Aiwa XSG-5, XSG-3, XSG-4 Service manual

XS-G3

U,LH,EZ,K

XS-G4
XS-G5

EZ

EZ,K

SERVICE MANUAL

COMPACT DISC

STEREO SYSTEM

CD

CASSEIVER

XS–G3(U,LH) RC–BAS11CX–G3 SX–G3

• This Service Manual is the "Revision Publishing" and replaces "Simple Manual"

XS-G3 (U,LH,EZ,K) / XS-G4 (EZ) / XS-G5 (EZ,K), (S/M Code No. 09-012-441-5T1).

• If requiring information about the CD mechanisim, see Service Manual of BZG-5,
(S/M Code No. 09-00C-353-3N2)

BASIC TAPE MECHANISM : BZM-1 R1NM
BASIC CD MECHANISM : BZG-5 ZD3NM

SPEAKERSYSTEM

REMOTE

CONTROLLER

RC–BAS03XS–G3(EZ,K) CX–G3 SX–G3

RC–BAS11XS–G4(EZ) CX–G4 SX–G4

RC–BAS11XS–G5(EZ) CX–G5 SX–G5

RC–BAS03XS–G5(K) CX–G5 SX–G5

S/M Code No. 09-013-441-5R1

REVISION

DATA

SPECIFICATIONS

<FM tuner section>
Tuning range 87.5 MHz to 108 MHz
Usable sensitivity (IHF) EZ,K: 16.8 dBf

U,LH: 13.2 dBf

Antenna terminal 75 ohms (unbalanced)

<AM/MW tuner section>
Tuning range 531 kHz to 1602 kHz (9 kHz step)

530 kHz to 1710 kHz (10 kHz step)

Usable sensitivity 350 µV/m
Antenna Loop antenna

<LW tuner section><EZ,K>
Tuning range 144 kHz to 290 kHz
Usable sensitivity 1400 µV/m
Antenna Loop antenna

<Amplifier section>
Power output EZ,K:

Rated: 40 W + 40 W (6 ohms,
T.H.D. 1 %, 1 kHz/DIN45500)
Reference: 50 W + 50 W (6 ohms,
T.H.D. 10 %, 1 kHz/DIN45324)
EZ:
DIN MUSIC POWER: 121 W + 121 W
U: 60 W + 60 W (50 Hz – 20 kHz,
T.H.D. less than 1 %, 6 ohms)
75 W + 75 W (1 kHz, T.H.D. less than
10 %, 6 ohms)
LH:
Rated: 60 W + 60 W (6 ohms,
T.H.D. 1 %, 1 kHz)
Reference: 75 W + 75 W (6 ohms,
T.H.D. 10 %, 1 kHz)

Total harmonic distortion EZ,K:

0.08 % (25 W, 1 kHz, 6 ohms, DIN
AUDIO)
U,LH:

0.08 % (30 W, 1 kHz, 6 ohms, DIN
AUDIO)

Inputs VIDEO/AUX: 500 mV

LH ONLY: MIC: 1.7mV (10 kohms)

Output SPEAKERS: 6 ohms or more

PHONES: 32 ohms or more

<Cassette deck section>
Track format 4 tracks, 2 channels stereo
Frequency response 50 Hz – 15000 Hz
Recording system AC bias
Heads Recording/playback x 1, erase x 1

<Compact disc player section>
Laser Semiconductor laser (λ =780 nm)
D/A converter 1 bit dual
Signal-to-noise ratio 85 dB (1 kHz, 0 dB)
Harmonic distortion 0.05 % (1 kHz, 0 dB)

<Speaker system SX–G3 / SX–G4>
Speaker system 2 way, bass reflex (magnetic shielded)
Speaker units Woofer: 140 mm cone

Tweeter: 60 mm cone

Impedance 6 ohms
Dimensions (W x H x D) 165 x 328 x 225 mm
Weight 3.5 kg

<Speaker system SX–G5>
Speaker system 2 way, bass reflex (magnetic shielded)
Speaker units Woofer: 140 mm cone

Tweeter: 60 mm cone

Impedance 6 ohms
Dimensions (W x H x D) 170 x 328 x 268 mm
Weight 3.8 kg

<General>
Power requirements EZ,K: 230 V AC, 50 Hz

U: 120 V AC, 60 Hz
LH: 120 V / 220 – 230 V / 240 VAC
(Switchable), 50 Hz / 60 Hz

Power consumption U: 65 W

LH: 85 W
EZ: 70 W
K: 78 W

Power consumption With ECO mode on: 0.6 W
in standby mode U,EZ,K: With ECO mode off: 17 W

LH: With ECO mode off: 18 W

Dimensions of main unit U,EZ,K: 260 x 271.5 x 355 mm
(W x H x D) (101/4 x 103/4 x 14 in.)

LH: 260 x 271.5 x 364 mm

Dimensions (W x H x D) 260 x 301 x 292 mm
Weight U,EZ,K: 6.5 kg (14 lbs 5 oz)

LH: 6.8 kg

• Design and specifications are subject to change without notice.

• The word "BBE"and the "BBE symbol" are trademarks of BBE

Sound, Inc.

Under license from BBE Sound,Inc.

– 2 –

PROTECTION OF EYES FROM LASER BEAM DURING SERVICING

This set employs laser. Therefore, be sure to follow carefully
the instructions below when servicing.

WARNING!!

WHEN SERVICING, DO NOT APPROACH THE LASER
EXIT WITH THE EYE TOO CLOSELY. IN CASE IT IS
NECESSARY TO CONFIRM LASER BEAM EMISSION.
BE SURE TO OBSERVE FROM A DISTANCE OF MORE
THAN 30cm FROM THE SURFACE OF THE OBJEC­TIVE LENS ON THE OPTICAL PICK-UP BLOCK.

s Caution: Invisible laser radiation when

open and interlocks defeated avoid
exposure to beam.

s Advarsel: Usynlig laserståling ved åbning,

når sikkerhedsafbrydere er ude af funktion.
Undgå udsættelse for stråling.

VAROITUS!

Laiteen Käyttäminen muulla kuin tässä käyttöohjeessa
mainitulla tavalla saataa altistaa käyt-täjän
turvallisuusluokan 1 ylittävälle näkymättömälle
lasersäteilylle.

VARNING!

Om apparaten används på annat sätt än vad som
specificeras i denna bruksanvising, kan användaren
utsättas för osynling laserstrålning, som överskrider
gränsen för laserklass 1.

CAUTION

Use of controls or adjustments or performance of proce­dures other than those specified herin may result in
hazardous radiation exposure.

ATTENTION

L’utillisation de commandes, réglages ou procédures
autres que ceux spécifiés peut entraîner une dangereuse
exposition aux radiations.

ADVARSEL

Usynlig laserståling ved åbning, når sikkerhedsafbrydereer
ude af funktion. Undgå udsættelse for stråling.

This Compact Disc player is classified as a CLASS 1
LASER product.
The CLASS 1 LASER PRODUCT label is located on the
rear exterior.

CLASS 1 LASER PRODUCT
KLASSE 1 LASER PRODUKT
LUOKAN 1 LASER LAITE
KLASS 1 LASER APPARAT

Precaution to replace Optical block

(KSS-213F)

Body or clothes electrostatic potential could

ruin laser diode in the optical block. Be sure

ground body and workbench, and use care the

clothes do not touch the diode.

1) After the connection, remove solder shown in
right figure.

PICK-UP Assy PWB

Solder

– 3 –

NOTE ON BEFORE STARTING REPAIR

1. Forced discharge of electrolytic capacitor of power supply block

When repair is going to be attempted in the set that uses relay circuit in the power supply block, electric potential is kept charged across
the electrolytic capacitors (C101, 102) even though AC power cord is removed. If repair is attempted in this condition, secondary defect
can occur.
In order to prevent the secondary trouble, perform the following measures before starting repair work.

Discharge procedure

11

1 Remove the AC power cord.

11
22

2 Connect a discharging resistor at an end of lead wire that

22

has clips at both ends. Connect the other end of the lead
wire to metal chassis.

33

3 Contact the other end of the discharging resistor to the

33

positive (+) side (+VH) of C101. (For two seconds)

44

4 Contact the same end of the discharging resistor as step

44

33

3 to the negative (-) side (-VH) of C102 in the same way.

33

(For two seconds)

55

5 Check that voltage across C101 and C102 has decreased

55

to 1 V or less using a multimeter or an oscilloscope.

Select a discharging resistor referring to the following table.

Charging voltage (V) Discharging

(C101, 102) resistor (Ω)

25-48 100 3 87-A00-247-090

49-140 220 5 87-A00-232-090

Note: The reference numbers (C101, C102) of the electrolytic capacitors can change depending on the models. Be sure to check the

reference numbers of the charging capacitors on schematic diagram before starting the discharging work.

Rated power (W) Parts number

MAIN C.B

D101

3

C101 C102

22

Fig-1

4

2. Check items before exchanging the MICROCOMPUTER

Be sure to check the following items before exchanging the MICROCOMPUTER. Exchange the MICROCOMPUTER after confirming
that the MICROCOMPUTER is surely defective.

2-1. Regarding the HOLD terminal of the MICROCOMPUTER

When the HOLD terminal (INPUT) of the MICROCOMPUTER is “H”, the MICROCOMPUTER is judged to be operating correctly.
When this terminal is “L”, the main power cannot be turned on. Therefore, be sure to check the terminal voltage of the HOLD
terminal before exchange.
When the MICROCOMPUTER is not defective, the HOLD terminal can also go “L” when the POWER AMPLIFIER has any
abnormalities that triggers the abnormality detection circuit on the MAIN C. B. that sets the HOLD terminal to “L”.

• Good or no good judgement of the MICROCOMPUTER

11

1 Turn on the AC main power.

11
22

2 Confirm that the main power is turned on and the HOLD terminal of the MICROCOMPUTER keeps the “H” level or not.

22
33

3 When the HOLD terminal is “L” level, the abnormality detection circuit is judged to be working correctly and the

33

MICROCOMPUTER is judged to be good.

– 4 –

In such a case, check also if the POWER AMPLIFIER circuit or power supply circuit has any abnormalities or not.

2-2. Regarding reset

There are cases that the machine does not work correctly because the MICROCOMPUTER is not reset even though the AC power
cord is re-inserted, or the software reset (pressing the STOP key + POWER key) is performed.
When the above described phenomenon occurs, it can lead to wrong judgement as if the MICROCOMPUTER is defective and to
exchange the MICROCOMPUTER. In such a case, perform the forced-reset by the following procedure and check good or no
good of the MICROCOMPUTER.

11

1 Remove the AC power cord.

11

FRONT C.B

18

MICROCOMPUTER

FRONT C.B

22

2 Short both ends of the electrolytic capacitor C113 that is connected to VDD of the MICROCOMPUTER with tweezers.

22
33

3 Connect the AC power cord again. If the MICROCOMPUTER returns to the normal operation, the MICROCOMPUTER is

33

good.

Note: The reference number or MICROCOMPUTER pin number of transistor (Q110) and electrolytic capacitor (C113) can change depending

on the models. Be sure to check the reference numbers on schematic diagram before starting the discharging work.

15

C113

Short with tweezers.

Fig-2-2

C113

%

*

VSS

VDD

MICRO­COMPUTER

2-3. Confirmation of soldering state of MICROCOMPUTER

Check the soldering state of the MICROCOMPUTER in addition to the above described procedures. Be sure to exchange the
MICROCOMPUTER after surely confirming that the trouble is not caused by poor soldering but the MICROCOMPUTER itself.

– 5 –

DISASSEMBLY INSTRUCTIONS

1. DISASSEMBLY OF MECHANISM DECK ASSY

1) Remove the three screws.

2) Remove the three screws.

3) Remove the four screws (1) and remove the PANEL,
TOP (2).

4) Remove the PANEL, RIGHT.

– 6 –

5) Remove the PANEL, LEFT.

6) Remove the six screws (1) and remove the CABI, REAR
(2).

7) Remove the three FFCs (1), (2) (black) and (3), and
remove the connector (4).

8) Remove the three screws (1) and remove the PWB,
MAIN (2).

– 7 –

9) Slide up slightly the WINDOW, DISP ASSY (1).
Insert a thin flathead screwdriver into the slide groove
and disengage the detents of the WINDOW, DISP ASSY
(2) (in the left and right sides) and remove the WINDOW,
DISP ASSY.

10) Remove the two FFCs (1) and (2), and the four screws
(3) and remove the MECH DECK ASSSY (4).

11)Remove the two screws (1) and remove the HLDR,
WINDOW (2).

– 8 –

12) Remove the four screws (1) and remove the BZM-1 (2).

– 9 –

2. INSTRUCTIONS FOR ASSEMBLING MECHANISM
DECK ASSY

1) Install the BZM-1 and rotate the GEAR, RELAY

clockwise until the BOX, CASS cannot move any more.

2) Install the HLDR, WINDOW so that the upper end of the

HLDR, WINDOW and the upper end of the MECH ASSY
can be almost aligned to the same height.

3) Rotate the GEAR, RELAY until the HLDR, WINDOW

goes to the lowest part and stops.

– 10 –

PHASES ALIGNMENT

a

3) Mount GEAR, RELAY WINDOW
to put together b and c.

GEAR RELAY

* Mount in order.

1), 2), 3).
c

GEAR, RELAY WINDOW

a, b STEP

Join

1mm

b

2) APPL Y GREASE
(FG-87H)
BOTH SIDE of
the RIB.

*Align the position "b"
with position "c".

1) Turn GEAR RELAY until.
This LEVER is stopped.
(SEE a)

HDR,MECHA ASSY

a

1) Rotate the GEAR RELAY to open
the DECK.
Rotate it until it can rotate no more.

APPLY CFD-409 on the RAIL
(From top to BOTTOM)

a

2) Engage the gear so that the HDLR.
MECH ASSY comes to the same
height as the top (0 portion) of HLDR.
WINDOW.

JOIN with
RACK

b

b

HLDR, WINDOW

– 11 –

ELECTRICAL MAIN PARTS LIST

PART NO. DESCRIPTIONREF. NO. KANRI

NO.

IC

8B-NF8-645-010 C-IC,LC877256A-5V18<LH,U,K,3EZ>
8B-NF8-646-010 C-IC,LC877264V-5V24<4EZ,5EZ>
87-A21-831-010 IC,SPS-422-1-F1
87-A21-419-040 C-IC,NJM14558MD-TE2
87-A21-893-040 C-IC,NJM4558V-TE2

87-A21-401-040 C-IC,M61503FP
87-070-289-040 IC,BU2092F
87-A21-695-010 IC,LA1845L
87-A20-440-040 C-IC,BU1920FS<5EZ,4EZ>
87-A21-928-010 IC,LC72131D-N

87-020-454-010 IC,DN6851

TRANSISTOR

87-A30-559-010 TR,CSB1370EF
87-A30-492-080 TR,2SC5343G
87-A30-076-080 C-TR,2SC3052F
87-A30-075-080 C-TR,2SA1235F
87-A30-494-080 TR,2SA1980G

87-A30-107-070 C-TR,CMBT5401
87-A30-484-080 C-TR,KRA102S
87-A30-190-080 TR,CC5551
87-A30-106-040 C-TR,CMBT5551
87-A30-306-010 TR,2SB1677<EZ,K>

87-A30-528-010 TR,2SB1686<LH,U>
87-A30-307-010 TR,2SD2619<EZ,K>
87-A30-529-010 TR,2SD2642<LH,U>
87-A30-490-080 C-TR,KRC107S
87-A30-162-010 FET,2SK2937

87-A30-582-080 TR,CDA1585BC
87-A30-495-080 TR,2SA1981Y
87-A30-468-080 C-TR,KRC102S-RTK
87-A30-091-080 FET,2SJ460
87-A30-062-080 C-TR,KRC104S

87-A30-063-080 C-TR,KRA104S
87-A30-520-080 TR,2SC5342Y
87-A30-515-080 TR,2SA1979O/Y
87-A30-087-080 C-FET,2SK2158
87-A30-090-080 FET,2SK2541

89-327-143-080 C-TR,2SC2714O
87-A30-489-080 C-TR,KRA107S
89-503-602-080 C-FET,2SK360E
87-A30-086-040 C-TR,CSD1306E<EZ,K>
87-A30-234-080 TR,CSC4115BC

DIODE

87-A40-393-090 DIODE,1N5402GW(F20)
87-A40-291-080 DIODE,1N4148M(CPT)
87-A40-455-090 DIODE,RL203 GW<EZ,K>
87-A40-764-080 ZENER,UZ10BSC
87-A40-553-080 DIODE,1N4003 LES

87-A40-270-080 C-DIODE,MC2838
87-A40-269-080 C-DIODE,MC2836
87-A40-488-080 DIODE,1SS244<LH>
87-A40-748-080 ZENER,UZ5.6BSA
87-A40-002-080 ZENER,MTZJ5.1C<U,EZ,K>

87-A40-747-080 ZENER,UZ5.1BSB<LH>
87-A40-749-080 ZENER,UZ5.6BSB
87-A40-739-080 ZENER,UZ2.7BSA
87-017-149-080 ZENER,HZS6A2L

MAIN C.B

C3 87-012-368-080 C-CAP,S 0.1-50 F
C4 87-012-368-080 C-CAP,S 0.1-50 F
C5 87-012-368-080 C-CAP,S 0.1-50 F
C6 87-012-368-080 C-CAP,S 0.1-50 F
C9 87-010-759-080 C-CAP,U, 0.1-25F<U,EZ,K>

DESCRIPTIONREF. NO. KANRI

PART NO.

NO.

C9 87-010-196-080 CHIP CAPACITOR,0.1-25<LH>
C10 87-010-759-080 C-CAP,U, 0.1-25F<U,EZ,K>
C10 87-010-196-080 CHIP CAPACITOR,0.1-25<LH>
C11 87-010-759-080 C-CAP,U, 0.1-25F<U,EZ,K>
C11 87-010-196-080 CHIP CAPACITOR,0.1-25<LH>

C12 87-010-759-080 C-CAP,U, 0.1-25F<U,EZ,K>
C12 87-010-196-080 CHIP CAPACITOR,0.1-25<LH>
C19 87-A12-776-090 CAP,E 2200-50 M 85 SKR<EZ,K>
C19 87-A12-382-000 CAP,E 2200-63 M 85 IV LELON<LH,U>
C19 87-A12-779-090 CAP,E 3300-50 M 85 KR<EZ>

C20 87-A12-776-090 CAP,E 2200-50 M 85 SKR<K>
C20 87-A12-779-090 CAP,E 3300-50 M 85 KR<EZ>
C20 87-A12-382-000 CAP,E 2200-63 M 85 IV LELON<LH,U>
C21 87-A12-777-090 CAP,E 3300-25 M 85 SKR<K>
C21 87-A12-782-090 CAP,E 4700-25 M 85 SKR<EZ>

C21 87-A12-778-090 CAP,E 3300-35 M 85 SKR<LH,U>
C22 87-A12-777-090 CAP,E 3300-25 M 85 SKR<EZ,K>
C22 87-A12-778-090 CAP,E 3300-35 M 85 SKR<LH,U>
C32 87-010-197-080 CAP, CHIP 0.01 DM<LH>
C32 87-012-286-080 CAP, U 0.01-25<U,EZ,K>

C33 87-A12-062-080 CAP,E 100-10 SMG<U>
C34 87-A12-072-080 CAP,E 100-25 SMG
C35 87-A12-071-080 CAP,E 47-25 SMG<LH,U,K>
C35 87-A12-090-080 CAP,E 4.7-50 SMG<EZ>
C36 87-A12-066-080 CAP,E 47-16 SMG<EZ>

C36 87-A12-067-080 CAP,E 330-16 SMG<LH,U,K>
C38 87-010-197-080 CAP, CHIP 0.01 DM<LH>
C38 87-012-286-080 CAP, U 0.01-25<U,EZ,K>
C60 87-A12-089-080 CAP,E 3.3-50 SMG
C61 87-A12-071-080 CAP,E 47-25 SMG

C83 87-A12-074-080 CAP,E 470-25 SMG
C97 87-010-831-080 C-CAP,U,0.1-16F
C101 87-012-279-080 C-CAP,U 2700P-50 B
C102 87-012-279-080 C-CAP,U 2700P-50 B
C103 87-A12-084-080 CAP,E 0.22-50 SMG

C104 87-A12-084-080 CAP,E 0.22-50 SMG
C105 87-012-277-080 C-CAP, U 1800P-50 B
C106 87-012-277-080 C-CAP, U 1800P-50 B<LH,U,K>
C107 87-A12-089-080 CAP,E 3.3-50 SMG
C108 87-A12-089-080 CAP,E 3.3-50 SMG

C109 87-012-195-080 C-CAP,U 100P-50CH<EZ,K>
C110 87-012-195-080 C-CAP,U 100P-50CH<EZ,K>
C111 87-A12-077-080 CAP,E 33-35 SMG
C112 87-A12-077-080 CAP,E 33-35 SMG
C113 87-A10-596-080 C-CAP,S 100P-100 J CH

C114 87-A10-596-080 C-CAP,S 100P-100 J CH
C117 87-012-368-080 C-CAP,S 0.1-50 F
C118 87-012-368-080 C-CAP,S 0.1-50 F
C119 87-012-286-080 CAP, U 0.01-25
C120 87-012-286-080 CAP, U 0.01-25

C123 87-010-177-080 C-CAP,S 820P-50 SL
C124 87-010-177-080 C-CAP,S 820P-50 SL
C133 87-012-282-080 CAP, U 4700P-50
C140 87-012-278-080 C-CAP,U 2200P-50 B
C186 87-010-759-080 C-CAP,U, 0.1-25F

C187 87-A12-091-080 CAP,E 10-50 SMG
C188 87-A12-091-080 CAP,E 10-50 SMG
C225 87-012-368-080 C-CAP,S 0.1-50 F
C226 87-012-368-080 C-CAP,S 0.1-50 F
C227 87-012-368-080 C-CAP,S 0.1-50 F

C228 87-012-368-080 C-CAP,S 0.1-50 F
C229 87-010-191-080 C-CAP,S 0.015-50 F<EZ,K>
C230 87-010-191-080 C-CAP,S 0.015-50 F<EZ,K>
C231 87-012-286-080 CAP, U 0.01-25<EZ,K>
C232 87-012-286-080 CAP, U 0.01-25<EZ,K>

C303 87-012-275-080 C-CAP,U 1200P-50 B
C304 87-012-275-080 C-CAP,U 1200P-50 B
C307 87-A12-062-080 CAP,E 100-10 SMG
C308 87-A12-062-080 CAP,E 100-10 SMG
C309 87-012-188-080 C-CAP,U 47P-50 CH

– 12 –

PART NO. DESCRIPTIONREF. NO. KANRI

NO.

C310 87-012-188-080 C-CAP,U 47P-50 CH
C313 87-012-284-080 CAP, U 6800P-50
C314 87-012-284-080 CAP, U 6800P-50
C315 87-A12-062-080 CAP,E 100-10 SMG
C317 87-A12-085-080 CAP,E 0.33-50 SMG

C318 87-A12-085-080 CAP,E 0.33-50 SMG
C326 87-010-787-080 CAP, U 0.022-25
C327 87-010-831-080 C-CAP,U,0.1-16F
C350 87-012-286-080 CAP, U 0.01-25<EZ,K>
C360 87-A12-087-080 CAP,E 1-50 SMG

C399 87-A10-039-080 C-CAP,U 470P-50 J CH<U,EZ,K>
C399 87-012-140-080 CAP 470P<LH>
C401 87-A12-083-080 CAP,E 0.1-50 SMG
C402 87-A12-083-080 CAP,E 0.1-50 SMG
C403 87-012-193-080 C-CAP,U 82P-50 CH

C404 87-012-193-080 C-CAP,U 82P-50 CH
C405 87-012-286-080 CAP, U 0.01-25
C406 87-012-286-080 CAP, U 0.01-25
C407 87-012-286-080 CAP, U 0.01-25
C408 87-012-286-080 CAP, U 0.01-25

C409 87-012-278-080 C-CAP,U 2200P-50 B
C410 87-012-278-080 C-CAP,U 2200P-50 B
C411 87-A12-091-080 CAP,E 10-50 SMG
C412 87-A12-091-080 CAP,E 10-50 SMG
C452 87-A12-069-080 CAP,E 22-25 SMG

C453 87-012-279-080 C-CAP,U 2700P-50 B
C454 87-012-279-080 C-CAP,U 2700P-50 B
C455 87-012-279-080 C-CAP,U 2700P-50 B
C456 87-012-286-080 CAP, U 0.01-25
C457 87-A12-361-080 CAP,M 5600P-100 J CP

C458 87-012-274-080 CHIP CAP,U 1000P-50B
C459 87-012-271-080 CAP, U 560P-50
C460 87-010-831-080 C-CAP,U,0.1-16F
C461 87-012-158-080 C-CAP,S 390P-50 CH
C462 87-012-158-080 C-CAP,S 390P-50 CH

C470 87-018-127-080 CAP, CER 470P-50V
C605 87-012-280-080 CAP, U 3300P-50
C606 87-012-280-080 CAP, U 3300P-50
C609 87-010-785-080 C-CAP,U0.015-25BK
C610 87-010-785-080 C-CAP,U0.015-25BK

C611 87-A12-084-080 CAP,E 0.22-50 SMG
C612 87-A12-084-080 CAP,E 0.22-50 SMG
C613 87-A12-084-080 CAP,E 0.22-50 SMG
C614 87-A12-084-080 CAP,E 0.22-50 SMG
C615 87-012-172-080 CAPACITOR CHIP U 10P CH

C616 87-010-221-080 CAP, ELECT 470-10V
C617 87-010-221-080 CAP, ELECT 470-10V
C618 87-A12-091-080 CAP,E 10-50 SMG
C620 87-A12-062-080 CAP,E 100-10 SMG
C623 87-A12-084-080 CAP, ELECT 0.22-50 SMG<EZ>

C623 87-010-401-080 CAP, ELECT 1-50V<LH,U,K>
C624 87-A12-084-080 CAP, ELECT 0.22-50 SMG<EZ>
C624 87-010-401-080 CAP, ELECT 1-50V<LH,U,K>
C630 87-A10-260-080 C-CAP,U 0.1-16 K B
C631 87-012-281-080 C-CAP,U 3900P-50 B

C632 87-012-281-080 C-CAP,U 3900P-50 B
C633 87-A11-070-080 C-CAP,U 0.033-16 K B
C634 87-A11-070-080 C-CAP,U 0.033-16 K B
C661 87-012-336-080 C-CAP,U 330P-50J SL
C662 87-012-336-080 C-CAP,U 330P-50J SL

C669 87-012-274-080 CHIP CAP,U 1000P-50B<U,EZ,K>
C670 87-012-274-080 CHIP CAP,U 1000P-50B<U,EZ,K>
C671 87-010-759-080 C-CAP,U, 0.1-25F<LH>
C672 87-010-759-080 C-CAP,U, 0.1-25F<LH>
C673 87-012-278-080 C-CAP,U 2200P-50 B<LH>

C677 87-012-286-080 CAP, U 0.01-25
C771 87-A12-062-080 CAP,E 100-10 SMG
C772 87-012-286-080 CAP, U 0.01-25
C779 87-010-949-080 C-CAP,S 0.01-50 BJ<EZ,K>
C780 87-010-949-080 C-CAP,S 0.01-50 BJ<EZ,K>

DESCRIPTIONREF. NO. KANRI

PART NO.

NO.

C782 87-012-286-080 CAP, U 0.01-25
C783 87-012-286-080 CAP, U 0.01-25
C784 87-012-286-080 CAP, U 0.01-25
C785 87-012-286-080 CAP, U 0.01-25
C786 87-012-286-080 CAP, U 0.01-25

C788 87-012-167-080 C-CAP,U 5P-50 CH
C789 87-A12-052-080 C-CAP,S 0.033-25 J B<LH,U>
C789 87-016-118-080 C-CAP,U0.022-25BJ<EZ,K>
C790 87-A12-052-080 C-CAP,S 0.033-25 J B<LH,U>
C790 87-016-118-080 C-CAP,U0.022-25BJ<EZ,K>

C791 87-010-831-080 C-CAP,U,0.1-16F
C792 87-012-286-080 CAP, U 0.01-25
C793 87-A12-090-080 CAP,E 4.7-50 SMG
C795 87-012-286-080 CAP, U 0.01-25
C796 87-012-286-080 CAP, U 0.01-25

C797 87-A12-091-080 CAP,E 10-50 SMG
C798 87-012-286-080 CAP, U 0.01-25
C799 87-010-265-080 CAP, ELECT 33-16V
C800 87-010-829-080 CAP, U 0.047-16
C801 87-A12-089-080 CAP,E 3.3-50 SMG

C802 87-010-829-080 CAP, U 0.047-16
C803 87-010-787-080 CAP, U 0.022-25
C804 87-A12-062-080 CAP,E 100-10 SMG
C807 87-A12-086-080 CAP,E 0.47-50 SMG
C808 87-A12-087-080 CAP,E 1-50 SMG

C809 87-A12-087-080 CAP,E 1-50 SMG
C810 87-010-831-080 C-CAP,U,0.1-16F
C814 87-012-286-080 CAP, U 0.01-25
C815 87-A12-086-080 CAP,E 0.47-50 SMG
C816 87-A12-086-080 CAP,E 0.47-50 SMG

C818 87-012-276-080 CAP, CHIP SS 1500 PBK<EZ,K>
C821 87-A12-091-080 CAP,E 10-50 SMG
C823 87-010-177-080 C-CAP,S 820P-50 SL<LH,U>
C823 87-A10-915-080 C-CAP,U 1000P-25 J CH<EZ,K>
C824 87-A12-090-080 CAP,E 4.7-50 SMG

C825 87-010-596-080 CAP, S 0.047-16
C831 87-A12-092-080 CAP,E 22-50 SMG<EZ,K>
C842 87-012-286-080 CAP, U 0.01-25
C844 87-012-286-080 CAP, U 0.01-25
C850 87-A12-071-080 CAP,E 47-25 SMG

C851 87-012-286-080 CAP, U 0.01-25
C852 87-012-286-080 CAP, U 0.01-25
C853 87-012-286-080 CAP, U 0.01-25
C858 87-010-831-080 C-CAP,U,0.1-16F
C859 87-010-831-080 C-CAP,U,0.1-16F<EZ,K>

C860 87-012-286-080 CAP, U 0.01-25<EZ,K>
C869 87-012-286-080 C-CAP,U, 0.01-25<5EZ,4EZ>
C870 87-012-274-080 C-CAP,U, 1000P-50<5EZ,4EZ>
C871 87-012-199-080 C-CAP,U, 220P-50<5EZ,4EZ>
C872 87-012-199-080 C-CAP,U, 220P-50<5EZ,4EZ>

C873 87-A10-039-080 C-CAP,U, 470P-50<5EZ,4EZ>
C874 87-A12-091-080 CAP, ELECT 10-50 SMG<5EZ,4EZ>
C875 87-010-759-080 C-CAP,U, 0.1-25F<5EZ,4EZ>
C876 87-A12-091-080 CAP, ELECT 10-50 SMG<5EZ,4EZ>
C877 87-012-286-080 C-CAP,U, 0.01-25<5EZ,4EZ>

C878 87-012-184-080 C-CAP,U, 33P-50<5EZ,4EZ>
C879 87-012-180-080 C-CAP,U, 22P-50<5EZ,4EZ>
C901 87-018-145-080 CAP,TC-U 6.8P-50 CH<LH,U>
C904 87-012-286-080 CAP, U 0.01-25<LH,U>
C905 87-012-286-080 CAP, U 0.01-25<LH,U>

C907 87-012-286-080 CAP, U 0.01-25<LH,U>
C908 87-A10-915-080 C-CAP,U 1000P-25 J CH<LH,U>
C909 87-012-286-080 CAP, U 0.01-25<LH,U>
C910 87-012-174-080 CAP CHIP CERA SS 12P CHJ<LH,U>
C911 87-012-170-080 C-CAP,U 8P-50 CH<LH,U>

C912 87-012-195-080 C-CAP,U 100P-50CH<LH,U>
C913 87-012-286-080 CAP, U 0.01-25<LH,U>
C914 87-012-166-080 C-CAP,U 4P-50 CH<LH,U>
C915 87-012-174-080 CAP CHIP CERA SS 12P CHJ<LH,U>
C916 87-012-180-080 C-CAP,U 22P-50 CH<LH,U>

– 13 –

PART NO. DESCRIPTIONREF. NO. KANRI

NO.

C917 87-012-186-080 C-CAP,U 39P-50 CH<LH,U>
C918 87-A10-039-080 C-CAP,U 470P-50 J CH<LH,U>
C921 87-012-195-080 C-CAP,U 100P-50CH<LH,U>
C922 87-012-174-080 CAP CHIP CERA SS 12P CHJ<LH,U>
C940 87-012-286-080 CAP, U 0.01-25<EZ,K>

C942 87-012-165-080 CAP 3P-50<EZ,K>
C947 87-012-286-080 CAP, U 0.01-25<EZ,K>
C948 87-A10-039-080 C-CAP,U 470P-50 J CH<EZ,K>
C952 87-012-286-080 CAP, U 0.01-25<EZ,K>
C957 87-012-174-080 C-CAP CERA SS 12P CHJ<EZ,K>

C958 87-012-286-080 CAP, U 0.01-25<EZ,K>
C959 87-010-831-080 C-CAP,U,0.1-16F
C960 87-010-831-080 C-CAP,U,0.1-16F
C961 87-012-167-080 C-CAP,U 5P-50 CH<LH,U>
C962 87-A12-087-080 CAP,E 1-50 SMG<EZ,K>

C963 87-015-785-080 CHIP CAPACITOR, 0.1FZ-25Z
C971 87-A12-067-080 CAP,E 330-16 SMG
C972 87-A12-090-080 CAP,E 4.7-50 SMG
C973 87-012-286-080 CAP, U 0.01-25
C974 87-012-286-080 CAP, U 0.01-25

C979 87-012-195-080 C-CAP,U 100P-50CH
C981 87-A12-071-080 CAP,E 47-25 SMG
C982 87-010-831-080 C-CAP,U,0.1-16F
C983 87-012-286-080 CAP, U 0.01-25
C984 87-012-286-080 CAP, U 0.01-25

C985 87-012-195-080 C-CAP,U 100P-50CH<EZ,K>
C987 87-012-286-080 CAP, U 0.01-25
C989 87-012-286-080 CAP, U 0.01-25<EZ,K>
C991 87-012-176-080 CAP 15P
C992 87-012-176-080 CAP 15P

C993 87-012-274-080 CHIP CAP,U 1000P-50B
C995 87-012-274-080 CHIP CAP,U 1000P-50B
C997 87-010-831-080 C-CAP,U,0.1-16F
C998 87-A12-071-080 CAP,E 47-25 SMG
C999 87-A11-155-080 CAP,TC U 0.01-16 Z F

CF831 87-008-261-010 FILTER, SFE10.7MA5<LH,U>
CF831 87-008-423-010 FLTR,CF,SFE10.7MS3G-A<EZ,K>
CF832 82-785-747-010 CF MS2 GHY R<EZ,K>
CF832 87-008-261-010 FLTR,CF,SFE10.7MA5<LH,U>
CN351 87-A60-625-010 CONN,8P V 2MM JMT

CN501 87-099-564-010 CONN,4PVTUC-P4P-B1<LH>
CN601 87-099-750-010 CONN,15P V 9604SC
CN602 87-A60-131-010 CONN,6P V FE
CN605 87-A61-108-010 CONN,5P V TID-A
CN607 87-099-017-010 CONN, 15P V BLK 6216

CNA1 8B-NF8-652-010 CONN ASSY,7P TID-A(300)<LH>
D902 87-A40-128-080 C-VARI-CAP,HVU202A<LH,U>
D903 87-A40-128-080 C-VARI-CAP,HVU202A<LH,U>
FFC602 88-906-401-110 FF-CABLE,6P 1.25
FFE831 A8-6ZA-19H-030 6ZA-1 FEMENM<EZ,K>

J203 87-A60-238-010 TERMINAL,SP 4P (MSC)
J602 87-A60-881-010 JACK,PIN 2P MSP 242V05 PBSN
J831 87-A60-202-010 TERMINAL,ANT 4P<LH,U>
J832 87-A60-403-010 TERMINAL,ANT PAL 2P<EZ,K>
JR123 87-A10-596-080 C-CAP,S 100P-100 J CH

JR124 87-A10-596-080 C-CAP,S 100P-100 J CH
L201 87-A50-610-010 COIL,1UH K(MDEC)
L202 87-A50-610-010 COIL,1UH K(MDEC)
L451 87-007-342-010 COIL,OSC 85KHZ BIAS
L801 87-A50-608-010 COIL,FM DET-N(TOK)

L802 87-A91-551-010 FLTR,PCFJZH-450 L(TOK)
L811 87-005-847-080 COIL,2.2UH K CECS
L832 87-005-847-080 COIL,2.2UH K CECS
L861 87-005-847-080 COIL,2.2UH K CECS<5EZ,4EZ>
L902 88-ZA1-602-110 COIL,FM-RF-U2 2G<LH,U>

L903 88-ZA1-601-010 COIL,FM-RF-U1 2G<LH,U>
L904 87-005-847-080 COIL,2.2UH(CECS)<LH,U>
L905 88-ZA1-624-010 COIL,FM IFT 7-6.2 (COILS)<LH,U>
L906 88-ZA1-603-010 COIL,FM-OSC-U 2G<LH,U>
L941 87-A50-020-010 COIL,ANT LW(COI)252KHZ<EZ,K>

DESCRIPTIONREF. NO. KANRI

PART NO.

NO.

L942 87-A50-019-010 COIL,OSC LW(COI)856KHZ<EZ,K>
L951 8A-NF8-668-010 COIL,AM PACK 2(TOK)<EZ,K>
L951 8A-NF8-667-010 COIL,AM PACK 4(TOK)<LH,U>
R129 87-A00-257-080 RES,M/F 0.15-1W J<U,EZ,K>
R129 87-A00-262-080 RES,M/F 0.15-2W J<LH>

R130 87-A00-257-080 RES,M/F 0.15-1W J<U,EZ,K>
R130 87-A00-262-080 RES,M/F 0.15-2W J<LH>
R131 87-A00-257-080 RES,M/F 0.15-1W J<U,EZ,K>
R131 87-A00-262-080 RES,M/F 0.15-2W J<LH>
R132 87-A00-257-080 RES,M/F 0.15-1W J<U,EZ,K>

R132 87-A00-262-080 RES,M/F 0.15-2W J<LH>
R790 87-012-286-080 CAP, U 0.01-25
R991 87-012-195-080 C-CAP,U 100P-50CH
R993 87-012-195-080 C-CAP,U 100P-50CH
R995 87-012-195-080 C-CAP,U 100P-50CH

SFR451 87-A90-432-080 SFR,30K H NVZ6TLTA
SFR452 87-A90-432-080 SFR,30K H NVZ6TLTA
TC942 87-A91-774-080 TRIMMER,PLY30P 6.8X5.4CDYL<EZ,K>
TH101 87-A91-042-080 C-THMS,100K 55001
TH102 87-A91-042-080 C-THMS,100K 55001

W99 8B-NF8-656-010 F-CABLE,7P 2.5 250MM<U,EZ,K>
WH1 87-A90-510-010 HLDR,WIRE 2.5-9P
X862 87-A70-307-010 VIB,XTAL 4.332MHZ CSA-309ST<5EZ,4EZ>
X992 87-A70-306-010 VIB,XTAL 4.500MHZ CSA-309ST

FRONT C.B

C141 87-012-278-080 C-CAP,U 2200P-50 B
C151 87-A10-189-040 CAP,E 220-10
C153 87-A10-353-080 C-CAP,U 0.22-10KB
C154 87-010-785-080 C-CAP,U0.015-25BK
C155 87-012-176-080 CAP 15P

C156 87-012-195-080 C-CAP,U 100P-50CH
C157 87-012-198-080 CAP 180P
C165 87-012-268-080 C-CAP,U 330P-50 B
C166 87-010-075-040 CAP,E 10-16 5L
C170 87-010-759-080 C-CAP,U, 0.1-25F

C171 87-016-114-080 C-CAP,U0.01-25B
C175 87-010-759-080 C-CAP,U, 0.1-25F
C176 87-012-274-080 CHIP CAP,U 1000P-50B
C177 87-010-757-080 C.CAP,U 0.047-25F
C180 87-010-759-080 C-CAP,U, 0.1-25F

C193 87-012-271-080 CAP, U 560P-50
C194 87-012-195-080 C-CAP,U 100P-50CH
C315 87-010-759-080 C-CAP,U, 0.1-25F
C441 87-010-412-040 CAP,E 10-25 5L
C451 87-010-067-040 CAP,E 0.1-50 5L

C452 87-010-421-040 CAP,E 4.7-50 5L
C453 87-010-788-080 C-CAP,U 0.033-2.5F
C454 87-012-273-080 C-CAP,U 820P-50 B
C456 87-010-785-080 C-CAP,U0.015-25BK
C457 87-012-280-080 CAP, U 3300P-50

C459 87-A10-025-080 C-CAP,U, 0.22-16ZF
C460 87-010-831-080 C-CAP,U,0.1-16F
C621 87-010-075-040 CAP,E 10-16 5L
C622 87-010-759-080 C-CAP,U, 0.1-25F
C623 87-012-188-080 C-CAP,U 47P-50 CH

C624 87-012-188-080 C-CAP,U 47P-50 CH
C625 87-012-188-080 C-CAP,U 47P-50 CH
C679 87-010-759-080 C-CAP,U, 0.1-25F
C689 87-010-759-080 C-CAP,U, 0.1-25F
CN101 87-099-750-010 CONN,15P V 9604SC

CN102 87-099-017-010 CONN, 15P 6216
CN103 87-099-196-010 CONN,8P 6216
CN121 87-A60-131-010 CONN,6P V FE
CN251 87-A60-133-010 CONN,8P V FE
CN401 87-A60-130-010 CONN,5P V FE

CN501 87-A60-586-010 CONN,4P V FE<LH>
CNA141 8B-NF8-650-010 CONN ASSY,2P (35)
FFC101 88-915-151-110 FF-CABLE,15P 1.25 150MM

– 14 –

PART NO. DESCRIPTIONREF. NO. KANRI

DESCRIPTIONREF. NO. KANRI

NO.

FFC102 8B-NF8-655-010 FF-CABLE,15P 1.25 150MM BLACK
FFC103 88-908-451-110 FF-CABLE,8P 1.25 450MM
FFC121 88-906-081-110 FF-CABLE,6P 1.25 80MM
FFC251 88-908-451-110 FF-CABLE,8P 1.25 450MM
FFC401 88-905-331-110 FF-CABLE,5P 1.25 330MM

FFC501 88-904-351-110 FF-CABLE,4P 1.25<LH>
L151 87-A50-657-010 COIL,CLK 9.43MHZ (TOKO)7KLY
LCD101 8B-NF8-601-010 LCD,AIW4272-30P1N
LED140 87-A40-317-080 LED,SLR-342VCT31 RED
LED671 87-A41-053-010 LED,SMLU18D16CGREEN/UMBER<K,3EZ>

LED671 87-A92-077-010 LED,SMLU1BE16C-SLF73BLU/UMB<EXCEPT 3EZ,K>
LED681 87-A41-053-010 LED,SMLU18D16CGREEN/UMBER<K,3EZ>
LED681 87-A92-077-010 LED,SMLU1BE16C-SLF73BLU/UMB<EXCEPT 3EZ,K>
R192 87-010-785-080 C-CAP,U0.015-25KB GRM
R193 87-010-785-080 C-CAP,U0.015-25KB GRM

R194 87-010-785-080 C-CAP,U0.015-25KB GRM
S306 87-A90-095-080 SW,TACT EVQ11G04M
S307 87-A90-095-080 SW,TACT EVQ11G04M
S308 87-A90-095-080 SW,TACT EVQ11G04M<5EZ,4EZ>
S309 87-A90-095-080 SW,TACT EVQ11G04M<5EZ,4EZ>

S310 87-A90-095-080 SW,TACT EVQ11G04M<5EZ,4EZ>
S341 87-A90-095-080 SW,TACT EVQ11G04M
S342 87-A90-095-080 SW,TACT EVQ11G04M
S343 87-A90-095-080 SW,TACT EVQ11G04M
S344 87-A90-095-080 SW,TACT EVQ11G04M

S345 87-A90-095-080 SW,TACT EVQ11G04M
S346 87-A90-095-080 SW,TACT EVQ11G04M
S347 87-A90-095-080 SW,TACT EVQ11G04M
S348 87-A90-095-080 SW,TACT EVQ11G04M
S349 87-A90-095-080 SW,TACT EVQ11G04M

SW162 87-A92-172-010 SW,RTRY EC12E24204-25MM OFF<LH,U,K>
SW162 87-A91-645-010 SW,RTRY EC12E24304NON-CLICK<EZ>

PT C.B

C85 87-010-831-080 C-CAP,U,0.1-16F<EZ,K>
CN1 87-A61-109-010 CONN,7P V TID-A<LH>

!

PT1 8B-NF8-608-010 PT,BNF8-EZK<EZ,K>

!

PT1 8B-NF8-606-010 PT,BNF8-LH<LH>

!

PT1 8B-NF8-607-010 PT,BNF8-U<U>

!

PT2 8B-MA6-673-010 PT,SUB BMA H (VRK)<LH>

!

PT81 8B-MA6-675-010 PT,SUB BMA E (VRK)<EZ,K>

!

PT81 8B-MA6-671-010 PT,SUB BMA U (VRK)<U>

!

RY1 87-A92-058-010 RELAY,AC DC12V HRM4-S<LH>

!

RY81 87-A92-072-010 RELAY,AC DC12V HRM3H-S-1POLE<U>

!

RY81 87-A91-418-010 RELAY,AC12V G5PA-1-M<EZ,K>

!

S1 87-A90-165-010 SW,SL 1-2-3 SWS2301<LH>

!

T1 87-A60-317-010 TERMINAL, 1P MSC<LH>

!

T2 87-A60-317-010 TERMINAL, 1P MSC<LH>

!

T81 87-A60-317-010 TERMINAL, 1P MSC<U,EZ,K>

!

T82 87-A60-317-010 TERMINAL, 1P MSC<U,EZ,K>
WH81 87-A90-460-010 HLDR,WIRE 2.5-7P<U,EZ,K>

JACK C.B

C223 87-010-176-080 C-CAP,S 680P-50 SL<EZ,K>
C224 87-010-176-080 C-CAP,S 680P-50 SL<EZ,K>
C241 87-010-831-080 C-CAP,U,0.1-16F
CNA5 8B-NF8-653-010 CONN ASSY,5P TID-A (600)
J201 87-A61-480-010 JACK,DIA6.3 BLK ST W/SW MSC16A

R243 87-A01-001-050 RES,220-1/2W J BLT2J<EZ>
R243 87-A00-440-050 RES,220-1/2W J RP<LH,U,K>
R244 87-A00-440-050 RES,220-1/2W J RP<LH,U,K>
R244 87-A01-001-050 RES,220-1/2W J BLT2J<EZ>
R245 87-A00-439-050 RES,180-1/2W J RP<K>

R245 87-A00-440-050 RES,220-1/2W J RP<U>
R245 87-A00-441-050 RES,270-1/2W J RP<LH>
R245 87-A01-001-050 RES,220-1/2W J BLT2J<EZ>
R246 87-A01-001-050 RES,220-1/2W J BLT2J<EZ>
R246 87-A00-439-050 RES,180-1/2W J RP<K>

PART NO.

NO.

R246 87-A00-440-050 RES,220-1/2W J RP<U>
R246 87-A00-441-050 RES,270-1/2W J RP<LH>
WH2 87-A90-460-010 HLDR,WIRE 2.5-7P

FAN C.B<LH>

C501 87-A12-087-080 CAP,E 1-50 SMG
C502 87-A12-090-080 CAP,E 47-25 SMG
C503 87-A12-071-080 CAP,E 47-25 SMG
CN502 87-A60-688-010 CONN,4P H GRY TUC-P04X-C1
CN503 87-A60-109-010 CONN,2P V S2M-2W

TOP C.B

C190 87-012-271-080 CAP, U 560P-50
C191 87-012-195-080 C-CAP,U 100P-50CH
CN122 87-A60-154-010 CONN,6P H FE
S301 87-A90-095-080 SW,TACT EVQ11G04M
S302 87-A90-095-080 SW,TACT EVQ11G04M

S303 87-A90-095-080 SW,TACT EVQ11G04M
S304 87-A90-095-080 SW,TACT EVQ11G04M
S305 87-A90-095-080 SW,TACT EVQ11G04M
SW163 87-A91-991-010 SW,RTRY REO12303PVB8H

MOT.B

CN402 87-A60-130-010 CONN,5P V FE
M401 87-045-305-010 MOTOR, RF-500TB DC-5V (2MA)
S401 87-036-110-010 SW,MICRO SPPB62
S402 87-036-110-010 SW,MICRO SPPB62

MIC C.B<LH>

C502 87-010-186-080 CAP,CHIP 4700P-50
C503 87-010-112-040 CAP,E 100-16
C505 87-010-491-040 CAP,E 0.22-50M 5L SRE
C506 87-010-320-080 CHIP CAP 68P
C507 87-010-545-040 CAP,E 0.22-50M 11L SME

C508 87-010-544-040 CAP,E 0.1-50 SME
C510 87-010-322-080 C-CAP,S 100P-50 CH
C511 87-A12-065-040 CAP,E 33-16 SMG
C512 87-010-178-080 CHIP CAP 1000P
C513 87-010-196-080 CHIP CAPACITOR,0.1-25

C514 87-010-196-080 CHIP CAPACITOR,0.1-25
C515 87-010-178-080 CHIP CAP 1000P
C520 87-010-177-080 C-CAP,S 820P-50 SL
CN551 87-A60-586-010 CONN,4P V FE
FB501 87-008-372-080 FILTER, EMI BL01 RN1

J501 87-A61-243-010 JACK,6.3 BLK MONO W/SW V MSC
VR501 87-NB7-602-010 VR,RTRY 10KAX1 1 V

KEY C.B

CN141 87-009-030-010 CONN,2P V WHT PH
S321 87-A90-095-080 SW,TACT EVQ11G04M
S322 87-A90-095-080 SW,TACT EVQ11G04M
S323 87-A90-095-080 SW,TACT EVQ11G04M
S324 87-A90-095-080 SW,TACT EVQ11G04M

S325 87-A90-095-080 SW,TACT EVQ11G04M
S326 87-A90-095-080 SW,TACT EVQ11G04M
S327 87-A90-095-080 SW,TACT EVQ11G04M<LH>

DECK C.B

CN1 87-A60-079-010 CONN,08P H 9604S-08F
M1 87-A91-825-010 MOT,M09Y/Z
S1 87-036-110-010 PUSH SWITCH
S2 87-036-110-010 PUSH SWITCH
S4 87-036-110-010 PUSH SWITCH

S5 87-036-110-010 PUSH SWITCH
SOL1 82-ZM3-628-010 SOL ASSY,23 SO

– 15 –