Aiwa XP-V312 AEZ1, XP-V312 AK1, XP-V311 AHAB, XP-V311 AEZ1, XP-V311 AHRJ1 Service Manual

XP-V310

Y1B(LL) Y1B(S) Y1(S)
Y1B(D) Y1B(LT)

AHRJ1(S) AHRJ1(D)

XP-V311
XP-V312

AEZ1(L) AHAB(S)
AEZ1(S)

AK1(S) AEZ1(S)

SERVICE MANUAL

COMPACT DISC PLAYER

This Service Manual is the "Revision Publishing" and replaces "Simple Manual"
(S/M Code No. 09-003-339-8T2).

BASIC CD MECHANISM : DA23L

S/M Code No. 09-003-339-8R2

REVISION

DATA

PROTECTION OF EYES FROM LASER BEAM DURING SERVICING

This set employs laser. Therefore, be sure to follow carefully the
instructions below when servicing.

WARNING!

WHEN SERVICING, DO NOT APPROACH THE LASER EXIT
WITH THE EYE TOO CLOSELY. IN CASE IT IS NECESSARY TO
CONFIRM LASER BEAM EMISSION. BE SURE TO OBSERVE
FROM A DISTANCE OF MORE THAN 30cm FROM THE
SURFACE OF THE OBJECTIVE LENS ON THE OPTICAL
PICK-UP BLOCK.

Caution: Invisible laser radiation when
open and interlocks defeated avoid expo­sure to beam.
Advarsel:Usynling laserståling ved åbning,
når sikkerhedsafbrydere er ude af funktion.
Undgå udsættelse for stråling.

VAROITUS!

Laiteen Käyttäminen muulla kuin tässä käyttöohjeessa mainit­ulla tavalla saattaa altistaa käyt-täjän turvallisuusluokan 1 ylit­tävälle näkymättömälle lasersäteilylle.

VARNING!

Om apparaten används på annat sätt än vad som specificeras i
denna bruksanvising, kan användaren utsättas för osynling
laserstrålning, som överskrider gränsen för laserklass 1.

CAUTION

Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous
radiation exposure.

ATTENTION

L'utilisation de commandes, réglages ou procédures autres que
ceux spécifiés peut entraîner une dangereuse exposition aux
radiations.

ADVARSEL!

Usynlig laserståling ved åbning, når sikkerhedsafbrydereer ude
af funktion. Undgå udsættelse for stråling.

This Compact Disc player is classified as a CLASS 1 LASER
product.
The CLASS 1 LASER PRODUCT label is located on the rear
exterior.

CLASS 1
KLASSE 1
LUOKAN 1
KLASS 1

LASER PRODUCT
LASER PRODUKT
LASER LAITE
LASER APPARAT

Precaution to replace Optical block
(SF-P200)

Body or clothes electrostatic potential could ruin
laser diode in the optical block. Be sure ground
body and workbench, and use care the clothes
do not touch the diode.

1) After the connection, remove solder shown in
the right figure.

:SOLDER

10 9

PICK UP ASSY

116

SF-P200

2

SPECIFICATIONS

Design and specifications are subject to change without notice.

•

3

ELECTRICAL MAIN PARTS LIST

REF. NO PART NO. KANRI DESCRIPTION

IC
87-A21-448-040 C-IC,BH6554FV

87-A21-083-040 C-IC,BH6508FS
87-A21-381-040 C-IC,LA9235M
87-A21-591-010 C-IC,LC78641NE-D
87-A21-085-040 C-IC,TA2120FN

8A-HC7-607-010 C-IC,UPD789406AGC-014-8BT

TRANSISTOR
89-211-323-080 C-TR,2SB1132R

87-A30-332-040 C-TR,CPH3106
87-A30-278-040 C-FET,2SK2980
87-A30-287-040 C-TR,DTC114TKA
87-A30-246-040 C-TR,2SA1037AK

86-NFZ-667-040 C-TR,DTC123JKA
89-416-643-080 C-TR,2SD1664R
89-324-123-080 C-TR,2SC2412K S

DIODE
87-A40-592-040 C-ZENER,HZM11NB2

87-A40-590-040 C-DIODE,HRW0202A
87-A40-554-040 C-DIODE,RB491D
87-A40-469-080 C-DIODE,HSM2838CTR
87-A40-836-040 C-ZENER,HZM6.2NB1

MAIN C.B
C101 87-010-553-040 CAP,E 47-16 GAS

C102 87-010-551-040 CAP,E 33-10 GAS
C103 87-A10-505-040 CAP,E 220-6.3 105 SF
C104 87-010-503-040 CAP,E 220-4 GAS
C105 87-010-498-040 CAP,E 10-16 GAS

C106 87-010-502-040 CAP ELECT GAS 100/4
C107 87-010-196-080 CHIP CAPACITOR,0.1-25
C108 87-012-145-080 CAP, CHIP S 270P CH
C109 87-010-198-080 CAP, CHIP 0.022
C110 87-A10-826-080 C-CAP,S 1-10 K B

C111 87-010-196-080 CHIP CAPACITOR,0.1-25
C112 87-010-196-080 CHIP CAPACITOR,0.1-25
C113 87-A10-826-080 C-CAP,S 1-10 K B
C115 87-010-196-080 CHIP CAPACITOR,0.1-25
C116 87-010-196-080 CHIP CAPACITOR,0.1-25

C117 87-010-196-080 CHIP CAPACITOR,0.1-25
C201 87-A10-505-040 CAP,E 220-6.3 105 SF
C202 87-010-175-080 CAP 560P
C204 87-010-213-080 C-CAP,S 0.015-50 B
C205 87-010-213-080 C-CAP,S 0.015-50 B

C206 87-A10-826-080 C-CAP,S 1-10 K B
C207 87-A10-826-080 C-CAP,S 1-10 K B
C208 87-010-177-080 C-CAP,S 820P-50 SL
C209 87-010-213-080 C-CAP,S 0.015-50 B
C210 87-010-213-080 C-CAP,S 0.015-50 B

C212 87-A10-826-080 C-CAP,S 1-10 K B
C301 87-016-557-040 CAP,E 100-6.3 SF
C302 87-010-502-040 CAP ELECT GAS 100/4
C303 87-016-557-040 CAP,E 100-6.3 SF
C304 87-010-502-040 CAP ELECT GAS 100/4

C305 87-010-501-040 E/CAP GAS 47-4
C306 87-010-196-080 CHIP CAPACITOR,0.1-25
C308 87-010-196-080 CHIP CAPACITOR,0.1-25
C309 87-010-178-080 CHIP CAP 1000P
C311 87-010-318-080 C-CAP,S 47P-50 CH

C313 87-A10-826-080 C-CAP,S 1-10 K B
C314 87-A10-201-080 C-CAP,S0.33-16 KB
C351 87-016-557-040 CAP,E 100-6.3 SF
C352 87-010-503-040 CAP,E 220-4 GAS
C353 87-A10-826-080 C-CAP,S 1-10 K B

NO.

REF. NO PART NO. KANRI DESCRIPTION

C354 87-010-196-080 CHIP CAPACITOR,0.1-25
C355 87-010-312-080 C-CAP,S 15P-50 CH
C356 87-010-312-080 C-CAP,S 15P-50 CH
C357 87-010-196-080 CHIP CAPACITOR,0.1-25
C358 87-010-322-080 C-CAP,S 100P-50 CH

C359 87-A10-369-080 C-CAP,S 0.47-16 K B
C360 87-016-669-080 C-CAP,S 0.1-25 K B
C361 87-010-322-080 C-CAP,S 100P-50 CH
C362 87-016-669-080 C-CAP,S 0.1-25 K B
C363 87-010-197-080 CAP, CHIP 0.01 DM

C364 87-016-369-080 C-CAP,S 0.033-25 B K
C365 87-010-322-080 C-CAP,S 100P-50 CH
C367 87-010-175-080 CAP 560P
C368 87-010-196-080 CHIP CAPACITOR,0.1-25
C701 87-010-501-040 E/CAP GAS 47-4

C702 87-010-495-040 CAP,E 2.2-50 GAS
C703 87-010-498-040 CAP,E 10-16 GAS
C704 87-010-503-040 CAP,E 220-4 GAS
C705 87-010-503-040 CAP,E 220-4 GAS
C706 87-010-498-040 CAP,E 10-16 GAS

C707 87-010-501-040 E/CAP GAS 47-4
C708 87-A10-826-080 C-CAP,S 1-10 K B
C709 87-A10-826-080 C-CAP,S 1-10 K B
C710 87-012-155-080 C-CAP 180P-50CH
C711 87-012-155-080 C-CAP 180P-50CH

C712 87-012-141-080 CHIP-CAPACITOR,0.22-16F
C713 87-010-196-080 CHIP CAPACITOR,0.1-25
C714 87-010-196-080 CHIP CAPACITOR,0.1-25
C715 87-010-196-080 CHIP CAPACITOR,0.1-25
C716 87-010-196-080 CHIP CAPACITOR,0.1-25

C717 87-010-196-080 CHIP CAPACITOR,0.1-25
C801 87-010-501-040 E/CAP GAS 47-4
C802 87-010-196-080 CHIP CAPACITOR,0.1-25
C803 87-010-196-080 CHIP CAPACITOR,0.1-25
C804 87-010-178-080 CHIP CAP 1000P

C805 87-010-322-080 C-CAP,S 100P-50 CH
C806 87-010-319-080 C-CAP,S 56P-50 CH
C807 87-010-319-080 C-CAP,S 56P-50 CH
C808 87-010-196-080 CHIP CAPACITOR,0.1-25
CN201 87-A61-104-010 CONN,16P H WHITE 52089-1610

CN202 87-009-411-010 CONN,6P ZH V
FB701 87-A50-623-080 C-COIL,BK2125HS102
FB702 87-A50-623-080 C-COIL,BK2125HS102
FB703 87-A50-623-080 C-COIL,BK2125HS102
FB704 87-A50-623-080 C-COIL,BK2125HS102

J101 87-A60-421-010 JACK,DC HEC3600 BLK 6
J701 85-HC5-616-010 JACK,3.5 ST W/R GRN
L101 87-A50-574-010 COIL,100UH #7607
L102 87-A50-573-010 COIL,330UH LHL06NB
L301 87-A50-455-080 C-COIL,47UH-FSLB2520

L302 87-A50-501-080 C-COIL,10UH-FSLB2520
L351 87-A50-501-080 C-COIL,10UH-FSLB2520
L801 87-A50-501-080 C-COIL,10UH-FSLB2520
L802 87-A50-455-080 C-COIL,47UH-FSLB2520
LCD101 8A-HC7-602-010 LCD,AHC-7

R105 87-022-355-080 C-RES,S10K-1/10W F
R107 87-022-358-080 C-RES,S 18K-1/10W F
R307 87-022-202-080 C-RES,S33K 1/10WF
R308 87-022-202-080 C-RES,S33K 1/10WF
R309 87-022-202-080 C-RES,S33K 1/10WF

R310 87-022-202-080 C-RES,S33K 1/10WF
R311 87-022-364-080 C-RES,S 82K-1/10W F
R312 87-022-364-080 C-RES,S 82K-1/10W F
S101 87-A90-095-080 SW,TACT EVQ11G04M
S102 87-A90-095-080 SW,TACT EVQ11G04M

S103 87-A90-095-080 SW,TACT EVQ11G04M
S104 87-A90-095-080 SW,TACT EVQ11G04M
S105 87-A90-095-080 SW,TACT EVQ11G04M
S106 87-A90-095-080 SW,TACT EVQ11G04M
S801 87-A91-622-010 SW,MICRO PV1102

NO.

4

REF. NO PART NO. KANRI DESCRIPTION

S802 87-A91-742-010 SW,SL 4-1-3 HSW2061-010010
VR701 87-A90-462-010 VR,RTRY 30KCX2 H RK14J12A0
X351 87-A70-202-080 C-VIB,CER 16.93MHZ CSACV-MXJ04

• Regarding connectors, they are not stocked as they are not the initial order items.
The connectors are available after they are supplied from connector manufacturers upon the order is received.

NO.

CHIP RESISTOR PART CODE

Chip Resistor Part Coding

88

A

Resistor Code

Chip resistor

Wattage Type Tolerance
1/16W 1005 5% CJ

1/16W
1/10W

1/8W

1608
2125

3216

5%
5%

5%

TRANSISTOR ILLUSTRATION

C

Symbol

CJ
CJ

CJ

Figure

Value of resistor

Form

L

Dimensions (mm)

t

W

0.55

Resistor Code

108
118

128

LW t

1.0 0.5 0.35 104

1.6 0.8 0.45
2 1.25 0.45

3.2

1.6

: A
: A

B

E

2SA1037
2SC2412
2SK2980
CPH3106
DTC114TK
DTC123JK

BCE

2SB1132
2SD1664

5

LCD DISPLAY

6

SCHEMATIC DIAGRAM

C710
180p

C711
180p

OTHER MODELS

411AHRJ/

411AHA

8BT

87

WIRING

A

B

1

234567

8

9

10

11 12 13

14

C

D

E

F

SF-P200

G

H

I

J

K

109

TEST MODE

IC101

IC351

IC701

IC201

IC801

IC301

27

Q305

RF

31

VC

TEST MODE SHORT LAND

11

The servo circuit of this model has been designed to be free of adjustments and controlled within the IC. Therefore, adjustments and disk
judgement are performed automatically every time the TOC is read out. The adjustment status of each servo inside the IC can be
monitored in this test mode.

1. Startup procedure

1) Short the test land.

2) Insert the AC plug.

3) Press the STOP button. (The test mode starts.)
Note 1) The test mode is canceled by disconnecting the AC plug.
Note 2) The OPEN/CLOSE switch cannot be operated during the test mode.

2. Checking the RF level

Test point: RF & VC (Vref)
Test disk: TCD-782
Play back the disk and confirm that the RF waveform is in the following state:

0.8Vp-p or more

VOLT/DIV:200mV
TIME/DIV:0.5us

3. Checking each servo

The adjustment values of each servo can be checked by pressing the MODE button repeatedly during playback. The switching
procedure is as follows.
Check mode OFF™Vref offset (RO)™focus offset (FO)™tracking offset (TO)™tracking balance (TB)™tracking gain (TG) ™
focus gain (FG)™focus bias (FB)™check mode OFF

Example: Tracking offset (TO) Adjustment value™F5

RNDM RESUME

1

DSL

Tracking offset

* Adjustment values are indicated in hexadecimal.
When displaying each mode on the LCD and pressing the PLAY button in the STOP status, the center value is displayed on the LCD.
After the disk starts rotating, the adjustment value that was set during automatic adjustment is displayed. The display range of the
center values and adjustment values of each mode are as follows. There are 256 steps for displaying the values of all modes.

Center value

1) Vref offset (RO)

2) Focus offset (FO)

3) Tracking offset (TO)

4) Tracking balance (TB)

5) Tracking gain (TG)

6) Focus gain (FG)

7) Focus bias (FB)

Adjustment value

Center value

00
00
00
80
40
40
00

Display range

80-7F
80-7F
80-7F
00-FF
00-FF
00-FF
80-7F

12

4. Amount of change of jitter

The amount of change of jitter is displayed in the focus bias check mode. The displayed value has 256 steps from 00 to FF.

Example: focus bias (FB) Adjustment value™00 Jitter value™FD

RNDM RESUME

1

DSL

Tracking offset Adjustment value

* Adjustment values and jitter values are indicated in hexadecimal.

Jitter value

13

WAVE FORM

1 IC301 Pin ≥ VOLT/DIV: 0.2V

RF TIME/DIV: 0.5µS

2 IC301 Pin * VOLT/DIV: 0.2V

TE TIME/DIV: 50µS

3 IC301 Pin ¡ VOLT/DIV: 0.1V

FE- TIME/DIV: 2mS

7 IC601 Pin ∞ VOLT/DIV: 0.1V

SPDO TIME/DIV: 5mS

4 IC351 Pin VOLT/DIV: 1V

XOUT TIME/DIV: 50mS

5 IC801 Pin VOLT/DIV: 1V

X1 TIME/DIV: 0.2µS

6 IC351 Pin VOLT/DIV: 2V

LRSY TIME/DIV: 5µS

52

f=16.93MHz

69

f=4.2MHz

57

f=44.1kHz

14

IC BLOCK DIAGRAM
IC, BH6508FS

IC, BH6554FV

IC, TA2120FN

15

IC DESCRIPTION
IC, LC78641NE-D

Pin No. Pin Name I/O Description

1

PDO1

Internal VCD control phase comparator output pin.

O

10
11
12
13
14
15
16
17

—

—

Internal VCD control phase comparator output pin. OFF for rough servo, ON for phase

O

servo.
Internal VCD ground pin.
PDO output current adjustment resistor connection pin. (pull up)

I

Internal VCD power supply pin. (2000pF or more path controller to be inserted at a
point nearer to the pin between this pin and GND)
VCD frequency range adjustment resistor connection pin. (pull up)

I

Mirror detection signal input pin.

I

SLCO output current adjustment resistor connection pin. (pull up)

I

Control outout.

O

EFM signal input pin.

I

Jitter detection monitor pin.

O

Jitter detection adjustment pin.

O

BH signal input pin. A/D input. (Must be connected to OV when unused)

I

PH signal or RFENV signal input pin. A/D input.

I

FE signal input pin. A/D input.

I

TE signal input pin. A/D input.

I

VREF input pin. A/D input.

I

2

3
4

5

6
7
8
9

PDO2

VVSS

PCKIST

VVDD

FR

HFL

SLCIST

SLCO

EFMIN

JITTV
JITTC

BH

PH (RFENV)

FE
TE

VREF

18

19
20
21
22
23
24
25
26

27

28
29
30
31
32
33

ADAVDD

ADAVSS

PHREF
BHREF

TBLO

TDO

FDO
SPDO
SLDO

DVREF/FG

LASER
CONT1
CONT2
CONT3
CONT4
CONT5

—

—

O
O
O
O
O
O
O

I/O

O
I/O
I/O
I/O
I/O
I/O

Servo A/D, D/A power supply pin. (2000pF or more path controller to be inserted at a
point nearer to the pin between this pin and GND)
Servo A/D, D/A ground pin.
PH reference output pin. D/A output.
BH reference output pin. D/A output.
Tracking balance output pin. D/A output.
Tracking control output pin. D/A output.
Focus control output pin. D/A output.
Spindle control output pin. D/A output.
Thread control output pin. D/A output.
Output driver VREF output pin. Input FG signal input pin. (Must be connected to OV
when unused)
Laser ON/OFF control pin.
General-purpose input/output pin 1.
General-purpose input/output pin 2.
General-purpose input/output pin 3.
General-purpose input/output pin 4.

General-purpose input/output pin 5.
34
35

36

PCK

C2F

VDD

—

EFM data playback clock monitor pin. Average 4.3218MHz when the phase is locked.

O

C2 flag output pin.

O

Digital power supply pin. (2000pF or more path controller to be inserted at a point

nearer to the pin between this pin and GND)

16

Pin No. Pin Name I/O Description

37

DOUT

Digital OUT output pin. (EIAJ format)

O
38
39
40

41

42
43

44

45
46
47
48

49

50

51
52

FSX
EFLG
TEST

EMPH

MUTEL

MUTER

LVDD

LCHO

LVSS
RVSS

RCHO

RVDD

XVDD

XIN

XOUT

O
O

I/O

O
O

—

O
—
—

O

—

—

O

Output pin for the 7.35kHz synchronization signal divided from the crystal osillator.

C1 C2 error correction monitor pin. Test input pin. Must be connected to OV.

I

Emphasis pin. Which becomes an input pin after reset and can becontrolled externally.
This becomes an emphasis monitor pin under control by command.
L channnel mute output pin.
R channel mute output pin.
L channel power supply pin. (2000pF or more path controller to be inserted at a point
nearer to the pin between this pin and GND)
L channel output pin.
L channel ground pin, Must be connected to 0V.
R channel ground pin, Must be connected to 0V.
R channel output pin.
R channel power supply pin. (2000pF or more path controller to be inserted at a point
nearer to the pin between this pin and GND)
Crystal oscillator power supply pin. (2000pF or more path controller to be inserted at a
point nearer to the pin between this pin and GND)

I

Connections for a 16.9344MHz crystal oscillator pin.

53
54
55
56
57
58
59
60

61

62
63
64
65
66
67
68

XVSS

ASLRCK

ASDACK

ASDFIN

LRSY

DATACK

DATA

16M

SFSY

SBSY

PW

SBCK

CE
CL

DI

DO

Crystal oscillator ground pin. Must be connected to 0V.

—

L/R clock input pin. (Must be connected to 0V when unused)

I

Bit clock input pin. (Must be connected to 0V when unused)

I

L/R channel data input pin. (Must be connected to 0V when unused)

I

L/R clock output pin.

O

Bit clock output pin.

O

L/R channel data output pin.

O

16.9344MHz output pin.

O

Subcode frame synchronization signal output pin. This signal falls when the subcode is

O

in the standby state.
Subcode clock synchronization signal output pin.

O

Subcode P, Q, R, S, T, U and W output pin.

O

Subcode readout clock input pin.

I

Chip enable signal input pin.

I

Data transfer clock input pin.

I

Data input pin.

I

Data output pin.

O

69
70
71
72

*INT

*WRQ

*RES

DRF

Interruption signal output pin.

O

Interruption signal output pin.

O

Reset input pin. This pin must be set low briefly after power is first applied.

I

Focus ON detect pin.

O

17

Pin No. Pin Name I/O Description

73

VDD5V

—

Microprocessor interface power supply. (2000pF or more path controller to be inserted

at a point nearer to the pin between this pin and GND)
74
75
76

77

78

79

80

VSS
CONT6
CONT7

V/*P

FSEQ

DEFECT

EFMO

—
I/O
I/O

O

O

I/O

O

Digital ground pin. Must be connected to 0V.
General-purpose input/output pin 6.
General-pirpose input/output pin 7.
Rough servo/phase control automatic switching monitor output pin. “H” for rough
servo and “L” for phase servo.
Synchronization signal detection output pin. Outputs a high level when the
synchronization signal detected from the EFM signal and the internally generated
synchronization signal agree.
Defect pin. Which becomes an input pin after reset and can be controlled externally.
This becomes the defect monitor pin under control by command.
EFM signal output pin.

18

IC, µPD789405AGC-014-8BT

IC, LA9253M

Pin No. Pin Name I/O Description

1
2

3-5

6

7-10

11-38

39
40

41-47

48

49-52

VDO1

BIAS

VLC0-VLC2

VSS1

COM0-COM3

S0-S27

AVDD

AVREF

ANI6-0

AVSS

INTP3-INTP0

—
—
—
—

—
—

—

Positive polarity power supply (except for port section).
Feeding the LCD drive power supply voltage.
LCD drive power supply voltage.
Ground potential (except for port section).
Common signal output from LCD controller/driver.

O

Segment signal output from LCD controller/driver.

O

A/D comparator analog power supply.
A/D comparator reference voltage.
Analog input signal to A/D comparator.

I

A/D comparator ground potential.
External interrupt input whose effective edge (rise-up or fall-down or both edges of

I

rise-up and fall-down) can be specified.
53
54
55
56

TO2

SI

SO

________

SCK

I/O

Output signal from 8-bit timer (TM02).

O

Serial data input signal of serial interface.

I

Serial data output signal of serial interface

O

Serial clock input/output signal of serial interface

Port 5.

4-bit N-channel open-drain input/output port.

57-60

P53-P50

I/O

Input or output; can be specified in units of 1 bit.

When it is used as an input port, built-in pull-up resistor can be used as specified by

mask option.

Port0.

4-bit input/output port.

61-64

P03-P00

I/O

Input or output; can be specified in units of 1 bit.

When it is used as an input port, built-in pull-up resistor can be used as specified by

software

Port 4.

8-bit input/output port.

65, 66

P47, P46

I/O

Input or output; can be specified in units of 1 bit.

When it is used as an input port, built-in pull-up resistor can be used as specified by

software.

System reset input.

I

67

_____________

RESET

Pin No. Pin Name I/O Description

1
2
3
4
5
6
7
8

9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30

FIN1
FIN2
TIN1
TIN2

REF1

VREF

LDS
LDD
GND

LDOF
ODRV
AGON

EFBL

TESO

TESI

TES
HFL

TE

TE-

FE

FE-

RFEV

N/C

BH
PH

N/C

RF

RF-

RFSW

VCC

I
I

Pick-up signal input.

I
I

Pin designed for reference voltage.

I

Reference voltage output.

O

APC monitor voltage input.

I

APC output.

O

GND.

—

laser OFF pin (H: ON L: OFF).

I

Speed switch pin (H: double L: normal speed).

I

AGC ON pin (H: ON L: OFF).

I

FE balance adjustment pin.

I

TE signal output for TES.

O

TE input for TES formation.

I

TES output.

O

HFL signal output.

O

TE signal output.

O

Minus input for TE gain design.

I

FE signal output.

O

Minus input for FE gain design.

I

RF envelop signal output.

O

Pin N/C.

—

Capasitance connection pin for RF bottom clamp.

I

Capasitance connection pin for RF gain design.

I

Pin N/C.

—

RF signal output.

O

Minus input for RF signal gain design.

I

Switch for equalizer design when RF has double speed.

I

Power supply.

—

68
69
70
71
72
73
74

75-80

X2
X1

VSS0

VDD0

XT2
XT1

IC/VPP

P45-P40

—

—
—
—

—

Terminal to connect external crystal for main system clock oscillation.

I

Ground potential of port section.
Positive polarity power supply for port section.

Terminal to connect external crystal for sub system clock oscillation.

I

This pin is internally connected. Connect this pin directly to Vss0 or Vss1.
Key-return signal detection input signal.

I

2019

MECHANICAL EXPLODED VIEW 1/1

8

MECHANICAL PARTS LIST 1/1

LCD

9

P.C. B

8

DA23L

13

1

8

2

3

4

10

B

11

5

7

REF. NO PART NO. KANRI DESCRIPTION

1 8A-HC7-007-010 WINDOW,CD
1 8A-HC7-078-010 WINDOW,CD (D)<1AHRJ1D,0Y1BLT>

1 8A-HC7-079-010 WINDOW,CD (L)<1AEZ1L>
2 8A-HC7-005-010 WINDOW,DISPLAY

2 8A-HC7-019-010 WINDOW,DISPLAY 311

2 8A-HC7-020-010 WINDOW,DISPLAY 312<2KS,2AEZ1S>
3 8A-HC7-017-010 LID ASSY,CD

3 8A-HC7-051-010 LID ASSY,CD 310 (D)
3 8A-HC7-052-010 LID ASSY,CD 310 (L)<1AEZ1L>

3 8A-HC7-053-010 LID ASSY,CD 310 (LT)<0Y1BS>
3 8A-HC7-037-010 LID ASSY,CD 311 (LL)<0Y1BLL>

4 85-HC6-205-110 SHAFT,LID(300) HK
5 8A-HC7-204-010 SPR-T,OPEN
6 8A-HC7-018-110 LEVER,OPEN
7 8A-HC7-015-010 CABI ASSY,CENTER

NO.

<EXCEPT 1AHRJ1D,1AEZ1L,0Y1BLT>

<0Y1BLL,0Y1S,1AEZ1S,0Y1BLT,0Y1BS>

<1AHRJ1S,1AHRJ1D,1AEZ1L,1AHABS,0Y1BD>

<EXCEPT 1AHRJ1D,0Y1BLL,1AEZ1L,0Y1BLT,0Y1BS>

<1AHRJ1D,0Y1BLT>

<EXCEPT 1AHRJ1D,0Y1BLL,1AEZ1L,0Y1BLT,0Y1BS>

REF. NO PART NO. KANRI DESCRIPTION

7 8A-HC7-066-010 CABI ASSY,CENTER (D)
7 8A-HC7-065-010 CABI ASSY,CENTER (L)<1AEZ1L>

7 8A-HC7-035-010 CABI ASSY,CENTER (LL)<0Y1BLL>
7 8A-HC7-067-010 CABI ASSY,CENTER (LT)<0Y1BS>
8 8Z-HC1-225-010 DMPR,MECHA(SP)

9 8A-HC7-201-010 GUIDE,LCD
10 8A-HC7-207-010 BAT-CONTACT,(-) (HK)
11 8A-HC7-206-010 BAT-CONTACT,(+) (HK)
12 87-HC8-205-010 BAT-CONTACT,(+)(-)
13 8A-HC7-012-010 KNOB,SL HOLD

14 8A-HC7-016-010 CABI ASSY,BOTTOM
14 8A-HC7-036-010 CABI ASSY,BOTTOM (LL)
14 8A-HC7-075-010 CABI ASSY,BOTTOM (LT)<0Y1BS>

15 88-HC6-021-010 FOOT, DIA10
A 87-067-869-010 V+1.7-8 HL BLK

B 87-067-868-010 V+1.7-4 HL BLK

NO.

<1AHRJ1D,0Y1BLT>

<EXCEPT 1AHRJ1D,0Y1BLL,1AEZ1L,0Y1BLT,0Y1BS>

<1AHRJ1D,0Y1BLL,1AEZ1L,0Y1BLT>

COLOR NAME TABLE

Basic color symbol Color Basic color symbol Color Basic color symbol Color

B Black C Cream D Orange
G Green H Gray L Blue

LT Transparent Blue N Gold P Pink

R Red S Silver ST Titan Silver

12

T Brown V Violet W White

WT Transparent White Y Yellow YT Transparent Yellow

LM Metallic Blue LL Light Blue GT Transparent Green

6

LD Dark Blue DT Transparent Orange

a

14

a

LID,BAT

A

15

2221

CD MECHANISM EXPLODED VIEW 1/1

D

CD MECHANISM PARTS LIST 1/1

D

2

4

REF. NO PART NO. KANRI DESCRIPTION

1 S0-A41-A20-600 PICKUP LASER ASSY
2 SM-10A-108-001 MOTOR ASSY SPINDLE
3 S0-M10-A10-900 MOTOR SLED ASSY
4 S2-311-A12-200 CHASSIS
5 S2-511-A23-200 GEAR MIDDLE

6 S2-511-A23-100 GEAR,SCREW
7 S2-511-A23-400 GEAR,RACK
8 S2-511-A07-900 SPINDLE SCREW
9 S4-S13-A00-200 SW,LEAF
10 S2-451-A18-100 HOLDER GEAR

A SS-EXE-A04-000 SCR PAN PCS 1.4-2.2
B SS-GXE-A00-300 SPECIAL SCREW
C SS-EXE-A14-100 SPECIAL SCREW
D SS-GXE-A00-202 SPECIAL SCREW M1.7-4.0

NO.

9

A

3

5

1

7

8

C

6

10

B

2423

ACCESSORIES/PACKAGE LIST

REF. NO PART NO. KANRI DESCRIPTION

1 8A-HC7-935-010 IB,EZ(EGF)C 311 F<1AEZ1L,0Y1BD>
1 8A-HC7-955-010 IB,EZ(EGF)C 312 F<2KS,2AEZ1S>
1 8A-HC7-937-010 IB,EZ(PHNCZ)C 311 F<1AEZ1L,0Y1BD>
1 8A-HC7-957-010 IB,EZ(PHNCZ)C 312 F<2AEZ1S>
1 8A-HC7-936-010 IB,EZ(SID)C 311 F<1AEZ1L,0Y1BD>

1 8A-HC7-956-010 IB,EZ(SID)C 312 F<2AEZ1S>
1 8A-HC7-902-010 IB,HR(ECA)C<1AHRJ1D>
1 8A-HC7-912-010 IB,HR(ECA)C F<1AHRJ1S,1AHRJ1D>
1 8A-HC7-914-010 IB,LH(3L)C F<1AHABS>
1 8A-HC7-945-010 IB,Y(EGF)C 310 F<0Y1BLL,0Y1S,1AEZ1S,0Y1BLT,0Y1BS>

1 8A-HC7-947-010 IB,Y(PHNCZ)C 310 F<0Y1BLL,0Y1S,1AEZ1S,0Y1BLT,0Y1BS>
1 8A-HC7-946-010 IB,Y(SID)C 310 F<0Y1BLL,0Y1S,1AEZ1S,0Y1BLT,0Y1BS>
2 87-B30-259-010 HEADPHONE,HP-M032(T) L<0Y1BS>
2 87-B30-326-010 HEADPHONE,HP-M048<EXCEPT 0Y1BS>

!

3 87-B30-283-010 AC ADAPTOR,AC-D603ENC<2AEZ1S,1AEZ1L,0Y1BD>

!

3 87-B30-287-010 AC ADAPTOR,AC-D603HANC<1AHABS>

!

3 87-B30-285-110 AC ADAPTOR,AC-D603HRNC<1AHRJ1S,1AHRJ1D>

!

3 87-B30-284-010 AC ADAPTOR,AC-D603KNC<2KS>

!

4 87-A91-017-010 PLUG,CONVERSION JT-0476<1AHRJ1S,1AHRJ1D>

5 87-B30-141-010 BAT,NB-301 NC(2PCS)<2KS,2AEZ1S>

NO.

25

737004

2–11, IKENOHAT A 1–CHOME, TAITO-KU , TOKYO 110, JAPAN TEL:[phone]

Printed in Singapore