Aiwa XS-G7, XS-G9 Service Manual

XS-G7

EZ

XS-G9

EZ

SERVICE MANUAL

COMPACT DISC

STEREO SYSTEM

CD STEREO

RECEIVER

XS-G7

XS-G9

• This Service Manual is the “Revision Publishing” and replaces
“Simple Manual” of XS-G7 / G9 <EZ>, (S/M Code No. 09-015-446-2T1).

• If requiring information about the CD mechanism, see Service Manual of

BZG-5, (S/M Code No. 09-00C-353-3N4).

CX-G7

CX-G9

BASIC CD MECHANISM : BZG-5 ZD3GNDM

SPEAKERSYSTEM

SX-G7

SX-G9

REMOTE

CONTROLLER

RC-BAS15

S/M Code No. 09-017-446-2R1

REVISION

DATA

SPECIFICATIONS

MAIN UNIT CX-G7 / CX-G9

TUNER
FM tuning range 87.5 MHz to 108 MHz
FM usable sensitivity (IHF) 16.8 dBf
FM antenna terminal 75 ohms (unbalanced)
MW tuning range 531 kHz to 1602 kHz (9 kHz step)

530 kHz to 1710 kHz (10 kHz step)

MW usable sensitivity 350 µV/m
LW tuning range 144 kHz to 290 kHz
LW usable sensitivity 1400 µV/m
MW/LW antenna Loop antenna

AMPLIFIER
Power output Rated: 56 W + 56 W

(6 ohms, THD 1 %, 1 kHz/DIN 45500)
Reference: 70 W + 70 W
(6 ohms, THD 10 %, 1 kHz/DIN 45324)
DIN MUSIC POWER: 190 W + 190 W

Total harmonic distortion 0.08 % (25 W, 1 kHz, 6 ohms,

DIN AUDIO)

Inputs VIDEO/AUX: 500 mV

MD: 500 mV
MIC: 1.0 mV (10 kohms)

Outputs FRONT SPEAKERS: 6 ohms or more

SURROUND SPEAKERS: 8 ohms to
16 ohms
SUB WOOFER: 1.8 V
LINE OUT: 80 mV
CD DIGITAL OUT (OPTICAL)
PHONES: 32 ohms or more
AC OUTLET: Switched

CD PLAYER
Laser Semiconductor laser (λ = 780 nm)
D/A converter 1 bit dual
Signal-to-noise ratio 85 dB (1 kHz, 0 dB)
Harmonic distortion 0.05 % (1 kHz, 0 dB)

GENERAL
Power requirements 230 V AC, 50 Hz
Power consumption 130 W
Standby power consumption ECO ON: 0.6 W

ECO OFF: 20 W

Dimensions (W x H x D) 260 x 266 x 350 mm
Weight 8.3 kg

FRONT SPEAKERS SX-G7 (for XS-G7)

Speaker system 2 way, bass reflex (magnetic shielded)
Speaker units Woofer: 140 mm cone

Tweeter: 25 mm dome

Impedance 6 ohms
Dimensions (W x H x D) 182 x 328 x 269 mm
Weight 3.8 kg

FRONT SPEAKERS SX-G9 (for XS-G9)

Speaker system 2 way, bass reflex (magnetic shielded)
Speaker units Woofer: 140 mm cone

Tweeter: 25 mm dome

Impedance 6 ohms
Dimensions (W x H x D) 182 x 328 x 250 mm
Weight 4.0 kg

• Design and specifications are subject to change without notice.

• The word "BBE"and the "BBE symbol" are trademarks of BBE

Sound, Inc.

Under license from BBE Sound,Inc.

– 2 –

PROTECTION OF EYES FROM LASER BEAM DURING SERVICING

This set employs laser. Therefore, be sure to follow carefully the

instructions below when servicing.

WARNING!!

WHEN SERVICING, DO NOT APPROACH THE LASER
EXIT WITH THE EYE TOO CLOSELY. IN CASE IT IS
NECESSARY TO CONFIRM LASER BEAM EMISSION.
BE SURE TO OBSERVE FROM A DISTANCE OF MORE
THAN 30cm FROM THE SURFACE OF THE OBJECTIVE
LENS ON THE OPTICAL PICK-UP BLOCK.

Caution: Invisible laser radiation when
open and interlocks defeated avoid
exposure to beam.
Advarsel: Usynlig laserståling ved åbning,
når sikkerhedsafbrydere er ude af funktion.
Undgå udsættelse for stråling.

VAROITUS!

Laiteen Käyttäminen muulla kuin tässä käyttöohjeessa
mainitulla tavalla saataa altistaa käyt-täjän
turvallisuusluokan 1 ylittävälle näkymättömälle
lasersäteilylle.

VARNING!

Om apparaten används på annat sätt än vad som
specificeras i denna bruksanvising, kan användaren
utsättas för osynling laserstrålning, som överskrider
gränsen för laserklass 1.

CAUTION

Use of controls or adjustments or performance of proce­dures other than those specified herin may result in
hazardous radiation exposure.

ATTENTION

Lutillisation de commandes, réglages ou procédures
autres que ceux spécifiés peut entraîner une dangereuse
exposition aux radiations.

ADVARSEL

Usynlig laserståling ved åbning, når sikkerhedsafbrydereer
ude af funktion. Undgå udsættelse for stråling.

This Compact Disc player is classified as a CLASS 1
LASER product.
The CLASS 1 LASER PRODUCT label is located on the
rear exterior.

CLASS 1 LASER PRODUCT
KLASSE 1 LASER PRODUKT
LUOKAN 1 LASER LAITE
KLASS 1 LASER APPARAT

Precaution to replace Optical block

(KSS-213F)

Body or clothes electrostatic potential could

ruin laser diode in the optical block. Be sure

ground body and workbench, and use care the

clothes do not touch the diode.

1) After the connection, remove solder shown in
right figure.

CD PICK-UP Assy PWB

Solder

 3 

NOTE ON BEFORE STARTING REPAIR

1. Forced discharge of electrolytic capacitor of power supply block

When repair is going to be attempted in the set that uses relay circuit in the power supply block, electric potential is kept charged across
the electrolytic capacitors (C101, 102) even though AC power cord is removed. If repair is attempted in this condition, secondary defect
can occur.
In order to prevent the secondary trouble, perform the following measures before starting repair work.

Discharge procedure

11

1 Remove the AC power cord.

11
22

2 Connect a discharging resistor at an end of lead wire that

22

has clips at both ends. Connect the other end of the lead
wire to metal chassis.

33

3 Contact the other end of the discharging resistor to the

33

positive (+) side (+VH) of C101. (For two seconds)

44

4 Contact the same end of the discharging resistor as step

44

33

3 to the negative (-) side (-VH) of C102 in the same way.

33

(For two seconds)

55

5 Check that voltage across C101 and C102 has decreased

55

to 1 V or less using a multimeter or an oscilloscope.

Select a discharging resistor referring to the following table.

Charging voltage (V) Discharging

(C101, 102) resistor (Ω)

25-48 100 3 87-A00-247-090

49-140 220 5 87-A00-232-090

Note: The reference numbers (C101, C102) of the electrolytic capacitors can change depending on the models. Be sure to check the

reference numbers of the charging capacitors on schematic diagram before starting the discharging work.

Rated power (W) Parts number

MAIN C.B

D101

3

C101 C102

22

Fig-1

4

2. Check items before exchanging the MICROCOMPUTER

Be sure to check the following items before exchanging the MICROCOMPUTER. Exchange the MICROCOMPUTER after confirming
that the MICROCOMPUTER is surely defective.

2-1. Regarding the HOLD terminal of the MICROCOMPUTER

When the HOLD terminal (INPUT) of the MICROCOMPUTER is “H”, the MICROCOMPUTER is judged to be operating correctly.
When this terminal is “L”, the main power cannot be turned on. Therefore, be sure to check the terminal voltage of the HOLD
terminal before exchange.
When the MICROCOMPUTER is not defective, the HOLD terminal can also go “L” when the POWER AMPLIFIER has any
abnormalities that triggers the abnormality detection circuit on the MAIN C. B. that sets the HOLD terminal to “L”.

• Good or no good judgement of the MICROCOMPUTER

11

1 Turn on the AC main power.

11
22

2 Confirm that the main power is turned on and the HOLD terminal of the MICROCOMPUTER keeps the “H” level or not.

22
33

3 When the HOLD terminal is “L” level, the abnormality detection circuit is judged to be working correctly and the

33

MICROCOMPUTER is judged to be good.

– 4 –

In such a case, check also if the POWER AMPLIFIER circuit or power supply circuit has any abnormalities or not.

2-2. Regarding reset

There are cases that the machine does not work correctly because the MICROCOMPUTER is not reset even though the AC power
cord is re-inserted, or the software reset (pressing the STOP key + POWER key) is performed.
When the above described phenomenon occurs, it can lead to wrong judgement as if the MICROCOMPUTER is defective and to
exchange the MICROCOMPUTER. In such a case, perform the forced-reset by the following procedure and check good or no
good of the MICROCOMPUTER.

11

1 Remove the AC power cord.

11

FRONT C.B

18

MICROCOMPUTER

FRONT C.B

22

2 Short both ends of the electrolytic capacitor C113 that is connected to VDD of the MICROCOMPUTER with tweezers.

22
33

3 Connect the AC power cord again. If the MICROCOMPUTER returns to the normal operation, the MICROCOMPUTER is

33

good.

Note: The reference number or MICROCOMPUTER pin number of transistor (Q110) and electrolytic capacitor (C113) can change depending

on the models. Be sure to check the reference numbers on schematic diagram before starting the discharging work.

15

C113

Short with tweezers.

Fig-2-2

C113

%

*

VSS

VDD

MICRO­COMPUTER

2-3. Confirmation of soldering state of MICROCOMPUTER

Check the soldering state of the MICROCOMPUTER in addition to the above described procedures. Be sure to exchange the
MICROCOMPUTER after surely confirming that the trouble is not caused by poor soldering but the MICROCOMPUTER itself.

– 5 –

PHASE ALIGNMENT

How to install HLDR MECHA ASSY

1. Align the PLATE MAIN CAM of the HLDR MECHA ASSY to the position as shown in the diagram below.

HLDR MECHA ASSY

SECOND TEETH PLATE

PLATE CAM

2. Install the HLDR MECHA ASSY with the display part of the main unit in a lowered position.

DISPLAY

FRONT

* When assembling HLDR MECHA ASSY, particular phase alignment is not required.

– 6 –

ELECTRICAL MAIN PARTS LIST

PART NO. DESCRIPTIONREF. NO. KANRI

NO.

IC

8B-NFW-601-030 C-IC,LC877264V-5W17
87-A21-831-010 IC,SPS-422-1-F1
87-A21-401-040 C-IC,M61503FP
87-A21-021-040 C-IC,BU2099FV
87-A21-023-040 C-IC,BA3835F

87-A21-695-010 IC,LA1845L
87-A20-440-040 C-IC,BU1920FS
87-070-127-110 IC,LC72131D-N

TRANSISTOR

87-A30-559-010 TR,CSB1370EF
87-026-610-080 TR,KTC3198GR
87-A30-076-080 C-TR,2SC3052F
87-A30-075-080 C-TR,2SA1235F
87-A30-494-080 TR,2SA1980G

87-A30-635-040 C-TR,SBT5401F
87-A30-484-080 C-TR,KRA102S
87-A30-190-080 TR,CC5551
87-A30-636-040 C-TR,SBT5551F
87-A30-528-010 TR,2SB1686

87-A30-529-010 TR,2SD2642
87-A30-087-080 C-FET,2SK2158
87-A30-490-080 C-TR,KRC107S
87-A30-047-080 TR,CSD655E
87-A30-074-080 C-TR,RT1P141C

87-A30-071-080 C-TR,RT1N144C
87-A30-162-010 FET,2SK2937
87-A30-520-080 TR,2SC5342Y
87-A30-515-080 TR,2SA1979O/Y
87-A30-090-080 FET,2SK2541

87-A30-435-040 C-TR,DTC144EKA
89-327-143-080 C-TR,2SC2714O
87-A30-489-080 C-TR,KRA107S
87-A30-086-040 C-TR,CSD1306E
89-503-602-080 C-FET,2SK360E

87-A30-234-080 TR,CSC4115BC

DIODE

87-A40-291-080 DIODE,1N4148M (CPT)
87-A40-839-090 DIODE,G5SBA60L-6088
87-A40-455-090 DIODE,RL203 GW
87-A40-764-080 ZENER,UZ10BSC
87-A40-553-080 DIODE,1N4003 LES

87-A40-270-080 C-DIODE,MC2838
87-A40-269-080 C-DIODE,MC2836
87-A40-748-080 ZENER,UZ5.6BSA
87-020-465-080 DIODE,1SS133
87-A40-393-090 DIODE,1N5402GW(F20)

87-A40-747-080 ZENER,UZ5.1BSB
87-A40-749-080 ZENER,UZ5.6BSB
87-A40-739-080 ZENER,UZ2.7BSA
87-017-149-080 ZENER,HZS6A2L

MAIN C.B

C3 87-012-368-080 C-CAP,S 0.1-50 F
C4 87-012-368-080 C-CAP,S 0.1-50 F
C5 87-012-368-080 C-CAP,S 0.1-50 F
C6 87-012-368-080 C-CAP,S 0.1-50 F
C9 87-010-759-080 C-CAP,U, 0.1-25F

C10 87-010-759-080 C-CAP,U, 0.1-25F
C11 87-010-759-080 C-CAP,U, 0.1-25F
C12 87-010-759-080 C-CAP,U, 0.1-25F
C19 87-A12-036-000 CAP,E 2200-63 SMG
C20 87-A12-036-000 CAP,E 2200-63 SMG

C21 87-A10-520-000 CAP,E 3300-35 M SMG

DESCRIPTIONREF. NO. KANRI

PART NO.

NO.

C22 87-A10-520-000 CAP,E 3300-35 M SMG
C32 87-012-286-080 CAP, U 0.01-25
C34 87-A12-072-080 CAP,E 100-25 SMG
C35 87-A12-090-080 CAP,E 4.7-50 SMG
C36 87-A12-066-080 CAP,E 47-16 SMG

C38 87-012-286-080 CAP, U 0.01-25
C60 87-A12-089-080 CAP,E 3.3-50 SMG
C61 87-A12-071-080 CAP,E 47-25 SMG
C83 87-A12-068-080 CAP,E 470-16 SMG
C97 87-010-831-080 C-CAP,U,0.1-16F

C101 87-012-279-080 C-CAP,U 2700P-50 B
C102 87-012-279-080 C-CAP,U 2700P-50 B
C103 87-A12-084-080 CAP,E 0.22-50 SMG
C104 87-A12-084-080 CAP,E 0.22-50 SMG
C107 87-A12-089-080 CAP,E 3.3-50 SMG

C108 87-A12-089-080 CAP,E 3.3-50 SMG
C109 87-012-195-080 C-CAP,U 100P-50CH
C110 87-012-195-080 C-CAP,U 100P-50CH
C111 87-A12-077-080 CAP,E 33-35 SMG
C112 87-A12-077-080 CAP,E 33-35 SMG

C113 87-A10-596-080 C-CAP,S 100P-100 J CH
C114 87-A10-596-080 C-CAP,S 100P-100 J CH
C117 87-012-368-080 C-CAP,S 0.1-50 F
C118 87-012-368-080 C-CAP,S 0.1-50 F
C119 87-012-286-080 CAP, U 0.01-25

C120 87-012-286-080 CAP, U 0.01-25
C123 87-010-177-080 C-CAP,S 820P-50 SL
C124 87-010-177-080 C-CAP,S 820P-50 SL
C133 87-012-282-080 CAP, U 4700P-50
C140 87-012-278-080 C-CAP,U 2200P-50 B

C186 87-010-759-080 C-CAP,U, 0.1-25F
C187 87-010-866-080 CAP, ELECT 10-63
C188 87-010-866-080 CAP, ELECT 10-63
C225 87-012-368-080 C-CAP,S 0.1-50 F
C226 87-012-368-080 C-CAP,S 0.1-50 F

C227 87-012-368-080 C-CAP,S 0.1-50 F
C228 87-012-368-080 C-CAP,S 0.1-50 F
C229 87-010-191-080 C-CAP,S 0.015-50 F
C230 87-010-191-080 C-CAP,S 0.015-50 F
C231 87-012-286-080 CAP, U 0.01-25

C232 87-012-286-080 CAP, U 0.01-25
C235 87-A12-094-080 CAP,E 47-50 SMG
C236 87-A12-094-080 CAP,E 47-50 SMG
C241 87-010-831-080 C-CAP,U,0.1-16F
C609 87-010-785-080 C-CAP,U0.015-25BK

C610 87-010-785-080 C-CAP,U0.015-25BK
C611 87-A12-084-080 CAP,E 0.22-50 SMG
C612 87-A12-084-080 CAP,E 0.22-50 SMG
C613 87-A12-084-080 CAP,E 0.22-50 SMG
C614 87-A12-084-080 CAP,E 0.22-50 SMG

C615 87-012-172-080 CAPACITOR CHIP U 10P CH
C616 87-016-045-080 CAP,E 1000-6.3 M SMG
C617 87-016-459-080 CAP,E 470-10 M SMG
C618 87-A12-091-080 CAP,E 10-50 SMG
C620 87-A12-062-080 CAP,E 100-10 SMG

C623 87-A12-084-080 CAP,E 0.22-50 SMG
C624 87-A12-084-080 CAP,E 0.22-50 SMG
C630 87-A10-260-080 C-CAP,U 0.1-16 K B
C631 87-012-281-080 C-CAP,U 3900P-50 B
C632 87-012-281-080 C-CAP,U 3900P-50 B

C633 87-A11-070-080 C-CAP,U 0.033-16 K B
C634 87-A11-070-080 C-CAP,U 0.033-16 K B
C669 87-012-273-080 C-CAP,U 820P-50 B
C670 87-012-273-080 C-CAP,U 820P-50 B
C671 87-010-759-080 C-CAP,U, 0.1-25F

C672 87-010-759-080 C-CAP,U, 0.1-25F
C673 87-012-278-080 C-CAP,U 2200P-50 K B
C674 87-010-133-080 CAP, ELECT 2.2-50V
C675 87-010-133-080 CAP, ELECT 2.2-50V
C677 87-012-286-080 CAP, U 0.01-25

– 7 –

PART NO. DESCRIPTIONREF. NO. KANRI

NO.

C681 87-012-274-080 CHIP CAP,U 1000P-50B
C682 87-012-274-080 CHIP CAP,U 1000P-50B
C683 87-012-336-080 C-CAP,U 330P-50 J SL
C684 87-012-336-080 C-CAP,U 330P-50 J SL
C691 87-012-274-080 CHIP CAP,U 1000P-50B

C692 87-012-274-080 CHIP CAP,U 1000P-50B
C693 87-012-336-080 C-CAP,U 330P-50 J SL
C694 87-012-336-080 C-CAP,U 330P-50 J SL
C771 87-A12-062-080 CAP,E 100-10 SMG
C772 87-012-286-080 CAP, U 0.01-25

C779 87-010-949-080 CHIP CAPACITOR,S 0.01-50 BJ
C780 87-010-949-080 CHIP CAPACITOR,S 0.01-50 BJ
C782 87-012-286-080 CAP, U 0.01-25
C783 87-012-286-080 CAP, U 0.01-25
C784 87-012-286-080 CAP, U 0.01-25

C785 87-012-286-080 CAP, U 0.01-25
C786 87-012-286-080 CAP, U 0.01-25
C788 87-012-167-080 C-CAP,U 5P-50 CH
C789 87-016-118-080 C-CAP,U0.022-25BJ
C790 87-016-118-080 C-CAP,U0.022-25BJ

C791 87-010-831-080 C-CAP,U,0.1-16F
C792 87-012-286-080 CAP, U 0.01-25
C793 87-A12-090-080 CAP,E 4.7-50 SMG
C795 87-012-286-080 CAP, U 0.01-25
C796 87-012-286-080 CAP, U 0.01-25

C797 87-A12-091-080 CAP,E 10-50 SMG
C798 87-012-286-080 CAP, U 0.01-25
C799 87-010-407-080 CAP, ELECT 33-50V
C800 87-010-829-080 CAP, U 0.047-16
C801 87-A12-089-080 CAP,E 3.3-50 SMG

C802 87-010-829-080 CAP, U 0.047-16
C803 87-010-787-080 CAP, U 0.022-25
C804 87-A12-062-080 CAP,E 100-10 SMG
C807 87-A12-086-080 CAP,E 0.47-50 SMG
C808 87-A12-087-080 CAP,E 1-50 SMG

C809 87-A12-087-080 CAP,E 1-50 SMG
C810 87-010-831-080 C-CAP,U,0.1-16F
C814 87-012-286-080 CAP, U 0.01-25
C815 87-A12-086-080 CAP,E 0.47-50 SMG
C816 87-A12-086-080 CAP,E 0.47-50 SMG

C818 87-012-276-080 CAP, CHIP SS 1500 PBK
C821 87-A12-091-080 CAP,E 10-50 SMG
C823 87-A10-915-080 C-CAP,U 1000P-25 J CH
C824 87-A12-090-080 CAP,E 4.7-50 SMG
C825 87-010-596-080 CAP, S 0.047-16

C831 87-A12-092-080 CAP,E 22-50 SMG
C842 87-012-286-080 CAP, U 0.01-25
C843 87-010-197-080 CAP, CHIP 0.01 DM
C844 87-012-286-080 CAP, U 0.01-25
C845 87-010-197-080 CAP, CHIP 0.01 DM

C846 87-010-197-080 CAP, CHIP 0.01 DM
C847 87-010-197-080 CAP, CHIP 0.01 DM
C848 87-010-197-080 CAP, CHIP 0.01 DM
C849 87-010-197-080 CAP, CHIP 0.01 DM
C850 87-A12-071-080 CAP,E 47-25 SMG

C851 87-012-286-080 CAP, U 0.01-25
C852 87-012-286-080 CAP, U 0.01-25
C853 87-012-286-080 CAP, U 0.01-25
C858 87-010-831-080 C-CAP,U,0.1-16F
C859 87-010-831-080 C-CAP,U,0.1-16F

C860 87-012-286-080 CAP, U 0.01-25
C869 87-012-286-080 CAP, U 0.01-25
C870 87-012-274-080 CHIP CAP,U 1000P-50B
C871 87-012-199-080 CAP 220P
C872 87-012-199-080 CAP 220P

C873 87-A10-039-080 C-CAP,U 470P-50 J CH
C874 87-A12-091-080 CAP,E 10-50 SMG
C875 87-010-759-080 C-CAP,U, 0.1-25F
C876 87-A12-091-080 CAP,E 10-50 SMG
C877 87-012-286-080 CAP, U 0.01-25

DESCRIPTIONREF. NO. KANRI

PART NO.

NO.

C878 87-012-184-080 C-CAP,U 33P-50 CH
C879 87-012-180-080 C-CAP,U 22P-50 CH
C940 87-012-286-080 CAP, U 0.01-25
C942 87-012-165-080 CAP 3P
C947 87-012-286-080 CAP, U 0.01-25

C948 87-A10-039-080 C-CAP,U 470P-50 J CH
C952 87-012-286-080 CAP, U 0.01-25
C957 87-012-174-080 CAP CHIP CERA SS 12P CHJ
C958 87-012-286-080 CAP, U 0.01-25
C959 87-010-831-080 C-CAP,U,0.1-16F

C960 87-010-831-080 C-CAP,U,0.1-16F
C962 87-A12-087-080 CAP,E 1-50 SMG
C963 87-015-785-080 CHIP CAPACITOR, 0.1FZ-25Z
C971 87-A12-067-080 CAP,E 330-16 SMG
C972 87-A12-090-080 CAP,E 4.7-50 SMG

C973 87-012-286-080 CAP, U 0.01-25
C974 87-012-286-080 CAP, U 0.01-25
C979 87-012-195-080 C-CAP,U 100P-50CH
C981 87-A12-071-080 CAP,E 47-25 SMG
C982 87-010-831-080 C-CAP,U,0.1-16F

C983 87-012-286-080 CAP, U 0.01-25
C984 87-012-286-080 CAP, U 0.01-25
C985 87-012-195-080 C-CAP,U 100P-50CH
C987 87-012-286-080 CAP, U 0.01-25
C989 87-012-286-080 CAP, U 0.01-25

C991 87-012-176-080 CAP 15P
C992 87-012-176-080 CAP 15P
C993 87-012-274-080 CHIP CAP,U 1000P-50B
C995 87-012-274-080 CHIP CAP,U 1000P-50B
C997 87-010-831-080 C-CAP,U,0.1-16F

C998 87-A12-071-080 CAP,E 47-25 SMG
C999 87-A11-155-080 CAP,TC U 0.01-16 Z F
CF831 87-008-423-010 FLTR, CF SFE10.7MS3G-A
CF832 82-785-747-010 CF MS2 GHY R
CN501 87-099-564-010 CONN,4P V TUC-P4P-131

CN601 87-099-719-010 CONN,30P TYK-B(X)
CN602 87-099-194-010 CONN,6P V BLK 6216
CN605 87-A61-108-010 CONN,5P V TID-A
CNA1 8A-NF6-646-010 CONN ASSY,9P TID-A(460)
FFC602 88-906-401-110 FF-CABLE,6P 1.25

FFE831 A8-6ZA-19H-030 6ZA-1 FEMENM
J203 87-A60-238-010 TERMINAL,SP 4P (MSC)
J204 87-A60-244-010 JACK,PIN 1P BLK W/O SW
J205 87-A60-881-010 JACK,PIN 2P MSP 242V05 PBSN
J602 87-A60-885-010 JACK,PIN 6P R/W MSC

J832 87-A60-403-010 TERMINAL,ANT PAL 2P HSP-312V05
JR123 87-A10-596-080 C-CAP,S 100P-100 J CH
JR124 87-A10-596-080 C-CAP,S 100P-100 J CH
L201 87-A50-610-010 COIL,1UH K(MDEC)
L202 87-A50-610-010 COIL,1UH K(MDEC)

L801 87-A50-608-010 COIL,FM DET-N(TOK)
L802 87-A91-551-010 FLTR,PCFJZH-450 L(TOK)
L811 87-005-847-080 COIL,2.2UH K CECS
L832 87-005-847-080 COIL,2.2UH(CECS)
L861 87-005-847-080 COIL,2.2UH K CECS

L941 87-A50-020-010 COIL,ANT LW(COI) 252KHZ
L942 87-A50-019-010 COIL,OSC LW(COI) 856KHZ
L951 8A-NF8-668-010 COIL,AM PACK 2(TOK)
R129 87-A00-262-080 RES,M/F 0.15-2W J
R130 87-A00-262-080 RES,M/F 0.15-2W J

R131 87-A00-262-080 RES,M/F 0.15-2W J
R132 87-A00-262-080 RES,M/F 0.15-2W J
R790 87-012-286-080 CAP, U 0.01-25
R991 87-012-195-080 C-CAP,U 100P-50CH
R993 87-012-195-080 C-CAP,U 100P-50CH

R995 87-012-195-080 C-CAP,U 100P-50CH
TC942 87-A91-774-080 TRIMMER,PLY 30P 6.8X5.4 CDYL
TH101 87-A91-042-080 C-THMS,100K 55001
TH102 87-A91-042-080 C-THMS,100K 55001
WH1 87-A90-510-010 HLDR,WIRE 2.5-9P

– 8 –

PART NO. DESCRIPTIONREF. NO. KANRI

DESCRIPTIONREF. NO. KANRI

NO.

X862 87-A70-307-010 VIB,XTAL 4.332MHZ CSA-309ST
X992 87-A70-306-010 VIB,XTAL 4.500MHZ CSA-309ST

FRONT C.B

C141 87-012-278-080 C-CAP,U 2200P-50 B
C190 87-012-271-080 CAP, U 560P-50
C191 87-012-195-080 C-CAP,U 100P-50CH
C193 87-012-271-080 CAP, U 560P-50
C194 87-012-195-080 C-CAP,U 100P-50CH

C315 87-010-759-080 C-CAP,U, 0.1-25F
C441 87-010-412-040 CAP,E 10-25 5L
C503 87-010-112-040 CAP,E 100-16 M 11L SME
C504 87-016-471-040 CAP,E 10-50 K SME
C621 87-010-405-040 CAP,E 10-50 M 11L SME

C622 87-010-759-080 C-CAP,U, 0.1-25F
C623 87-012-188-080 C-CAP,U 47P-50 CH
C624 87-012-188-080 C-CAP,U 47P-50 CH
C625 87-012-188-080 C-CAP,U 47P-50 CH
C703 87-010-759-080 C-CAP,U, 0.1-25F

C704 87-010-759-080 C-CAP,U, 0.1-25F
C705 87-010-759-080 C-CAP,U, 0.1-25F
C706 87-010-759-080 C-CAP,U, 0.1-25F
C707 87-010-759-080 C-CAP,U, 0.1-25F
CN101 87-099-720-010 CONN,30P BLK TYK-B(P)

CN103 87-099-201-010 CONN,8P H BLK 6216
CN141 87-A60-667-010 CONN,3P H 2MM JMT
CN401 87-099-212-010 CONN,5P V BLK 6216
CN502 87-099-209-010 CONN,4P 6216H
CN603 87-A61-361-010 CONN,19P V GRY FMN-BTK

CN604 87-A61-385-010 CONN,21P H GRY FMN-SSTK
FFC103 88-908-451-110 FF-CABLE,8P 1.25 450MM
LED140 87-A40-266-080 LED,SLH-56VCT31 RED
LED672 87-A40-809-040 LED,LTL-307KK PGRN
LED673 87-A40-809-040 LED,LTL-307KK PGRN

LED674 87-A40-809-040 LED,LTL-307KK PGRN
LED675 87-A40-809-040 LED,LTL-307KK PGRN
LED676 87-A40-809-040 LED,LTL-307KK PGRN
LED677 87-A40-809-040 LED,LTL-307KK PGRN
S301 87-A90-095-080 SW,TACT EVQ11G04M

S302 87-A90-095-080 SW,TACT EVQ11G04M
S303 87-A90-095-080 SW,TACT EVQ11G04M
S304 87-A90-095-080 SW,TACT EVQ11G04M
SW162 87-A92-249-010 SW,RTRY EC12E24704-30MM
SW163 87-A92-113-010 SW,RTRY EC12E12504 30MM

X201 87-XMN-602-010 VIB,PIEZO PKM13EPY

LCD C.B

C151 87-A10-189-040 CAP,E 220-10
C154 87-A10-592-080 C-CAP,S 0.015-50 J B
C155 87-012-176-080 CAP 15P
C156 87-012-195-080 C-CAP,U 100P-50CH
C157 87-012-198-080 CAP 180P

C159 87-A10-353-080 C-CAP,U0.22-10KB
C165 87-012-336-080 C-CAP,U 330P-50 J SL
C166 87-010-075-040 CAP,E 10-16 5L
C170 87-010-759-080 C-CAP,U, 0.1-25F
C171 87-016-114-080 C-CAP,U0.01-25B

C172 87-010-759-080 C-CAP,U, 0.1-25F
C175 87-010-759-080 C-CAP,U, 0.1-25F
C176 87-012-274-080 CHIP CAP,U 1000P-50B
C177 87-010-194-080 CAP, CHIP 0.047
C180 87-010-759-080 C-CAP,U, 0.1-25F

C192 87-010-154-080 C-CAP,S 10P-50 D CH GRM
C193 87-018-209-080 CAP, TC U 0.1-50 Z F UP050
C195 87-A10-207-080 CAP, TC U 0.01-50 K B UP050
CN605 87-A61-361-010 CONN,19P V GRY FMN-BTK
CN606 87-A61-090-010 CONN,21P V GRY FMN-BTK

PART NO.

NO.

FB110 87-008-372-080 FILTER, EMI BL OIRNI
FC111 87-033-213-080 FUSE CLAMP, PFC5000
FC112 87-033-213-080 FUSE CLAMP, PFC5000
FFC605 8B-DJW-632-010 FF-CABLE,19P 1.0 220MM
FFC606 8B-DJW-631-010 FF-CABLE,21P 1.0 180MM

L151 87-A50-657-010 COIL,CLK 9.43MHZ (TOKO)7KLY
LCD101 8B-DJW-616-010 LCD,AIW4279-30P1N
LED691 87-A92-078-010 LED,SELU1D10CXM-SLF38 GR
LED692 87-A92-078-010 LED,SELU1D10CXM-SLF38 GR
LED693 87-A92-078-010 LED,SELU1D10CXM-SLF38 GR

PT C.B

C1 87-018-209-080 CAP, TC U 0.1-50Z F UP050
CN1 87-A61-110-010 CONN,9P V TID-A

!

F1 87-A91-219-010 FUSE,5A 250V T 50T

!

FC1 87-033-147-010 FUSE CLAMP,MT-20

!

FC2 87-033-147-010 FUSE CLAMP,MT-20

!

PT1 8B-NFW-602-010 PT,BNF-29 EZ

!

PT2 8B-MA6-675-010 PT,SUB BMA E (VRK)

!

RY2 87-A91-418-010 RELAY,AC12V G5PA-1-M

!

RY3 87-A91-418-010 RELAY,AC12V G5PA-1-M
T1 87-A60-317-010 TERMINAL, 1P MSC

!

!

T2 87-A60-317-010 TERMINAL, 1P MSC

!

W2 8A-AR3-651-010 CONN ASSY,2P AC-OUTLET

FAN C.B

C501 87-010-401-080 CAP,E 1-50 M 11L SME
C502 87-010-260-080 CAP,E 47-25 M 11L SME
C503 87-010-260-080 CAP,E 47-25 M 11L SME
CN502 87-099-553-010 CONN,4P H TUC-P
CN503 87-A60-619-010 CONN,2P V 2MM JMT

HP C.B

C261 87-010-176-080 C-CAP,S 680P-50 SL
C262 87-010-176-080 C-CAP,S 680P-50 SL
C263 87-012-368-080 C-CAP,S 0.1-50 F
CNA4 8B-NF8-653-010 CONN ASSY,5P TID-A (350)
J160 87-A61-480-010 JACK,DIA6.3 BLK ST W/SW MSC16A

R262 87-A00-440-050 RES,220-1/2W J RP
R263 87-A00-440-050 RES,220-1/2W J RP
R264 87-A00-440-050 RES,220-1/2W J RP
R265 87-A00-440-050 RES,220-1/2W J RP

MOT C.B

M401 87-045-305-010 MOTOR, RF-500TB

MIC C.B

C502 87-010-186-080 CAP,CHIP 4700P
C505 87-010-545-040 CAP,E 0.22-50 SME
C506 87-010-320-080 CHIP CAP 68P
C507 87-010-544-040 CAP,E 0.1-50 SME
C508 87-010-544-040 CAP,E 0.1-50 SME

C510 87-010-322-080 C-CAP,S 100P-50 CH
C511 87-A12-065-040 CAP,E 33-16 SMG
C512 87-010-178-080 CHIP CAP 1000P
C513 87-010-196-080 CHIP CAPACITOR,0.1-25
C514 87-010-196-080 CHIP CAPACITOR,0.1-25

C515 87-010-178-080 CHIP CAP 1000P
C516 87-012-140-080 C-CAP,S 470P-50 J CH
C520 87-010-178-080 CHIP CAP 1000P
CN552 87-A60-063-010 CONN,04P V 9604S-04C
FB501 87-008-372-080 FILTER, EMI BL OIRNI

J501 87-A61-243-010 JACK,6.3 BLK MONO W/SW V MSC
VR501 86-NFA-607-010 VR,RTRY 10K15AX1 1 V XV012PVN
W501 8B-NFW-636-010 TERMINAL ASSY,FASTON-ASSY

– 9 –

PART NO. DESCRIPTIONREF. NO. KANRI

NO.

KEY C.B

CNA3 88-803-033-010 CONN ASSY,3P 300MM
S321 87-A90-095-080 SW,TACT EVQ11G04M
S322 87-A90-095-080 SW,TACT EVQ11G04M
S323 87-A90-095-080 SW,TACT EVQ11G04M
S324 87-A90-095-080 SW,TACT EVQ11G04M

S325 87-A90-095-080 SW,TACT EVQ11G04M
S326 87-A90-095-080 SW,TACT EVQ11G04M
S327 87-A90-095-080 SW,TACT EVQ11G04M
S328 87-A90-095-080 SW,TACT EVQ11G04M
S341 87-A90-095-080 SW,TACT EVQ11G04M

S342 87-A90-095-080 SW,TACT EVQ11G04M
S343 87-A90-095-080 SW,TACT EVQ11G04M
S344 87-A90-095-080 SW,TACT EVQ11G04M
S345 87-A90-095-080 SW,TACT EVQ11G04M
S346 87-A90-095-080 SW,TACT EVQ11G04M

DESCRIPTIONREF. NO. KANRI

PART NO.

S347 87-A90-095-080 SW,TACT EVQ11G04M
S348 87-A90-095-080 SW,TACT EVQ11G04M
S349 87-A90-095-080 SW,TACT EVQ11G04M
S350 87-A90-095-080 SW,TACT EVQ11G04M
S351 87-A90-095-080 SW,TACT EVQ11G04M

S352 87-A90-095-080 SW,TACT EVQ11G04M

WIN C.B

CN402 87-A60-082-010 CONN,05P H 9604S-05F
CNA1 84-ZG1-647-010 CONN ASSY,2P
S401 87-A92-128-010 SW,LVR MXS01070MLBO

AC C.B

!

CN2 87-009-448-010 CONN,2P V VT

!

J2 87-009-932-010 OUTLET,AC E YKE31-0090

NO.

CHIP RESISTOR PART CODE

Chip Resistor Part Coding

88

A

Resistor Code

Chip resistor

Wattage Type Tolerance

1/16W 1005 5% CJ

1/16W

1/10W

1/8W

1608

2125

3216

5%

5%

5%

Symbol

CJ

CJ

CJ

Figure

Value of resistor

Form

L

Dimensions (mm)

t

W

LW t

1.0 0.5 0.35 104

1.6 0.8 0.45

2 1.25 0.45

3.2

1.6

Resistor Code

0.55

108

118

128

: A
: A

– 10 –

TRANSISTOR ILLUSTRATION

E C B

CSD655E
KTC3198GR

B C E

2SB1686
2SD2642

D

E C B

2SA1979O/Y
2SA1980G
2SC5342Y
CC5551

G D S

2SK2937

S

B C E

CSB1370EF

S D G

2SK2541

E C B

CSC4115BC

B

E

2SA1235F
2SC2714O
2SC3052F
CSD1306E
DTC144EKA
KRA102S

C

KRA107S
KRC107S
RT1N144C
RT1P141C
SBT5401F
SBT5551F

G

S

2SK2158

D

G

2SK360E

– 11 –

WIRING – 1 (MAIN / FAN / HP)

32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1

A

B

C

D

E

F

G

H

I

J

K

L

M

N

O

P

Q

– 12 –

R

S

T

U

SCHEMATIC DIAGRAM – 1 (MAIN 1 / 2 : AMP)

– 13 –

SCHEMATIC DIAGRAM – 2 (MAIN 2 / 2 : TUNER)

– 14 –