Aiwa Z-KD770, Z-KD970, Z-KD770, Z-KD970 Schematic

Download

Page 1

Z-KD770

Z-KD970

SERVICE MANUAL

COMPACT DISC STEREO

CASSETTE RECEIVER

CASSEIVER

Z–KD770

Z–KD970

• This Service Manual is the "Revision Publishing" and replaces "Simple Manual" Z-KD770/KD970, (S/M Code No. 09-005-434-5T1).

• If requiring information about the CD mechanism, see Service Manual of

6ZG-1, (S/M Code No. 09-001-338-7N2).

CX–ZKD770

CX–ZKD970

BASIC TAPE MECHANISM : 2ZM-3MK2 PR5NM BASIC CD MECHANISM : 6ZG-1 VZRDM

SPEAKERSYSTEM

SX–ZHT730

SX–CR677

SX–ZHT930

SX–CR677

REMOTE

CONTROLLER

RC–ZAS08

S/M Code No. 09-008-434-5R1

REVISION

DATA

Page 2

SPECIFICATIONS

FM tuner section

Tuning range 87.5 MHz to 108 MHz Usable sensitivity (IHF) 13.2 dBf Antenna terminals 75 ohms (unbalanced)

AM tuner section

Tuning range 530 kHz to 1710 kHz (10 kHz step)

531 kHz to 1602 kHz (9 kHz step)

Usable sensitivity 350 µV/m Antenna Loop antenna

Amplifier section

Power output Front

Rated: 120 W + 120 W<770> Rated: 150 W + 150 W<970> (6 ohms, T.H.D. 1 %, 1 kHz) Reference: 150 W + 150 W<770> Reference: 180 W + 180 W<970> (6 ohms, T.H.D. 10 %, 1 kHz)

Rear (Surround)

Rated: 33 W + 33 W (8 ohms, T.H.D. 1 %, 1 kHz) Reference: 40 W + 40 W (8 ohms, T.H.D. 10 %, 1 kHz)

Centre

Rated: 34 W (8 ohms, T.H.D. 1 %, 1 kHz) Reference: 40 W (8 ohms, T.H.D. 10 %, 1 kHz)

Total harmonic distortion 0.15 % (60 W, 1 kHz, 6 ohms,

DIN AUDIO/Front)

Inputs VIDEO/AUX: 310 mV

(adjustable) PHONO: 400 mV (47 kohms) MIC1, MIC2: 1.4 mV (20 kohms)

5.1CH INPUT (adjustable) FRONT: 240 mV SURROUND: 240 mV CENTER: 600 mV SUB WOOFER: 240 mV

Outputs VIDEO OUT: 1.0 Vp-p (75 ohms)

CD DIGITAL OUT (OPTICAL) SPEAKERS: accept speakers of 6 ohms or more SURROUND SPEAKERS: accept speakers of 8-16 ohms SUB WOOFER: 1V CENTER SPEAKER: accepts speakers of 8 ohms or more PHONES (stereo jack): accepts headphones of 32 ohms or more

Cassette deck section

Track format 4 tracks, 2 channels stereo Frequency response CrO2 tape: 50 Hz - 16000 Hz

Normal tape: 50 Hz - 15000 Hz

Signal-to-noise ratio 50 dB (CrO2 tape peak level,

above 400 Hz)

Recording system AC bias Heads Deck 1: Playback head x 1

Deck 2: Recording/playback/

erase head x 1

Compact disc player section

Laser Semiconductor laser (λ =780 nm) D-A converter 1 bit dual Signal-to-noise ratio 85 dB (1 kHz, 0 dB) Harmonic distortion 0.05 % (1 kHz, 0 dB) Wow and flutter Unmeasurable Video signal NTSC/PAL color format (selectable) Video data MPEG 1 Audio data MPEG 1, LAYER 2

General

Power requirements 120 V/220-230 V/240 V AC

switchable 50/60 Hz

Power consumption 245 W<770>

260 W<970>

Dimensions of main unit 360 x 395.3 x 402.3 mm (W x H x D) (141/4 x 155/8 x 157/8 in) Weight of main unit 12.8 kg (28 lbs. 4 oz)

Speaker system SX–ZHT730<770>, SX-ZHT930<970>

Cabinet type 3 way, bass reflex Speakers Woofer:

220 mm (83/4 in.) cone type Tweeter: 60 mm (23/8 in.) cone type Super tweeter: 20 mm (13/16 in.) ceramic type

Impedance 6 ohms Output sound pressure level 89 dB/W/m Dimensions (W x H x D) 260 x 495 x 314 mm

(101/4 x 191/2 x 123/8 in.)

Weight 6.3 kg (13 lbs. 14 oz.)

• Design and specifications are subject to change without notice.

• The word "BBE"and the "BBE symbol" are trademarks of BBE Sound, Inc. Under license from BBE Sound,Inc.

• Manufactured under license from Dolby Laboratories Licensing Corporation. “DOLBY”, the double-D symbol and "PRO LOGIC" are trademarks of Dolby Laboratories Licensing Corporation.

– 2 –

Page 3

PROTECTION OF EYES FROM LASER BEAM DURING SERVICING

This set employs laser. Therefore, be sure to follow carefully the instructions below when servicing.

WARNING!!

WHEN SERVICING, DO NOT APPROACH THE LASER EXIT WITH THE EYE TOO CLOSELY. IN CASE IT IS NECESSARY TO CONFIRM LASER BEAM EMISSION. BE SURE TO OBSERVE FROM A DISTANCE OF MORE THAN 30cm FROM THE SURFACE OF THE OBJECTIVE LENS ON THE OPTICAL PICK-UP BLOCK.

s Caution: Invisible laser radiation when

open and interlocks defeated avoid exposure to beam.

s Advarsel: Usynlig laserståling ved åbning,

når sikkerhedsafbrydere er ude af funktion. Undgå udsættelse for stråling.

VAROITUS!

Laiteen Käyttäminen muulla kuin tässä käyttöohjeessa mainitulla tavalla saataa altistaa käyt-täjän turvallisuusluokan 1 ylittävälle näkymättömälle lasersäteilylle.

VARNING!

Om apparaten används på annat sätt än vad som specificeras i denna bruksanvising, kan användaren utsättas för osynling laserstrålning, som överskrider gränsen för laserklass 1.

CAUTION

Use of controls or adjustments or performance of procedures other than those specified herin may result in hazardous radiation exposure.

ATTENTION

L’utillisation de commandes, réglages ou procédures autres que ceux spécifiés peut entraîner une dangereuse exposition aux radiations.

ADVARSEL

Usynlig laserståling ved åbning, når sikkerhedsafbrydereer ude af funktion. Undgå udsættelse for stråling.

This Compact Disc player is classified as a CLASS 1 LASER product. The CLASS 1 LASER PRODUCT label is located on the rear exterior.

CLASS 1 LASER PRODUCT KLASSE 1 LASER PRODUKT LUOKAN 1 LASER LAITE KLASS 1 LASER APPARAT

Precaution to replace Optical block

(KSS-213F)

Body or clothes electrostatic potential could ruin laser diode in the optical block. Be sure ground body and workbench, and use care the clothes do not touch the diode.

1) After the connection, remove solder shown in right figure.

PICK-UP Assy P.C.B

Solder

– 3 –

Page 4

NOTE ON BEFORE STARTING REPAIR

1. Forced discharge of electrolytic capacitor of power supply block

When repair is going to be attempted in the set that uses relay circuit in the power supply block, electric potential is kept charged across the electrolytic capacitors (C101, 102) even though AC power cord is removed. If repair is attempted in this condition, secondary defect can occur. In order to prevent the secondary trouble, perform the following measures before starting repair work.

Discharge procedure

1 Remove the AC power cord.

11 22

2 Connect a discharging resistor at an end of lead wire that

has clips at both ends. Connect the other end of the lead wire to metal chassis.

3 Contact the other end of the discharging resistor to the

positive (+) side (+VH) of C101. (For two seconds)

4 Contact the same end of the discharging resistor as step

3 to the negative (-) side (-VH) of C102 in the same way.

(For two seconds)

5 Check that voltage across C101 and C102 has decreased

to 1 V or less using a multimeter or an oscilloscope.

Select a discharging resistor referring to the following table.

Charging voltage (V) Discharging

(C101, 102) resistor (Ω)

25-48 100 3 87-A00-247-090

49-140 220 5 87-A00-232-090

Note: The reference numbers (C101, C102) of the electrolytic capacitors can change depending on the models. Be sure to check the

reference numbers of the charging capacitors on schematic diagram before starting the discharging work.

Rated power (W) Parts number

MAIN C.B

D101

C101 C102

Fig-1

2. Check items before exchanging the MICROCOMPUTER

Be sure to check the following items before exchanging the MICROCOMPUTER. Exchange the MICROCOMPUTER after confirming that the MICROCOMPUTER is surely defective.

2-1. Regarding the HOLD terminal of the MICROCOMPUTER

When the HOLD terminal (INPUT) of the MICROCOMPUTER is “H”, the MICROCOMPUTER is judged to be operating correctly. When this terminal is “L”, the main power cannot be turned on. Therefore, be sure to check the terminal voltage of the HOLD terminal before exchange. When the MICROCOMPUTER is not defective, the HOLD terminal can also go “L” when the POWER AMPLIFIER has any abnormalities that triggers the abnormality detection circuit on the MAIN C. B. that sets the HOLD terminal to “L”.

• Good or no good judgement of the MICROCOMPUTER

1 Turn on the AC main power.

11 22

2 Confirm that the main power is turned on and the HOLD terminal of the MICROCOMPUTER keeps the “H” level or not.

22 33

3 When the HOLD terminal is “L” level, the abnormality detection circuit is judged to be working correctly and the

MICROCOMPUTER is judged to be good.

– 4 –

Page 5

In such a case, check also if the POWER AMPLIFIER circuit or power supply circuit has any abnormalities or not.

2-2. Regarding reset

There are cases that the machine does not work correctly because the MICROCOMPUTER is not reset even though the AC power cord is re-inserted, or the software reset (pressing the STOP key + POWER key) is performed. When the above described phenomenon occurs, it can lead to wrong judgement as if the MICROCOMPUTER is defective and to exchange the MICROCOMPUTER. In such a case, perform the forced-reset by the following procedure and check good or no good of the MICROCOMPUTER.

1 Remove the AC power cord.

FRONT C.B

MICROCOMPUTER

FRONT C.B

2 Short both ends of the electrolytic capacitor C113 that is connected to VDD of the MICROCOMPUTER with tweezers.

22 33

3 Connect the AC power cord again. If the MICROCOMPUTER returns to the normal operation, the MICROCOMPUTER is

good.

Note: The reference number or MICROCOMPUTER pin number of transistor (Q110) and electrolytic capacitor (C113) can change depending

on the models. Be sure to check the reference numbers on schematic diagram before starting the discharging work.

C113

Short with tweezers.

Fig-2-2

C113

VSS

VDD

MICROCOMPUTER

2-3. Confirmation of soldering state of MICROCOMPUTER

Check the soldering state of the MICROCOMPUTER in addition to the above described procedures. Be sure to exchange the MICROCOMPUTER after surely confirming that the trouble is not caused by poor soldering but the MICROCOMPUTER itself.

– 5 –

Page 6

ELECTRICAL MAIN PARTS LIST

PART NO. DESCRIPTIONREF. NO. KANRI

NO.

87-A21-397-010 IC,STK490-070 87-A21-021-040 C-IC,BU2099FV 87-A20-783-040 C-IC,BA7762AFS 87-A21-577-040 C-IC,M61506FP 87-A21-097-040 C-IC,M62463AFP

87-A21-482-010 IC,RPM6938-H4 87-A21-015-040 C-IC,M62491FP 87-A21-452-030 C-IC,BD3876KS2 87-A21-560-010 IC,LA1844L-A 8A-MG3-656-010 C-IC,LC876580W-5R55

87-070-127-110 IC,LC72131 D 87-070-289-040 C-IC,BU2092F 87-020-454-010 IC,DN6851 87-A20-561-040 C-IC,M65847AFP 87-A21-051-040 C-IC,BU9990-03FS

TRANSISTOR

87-026-609-080 TR,KTA1266GR 87-026-610-080 TR,KTC3198GR 87-A30-076-080 C-TR,2SC3052F 87-A30-075-080 C-TR,2SA1235F 87-A30-318-080 TR,CSA952K

87-A30-218-080 TR,2SB1237Q 87-A30-097-010 TR,FN1016<770> 87-A30-098-010 TR,FP1016<770> 87-A30-204-010 TR,2SD2439<970> 87-A30-205-010 TR,2SB1588<970>

87-A30-186-010 FET,2SK3053 89-213-702-010 TR,2SB1370E 87-A30-107-070 C-TR,CMBT5401 87-026-245-080 TR,DTC114ES 87-A30-198-080 TR,KTC3199GR

87-A30-484-080 C-TR,KRA102S 87-A30-257-080 C-TR,2SD1306E 87-A30-087-080 C-FET,2SK2158 87-A30-468-080 C-TR,KRC102S-RTK 87-A30-106-040 C-TR,CMBT5551

87-A30-190-080 TR,CC5551 87-A30-256-010 TR,2SD1933 87-A30-255-010 TR,2SB1342 87-A30-074-080 C-TR,RT1P 141C 87-A30-329-080 TR,CD1585BC

87-A30-063-080 C-TR,KRA104S 89-327-143-080 TR,2SC2714O 87-A30-489-080 C-TR,KRA107S 87-A30-234-080 TR,CSC4115BC 87-026-463-080 TR,2SA933SRS

DIODE

87-020-465-080 DIODE,1SS133 87-A40-673-090 DIODE,D10XB20 87-A40-553-080 DIODE,1N4003 LES 87-A40-780-080 ZENER,UZ33BSD 87-A40-764-080 ZENER,UZ10BSC

87-A40-313-080 C-DIODE,MC 2840 87-A40-455-080 DIODE,RL203 GM 87-A40-646-010 DIODE,FMB-G16L 87-A40-270-080 C-DIODE,MC2838 87-A40-269-080 C-DIODE,MC2836

87-A40-768-080 ZENER,UZ16BSA 87-017-447-010 DIODE,GBU4DL-6419 87-017-931-080 ZENER,MTZJ5.6B 87-017-154-080 ZENER,HZS6C3L 87-020-331-080 CHIP-DIODE,DAN202K

87-017-654-060 DIODE,GBU6JL-6131<770> 87-A40-224-060 DIODE,GBU8D<970> 87-A40-488-080 DIODE,1SS244

DESCRIPTIONREF. NO. KANRI

PART NO.

NO.

87-A40-751-080 ZENER,UZ6.2BSB 87-A40-760-080 ZENER,UZ9.1BSA 87-A40-747-080 ZENER,UZ5.1BSB 87-A40-438-080 ZENER,MTZJ4.7A 87-017-149-080 ZENER,HZS6A2L

87-A40-749-080 ZENER,UZ5.6BSB

MAIN C.B

C3 87-A10-712-080 C-CAP,S 0.22-50 Z F C4 87-A10-712-080 C-CAP,S 0.22-50 Z F C21 87-016-035-090 CAP,E 6800-35 M VR C22 87-016-035-090 CAP,E 6800-35 M VR C25 87-016-300-080 CAP, ELECT 22-100

C26 87-016-300-080 CAP, ELECT 22-100 C27 87-016-300-080 CAP, ELECT 22-100 C28 87-016-300-080 CAP, ELECT 22-100 C31 87-010-263-080 CAP, ELECT 100-10V C32 87-010-197-080 CAP, CHIP 0.01 DM

C34 87-010-247-080 CAP, ELECT 100-50V C35 87-010-406-080 CAP, ELECT 22-50V C36 87-010-381-080 CAP, ELECT 330-16V C38 87-010-394-080 CAP, ELECT 220-35V C39 87-010-394-080 CAP, ELECT 220-35V

C40 87-010-197-080 CAP, CHIP 0.01 DM C60 87-010-403-080 CAP, ELECT 3.3-50V C80 87-010-401-080 CAP, ELECT 1-50V C81 87-010-374-080 CAP, ELECT 47-10V C82 87-010-380-080 CAP, ELECT 47-16V

C115 87-010-405-080 CAP, ELECT 10-50V C116 87-010-405-080 CAP, ELECT 10-50V C117 87-010-196-080 CHIP CAPACITOR,0.1-25 C160 87-010-196-080 CHIP CAPACITOR,0.1-25 C171 87-012-368-080 C-CAP,S 0.1-50 F

C172 87-012-368-080 C-CAP,S 0.1-50 F C173 87-012-368-080 C-CAP,S 0.1-50 F C174 87-012-368-080 C-CAP,S 0.1-50 F C301 87-010-318-080 C-CAP,S 47P-50 CH C302 87-010-318-080 C-CAP,S 47P-50 CH

C303 87-012-157-080 C-CAP,S 330P-50 CH C304 87-012-157-080 C-CAP,S 330P-50 CH C305 87-012-157-080 C-CAP,S 330P-50 CH C306 87-012-157-080 C-CAP,S 330P-50 CH C307 87-010-196-080 CHIP CAPACITOR,0.1-25

C309 87-010-196-080 C-CAP,S 0.1-25 ZF C310 87-010-196-080 CHIP CAPACITOR,0.1-25 C311 87-010-198-080 CAP, CHIP 0.022 C312 87-010-198-080 CAP, CHIP 0.022 C313 87-010-178-080 C-CAP,S 1000P-50KB

C314 87-010-178-080 C-CAP,S 1000P-50KB C315 87-010-178-080 C-CAP,S 1000P-50KB C316 87-010-178-080 C-CAP,S 1000P-50KB C321 87-012-142-080 CAP, S 0.33-16 C322 87-012-142-080 CAP, S 0.33-16

C324 87-010-260-080 CAP, ELECT 47-25V C325 87-010-370-080 CAP,E 330-6.3 SME C327 87-010-404-080 CAP, ELECT 4.7-50V C328 87-010-404-080 CAP, ELECT 4.7-50V C332 87-010-196-080 CHIP CAPACITOR,0.1-25

C335 87-010-401-080 CAP, ELECT 1-50V C336 87-010-401-080 CAP, ELECT 1-50V C337 87-010-196-080 CHIP CAPACITOR,0.1-25 C339 87-010-196-080 CHIP CAPACITOR,0.1-25 C340 87-010-196-080 CHIP CAPACITOR,0.1-25

C351 87-012-140-080 CAP 470P C352 87-012-140-080 CAP 470P C354 87-010-175-080 CAP 560P C355 87-010-178-080 CHIP CAP 1000P C356 87-010-260-080 CAP, ELECT 47-25V

– 6 –

Page 7

PART NO. DESCRIPTIONREF. NO. KANRI

NO.

C357 87-010-197-080 CAP, CHIP 0.01 DM C358 87-010-183-080 C-CAP,S 2700P-50 B C359 87-010-183-080 C-CAP,S 2700P-50 B C360 87-010-183-080 C-CAP,S 2700P-50 B C370 87-010-196-080 CHIP CAPACITOR,0.1-25

C373 87-A11-177-080 C-CAP,S 0.15-16 K B C374 87-A11-177-080 C-CAP,S 0.15-16 K B C378 87-010-196-080 CHIP CAPACITOR,0.1-25 C379 87-010-406-080 CAP, ELECT 22-50 C380 87-010-406-080 CAP, ELECT 22-50

C386 87-010-196-080 CHIP CAPACITOR,0.1-25 C388 87-012-156-080 C-CAP,S 220P-50 CH C391 87-010-319-080 C-CAP,S 56P-50 CH C392 87-010-319-080 C-CAP,S 56P-50 CH C393 87-010-319-080 C-CAP,S 56P-50 CH

C394 87-010-319-080 C-CAP,S 56P-50 CH C401 87-010-176-080 C-CAP,S 680P-50 SL C402 87-010-176-080 C-CAP,S 680P-50 SL C403 87-010-958-080 CHIP -CAP,S 0.01-25BJ C404 87-010-958-080 CHIP -CAP,S 0.01-25BJ

C405 87-010-958-080 CHIP -CAP,S 0.01-25BJ C406 87-010-958-080 CHIP -CAP,S 0.01-25BJ C407 87-010-401-080 CAP, ELECT 1-50V C408 87-010-401-080 CAP, ELECT 1-50V C409 87-010-196-080 CHIP CAPACITOR,0.1-25

C410 87-010-384-080 CAP, ELECT 100-25V C411 87-010-402-080 CAP, ELECT 2.2-50V C412 87-010-402-080 CAP, ELECT 2.2-50V C413 87-010-401-080 CAP, ELECT 1-50V C414 87-010-401-080 CAP, ELECT 1-50V

C415 87-010-546-080 CAP, ELECT 0.33-50V C416 87-010-546-080 CAP, ELECT 0.33-50V C417 87-010-221-080 CAP, ELECT 470-10V C418 87-A10-891-080 CAP,E 4.7-25 SME(K) C419 87-A10-800-080 C-CAP,S 6800P-16 J B CM

C420 87-010-374-080 CAP, ELECT 47-10V C421 87-010-196-080 CHIP CAPACITOR,0.1-25 C422 87-A10-804-080 C-CAP,S 0.1-25 J B C423 87-010-374-080 CAP, ELECT 47-10V C424 87-010-374-080 CAP, ELECT 47-10V

C425 87-010-196-080 CHIP CAPACITOR,0.1-25 C430 87-012-142-080 CAP, S 0.33-16 C431 87-010-971-080 C-CAP,S 4700P-50 B J C432 87-010-178-080 CHIP CAP 1000P C433 87-A11-183-080 C-CAP,S 0.12-16 J B

C434 87-A11-182-080 C-CAP,S 0.27-16 J B C435 87-A11-182-080 C-CAP,S 0.27-16 J B C436 87-A11-183-080 C-CAP,S 0.12-16 J B C437 87-010-971-080 C-CAP,S 4700P-50 B J C438 87-010-178-080 CHIP CAP 1000P

C439 87-010-805-080 CAP, S 1-16 C440 87-010-401-080 CAP, ELECT 1-50V C441 87-A10-799-080 C-CAP,S 5600P-16 J B CM C442 87-A10-802-080 C-CAP,S 0.047-16 J B CM C443 87-A10-229-080 C-CAP,S 0.68-10 K W5

C444 87-016-460-080 C-CAP,S 0.22-16 B C445 87-016-460-080 C-CAP,S 0.22-16 B C446 87-010-404-080 CAP, ELECT 4.7-50V C447 87-010-404-080 CAP, ELECT 4.7-50V C448 87-016-460-080 C-CAP,S 0.22-16 B

C449 87-016-460-080 C-CAP,S 0.22-16 B C450 87-016-081-080 C-CAP,S 0.1-16 RK C451 87-A10-802-080 C-CAP,S 0.047-16 J B CM C452 87-A10-802-080 C-CAP,S 0.047-16 J B CM C453 87-016-081-080 C-CAP,S 0.1-16 RK

C454 87-016-081-080 C-CAP,S 0.1-16 RK C455 87-A10-801-080 C-CAP,S 0.022-16 J B CM C456 87-A10-801-080 C-CAP,S 0.022-16 J B CM C457 87-016-081-080 C-CAP,S 0.1-16 RK C461 87-010-196-080 CHIP CAPACITOR,0.1-25

DESCRIPTIONREF. NO. KANRI

PART NO.

NO.

C463 87-010-196-080 CHIP CAPACITOR,0.1-25 C465 87-012-141-080 CHIP-CAPACITOR,0.22-16F C466 87-010-194-080 CAP, CHIP 0.047 C467 87-A10-201-080 C-CAP,S0.33-16 KB C468 87-A10-060-080 C-CAP,S 0.18-16 K B

C478 87-010-265-080 CAP, ELECT 33-16V C479 87-010-179-080 CAP,CHIP S B1200P C480 87-010-179-080 CAP,CHIP S B1200P C481 87-010-179-080 CAP,CHIP S B1200P C482 87-010-179-080 CAP,CHIP S B1200P

C483 87-010-265-080 CAP, ELECT 33-16V C489 87-010-402-080 CAP, ELECT 2.2-50V C491 87-010-402-080 CAP, ELECT 2.2-50V C492 87-010-402-080 CAP, ELECT 2.2-50V C531 87-010-405-080 CAP, E 10-50 M 11L SME

C532 87-010-196-080 CAP, S 0.1-25 ZF C533 87-010-196-080 CAP, S 0.1-25 ZF C534 87-012-156-080 CAP, S 220P-50 J CH GRM C535 87-010-178-080 CAP, S 1000P-50 K B C536 87-010-196-080 CAP, S 0.1-25 ZF

C541 87-010-178-080 C-CAP, S 1000P-50 K B C611 87-010-956-080 CHIP-CAP,S 0.068-25B C612 87-010-369-080 C-CAP,S 0.033-25 K B C613 87-010-190-080 S CHIP F 0.01 C614 87-016-669-080 C-CAP,S 0.1-25 K B

C616 87-010-185-080 C-CAP,S 3900P-50 K B C617 87-010-194-080 C-CAP,S 0.047-25 ZF C618 87-010-401-080 CAP, ELECT 1-50V C619 87-010-263-080 CAP, ELECT 100-10V C620 87-016-669-080 C-CAP,S 0.1-25 K B

C621 87-010-197-080 CAP, CHIP 0.01 DM C623 87-010-401-080 CAP, ELECT 1-50V C624 87-010-401-080 CAP, ELECT 1-50V C626 87-A11-590-080 C-CAP,S 0.047-16 K B C627 87-010-400-080 CAP, ELECT 0.47-50V

C628 87-010-400-080 CAP, ELECT 0.47-50V C629 87-A11-590-080 C-CAP,S 0.047-16 K B C630 87-010-383-080 CAP, ELECT 33-25 C631 87-010-185-080 C-CAP,S 3900P-50 B C632 87-010-185-080 C-CAP,S 3900P-50 B

C634 87-010-196-080 CHIP CAPACITOR,0.1-25 C635 87-A10-307-080 CAP-M 0.1-50 J C636 87-A10-307-080 CAP-M 0.1-50 J C637 87-A10-307-080 CAP-M 0.1-50 J C638 87-A10-307-080 CAP-M 0.1-50 J

C639 87-010-405-080 CAP, ELECT 10-50V C643 87-010-196-080 C-CAP,S 0.1-25 ZF C644 87-010-401-080 CAP, ELECT 1-50V C645 87-012-156-080 C-CAP, S 220P-50 J CH GRM C671 87-010-322-080 C-CAP,S 100P-50 CH

C672 87-010-322-080 C-CAP,S 100P-50 CH C673 87-010-190-080 S CHIP F 0.01 C679 87-010-196-080 CHIP CAPACITOR,0.1-25 C680 87-010-190-080 CHIP CAPACITOR,0.01-50 ZF C685 87-010-197-080 C-CAP,S 0.01-25 KB

C771 87-010-263-080 CAP, ELECT 100-10V C772 87-010-197-080 CAP, CHIP 0.01 DM C782 87-010-197-080 CAP, CHIP 0.01 DM C783 87-010-197-080 CAP, CHIP 0.01 DM C784 87-010-197-080 CAP, CHIP 0.01 DM

C785 87-010-197-080 CAP, CHIP 0.01 DM C786 87-010-197-080 CAP, CHIP 0.01 DM C788 87-010-149-080 C-CAP,S 5P-50 CH C789 87-A12-052-080 C-CAP,S 0.033-25 J B C790 87-A12-052-080 C-CAP,S 0.033-25 J B

C791 87-010-196-080 CHIP CAPACITOR,0.1-25 C792 87-010-197-080 CAP, CHIP 0.01 DM C793 87-010-404-080 CAP, ELECT 4.7-50V C795 87-010-197-080 CAP, CHIP 0.01 DMXX C796 87-010-197-080 CAP, CHIP 0.01 DM

– 7 –

Page 8

PART NO. DESCRIPTIONREF. NO. KANRI

NO.

C797 87-010-405-080 CAP, ELECT 10-50V C798 87-010-197-080 CAP, CHIP 0.01 DM C799 87-010-407-080 CAP, ELECT 33-50V C800 87-010-194-080 CAP, CHIP 0.047 C801 87-010-403-080 CAP, ELECT 3.3-50V

C802 87-010-194-080 CAP, CHIP 0.047 C803 87-010-198-080 CAP, CHIP 0.022 C804 87-010-263-080 CAP, ELECT 100-10V C807 87-010-400-080 CAP, ELECT 0.47-50V C808 87-010-401-080 CAP, ELECT 1-50V

C809 87-010-401-080 CAP, ELECT 1-50V C810 87-010-196-080 CHIP CAPACITOR,0.1-25 C811 87-010-403-080 CAP, ELECT 3.3-50V C812 87-010-403-080 CAP, ELECT 3.3-50V C814 87-010-197-080 CAP, CHIP 0.01 DM

C815 87-010-403-080 CAP, ELECT 3.3-50V C816 87-010-403-080 CAP, ELECT 3.3-50V C819 87-010-179-080 CAP,CHIP S B1200P C820 87-010-179-080 CAP,CHIP S B1200P C821 87-010-405-080 CAP, ELECT 10-50V

C823 87-010-177-080 C-CAP,S 820P-50 J SL C824 87-010-404-080 CAP, ELECT 4.7-50 M 11L SME C825 87-010-596-080 CAP, S 0.047-16 C842 87-010-197-080 CAP, CHIP 0.01 DM C844 87-010-197-080 CAP, CHIP 0.01 DM

C850 87-010-260-080 CAP, ELECT 47-25V C851 87-010-197-080 CAP, CHIP 0.01 DM C852 87-010-197-080 CAP, CHIP 0.01 DM C853 87-010-197-080 CAP, CHIP 0.01 DM C858 87-010-196-080 CHIP CAPACITOR,0.1-25

C859 87-010-196-080 CHIP CAPACITOR,0.1-25 C860 87-010-197-080 CAP, CHIP 0.01 DM C959 87-010-196-080 CHIP CAPACITOR,0.1-25 C960 87-010-196-080 CHIP CAPACITOR,0.1-25 C961 87-010-152-080 C-CAP,S 8P-50 D CH GRM

C963 87-015-785-080 CHIP CAPACITOR, 0.1FZ-25Z C971 87-010-381-080 CAP, ELECT 330-16V C972 87-010-404-080 CAP, ELECT 4.7-50V C973 87-010-197-080 CAP, CHIP 0.01 DM C974 87-010-197-080 CAP, CHIP 0.01 DM

C979 87-010-322-080 C-CAP,S 100P-50 CH C981 87-010-260-080 CAP, ELECT 47-25V C982 87-010-196-080 CHIP CAPACITOR,0.1-25 C983 87-010-197-080 CAP, CHIP 0.01 DM C984 87-010-197-080 CAP, CHIP 0.01 DM

C987 87-010-197-080 CAP, CHIP 0.01 DM C989 87-010-197-080 CAP, CHIP 0.01 DM C991 87-010-312-080 C-CAP,S 15P-50 CH C992 87-010-312-080 C-CAP,S 15P-50 CH C993 87-010-178-080 CHIP CAP 1000P

C995 87-010-178-080 CHIP CAP 1000P C997 87-010-196-080 CHIP CAPACITOR,0.1-25 C998 87-010-260-080 CAP, ELECT 47-25V C999 87-A11-155-080 CAP,TC U 0.01-16 Z F CF831 87-008-261-010 FLTR,CF SFE10.7MA5

CF832 87-008-261-010 FLTR,CF SFE10.7MA5 CN1 87-A60-996-010 CONN,13P V BLK TAC-L13X-A3 CN91 87-A60-109-010 CONN,2P V S2M-2W CN92 87-A60-109-010 CONN,2P V S2M-2W CN101 87-A60-996-010 CONN,13P V BLK TAC-L13X-A3

CN301 87-A60-620-010 CONN,3P V 2MM JMT CN351 87-A60-625-010 CONN,8P V 2MM JMT CN601 87-099-719-010 CONN,30P TYK-B(X) CN606 87-099-566-010 CONN,7P TUC-P7P-B1 CN602 87-A60-131-010 CONN,6P V FE

CNA1 8A-NF8-653-010 CONN ASSY,9P TID-A(480) CNA2 8A-MA3-640-010 CONN ASSY,3P (VM) AMA-3 CNA3 87-049-919-010 CONN,3P V WHT EH FC602 88-906-321-110 FF-CABLE, 6P 1.25 320MM FFE831 A8-8ZA-190-030 8ZA-1 FEUNM

DESCRIPTIONREF. NO. KANRI

PART NO.

NO.

J101 87-A60-483-010 JACK,DIA6.3 BLK ST W/S KM J102 87-A60-238-010 TERMINAL,SP 4P (MSC) J431 87-A61-069-010 JACK,PIN 6P R/W,R/W, O/B MSC J603 87-A60-926-010 JACK,PIN 4P R/W TC58-118 J831 87-A60-202-010 TERMINAL,ANT 4P MSP-154V-02

L101 87-A50-610-010 COIL,1UH-K L102 87-A50-610-010 COIL,1UH-K L301 87-A50-049-010 COIL,TRAP 85K(COI) L302 87-A50-049-010 COIL,TRAP 85K(COI) L351 87-007-342-010 COIL,OSC 85K BIAS

L801 87-A50-540-010 COIL,FM DET(TOK) L802 87-A91-551-010 FLTR,PCFJZH-450 L(TOK) L811 87-005-847-080 COIL,2.2UH(CECS) L832 87-005-847-080 COIL,2.2UH(CECS) L951 8A-NF8-667-010 COIL,AM PACK 4(TOK)

R161 87-A00-441-050 RES,270-1/2W J RP R162 87-A00-441-050 RES,270-1/2W J RP R163 87-A00-441-050 RES,270-1/2W J RP R164 87-A00-441-050 RES,270-1/2W J RP R391 87-010-322-080 C-CAP,S 100P-50 CH

R407 87-022-214-080 C-RES S100K-1/10WF R445 87-010-195-080 C-CAP,S 0.068-25 F R790 87-010-197-080 CAP, CHIP 0.01 DM R991 87-010-322-080 C-CAP,S 100P-50 CH R993 87-010-322-080 C-CAP,S 100P-50 CH

R995 87-010-322-080 C-CAP,S 100P-50 CH SFR351 87-A90-433-080 SFR,50K H NVZ6TLTA SFR352 87-A90-433-080 SFR,50K H NVZ6TLTA WH1 87-A90-510-010 HLDR,WIRE 2.5-9P X991 87-A70-061-010 VIB,XTAL 4.500MHZ CSA-309

MICON C.B

C101 87-010-498-040 CAP,E 10-16 GAS C102 87-010-194-080 CAP, CHIP 0.047-25 C103 87-010-194-080 CAP, CHIP 0.047-25 C105 87-A11-242-040 CAP,E 220-10 M 5L SRM C106 87-A11-242-040 CAP,E 220-10 M 5L SRM

C107 87-010-196-080 CHIP CAPACITOR,0.1-25 C111 87-016-460-080 C-CAP,S 0.22-16 K B C112 87-010-493-040 CAP,E 0.47-50 GAS C113 87-010-178-080 CHIP CAP 1000P-50 C114 87-018-209-080 CAP, TC U 0.01-50

C116 87-010-196-080 CHIP CAPACITOR,0.1-25 C117 87-010-174-080 C-CAP,S 470P-50 J SL C122 87-012-369-080 C-CAP,S 0.047-50F C123 87-010-408-040 CAP,E 47-50 SME C124 87-010-421-040 CAP,E 4.7-50 5L

C125 87-010-421-040 CAP,E 4.7-50 5L C132 87-012-156-080 C-CAP,S 220P-50 CH C133 87-010-316-080 C-CAP,S 33P-50 CH C135 87-018-209-080 CAP, TC U 0.01-50 C137 87-010-313-080 CAP, CHIP 18P-50

C138 87-010-196-080 CHIP CAPACITOR,0.1-25 C171 87-010-213-080 C-CAP,S 0.015-50 B C172 87-010-183-080 C-CAP,S 2700P-50 B C188 87-010-194-080 CAP, CHIP 0.047-25 C193 87-010-197-080 CAP, CHIP 0.01 DM

C251 87-010-196-080 CHIP CAPACITOR,0.1-25 C252 87-012-156-080 C-CAP,S 220P-50 CH C253 87-010-322-080 C-CAP,S 100P-50 CH C301 87-012-358-080 C-CAP,S 0.47-10 F Z C302 87-012-158-080 C-CAP,S 390P-50 J CH GRM

C303 87-012-358-080 C-CAP,S 0.47-10 F Z C304 87-012-358-080 C-CAP,S 0.47-10 F Z C305 87-010-196-080 CHIP CAPACITOR,0.1-25 C306 87-010-196-080 CHIP CAPACITOR,0.1-25 C310 87-010-196-080 CHIP CAPACITOR,0.1-25

C311 87-010-405-040 CAP,E 10-50 C411 87-012-157-080 C-CAP,S 330P-50 CH

– 8 –

Page 9

PART NO. DESCRIPTIONREF. NO. KANRI

NO.

C412 87-010-405-040 CAP,E 10-50 C421 87-010-197-080 CAP, CHIP 0.01-25 C422 87-010-182-080 C-CAP,S 2200P-50 B C940 87-012-145-080 CAP, CHIP S 270P-50 J CH C941 87-012-145-080 CAP, CHIP S 270P CH

C942 87-012-145-080 CAP, CHIP S 270P CH C943 87-012-145-080 CAP, CHIP S 270P CH C944 87-012-145-080 CAP, CHIP S 270P CH C945 87-012-145-080 CAP, CHIP S 270P CH C946 87-012-145-080 CAP, CHIP S 270P CH

C947 87-012-145-080 CAP, CHIP S 270P CH C948 87-012-145-080 CAP, CHIP S 270P CH C949 87-012-145-080 CAP, CHIP S 270P CH C950 87-012-145-080 CAP, CHIP S 270P CH C951 87-012-145-080 CAP, CHIP S 270P CH

C952 87-012-145-080 CAP, CHIP S 270P CH C962 87-012-155-080 C-CAP,S 180P-50 J CH GRM C963 87-010-297-080 C-CAP,S 100P-50 J CH C966 87-010-196-080 C-CAP,S 0.1-25 ZF C967 87-010-197-080 C-CAP,S 0.01-25 KB

C969 87-010-196-080 C-CAP,S 0.1-25 ZF C968 87-016-044-040 CAP,E 100-16 M 5L MA C972 87-010-182-080 C-CAP,S 2200P-50 KB C973 87-012-156-080 C-CAP,S 220P-50 J CH GRM C974 87-015-682-040 CAP,E 22-16 M 7L SRA

C975 87-010-071-040 CAP,E 1-50 M 5L SRE C976 87-010-060-040 CAP,E 100-16 M 7L SRA C977 87-010-197-080 C-CAP,S 0.01-25 KB CN101 87-099-720-010 CONN,30P TYK-B(P) CN102 87-A60-162-010 CONN,14P H FE

CN103 87-A60-168-010 CONN,20P H FE CN104 87-A60-163-010 CONN,15P H FE CN301 87-A60-156-010 CONN,8P H FE CNA105 8A-MA3-654-010 CONN ASSY,2P V 200MM FB001 87-A90-896-080 F-BEAD,035600STY7

FC102 88-914-231-110 FF-CABLE,14P 1.25 FC103 88-920-151-110 FF-CABLE,20P 1.25 FC104 88-915-151-110 FF-CABLE,15P 1.25 150MM FL101 8A-MA3-651-010 FL,BJ751GNK L101 87-A50-333-010 COIL,OSC 9.43MHZ

L961 87-A50-093-010 COIL,CLOCK OSC 5.76MHZ LED131 87-A40-317-080 LED,SLR-342VCT31 RED LED201 87-A40-496-040 LED,SLR-342PCT31 GRN LED202 87-A40-317-080 LED,SLR-342VCT31 RED LED203 87-A40-496-040 LED,SLR-342PCT31 GRN

LED205 87-A40-317-080 LED,SLR-342VCT31 RED LED206 87-A40-496-040 LED,SLR-342PCT31 GRN LED207 87-A40-317-080 LED,SLR-342VCT31 RED LED209 87-A40-496-040 LED,SLR-342PCT31 GRN LED210 87-A40-317-080 LED,SLR-342VCT31 RED

LED211 87-A40-496-040 LED,SLR-342PCT31 GRN LED212 87-A40-317-080 LED,SLR-342VCT31 RED LED213 87-A40-317-080 LED,SLR-342VCT31 RED LED214 87-A40-317-080 LED,SLR-342VCT31 RED LED231 87-A40-317-080 LED,SLR-342VCT31 RED

LED232 87-A40-317-080 LED,SLR-342VCT31 RED LED233 87-A40-496-040 LED,SLR-342PCT31 GRN LED234 87-A40-496-040 LED,SLR-342PCT31 GRN LED235 87-A40-496-040 LED,SLR-342PCT31 GRN S401 87-A90-095-080 SW,TACT EVQ11G04M

S402 87-A90-095-080 SW,TACT EVQ11G04M S403 87-A90-095-080 SW,TACT EVQ11G04M S404 87-A90-095-080 SW,TACT EVQ11G04M S405 87-A90-095-080 SW,TACT EVQ11G04M S421 87-A91-625-010 SW,RTRY EC12E24308-30MM

CNTL C.B

C602 87-010-069-040 CAP,E 0.33-50 C603 87-010-319-080 C-CAP,S 56P-50 CH

DESCRIPTIONREF. NO. KANRI

PART NO.

NO.

C604 87-010-178-080 CHIP CAP 1000P-50 C606 87-015-785-080 CHIP CAPACITOR, 0.1-25 C607 87-010-060-040 CAP,E 100-16 C611 87-010-186-080 CAP,CHIP 4700P-50 C612 87-015-699-040 CAP,E 10-50

C651 87-010-182-080 C-CAP,S 2200P-50 B C652 87-010-197-080 CAP, CHIP 0.01-25 C661 87-010-196-080 CHIP CAPACITOR,0.1-25 C662 87-010-196-080 CHIP CAPACITOR,0.1-25 C663 87-012-156-080 C-CAP,S 220P-50 CH

C664 87-012-156-080 C-CAP,S 220P-50 CH C686 87-010-196-080 CHIP CAPACITOR,0.1-25 C692 87-010-196-080 CHIP CAPACITOR,0.1-25 C846 87-010-196-080 CHIP CAPACITOR,0.1-25 CN661 87-A60-168-010 CONN,20P H FE

CNA602 8A-MA3-655-010 CONN ASSY,2P V 60MM LED671 87-A40-317-080 LED,SLR-342VCT31 RED LED672 87-A40-317-080 LED,SLR-342VCT31 RED LED673 87-A40-317-080 LED,SLR-342VCT31 RED LED674 87-A40-317-080 LED,SLR-342VCT31 RED

LED675 87-A40-317-080 LED,SLR-342VCT31 RED LED677 87-A40-317-080 LED,SLR-342VCT31 RED LED678 87-A40-317-080 LED,SLR-342VCT31 RED LED679 87-A40-317-080 LED,SLR-342VCT31 RED LED680 87-A40-619-040 LED,SLR-56PT-T31-W GRN

LED681 87-A40-619-040 LED,SLR-56PT-T31-W GRN LED682 87-A40-619-040 LED,SLR-56PT-T31-W GRN LED683 87-A40-619-040 LED,SLR-56PT-T31-W GRN LED684 87-A40-619-040 LED,SLR-56PT-T31-W GRN LED685 87-A40-619-040 LED,SLR-56PT-T31-W GRN

LED686 87-A40-678-010 LED,SELU1E10CXM BLUE-DEF LED692 87-A40-678-010 LED,SELU1E10CXM BLUE-DEF S651 87-A91-624-010 SW,RTRY EC12E1240405-20MM S805 87-A90-095-080 SW,TACT EVQ11G04M S806 87-A90-095-080 SW,TACT EVQ11G04M

S807 87-A90-095-080 SW,TACT EVQ11G04M S808 87-A90-095-080 SW,TACT EVQ11G04M S809 87-A90-095-080 SW,TACT EVQ11G04M S810 87-A90-095-080 SW,TACT EVQ11G04M S811 87-A90-095-080 SW,TACT EVQ11G04M

S812 87-A90-095-080 SW,TACT EVQ11G04M S813 87-A90-095-080 SW,TACT EVQ11G04M S814 87-A90-095-080 SW,TACT EVQ11G04M S815 87-A90-095-080 SW,TACT EVQ11G04M S816 87-A90-095-080 SW,TACT EVQ11G04M

S817 87-A90-095-080 SW,TACT EVQ11G04M S821 87-A90-095-080 SW,TACT EVQ11G04M S822 87-A90-095-080 SW,TACT EVQ11G04M S823 87-A90-095-080 SW,TACT EVQ11G04M S824 87-A90-095-080 SW,TACT EVQ11G04M

S825 87-A90-095-080 SW,TACT EVQ11G04M S826 87-A90-095-080 SW,TACT EVQ11G04M S827 87-A90-095-080 SW,TACT EVQ11G04M S828 87-A90-095-080 SW,TACT EVQ11G04M S829 87-A90-095-080 SW,TACT EVQ11G04M

S830 87-A90-095-080 SW,TACT EVQ11G04M S831 87-A90-095-080 SW,TACT EVQ11G04M S832 87-A90-095-080 SW,TACT EVQ11G04M S833 87-A90-095-080 SW,TACT EVQ11G04M S834 87-A90-095-080 SW,TACT EVQ11G04M

S835 87-A90-095-080 SW,TACT EVQ11G04M S836 87-A90-095-080 SW,TACT EVQ11G04M S837 87-A90-095-080 SW,TACT EVQ11G04M S838 87-A90-095-080 SW,TACT EVQ11G04M S842 87-A90-095-080 SW,TACT EVQ11G04M

S843 87-A90-095-080 SW,TACT EVQ11G04M S844 87-A90-095-080 SW,TACT EVQ11G04M S845 87-A90-095-080 SW,TACT EVQ11G04M S846 87-A90-095-080 SW,TACT EVQ11G04M S847 87-A90-095-080 SW,TACT EVQ11G04M

– 9 –

Page 10

PART NO. DESCRIPTIONREF. NO. KANRI

NO.

S848 87-A90-095-080 SW,TACT EVQ11G04M S849 87-A90-095-080 SW,TACT EVQ11G04M S850 87-A90-095-080 SW,TACT EVQ11G04M S851 87-A90-095-080 SW,TACT EVQ11G04M

AMP 1F C.B

C101 87-010-178-080 CHIP CAP 1000P-50 C102 87-010-178-080 CHIP CAP 1000P C103 87-010-405-080 CAP, ELECT 10-50V C104 87-010-405-080 CAP, ELECT 10-50V C105 87-010-186-080 C-CAP,S 4700P-50 K B

C106 87-010-186-080 C-CAP,S 4700P-50 K B C107 87-010-406-080 CAP, E 22-50 M 11L SME C108 87-010-404-080 CAP, ELECT 4.7-50V C111 87-010-322-080 C-CAP,S 100P-50 J CH C112 87-010-322-080 C-CAP,S 100P-50 J CH

C113 87-A10-812-080 C-CAP,S 220P-200 J CH C114 87-A10-812-080 C-CAP,S 220P-200 J CH C119 87-010-196-080 C-CAP,S 0.1-25 ZF C120 87-010-196-080 C-CAP,S 0.1-25 ZF C121 87-010-260-080 CAP, ELECT 47-25V

C122 87-010-260-080 CAP, ELECT 47-25V C173 87-010-186-080 CAP,CHIP 4700P-50 C174 87-010-186-080 CAP,CHIP 4700P-50 C215 87-012-156-080 C-CAP,S 220P-50 C265 87-010-260-080 CAP, E 47-25V M 11L SME

C402 87-010-196-080 CHIP CAPACITOR,0.1-25 C413 87-A10-119-080 CAP,E 10-100 REA C414 87-A10-119-080 CAP,E 10-100 REA C495 87-A10-812-080 C-CAP,S 220P-200 J CH C496 87-A10-812-080 C-CAP,S 220P-200 J CH

CNA102 8A-NF8-655-010 CONN ASSY,7P TID-A (250) CNA103 8A-NF8-656-010 CONN ASSY,5P TID-A 400 CON101 87-A61-011-010 CONN,13P H BLK TAC-L13P-A3 CON102 87-A61-011-010 CONN,13P H BLK TAC-L13P-A3 CON103 87-A60-058-010 CONN,10P V 9604S-10C

JW101 87-A90-896-080 F-BEAD,035600STY7 JW124 87-A90-896-080 F-BEAD,035600STY7 R161 87-A00-418-010 RES,M/F 0.15-3W J R162 87-A00-418-010 RES,M/F 0.15-3W J R165 87-A00-418-010 RES,M/F 0.15-3W J

R166 87-A00-418-010 RES,M/F 0.15-3W J TH101 87-A91-042-080 C-THMS,100K 55001 TH102 87-A91-042-080 C-THMS,100K 55001 WH102 87-A90-460-010 HLDR WIRE 2.5-7P WH103 87-A90-459-010 HLDR,WIRE 2.5-5P

AMP 2F C.B

C100 87-018-131-080 CAP,TC U 1000P-50 K B C101 87-010-178-080 CHIP CAP 1000P C102 87-010-178-080 CHIP CAP 1000P C103 87-010-405-080 CAP, ELECT 10-50V C104 87-010-405-080 CAP, ELECT 10-50V

C107 87-010-406-080 CAP, ELECT 22-50V C108 87-010-406-080 CAP, ELECT 22-50V C111 87-010-170-080 C-CAP,S 220P-50 J SL C112 87-010-170-080 C-CAP,S 220P-50 J SL C113 87-010-260-080 CAP, ELECT 47-25V

C114 87-010-260-080 CAP, ELECT 47-25V C115 87-010-405-080 CAP, ELECT 10-50V C116 87-010-405-080 CAP, ELECT 10-50V C118 87-A10-264-080 C-CAP,S 0.1-16 ZF C119 87-A10-264-080 C-CAP,S 0.1-16 ZF

C121 87-010-190-080 S CHIP F 0.01 C122 87-010-190-080 S CHIP F 0.01 C151 87-012-368-080 C-CAP,S 0.1-50 F C152 87-012-368-080 C-CAP,S 0.1-50 F C153 87-A11-595-080 C-CAP,S 0.056-50 K B

DESCRIPTIONREF. NO. KANRI

PART NO.

NO.

C154 87-A11-595-080 C-CAP,S 0.056-50 K B C155 87-010-190-080 S CHIP F 0.01 C156 87-010-190-080 S CHIP F 0.01 C157 87-010-190-080 S CHIP F 0.01 C160 87-010-186-080 CAP,CHIP 4700P

C161 87-010-186-080 CAP,CHIP 4700P C200 87-018-131-080 CAP,TC U 1000P-50 K B C201 87-010-178-080 CHIP CAP 1000P C202 87-010-258-080 CAP,E 22-35 SME C203 87-010-322-080 C-CAP,S 100P-50 J CH GRM

C204 87-010-258-080 CAP,E 22-35 SME C205 87-010-260-080 CAP, ELECT 47-25V C206 87-012-156-080 C-CAP,S 220P-50 CH C208 87-010-197-080 CAP, CHIP 0.01 DM C209 87-010-260-080 CAP,E 47-25 M 11L SME

C210 87-010-260-080 CAP,E 47-25 M 11L SME C251 87-012-368-080 C-CAP,S 0.1-50 F C252 87-A11-595-080 C-CAP,S 0.056-50 K B C253 87-A11-595-080 C-CAP,S 0.056-50 K B C258 87-010-178-080 C-CAP,S 1000P-50 K B

CN101 87-A61-109-010 CONN,7P V TID-A CN102 87-A60-135-010 CONN,10P V FE FC102 88-910-201-110 FF-CABLE 10P 1.25 J101 87-A61-159-010 JACK,PIN 4P R/W/B/0 KM L151 87-A50-610-010 COIL,1UH-K

L152 87-A50-610-010 COIL,1UH-K L251 87-A50-610-010 COIL,1UH-K R131 87-A00-258-080 RES,M/F 0.22-1W J R132 87-A00-258-080 RES,M/F 0.22-1W J R171 87-A00-258-080 RES,M/F 0.22-1W J

R172 87-A00-258-080 RES,M/F 0.22-1W J R218 87-A00-257-080 RES,M/F 0.15-1W J R278 87-A00-257-080 RES,M/F 0.15-1W J TH201 87-A91-042-080 C-THMS,100K 55001

KEY CD C.B

CN701 87-A60-156-010 CONN,8P H FE FC701 88-908-231-110 FF-CABLE,8P 1.25 LED771 87-A40-317-080 LED,SLR-342VCT31 RED LED772 87-A40-317-080 LED,SLR-342VCT31 RED LED773 87-A40-317-080 LED,SLR-342VCT31 RED

LED774 87-A40-317-080 LED,SLR-342VCT31 RED LED775 87-A40-317-080 LED,SLR-342VCT31 RED S751 87-A90-095-080 SW,TACT EVQ11G04M S752 87-A90-095-080 SW,TACT EVQ11G04M S753 87-A90-095-080 SW,TACT EVQ11G04M

S754 87-A90-095-080 SW,TACT EVQ11G04M S755 87-A90-095-080 SW,TACT EVQ11G04M S756 87-A90-095-080 SW,TACT EVQ11G04M S757 87-A90-095-080 SW,TACT EVQ11G04M

DK1 LED C.B

LED724 87-A40-619-040 LED,SLR-56PT-T31-W GRN LED725 87-A40-589-040 LED,SLR-56VCT31 RED LED726 87-A40-619-040 LED,SLR-56PT-T31-W GRN

DK2 LED C.B

CN721 87-A60-619-010 CONNECTOR 2P V 2MM CNA722 8A-MA3-653-010 CONN ASSY,2P V 100MM LED721 87-A40-619-040 LED,SLR-56PT-T31-W GRN LED722 87-A40-589-040 LED,SLR-56VCT31 RED LED723 87-A40-619-040 LED,SLR-56PT-T31-W GRN

MIC C.B

C601 87-010-196-080 CHIP CAPACITOR,0.1-25 CN601 87-A60-619-010 CONNECTOR 2P V 2MM FB603 83-XM1-617-080 C-COIL,BK 2125HM 601

– 10 –

Page 11

PART NO. DESCRIPTIONREF. NO. KANRI

DESCRIPTIONREF. NO. KANRI

NO.

J601 87-099-659-010 JACK,6.3 JY-6314-01130 J602 87-099-659-010 JACK,6.3 JY-6314-01130

VM C.B

PT C.B

C1 87-A11-148-080 CAP,TC U 0.1-50 Z F C2 87-A11-148-080 CAP,TC U 0.1-50 Z F C3 87-A11-148-080 CAP,TC U 0.1-50 Z F C4 87-A11-148-080 CAP,TC U 0.1-50 Z F C5 87-A11-148-080 CAP,TC U 0.1-50 Z F

C6 87-A11-148-080 CAP,TC U 0.1-50 Z F C7 87-A11-148-080 CAP,TC U 0.1-50 Z F C8 87-A11-148-080 CAP,TC U 0.1-50 Z F C101 87-010-387-080 CAP,E 470-25 SME C103 87-A11-148-080 CAP,TC U 0.1-50 Z F

C104 87-A11-148-080 CAP,TC U 0.1-50 Z F C105 87-A11-148-080 CAP,TC U 0.1-50 Z F C106 87-A11-148-080 CAP,TC U 0.1-50 Z F C107 87-A11-148-080 CAP,TC U 0.1-50 Z F C108 87-A11-148-080 CAP,TC U 0.1-50 Z F

C109 87-A11-148-080 CAP,TC U 0.1-50 Z F C110 87-A11-148-080 CAP,TC U 0.1-50 Z F C111 87-010-917-000 CAP,E 3300-50 M SMG C112 87-010-917-000 CAP,E 3300-50 M SMG C113 87-A10-231-090 CAP,E 3300-80

C114 87-A10-231-090 CAP,E 3300-80 C116 87-010-403-040 CAP,E 3.3-50 SME CN1 87-A61-110-010 CONN,9P V TID-A CN2 87-A61-108-010 CONN,5P V TID-A

F101 87-035-458-010 FUSE,4A 250V T 218

F102 87-035-458-010 FUSE,4A 250V T 218

FC101 87-033-213-080 CLAMP, FUSE FC102 87-033-213-080 CLAMP, FUSE

FC103 87-033-213-080 CLAMP, FUSE

FC104 87-033-213-080 CLAMP, FUSE

PR103 87-026-682-080 PROTECTOR,10A 491SERIES 60V

PR106 87-026-682-080 PROTECTOR,10A 491SERIES 60V

PT1 8A-MGP-664-010 PT,AMG-P HR1<770>

PT1 8A-MGP-665-010 PT,AMG-P HR2<970>

PT2 8A-NF8-673-010 PT,SUB ANF-8 (H)

RY101 87-A91-300-010 RELAY,AC 12V-ALA2PF12

S101 87-A90-165-010 SW,SL 1-2-3 SWS2301

T101 87-A60-317-010 TERMINAL, 1P MSC

T102 87-A60-317-010 TERMINAL, 1P MSC

PART NO.

NO.

DECK C.B

CON502 87-099-756-010 CONN,15P 9604S F SFR1 87-024-581-010 SFR,3.3K DIA 6H SOL1 82-ZM1-626-010 SOL ASSY,27K SOL2 82-ZM1-626-010 SOL ASSY,27K SW1 87-A90-248-010 SW,MICRO ESE11SH2CXQ

SW2 87-A90-248-010 SW,MICRO ESE11SH2CXQ SW3 87-A90-248-010 SW,MICRO ESE11SH2CXQ SW4 87-036-110-010 SW,MICRO SPPB62 SW5 87-036-110-010 SW,MICRO SPPB62 SW6 87-036-110-010 SW,MICRO SPPB62

SW8 87-A90-248-010 SW,MICRO ESE11SH2CXQ SW9 87-A90-248-010 SW,MICRO ESE11SH2CXQ W1 82-ZM3-601-010 RBN-CORD,4P-75

HEAD-1 C.B

85-ZM3-601-010 PWB,FLEX I CON301 8Z-NF3-643-010 CONN ASSY,3P-PB

HEAD-2 C.B

85-ZM3-601-010 PWB,FLEX I CON351 8Z-NF3-644-010 CONN ASSY,8P-RPB

KEY CON C.B

C551 87-A10-060-080 C-CAP,S 0.18-16 K B C552 87-A10-060-080 C-CAP,S 0.18-16 K B C553 87-012-154-080 C-CAP,S 150P-50 J CH GRM C554 87-012-154-080 C-CAP,S 150P-50 J CH GRM C555 87-012-145-080 C-CAP,S 270P-50 J CH GRM

C556 87-012-145-080 C-CAP,S 270P-50 J CH GRM C557 87-010-183-080 C-CAP,S 2700P-50 K B GRM C559 87-010-196-080 C-CAP,S 0.1-25 Z F C560 87-010-177-080 C-CAP,S 820P-50 J SL C2012 C561 87-010-177-080 C-CAP,S 820P-50 J SL C2012

C562 87-010-196-080 C-CAP,S 0.1-25 Z F C563 87-010-374-080 CAP,E 47-10 M 11L SME C564 87-010-196-080 C-CAP,S 0.1-25 Z F C565 87-010-263-080 CAP,E 100-10 M 11L SME C567 87-010-183-080 C-CAP,S 2700P-50 K B GRM

C571 87-016-460-080 C-CAP,S 0.22-16 K B C572 87-016-460-080 C-CAP,S 0.22-16 K B C573 87-016-460-080 C-CAP,S 0.22-16 K B C577 87-010-196-080 C-CAP,S 0.1-25 Z F CN551 87-A60-689-010 CONN,7P H GRY TUC-P07X-C1

CHIP RESISTOR PART CODE

Chip Resistor Part Coding

Resistor Code

Chip resistor

Wattage Type Tolerance 1/16W 1005 5% CJ

1/16W 1/10W

1/8W

1608 2125

3216

5% 5%

Symbol

CJ CJ

Figure

Value of resistor

Form

– 11 –

Dimensions (mm)

0.55

Resistor Code

108 118

128

LW t

1.0 0.5 0.35 104

1.6 0.8 0.45 2 1.25 0.45

3.2

1.6

: A : A

Page 12

TRANSISTOR ILLUSTRATION

KTA1266GR KTC3198GR CD1585BC CSA952K

E C B

DTC114ES KTC3199GR 2SA933SRS

E C B

CC5551 CSC4115BC

G D S

2SK3053

E C B

2SB1237Q

B C EE C B

2SB1370E 2SD1933 2SB1342 FN1016 FP1016 2SD2439 2SB1588

2SK2158

2SA1235F 2SC2714O 2SC3052F CMBT5551 CMBT5401 RT1P141C

KRA104S KRC102S-RTK KRA107S KRA102S 2SD1306E

– 12 –

Page 13

WIRING – 1 (MAIN / VM / KEY CON)

101112131415161718192021222324

1234567892526272829303132

– 13 –

Page 14

SCHEMATIC DIAGRAM - 1 (MAIN 1/4 : AMP / VM)

– 14 –

Page 15

SCHEMATIC DIAGRAM - 2 (MAIN 2/4 : DECK / HEAD-1 / HEAD-2 / KEY-CON)

AMP

– 15 –

Page 16

SCHEMATIC DIAGRAM - 3 (MAIN 3/4 : TUNER)

AMP

– 16 –

Page 17

SCHEMATIC DIAGRAM - 4 (MAIN 4/4 : PROLOGIC)

– 17 –

Page 18

WIRING – 2 (MICON)

101112131415161718192021222324

1234567892526272829303132

– 18 –

Page 19

SCHEMATIC DIAGRAM - 5 (MICON/DECK)

– 19 –

VRDM

Page 20

WIRING – 3 (CNTL)

101112131415161718192021222324

1234567892526272829303132

– 20 –

Page 21

SCHEMATIC DIAGRAM - 6 (CNTL/KEY CD/DK1 LED/KD2 LED/MIC)

– 21 –

Page 22

WIRING – 4 (KEY CD / DK1 LED / DK2 LED / MIC)

101112131415161718192021222324

1234567892526272829303132

– 22 –

Page 23

WIRING – 5 (AMP 1F)

101112131415161718192021222324

1234567892526272829303132

– 23 –

Page 24

SCHEMATIC DIAGRAM - 7 (AMP 1F)

– 24 –

Page 25

WIRING – 6 (AMP 2F)

101112131415161718192021222324

1234567892526272829303132

– 25 –

Page 26

SCHEMATIC DIAGRAM - 8 (AMP 2F)

– 26 –

Page 27

WIRING – 7 (PT)

123456789101112131415

– 27 –

Page 28

SCHEMATIC DIAGRAM - 9 (PT)

– 28 –

Page 29

WIRING – 8 (DECK / HEAD-1 / HEAD-2)

101112131415161718192021222324

1234567892526272829303132

– 29 –

Page 30

IC BLOCK DIAGRAM

– 30 –

Page 31

– 31 –

Page 32

– 32 –

Page 33

< TUNER SECTION >

1. Clock frequency Check Settings : • Test point : TP2 (CLK) Method : Set to AM 1602kHz and check that the test point is

2052kHz ± 45Hz.

2. AM VT Check Settings : • Test point : TP1 (VT) Method : Set to AM 1602kHz, 531kHz and check that the test

point is less than 8.0V (1602kHz) and more than

0.6V (531kHz).

3. FM VT Check Settings : • Test point : TP1 (VT) Method : Set to FM 87.5MHz, 108.0MHz and check

that the test point is more than 0.5V (87.5MHz) and less than 8.0V (108.0MHz).

< DECK SECTION >

8. Tape Speed Adjustment (DECK 2) Settings : • Test tape : TTA–100

• Test point : TP5(Lch), TP6(Rch)

• Adjustment location : SFR1

Method : Play back the test tape and adjust SFR1 so that the

frequency counter reads 3000Hz ± 5Hz and ± 45Hz (REV) with respect to forward speed.

9. Head Azimuth Adjustment (DECK 1, DECK 2) Settings : • Test tape : TTA–330

• Test point : TP5(Lch), TP6(Rch)

• Adjustment location : Head azimuth adjustment screw

Method : Play back (FWD) the 8kHz signal of the test tape and

adjust screw so that the output becomes maximum. Next, perform on REV PLAY mode.

4. AM Tracking Adjustment Settings : • Test point : TP5(Lch), TP6(Rch)

• Adjustment location :

L951(1/3) ........................................ 999kHz

Method : Set to AM 999kHz and adjust L951(1/3) to MAX.

5. FM Tracking Check Settings : • Test point : TP5(Lch), TP6(Rch) Method : Set to FM 98.0MHz and check that the test point is

less than 9dBµV.

6. AM IF Adjustment Settings : • Test point : TP5(Lch), TP6(Rch)

• Adjustment location :

L802 ................................................450kHz

7. DC Balance / Mono Distortion Adjustment Settings : • Test point : TP3, TP4 (DC balance)

• Test point : TP5(Lch), TP6(Rch)

• Adjustment location : L801

• Input level : 60dBµV

Method : Set to FM 98.0MHz and adjust L801 so that the

distortion is minimum. Then check the voltage between TP3 and TP4 is 0V ± 300mV.

10. PB Frequency Response Check (DECK 1, DECK 2) Settings : • Test tape : TTA–330

• Test point :TP5(Lch), TP6(Rch)

Method : Play back the 315Hz and 8kHz signals of the test tape

and check that the output ratio of the 8kHz signal with respect to that of the 315Hz signal is within 5dB.

11. PB Sensitivity Check (DECK 1, DECK 2) Settings : • Test tape : TTA–200

• Test point : TP5(Lch), TP6(Rch)

Method : Play back the test tape and check that the output level of

the test point is 230mV ± 3dB.

12. REC/PB Frequency Response Adjustment (DECK 2) Settings : • Test tape : TTA–602

• Test point : TP5(Lch), TP6(Rch)

• Input signal : 1kHz / 10kHz (LINE IN)

• Adjustment location : SFR351 (Lch) SFR352 (Rch)

Method : Apply a 1kHz signal and REC mode. Then adjust

OSC attenuator so that the output level at the TP5, TP6 becomes -20VU (16mV). Record and play back the 1kHz and 10kHz signals and adjust SFRs so that the output of the 10kHz signals becomes 0dB ± 0.5dB with respect to that of the 1kHz signal.

13. REC/PB Sensitivity Check (DECK 2) Settings : • Test tape : TTA–602

• Test point : TP5(Lch), TP6(Rch)

• Input signal : 1kHz (LINE IN)

Method : Apply a 1kHz signal and REC mode. Then adjust

OSC attenuator so that the output level at TP5, TP6 becomes 0VU (160mV). Record and play back the 1kHz signals and check that the output is 0dB ± 3.5dB.

– 33 –

< MICON SECTION >

14. µ-CON OSC Adjustment Settings : • Test point : TP7 (O-KSCAN)

• Adjustment location : L101

Method : Insert AC plug while pressing TUNER function key and

POWER on key. Adjust L101 so that the frequency at the test point is 208.80Hz ± 0.21Hz.

Page 34

IC DESCRIPTION

IC, LC876580W-5R55

Pin No. Pin Name I/O Description

1 M-CLK O Common serial clock.

2 M-DATA O Common serial data.

3 M-STB O Common serial strobe.

4 PLL-CE O Tuner PLL IC chip enable.

5 SR-LCK O Shift register IC LATCH clock.

6 RYM-CS O RHYTHM IC chip select.

7 POWER O Audio power ON/OFF.

8 MUTE O System MUTE ON/OFF.

9 C-SHIFT O CLOCK SHIFT output. "L" : SHIFT

10 HP-MUTE I Head phone jack detection. "L" : MUTE

11 RESET I System RESET input.

12 RTVR I Volume rotary encoder.

13 JOG I Dial JOG rotary encoder.

14 GND – Connected to GND.

15 CF1 I Oscillator circuit input.

16 CF2 O Oscillator circuit output.

17 VDD – Power supply.

18 HOLD I System HOLD input.

19 KEY1 I Tact key matrix 1 input.

20 KEY2 I Tact key matrix 2 input.

21 KEY3 I Tact key matrix 3 input.

22 CD-SW I CD MECHA SW matrix input.

23 DISH I CD turntable photo sensor.

24 SPEANA I Spectrum analyser level detection.

25 MIC I MIC input level detection.

26 RDS-SG I

27 TM-BASE I Time base clock input.

29 REM I Remote control signal input.

30 ~ 42 G13 ~ G1 O FL grid G13 ~ G1 output.

43 ~ 45 P38 ~ P36 O FL segment P38 ~ P36 output.

46 VDD – Power supply.

47 P35/SPEANA–A O FL segment P35 output / Spectrum analyser BPF switching control A output.

CD-WRQ/

RDS-CLK

RDS signal level input. (Not used)

I CD Read Write Request / Tuner RDS clock input (Not used).

48 P34/SPEANA–B O FL segment P34 output / Spectrum analyser BPF switching control B output.

49 P33/SPEANA–C O FL segment P33 output / Spectrum analyser BPF switching control C output.

50 P32/CSNDEMO O/I FL segment P32 output / Initial DEMO MODE detect. "H" : CASINO DEMO.

51 –VP – Power supply for FL.

52 P31/TU3 O/I FL segment P31 output / TUNER series, TU3 select (Not used).

53 P30/TU2 O/I FL segment P30 output / TUNER series, TU2 select.

54 P29/TU1 O/I FL segment P29 output / TUNER series, TU1 select.

– 34 –

Page 35

Pin No. Pin Name I/O Description

55 P28/DSP O/I FL segment P28 output / DSP function detection. "L" : ON (Not used).

56 P27/RHYTHM O/I FL segment P27 output / RHYTHM function detection. "H" : ON

57 P26/KEYCON O/I FL segment P26 output / KEYCON function detection. "H" : ON

58 P25/5MODE O/I FL segment P25 output / GEQ 5MODE select. "H" : 5 MODE (Not used)

59 P24/ECO O/I FL segment P24 output / ECO mode detection. "H" : ECO OFF

60 P23 O/I

61 P22 O/I FL segment P22 output.

62 P21/5.1+DLPRO O/I FL segment P21 output / 5.1CH+PROLOGIC detection. "H" : ON

63 P20/DLPRO O/I FL segment P20 output / DOLBY PROLOGIC detection. "H" : ON (Not used)

64 P19/CST2 O/I FL segment P19 output / Deck 2 cassette detection. "L" : ON

65 P18/REB O/I FL segment P18 output / Deck 2 side B recordable SW. "L" : REC

66 P17/CAM2 O/I FL segment P17 output / Deck 2 CAM SW input. "L" : ON

67 P16/AUTO1 O/I FL segment P16 output / Deck 1 auto stop input.

68 P15/AUTO2 O/I FL segment P15 output / Deck 2 auto stop input.

69 P14/CAM1 O/I FL segment P14 output / Deck 1 CAM SW input. "L" : ON

70 P13/CST1 O/I FL segment P13 output / Deck 1 cassette detection SW. "L" : ON

71 P12/REA O/I FL segment P12 output / Deck 2 side-A recordable SW. "L" : REC

72 VDD – Power supply.

73 ~ 83 P11 ~ P1 O FL segment P11 ~ P1 output.

84 P39 O FL segment P39 output.

85 KEYSCAN O KEYSCAN output. "L" : ON

86 MOTOR O DECK motor ON/OFF control. "L" : ON

87 SOL1 O DECK 1 solenoid control. "L" : ON

FL segment P23 output.

88 SOL2 O DECK 2 solenoid control. "L" : ON

89 GND – Connected to GND.

90 VDD – Power supply.

91 DISH-RVS O CD dish reverse output. "H" : REV

92 DISH-FWD O CD dish forward output. "H" : FWD

93 OPEN O CD tray OPEN output. "L" : OPEN

94 CLOSE O CD tray CLOSE output. "L" : CLOSE

96 CD-XLT O CD DSP serial LATCH output. (Chip enable)

97 CD-CLK O CD DSP serial CLOCK output.

98 CD-LED O CD flash window LED control.

100

CD-DATA/

RDS DATA RDS serial data input (Not used).

CD-SUBQ/IFC

DRF/STEREO

Serial data output to CD /

O/I

CD SUBQ (Sub code) serial data input / TUNER IF COUNT data input.

RF (radio frequency) detect / TUNER STEREO signal input.

– 35 –

Page 36

FL (BJ751GNK) GRID ASSIGNMENT AND ANODE CONNECTION

GRID ASSIGNMENT

– 36 –

Page 37

ANODE CONNECTION

– 37 –

Page 38

CD TEST MODE

1. Starting Up the CD Test Mode While pressing the “CD” button, connect the AC plug to the power outlet. When the CD test mode starts up, it displays “TEST” and all displays will turn on (Start Mode) in approximately 15 seconds.

2. How to Cancel the CD Test Mode To cancel the CD Test Mode, press the “POWER” button or disconnect the AC plug from the power outlet. *Press other function keys to cancel the test mode while playing.

3. Function Description and How to Use the CD Test Mode

No. Mode How to Control Display Operations Check List

1 Start Mode All lit * FL all lit * Check FL

* Check Micom

2 Search Mode STOP button CD * LD lights * Check APC circuit

* Continuous Focus Search *1 * Measure laser current * Continuous Spindle Motor kick * Check Focus Search Waveform

* Check Focus Error Waveform

(Ignore any DRF in Search Mode)

3 Play Mode PLAY button Normal * Normal Playback * Check Each Servo circuit

* If TOC reading is not possible, * Check DRF

Focus Search continues.

4 Traverse PAUSE button Normal * Tracking Servo OFF/ON * Check tracking balance

Mode Switch between OFF and ON

when PAUSE button is pressed.

5 Sled Mode FF button CD TEST * Shift PU to the outermost track.*2 * Check Sled circuit

Kick the lens to the * Check Tracking circuit outermost track simultaneously * Check Mechanism operation

* Check PU

RWD button CD TEST * Shift PU to the innermost track.*2

Kick the lens to the innermost track simultaneously.

* 1: If the focus search is continuously operated for more than 10 minutes, the driver IC will heat up high enough to trigger the protection circuit

to shut down the CD system. Turn off the main power and re-start it later.

* 2: When pressing FF or RWD buttons, take care to avoid damage to the gears. Because the sled motor is activated when the FF or RWD

buttons are pressed, even when the pick-up is at the outermost or innermost track.

– 38 –

Page 39

MECHANICAL EXPLODED VIEW 1 / 1

– 39 –

Page 40

MECHANICAL PARTS LIST 1 / 1

PART NO.

NO.

1 8A-MA3-094-010 RING,MAIN 2 8A-MA3-090-110 KNOB,RTRY MAIN 3 87-NF8-220-010 DMPR,150 4 82-NF5-219-010 SPR-T,EJECT 2 (SIN) 5 87-NF4-217-110 HLDR,LOCK 2

6 86-NF9-224-010 SPR-C,LOCK 7 82-NF5-229-010 PLATE,LOCK 8 86-NF6-061-010 REFLECTOR,CASS 9 8A-MA3-026-110 BOX,CASS R 10 8A-MA3-056-110 WINDOW,CASS R

11 8A-MA3-036-010 PANEL,CASS R 3 12 8A-MA3-025-110 BOX,CASS L 13 8A-MA3-055-110 WINDOW,CASS L 14 8A-MA3-035-010 PANEL,CASS L 3 15 8A-MA3-041-110 PANEL,FUN 5F

16 81-532-080-010 LABEL, CASS. COMPT 17 8A-MA3-102-010 REFLECTOR,FUN 5F 18 8A-MGP-051-010 WINDOW,DISP VCD P 770<770HR> 18 8A-MGP-050-010 WINDOW,DISP VCD P 970<970HR> 19 82-NF5-218-010 SPR-T,EJECT 1 (SIN)

20 8A-MA3-034-010 PANEL,CD LED 21 8A-MG3-037-010 PANEL ASSY,TRAY VCD 3 22 87-NF4-216-010 HLDR,LOCK 1 23 8A-MAP-110-010 PLATE,DPL 24 87-B00-002-010 BADGE,AIWA 30 ABS SIL

25 8A-MA3-093-010 KNOB ASSY,RTRY JOG 26 8A-MGP-030-010 PANEL,FR VCD P 27 8A-MA3-071-010 KEY,TIMER 28 8A-MA3-072-010 KEY,FREQ 29 8A-MA3-073-010 KEY,ENTER

30 8A-MA3-074-010 KEY,RHYTHM 31 8A-MGP-069-010 KEY,PBC P 32 8A-MA3-080-010 KEY ASSY,GEQ 4M PM 33 8A-MA3-210-110 GUIDE,LED OPE 34 8A-MG3-070-010 KEY,CONT 3

35 8A-MA3-084-010 KEY ASSY,FF 36 8A-MAP-066-010 KEY,FUN 5.1CH 5F 37 8A-MA3-083-010 KEY ASSY,DIR 38 8A-MA3-057-010 WINDOW,TOP 39 8A-MA3-020-110 CABI,TOP

40 8A-MA3-101-010 REFLECTOR,POWER 41 8A-MA3-075-010 KEY,POWER 42 88-MA1-205-010 GUIDE FL 43 8A-MA3-061-010 KEY,CD 44 8A-MA3-100-010 REFLECTOR,CD

DESCRIPTIONREF. NO. KANRI

PART NO.

45 8A-MAP-001-010 CABI,FR DPL 3 46 8A-MA3-062-110 KEY,MIC 47 8A-MA3-207-010 HLDR,PWB MAIN H 48 88-MA1-208-210 JOINT,CABI 49 8A-MA3-212-010 HLDR,PWB PT

50 8A-MA2-202-010 HLDR,FAN 51 8A-MA3-211-010 COVER, FAN 52 87-064-185-010 HLDR,WIRE 53 87-A91-711-010 FAN, 3110GL-B4W-B34-H02 -400MM 54 84-ZG1-245-210 CAP,OPTICAL

55 8A-MGP-011-010 CABI,REAR HR P 56 8A-MA3-214-010 W,3.5-6.5-1 W/ADH 57 82-NF7-599-010 W-F,3.2-8-1.0 58 8A-NF3-221-010 HLDR,IC-VM 59 8A-MA3-205-110 HLDR,HT-SINK L

60 8A-MA3-206-110 HLDR,HT-SINK R 61 87-A91-423-010 FAN,AD0612DS-D7OGL 62 8A-NF3-223-010 HLDR,FAN

63 87-A80-148-010 AC CORD ASSY,E BLK 64 87-085-185-010 BUSHING, AC CORD (E)

65 87-MA3-062-010 FOOT, H17 66 8A-MA3-045-010 PANEL,SIDE L 3 67 8A-MA3-046-010 PANEL,SIDE R 3 A 87-078-060-010 BVIT3PB+3-10 B 87-591-095-410 TAPPING SCREW, QIT+3-8 (GLD)

C 87-NF4-224-010 S-SCREW,IT3B+3-8 CU D 81-MK1-210-010 S-SCREW,VFT2+3-16 E 87-067-688-010 BVTT+3-6 F 87-067-975-010 S-SCREW,IT+4-8 G 87-067-703-010 TAPPING SCREW, BVT2+3-10

H 87-067-758-010 BVT2+3-12 W/O SLOT I 87-067-581-010 TAPPING SCREW, BVT2+3-15 J 87-067-579-010 TAPPING SCREW, BVT2+3-8 K 87-067-641-010 UTT2+3-8(W/O SLOT)BL L 87-067-822-010 BVT2+3-20 W/O SLOT

NO.

DESCRIPTIONREF. NO. KANRI

COLOR NAME TABLE

Basic color symbol Color Basic color symbol Color Basic color symbol Color

B Black C Cream D Orange

G Green H Gray L Blue

LT Transparent Blue N Gold P Pink

R Red S Silver ST Titan Silver T Brown V Violet W White

WT Transparent White Y Yellow YT Transparent Yellow

LM Metallic Blue LL Light Blue GT Transparent Green LD Dark Blue DT Transparent Orange GM Metallic Green

YM Metallic Yellow DM Metallic Orange PT Transparent Pink

– 40 –

Page 41

TAPE MECHANISM EXPLODED VIEW 1 / 1

(DECK 1)

DECK C.B

HLDR,IC

CUSH-G, DIA 3.7-8-3.25

2ZM3M(BOTOM) PR5N 12/3/24

CAPSTAN 2-41.5

CAPSTAN

2.2-41.7

SH, BELT D2

SH, 1.6-3.2-0.5 SLT

PLATE, SHLD M3

PH(DECK 1) RPH(DECK 2)

HEAD 1 C.B(DECK 1) HEAD 2 C.B(DECK 2)

(DECK 1)

(DECK 2)

2ZM3M(TOP SIDE) PR5N 12/3/24

– 41 –

Page 42

TAPE MECHANISM PARTS LIST 1 / 1

PART NO.

NO.

1 82-ZM3-301-610 CHAS ASSY,M2 2 82-ZM1-258-210 SPR-T,PINCH L 3 82-ZM1-341-210 LVR ASSY,PINCH L2 4 82-ZM1-333-210 PLATE,LINK2 5 82-ZM1-266-310 LVR,DIR

6 82-ZM1-214-010 SPR-T,DIR 7 82-ZM1-206-910 CHAS,HEAD 8 82-ZM3-335-310 PULLEY,COUPLER M3 9 82-ZM1-269-210 SPR-T,BRG 10 82-ZM1-219-110 SPR-T,LINK

11 82-ZM1-210-110 GEAR,H T 12 82-ZM1-213-010 SPR-T,HEAD 13 82-ZM1-207-910 GUIDE,TAPE 14 86-ZM4-206-010 S-SCREW,AZIMUTH L 15 82-ZM1-314-110 PLATE,HEAD

16 82-ZM1-208-310 HLDR,HEAD 17 82-ZM1-218-010 SPR-E,HB 18 86-ZM1-206-010 BELT,MAIN L 19 82-ZM1-222-210 LVR,PLAY 20 82-ZM1-217-410 REEL TABLE

21 82-ZM1-244-510 SPR-C,BT 22 82-ZM1-285-410 SPR-C,BT L 23 82-ZM1-257-010 SPR-T,CAS 24 82-ZM1-241-310 LVR,MC 25 82-ZM1-242-010 LVR,CAS

26 82-ZM1-243-010 LVR,STOP 27 82-ZM1-344-210 LVR ASSY,PINCH R2 28 82-ZM1-259-210 SPR-T,PINCH R 29 82-ZM1-240-110 LVR,REC(*) 30 82-ZM3-339-110 SHAFT,COUPLER N3

PART NO.DESCRIPTIONREF. NO. KANRI

NO.

31 82-ZM1-255-310 SPR-E,LVR DIR 32 82-ZM3-305-210 GEAR,CAM M2 33 82-ZM1-227-310 LVR,TRIG 34 82-ZM3-306-110 LVR,FR M2 35 82-ZM1-265-310 SPR-E,TRIG

36 82-ZM3-342-010 BELT,SBU MOT 3 37 80-ZM6-243-010 SH 1.75-3.6-0.5 SLT 38 82-ZM1-322-010 SPR-T,FR 60 39 82-ZM1-220-210 GEAR,IDLER 40 82-ZM3-616-010 RING MAGNET 4

41 82-ZM1-216-410 GEAR,REEL 42 87-A90-366-110 HEAD,PH YK50P-BF414 FPC 42 87-A90-367-110 HEAD,RPH YK56R-BF414 FPC 43 82-ZM1-225-210 GEAR,FR 44 82-ZM1-226-010 GEAR,REW

45 82-ZM3-333-310 SLIP DISK ASSY 2 46 82-ZM1-338-110 BELT,FR 4 47 82-ZM1-349-110 FLY-WHL,R W 47 82-ZM3-338-310 FLY-WHL,R3W 48 82-ZM1-348-110 FLY-WHL,L W

49 82-ZM3-329-410 BELT,SBU R2 50 82-ZM1-626-110 SOL ASSY,27K 51 87-045-347-010 MOT,SHU2L 70 52 82-ZM3-221-210 PULLEY,MOT 2M A 85-ZM3-202-010 S-SCREW,TG

B 80-ZM6-207-010 V+1.6-7 C 82-ZM3-318-110 S-SCREW W,MOTOR M2 D 87-B10-043-010 W-P,0.99-4-0.25 SLT E 82-ZM3-334-010 PW 2.16-6-0.4 F 82-ZM3-222-010 S-SCREW,SHILD PLATE

DESCRIPTIONREF. NO. KANRI

– 42 –

Page 43

SPEAKER DISASSEMBLY INSTRUCTIONS

Type.1

Insert a flat-bladed screwdriver into the position indicated by the arrows and remove the panel. Remove the screws of each speaker unit and then remove the speaker units.

Type.2

Remove the grill frame and four pieces of rubber caps by pulling out with a flat-bladed screwdriver. Remove the screws from hole where installed rubber caps. Insert a flat-bladed screwdriver into the position indicated by the arrows and remove the panel. Remove the screws of each speaker unit and then remove the speaker units.

Type.4

TOOLS

1 Plastic head hammer 2 (() flat head screwdriver 3 Cut chisel

12 3

How to Remove the PANEL, FR

1. Insert the (() flat head screwdriver tip into the gap

between the PANEL, FR and the PANEL, SPKR. Tap the head of the (() flat head screwdriver with the plastic hammer head, and create the clearance as shown in Fig-1.

2. Insert the cut chisel in the clearance, and tap the head of the cut chisel with plastic hammer as shown in Fig-2, to remove the PANEL, FR.

Type.3

Insert a flat-bladed screwdriver into the position indicated by the arrows and remove the panel. Turn the speaker unit to counterclockwise direction while inserting a flat-bladed screwdriver into one of the hollows around speaker unit, and then remove the speaker unit. After replacing the speaker unit, install it turning to clockwise direction until "click" sound comes out.

3. Place the speaker horizontally. Tap head of the cut chisel with plastic hammer as shown in Fig-3, and remove the PANEL, FR completely.

Fig-1 Fig-2

– 43 –

Fig-3

How to Attach the PANEL, FR

Attach the PANEL, FR to the PANEL, SPKR. Tap the four corners of the PANEL, FR with the plastic hammer to fit the PANEL, FR into the PANEL, SPKR completely.

Page 44

SPEAKER PARTS LIST (SX-ZHT730 <YSL> / SX-ZHT930 <YJSL, YJ7STL>)

PART NO.

NO.

1 8A-MSF-001-010 PANEL,FR 2 8A-MSF-002-010 RING,W 3 8A-MSF-003-010 PLATE,NAME 4 8A-MSF-004-010 PROTECTOR,TW 5 8A-MSF-005-010 GRILLE,FRAME ASSY

6 8A-NSJ-006-010 BADGE,AIWA S35 7 8A-MSD-601-010 SPKR,W 200 8 8A-MS2-605-110 SPKR,TW 60 9 88-NSK-610-010 SPKR,CERAMIC ASSY 10 87-NS7-611-010 CORD,SPKR

DESCRIPTIONREF. NO. KANRI

SPEAKER PARTS LIST (SX-CR677 <YJSTC, YJ7STL>)

NOTE: This SX-CR677 speaker contains SX-C607 (center speaker) and SX-R277 (surround speaker).

PART NO.

NO.

1 8Z-YS1-002-010 GRILLE,FRAME ASSY 2 81-VSA-009-010 CORD BUSH 3 8Z-YS1-601-010 SPKR, 100<YJSTC> 3 8Z-YS1-601-110 SPKR, 100<YJ7STL> 4 87-YS6-002-010 SPKR, CORD Y

5 87-YS7-012-010 PANEL,FR S 6 87-010-384-010 CAP,E 100-25 SME 7 87-YS3-003-010 GRILL FRAME ASSY 8 81-VSA-009-010 CORD BUSH 9 87-YS7-602-010 SPKR, 100<YJSTC>

9 87-YS7-604-010 SPKR, 100<YJ7STL> 10 83-NSM-010-010 SPEAKER CORD

DESCRIPTIONREF. NO. KANRI

ACCESSORIES / PACKAGE LIST

PART NO.

1 8A-MGP-901-010 IB,HR (ECA) M 2 87-A90-119-010 ANT,WIRE SW(5M) 3 87-006-226-010 ANT,LOOP AM 4 8Z-NHT-702-010 RC UNIT,RC-ZAS08 5 87-043-115-010 FEEDER-ANT,FM

6 87-050-103-010 CORD,PIN 1PY1.5M 7 87-099-789-010 PLUG,CONVERSION IR44

NO.

DESCRIPTIONREF. NO. KANRI

– 44 –

Page 45

2–11, IKENOHATA 1–CHOME, TAITO-KU, TOKYO 110, JAPAN TEL:03 (3827) 3111

Printed in Singapore9301978 9630472 0251431