Aiwa SXNSZ-20, SXNSZ-22 Schematic

Page 1
NSX-SZ20
EZ, K
NSX-SZ22 NSX-SZ27
SERVICE MANUAL
COMPACT DISC
STEREO SYSTEM
SYSTEM
NSX-SZ20 NSX-SZ22 NSX-SZ27 CX-NSZ27 SX-NSZ20
SYSTEM TAPE MECHANISM CD MECHANISM
NSX-SZ20<EZ> NSX-SZ22<EZ> NSX-SZ27<EZ>
NSX-SZ20<K>
• This Service Manual is the “Revision Publishing” and replaces “Simple Manual” NSX-SZ20/22 (EZ), (S/M Code No. 09-99C-423-4T2) and NSX-SZ27 (EZ),
(S/M Code No. 09-001-423-4T3).
CD
CASSEIVER
CX-NSZ20 SX-NSZ20 CX-NSZ22 SX-NSZ22
BASIC TAPE MECHANISM : ZZM-3 PR1NM / YPR1NF BASIC CD MECHANISM : AZG-1 ZD8RDM / YZD8RDM
SPEAKER
ZZM-3 PR1NM
ZZM-3 YPR1NF AZG-1 YZD8RDM
REMOTE
CONTROLLER
RC-ZAS02
RC-ZAS17
AZG-1 ZD8RDM
• If requiring information about the CD mechanism, see Service Manual
of AZG-1, (S/M Code No. 09-001-335-3N6).
S/M Code No. 09-003-423-4R2
REVISION
DAT A
Page 2
SPECIFICATIONS
<FM tuner section> Tuning range 87.5 MHz to 108 MHz Usable sensitivity (IHF) 16.8 dBf Antenna terminals 75 ohms (unbalanced)
<MW tuner section> Tuning range 531 kHz to 1602 kHz (9 kHz step)
Usable sensitivity 350 µV/m Antenna Loop antenna
<LW tuner section> Tuning range 144 kHz to 290 kHz Usable sensitivity 1400 Antenna Loop antenna
<Amplifier section> Power output Rated : 30 W + 30 W
Total harmonic distortion 0.08% (15 W, 1 kHz, 6 ohms, Inputs VIDEO/AUX: 500 mV
Outputs SPEAKERS: accept speakers of 6
<Cassette deck section> Track format 4 tracks, 2 channels stereo Frequency response 50 Hz – 15 kHz Recording system AC bias Heads Deck 1 : Playback head x 1
530 kHz to 1710 kHz (10 kHz step)
µV/m
(6 ohms, THD 1%, 1 kHz/DIN 45500) Reference : 35 W + 35 W (6 ohms, THD 10%,1 kHz/DIN 45324) DIN MUSIC POWER : 67 W + 67 W
DIN AUDIO)
ohms or more PHONES (stereo jack) : accepts headphones of 32 ohms or more
Deck 2 : Recording/Playback head x 1, erase head x 1
<Compact disc player section> Laser Semiconductor laser (λ =780 nm) D-A converter 1 bit dual Signal-to-noise ratio 85 dB (1 kHz, 0 dB) Harmonic distortion 0.05 % (1 kHz, 0 dB)
<Speaker system> <(20EZ, 20K, 27EZ) : SX–NSZ20, (22EZ) : SX–NSZ22> Speaker System 3 way, bass reflex (magnetic
shielded type)
Speaker units Woofer : 140 mm cone type
Tweeter : 60mm cone type Super tweeter : 20 mm ceramic type
Impedance 6 ohms Output sound pressure level 87 dB/W/m Dimensions (W x H x D) 230 x 324x 256 mm Weight 3.8 kg
<General> Power requirements 230 V AC, 50 Hz Power consumption 80 W Power consumption in standby mode
14 W With power-economizing mode off
0.9 W With power-economizing mode on
Dimensions of main unit 260 x 328 x 335 mm (W x H x D) Weight of main unit 6.2 kg <EZ>
6.3 kg <K>
• Design and specifications are subject to change without notice.
• The word "BBE"and the "BBE symbol" are trademarks of BBE Sound, Inc. Under license from BBE Sound,Inc.
– 2 –
Page 3
PROTECTION OF EYES FROM LASER BEAM DURING SERVICING
This set employs laser. Therefore, be sure to follow carefully the instructions below when servicing.
WARNING!!
WHEN SERVICING, DO NOT APPROACH THE LASER EXIT WITH THE EYE TOO CLOSELY. IN CASE IT IS NECESSARY TO CONFIRM LASER BEAM EMISSION. BE SURE TO OBSERVE FROM A DISTANCE OF MORE THAN 30cm FROM THE SURFACE OF THE OBJEC­TIVE LENS ON THE OPTICAL PICK-UP BLOCK.
s Caution: Invisible laser radiation when
open and interlocks defeated avoid exposure to beam.
s Advarsel: Usynlig laserståling ved åbning,
når sikkerhedsafbrydere er ude af funktion. Undgå udsættelse for stråling.
VAROITUS!
Laiteen Käyttäminen muulla kuin tässä käyttöohjeessa mainitulla tavalla saataa altistaa käyt-täjän turvallisuusluokan 1 ylittävälle näkymättömälle lasersäteilylle.
VARNING!
Om apparaten används på annat sätt än vad som specificeras i denna bruksanvising, kan användaren utsättas för osynling laserstrålning, som överskrider gränsen för laserklass 1.
CAUTION
Use of controls or adjustments or performance of proce­dures other than those specified herin may result in hazardous radiation exposure.
ATTENTION
L’utillisation de commandes, réglages ou procédures autres que ceux spécifiés peut entraîner une dangereuse exposition aux radiations.
ADVARSEL
Usynlig laserståling ved åbning, når sikkerhedsafbrydereer ude af funktion. Undgå udsættelse for stråling.
This Compact Disc player is classified as a CLASS 1 LASER product. The CLASS 1 LASER PRODUCT label is located on the rear exterior.
CLASS 1 LASER PRODUCT KLASSE 1 LASER PRODUKT LUOKAN 1 LASER LAITE KLASS 1 LASER APPARAT
Precaution to replace Optical block (KSM-880CAB)
Body or clothes electrostatic potential could ruin laser diode in the optical block. Be sure ground body and workbench, and use care the clothes do not touch the diode.
1) After the connection, remove solder shown in the right figure.
PICK-UP Assy P.C.B
solder
– 3 –
Page 4
NOTE ON BEFORE STARTING REPAIR
1. Forced discharge of electrolytic capacitor of power supply block
When repair is going to be attempted in the set that uses relay circuit in the power supply block, electric potential is kept charged across the electrolytic capacitors (C101, 102) even though AC power cord is removed. If repair is attempted in this condition, secondary defect can occur. In order to prevent the secondary trouble, perform the following measures before starting repair work.
Discharge procedure
1 Remove the AC power cord. 2 Connect a discharging resistor at an end of lead wire that
has clips at both ends. Connect the other end of the lead wire to metal chassis.
3 Contact the other end of the discharging resistor to the
positive (+) side (+VH) of C101. (For two seconds)
4 Contact the same end of the discharging resistor as step 3
to the negative (-) side (-VH) of C102 in the same way. (For two seconds)
5 Check that voltage across C101 and C102 has decreased
to 1 V or less using a multimeter or an oscilloscope.
Select a discharging resistor referring to the following table.
Charging voltage (V) Discharging
(C101, 102) resistor (Ω)
25-48 100 3 87-A00-247-090
49-140 220 5 87-A00-232-090
Note: The reference numbers (C101, C102) of the electrolytic capacitors can change depending on the models. Be sure to check the
reference numbers of the charging capacitors on schematic diagram before starting the discharging work.
Rated power (W) Parts number
MAIN C.B
D101
3
C101 C102
22
Fig-1
4
2. Check items before exchanging the MICROCOMPUTER
Be sure to check the following items before exchanging the MICROCOMPUTER. Exchange the MICROCOMPUTER after confirming that the MICROCOMPUTER is surely defective.
2-1. Regarding the HOLD terminal of the MICROCOMPUTER
When the HOLD terminal (INPUT) of the MICROCOMPUTER is “H”, the MICROCOMPUTER is judged to be operating correctly. When this terminal is “L”, the main power cannot be turned on. Therefore, be sure to check the terminal voltage of the HOLD terminal before exchange. When the MICROCOMPUTER is not defective, the HOLD terminal can also go “L” when the POWER AMPLIFIER has any abnormalities that triggers the abnormality detection circuit on the MAIN C. B. that sets the HOLD terminal to “L”.
• Good or no good judgement of the MICROCOMPUTER
1 Turn on the AC main power. 2 Confirm that the main power is turned on and the HOLD terminal of the MICROCOMPUTER keeps the “H” level or not. 3 When the HOLD terminal is “L” level, the abnormality detection circuit is judged to be working correctly and the
MICROCOMPUTER is judged to be good.
– 4 –
Page 5
In such a case, check also if the POWER AMPLIFIER circuit or power supply circuit has any abnormalities or not.
2-2. Regarding reset
There are cases that the machine does not work correctly because the MICROCOMPUTER is not reset even though the AC power cord is re-inserted, or the software reset (pressing the STOP key + POWER key) is performed. When the above described phenomenon occurs, it can lead to wrong judgement as if the MICROCOMPUTER is defective and to exchange the MICROCOMPUTER. In such a case, perform the forced-reset by the following procedure and check good or no good of the MICROCOMPUTER.
1 Remove the AC power cord.
PUTER
ICROCOM
M
FRONT C.B
2 Short both ends of the electrolytic capacitor C113 that is connected to VDD of the MICROCOMPUTER with tweezers. 3 Connect the AC power cord again. If the MICROCOMPUTER returns to the normal operation, the MICROCOMPUTER is
good.
Note: The reference number or MICROCOMPUTER pin number of transistor (Q110) and electrolytic capacitor (C113) can change depending
on the models. Be sure to check the reference numbers on schematic diagram before starting the discharging work.
18
15
C113
Short with tweezers.
Fig-2-2
C113
FRONT C.B
%
VSS
*
VDD
MICRO­COMPUTER
2-3. Confirmation of soldering state of MICROCOMPUTER
Check the soldering state of the MICROCOMPUTER in addition to the above described procedures. Be sure to exchange the MICROCOMPUTER after surely confirming that the trouble is not caused by poor soldering but the MICROCOMPUTER itself.
– 5 –
Page 6
ELECTRICAL MAIN PARTS LIST
PART NO. DESCRIPTIONREF. NO. KANRI
NO.
IC
87-A21-397-010 IC,STK490-070 87-A21-419-040 IC,NJM14558MD-TE2 87-A21-401-040 C-IC,M61503FP 87-A21-415-010 IC,LA1843 87-A20-440-040 C-IC,BU1920FS<22EZ>
8A-NF9-601-010 C-IC,UPD780226GF-012-3BA<20EZ> 8A-NF9-602-010 C-IC,UPD780226GF-059-3BA<22EZ> 8A-NF9-601-110 C-IC,UPD780226GF-014-3BA<20K,27EZ> 87-A21-482-010 IC,RPM6938-H4 87-070-127-110 IC,LC72131 D
87-A21-269-010 IC,EW732
TRANSISTOR
87-026-609-080 TR,KTA1266GR 89-213-702-010 TR,2SB1370 (1.8W) 87-026-610-080 TR,KTC3198GR 87-A30-076-080 C-TR,2SC3052F 87-A30-075-080 C-TR,2SA1235F
87-026-245-080 TR,DTC114ES 87-A30-198-080 TR,KTC3199GR 87-A30-074-080 C-TR,RT1P 141C 87-A30-073-080 C-TR,RT1N 141C 87-A30-107-070 C-TR,CMBT5401
87-A30-106-040 C-TR,CMBT5551 87-026-235-080 CHIP-TR,DTC114EK 87-A30-087-080 C-FET,2SK2158 87-A30-091-080 FET,2SJ460 87-A30-090-080 FET,2SK2541
87-A30-104-080 C-TR,RT1N 441C 89-333-317-880 TR,2SC3331 (0.5W) 87-A30-318-080 TR,CSA952K 87-A30-329-080 TR,CD1585BC 89-327-143-080 TR,2SC2714 (0.1W)
87-A30-072-080 C-TR,RT1P 144C 87-A30-234-080 TR,CSC4115BC 87-A30-468-080 C-TR,KRC102S-RTK 87-A30-086-040 C-TR,CSD1306E 89-503-602-080 C-FET 2SK360E
87-A30-062-080 C-TR,KRC104S
DIODE
87-A40-553-080 DIODE,1N4003 LES 87-A40-776-080 ZENER,UZ27BSD 87-A40-764-080 ZENER,UZ10BSC 87-A40-313-080 C-DIODE,MC 2840 87-A40-270-080 C-DIODE,MC2838
87-A40-269-080 C-DIODE,MC2836 87-A40-752-080 ZENER,UZ6.2BSC 87-A40-739-080 ZENER,UZ2.7BSA 87-017-149-080 ZENER,HZS6A2L 87-020-465-080 DIODE,1SS133
87-A40-854-080 ZENER,UZ15BSA
MAIN C.B
C3 87-012-368-080 C-CAP,S 0.1-50 F C4 87-012-368-080 C-CAP,S 0.1-50 F C5 87-012-368-080 C-CAP,S 0.1-50 F C6 87-012-368-080 C-CAP,S 0.1-50 F C9 87-012-368-080 C-CAP,S 0.1-50 F
C10 87-012-368-080 C-CAP,S 0.1-50 F C11 87-012-368-080 C-CAP,S 0.1-50 F C12 87-012-368-080 C-CAP,S 0.1-50 F C19 87-A10-627-000 CAP,E 2200-50 SMG C20 87-A10-627-000 CAP,E 2200-50 SMG
DESCRIPTIONREF. NO. KANRI
C21 87-A10-520-000 CAP,E 3300-35 M SMG C22 87-A10-520-000 CAP,E 3300-35 M SMG C25 87-010-385-080 CAP, ELECT 220-25V C26 87-010-247-080 CAP, ELECT 100-50V C30 87-010-430-080 CAP, ELECT 100-63
C31 87-010-263-080 CAP, ELECT 100-10V C32 87-010-197-080 CAP, CHIP 0.01-25 K B C34 87-010-247-080 CAP, ELECT 100-50V C35 87-010-380-080 CAP, ELECT 47-16V M 11L C36 87-010-381-080 CAP, ELECT 330-16V
C38 87-010-197-080 CAP, CHIP 0.01-25 K B C60 87-010-403-080 CAP, ELECT 3.3-50V C61 87-010-260-080 CAP, ELECT 47-25V C97 87-010-196-080 CHIP CAPACITOR,0.1-25 C99 87-010-196-080 CHIP CAPACITOR,0.1-25
C101 87-010-185-080 C-CAP,S 3900P-50 B C102 87-010-185-080 C-CAP,S 3900P-50 B C103 87-010-545-080 CAP, ELECT 0.22-50V SME C104 87-010-545-080 CAP, ELECT 0.22-50V SME C105 87-010-187-080 CHIP CAP 5600P-50 K B
C106 87-010-187-080 CHIP CAP 5600P-50 K B C107 87-010-404-080 CAP, ELECT 4.7-50V C108 87-010-404-080 CAP, ELECT 4.7-50V C109 87-010-322-080 C-CAP,S 100P-50 CH C110 87-010-322-080 C-CAP,S 100P-50 CH
C111 87-010-391-080 CAP,E 10-35 SME C112 87-010-391-080 CAP,E 10-35 SME C113 87-010-405-080 CAP, ELECT 10-50V C114 87-010-405-080 CAP, ELECT 10-50V C119 87-010-197-080 C-CAP,S 0.01-25 K B
C120 87-010-197-080 C-CAP,S 0.01-25 K B C123 87-010-176-080 C-CAP,S 680P-50 J SL C124 87-010-176-080 C-CAP,S 680P-50 J SL C125 87-012-368-080 C-CAP,S 0.1-50 F C126 87-012-368-080 C-CAP,S 0.1-50 F
C127 87-012-368-080 C-CAP,S 0.1-50 F C128 87-012-368-080 C-CAP,S 0.1-50 F C129 87-010-191-080 C-CAP,S 0.015-50 F C130 87-010-191-080 C-CAP,S 0.015-50 F C131 87-010-197-080 CAP, CHIP 0.01-25 K B
C132 87-010-197-080 CAP, CHIP 0.01-25 K B C133 87-010-186-080 CAP,CHIP 4700P-50 K C140 87-010-182-080 C-CAP,S 2200P-50 B C141 87-010-196-080 CHIP CAPACITOR,0.1-25 C239 87-010-196-080 CHIP CAPACITOR,0.1-25
C301 87-010-178-080 C-CAP,S 1000-50 K B C302 87-010-178-080 C-CAP,S 1000-50 K B C303 87-010-178-080 C-CAP,S 1000-50 K B C304 87-010-178-080 C-CAP,S 1000-50 K B C307 87-010-263-080 CAP, ELECT 100-10V
C308 87-010-263-080 CAP, ELECT 100-10V C309 87-010-318-080 C-CAP,S 47P-50 CH C310 87-010-318-080 C-CAP,S 47P-50 CH C313 87-010-188-080 CAP,CHIP 6800P-50 K C314 87-010-188-080 CAP,CHIP 6800P-50 K
C315 87-010-263-080 CAP, ELECT 100-10V C317 87-010-546-080 CAP, ELECT 0.33-50V C318 87-010-546-080 CAP, ELECT 0.33-50V C326 87-010-198-080 CAP, CHIP 0.022-25 K C327 87-012-368-080 C-CAP,S 0.1-50 F
C360 87-010-401-080 CAP, ELECT 1-50V C399 87-012-140-080 C-CAP,S 470P-50 J C401 87-010-544-080 CAP, ELECT 0.1-50V C402 87-010-544-080 CAP, ELECT 0.1-50V C403 87-010-321-080 CHIP CAPACITOR,82P(J)
C404 87-010-321-080 CHIP CAPACITOR,82P(J) C405 87-010-197-080 CAP, CHIP 0.01-25 K B C406 87-010-197-080 CAP, CHIP 0.01-25 K B C407 87-010-197-080 CAP, CHIP 0.01-25 K B C408 87-010-197-080 CAP, CHIP 0.01-25 K B
PART NO.
NO.
– 6 –
Page 7
PART NO. DESCRIPTIONREF. NO. KANRI
NO.
C409 87-010-182-080 C-CAP,S 2200P-50 B C410 87-010-182-080 C-CAP,S 2200P-50 B C411 87-010-405-080 CAP, ELECT 10-50V C412 87-010-405-080 CAP, ELECT 10-50V C452 87-010-382-080 CAP, ELECT 22-25V
C453 87-010-183-080 C-CAP,S 2700P-50 B C454 87-010-183-080 C-CAP,S 2700P-50 B C455 87-010-183-080 C-CAP,S 2700P-50 B C456 87-010-197-080 CAP, CHIP 0.01-25 K B C460 87-010-196-080 CHIP CAPACITOR,0.1-25
C461 87-012-158-080 C-CAP,S 390P-50 CH C462 87-012-158-080 C-CAP,S 390P-50 CH C458 87-010-178-080 C-CAP,S 1000-50 K B C459 87-010-175-080 C-CAP,S 560P-50 J SL C605 87-010-179-080 CAP,CHIP S 1200P-50 K
C606 87-010-179-080 CAP,CHIP S 1200P-50 K C609 87-010-213-080 C-CAP,S 0.015-50 B C610 87-010-213-080 C-CAP,S 0.015-50 B C611 87-010-545-080 CAP, ELECT 0.22-50V C612 87-010-545-080 CAP, ELECT 0.22-50V
C613 87-010-545-080 CAP, ELECT 0.22-50V C614 87-010-545-080 CAP, ELECT 0.22-50V C615 87-010-154-080 CAP CHIP 10P-50 CH C616 87-010-221-080 CAP, ELECT 470-10V SME C617 87-010-221-080 CAP, ELECT 470-10V SME
C618 87-010-405-080 CAP, ELECT 10-50V C630 87-016-669-080 C-CAP,S 0.1-25 K B C631 87-010-185-080 C-CAP,S 3900P-50 B C632 87-010-185-080 C-CAP,S 3900P-50 B C633 87-016-369-080 C-CAP,S 0.033-25 K B
C634 87-016-369-080 C-CAP,S 0.033-25 K B C669 87-010-322-080 C-CAP,S 100P-50 CH C670 87-010-322-080 C-CAP,S 100P-50 CH C677 87-010-197-080 CAP, CHIP 0.01-25 K B C779 87-010-971-080 C-CAP,S 4700P-50 J B
C780 87-010-971-080 C-CAP,S 4700P-50 J B C771 87-010-263-080 CAP, ELECT 100-10V C772 87-010-197-080 CAP, CHIP 0.01-25 K B C779 87-A10-801-080 C-CAP,S 0.022-16 J B C780 87-A10-801-080 C-CAP,S 0.022-16 J B
C782 87-010-197-080 CAP, CHIP 0.01-25 K B C783 87-010-197-080 CAP, CHIP 0.01-25 K B C784 87-010-197-080 CAP, CHIP 0.01-25 K B C785 87-010-197-080 CAP, CHIP 0.01-25 K B C786 87-010-197-080 CAP, CHIP 0.01-25 K B
C788 87-010-149-080 C-CAP,S 5P-50 CH C789 87-A11-532-080 C-CAP,S 0.022-50 J C790 87-A11-532-080 C-CAP,S 0.022-50 J C791 87-010-196-080 CHIP CAPACITOR,0.1-25 C792 87-010-197-080 CAP, CHIP 0.01-25 K B
C793 87-010-404-080 CAP, ELECT 4.7-50V C795 87-010-197-080 CAP, CHIP 0.01-25 K B C796 87-010-197-080 CAP, CHIP 0.01-25 K B C797 87-010-405-080 CAP, ELECT 10-50V C798 87-010-197-080 CAP, CHIP 0.01-25 K B
C799 87-010-407-080 CAP, ELECT 33-50V C800 87-012-369-080 C-CAP,S 0.047-50F C801 87-010-403-080 CAP, ELECT 3.3-50V C802 87-010-194-080 CAP, CHIP 0.047-25 Z F C803 87-010-198-080 CAP, CHIP 0.022-25 K B
C804 87-010-263-080 CAP, ELECT 100-10V C807 87-010-400-080 CAP, ELECT 0.47-50V C808 87-010-401-080 CAP, ELECT 1-50V C809 87-010-401-080 CAP, ELECT 1-50V C810 87-010-196-080 CHIP CAPACITOR,0.1-25
C814 87-010-197-080 CAP, CHIP 0.01-25 K B C815 87-010-400-080 CAP, ELECT 0.47-50V C816 87-010-400-080 CAP, ELECT 0.47-50V C818 87-010-180-080 C-CAP,S 1000P-50 J CH C821 87-010-405-080 CAP, ELECT 10-50V
DESCRIPTIONREF. NO. KANRI
PART NO.
NO.
C823 87-012-349-080 C-CAP,S 1000P-50 J CH C824 87-010-405-080 CAP, ELECT 10-50V C825 87-010-596-080 CAP, S 0.047-16 C831 87-010-406-080 CAP, ELECT 22-50 M SME C842 87-010-197-080 CAP, CHIP 0.01-25 K B
C844 87-010-197-080 CAP, CHIP 0.01-25 K B C850 87-010-260-080 CAP, ELECT 47-25V C851 87-010-197-080 CAP, CHIP 0.01-25 K B C852 87-010-197-080 CAP, CHIP 0.01-25 K B C853 87-010-197-080 CAP, CHIP 0.01-25 K B
C858 87-010-196-080 CHIP CAPACITOR,0.1-25 C859 87-010-196-080 CHIP CAPACITOR,0.1-25 C860 87-010-197-080 CAP, CHIP 0.01-25 K B C869 87-010-197-080 CAP, CHIP 0.01-25 K B<22EZ> C871 87-012-156-010 C-CAP,S 2200P-50 J CH<22EZ>
C872 87-012-156-010 C-CAP,S 2200P-50 J CH<22EZ> C873 87-012-140-080 C-CAP,S 470P-50 J CH<22EZ> C874 87-010-405-080 CAP, ELECT 10-50V<22EZ> C876 87-010-405-080 CAP, ELECT 10-50V<22EZ> C877 87-010-197-080 CAP, CHIP 0.01-25 K B<22EZ>
C878 87-010-316-080 C-CAP,S 33P-50 J CH GRM<22EZ> C879 87-010-314-080 C-CAP,S 22P-50 J CH GRM<22EZ> C940 87-010-197-080 CAP, CHIP 0.01-25 K B C942 87-010-149-080 C-CAP,S 5P-50 CH C947 87-010-197-080 CAP, CHIP 0.01-25 K B
C948 87-012-140-080 C-CAP,S 470P-50 J CH C952 87-010-197-080 CAP, CHIP 0.01-25 K B C957 87-010-311-080 C-CAP,S 12P-50 J CH C958 87-010-197-080 CAP, CHIP 0.01-25 K B C959 87-010-196-080 CHIP CAPACITOR,0.1-25
C960 87-010-196-080 CHIP CAPACITOR,0.1-25 C961 87-010-152-080 C-CAP,S 8P-50 CH C962 87-010-401-080 CAP, ELECT 1-50V C963 87-015-785-080 CHIP CAPACITOR, 0.1FZ-25Z C971 87-010-381-080 CAP, ELECT 330-16V
C972 87-010-404-080 CAP, ELECT 4.7-50V C973 87-010-197-080 CAP, CHIP 0.01-25 K B C974 87-010-197-080 CAP, CHIP 0.01-25 K B C979 87-010-322-080 C-CAP,S 100P-50 CH C981 87-010-260-080 CAP, ELECT 47-25V
C982 87-010-196-080 CHIP CAPACITOR,0.1-25 C983 87-010-197-080 CAP, CHIP 0.01-25 K B C984 87-010-197-080 CAP, CHIP 0.01-25 K B C985 87-010-322-080 C-CAP,S 100P-50 J CH C987 87-010-197-080 CAP, CHIP 0.01-25 K B
C989 87-010-197-080 CAP, CHIP 0.01-25 K B C991 87-010-312-080 C-CAP,S 15P-50 CH C992 87-010-312-080 C-CAP,S 15P-50 CH C993 87-010-178-080 CHIP CAP 1000P-50 K B C995 87-010-178-080 CHIP CAP 1000P-50 K B
C997 87-010-196-080 CHIP CAPACITOR,0.1-25 C998 87-010-260-080 CAP, ELECT 47-25V C999 87-A11-155-080 CAP,TC U 0.01-16 Z F CF831 87-008-423-010 FILTER, SFE10.7MS3G-A CF832 82-785-747-010 CF, MS2 GHYR
CN301 87-A60-620-010 CONN,3P V 2MM JMT CN351 87-A60-625-010 CONN,8P V 2MM JMT CN601 87-099-719-010 CONN,30P TYK-B(X) CN602 87-A60-131-010 CONN,6P V FE D951 87-A40-618-080 VARI-CAP,SVC 348
FC602 88-906-251-110 FF-CABLE,6P 1.25 FB303 87-008-474-080 F-BEAD BL02RN1-R62T2 EMI FFE831 A8-6ZA-19C-170 6ZA-1 YFEENC<20K> FFE831 A8-6ZA-191-030 6ZA-1 FEENM<20EZ,22EZ,27EZ> J202 87-A60-488-010 JACK,DIA6.3 BLK ST W/SW KM16AT
J203 87-A60-238-010 TERMINAL,SP 4P (MSC) J602 87-A60-881-010 JACK,PIN 2P MSP 242V05 PBSN J832 87-A60-403-010 TERMINAL,ANT PAL 2P HSP-312V05 L101 87-A50-610-010 COIL,1UH-K L102 87-A50-610-010 COIL,1UH-K
– 7 –
Page 8
PART NO. DESCRIPTIONREF. NO. KANRI
NO.
L451 87-007-342-010 COIL,OSC 85K BIAS L801 87-A50-540-010 COIL,FM DET(TOK) L802 87-A91-551-010 FLTR,PCFJZH-450 L(TOK) L811 87-005-847-080 COIL,2.2UH(CECS) L832 87-005-847-080 COIL,2.2UH(CECS)
L941 87-A50-020-010 COIL,ANT LW(COI) 252KHZ L942 87-A50-019-010 COIL,OSC LW(COI) 856KHZ L951 8A-NF8-668-010 COIL,AM PACK 2(TOK) R131 87-A00-258-080 RES,M/F 0.22-1W J R132 87-A00-258-080 RES,M/F 0.22-1W J
R143 87-A00-440-050 RES,220-1/2W J RP R144 87-A00-440-050 RES,220-1/2W J RP R145 87-A00-440-050 RES,220-1/2W J RP R146 87-A00-440-050 RES,220-1/2W J RP R653 87-A11-144-080 CAP,TC U 0.1-50 KB
R654 87-A11-144-080 CAP,TC U 0.1-50 KB R790 87-010-197-080 CAP, CHIP 0.01 DM R991 87-010-322-080 C-CAP,S 100P-50 CH R993 87-010-322-080 C-CAP,S 100P-50 CH R995 87-010-322-080 C-CAP,S 100P-50 CH
SFR451 87-A90-432-080 SFR,30K H NVZ6TLTA SFR452 87-A90-432-080 SFR,30K H NVZ6TLTA TC942 87-011-253-080 TRIMMER,CER 30P 4.0X4.5 ECRLA W99 8A-NF9-609-010 F-CABLE,9P 2.5 480MM WH1 87-A90-510-010 HLDR,WIRE 2.5-9P
X861 87-A70-091-010 VIB,XTAL 4.332MHZ CSA-309 X991 87-A70-061-010 VIB,XTAL 4.500MHZ CSA-309
FRONT C.B
C101 87-010-196-080 CHIP CAPACITOR,0.1-25 C102 87-010-196-080 CHIP CAPACITOR,0.1-25 C103 87-010-498-040 CAP,E 10-16 M 5L C104 87-010-196-080 CHIP CAPACITOR,0.1-25 C107 87-010-493-040 CAP,E 0.47-50 M 5L
C108 87-012-393-080 C-CAP,S 0.22-16 K C153 87-010-198-080 CAP, CHIP 0.022-25 K B C154 87-010-246-040 CAP,E 47-35 SME C155 87-010-404-040 CAP,E 4.7-50 SME C156 87-010-404-040 CAP,E 4.7-50 SME
C361 87-010-178-080 CHIP CAP 1000P-50 K B C362 87-010-178-080 CHIP CAP 1000P-50 K B C371 87-010-178-080 CHIP CAP 1000P-50 K B C372 87-010-178-080 CHIP CAP 1000P-50 K B C601 87-010-382-040 CAP,E 22-25 SME
C801 87-010-195-080 C-CAP,S 0.068-25 F C802 87-010-195-080 C-CAP,S 0.068-25 F C803 87-010-402-040 CAP,E 2.2-50 SME C804 87-010-402-040 CAP,E 2.2-50 SME C805 87-010-196-080 CHIP CAPACITOR,0.1-25
C806 87-010-196-080 CHIP CAPACITOR,0.1-25 C901 87-010-322-080 C-CAP,S 100P-50 CH C902 87-010-322-080 C-CAP,S 100P-50 CH C903 87-010-322-080 C-CAP,S 100P-50 CH C904 87-010-322-080 C-CAP,S 100P-50 CH
C905 87-010-322-080 C-CAP,S 100P-50 CH C906 87-010-322-080 C-CAP,S 100P-50 CH C907 87-010-322-080 C-CAP,S 100P-50 CH C908 87-010-322-080 C-CAP,S 100P-50 CH C909 87-010-322-080 C-CAP,S 100P-50 CH
C910 87-010-322-080 C-CAP,S 100P-50 CH C911 87-010-178-080 CHIP CAP 1000P-50 K B C912 87-010-196-080 CHIP CAPACITOR,0.1-25 C913 87-010-248-040 CAP,E 220-10 SME C914 87-010-248-040 CAP,E 220-10 SME
C915 87-010-196-080 CHIP CAPACITOR,0.1-25 C916 87-010-196-080 CHIP CAPACITOR,0.1-25 C917 87-010-196-080 CHIP CAPACITOR,0.1-25 C919 87-010-197-080 CAP, CHIP 0.01-25 K B C920 87-012-369-080 C-CAP,S 0.047-50 Z F
DESCRIPTIONREF. NO. KANRI
PART NO.
NO.
C921 87-010-186-080 CAP,CHIP 4700P-50 K B C951 87-010-312-080 C-CAP,S 15P-50 CH C952 87-012-155-080 C-CAP 180P-50CH C953 87-012-140-080 CAP 470P-50 CH C961 87-010-378-040 CAP,E 10-16 M SME
C962 87-012-157-080 C-CAP,S 330P-50 CH C963 87-010-196-080 CHIP CAPACITOR,0.1-25 CN104 87-A60-057-010 CONN,11P V 9604S-11C CN701 87-099-720-010 CONN,30P BLK TYK-B(P) CN731 87-099-015-010 CONN,13P V BLK 6216V
FC104 88-911-101-110 FF-CABLE,11P 1.25 FC731 88-913-301-110 FF-CABLE,13P-1.25 FL901 8A-NF9-605-010 FL,HNA-10SS12 L951 87-A50-434-010 COIL,CLK 4.19M(TOKO) LED201 87-A40-619-040 LED,SLR-56PT-T31-W GRN
LED202 87-A40-619-040 LED,SLR-56PT-T31-W GRN LED204 87-A40-619-040 LED,SLR-56PT-T31-W GRN LED205 87-A40-619-040 LED,SLR-56PT-T31-W GRN LED209 87-A40-317-080 LED,SLR-342VCT31 RED LED210 87-A40-619-040 LED,SLR-56PT-T31-W GRN
S301 87-A91-024-180 SW,TACT KSH0611BT<20EZ,20K,22EZ> S301 87-A90-164-080 SW,TACT SKQNAB(N)<27EZ> S302 87-A91-024-180 SW,TACT KSH0611BT<20EZ,20K,22EZ> S302 87-A90-164-080 SW,TACT SKQNAB(N)<27EZ> S303 87-A91-024-180 SW,TACT KSH0611BT<20EZ,20K,22EZ>
S303 87-A90-164-080 SW,TACT SKQNAB(N)<27EZ> S304 87-A91-024-180 SW,TACT KSH0611BT<20EZ,20K,22EZ> S304 87-A90-164-080 SW,TACT SKQNAB(N)<27EZ> S305 87-A91-024-180 SW,TACT KSH0611BT<20EZ,20K,22EZ> S305 87-A90-164-080 SW,TACT SKQNAB(N)<27EZ>
S306 87-A91-024-180 SW,TACT KSH0611BT<20EZ,20K,22EZ> S306 87-A90-164-080 SW,TACT SKQNAB(N)<27EZ> S307 87-A91-024-180 SW,TACT KSH0611BT<20EZ,20K,22EZ> S307 87-A90-164-080 SW,TACT SKQNAB(N)<27EZ> S308 87-A91-024-180 SW,TACT KSH0611BT<20EZ,20K,22EZ>
S308 87-A90-164-080 SW,TACT SKQNAB(N)<27EZ> S309 87-A91-024-180 SW,TACT KSH0611BT<20EZ,20K,22EZ> S309 87-A90-164-080 SW,TACT SKQNAB(N)<27EZ> S321 87-A91-024-180 SW,TACT KSH0611BT<20EZ,20K,22EZ> S321 87-A90-164-080 SW,TACT SKQNAB(N)<27EZ>
S322 87-A91-024-180 SW,TACT KSH0611BT<20EZ,20K,22EZ> S322 87-A90-164-080 SW,TACT SKQNAB(N)<27EZ> S323 87-A91-024-180 SW,TACT KSH0611BT<20EZ,20K,22EZ> S323 87-A90-164-080 SW,TACT SKQNAB(N)<27EZ> S324 87-A91-024-180 SW,TACT KSH0611BT<20EZ,20K,22EZ>
S324 87-A90-164-080 SW,TACT SKQNAB(N)<27EZ> S325 87-A91-024-180 SW,TACT KSH0611BT<20EZ,20K,22EZ> S325 87-A90-164-080 SW,TACT SKQNAB(N)<27EZ> S326 87-A91-024-180 SW,TACT KSH0611BT<20EZ,20K,22EZ> S326 87-A90-164-080 SW,TACT SKQNAB(N)<27EZ>
S327 87-A91-024-180 SW,TACT KSH0611BT<22EZ> S328 87-A91-024-180 SW,TACT KSH0611BT<22EZ> S329 87-A91-024-180 SW,TACT KSH0611BT<22EZ> S341 87-A91-024-180 SW,TACT KSH0611BT<20EZ,20K,22EZ> S341 87-A90-164-080 SW,TACT SKQNAB(N)<27EZ>
S342 87-A91-024-180 SW,TACT KSH0611BT<20EZ,20K,22EZ> S342 87-A90-164-080 SW,TACT SKQNAB(N)<27EZ> S343 87-A91-024-180 SW,TACT KSH0611BT<20EZ,20K,22EZ> S343 87-A90-164-080 SW,TACT SKQNAB(N)<27EZ> S344 87-A91-024-180 SW,TACT KSH0611BT<20EZ,20K,22EZ>
S344 87-A90-164-080 SW,TACT SKQNAB(N)<27EZ> S345 87-A91-024-180 SW,TACT KSH0611BT<20EZ,20K,22EZ> S345 87-A90-164-080 SW,TACT SKQNAB(N)<27EZ> S346 87-A91-024-180 SW,TACT KSH0611BT<20EZ,20K,22EZ> S346 87-A90-164-080 SW,TACT SKQNAB(N)<27EZ>
S347 87-A91-024-180 SW,TACT KSH0611BT<20EZ,20K,22EZ> S347 87-A90-164-080 SW,TACT SKQNAB(N)<27EZ> S348 87-A91-024-180 SW,TACT KSH0611BT<20EZ,20K,22EZ> S348 87-A90-164-080 SW,TACT SKQNAB(N)<27EZ> S349 87-A91-024-180 SW,TACT KSH0611BT<20EZ,20K,22EZ>
– 8 –
Page 9
PART NO.
S349 87-A90-164-080 SW,TACT SKQNAB(N)<27EZ> S350 87-A91-024-180 SW,TACT KSH0611BT<20EZ,20K,22EZ> S350 87-A90-164-080 SW,TACT SKQNAB(N)<27EZ> S361 87-A91-633-010 SW,RTRY XRE012103PVB25FINA 1-2 S371 87-A91-632-010 SW,RTRY XRE012103PVB25FINB 1-2
PT C.B
C183 87-010-387-080 CAP,E 470-25 SME C184 87-010-403-080 CAP, ELECT 3.3-50V
!
PT1 8A-NF9-612-010 PT,ANF-9 U
!
PT181 8A-NF8-662-010 PT,SUB ANF-8 (E) RY181 87-A91-418-010 RELAY,AC12V G5PA-1-M
!
!
T181 87-A60-317-010 TERMINAL, 1P MSC
!
T182 87-A60-317-010 TERMINAL, 1P MSC WH181 87-A90-510-010 HLDR,WIRE 2.5-9P
DECK C.B
HL1 8Z-ZM3-214-010 HLDR,IC CN1 87-099-753-010 CONN,11P H 9604 SFR1 87-024-581-010 SFR,3.3K DIA6V K0A SW1 87-A90-673-010 SW,MICRO ESE11SH1C SW2 87-A91-500-010 SW,MICRO MPU11470MLB0
SW3 87-A91-500-010 SW,MICRO MPU11470MLB0 SW4 87-A91-500-010 SW,MICRO MPU11470MLB0 SW5 87-A90-673-010 SW,MICRO ESE11SH1C
NO.
DESCRIPTIONREF. NO. KANRI
CHIP RESISTOR PART CODE
Chip Resistor Part Coding
88
A
Resistor Code
Chip resistor
Wattage Type Tolerance 1/16W 1005 5% CJ
1/16W 1/10W
1/8W
1608 2125
3216
5% 5%
5%
Symbol
CJ CJ
CJ
Figure
Value of resistor
Form
L
Dimensions (mm)
t
W
0.55
Resistor Code
108 118
128
LW t
1.0 0.5 0.35 104
1.6 0.8 0.45 2 1.25 0.45
3.2
1.6
: A : A
– 9 –
Page 10
TRANSISTOR ILLUSTRATION
E C B
CD1585BC CSA952K KTA1266GR KTC3198GR
E C B
DTC114ES KTC3199GR
S
E C B
2SC3331 2SB1370
S D G
2SJ460 2SK2541
E C B B C E
CSC4115BC
D
G
S
2SK2158
B
2SA1235F 2SC2714 2SC3052F CMBT5401 CMBT5551 CSD1306E
C
E
DTC114EK KRC102S KRC104S RT1N141C RT1N441C RT1P141C RT1P144C
D
G
2SK360E
– 10 –
Page 11
FL (HNA-10SS12) GRID ASSIGNMENT AND ANODE CONNECTION
GRID ASSIGNMENT
ANODE CONNECTION
– 11 –
Page 12
WIRING - 1 (MAIN)
101112131415161718192021222324
1234567892526272829303132
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
– 12 –
R
S
T
U
Page 13
SCHEMATIC DIAGRAM – 1 (MAIN 1 / 2 : AMP)
13
Page 14
SCHEMATIC DIAGRAM – 2 (MAIN 2 / 2 : TUNER)
14
Page 15
WIRING - 2 (FRONT)
101112131415161718192021222324
1234567892526272829303132
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
– 15 –
R
S
T
U
Page 16
SCHEMATIC DIAGRAM – 3 (FRONT)
16
Page 17
WIRING - 3 (PT)
123456789101112131415
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
– 17 –
R
S
T
U
Page 18
SCHEMATIC DIAGRAM – 4 (PT)
– 18 –
Page 19
WIRING – 4 (DECK)
101112131415161718192021222324
1234567892526272829303132
D DECK C . B
FROM
B
FRONT C. B CN104
FC104
1 3
5
7911
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
– 19 –
S
T
U
Page 20
IC BLOCK DIAGRAM
IC, LA1843
IC, LC72131D
– 20 –
Page 21
IC, BU1920FS <22EZ ONLY>
IC, M61503FP
– 21 –
Page 22
IC DESCRIPTION
IC, µPD780226GF-012-3BA / 014-3BA / 059-3BA
Pin No.
1 O-MOTOR O DECK MOTOR ON/OFF output. 2 O-SOL1 O DECK1 solenoid output. 3 O-SOL2 O DECK2 solenoid output. 4 NC Not connected. 5 NC Not connected. 6 O-SET_LED O SET LED ON/OFF output. 7 O-CLEAR_LED O CLEAR LED ON/OFF output. 8 O-PRESET_LED O PRESET LED ON/OFF output.
9 O-DOWN_LED O DOWN LED ON/OFF output. 10 O-UP_LED O UP LED ON/OFF output. 11 O-TUNER_ON O TUNER ON output. 12 O-MUTE O MUTE output. 13 O-PB2 O DECK2/DECK1 play output. 14 O-BIAS O BIAS ON output. 15 O-RMT O REC mute output. 16 O-CD_ON O CD ON output. 17 IC Internal connection (connected to GND). 18 VSSO GND. 19 VDDO Power supply. 20 O-POWER O System power supply ON/OFF output. 21 O-OPEN O CD tray open data output. 22 O-CLOSE O CD tray close data output. 23 O-DISH_F O CD turntable forward rotation output. 24 O-DISH_R O CD turntable reverse rotation output. 25 NC Not connected. 26 NC Not connected. 27 I-REA I Volume jog AD input. 28 I-RDS_CLK I Tuner RDS clock input<22EZ>. 29 I-SUBQ/I-RDS_DATA I CD SUBQ data input / Tuner RDS data input<22EZ>. 30 RESET System reset. 31 O-DATA O Data output for MAIN. 32 I-WRQ/STEREO I CD WRQ input / Tuner stereo input. 33 I-DRF/IFC I CD DRF input / Tune IF count serial data input. 34 I-RMC I System remote control input. 35 I-DISHSENS I CD turntable photo sensor input. 36 O-CLK_SFT O Micon clock shift output. 37 VDD1 Power supply. 38 X2 4.19MHz oscillator circuit. 39 X1 4.19MHz oscillator circuit. 40 VSS1 GND. 41 AVDD Power supply. 42 I-HOLD I Power failure detected input. 43 I-CDSW I CD mecha switch input.
Pin Name I/O Description
– 22 –
Page 23
Pin No.
44 I-SPEANA_L I A/D L-input for spectrum analyser level display. 45 I-SPEANA_R I A/D R-input for spectrum analyser level display. 46 I-KEY1 I Key1 input. 47 I-KEY2 I Key2 input. 48 I-KEY3 I Key3 input. 49 I-TU_SIG I Tuner signal input. 50 AVSS GND. 51 O-PLL_CLK O PLL clock enable output. 52 O-PLL_CE O Chip enable output for tuner PLL. 53 O-CD_LED O CD flash window LED ON/OFF output. 54 O-KSCAN O Key scan output. 55 O-CD_CLK O CD clock output. 56 O-CD_DATA O CD data output. 57 O-CD_CE O CD enable output. 58 NC Not connected. 59 I-JOG_B I Dial jog rotary encoder input B. 60 I-JOG_A I Dial jog rotary encoder input A. 61 I-VOL_B I Volume rotary encoder input B. 62 I-VOL_A I Volume rotary encoder input A. 63 NC Not connected. 64 I-TM_BASE I Base input for clock. 65 I-CAM2 I DECK2 CAM switch data input. 66 I-CAM1 I DECK1 CAM STOP switch data input. 67 P1/I-AUTO2 O/I FL segment P1 output / DECK2 AUTO STOP switch data input. 68 P2/I-AUTO1 O/I FL segment P2 output / DECK1 AUTO STOP switch data input. 69 P3/I-CST2 O/I FL segment P3 output / DECK2 cassette detect switch data input. 70 P4/I-CST1 O/I FL segment P4 output / DECK1 cassette detect switch data input.
71, 72 P5, P6 O FL segment P5, P6 output.
73 P7/LW O/I FL segment P7 output / LW mode data input.
74, 75 P8, P9 O FL segment P8, P9 output.
76 P10/RDS O/I FL segment P10 output / RDS data input<22EZ>.
77, 78 P11, P12 O FL segment P11, P12 output.
79 VDD2 Power supply. 80 VLOAD Power supply for FL display. 81 P13/C-JACK O/I FL segment P13 output / C-JACK data input. 82 P14/ECO-OFF O/I FL segment P14 output / ECO-OFF data input.
83 ~ 90 P15 ~ P22 O FL segment P15 ~ P22 output.
91 ~100 G1 ~ G10 O FL grid G1 ~ G10 output.
Pin Name I/O Description
– 23 –
Page 24
ADJUSTMENT <TUNER / DECK / MICON>
A MAIN C.B
11
12
15
14
13
10
8
6
7
9
5
1
8
9
9
6
3
14
SFR 451
SFR 452
IC301
L801
TP8 (LCH)
GND
1
TP9 (RCH)
IC801
L802
1
24
TP2
(CLK)
TP4(DC BAL) TP3(DC BAL)
TP1(VT)
L942
(3/3)
TC942
L951
(1/3)
FFE801
L941
6
5
2 3 4
< TUNER SECTION >
1. Clock frequency Check Settings : • Test point : TP2 (CLK) Method : Set to MW 1602kHz and check that the test point is
2052kHz ± 45Hz.
2. MW VT Check Settings : • Test point : TP1 (VT) Method : Set to MW 1602kHz, 531kHz and check that the test
point is less than 8.0V (1602kHz) and more than
0.6V (531kHz).
3. LW VT Adjustment Settings : • Test point : TP1 (VT)
• Adjustment location : L942
Method : Set to LW 144kHz and adjust L942 so that the test point
becomes 1.3V ± 0.05V. Then set to LW 290kHz and check that the test point is less than 8.0V.
4. FM VT Check Settings : • Test point : TP1 (VT) Method : Set to FM 87.5MHz, 108.0MHz and check that the test
point is more than 0.5V (87.5MHz) and less than 8.0V (108.0MHz).
5. MW Tracking Adjustment Settings : • Test point : TP8(Lch), TP9(Rch)
• Adjustment location :
L951(1/3) ...................................... 1000kHz
Method : Set to MW 1000kHz and adjust L951(1/3) to MAX.
6. LW Tracking Adjustment Settings : • Test point : TP8 (Lch), TP9 (Rch)
• Adjustment location :
L941 ..........................................................144kHz
TC942 ........................................................290kHz
Method : Set up TC942 to center before adjustment.
Adjust L941 so that the level at 144kHz becomes maximum. Then adjust TC942 so that the level at 290kHz becomes maximum.
7. FM Tracking Check Settings : • Test point : TP8(Lch), TP9(Rch) Method : Set to FM 98.0MHz and check that the test point is less
than 13dBµV.
8. AM IF Adjustment Settings : • Test point : TP8(Lch), TP9(Rch)
• Adjustment location :
L802 ................................................450kHz
9. DC Balance / Mono Distortion Adjustment Settings : • Test point : TP3, TP4 (DC Balance)
TP8(Lch), TP9(Rch) (Distortion)
• Adjustment location : L801
• Input level : 60dBµV
Method : Set to FM 98.0MHz and adjust L801 so that the voltage
between TP3 and TP4 becomes 0V ± 0.04V. Next, check that the distortion is less than 1.3%.
– 24 –
Page 25
B FRONT C.B
D DECK C.B
14
TP11
D983
L951
FL901
IC901
0
3
+
C913
1
GND
DECK–1 P HEAD DECK–2 R/P/E HEAD
SFR1
10
< DECK SECTION >
10. Tape Speed Adjustment (DECK 2) Settings : • Test tape : TTA–100
• Test point : TP8(Lch), TP9(Rch)
• Adjustment location : SFR1
Method : Play back the test tape and adjust SFR1 so that the
frequency counter reads 3000Hz ± 5Hz and ± 45Hz (REV) with respect to forward speed.
11. Head Azimuth Adjustment (DECK 1, DECK 2) Settings : • Test tape : TTA–330
• Test point : TP8(Lch), TP9(Rch)
• Adjustment location :Azimuth adjustment screw
Method : Play back (FWD) the 8kHz signal of the test tape and
adjust screw so that the output becomes maximum. Next, perform on REV PLAY mode.
12. PB Frequency Response Check (DECK 1, DECK 2) Settings : • Test tape : TTA–330
• Test point :TP8(Lch), TP9(Rch)
Method : Play back the 315Hz and 8kHz signals of the test tape
and check that the output ratio of the 8kHz signal with respect to that of the 315Hz signal is within 5dB.
13. PB Sensitivity Check (DECK 1, DECK 2) Settings : • Test tape : TTA–200
• Test point : TP8(Lch), TP9(Rch)
Method : Play back the test tape and check that the output level of
the test point is 110mV ± 3dB.
FWD
11
REV
11
14. REC/PB Frequency Response Adjustment (DECK 2) Settings : • Test tape : TTA–602
• Test point : TP8(Lch), TP9(Rch)
• Input signal : 1kHz / 8kHz (LINE IN)
• Adjustment location : SFR451 (Lch) SFR452 (Rch)
Method : Apply a 1kHz signal and REC mode. Then adjust OSC
attenuator so that the output level at the TP8, TP9 becomes -20VU (-26dBV). Record and play back the 1kHz and 8kHz signals and adjust SFRs so that the output of the 8kHz signals becomes 0dB ± 0.5dB with respect to that of the 1kHz signal.
15. REC/PB Sensitivity Check (DECK 2) Settings : • Test tape : TTA–602
• Test point : TP8(Lch), TP9(Rch)
• Input signal : 1kHz (LINE IN)
Method : Apply a 1kHz signal and REC mode. Then adjust OSC
attenuator so that the output level at TP8, TP9 becomes 0VU (-6dBV). Record and play back the 1kHz signals and check that the output is -1dB ± 3.5dB.
16. µ-con OSC Adjustment Settings : • Test point : TP11,GND
• Adjustment location : L951
Method : Insert AC plug while pressing TUNER function key.
Adjust L951 so that the frequency across the test point becomes 184.98Hz ± 0.18Hz.
– 25 –
Page 26
MECHANICAL EXPLODED VIEW 1 / 1
G
15
17
AZG-1 ZD8RDM<EZ> AZG-1 YZD8RDM<K>
A
A
19
B
20
18
30
31
21
A
FL901
22
24
16
I
23
29
25
A
A
HT-SINK
C
P.C.B
WIRE,BINDER
32
A
A
A
33
A
G
12
H
45
A
A
44
9
E
5
11
3
1
2
7
I
27
PLATE,EARTH MIC
9
6
36
37
13
8
4
14
D
PLATE,EARTH MECH
10
34
26
38
38
37
35
39
P.C.B
F
A
A
ZZM-3 PR1NM<EZ> ZZM-3 YPR1NF<K>
H
A
CHAS,MAIN
40
28
PT
41
A
42
43
G
– 26 –
Page 27
MECHANICAL PART LIST 1 / 1
PART NO.
NO.
1 8A-NF9-006-010 WINDOW,CASS 1<EXCEPT 27> 1 8A-NF9-085-010 WINDOW,CASS 1 B<27> 2 8A-NF9-007-010 WINDOW,CASS 2<EXCEPT 27> 2 8A-NF9-086-010 WINDOW,CASS 2 B<27> 3 8A-NF9-003-010 BOX,CASS 1<EXCEPT 27>
3 8A-NF9-082-010 BOX,CASS 1 B<27> 4 8A-NF9-004-010 BOX,CASS 2<EXCEPT 27> 4 8A-NF9-083-010 BOX,CASS 2 B<27> 5 8A-NF8-207-010 SPR-T,EJECT 1 6 8A-NF8-208-010 SPR-T,EJECT 2
7 87-CE3-023-010 BADGE,AIWA 30N SILV 8 8A-NF9-018-010 KNOB,RTRY JOG 9 8A-NF8-209-010 OIL-DMPR,120 10 8A-NF9-017-010 PANEL,JOG 11 8A-NF9-016-010 KNOB,RTRY VOL
12 8A-NF9-211-010 HLDR,PWB PT HI 13 81-532-080-010 LABEL, CASS. COMPT 14 8A-NF9-049-010 CABI,FR EZ R<22> 14 8A-NF9-081-010 CABI,FR EZB<27> 14 8A-NF9-001-010 CABI,FR U<20>
15 8A-NF9-044-010 WINDOW,DISP EZ RDS<22> 15 8A-NF9-084-010 WINDOW,DISP EZB Z27<27> 15 8A-NF9-052-010 WINDOW,DISP LH<20EZ> 15 8A-NF9-005-010 WINDOW,DISP U<20K> 16 8A-NF9-039-010 WINDOW,CD<EXCEPT 27>
16 8A-NF9-089-010 WINDOW,CD B<27> 17 8A-NF8-007-010 PANEL,LEFT V-2<EXCEPT 27> 17 8A-NF9-092-010 PANEL,LEFT V-2 B<27> 18 8A-NF8-005-010 PANEL,TOP<EXCEPT 27> 18 8A-NF9-090-010 PANEL,TOP B<27>
19 8A-NF8-006-010 WINDOW,TOP<EXCEPT 27> 19 8A-NF9-091-010 WINDOW,TOP B<27> 20 8A-NF9-014-010 PANEL,TRAY<EXCEPT 27> 20 8A-NF9-088-010 PANEL,TRAY B<27> 21 8A-NF9-008-010 KEY,POWER<EXCEPT 27>
21 8A-NF9-087-010 KEY,POWER B<27> 22 8A-NF9-009-010 KEY,FUN 23 8A-NF9-022-010 REFLECTOR,ECO 24 8A-NF9-010-110 KEY,ASSY OPE 1 WAY 25 8A-NF9-020-010 KEY,CD
DESCRIPTIONREF. NO. KANRI
PART NO.
26 8A-NF9-050-010 KEY,RDS<22> 26 8A-NF9-019-010 KEY,SYNC<EXCEPT 22> 27 8A-NF9-026-110 KEY,ENTER 28 87-A80-157-010 AC CORD ASSY,E BLK CC
!
29 8A-NF9-201-010 GUIDE,OPE 1 WAY
30 82-NF7-210-110 GUIDE,FL (*) 31 8A-NF8-206-010 HLDR,PWB M 32 88-906-251-110 FF-CABLE,6P 1.25 33 8A-NF8-205-010 HLDR,IC 34 88-913-301-110 FF-CABLE,13P-1.25
35 88-911-101-110 FF-CABLE,11P 1.25 36 87-NF4-216-010 HLDR,LOCK 1 37 86-NF9-224-010 SPR-C,LOCK 38 82-NF5-229-010 PLATE,LOCK 39 87-NF4-217-110 HLDR,LOCK 2
40 87-NF4-221-010 HLDR,CABLE 41 87-085-185-010 BUSHING, AC CORD (E) 42 8Z-NB8-240-010 COVER, PL 43 8A-NF8-008-010 PANEL,RIGHT V-2<EXCEPT 27> 43 8A-NF9-093-010 PANEL,RIGHT V-2 B<27>
44 8A-NF9-094-010 CABI,REAR EZBM<27> 44 8A-NF9-059-110 CABI,REAR EZSM<20EZ> 44 8A-NF9-058-110 CABI,REAR EZSM R<22> 44 8A-NF9-035-010 CABI,REAR KSE<20K> 45 84-ZG1-245-210 CAP,OPTICAL
A 87-067-703-010 TAPPING SCREW, BVT2+3-10 B 87-NF4-224-010 S-SCREW,IT3B+3-8 CU C 87-067-581-010 TAPPING SCREW, BVT2+3-15 D 87-067-689-010 TAPPING SCREW, BVTT+3-8 E 87-723-096-410 QT2+3-10W/O SLOT BL
F 87-721-096-410 QT2+3-10 GLD G 87-067-641-010 UTT2+3-8(W/O SLOT)BL H 87-078-191-010 S-SCREW,IT+4-10 I 87-721-097-410 QT2+3-12 GLD
NO.
DESCRIPTIONREF. NO. KANRI
COLOR NAME TABLE
Basic color symbol Color Basic color symbol Color Basic color symbol Color
B Black C Cream D Orange
G Green H Gray L Blue
LT Transparent Blue N Gold P Pink
R Red S Silver ST Titan Silver T Brown V Violet W White
WT Transparent White Y Yellow YT Transparent Yellow
LM Metallic Blue LL Light Blue GT Transparent Green LD Dark Blue DT Transparent Orange GM Metallic Green
YM Metallic Yellow DM Metallic Orange
– 27 –
Page 28
TAPE MECHANISM EXPLODED VIEW 1 / 1
TERMINAL, LB1
33
31
AA
34
32
30 21
20
19
55
35
28
27
26
25 24
29
37
39
38
36
41
40
43 42
44
52
33
31
21
20
41
44
45
46
51
b
53
47
48
49
50
52
51
43
42
40
b
45
46 47
a
a
48
49
B
A
TERMINAL,LB1
32
35
30
29
28
27
26
25
23
18
22
5
6
14
10
11
7
15
16
9
1
2
6
10
7
11
8
5
3
c
14
9
56
16
19
IC, EW732
18
54
38
39
37
P.C.B
12
24
23
22
IC, EW732
54
c
17
12
13
4
– 28 –
15
13
Page 29
TAPE MECHANISM PART LIST 1 / 1
PART NO.
NO.
1 8Z-ZM3-227-010 0E BELT,MAIN M3 2 8Z-ZM3-235-010 0E BELT,MAIN L 3 8Z-ZM1-235-010 0E PULLEY,MOT 4 87-045-347-010 1H MOT,SHU2L 70 5 8Z-ZM1-232-010 0E GEAR,IDL FF/REW
6 8Z-ZM3-244-010 0E GEAR,CAM TD20 7 8Z-ZM3-242-010 0E SHAFT,CAP M3 8 8Z-ZM3-228-010 0E FLY-WHL,M3 9 8Z-ZM3-231-010 0E SPR-T,TRIG 10 8Z-ZM3-213-010 0E CLR,MG
11 82-ZM3-616-010 0E RING MAGNET 4 12 8Z-ZM3-243-010 0E LEVER ASSY,HD UP 13 8Z-ZM3-238-010 0E SPR-T,HD UP 14 8Z-ZM3-219-010 0E GEAR,CAM M3 15 8Z-ZM3-206-010 0E LEVER,TRIG
16 8Z-ZM3-209-010 0E LEVER,CAM FR 17 8Z-ZM2-211-010 0E FLY-WHL,ZZM-2 18 8Z-ZM1-228-010 0E GEAR,SLIP T-UP B 19 8Z-ZM1-265-010 0E FELT,T-UP 20 8Z-ZM1-227-010 0E GEAR,SLIP T-UP A
21 8Z-ZM1-251-110 0E SPR-C,T-UP SLIP 22 8Z-ZM1-275-010 0E W-L,1,47-4-0.25 23 8Z-ZM1-257-010 0E SPR-C,F/R 24 8Z-ZM1-236-010 0E CLR,SLIP FF/REW 25 8Z-ZM3-226-010 0E SPR-C,FR M3
26 8Z-ZM3-250-010 0E GEAR,SLIP F/R A M3 27 8Z-ZM1-269-010 0E FELT,FF/REW 2 28 8Z-ZM1-238-110 0E GEAR,SLIP FF/REW B 2 29 8Z-ZM3-220-010 0E LEVER,FR M3 30 8Z-ZM3-205-010 0E LEVER,PLAY M3
DESCRIPTIONREF. NO. KANRI
PART NO.
NO.
31 8Z-ZM3-233-010 0E SPR-T,BRG M3 32 84-ZM2-227-310 0E SPR-C,AZIMUTH 33 87-A90-403-110 1B HEAD,RPH MS15R 34 87-A90-404-010 1B HEAD,EH LE15B 35 8Z-ZM3-239-010 0E SPR-E,FR
36 8Z-ZM3-211-010 0E LEVER,EJECT R 37 8Z-ZM3-225-010 0E LEVER,STOP 38 8Z-ZM3-221-010 0E LEVER,CAS 39 8Z-ZM3-234-010 0E SPR-T,LVR CAS 40 8Z-ZM3-223-010 0E SPR-C,REEL R M3
41 8Z-ZM1-225-110 0E GEAR,REEL R 42 8Z-ZM3-240-010 0E SPR-T,T-UP M3 43 8Z-ZM3-237-010 0E SPR-T,PINCH M3 44 8Z-ZM3-215-010 0E LEVER,PINCH M3 45 8Z-ZM1-261-110 0E ROLLER ASSY,PINCH
46 8Z-ZM1-226-010 0E GEAR,REEL L 47 8Z-ZM3-222-010 0E SPR-C,REEL L M3 48 8Z-ZM3-251-010 0E GEAR,IDL REW M3 49 8Z-ZM3-236-010 0E SPR-T,PLAY M3 50 82-ZM1-240-110 0E LVR,REC(*)
51 8Z-ZM3-216-010 0E LEVER,T-UP M3 52 87-B10-301-010 0E W-L,1.63-3.2-05 SLIT 53 8Z-ZM3-212-010 0E LEVER,EJECT L 54 8Z-ZM3-214-010 0E HLDR,IC 55 86-ZM3-605-110 1B CONN ASSY,8P -RPB
56 8Z-ZM3-203-010 1H CHAS ASSY,M3 A 84-ZM2-242-010 0E S-SCREW,AZ1-2-6.4 B 8Z-ZM2-220-110 0E V+2.6 ZZM-2
DESCRIPTIONREF. NO. KANRI
– 29 –
Page 30
SPEAKER DISASSEMBLY INSTRUCTIONS
Type.1
Insert a flat-bladed screwdriver into the position indicated by the arrows and remove the panel. Remove the screws of each speaker unit and then remove the speaker units.
Type.2
Remove the grill frame and four pieces of rubber caps by pulling out with a flat-bladed screwdriver. Remove the screws from hole where installed rubber caps. Insert a flat-bladed screwdriver into the position indicated by the arrows and remove the panel. Re­move the screws of each speaker unit and then remove the speaker units.
Type.4
TOOLS
1 Plastic head hammer 2 flat head screwdriver 3 Cut chisel
123
How to Remove the PANEL, FR
1. Insert the flat head screwdriver tip into the gap between
the PANEL, FR and the PANEL, SPKR. Tap the head of the flat head screwdriver with the plastic and create the clearance as shown in Fig-1.
2. Insert the cut chisel in the clearance, and tap the head of
the cut chisel with plastic hammer as shown in Fig-2, to remove the PANEL, FR.
hammer head,
Type.3
Insert a flat-bladed screwdriver into the position indicated by the arrows and remove the panel. Turn the speaker unit to counter­clockwise direction while inserting a flat-bladed screwdriver into one of the hollows around speaker unit, and then remove the speaker unit. After replacing the speaker unit, install it turning to clockwise direction until "click" sound comes out.
3. Place the speaker horizontally. Tap head of the cut chisel
with plastic hammer as shown in Fig-3, and remove the PANEL, FR completely.
Fig-1 Fig-2
How to Attach the PANEL, FR
Attach the PANEL, FR to the PANEL, SPKR. Tap the four corners of the PANEL, FR with the plastic hammer to fit the PANEL, FR into the PANEL, SPKR completely.
– 30 –
Fig-3
Page 31
SPEAKER PARTS LIST SX-NSZ20 (YBC9,YBY1,YBY2,YSL,YSC9,YSY1,YSY2), SX-NSZ22 (YSC9,YSY1,YSY2)
PART NO.
NO.
1 8A-NSK-001-010 PANEL,FR<EXCEPT YBC9,YBY1,YBY2> 2 8A-NSK-003-010 GRILLE,FRAME ASSY 3 8A-NSK-007-010 PROTECTOR,TWA 4 8A-NSK-602-010 SPKR,W 140<EXCEPT 22YSC9> 4 8A-NSJ-602-010 SPKR,W 130<22YSC9>
5 88-NS5-605-010 SPKR,T 60<EXCEPT 22YSC9> 5 8A-NSK-604-010 SPKR,TW 60<22YSC9> 6 87-NSH-612-010 SPKR,CERAMIC ASSY 7 87-NS7-611-010 CORD,SPKR
DESCRIPTIONREF. NO. KANRI
ACCESSORIES / PACKAGE LIST
PART NO.
NO.
1 8A-NF9-926-010 IB,EZ(9L)M<20EZ,27EZ> 1 8A-NF9-927-010 IB,EZ(9L)M SZ22(RDS)<22EZ> 1 8A-NF9-905-010 IB,K(E)E<20K> 2 87-A90-118-010 ANT,WIRE FM(Z) 3 87-006-225-010 AM,LOOP ANT NC2
4 8Z-NF9-701-210 RC UNIT,ZAS02<20EZ,20K,22EZ> 4 8Z-NF9-703-110 RC UNIT,ZAS17<27EZ>
DESCRIPTIONREF. NO. KANRI
– 31 –
Page 32
2–11, IKENOHATA 1–CHOME, TAITO-KU, TOKYO 110, JAPAN TEL:03 (3827) 3111
Printed in Singapore9820543 0251431
Loading...