Page 1
XR-MS3
EZ, U
SERVICE MANUAL
COMPACT DISC
STEREO SYSTEM
SYSTEM
XR–MS3
• This Service Manual is the “Revision Publishing” and replaces “Simple Manual”
XR-MS3 (U,EZ), (S/M Code No. 09-001-422-6T1).
• This Service Manual does not include “CD ELECTRICAL SECTION”.
These items will be issued in the next Suplement.
BASIC TAPE MECHANISM : 2ZM-1 R10NM
BASIC CD MECHANISM : TN-CCD1001-902M
SPEAKER
SX-MS7
S/M Code No. 09-002-422-6R1
REVISION
DAT A
Page 2
TABLE OF CONTENTS
SPECIFICATIONS ................................................................................................................................................................3
PROTECTION OF EYES FROM LASER BEAM DURING SERVICING ....................................................................... 4
PRECAUTION TO REPLACE OPTICAL BLOCK .............................................................................................................4
SERVICE JIG AND TOOLS ............................................................................................................................................... 5
DISASSEMBLY INSTRUCTIONS................................................................................................................................. 6 ~ 9
ELECTRICAL MAIN PARTS LIST ........................................................................................................................... 10 ~ 13
TRANSISTOR ILLUSTRATION .........................................................................................................................................14
WIRING – 1 (U : MAIN / VM) ....................................................................................................................................... 15, 16
SCHEMATIC DIAGRAM – 1 (U : MAIN 1 / 2 / HP JACK) ................................................................................................ 17
SCHEMATIC DIAGRAM – 2 (U : MAIN 2 / 2) ..................................................................................................................18
WIRING – 2 (EZ : MAIN / VM) ..................................................................................................................................... 19, 20
SCHEMATIC DIAGRAM – 3 (EZ : MAIN 1 / 2 / HP JACK) .............................................................................................. 21
SCHEMATIC DIAGRAM – 4 (EZ : MAIN 2 / 2) ................................................................................................................22
WIRING – 3 (FRONT / HP JACK)......................................................................................................................................23
SCHEMATIC DIAGRAM – 5 (FRONT) ............................................................................................................................. 24
WIRING – 4 (TAPE) ..................................................................................................................................................... 25, 26
SCHEMATIC DIAGRAM – 6 (TAPE / DECK / RELAY)..................................................................................................... 27
SCHEMATIC DIAGRAM – 7 (VM) .................................................................................................................................... 28
WIRING – 5 (U : PT) ..........................................................................................................................................................29
WIRING – 6 (EZ : PT) ........................................................................................................................................................30
SCHEMATIC DIAGRAM – 8 (PT) .....................................................................................................................................31
WIRING – 7 (U : TUNER) .................................................................................................................................................. 32
SCHEMATIC DIAGRAM – 9 (U : TUNER)........................................................................................................................ 33
WIRING – 8 (EZ : TUNER) ................................................................................................................................................ 34
SCHEMATIC DIAGRAM – 10 (EZ : TUNER).................................................................................................................... 35
WIRING – 9 (DECK / RELAY)............................................................................................................................................ 36
IC BLOCK DIAGRAM................................................................................................................................................37 ~ 39
ADJUSTMENT (TUNER / DECK / MAIN) ..................................................................................................................40 ~ 43
IC DESCRIPTION ........................................................................................................................................................ 44, 45
CD TEST MODE ............................................................................................................................................................... 46
FL (9-ST-19GONK) GRID ASSIGNMENT / ANODE CONNECTION .....................................................................47 ~ 49
MECHANICAL EXPLODED VIEW 1 / 1........................................................................................................................... 50
MECHANICAL PARTS LIST 1 / 1 .................................................................................................................................... 51
TAPE MECHANISM EXPLODED VIEW 1 / 1 ................................................................................................................. 52
TAPE MECHANISM PARTS LIST 1 / 1 ..........................................................................................................................53
CD MECHANISM EXPLODED VIEW 1 / 1 .....................................................................................................................54
CD MECHANISM PARTS LIST 1 / 1 .............................................................................................................................. 55
SPEAKER DISASSEMBLY INSTRUCTIONS................................................................................................................... 56
SPEAKER PARTS LIST 1 / 1...........................................................................................................................................57
ACCESSORIES / PACKAGE LIST ....................................................................................................................................57
– 2 –
Page 3
SPECIFICATIONS
<FM tuner section>
Tuning range 87.5 MHz to 108 MHz
Usable sensitivity (IHF) U : 13.2 dBf
EZ : 16.8 dBf
Antenna terminals 75 ohms (unbalanced)
<AM (MW) tuner section>
Tuning range 530 kHz to 1710 kHz (10 kHz step)
531 kHz to 1602 kHz (9 kHz step)
Usable sensitivity 350 µV/m
Antenna Loop antenna
<LW tuner section> (EZ)
Tuning range 144 kHz to 290 kHz
Usable sensitivity 1400
µV/m
Antenna Loop antenna
<Amplifier section>
Power output U : 10 W + 10 W
(50 Hz to 20 kHz, T.H.D. less than
1 %, 6 ohms)
15 W + 15 W
(50 Hz to 20 kHz, T.H.D. less than
10 %, 6 ohms)
EZ : Rated : 12 W + 12 W (6 ohms,
T.H.D. 1 %, 1 kHz / DIN 45500)
Reference : 15 W + 15 W (6 ohms,
T.H.D. 10 %, 1 kHz / DIN 45324)
DIN MUSIC POWER
20 W + 20 W
Total harmonic distortion (U) 0.15 % (6W, 1 kHz, 6 ohms, DIN
AUDIO)
Input VIDEO / AUX: 500 mV
Outputs SPEAKERS: accept speakers of 6
ohms or more
PHONES (stereo mini jack): accepts
headphones of 16 ohms or more
DIGITAL OUT (OPTICAL) jack
<General>
Power requirements U : 120 V AC, 60 Hz
EZ : 230 V AC, 50 Hz
Power consumption U : 45 W
EZ : 57 W
Standby power consumption U : 1.9 W (power-economizing
mode set to ON)
EZ : 1.7 W (power-economizing
mode set to ON)
Dimensions of main unit 100 x 210.6 x 271.5 mm
(W x H x D) (4 x 8
3
/8 x 103/4 in.)
Weight of main unit 3.8 kg (8 lbs 6 oz.)
<Speaker system>
Cabinet type 2 way, bass reflex (magnetic
shielded type)
Speakers Woofer : 85 mm
Tweeter: 22 mm dome type
Impedance 6 ohms
Output sound pressure level 86 dB/W/m
Dimensions 100 x 206 x 188 mm
(W x H x D) (4 x 8
1
/8 x 71/2 in.)
Weight 1.5 kg (3 lbs 5 oz.)
<Compact disc player section>
Laser Semiconductor laser (λ = 780 nm)
D-A converter 1 bit dual
Signal-to-noise ratio 85 dB (1 kHz, 0 dB)
Harmonic distortion 0.05 % (1 kHz, 0 dB)
Wow and flutter Unmeasurable
<Cassette deck section>
Track format 4 tracks, 2 channels stereo
Frequency response CrO
Signal-to-noise ratio 60 dB (Dolby B NR ON, CrO
2 tape : 50 Hz – 16000 Hz
Normal
tape : 50 Hz – 15000 Hz
2 tape
peak level)
Recording system AC bias
Heads Recording / Playback head x 1,
erase head x 1
• Design and specifications are subject to change without notice.
• The word "BBE"and the "BBE symbol" are trademarks of BBE
Sound, Inc.
Under license from BBE Sound,Inc.
• Dolby noise reduction manufactured under license from Dolby
Laboratories Licensing Corporation.
"DOLBY" and the double-D symbol are trademarks of Dolby
Laboratories Licensing Corporation.
– 3 –
Page 4
PROTECTION OF EYES FROM LASER BEAM DURING SERVICING
This set employs laser. Therefore, be sure to follow carefully
the instructions below when servicing.
WARNING!!
WHEN SERVICING, DO NOT APPROACH THE LASER
EXIT WITH THE EYE TOO CLOSELY. IN CASE IT IS
NECESSARY TO CONFIRM LASER BEAM EMISSION.
BE SURE TO OBSERVE FROM A DISTANCE OF MORE
THAN 30cm FROM THE SURFACE OF THE OBJECTIVE LENS ON THE OPTICAL PICK-UP BLOCK.
s Caution: Invisible laser radiation when
open and interlocks defeated avoid
exposure to beam.
s Advarsel: Usynlig laserståling ved åbning,
når sikkerhedsafbrydere er ude af funktion.
Undgå udsættelse for stråling.
VAROITUS!
Laiteen Käyttäminen muulla kuin tässä käyttöohjeessa
mainitulla tavalla saataa altistaa käyt-täjän
turvallisuusluokan 1 ylittävälle näkymättömälle
lasersäteilylle.
VARNING!
Om apparaten används på annat sätt än vad som
specificeras i denna bruksanvising, kan användaren
utsättas för osynling laserstrålning, som överskrider
gränsen för laserklass 1.
CAUTION
Use of controls or adjustments or performance of procedures other than those specified herin may result in
hazardous radiation exposure.
ATTENTION
L’utillisation de commandes, réglages ou procédures
autres que ceux spécifiés peut entraîner une dangereuse
exposition aux radiations.
ADVARSEL
Usynlig laserståling ved åbning, når sikkerhedsafbrydereer
ude af funktion. Undgå udsættelse for stråling.
This Compact Disc player is classified as a CLASS 1
LASER product.
The CLASS 1 LASER PRODUCT label is located on the
rear exterior.
CLASS 1 LASER PRODUCT
KLASSE 1 LASER PRODUKT
LUOKAN 1 LASER LAITE
KLASS 1 LASER APPARAT
Precaution to replace Optical block
(VED0375-TN)
Body or clothes electrostatic potential could
ruin laser diode in the optical block. Be sure
ground body and workbench, and use care the
clothes do not touch the diode.
1) After the connection, remove solder shown in
right figure.
PICK-UP ASSY
VED0375-TN
SOLDER
– 4 –
Page 5
SERVICE JIG AND TOOLS
The distance between the FRONT C.B and the MAIN C.B may be extended with the jig when repairing the FRONT C.B.
Name: JIG, EXT 18P
No.: SV-J00-071-010
1. Assemble Method
1) Remove the solders on the pattern side of JIG C.B.
2) Remove the covers by pushing the picks of sockets (as shown by Fig. 1).
3) Insert and solder the parts into JIG C.B (as shown by Fig. 2).
4) Insert FFC cable into each connector to connect a socket part and a plug part (Fig. 2). Fig. 1
Fig. 2
2. Connection
As shown in the figure below, connect the plug side to the FRONT C.B and the socket side to the MAIN C.B.
• Beware of short circuit on the pattern side of the JIG C.B and FFC coming off.
Fig. 3
– 5 –
Page 6
DISASSEMBLY INSTRUCTIONS
1. CD BLOCK
1) Remove the PANEL, SIDE.
Remove the four screws indicated by the arrows
and remove the PANEL, SIDE (right and left).
Screw
Screw
Screw
2) Remove the CABI, TOP ASSY.
Remove the five screws indicated by the arrows
and remove the CABI, TOP ASSY.
Screw
PANEL, SIDE
Screw
Screw
CABI, TOP ASSY
Screw
Screw
3) Remove the CABI, REAR.
Remove the eight screws indicated by the arrows and
remove the CABI, REAR.
CABI, REAR
Screw Screw
Screw
– 6 –
Page 7
4) Remove the TUNER board.
Remove the TUNER board connected to the connector.
5) Remove the CABI, FR ASSY.
Remove the three screws indicated by the arrows and remove
the CABI, FR ASSY.
CABI, FR ASSY
TUNER board
Screw
Screw
6) Remove the CD MECHA.
(1) Remove the two screws indicated by the arrows.
(2) Lift up the CD MECHA in the direction of arrow 1 and
hook in the position indicated in circle.
(3) Remove the CD MECHA in the direction of arrow 2.
Screw
2
Screw Screw
1
Hook
– 7 –
Page 8
7) Lay the XR-MS3 in its Service Position.
(1) Attach the CABI, FR ASSY.
(2) Place the main unit and the CD unit as shown below.
(3) Connect the CABLE, FFC 15P and CONN, ASSY 2P to
the CD MECHA and turn on the main power.
Service Position
CABLE, FFC 15P
CONN, ASSY 2P
– 8 –
Page 9
2. CASSETTE BLOCK
1) Remove the CABI, TOP ASSY in the same procedure (1 ~ 3)
as for CD block.
CABI, TOP ASSY
2) Remove the HLDR, FR and HLDR, REAR.
Remove the six screws indicated by the arrows and remove
the HLDR, FR and HLDR, REAR.
3) Remove the HLDR, FR and HLDR, REAR.
Remove the six screws indicated by the arrows and remove
the HLDR, FR and HLDR, REAR.
Screw Screw
HLDR, FR
Screw Screw
HLDR, REAR
Screw Screw
Service Position
CABLE, FFC 14P
CABLE, FFC 9P
– 9 –
Page 10
ELECTRICAL MAIN PARTS LIST
PART NO.
NO.
IC
8A-CJ5-601-010 C-IC,LC876580W-5N98
87-070-246-010 IC,GP1U271X
87-A20-909-010 IC,LA4663
87-017-915-080 IC,BU4094BCF
87-017-585-080 IC,NJM4580E
87-A20-355-010 IC,CXA1553P
87-A20-783-040 C-IC,BA7762AFS
87-A21-022-040 C-IC,BA3880FS
87-A21-103-040 C-IC,MM1454XFBE
87-A21-111-040 C-IC,M62495FP
87-017-825-010 IC,GP1F32T
87-020-454-010 IC,DN6851
87-070-127-110 IC,LC72131D
87-A20-913-010 IC,LA1837NL
87-A20-440-040 C-IC,BU1920FS<EZ>
TRANSISTOR
89-213-702-010 TR,2SB1370E
87-A30-076-080 C-TR,2SC3052F
87-026-610-080 TR,KTC3198GR
87-A30-075-080 C-TR,2SA1235F
87-A30-234-080 TR,CSC4115BC
89-418-580-080 TR,2SD1858TV2
87-026-245-080 TR,DTC114ES
87-A30-198-080 TR,KTC3199GR
87-026-609-080 TR,KTA1266GR
87-026-210-080 CHIP-TR,DTC144EK
87-A30-087-080 C-FET,2SK2158
87-A30-073-080 C-TR,RT1N 141C
87-026-236-080 C-TR,DTC124EK
87-A30-086-070 C-TR,CSD1306E
87-026-211-080 C-TR,DTA144EK
87-A30-240-080 TR,CSA1585BC
87-A30-159-080 C-TR,KTA1298Y
87-A30-072-080 C-TR,RT1P 144C
87-A30-273-040 C-TR,DTC124EKA
87-A30-202-080 C-TR,RT1P441C
89-505-434-540 C-FET,2SK543(4/5)
87-A30-074-080 C-TR,RT1P 141C
89-327-143-080 C-TR,2SC2714(0.1W)
DIODE
87-020-465-080 DIODE,1SS133
87-A40-224-010 DIODE,GBU8DL
87-A40-313-080 C-DIODE,MC 2840
87-A40-346-080 ZENER,MTZJ 8.2C
87-A40-345-080 ZENER,MTZJ10C
87-070-274-080 DIODE,1N4003 SEM
87-A40-336-080 ZENER,MTZJ27D T-72
87-A40-435-080 ZENER,MTZJ30D
87-A40-270-080 C-DIODE,MC2838
87-A40-004-080 ZENER,MTZJ16A
87-070-136-080 ZENER,MTZJ5.1B
87-A40-509-080 ZENER,MTZJ6.8C
87-A40-269-080 C-DIODE,MC2836
87-A40-235-080 ZENER,MTZJ9.1C
87-A40-293-080 ZENER,DZ2.7M
87-A40-438-080 ZENER,MTZJ4.7A
87-017-149-080 ZENER,HZS6A2L
MAIN C.B
C1 87-010-194-080 CAP, CHIP 0.047
C2 87-010-194-080 CAP, CHIP 0.047
C3 87-010-196-080 CHIP CAPACITOR,0.1-25
C4 87-010-196-080 CHIP CAPACITOR,0.1-25
C5 87-010-196-080 CHIP CAPACITOR,0.1-25
DESCRIPTIONREF. NO. KANRI
REF. NO. DESCRIPTIONPART NO.
C6 87-010-196-080 CHIP CAPACITOR,0.1-25
C7 87-010-194-080 CAP, CHIP 0.047
C8 87-010-196-080 CHIP CAPACITOR,0.1-25
C9 87-A12-033-090 CAP,E 6800-25 SMG30L
C10 87-010-409-080 CAP,E 220-50 SME
C11 87-010-380-080 CAP, ELECT 47-16V
C13 87-010-408-080 CAP, ELECT 47-50V
C14 87-010-235-080 CAP,E 470-16 SME
C15 87-010-387-080 CAP,E 470-25 SME
C16 87-012-369-080 C-CAP,S 0.047-50F
C17 87-012-369-080 C-CAP,S 0.047-50F
C18 87-A10-776-080 CAP,E 1000-25 M 105 KMG
C19 87-010-403-080 CAP, ELECT 3.3-50V
C30 87-010-112-080 CAP, ELECT 100-16V
C31 87-016-126-080 CAP,E 470-16 M 105 KME
C61 87-010-260-080 CAP, ELECT 47-25V
C62 87-010-496-040 CAP,E 3.3-50 GAS
C91 87-010-401-080 CAP, ELECT 1-50V
C92 87-010-263-080 CAP, ELECT 100-10V
C93 87-010-553-040 CAP,E 47-16 GAS
C101 87-010-754-080 CAP,E220-10 SRA 7L
C102 87-010-754-080 CAP,E220-10 SRA 7L
C103 87-010-196-080 CHIP CAPACITOR,0.1-25
C104 87-010-198-080 CAP, CHIP 0.022
C105 87-010-196-080 CHIP CAPACITOR,0.1-25
C106 87-010-400-040 CAP,E 0.47-50
C108 87-010-313-080 CAP, CHIP 18P
C109 87-012-156-080 C-CAP,S 220P-50 CH
C110 87-010-196-080 CHIP CAPACITOR,0.1-25
C111 87-010-079-040 CAP,E 100-6.3 5L
C112 87-010-194-080 CAP, CHIP 0.047
C114 87-010-194-080 CAP, CHIP 0.047
C115 87-010-405-040 CAP,E 10-50
C116 87-010-196-080 CHIP CAPACITOR,0.1-25
C117 87-010-196-080 CHIP CAPACITOR,0.1-25
C118 87-010-196-080 CHIP CAPACITOR,0.1-25
C129 87-010-316-080 C-CAP,S 33P-50 CH
C130 87-010-178-080 CHIP CAP 1000P
C201 87-010-491-040 CAP,E 0.22-50 GAS
C202 87-010-545-040 CAP,E 0.22-50 SME
C203 87-010-178-080 CHIP CAP 1000P
C204 87-010-178-080 CHIP CAP 1000P
C205 87-010-546-040 CAP,E 0.33-50
C206 87-010-546-040 CAP,E 0.33-50
C211 87-010-405-040 CAP,E 10-50
C212 87-010-260-080 CAP, ELECT 47-25V
C215 87-010-405-080 CAP, ELECT 10-50V
C216 87-010-405-080 CAP, ELECT 10-50V
C217 87-012-368-080 C-CAP,S 0.1-50 F
C218 87-012-368-080 C-CAP,S 0.1-50 F
C219 87-012-368-080 C-CAP,S 0.1-50 F
C220 87-012-368-080 C-CAP,S 0.1-50 F
C221 87-010-405-080 CAP, ELECT 10-50V
C223 87-010-196-080 C-CAP,S 0.1-25 ZF
C301 87-010-322-080 C-CAP,S 100P-50 CH
C302 87-010-322-080 C-CAP,S 100P-50 CH
C303 87-016-044-040 CAP,E 100-16 GAS
C304 87-016-044-040 CAP,E 100-16 GAS
C305 87-010-071-040 CAP,E 1-50 M 5L SRE
C306 87-010-071-040 CAP,E 1-50 M 5L SRE
C307 87-010-553-040 CAP,E 47-16 GAS
C308 87-010-555-040 CAP,E 100-10 GAS
C401 87-010-196-080 CHIP CAPACITOR,0.1-25
C402 87-010-260-080 CAP, ELECT 47-25V
C403 87-010-404-080 CAP, ELECT 4.7-50V
C404 87-010-404-080 CAP, ELECT 4.7-50V
C405 87-010-404-080 CAP, ELECT 4.7-50V
C406 87-010-404-080 CAP, ELECT 4.7-50V
C407 87-010-188-080 CAP,CHIP 6800P
C408 87-010-188-080 CAP,CHIP 6800P
KANRI
NO.
– 10 –
Page 11
PART NO. KANRI
DESCRIPTIONREF. NO. KANRI
NO.
C409 87-012-140-080 CAP 470P
C410 87-012-140-080 CAP 470P
C411 87-010-404-080 CAP, ELECT 4.7-50V
C412 87-010-404-080 CAP, ELECT 4.7-50V
C413 87-010-404-080 CAP, ELECT 4.7-50V
C414 87-010-404-080 CAP, ELECT 4.7-50V
C415 87-010-197-080 CAP, CHIP 0.01 DM
C416 87-010-197-080 CAP, CHIP 0.01 DM
C417 87-010-195-080 C-CAP,S 0.068-25 F
C418 87-010-195-080 C-CAP,S 0.068-25 F
C419 87-010-260-080 CAP, ELECT 47-25V
C421 87-012-140-080 CAP 470P
C422 87-012-140-080 CAP 470P
C552 87-010-405-080 CAP, ELECT 10-50V
C553 87-010-260-080 CAP, ELECT 47-25V
C554 87-010-197-080 CAP, CHIP 0.01 DM
C555 87-010-197-080 CAP, CHIP 0.01 DM
C557 87-010-405-080 CAP, ELECT 10-50V
C573 87-010-405-080 CAP, ELECT 10-50V
C574 87-010-405-080 CAP, ELECT 10-50V
C575 87-010-322-080 C-CAP,S 100P-50 CH
C601 87-010-187-080 CAP CHIP S5600P
C602 87-010-187-080 CAP CHIP S5600P
C605 87-010-182-080 C-CAP,S 2200P-50 B
C606 87-010-182-080 C-CAP,S 2200P-50 B
C607 87-010-213-080 C-CAP,S 0.015-50 B
C608 87-010-213-080 C-CAP,S 0.015-50 B
C609 87-010-545-080 CAP, ELECT 0.22-50V
C610 87-010-491-080 CAP,E 0.22-50 GAS
C611 87-010-545-080 CAP, ELECT 0.22-50V
C612 87-010-491-080 CAP,E 0.22-50 GAS
C613 87-010-553-080 CAP,E 47-16
C614 87-010-553-080 CAP,E 47-16
C615 87-010-154-080 CAP CHIP 10P
C622 87-010-402-080 CAP, ELECT 2.2-50V
C623 87-010-402-080 CAP, ELECT 2.2-50V
C641 87-010-196-080 CHIP CAPACITOR,0.1-25
C643 87-010-805-080 CAP, S 1-16
C644 87-010-196-080 CHIP CAPACITOR,0.1-25
C702 87-018-209-080 CAP,TU U 0.1-50 ZF
C703 87-010-197-080 CAP, CHIP 0.01 DM
C704 87-010-382-040 CAP,E 22-25 SME
C706 87-010-382-040 CAP,E 22-25 SME
C902 87-010-322-080 C-CAP,S 100P-50 CH
C903 87-010-322-080 C-CAP,S 100P-50 CH
CN1 87-A60-850-010 CONN,7P V VH
CN91 87-A60-619-010 CONN,2P V 2MM JMT
CN601 87-A60-902-010 CONN,14P V BLK FMN-BTRK
CN701 87-A60-619-010 CONN,2P V 2MM JMT
CN901 87-A60-770-010 CONN,18P B TMC-D(X)
CN902 87-A60-900-010 CONN,9P V BLK FMN-BTRK
CN903 87-A60-189-010 CONN,16P V TUC-P16P-B1<EZ>
CN904 87-099-570-010 CONN,13P TUC-P13P-B1<U>
CN905 87-A61-258-010 CONN,15P V 52806-1510
CNA002 88-805-040-820 CONN ASSY,4P 80
CNA003 88-805-051-420 CONN ASSY,5P 140
CNA201 88-805-043-020 CONN ASSY,4P 300
CNA700 8A-CJ5-634-010 CONN ASSY,2P SHLD
!
F1 87-A90-172-080 FUSE,1A 125V 251<U>
!
F2 87-A90-410-080 FUSE,0.5A 125V 251<U>
F3 87-A90-210-080 FUSE,7A 125V 251<U>
!
!
F4 87-A90-210-080 FUSE,7A 125V 251<U>
F5 87-A90-172-080 FUSE,1A 125V 251<U>
!
FC905 8A-CL5-626-010 CABLE,FFC15P-1.0 130
J201 87-A60-238-010 TERMINAL,SP 4P (MSC)
J202 87-099-801-010 JACK,PIN 1P BLK
J601 87-A60-881-010 JACK,PIN 2P MSP 242V05 PBSN
L101 87-A50-333-010 COIL,OSC 9.43MHZ
!
PR1 87-026-689-080 PROTECTOR,1A 60V 491<EZ>
!
PR2 87-026-689-080 PROTECTOR,1A 60V 491<EZ>
REF. NO. DESCRIPTIONPART NO.
NO.
!
PR3 87-A90-195-080 PROTECTOR 7A 125V 49<EZ>
PR4 87-A90-195-080 PROTECTOR 7A 125V 49<EZ>
!
PR5 87-026-689-080 PROTECTOR,1A 60V 491<EZ>
!
WH005 87-A90-507-010 HLDR,WIRE 2.5-4P
FRONT C.B
C102 87-010-415-040 CAP,E 10-50 5L
C103 87-012-157-080 C-CAP,S 330P-50 CH
C104 87-010-421-040 CAP,E 4.7-50 5L
C105 87-010-421-040 CAP,E 4.7-50 5L
C106 87-010-408-040 CAP,E 47-50 SME
C107 87-012-369-080 C-CAP,S 0.047-50F
C108 87-010-197-080 CAP, CHIP 0.01 DM
C109 87-010-197-080 CAP, CHIP 0.01 DM
C110 87-010-196-080 CHIP CAPACITOR,0.1-25
C111 87-012-368-080 C-CAP,S 0.1-50 F
C301 87-010-196-080 CHIP CAPACITOR,0.1-25
CN101 87-A60-778-010 CONN,18P B TMC-D(P)
FL101 8A-CL5-608-010 FL,9-ST-19GONK
LED101 87-A40-317-080 LED,SLR-342VCT31 RED
LED301 87-A40-786-080 LED,SMLS1BE16WTP4 BLU/UMB
LED302 87-A40-786-080 LED,SMLS1BE16WTP4 BLU/UMB
LED303 87-A40-786-080 LED,SMLS1BE16WTP4 BLU/UMB
R102 87-022-355-080 C-RES,S10K-1/10W F
R103 87-022-355-080 C-RES,S10K-1/10W F
S102 87-A91-426-010 SW,RTRY 3-2-1 RE01311-2-12PCE
S201 87-A90-095-080 SW,TACT EVQ11G04M
S202 87-A90-095-080 SW,TACT EVQ11G04M
S203 87-A90-095-080 SW,TACT EVQ11G04M
S204 87-A90-095-080 SW,TACT EVQ11G04M
S205 87-A90-095-080 SW,TACT EVQ11G04M
S206 87-A90-095-080 SW,TACT EVQ11G04M
S207 87-A90-095-080 SW,TACT EVQ11G04M
S208 87-A90-095-080 SW,TACT EVQ11G04M
S209 87-A90-095-080 SW,TACT EVQ11G04M
S210 87-A90-095-080 SW,TACT EVQ11G04M
S211 87-A90-095-080 SW,TACT EVQ11G04M
S212 87-A90-095-080 SW,TACT EVQ11G04M
S213 87-A90-095-080 SW,TACT EVQ11G04M
S214 87-A90-095-080 SW,TACT EVQ11G04M
S215 87-A90-095-080 SW,TACT EVQ11G04M
S216 87-A90-095-080 SW,TACT EVQ11G04M
TAPE C.B
C303 87-012-157-080 C-CAP,S 330P-50 CH
C304 87-012-157-080 C-CAP,S 330P-50 CH
C307 87-010-196-080 CHIP CAPACITOR,0.1-25
C311 87-010-198-080 CAP, CHIP 0.022
C312 87-010-198-080 CAP, CHIP 0.022
C315 87-012-274-080 CHIP CAP,U 1000P-50B
C316 87-012-274-080 CHIP CAP,U 1000P-50B
C317 87-A10-201-080 C-CAP,S0.33-16 KB
C318 87-A10-201-080 C-CAP,S0.33-16 KB
C319 87-012-141-080 CHIP-CAPACITOR,0.22-16F
C320 87-012-141-080 CHIP-CAPACITOR,0.22-16F
C321 87-A10-025-080 C-CAP,U 0.22-16Z F
C322 87-A10-025-080 C-CAP,U 0.22-16Z F
C324 87-010-260-040 CAP,E 47-25 SME
C325 87-010-370-040 CAP,E 330-6.3 SME
C327 87-010-404-040 CAP,E 4.7-50 SME
C328 87-010-404-040 CAP,E 4.7-50 SME
C332 87-010-196-080 CHIP CAPACITOR,0.1-25
C335 87-010-401-040 CAP,E 1-50 SME
C336 87-010-401-040 CAP,E 1-50 SME
C337 87-010-196-080 CHIP CAPACITOR,0.1-25
C339 87-010-831-080 C-CAP,U,0.1-16F
C340 87-010-196-080 CHIP CAPACITOR,0.1-25
C351 87-012-140-080 CAP 470P
– 11 –
Page 12
PART NO. KANRI
DESCRIPTIONREF. NO. KANRI
NO.
C352 87-012-140-080 CAP 470P
C354 87-010-175-080 CAP 560P
C355 87-010-178-080 CHIP CAP 1000P
C356 87-010-260-040 CAP,E 47-25 SME
C357 87-010-197-080 CAP, CHIP 0.01 DM
C358 87-010-183-080 C-CAP,S 2700P-50 B
C359 87-010-183-080 C-CAP,S 2700P-50 B
C360 87-010-183-080 C-CAP,S 2700P-50 B
C370 87-010-196-080 CHIP CAPACITOR,0.1-25
C371 87-010-177-080 C-CAP,S 820P-50 SL
C372 87-010-177-080 C-CAP,S 820P-50 SL
C373 87-010-179-080 CAP,CHIP S B1200P
C374 87-010-179-080 CAP,CHIP S B1200P
C375 87-010-545-040 CAP,E 0.22-50 SME
C376 87-010-545-040 CAP,E 0.22-50 SME
C378 87-010-196-080 CHIP CAPACITOR,0.1-25
C386 87-010-759-080 C-CAP,U, 0.1-25F
C388 87-012-266-080 C-CAP,U 220P-50 B
CN251 87-A60-626-010 CONN,9P V 2MM JMT
CN351 87-A60-625-010 CONN,8P V 2MM JMT
CN601 87-A60-891-080 C-CONN,14P V FMN-BMTTN-TF
CN902 87-A60-888-080 C-CONN,9P V FMN-BMTTN-TF
FC601 8A-CL5-628-010 CABLE,FFC14P-1.0 160
FC902 8A-CL5-627-010 CABLE,FFC9P-1.0 220
L301 87-A50-049-010 COIL,TRAP 85K(COI)
L302 87-A50-049-010 COIL,TRAP 85K(COI)
L351 87-007-342-010 COIL,OSC 85K BIAS
SFR303 87-024-435-080 SFR 33K RH 063EC
SFR304 87-024-435-080 SFR 33K RH 063EC
SFR305 87-A90-433-080 SFR,50K H NVZ6TLTA
SFR306 87-A90-433-080 SFR,50K H NVZ6TLTA
SFR351 87-A90-433-080 SFR,50K H NVZ6TLTA
SFR352 87-A90-433-080 SFR,50K H NVZ6TLTA
VM C.B
C27 87-012-140-080 CAP 470P
C28 87-010-263-080 CAP, ELECT 100-10V<U>
C29 87-010-247-080 CAP, ELECT 100-50V
CN3 87-009-033-010 CONNECTOR, 5P
R20 87-A00-261-080 RES,M/F 0.56-1W J<U>
HP-JACK C.B
CN102 87-A60-668-010 CONN,4P H 2MM JMT
J101 87-A60-420-010 JACK,3.5 ST (MSC)
PT C.B
!
C1 87-A10-479-080 CAP,CER 2200P-250 M E KH
!
CN1 87-A60-645-010 CONN,3P V VH
CN2 87-A60-621-010 CONN,4P V 2MM JMT
F1 87-A91-276-080 FUSE,125MA 125V F 251<U>
!
PT1 8Z-NF8-662-010 PT,SUB ZNF-8(E)<EZ>
!
!
PT1 8Z-NF8-661-010 PT,SUB ZNF-8(U)<U>
PT2 8A-CJ5-622-010 PT,ACJ-5 EZ<EZ>
!
PT2 8A-CJ5-621-010 PT,ACJ-5 U<U>
!
RY1 87-A90-977-010 RELAY,AC12V DG12D1-O(M)
!
T1 87-A60-317-010 TERMINAL, 1P MSC
!
T2 87-A60-317-010 TERMINAL, 1P MSC
!
TUNER C.B
C701 87-010-381-080 CAP,ELECT 330-16V
C702 87-010-404-080 CAP,ELECT 4.7-50V
C703 87-012-286-080 CAP,U 0.01-25
C704 87-012-286-080 CAP,U 0.01-25
C705 87-A10-592-080 C-CAP,S 0.015-50 J B<U>
C706 87-A10-592-080 C-CAP,S 0.015-50 J B<U>
C709 87-012-195-080 C-CAP,U 100P-50CH
REF. NO. DESCRIPTIONPART NO.
NO.
C711 87-010-260-080 CAP,ELECT 47-25V
C712 87-010-831-080 C-CAP,U,0.1-16F
C713 87-012-286-080 CAP,U 0.01-25<EZ>
C714 87-012-286-080 CAP,U 0.01-25
C715 87-012-195-080 C-CAP,U 100P-50CH<EZ>
C717 87-012-286-080 CAP,U 0.01-25
C719 87-012-286-080 CAP,U 0.01-25
C720 87-012-195-080 C-CAP,U 100P-50CH
C721 87-012-176-080 CAP,15P
C722 87-012-176-080 CAP,15P
C723 87-012-274-080 CHIP CAP,U 1000P-50B
C725 87-012-274-080 CHIP CAP,U 1000P-50B<U>
C725 87-018-131-080 CAP,TC U 1000P-50 KB<EZ>
C727 87-010-196-080 CHIP CAPACITOR,0.1-25
C728 87-010-248-080 CAP,ELECT 220-10V
C729 87-012-274-080 CHIP CAP,U 1000P-50B
C731 87-012-286-080 CAP,U 0.01-25
C733 87-010-987-080 C-CAP,S 1500P-50 CH<U>
C733 87-012-280-080 C-CAP,U 3300P-50 KB<EZ>
C734 87-010-987-080 C-CAP,S 1500P-50 CH<U>
C734 87-012-280-080 C-CAP,U 3300P-50 KB<EZ>
C735 87-010-987-080 C-CAP,S 1500P-50 CH<U>
C736 87-010-987-080 C-CAP,S 1500P-50 CH<U>
C737 87-A10-592-080 C-CAP,S 0.015-50 J B<U>
C738 87-A10-592-080 C-CAP,S 0.015-50 J B<U>
C751 87-012-365-080 C-CAP,S 0.027-25VBK<U>
C752 87-012-365-080 C-CAP,S 0.027-25VBK<U>
C752 87-012-282-080 C-CAP,U 4700P-50 KB<EZ>
C753 87-012-195-080 C-CAP,U 100P-50 J CH<EZ>
C755 87-012-286-080 CAP,U 0.01-25<EZ>
C756 87-012-286-080 CAP,U 0.01-25
C757 87-012-188-080 C-CAP,U 47P-50 CH
C758 87-012-167-080 C-CAP,U 5P-50 CH
C761 87-010-196-080 C-CAP,S 0.1-25 ZF<EZ>
C762 87-012-286-080 CAP,U 0.01-25<EZ>
C763 87-010-829-080 CAP,U 0.047-16
C764 87-012-337-080 C-CAP,U 56P-50 CH<U>
C765 87-012-286-080 CAP,U 0.01-25
C766 87-010-197-080 C-CAP,S 0.01-25 KB<EZ>
C768 87-012-286-080 CAP,U 0.01-25
C769 87-010-260-080 CAP,ELECT 47-25V
C770 87-010-829-080 CAP,U 0.047-16
C771 87-010-383-080 CAP,ELECT 33-25V
C772 87-010-829-080 CAP,U 0.047-16
C773 87-010-196-080 CHIP CAPACITOR,0.1-25
C774 87-010-263-080 CAP,ELECT 100-10V
C775 87-010-404-080 CAP,ELECT 4.7-50V
C776 87-012-286-080 CAP,U 0.01-25
C777 87-010-400-080 CAP, ELECT 0.47-50V<U>
C777 87-010-493-080 CAP,E 0.47-50 M 5L SRE<EZ>
C778 87-010-401-080 CAP,ELECT 1-50V
C779 87-010-401-080 CAP,ELECT 1-50V
C780 87-010-196-080 CHIP CAPACITOR,0.1-25
C781 87-010-405-080 CAP,ELECT 10-50V
C782 87-010-405-080 CAP,ELECT 10-50V
C783 87-012-286-080 CAP,U 0.01-25
C784 87-012-286-080 CAP,U 0.01-25
C785 87-010-401-080 CAP, ELECT 1-50V<U>
C785 87-010-402-080 CAP,ELECT 2.2-50V<EZ>
C786 87-010-401-080 CAP, ELECT 1-50V<U>
C786 87-010-402-080 CAP,ELECT 2.2-50V<EZ>
C787 87-012-275-080 C-CAP,U 1200P-50 B<EZ>
C788 87-012-275-080 C-CAP,U 1200P-50 B<EZ>
C789 87-012-275-080 C-CAP,U 1200P-50 B
C790 87-012-275-080 C-CAP,U 1200P-50 B
C791 87-010-405-080 CAP,ELECT 10-50V
C793 87-012-273-080 C-CAP,U 820P-50 B
C794 87-010-406-080 CAP,ELECT 22-50
C795 87-010-596-080 CAP,S 0.047-16
C796 87-010-403-080 CAP,ELECT 3.3-50V
– 12 –
Page 13
PART NO. KANRI
NO.
C797 87-012-276-080 C-CAP,U 1500P-50 KB<EZ>
C798 87-012-276-080 C-CAP,U 1500P-50 KB<EZ>
C799 87-010-829-080 CAP,U 0.047-16
C812 87-012-286-080 CAP,U 0.01-25
C814 87-012-286-080 CAP,U 0.01-25<EZ>
C820 87-010-260-080 CAP,ELECT 47-25V
C821 87-012-286-080 CAP,U 0.01-25
C822 87-012-286-080 CAP,U 0.01-25
C823 87-012-286-080 CAP,U 0.01-25
C828 87-010-196-080 CHIP CAPACITOR,0.1-25
C829 87-010-196-080 CHIP CAPACITOR,0.1-25
C859 87-012-286-080 C-CAP,U 0.01-25 KB<EZ>
C861 87-012-199-080 C-CAP,U 220P-50 J CH<EZ>
C862 87-012-199-080 C-CAP,U 220P-50 J CH<EZ>
C863 87-012-270-080 C-CAP,U 470P-50 KB<EZ>
C864 87-010-405-080 CAP,E 10-50 M 11L SME<EZ>
C865 87-010-196-080 C-CAP,S 0.1-25 ZF<EZ>
C866 87-010-405-080 CAP,E 10-50 M 11L SME<EZ>
C867 87-012-286-080 C-CAP,U 0.01-25 KB<EZ>
C868 87-012-184-080 C-CAP,U 33P-50 J CH<EZ>
C869 87-012-180-080 C-CAP,U 22P-50 J CH<EZ>
C940 87-012-286-080 C-CAP,U 0.01-25 KB<EZ>
C942 87-012-168-080 C-CAP,U 6P-50 D CH<EZ>
C947 87-012-286-080 C-CAP,U 0.01-25 KB<EZ>
C949 87-A10-039-080 C-CAP,U 470P-50 J CH<EZ>
C952 87-012-286-080 C-CAP,U 0.01-25 KB<EZ>
C958 87-010-197-080 C-CAP,S 0.01-25 KB<EZ>
C959 87-010-196-080 CHIP CAPACITOR,0.1-25<U>
C959 87-010-831-080 C-CAP,U 0.1-16 ZF<EZ>
C960 87-010-196-080 CHIP CAPACITOR,0.1-25
C961 87-012-170-080 C-CAP,U 8P-50 CH<U>
C962 87-010-401-080 CAP,E 1-50 M 11L SME<EZ>
C963 87-010-196-080 CHIP CAPACITOR,0.1-25<U>
CF801 87-008-261-010 FILTER, SFE10.7MA5-A<U>
CF801 87-008-423-010 FLTR,CF SFE10.7MS3G-A<EZ>
CF802 87-008-261-010 FILTER, SFE10.7MA5-A<U>
CF802 82-785-747-010 CF,MS2 GHY R<EZ>
CN701 87-A60-700-010 CONN,13P H GRY TUC-P13X-C1<U>
CN701 87-A60-650-010 CONN,16P H GRY TUC-P16X-C1<EZ>
FFE801 A8-8ZA-190-030 8ZA-1 FEUNM<U>
DESCRIPTIONREF. NO. KANRI
REF. NO. DESCRIPTIONPART NO.
NO.
FFE801 A8-6ZA-191-130 6ZA-1 FEENM<EZ>
J801 87-A60-702-010 TERMINAL,ANT 4P CJ-9036<U>
J801 87-033-241-010 TERMINAL,ANT 2P AJ-2039<EZ>
L771 87-A50-266-010 COIL,FM DET-2N(TOK)
L772 87-A90-110-010 FLTR,PCFJZH-450 (TOK)<U>
L772 87-A91-110-010 FLTR,PCFJZH-450(TOK)<EZ>
L781 87-005-847-010 COIL,2.2UH K CECS<EZ>
L791 87-A50-027-010 COIL,1 POLE MPX(TOK)<EZ>
L792 87-A50-027-010 COIL,1 POLE MPX(TOK)<EZ>
L832 87-005-847-080 COIL,2.2UH K CECS<EZ>
L851 87-005-847-080 COIL,2.2UH K CECS<EZ>
L941 87-A50-020-010 COIL,ANT LW(COI)252KHZ<EZ>
L942 87-A50-019-010 COIL,OSC LW(COI) 856KHZ<EZ>
L981 8Z-ZA1-667-010 COIL,AM PACK 4F(TOK)<U>
L981 8Z-ZA1-665-010 COIL,AM PACK 2(TOK)<EZ>
TC942 87-011-164-010 TRIMMER,CER 30P 4.5X3.9 VCT31<EZ>
X721 87-A70-061-010 VIB,XTAL 4.500MHZ CSA-309
X851 87-A70-091-010 VIB,XTAL 4.332MHZ CSA-309<EZ>
DECK C.B
CNA1 82-ZM1-636-010 CONN ASSY,9P
SFR1 87-024-581-010 SFR,3.3K H KVSF637A
SOL2 82-ZM1-634-010 SOL ASSY,23K
SW2 87-036-110-010 SW,MICRO SPPB62
SW3 87-036-110-010 SW,MICRO SPPB62
SW4 87-036-110-010 SW,MICRO SPPB62
SW5 87-036-110-010 SW,MICRO SPPB62
SW6 87-A90-248-010 SW,MICRO ESE11SH2CXQ
W1 82-ZM1-625-010 RBN-CORD,4P-5S
RELAY C.B
CN301 8A-CL5-625-010 CONN ASSY,8P RPB
CHIP RESISTOR PART CODE
Chip Resistor Part Coding
88
A
Resistor Code
Chip resistor
Wattage Type Tolerance
1/16W 1005 5% CJ
1/16W
1/10W
1/8W
1608
2125
3216
5%
5%
5%
Symbol
CJ
CJ
CJ
Figure
Value of resistor
Form
L
– 13 –
Dimensions (mm)
t
W
0.55
Resistor Code
108
118
128
LW t
1.0 0.5 0.35 104
1.6 0.8 0.45
2 1.25 0.45
3.2
1.6
: A
: A
Page 14
TRANSISTOR ILLUSTRATION
E C B
CSA1585
CSC4115
KTA1266
KTC3198
KTC3199
B
2SA1235
2SC2714
2SC3052
CSD1306
DTA144EK
DTC124EK
DTC124EKA
C
E
DTC144EK
KTA1298
RT1N141C
RT1P141C
RT1P144C
RT1P441C
B C E
2SB1370 2SD1858
D
G
S
2SK2158
E C B E C B
DTC114ES
S
G
D
2SK543
– 14 –
Page 15
WIRING - 1 (U: MAIN/VM) <1/2>
181920212223242526272829303132
17 16151413121110987654321
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
-15-
Q
R
S
T
U
Page 16
WIRING - 1 (U: MAIN/VM) <2/2>
A
B
C
D
E
F
G
151413121110987654321
<U ONLY>
16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32
H
I
J
<U ONLY>
K
L
M
N
O
P
Q
R
S
T
U
-16-
Page 17
SCHEMA TIC DIAGRAM - 1 (U : MAIN 1 / 2 / HP JACK)
HP
– 17 –
Page 18
SCHEMA TIC DIAGRAM - 2 (U : MAIN 2 / 2)
– 18 –
Page 19
WIRING - 2 (EZ: MAIN/VM) <1/2>
181920212223242526272829303132
17 16151413121110987654321
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
-19-
Q
R
S
T
U
Page 20
WIRING - 2 (EZ: MAIN/VM) <2/2>
A
B
C
D
151413121110987654321
16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32
E
<EZ ONLY>
F
G
H
I
J
K
L
M
<EZ ONLY>
N
O
P
Q
R
S
T
U
-20-
Page 21
SCHEMATIC DIAGRAM - 3 (EZ : MAIN 1 / 2 / HP JACK)
HP
– 21 –
Page 22
SCHEMATIC DIAGRAM - 4 (EZ : MAIN 2 / 2)
– 22 –
Page 23
WIRING - 3 (FRONT/HP JACK)
123456789101112131415
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
-23-
Q
R
S
T
U
Page 24
SCHEMATIC DIAGRAM - 5 (FRONT)
– 24 –
Page 25
WIRING - 4 (TAPE) <1/2>
123456789101112131415
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
-25-
Q
R
S
T
U
Page 26
WIRING - 4 (TAPE) <2/2>
A
B
C
D
E
F
G
151413121110987654321
H
I
J
K
L
M
N
O
P
Q
R
S
T
U
-26-
Page 27
SCHEMATIC DIAGRAM - 6 (TAPE / DECK / RELAY)
– 27 –
Page 28
SCHEMATIC DIAGRAM - 7 (VM)
– 28 –
Page 29
WIRING - 5 (U: PT)
123456789101112131415
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
-29-
Q
R
S
T
U
Page 30
WIRING - 6 (EZ: PT)
123456789101112131415
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
-30-
Q
R
S
T
U
Page 31
SCHEMATIC DIAGRAM - 8 (PT)
– 31 –
Page 32
WIRING - 7 (U: TUNER)
101112131415161718192021222324
1234567892526272829303132
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
-32-
Q
R
S
T
U
Page 33
SCHEMA TIC DIAGRAM - 9 (U : TUNER)
– 33 –
Page 34
WIRING - 8 (EZ: TUNER)
101112131415161718192021222324
1234567892526272829303132
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
-34-
Q
R
S
T
U
Page 35
SCHEMATIC DIAGRAM - 10 (EZ : TUNER)
– 35 –
Page 36
WIRING - 9 (DECK/RELAY)
101112131415161718192021222324
1234567892526272829303132
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
-36-
Q
R
S
T
U
Page 37
IC BLOCK DIAGRAM
IC, LC72131D
IC, BU1920FS
IC, BA3880FS
IC, BA7762AFS
– 37 –
Page 38
IC, BU4094BCF
IC, MM1454XFBE
IC, CXA1553P
IC, M62495FP
– 38 –
Page 39
IC, LA1837NL
– 39 –
Page 40
ADJUSTMENT (TUNER / DECK / MAIN)
C
TUNER C.B
G TUNER C.B <EZ ONLY>
3
5
6
8
10
11
4
3
5
< TUNER SECTION >
L981
1
TP8
(LCH)
FFE801
(GND)
TC942
CN701
TP9
(RCH)
L942L941
TP2(CLK)
TP1(VT)
7
12
L772
64
9
TP4(DC)TP3(DC)
IC771
1
L771
9
1. Clock Frequency Check
Settings : • Test point : TP2 (CLK)
Method : Set to MW 1602kHz and check that the test
point is 2052kHz ± 45Hz.
2. MW VT Check
Settings : • Test point : TP1 (VT)
Method : Set to MW 1602kHz and check that the test
point is less than 8.0V. Then set to MW
531kHz and check that the test point is more
than 0.6V.
3. MW Tracking Adjustment
Settings : • Test point : TP8 (Lch), TP9 (Rch)
• Adjustment location :L981 (1/3)
Method : Set to MW 999kHz and adjust L981 (1/3) so
that the test point becomes maximum.
4. LW VT Adjustment
Settings : • Test point : TP1 (VT)
• Adjustment location :L942
Method : Set to LW 144kHz and adjust L942 so that the
test point becomes 1.3V ± 0.05V.
Then set to LW 290kHz and check that the test
point is less than 8.0V.
5. LW Tracking Adjustment
Settings : • Test point : TP8 (Lch), TP9 (Rch)
• Adjustment location :
L941 ........................... 144kHz
TC942......................... 290kHz
Method : Set up TC942 to center before adjustment.
The level at 144kHz is adjusted to maximum
by L941. Then the level at 290kHz is adjusted
to maximum by TC942.6.
6. AM IF Adjustment
Settings : • Test point : TP8 (Lch), TP9 (Rch)
• Adjustment location :
L772 ........................... 450kHz
7. FM VT Check
Settings : • Test point : TP1 (VT)
Method : Set to FM 108.0MHz and check that the test
point is less than 8.0V. Then set to FM
87.5 MHz and check that the test point is more
than 0.5V.
8. FM Tracking Check
Settings : • Test point : TP8 (Lch), TP9 (Rch)
Method : Set to FM 98.0MHz and check that the test
point is less than 13dBµV.
9. DC Balance / Mono Distortion Adjustment
Settings : • Test point : TP3,TP4 (DC balance)
TP8 (Lch), TP9 (Rch) (Distortion)
• Adjustment location :L771
• Input level : 60dBµV
Method : Set to FM 98.0MHz and adjust L771 so that
the voltage between TP3 and TP4 becomes
0V ± 0.04V.
Next, check that the distortion is less than
1.3%.
– 40 –
Page 41
D
TUNER C.B
G TUNER C.B <U ONLY>
CN701
GND
10
TP6
(LCH)
12
TP7
TP7
(RCH)
(RCH)
7
3
5
6
TP3
(DC BALANCE)
TP4
(DC BALANCE)
7
L981
30
TP2
(CLK)
1
IC771
L771
(1/3)
3
FFE801
TP1 (VT)
4
2
4
L772
6
7
< TUNER SECTION >
1. Clock Frequency Check
Settings : • Test point : TP2 (CLK)
Method : Set to AM 1710kHz and check that the test point is
2160kHz ± 45Hz.
2. AM VT Check
Settings : • Test point : TP1 (VT)
Method : Set to AM 1710kHz and AM 530kHz and check
that the test point is less than 8.5V (1710kHz) and
more than 0.6V (530kHz).
3. AM Tracking Adjustment
Settings : • Test point : TP6 (Lch), TP7 (Rch)
• Adjustment location :
L981 (1/3) ..................................... 1000kHz
Method : Set to AM 1000kHz and adjust L981 (1/3) so that
the test point is maximum.
4. FM VT Check
Settings : • Test point : TP1 (VT)
Method : Set to FM 108.0MHz and check that the test point is
less than 8.0V.
Set to FM 87.5MHz and check that the test point is
more than 0.5V.
5. FM Tracking Check
Settings : • Test point : TP6 (Lch), TP7 (Rch)
Method : Set to FM 98.0MHz and check that the test point is
less than 9.0dBµV.
6. AM IF Adjustment
Settings : • Test point : TP6 (Lch), TP7 (Rch)
• Adjustment location :
L772 ................................................450kHz
7. DC Balance / Mono Distortion Adjustment
Settings : • Test point : TP3, TP4 (DC Balance)
TP6 (Lch), TP7 (Rch) (Distortion)
• Adjustment location : L771
• Input level : 60dBµV
Method : Set to FM 98.0MHz and adjust L771 so that the
voltage between TP3 and TP4 becomes 0V ± 0.04V.
Next, check that the distortion is less than 1.3%
– 41 –
Page 42
A
MAIN C.B
CN901
IC101
GND
9
SFR305
IC302
TP1
SFR351
4
SFR303
SFR304
L101
9
C
TAPE C.B
1
2
3
4
5
6
7
8
GND
TP9 (RCH)
TP8 (LCH)
7
SFR306
H
DECK C.B
SFR1
1
CNA1
SFR352
SFR352
5
DECK R / P / E HEAD
2
– 42 –
Page 43
< DECK SECTION >
1. Tape Speed Adjustment
Settings : • Test tape : TTA–100
• Test point : TP8 (Lch), TP9 (Rch)
• Adjustment location : SFR1
Method : Play back (FWD) the test tape and adjust SFR1 so
that the frequency counter reads 3000Hz ± 5Hz and
± 45Hz (REV) with respect to forward speed.
2. Head Azimuth Adjustment
Settings : • Test tape : TTA–300
• Test point : TP8 (Lch), TP9 (Rch)
• Adjustment location :Head azimuth
adjustment screw
Method : Play back (FWD) the 10kHz signal of the test tape
and adjust screw so that the output becomes
maximum. Next, perform on REV play mode.
3. PB Frequency Response Check
Settings : • Test tape : TTA–300
• Test point :TP8 (Lch), TP9 (Rch)
Method : Play back the 315Hz and 10kHz signals of the test
tape and check that the output ratio of the 10kHz
signal with respect to that of the 315Hz signal is
0dB ± 2dB.
4. PB Sensitivity Adjustment
Settings : • Test tape : TTA–200
• Test point : TP8 (Lch), TP9 (Rch)
• Adjustment location : SFR303 (Lch)
SFR304 (Rch)
Method : Play back the test tape and adjust SFRs so that the
output level of the test point is 245mV.
5. REC/PB Frequency Response Adjustment
Settings : • Test tape : TTA–602
• Test point : TP8 (Lch), TP9 (Rch)
• Input signal : 1kHz / 10kHz (LINE IN)
• Adjustment location : SFR351 (Lch)
SFR352 (Rch)
Method : Apply a 1kHz signal and REC mode. Then adjust
OSC attenuator so that the output level at the TP8,
TP9 becomes 0dB (17mV). Record and play back the
1kHz and 10kHz signals and adjust SFRs so that the
output of the 10kHz signals becomes 0dB ± 0.5dB
with respect to that of the 1kHz signal.
6. REC/PB Frequency Response Check
Settings : • Test tape : TTA–615
• Test point : TP8 (Lch), TP9 (Rch)
• Input signal : 1kHz / 10kHz (LINE IN)
Method : Apply a 1kHz signal and REC mode. Then adjust
OSC attenuator so that the output level at the TP8,
TP9 becomes 0dB (17mV). Record and play back the
1kHz and 10kHz signals and check that the output of
the 10kHz signals is 0dB ± 2dB with respect to that of
the 1kHz signal.
7. REC/PB Sensitivity Adjustment
Settings : • Test tape : TTA–602
• Test point : TP8 (Lch), TP9 (Rch)
• Input signal : 1kHz (LINE IN)
• Adjustment location : SFR305 (Lch)
SFR306 (Rch)
Method : Apply a 1kHz signal and REC mode. Then adjust
OSC attenuator so that the output level at TP8, TP9
becomes 0dB (170mV). Record and play back the
1kHz signals and adjust SFRs so that the output
becomes 0dB ± 0.5dB.
8. REC/PB Sensitivity Check
Settings : • Test tape : TTA–615
• Test point : TP8 (Lch), TP9 (Rch)
• Input signal : 1kHz (LINE IN)
Method : Apply a 1kHz signal and REC mode. Then adjust
OSC attenuator so that the output level at TP8, TP9
becomes 0dB (170mV). Record and play back the
1kHz signals and check that the output is 0dB ± 1.5dB.
< MAIN SECTION >
9. µ-CON OSC Adjustment
Settings : • Test point : TP1 and GND
• Adjustment location : L101
Method : Insert AC plug with pressing of DISPLAY key. Adjust
L101 so that the frequency across the test point is
97.258Hz ± 0.098Hz.
– 43 –
Page 44
IC DESCRIPTION
IC, LC876580W-5N98
Pin No. Pin Name I/O Description
1 I-STEREO (TU) I Tuner stereo detection input.
2 I-TUDO (TU) I Connect to tuner PLL IC, LC72131D Pin 6 (DO).
3 I-RDSDATA (TU) I RDS data input. (EZ only)
4 O-ARDY (MD) O
5 O-STB (M) O Main shift registor: latch output.
Serial data for MD unit control reception / transmission ready output.
(Not used)
6 O-CLK O
7 O-DATA O
8 O-VOLCTL O Connect to Function VOL IC, M62495FP pin 13 (CONT).
9 I-TMBASE I Reference clock input. Connect to LC72131D Pin 7 (T-BASE).
10 O-CLK SHIFT O Clock shift control output.
11 I-RESET I MICON reset input.
12 I-ACOFF I Hold status detection input.
I-TU SIG /
13
I-MS (TU / TP) (Not used)
14 VSS 1 - GND.
15 CF 1 - Connect to 9.43MHz crystal oscillation.
16 CF 2 - Connect to 9.43MHz crystal oscillation.
17 VDD 1 - MICON power supply (+5V).
18 I-LEVEL I Level meter input (AD).
19 I-KEY1 I Key 1: AD input.
20 I-KEY0 I Key 0: AD input.
21 I-MODE SW (TP) I Deck mechanical status detection input (AD).
Front shift registor BU4094BCF (reversal) and tuner PLL IC, LC72131D combination clock output.
Front shift registor BU4094BCF (reversal) and tuner PLL IC, LC72131D combination data output.
AD for RDS signal level input. (EZ only) / Tape music sensor input.
I
22 O-STB (F) O Front shift registor BU4094BCF latch reversal output.
23 I-JOG1 I AD input from multi jog rotary encoder output A/B.
24 O-BBEB O BBE control reversal output (B).
25 O-CE (TU) O Tuner PLL IC, LC72131D chip enable output.
26 O-BBEA O BBE control reversal output (A).
27 I-RDS CLK (TU) I RDS clock input. (EZ only)
28 O-LMUTE O Line mute output. (Not used)
29 I-REM I Remote controller input.
30 ~ 45 NC - Not connected.
46 VDD3 - MICON power supply (+5V).
47 I-CLS (MD) I
48 ~ 57 NC - Not connected.
58 I-SWCLS (TP) I Deck mechanical status detection input (SWCLS).
59 I-SWOPN (TP) I Deck mechanical status detection input (SWOPN).
60 I-AUTO (TP) I Deck mechanical status detection input (AUTO).
61 I-CAM (TP) I Deck mechanical status detection input (CAM).
MD unit close detection SW input / Close at L. (Connected to GND through a
resistor)
– 44 –
Page 45
Pin No. Pin Name I/O Description
62 MD / TAPE I Initial matrix input (L: MD / H: TAPE).
63 RDS I
64 BBE I Initial matrix input (L: BBE).
65 DOLBY I Initial matrix input (L: DOLBY).
66 AM10K I Initial matrix input (H: 10K STEP / L: 9K STEP).
67 FM WIDE&AMST I Initial matrix input (H: FM WIDE & AM STEREO).
68 LW I Initial matrix input (H: LW) (EZ only) / Connect to GND through a resistor. (U only)
69 SW I Initial matrix input (H: SW). Connect to GND through a resistor.
70 OIRT I Initial matrix input (H: OIRT). Connect to GND through a resistor.
71 I-CDSRQ (CD) I CD data transmission request signal input.
72 VDD4 - MICON power supply (+5V).
73 O-CDON (CD) O CD power supply control output. (Not used)
74 O-D MS CD (CD) O Transmission output to CD MICON.
75 O-CS (CD) O Data transmission request output to CD MICON.
76 O-SCK (CD) O Data reception and transmission clock output to CD MICON.
77 O-SLP (CD) O Sleep output to CD MICON.
78 O-RST (CD) O Reset output to CD MICON.
79 I-SWCD I CD disc detection switch (H: active).
80 I-D CD MS (CD) I Transmission data from CD MICON.
Initial matrix input (H: RDS) (EZ only) / Connect to GND through a resistor.
(U only).
81 O-QSURR O Q-Surround IC control output.
82 O-TUON (TU) O Tuner power supply switch output.
83 O-MOTOR (TP) O Deck mechanical motor control output.
84 O-SWSCAN O Tuner test mode TP (used for coil adjustment point).
85 O-SREQ (MD) O Serial data for MD unit control transmission request. (Not used)
86 O-MD REC O Output H at MD REC.
87 O-P.ON O Power on output.
88 O-RST (MD) O MD unit reset signal output. (Not used)
89 VSS2 - GND.
90 VDD2 - MICON power supply (+5V).
91 O-OE (FL) O Output function output to FL driver.
92 O-LAT (FL) O Latch output to FL driver.
93 O-MUTE O Main mute output.
94 O-PL (TP) O Deck mechanical plunger control output.
95 I-SI (FL) I Serial data input to FL driver.
96 O-MREQ (MD) O Serial data for MD unit control transmission request output. (Not used)
97 O-CLK (FL) O Clock output to FL driver.
98 O-SIN (MD) O Serial data for MD unit control output. (Not used)
99 I-SOUL (MD) I Serial data for MD unit control input. Connected to GND through a resistor.
100 I-ACLK (MD) I Serial data for MD unit control input. Connected to GND through a resistor.
– 45 –
Page 46
CD TEST MODE
1. How to activate CD Test Mode
Insert the AC plug while pressing the “Enter” button.
FL display is fully illuminated and test mode will be
activated. Insert the test disc and operate the test
mode following the control method as shown below.
Note:If no CD was inserted, it displays “No Disc”
and cannot be operated.
2. How to cancel CD Test Mode
Either one of the following operations will cancel the
CD test mode.
• Disconnect the AC plug.
• Press “Function” button.
• Press “Power” button.
• Press “Band” button.
3. CD Test Mode functions
When test mode is activated, the following mode functions can be used by pressing the operation keys.
Mode
Func-
FL Display
Operation
Content
tion
Start Mode
Button
Fully
• Initialization
illuminate
Sled Mode
r
t
CD TEST
• Shift to the external circumference of
Pick-Up. * Note 1
• Shift to the internal circumference of
• SLED SERVO
• SLED Operation Check
Pick-Up. (Normal operation during
CD PLAY)
Search Mode
s
CD
• LASER DIODE illuminated all the
time (CD block power ON)
• Continuous Focus Search *Note 2
(Pickup lense repeat full swing)
• APC circuit check
• Laser current measurement
• Focus search waveform check
• Focus error waveform check (In
Search Mode, FOK/FZC is not
checked)
Play Mode
c
1Tr.0:01
• Normal Playback
• When TOC READ is unavailable
Continue focus search *Note 2
• Continue spindle motor kick spin
• FOCUS SERVO/TRACKING
SERVO
• CLV SERVO/SLED SERVO
• FOK check
• RF waveform check
Traverse Mode
a
1Tr.0:01
• Tracking servo OFF/ON
• Repeat OFF/ON every time [a]
• TRACKING SERVO OFF
• Tracking Balance Check
button is pressed
* Note 1 : When pressing the r or t keys, take care to avoid damage to the gears. Because the sled motor is
activated when the r or t keys are pressed, even when the pick-up is at outermost or innermost
track. The sled operation is not as normal and moves outermost track with r button and innermost
track with t button
* Note 2 : There are cases when the tracking servo cannot be locked owing to the protection circuit being operated
when heat builds up in the driver IC if the focus search is operated continually for more than 10 minutes.
In these case, the power supply should be switched off for an hour until heat has been reduced and then
re-start.
4. The Operation Outline
This operation of each mode is carried out in the direction of the arrows from the start mode as indicated in the
following illustration
Start mode
illuminate fully
s
Display
s
a
Traverse modeSearch mode
l
l
Play mode
s
a
– 46 –
Page 47
FL (9-ST-19GONK) GRID ASSIGNMENT AND ANODE CONNECTION
GRID ASSIGNMENT
– 47 –
Page 48
ANODE CONNECTION
– 48 –
Page 49
– 49 –
Page 50
MECHANICAL EXPLODED VIEW 1 / 1
Q
25
26
31
27
V
21
40
39
38
g
37
2ZM-1
63
30
28
29
g
B
22
A
24
23
O
36
32
e
C
19
20
R10NM
U
c
41
42
e
35
33
58
PLATE,SHLD
17
18
14
16
15
64
43
CC
J
N
P.W.B
P.W.B
I
44
P
C
62
FL101
34
P.W.B
a
H
HT-SINK
45
46
N
C
P.W.B
47
R
R
S
F
C
C
f
K
C
HT-SINK
K
52
F
HT-SINK
C
M
65
P.W.B
R
f
C
C
51
48
N
49
N
L
54
50
b
T
P
D
55
F
F
SH,SHLD A
TN-CCD1001-902M
G
13
O
8
12
53
8
11
10
9
a
CHAS,MAIN
– 50 –
d
60
61
b
7
P.W.B
6
1
3
2
E
5
G
F
4
57
C
56
SH,CD COVER
66
58
59
c
d
F
P.W.B
C
Page 51
MECHANICAL PARTS LIST 1 / 1
PART NO.
NO.
1 8A-CJ5-016-010 KNOB,RTRY JOG
2 8A-CJ5-217-010 PLATE,JOG
3 8A-CJ5-017-010 REFLECTOR,JOG
4 8A-CL5-037-010 PANEL,FR CASS EZ<EZ>
4 8A-CL5-023-010 PANEL,FR CASS(B)<U>
5 8A-CJ5-019-010 LENS,SENSOR
6 8A-CJ5-007-010 WINDOW,DISPLAY<U>
6 8A-CJ5-033-010 WINDOW,DISPLAY EZ<EZ>
7 8A-CL5-006-010 CABI,FR EZ<EZ>
7 8A-CL5-021-010 CABI,FR(B) U<U>
8 8A-CJ5-012-010 KEY,ENTER
9 8A-CL5-046-010 DUST COVER, CD FELT<U>
9 8A-CJ5-023-010 DUST COVER, CD FELT<EZ>
10 8A-CJ5-018-010 REFLECTOR,CD
11 8A-CJ5-215-010 GUIDE,LED CD
12 8A-CL5-025-010 KEY,SKIP CASS
13 8A-CL5-009-010 KEY,PLAY CASS
14 8A-CJ5-013-010 KEY,EJECT CD
15 8A-CL5-305-010 PLATE,BOX LOCK
16 8A-CL5-326-010 SPR-E,OPEN
17 8A-CJ5-014-010 BTN,OPEN
18 8A-CL5-312-010 HLDR,BUTTON
19 8A-CJ5-009-010 KEY,POWER
20 8A-CJ5-015-010 REFLECTOR,POWER
21 8A-CL5-302-010 LEVER,POP-UP
22 8A-CL5-323-010 SPR-P,LOCK
23 8A-CL5-324-010 PLATE,LOCK
24 8A-CL5-307-010 BOX,CASS<EZ>
24 8A-CL5-328-010 BOX,CASS(B)<U>
25 8A-CL5-321-010 SPR-P,CAS PUSH R
26 8A-CL5-315-010 SPR-E,POP UP
27 8A-CL5-301-010 GEAR,POP-UP2
28 8A-CL5-317-010 GEAR,DUMP
29 8A-CL5-316-010 SPR-T,CASS
30 8A-CL5-306-010 PLATE,ASSY POP-UP
31 8A-CL5-040-010 LID,CASS<EZ>
31 8A-CL5-024-010 LID,CASS(B)<U>
32 8A-CL5-201-010 HLDR,FR
33 8A-CL5-202-010 HLDR,REAR
34 8A-CL5-625-010 CONN ASSY,8P -RPB
35 8A-CL5-002-010 CABI,TOP<EZ>
35 8A-CL5-022-010 CABI,TOP(B) U<U>
36 8A-CL5-313-010 SPR-T,BOX LOCK
37 8A-CL5-308-010 LEVER,BOX LOCK
38 8A-CL5-309-010 PLATE,GUIDE
39 8A-CL5-322-010 SHAFT,TURN
40 8A-CL5-310-010 LEVER,TURN
41 8A-CL5-325-010 SPR-C,TURN
42 87-067-729-010 PW 1.3-4.0-0.25 C-SLT
43 8A-CL5-627-010 CABLE,FFC9P-1.0 220
44 8A-CL5-628-010 CABLE,FFC14P-1.0 160
45 8A-CJ5-004-010 PANEL,SIDE L<EZ>
45 8A-CL5-028-010 PANEL,SIDE L(B) U<U>
46 8A-CL5-626-010 CABLE,FFC15P-1.0 220
47 8A-CJ5-634-010 CONN ASSY,2P SHLD
PART NO.DESCRIPTIONREF. NO. KANRI
48 8A-CL5-005-010 CABI,REAR EZ<EZ>
48 8A-CL5-030-010 CABI,REAR(B) U<U>
49 8Z-CL1-663-010 FAN,MF40D-12-200MM
!
50 8A-CJ5-622-010 PT,ACJ-5 EZ<EZ>
!
50 8A-CJ5-621-010 PT,ACJ-5 U<U>
51 8A-CJ5-219-010 HLDR,TR B
52 8A-CJ5-206-010 HLDR,CD B
53 8A-CJ5-205-010 HLDR,CD A
54 8A-CJ5-005-010 PANEL,SIDE R<EZ>
54 8A-CL5-029-010 PANEL,SIDE R(B) U<U>
55 8A-CJ5-213-010 HLDR,MECHA CD
!
56 87-A80-092-010 AC CORD ASSY,E BLK SUN FAI<EZ>
!
56 87-A80-110-010 AC CORD ASSY,U SPT-2W<U>
57 87-085-185-010 BUSHING, AC CORD (E)<EZ>
57 87-085-189-010 BUSHING, CORD (U)<U>
58 87-064-185-010 HLDR,WIRE
59 8A-CJ5-204-010 HLDR,ECO
60 8Z-NB8-240-010 COVER, PL
61 8Z-CE3-206-010 CUSH,PL 9.2-4.2-5
62 8A-CJ5-209-010 GUIDE,FL
63 8A-CL5-311-010 LEVER,EJECT
64 87-NF8-220-010 DMPR,150
65 88-805-051-420 CONN ASSY,5P 140
66 88-805-040-820 CONN ASSY,4P 80
A 87-265-544-310 V+2-2.2 NI
B 87-352-509-310 VT2+1.4-4
C 87-067-579-010 TAPPING SCREW, BVT2+3-8
D 87-067-421-010 VTT+2-4
E 88-AR1-217-010 S-SCREW,BFT2+3-8
F 87-067-688-010 BVTT+3-6
G 87-591-094-010 QIT+3-6 GOLD
H 87-NF4-224-010 S-SCREW,IT3B+3-8CU
I 88-ZG5-302-010 S-SCREW,8ZG-5+2-4W/O
J 8A-CL5-327-010 S-SCREW,2.6-11
K 87-067-584-010 BVT2+3-3-6W/O SLOT
L 87-078-191-010 S-SCREW,IT+4-10
M 87-751-098-410 VT2+3-14W/O SLOT
N 87-067-660-010 BVT2+3-8W/O SLOT BLK
O 87-591-094-410 TAPPING SCREW, QIT+3-6
P 87-067-641-010 UTT2+3-8W/O SLOT BLK
Q 87-067-868-010 V+1.7-4 HL BLK
R 87-067-703-010 BVT2+3-10W/O SLOT
S 87-067-579-080 BVT2+3-8W/O SLOT
T 87-067-767-010 BVTT+2.6-6
U 82-ZM3-220-010 S-SCREW,SHILD PLATE
V 87-351-547-310 VT2+2-3 BLK
NO.
DESCRIPTIONREF. NO. KANRI
COLOR NAME TABLE
Basic color symbol Color Basic color symbol Color Basic color symbol Color
B Black C Cream D Orange
G Green H Gray L Blue
LT Transparent Blue N Gold P Pink
R Red S Silver ST Titan Silver
T Brown V Violet W White
WT Transparent White Y Yellow YT Transparent Yellow
LM Metallic Blue LL Light Blue GT Transparent Green
LD Dark Blue DT Transparent Orange GM Metallic Green
YM Metallic Yellow DM Metallic Orange
– 51 –
Page 52
TAPE MECHANISM EXPLODED VIEW 1 / 1
A
B
A
B
29
48
47
46
30
31
32
33
34
45
35
35
44
36
43
HLDR,MOTOR
42
HLDR,IC
SH
P.C.B
40
39
38
41
37
C
C
G
CAPSTAN
CAPSTAN
D
D
E
E
49
H
F
10
C
C
13
11
A
12
A
B
14
15
16
9
8
17
7
2
HLDR WIRE 3
18
6
A
4
3
5
22
19
23
28
24
25
20
21
20
P.C.B
1
A
26
27
– 52 –
Page 53
TAPE MECHANISM PARTS LIST 1 / 1
PART NO.
NO.
1 82-ZM1-327-310 CHAS ASSY,RM
2 82-ZM1-258-210 SPR-T,PINCH L
3 82-ZM1-341-210 LVR ASSY,PINCH L2
4 82-ZM1-266-310 LVR,DIR
5 82-ZM1-214-010 SPR-T,DIR
6 82-ZM1-333-210 PLATE,LINK2
7 82-ZM1-269-210 SPR-T,BRG
8 82-ZM1-219-110 SPR-T,LINK
9 82-ZM1-210-110 GEAR,H T
10 82-ZM3-353-010 SPR-T,HEAD 2
11 82-ZM1-298-010 SPR-P EARTH
12 82-ZM1-314-110 PLATE,HEAD
13 87-A91-176-010 HEAD,RPH HADKH56
14 82-ZM1-208-310 HLDR,HEAD
15 82-ZM1-207-910 GUIDE,TAPE
16 82-ZM1-218-010 SPR-E,HB
17 82-ZM1-206-910 CHAS,HEAD
18 82-ZM1-222-310 LVR,PLAY(*)
19 82-ZM1-217-410 REEL TABLE
20 82-ZM1-240-110 LVR,REC(*)
21 82-ZM1-257-010 SPR-T,CAS
22 82-ZM1-285-410 SPR-C,BT L
23 82-ZM1-244-510 SPR-C,BT
24 82-ZM1-242-010 LVR,CAS
25 82-ZM1-243-010 LVR,STOP
26 82-ZM1-344-210 LVR ASSY,PINCH R2
27 82-ZM1-259-210 SPR-T,PINCH R
28 82-ZM1-241-310 LVR,MC
29 82-ZM1-255-310 SPR-E,LVR DIR
30 82-ZM1-221-310 GEAR,CAM(*)
PART NO.DESCRIPTIONREF. NO. KANRI
NO.
31 82-ZM1-224-410 LVR,FR
32 82-ZM1-227-310 LVR,TRIG
33 82-ZM1-305-210 SPR-E,TRIG 2
34 82-ZM1-225-210 GEAR,FR
35 82-ZM1-216-510 GEAR,REEL
36 82-ZM1-226-010 GEAR,REW
37 82-ZM1-338-110 BELT,FR 4
38 82-ZM1-348-110 FLY-WHL,L W
39 82-ZM1-349-110 FLY-WHL,R W
40 82-ZM1-354-010 BELT,SBU MAIN2 EPDM
41 82-ZM1-636-010 CONN ASSY,9P
42 87-045-347-010 MOT,SHU2L 70
43 82-ZM1-247-210 PULLEY,MOTOR
44 82-ZM1-223-010 GEAR,PLAY
45 82-ZM3-333-310 SLIP DISK ASSY 2
46 82-ZM3-616-010 RING MAGNET 4
47 82-ZM1-220-210 GEAR,IDLER
48 82-ZM1-322-010 SPR-T,FR 60
49 82-ZM1-635-010 SOL ASSY,23
A 82-ZM1-283-310 S-SCREW,AZIMUTH
B 82-ZM1-315-010 S-SCREW GUIDE TAPE
C 80-ZM6-207-010 V+1.6-7
D 87-741-073-410 UT2+2.6-6 GLD
E 87-251-070-410 U+2.6-3
F 82-ZM3-334-010 PW 2.16-6-0.4
G 87-B10-008-010 W-P,2.08-8-0.4-SLIP
H 80-ZM6-243-010 SH 1.75-3.6-0.5 SLT
DESCRIPTIONREF. NO. KANRI
– 53 –
Page 54
CD MECHANISM EXPLODED VIEW 1 / 1
40
50
41
B
H
H
43
B
45
46
44
B
H
67
P. C . B
DET SW
DET SW
29
8
30
9
13
37
38
31 32
39
28
36
31
14
A
47
49
50
51
52
63
58
A
59
64
A
48
56
55
57
A
60
61
62
15
34
64
33
35
44
A
53
54
A
A
D
A
66
F
A
D
A
A
59
65
7
8
23
10
11
2
1
C
6
4
DET SW
3
5
I
B
P. C . B
12
20
H
22
43
E
18
17
16
G
43
42
44
19
FD GR(C)
24
21
22
25
26
I
H
H
27
– 54 –
Page 55
CD MECHANISM PARTS LIST 1 / 1
PART NO.
NO.
1 S3-031-110-030 EARTH SPR
2 S3-031-110-180 L.P SPRING(L)
3 S3-031-110-010 FRONT BRKT
4 S3-031-113-010 LDG MOTOR ASSY
5 S3-031-110-190 L.P SPRING(R)
6 S3-031-110-050 SUPPORT PL
7 S3-031-110-080 GR MT BLK
8 S9-W03-302-760 NW BLUE 2.9-5-0.3
9 S3-031-110-360 LDG ROLLER(P)
10 S3-031-110-100 LDG GR(3)
11 S3-031-110-090 LDG GR(2)
12 S3-031-110-290 LDG BELT
13 S3-031-113-020 LDG RLR SFT ASSY
14 S9-W07-250-300 LUMIL AR W 2.3-9.8-0.25
15 S3-031-110-120 LDG GR(5)
16 S3-031-050-300 NUT PUSH SPR PL(M)
17 S3-031-050-290 PU M NUI(M)
18 S6-904-160-010 PICK-UP VED0375-TN
19 S3-031-053-040 FEED SCREW(M)ASSY
20 S3-031-050-320 PU SHAFT(M)
21 S3-031-050-330 THRUST SPR(M)
22 S3-031-050-210 LOCK PIN
23 S3-031-050-220 LOCK PIN BL
24 S3-031-050-760 F.M. BASE(A)
25 S3-031-053-010 FEED MOTOR ASSY
26 S3-031-050-280 FD GR BLK(M)
27 S3-030-050-100 PU GEAR(B)
28 S3-031-010-570 UPPER PL(A)
29 S3-031-110-240 SW ACTR
30 S3-031-010-090 SEL ARM (L)
31 S3-031-010-110 S ARM SPRING
32 S3-031-010-080 SEL STOP PL
33 S3-031-010-100 SEL ARM (R)
34 S3-031-010-250 S.L ARM SPRING
35 S3-031-010-240 S.L ARM
36 S3-031-010-580 FIX ARM(R)A
37 S3-031-010-380 LDG GR(6)B
38 S3-031-010-220 LDG GR(6)SPRING
39 S3-031-010-370 FIX PL(R)B
40 S3-031-010-340 FIX ARM(L)B
PART NO.DESCRIPTIONREF. NO. KANRI
NO.
41 S3-031-010-500 FIX PL(L)Z
42 S3-031-050-310 FD SCREW(M)
43 S3-031-010-520 HUNG UP SPRING(A)
44 S3-031-050-240 DAMPER(J)
45 S3-031-010-020 REAR D BRKT
46 S3-031-010-150 TRIG PL SPRING
47 S3-031-010-160 TRIG ARM
48 S3-031-010-120 TRIG LVR
49 S3-031-010-140 TRIG PL
50 S3-031-010-030 DAMPER PIN
51 S3-031-050-360 STOPPER SPR
52 S3-031-050-190 8CM STOPPER SPR PL
53 S3-031-050-230 CLAMPER PLATE
54 S3-031-050-150 CLAMPER
55 S3-031-050-740 CLP ARM(A)
56 S3-031-050-410 8CM STOPPER(M)
57 S3-031-050-140 CLP ARM SPRING
58 S3-031-050-250 CLP ARM SPR(L)
59 S3-031-050-700 D.S ARM COLLAR
60 S3-031-050-720 SP COLLAR
61 S3-031-050-710 D.S ARM SPR
62 S3-031-055-010 DISC SUPPORT ARM ASSY
63 S9-W02-500-900 PW CUT 2.1-4-0.5
64 S3-031-010-530 HUNG DOWN SPRING(A)
65 S3-031-053-050 SPINDLE MOTOR(M)ASSY
66 S3-031-050-730 T.T.BASE(A)
67 S3-031-010-010 FRAME
A 87-841-034-410 CAMERA B TAPPING SCREW M2-5
B 87-741-033-410 CAMERA SCREW TS.G M2-4
C S9-C04-205-030 CAMERA S TAPPING SCREW M2-5
D 87-267-525-310 CAMERA SCREW M1.7-2.2
E 87-263-036-010 CAMERA TAPPING SCREW B 3 M2-8
F S9-C42-202-010 CAMERA TAPPING SCREW S 3 M2-2
G S9-C45-175-030 CAMERA TAPPING SCREW P3 M1.7-5
H 87-351-549-310 CAMERA TAPPING SCREW B 3 M2-4
I S9-P02-200-310 TAMS SCREW M2-3
DESCRIPTIONREF. NO. KANRI
– 55 –
Page 56
SPEAKER DISASSEMBLY INSTRUCTIONS
Type.1
Insert a flat-bladed screwdriver into the position indicated by the
arrows and remove the panel. Remove the screws of each speaker
unit and then remove the speaker units.
Type.2
Remove the grill frame and four pieces of rubber caps by pulling
out with a flat-bladed screwdriver. Remove the screws from hole
where installed rubber caps. Insert a flat-bladed screwdriver into
the position indicated by the arrows and remove the panel. Remove the screws of each speaker unit and then remove the speaker
units.
Type.4
TOOLS
1 Plastic head hammer
2 1 flat head screwdriver
3 Cut chisel
123
How to Remove the PANEL, FR
1. Insert the (() flat head screwdriver tip into the gap between
the PANEL, FR and the PANEL, SPKR. Tap the head of
the (() flat head screwdriver with the plastic
and create the clearance as shown in Fig-1.
2. Insert the cut chisel in the clearance, and tap the head of
the cut chisel with plastic hammer as shown in Fig-2, to
remove the PANEL, FR.
hammer head,
Type.3
Insert a flat-bladed screwdriver into the position indicated by the
arrows and remove the panel. Turn the speaker unit to counterclockwise direction while inserting a flat-bladed screwdriver into
one of the hollows around speaker unit, and then remove the speaker
unit. After replacing the speaker unit, install it turning to clockwise
direction until "click" sound comes out.
3. Place the speaker horizontally. Tap head of the cut chisel
with plastic hammer as shown in Fig-3, and remove the
PANEL, FR completely.
Fig-1 Fig-2
How to Attach the PANEL, FR
Attach the PANEL, FR to the PANEL, SPKR. Tap the four
corners of the PANEL, FR with the plastic hammer to fit the
PANEL, FR into the PANEL, SPKR completely.
– 56 –
Fig-3
Page 57
SPEAKER PARTS LIST <SX-MS7>
PART NO.
NO.
1 8A-CJ5-422-010 GRILLE,FRAME ASSY Y<EZ>
1 8A-CL5-404-010 GRILLE,FRAME ASSY B<U>
2 8A-CJ5-409-010 FASTENER
3 8A-CJ5-405-010 PANEL,SP<EZ>
3 8A-CL5-408-010 PANEL,SP B<U>
4 8A-CJ5-417-010 SPKR, TW 25
5 8A-CJ5-411-010 SPKR, W 87S<EZ>
5 8A-CL5-406-010 SPKR, W 87SI<U>
6 8A-CJ5-403-010 PANEL,FR<EZ>
6 8A-CL5-403-010 PANEL,FR B<U>
7 8Z-SSM-005-010 BOSS,CATCHER
DESCRIPTIONREF. NO. KANRI
ACCESSORIES / PACKAGE LIST
PART NO.
NO.
1 8A-CL5-913-010 IB,U(ESF)M<U>
1 8A-CL5-916-010 IB,EZ(9L)M<EZ>
2 8A-CL5-950-010 RC-AAT03<EZ>
2 8A-CL5-954-010 RC UNIT,RC-ATT03(B)<U>
3 87-006-225-010 ANT,LOOP ANT NC2
4 87-A90-118-010 ANT,WIRE FM(Z)<EZ>
4 87-043-115-010 ANT,FEEDER FM<U>
DESCRIPTIONREF. NO. KANRI
– 57 –
Page 58
2–11, IKENOHATA 1–CHOME, TAITO-KU, TOKYO 110, JAPAN TEL:03 (3827) 3111
Printed in Singapore9301978 0251431
Loading...