardioid

Pre-attenuation: 10 dB

Bass cut filter: 6 dB/octave below 500 Hz

Impedance: 200 ohms

Recommended loading: >1000 ohms

Equivalent noise level (A-weighted): 20 dB

Sound pressure level for 0.5% THD:

140 dB (150 dB with 10 dB pre-attenuation)

S/N ratio (A-weighted): 74 dB

Power requirement: Phantom powering, 9 to 52 Vdc

Current consumption: <2 mA

Output connector: 3-pin XLR-M

Finish: champagne

Size: 2.1 in. diameter (53 mm);

6.3 in. length (159 mm)

Net/shipping weight: 11.5 oz. (325 g)/2.1 lb. (950 g)

Included accessories: SA 41 stand mount

Optional accessories: B 18 E battery power supply

H 100 elastic shock suspension

Microphones · Headphones · Wireless Microphones · Wireless Headphones · Headsets · Electroacoustical Components

Limited Warranty

Valid only in the United States. AKG Acoustics warrants AKG products against defects in material
or workmanship for a period of three years from the date of original purchase for use, and agrees
to repair or, at our option, replace any defective unit without charge for either parts or labor.
Important: This warranty does not cover damage resulting from accident, misuse or abuse, lack of
reasonable care, the affixing of any attachment not provided with the product, loss of parts or
connecting the product to any but the specified receptacles. This warranty is void unless service
or repairs are performed by an authorized service center. No responsibility is assumed for any

special, incidental or consequential damages. However, the limitation of any right or remedy shall
not be effective where such is prohibited or restricted by law. Simply take or ship your AKG product
prepaid to our service department. Be sure to include your sales slip as proof of purchase date.
(We will not repair transit damage under the no-charge terms of this warranty.) Note: No other
warranty, written or oral is authorized by AKG Acoustics, Inc. This warranty gives you specific legal
rights, and you may also have other rights which vary from state to state. Some states do not allow
the exclusion or limitation of incidental or consequential damages or limitation on how long an
implied warranty lasts, so the above exclusions and limitation may not apply to you.

Specifications subject to change without notice.

AKG Acoustics GmbH

Lemböckgasse 21–25, P.O.B. 158, A-1230
Vienna/AUSTRIA
Tel: [phone]*, Fax: [phone]
Internet: http://www.akg.com

AKG Acoustics; A Division of Harman Pro Germany
Bodenseestraße 228, D-81243 München/GERMANY
Tel: [phone], Fax: [phone]

Arbiter Pro Audio

Wilberforce Road, London NW9 6AX/ENGLAND
Tel: [phone], Fax: [phone]

AKG ACOUSTICS, U.S.

914 Airpark Center Drive
Nashville, TN 37217, U.S.A.
Tel: [phone], Fax: [phone]

Studer Japan Ltd.

2-43-7, Uehara, Shibuya-ku, Tokyo 151-0064/JAPAN
Tel: [phone], Fax: [phone]

Erikson Pro Audio

620 McCaffrey, St-Laurent, Quebec, H4T 1N1, CANADA
Tel: [phone], Fax: [phone]
Internet: www.jam-ind.com/eriksonpro

AKG is constantly improving and modifying its products, therefore, specifications are subject to change without notice.

The microphone shall be a 0.5-inch diameter condenser model
with a single dedicated cardioid pickup pattern. The microphone’s
sensitivity shall be no less than 20 mV/Pa. The microphone’s
equivalent noise level shall be no greater than 20-dB (A), and at an
operating level of 140 dB the microphone’s total harmonic
distortion shall be no greater than 0.5%. The microphone shall
include a pre-attenuation switch of 10-dB and a bass roll-off switch

of 6 dB per octave commencing at 500 Hz. The microphone shall
operate with phantom power over the range from 9 Vdc to 52 Vdc.
The microphone shall have a diameter no greater than 2.1 in. (53
mm) and a length no greater than 6.3 in. (159 mm). The net weight
of the microphone shall be no greater than 11.5 oz. The
microphone shall be the AKG Acoustics Model C 2000 B.

Graphical Data

Architects and Engineers Specifications

DS-C 2000 B

6.3 in.
length

2.1 in.

diameter