PROTECTION OF EYES FROM LASER BEAM DURING SERVICING
This set employs laser. Therefore, be sure to follow carefully
the instructions below when servicing.
WARNING!!
WHEN SERVICING, DO NOT APPROACH THE LASER
EXIT WITH THE EYE TOO CLOSELY. IN CASE IT IS
NECESSARY TO CONFIRM LASER BEAM EMISSION.
BE SURE TO OBSERVE FROM A DISTANCE OF MORE
THAN 30cm FROM THE SURFACE OF THE OBJECTIVE LENS ON THE OPTICAL PICK-UP BLOCK.
s Caution: Invisible laser radiation when
open and interlocks defeated avoid
exposure to beam.
s Advarsel: Usynlig laserståling ved åbning,
når sikkerhedsafbrydere er ude af funktion.
Undgå udsættelse for stråling.
VAROITUS!
Laiteen Käyttäminen muulla kuin tässä käyttöohjeessa
mainitulla tavalla saataa altistaa käyt-täjän
turvallisuusluokan 1 ylittävälle näkymättömälle
lasersäteilylle.
VARNING!
Om apparaten används på annat sätt än vad som
specificeras i denna bruksanvising, kan användaren
utsättas för osynling laserstrålning, som överskrider
gränsen för laserklass 1.
CAUTION
Use of controls or adjustments or performance of procedures other than those specified herin may result in
hazardous radiation exposure.
ATTENTION
L’utillisation de commandes, réglages ou procédures
autres que ceux spécifiés peut entraîner une dangereuse
exposition aux radiations.
ADVARSEL
Usynlig laserståling ved åbning, når sikkerhedsafbrydereer
ude af funktion. Undgå udsættelse for stråling.
This Compact Disc player is classified as a CLASS 1
LASER product.
The CLASS 1 LASER PRODUCT label is located on the
rear exterior.
CLASS 1LASER PRODUCT
KLASSE 1LASER PRODUKT
LUOKAN 1LASER LAITE
KLASS 1LASER APPARAT
Precaution to replace Optical block
(KSS-213F)
Body or clothes electrostatic potential could
ruin laser diode in the optical block. Be sure
ground body and workbench, and use care the
clothes do not touch the diode.
1) After the connection, remove solder shown in
right figure.
Rated: 65 W + 65 W (1 kHz,
T.H.D.1%, 6 ohms/DIN 45500)
Reference: 80 W + 80 W (1 kHz,
T.H.D.10%, 6 ohms/DIN 45324)
EZ:
DIN MUSIC POWER: 140 W + 140 W
Rear (Surround)
Rated: 20 W + 20 W (1 kHz,
T.H.D.1%, 8 ohms/DIN 45500)
Reference: 25 W + 25 W (1 kHz,
T.H.D.10%, 8 ohms/DIN 45324)
EZ:
DIN MUSIC POWER: 47 W + 47 W
Centre
Rated: 20 W (1 kHz, T.H.D.1%,
8 ohms/DIN 45500)
Reference: 25 W (1 kHz, T.H.D.10%,
8 ohms/DIN 45324)
EZ:
DIN MUSIC POWER: 47 W
Total harmonic distortion0.1 % (8 W, 1 kHz, 6 ohms,
DIN AUDIO/Front)
InputsVIDEO/AUX: 310 mV (adjustable)
MD: 310 mV (adjustable)
MIC 1, MIC 2: 1.2 mV (10 kohms)
Outputs5.1 CH INPUT
FRONT (L,R): 400 mV
REAR (L,R): 400 mV
CENTER: 700 mV
SUB WOOFER: 400 mV
LINE OUT: 175 mV
SUB WOOFER: 1 V
SPEAKERS: accept speakers of
6 ohms or more
SURROUND SPEAKERS:
accept speakers of 8 ohms to 16 ohms
CENTER SPEAKER: accept speakers
of 8 ohms or more
PHONES (stereo jack): accepts
headphones of 32 ohms or more
<General>
Power requirements230 V AC, 50 Hz
Power consumption160 W
Power consumption inIf the power-economizing mode is
standby modeECO OFF: 30 W
If the power-economizing mode is
ECO ON or ECO AUTO: 0.9 W
Dimensions of main unit284 x 122 x 337 mm
(W x H x D)
Weight of main unit6.9 kg
<CD PLAYER DX-NH2000>
LaserSemiconductor laser (λ =780 nm)
D-A converter1 bit dual
Signal-to-noise ratio85 dB (1 kHz, 0 dB)
Harmonic distortion0.05 % (1 kHz, 0 dB)
Wow and flutterUnmeasurable
Dimensions of main unit284 x 101 x 315 mm
(W x H x D)
Weight of main unit2.3 kg
<CASSETTE DECK FX-NH2000>
Track format4 tracks, 2 channels stereo
Frequency responseType II (high/CrO2) tape:
50 Hz – 16000 Hz
Type I (normal) tape:
50 Hz – 15000 Hz
Signal-to-noise ratio60 dB (Dolby B NR ON, Type IItape
peak level)
Recording systemAC bias, AC erase
HeadsDeck 1: Playback head x 1
Deck 2: Recording/playback
head x 1,erase head x 1
Dimensions of main unit284 x 122 x 315 mm
(W x H x D)
Weight of main unit2.0 kg
<GRAPHIC EQUALIZER GE-NDPH2100>
Dimensions of main unit284 x 101 x 328 mm
(W x H x D)
Weight1.8 kg
<SPEAKER SYSTEM SX–NDPH2100>
Cabinet type3 way (magnetic shielded type)
SpeakersWoofer:
140 mm cone type x 2
Tweeter:
60 mm cone type
Super tweeter:
20 mm ceramic type
Impedance6 ohms
Output sound pressure level 88 dB/W/m
Dimensions (W x H x D)250 x 443 x 250 mm
Weight7.0 kg
• Design and specifications are subject to change without
notice.
• Manufactured under license from Dolby Laboratories Licensing
Corporation.
“DOLBY” and the double-D symbol are trademarks of Dolby
Laboratories Licensing Corporation.
• The word “BBE” and the “BBE symbol” are trademarks of BBE
Sound, Inc.
Under license from BBE Sound, Inc.
– 3 –
Page 4
ACCESSORIES / PACKAGE LIST
PART NO.
NO.
1 8A-SPM-905-010 IB,K(E)M<K>
1 8A-SPM-906-010 IB,EZ(9L)M<EZ>
2 8Z-NFV-702-010 RC UNIT,ZAS05
3 87-006-225-010 AM LOOP ANT NC2
4 87-A90-118-010 ANT,WIRE FM (Z)
C602 87-010-401-080 CAP, ELECT 1-50V
C603 87-010-182-080 C-CAP,S 2200P-50 B
C604 87-010-182-080 C-CAP,S 2200P-50 B
C605 87-010-369-080 C-CAP,S 0.033-25 K B
C606 87-010-369-080 C-CAP,S 0.033-25 K B
C702 87-010-402-080 CAP, ELECT 2.2-50V
C703 87-016-669-080 C-CAP,S 0.1-25 K B
C704 87-016-669-080 C-CAP,S 0.1-25 K B
C705 87-016-460-080 C-CAP,S 0.22-16 B
C706 87-016-460-080 C-CAP,S 0.22-16 B
C908 87-010-190-080 S CHIP F 0.01
C909 87-012-368-080 C-CAP,S 0.1-50 F
C910 87-012-368-080 C-CAP,S 0.1-50 F
C911 87-012-141-080 CHIP-CAPACITOR,0.22-16F
C912 87-010-196-080 C-CAP,S 0.1-25 F
C913 87-010-196-080 CHIP CAPACITOR,0.1-25
C914 87-010-190-080 C-CAP,S 0.01-50 F
C915 87-010-190-080 C-CAP,S 0.01-50 F
C916 87-010-190-080 C-CAP,S 0.01-50 F
C917 87-010-190-080 C-CAP,S 0.01-50 F
C302 87-010-404-040 CAP,E 4.7-50 SME
C340 87-010-175-080 CAP 560P
C341 87-010-175-080 CAP 560P
C342 87-010-175-080 CAP 560P
C343 87-010-175-080 CAP 560P
C344 87-010-175-080 CAP 560P
C345 87-010-175-080 CAP 560P
C346 87-010-175-080 CAP 560P
C347 87-010-175-080 CAP 560P
C348 87-010-175-080 CAP 560P
C838 87-012-349-080 C-CAP,S 1000P-50 CH
C839 87-015-695-080 CAP, ELECT 1-50V
C840 87-015-695-080 CAP, ELECT 1-50V
C841 87-A10-799-080 C-CAP,S 5600P-16 J B CM
C842 87-A10-802-080 C-CAP,S 0.047-16 J B CM
C843 87-A10-229-080 C-CAP,S 0.68-10 K W5
C844 87-012-393-080 C-CAP,S 0.22-16 R K
C845 87-012-393-080 C-CAP,S 0.22-16 R K
C846 87-015-688-080 CAP, ELECT 4.7-35V
C847 87-015-688-080 CAP, ELECT 4.7-35V
C848 87-012-393-080 C-CAP,S 0.22-16 R K
C849 87-012-393-080 C-CAP,S 0.22-16 R K
C850 87-016-081-080 C-CAP,S 0.1-16 RK
C851 87-A10-802-080 C-CAP,S 0.047-16 J B CM
C852 87-A10-802-080 C-CAP,S 0.047-16 J B CM
C853 87-016-081-080 C-CAP,S 0.1-16 RK
C854 87-016-081-080 C-CAP,S 0.1-16 RK
C855 87-A10-801-080 C-CAP,S 0.022-16 J B CM
C856 87-A10-801-080 C-CAP,S 0.022-16 J B CM
C857 87-016-081-080 C-CAP,S 0.1-16 RK
WIRING - 4 (AC1 / SUB TRANS / AC2 / ECO : MX-NDPH2100)
123456789101112131415
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
– 17 –
R
S
T
U
Page 18
SCHEMATIC DIAGRAM – 4 (AC1 / SUB TRANS / AC2 : MX-NDPH2100 )
– 18 –
Page 19
WIRING - 5 (PRO LOGIC : MX-NDPH2100)
123456789101112131415
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
– 19 –
R
S
T
U
Page 20
SCHEMATIC DIAGRAM – 5 (PRO LOGIC : MX-NDPH2100 )
– 20 –
Page 21
FL GRID (10-BT-218GNK) ASSIGNMENT AND ANODE CONNECTION (MX-NDPH2100)
GRID ASSIGNMENTANODE CONNECTION
– 21 –
Page 22
IC BLOCK DIAGRAM (MX-NDPH2100)
IC, NJM2152M
– 22 –
Page 23
– 23 –
Page 24
IC DESCRIPTION (MX-NDPH2100)
IC, UPD780228GF-065-3BA
Pin No.
1K-SCANOKey scan output.
2RHYTHM-CSOChip select output to IC, BU9990-03FS. (Not used)
3RHYTHM-SCLKOClock output to IC, BU9990-03FS. (Not used0
4RHYTHM-SDOData output to IC, BU9990-03FS. (Not used)
5PLL CEOPLL IC chip enable output.
6O-M/CLKOMain clock output.
7O-M/DATAOMain data output.
8O-M/STBOMain strobe output.
9I/O-SERIALI/OCommunication port for GEQ, CD and DECK.
10O-MUTEOSystem mute (ON when "H").
11O-POWEROSystem power supply (ON when "L").
12DIMER 2ODimmer control ("L" when 2).
13O-MUTE SOSound L, R, Center, SW Mute.
14LED-ECOOECO LED output.
15NC–Not connected.
16NC–Not connected.
17IC–Connect to GND.
Pin NameI/O
Description
18VSS–GND.
19VDD–Power supply terminal.
20LED-MDOMD LED output.
21
22TUNE/IFOITuning detection input.
23STEREOIStereo detection input.
24NC–Not connected.
25I-RE VOL A
26I-RE VOL B
27LED-CDOCD LED output.
28NC–Not connected.
29RDS-CLKITUNER RDS IC clock input.
30RESETIReset input.
31I-RDSITuner RDS input.
32GEQ-REQOLatch output to IC, M62449FP.
33COUNTERITape counter input.
34I-RMCIRemote controller input (Active "L").
35I-SURR-OFFIStop surround function when using head phone.
TM-BASEITime base input.
IRotary Encoder Input A / B.
36O-SHIFTOOutput for oscillated frequency shift.
37VDD–Power supply terminal.
38X2
39X1
40VSS–GND.
41AVDD–Power supply terminal.
42HOLDIPower failure / over current detected input.
–4.19MHz oscillator circuit.
– 24 –
Page 25
Pin No.
43I-RDS-SIGITuner tuning signal level A/D input.
44I-MICIMIC input level detection.
45KEY1IKEY1 input.
46KEY2IKEY2 input.
47I-TEMPOITEMPO input (100Hz, 3.3kHz).
48I-GE-2IDEMO, TIMER, CLOCK, SPICE A, AUTO SPICE / FILL IN input.
49I-GE-1IJOG, SPICE B SW input.
50AVSS–GND.
51LED-TAPEOTape LED output.
52LED-TUNEROTuner LED output.
53LED-VIDEOOVideo LED output.
25 87-A80-157-010 AC CORD ASSY, E BLK CC
26 87-085-185-010 BUSHING, AC CORD (E)CM-22B
27 87-085-213-010 FOOT,H12.5
28 8Z-NB8-240-010 COVER, PL
29 88-SPM-208-010 HLDR,PWB PRO
A 87-067-703-010 BVT2+3-10 W/O SLOT
B 87-067-758-010 BVT2+3-12 W/O SLOT
C 87-067-688-010 BVTT+3-6
D 87-721-095-410 QT2+3-8GLD W/O SLOT
E 87-067-822-010 BVT2+3-20 W/O SLOT
F 87-067-579-010 BVT2+3-8 W/O SLOT
G 87-591-094-410 QIT+3-6
H 87-078-191-010 S-SCREW,IT+4-10 SW CH
I 87-B10-091-010 UTT2+3-10 W/O SLOT BLK
NO.
DESCRIPTIONREF. NO.KANRI
COLOR NAME TABLE
Basic color symbolColorBasic color symbolColorBasic color symbolColor
BBlackCCreamDOrange
GGreenHGrayLBlue
LTTransparent BlueNGoldPPink
RRedSSilverSTTitan Silver
TBrownVVioletWWhite
WTTransparent WhiteYYellowYTTransparent Yellow
LMMetallic BlueLLLight BlueGTTransparent Green
LDDark BlueDTTransparent OrangeGMMetallic Green
LED208 87-A40-380-080 LED,SEL6510C-TP5 GRN
LED209 87-A40-317-080 LED,SLR-342VCT31 RED
LED210 87-A40-317-080 LED,SLR-342VCT31 RED
LED211 87-A40-317-080 LED,SLR-342VCT31 RED
LED212 87-A40-317-080 LED,SLR-342VCT31 RED
LED213 87-A40-317-080 LED,SLR-342VCT31 RED
LED214 87-A40-317-080 LED,SLR-342VCT31 RED
LED215 87-A40-317-080 LED,SLR-342VCT31 RED
LED216 87-A40-317-080 LED,SLR-342VCT31 RED
S301 87-A90-095-080 SW,TACT EVQ11G04M
FL GRID ASSIGNMENT AND ANODE CONNECTION (GE-NDPH2100)
GRID ASSIGNMENTANODE CONNECTION
33
Page 34
IC BLOCK DIAGRAM (GE-NDPH2100)
– 34 –
Page 35
IC DESCRIPTION (GE-NDPH2100)
IC, LC866448W
Pin No. Pin Name I/O Description
1O-C.SHIFTOMicro computer clock shift output.
2PRO LOGICOPRO LOGIC LED output.
33-STEREOO3 STEREO LED output.
4PHANTOMOPHANTOM LED output.
5NORMALONORMAL LED output.
6NC–Not connected.
7 RESETIReset input.
8 NC–Connected to GND.
9NC–Connected to GND.
10VSS1–GND.
11CF1–
12CF2–
13VDD1–Power supply.
14 I-HOLD I
Connected to crystal oscillator (5.76MHz).
System power supply monitor AD input.’H’:Normal operation.’L’:to stop
clock and main memory.
15I-KEY1IKEY 1 AD input.
16NC–Connected to GND.
17I-SPEANAISpectrum analyzer level AD input.
18NC–Connected to GND.
19I-JOGIJog rotary encoder input.
20~23NC–Connected to GND.
24PRO LOGICIInput prologic switch “H” when prologic ,”L” when not prologic.
41VDD2–Connected to GND.
42VP–Power FL display negative supply terminal.
43~63S8~S28OFL Segment S8~S28 output.
64NC–Not used.
65LED ONOMULTI JOG LED output.
66LED ONOMULTI JOG LED output.
67~69,72NC–Not connected.
70O-L FREQ ONOSpectrum analyzer low frequency output.
71O-H FREQ ONOSpectrum analyzer high frequency output.
73VSS2–GND.
74SPEANA COSpectrum analyzer band switch output C.
75SPEANA BOSpectrum analyzer band switch output B.
76SPEANA AOSpectrum analyzer band switch output A.
77SELOSpectrum analyzer band switch output select .
78~79NC–Not connected.
80I/O-SERIALI/OInput/output serial data for communication.