Total harmonic distortion0.2 % (8 W, 1 kHz, 8 ohms,
DIN AUDIO)
InputsVIDEO/AUX: 300 mV (adjustable)
MD: 300 mV (adjustable)
MIC 1, MIC 2: 1.0 mV (10 kohms)
OutputsSPEAKERS: 6 ohms or more
SATELLITE SPEAKERS:
8 ohms or more
LINE OUT: 210 mV
CD DIGITAL OUT (OPTICAL)
PHONES: 32 ohms or more
<CD player section>
LaserSemiconductor laser (λ = 780 nm)
D-A converter1 bit dual
Signal-to-noise ratio85 dB (1 kHz, 0 dB)
Harmonic distortion0.05 % (1 kHz, 0 dB)
<General>
Power requirements120 V/ 220 V – 230 V/ 240 V AC
(switchable) 50/60 Hz
Power consumption250 W
Power consumptionWith ECO mode on: 0.6 W
in standby modeWith ECO mode off: 40 W
Dimensions (W x H x D)260 x 326 x 394 mm
Weight10.5 kg
Full range: 100 mm cone type
Super tweeter: 20 mm ceramic type x 2
Impedance6 ohms
Dimensions (W x H x D)240 x 324 x 294 mm
Weight5.4 kg
<Satellite speakers SX-S85>
Speaker systemFull range (magnetic shielded type)
Speaker units80 mm cone type
Impedance8 ohms
Sensitivity87 dB/W/m
Dimensions (W x H x D)100 x 325 x 95 mm (with pedestal)
• Design and specifications are subject to change without
notice.
• The word “BBE” and the “BBE symbol” are trademarks of BBE
Sound, Inc.
Under license from BBE Sound, Inc.
– 2 –
PROTECTION OF EYES FROM LASER BEAM DURING SERVICING
This set employs laser. Therefore, be sure to follow carefully
the instructions below when servicing.
WARNING!!
WHEN SERVICING, DO NOT APPROACH THE LASER
EXIT WITH THE EYE TOO CLOSELY. IN CASE IT IS
NECESSARY TO CONFIRM LASER BEAM EMISSION.
BE SURE TO OBSERVE FROM A DISTANCE OF MORE
THAN 30cm FROM THE SURFACE OF THE OBJECTIVE LENS ON THE OPTICAL PICK-UP BLOCK.
s Caution: Invisible laser radiation when
open and interlocks defeated avoid
exposure to beam.
s Advarsel: Usynlig laserståling ved åbning,
når sikkerhedsafbrydere er ude af funktion.
Undgå udsættelse for stråling.
VAROITUS!
Laiteen Käyttäminen muulla kuin tässä käyttöohjeessa
mainitulla tavalla saataa altistaa käyt-täjän
turvallisuusluokan 1 ylittävälle näkymättömälle
lasersäteilylle.
VARNING!
Om apparaten används på annat sätt än vad som
specificeras i denna bruksanvising, kan användaren
utsättas för osynling laserstrålning, som överskrider
gränsen för laserklass 1.
CAUTION
Use of controls or adjustments or performance of procedures other than those specified herin may result in
hazardous radiation exposure.
ATTENTION
L’utillisation de commandes, réglages ou procédures
autres que ceux spécifiés peut entraîner une dangereuse
exposition aux radiations.
ADVARSEL
Usynlig laserståling ved åbning, når sikkerhedsafbrydereer
ude af funktion. Undgå udsættelse for stråling.
This Compact Disc player is classified as a CLASS 1
LASER product.
The CLASS 1 LASER PRODUCT label is located on the
rear exterior.
CLASS 1LASER PRODUCT
KLASSE 1LASER PRODUKT
LUOKAN 1LASER LAITE
KLASS 1LASER APPARAT
Precaution to replace Optical block
(KSS-213F)
Body or clothes electrostatic potential could
ruin laser diode in the optical block. Be sure
ground body and workbench, and use care the
clothes do not touch the diode.
1) After the connection, remove solder shown in
right figure.
PICK-UP Assy PWB
Solder
– 3 –
NOTE ON BEFORE STARTING REPAIR
1. Forced discharge of electrolytic capacitor of power supply block
When repair is going to be attempted in the set that uses relay circuit in the power supply block, electric potential is kept charged across
the electrolytic capacitors (C101, 102) even though AC power cord is removed. If repair is attempted in this condition, secondary defect
can occur.
In order to prevent the secondary trouble, perform the following measures before starting repair work.
Discharge procedure
11
1 Remove the AC power cord.
11
22
2 Connect a discharging resistor at an end of lead wire that
22
has clips at both ends. Connect the other end of the lead
wire to metal chassis.
33
3 Contact the other end of the discharging resistor to the
33
positive (+) side (+VH) of C101. (For two seconds)
44
4 Contact the same end of the discharging resistor as step
44
33
3 to the negative (-) side (-VH) of C102 in the same way.
33
(For two seconds)
55
5 Check that voltage across C101 and C102 has decreased
55
to 1 V or less using a multimeter or an oscilloscope.
Select a discharging resistor referring to the following table.
Charging voltage (V)Discharging
(C101, 102)resistor (Ω)
25-48100387-A00-247-090
49-140220587-A00-232-090
Note: The reference numbers (C101, C102) of the electrolytic capacitors can change depending on the models. Be sure to check the
reference numbers of the charging capacitors on schematic diagram before starting the discharging work.
Rated power (W)Parts number
MAIN C.B
D101
3
C101C102
22
Fig-1
4
2. Check items before exchanging the MICROCOMPUTER
Be sure to check the following items before exchanging the MICROCOMPUTER. Exchange the MICROCOMPUTER after confirming
that the MICROCOMPUTER is surely defective.
2-1. Regarding the HOLD terminal of the MICROCOMPUTER
When the HOLD terminal (INPUT) of the MICROCOMPUTER is “H”, the MICROCOMPUTER is judged to be operating correctly.
When this terminal is “L”, the main power cannot be turned on. Therefore, be sure to check the terminal voltage of the HOLD
terminal before exchange.
When the MICROCOMPUTER is not defective, the HOLD terminal can also go “L” when the POWER AMPLIFIER has any
abnormalities that triggers the abnormality detection circuit on the MAIN C. B. that sets the HOLD terminal to “L”.
• Good or no good judgement of the MICROCOMPUTER
11
1 Turn on the AC main power.
11
22
2 Confirm that the main power is turned on and the HOLD terminal of the MICROCOMPUTER keeps the “H” level or not.
22
33
3 When the HOLD terminal is “L” level, the abnormality detection circuit is judged to be working correctly and the
33
MICROCOMPUTER is judged to be good.
– 4 –
In such a case, check also if the POWER AMPLIFIER circuit or power supply circuit has any abnormalities or not.
2-2. Regarding reset
There are cases that the machine does not work correctly because the MICROCOMPUTER is not reset even though the AC power
cord is re-inserted, or the software reset (pressing the STOP key + POWER key) is performed.
When the above described phenomenon occurs, it can lead to wrong judgement as if the MICROCOMPUTER is defective and to
exchange the MICROCOMPUTER. In such a case, perform the forced-reset by the following procedure and check good or no
good of the MICROCOMPUTER.
11
1 Remove the AC power cord.
11
FRONT C.B
18
MICROCOMPUTER
FRONT C.B
22
2 Short both ends of the electrolytic capacitor C113 that is connected to VDD of the MICROCOMPUTER with tweezers.
22
33
3 Connect the AC power cord again. If the MICROCOMPUTER returns to the normal operation, the MICROCOMPUTER is
33
good.
Note: The reference number or MICROCOMPUTER pin number of transistor (Q110) and electrolytic capacitor (C113) can change depending
on the models. Be sure to check the reference numbers on schematic diagram before starting the discharging work.
15
C113
Short with tweezers.
Fig-2-2
C113
%
*
VSS
VDD
MICROCOMPUTER
2-3. Confirmation of soldering state of MICROCOMPUTER
Check the soldering state of the MICROCOMPUTER in addition to the above described procedures. Be sure to exchange the
MICROCOMPUTER after surely confirming that the trouble is not caused by poor soldering but the MICROCOMPUTER itself.
87-A40-781-080 ZENER,UZ36BSA
87-A40-553-080 DIODE,1N4003 LES
87-A40-745-080 ZENER,UZ4.7BSA
87-A40-530-080 DIODE,RB721Q-40
MAIN C.B
DESCRIPTIONREF. NO.KANRI
PART NO.
NO.
C11 87-012-368-080 C-CAP,S 0.1-50 Z F
C12 87-012-368-080 C-CAP,S 0.1-50 Z F
C13 87-012-368-080 C-CAP,S 0.1-50 Z F
C14 87-012-368-080 C-CAP,S 0.1-50 Z F
C20 87-010-918-090 CAP,E 4700-50 SMG
C21 87-A12-780-090 CAP,E 4700-35 M 85 SKR
C23 87-A10-231-090 CAP,E 3300-80
C24 87-A10-231-090 CAP,E 3300-80
C31 87-A12-062-080 CAP,E 100-10 SMG
C32 87-012-286-080 C-CAP,U 0.01-25 K B
C38 87-A12-092-080 CAP,E 22-50 SMG
C39 87-A12-067-080 CAP,E 330-16 SMG
C40 87-A12-074-080 CAP,E 470-25 SMG
C101 87-012-276-080 C-CAP,U 1500P-50 K B
C102 87-012-276-080 C-CAP,U 1500P-50 K B
C103 87-012-368-080 C-CAP,S 0.1-50 Z F
C104 87-012-368-080 C-CAP,S 0.1-50 Z F
C105 87-012-368-080 C-CAP,S 0.1-50 Z F
C106 87-012-368-080 C-CAP,S 0.1-50 Z F
C123 87-010-759-080 C-CAP,U 0.1-25 Z F
C124 87-010-759-080 C-CAP,U 0.1-25 Z F
C125 87-010-759-080 C-CAP,U 0.1-25 Z F
C126 87-010-759-080 C-CAP,U 0.1-25 Z F
C130 87-012-274-080 C-CAP,U 1000P-50 K B
C131 87-A12-087-080 CAP,E 1-50 SMG
C304 87-012-336-080 C-CAP,U 330P-50 J SL
C305 87-012-336-080 C-CAP,U 330P-50 J SL
C306 87-012-336-080 C-CAP,U 330P-50 J SL
C307 87-A10-262-080 C-CAP,U 1-10 Z F
C309 87-A10-260-080 C-CAP,U 0.1-16 K B
C310 87-A10-260-080 C-CAP,U 0.1-16 K B
C311 87-010-787-080 CAP,U 0.022-25 K B
C312 87-010-787-080 CAP,U 0.022-25 K B
C313 87-012-277-080 C-CAP,U 1800P-50 K B GRM
C314 87-012-277-080 C-CAP,U 1800P-50 K B GRM
C315 87-012-275-080 C-CAP,U 1200P-50 K B GRM
C316 87-012-275-080 C-CAP,U 1200P-50 K B GRM
C321 87-A10-828-080 C-CAP,U 0.33-6.3 K B
C322 87-A10-828-080 C-CAP,U 0.33-6.3 K B
C324 87-A12-071-080 CAP,E 47-25 SMG
C336 87-A12-087-080 CAP,E 1-50 SMG
C337 87-010-831-080 C-CAP,U 0.1-16 Z F
C339 87-010-831-080 C-CAP,U 0.1-16 Z F
C340 87-010-831-080 C-CAP,U 0.1-16 Z F
C351 87-A10-039-080 C-CAP,U 470P-50 J CH
C358 87-012-279-080 C-CAP,U 2700P-50 B
C359 87-012-279-080 C-CAP,U 2700P-50 B
C360 87-012-279-080 C-CAP,U 2700P-50 B
C363 87-A12-361-080 CAP,M 5600P-100 J CP
C370 87-010-831-080 C-CAP,U 0.1-16 Z F
DESCRIPTIONREF. NO.KANRI
– 6 –
PART NO.
NO.
C373 87-A10-794-080 C-CAP,U 0.15-16 Z F
C374 87-A10-794-080 C-CAP,U 0.15-16 Z F
C378 87-010-831-080 C-CAP,U 0.1-16 Z F
C379 87-A12-069-080 CAP,E 22-25 SMG
C380 87-A12-069-080 CAP,E 22-25 SMG
C532 87-010-831-080 C-CAP,U 0.1-16 Z F
C533 87-010-831-080 C-CAP,U 0.1-16 Z F
C534 87-012-199-080 C-CAP,U 220P-50 J CH
C535 87-012-274-080 C-CAP,U 1000P-50 K B
C536 87-010-831-080 C-CAP,U 0.1-16 Z F
C537 87-012-188-080 C-CAP,U 47P-50 CH
C538 87-012-188-080 C-CAP,U 47P-50 CH
C539 87-012-188-080 C-CAP,U 47P-50 CH
C541 87-012-274-080 C-CAP,U 1000P-50 K B
C609 87-012-277-080 C-CAP,U 1800P-50 B
C610 87-012-277-080 C-CAP,U 1800P-50 B
C611 87-010-956-080 C-CAP,S 0.068-25B
C612 87-A11-070-080 C-CAP,U 0.033-16 K B
C613 87-012-286-080 C-CAP,U 0.01-25
C614 87-012-286-080 C-CAP,U 0.01-25
C615 87-A10-260-080 C-CAP,U 0.1-16 K B
C616 87-A10-260-080 C-CAP,U 0.1-16 K B
C617 87-010-829-080 C-CAP,U 0.047-16
C618 87-A12-087-080 CAP,E 1-50 SMG
C619 87-A12-062-080 CAP,E 100-10 SMG
C628 87-A12-086-080 CAP,E 0.47-50 SMG
C629 87-A10-504-080 C-CAP,U 0.047-16 K B
C630 87-A10-504-080 C-CAP,U 0.047-16 K B
C631 87-012-281-080 C-CAP,U 3900P-50 B
C632 87-012-281-080 C-CAP,U 3900P-50 B
C633 87-010-831-080 C-CAP,U 0.1-16 Z F
C634 87-010-831-080 C-CAP,U 0.1-16 Z F
C635 87-A12-376-080 CAP,M 0.1-100 J CP
C636 87-A12-376-080 CAP,M 0.1-100 J CP
C637 87-A12-376-080 CAP,M 0.1-100 J CP
C113 87-010-788-080 C-CAP,U 0.33-25 Z F
C201 87-016-083-080 C-CAP,S 0.15-16 K R
C202 87-012-270-080 CAP,U 470P-50 K B
C207 87-010-590-080 C-CAP,S 0.015-16 K R
C301 87-012-180-080 C-CAP,U 22P-50 J CH
C355 87-012-188-080 C-CAP,U 47P-50 J CH
C383 87-010-759-080 C-CAP,U 0.1-25 Z F
C384 87-010-759-080 C-CAP,U 0.1-25 Z F
C385 87-010-759-080 C-CAP,U 0.1-25 Z F
C386 87-010-759-080 C-CAP,U 0.1-25 Z F
C387 87-010-759-080 C-CAP,U 0.1-25 Z F
C601 87-012-282-080 CAP,U 4700P-50 K B
C602 87-010-405-040 CAP,E 10-50 M 11L SME
C605 87-A12-317-080 C-CAP,U 0.1-50 Z F
C606 87-010-112-040 CAP,E 100-16 M 11L SME
C607 87-010-759-080 C-CAP,U 0.1-25 Z F
C611 87-012-274-080 C-CAP,U 1000P-50 K B
C612 87-010-546-040 CAP,E 0.33-50 M 11L SME
C613 87-012-191-080 C-CAP,U 68P-50 J CH
C614 87-012-274-080 C-CAP,U 1000P-50 K B
C652 87-012-279-080 C-CAP,U 2700P-50 K B GRM
C653 87-010-785-080 C-CAP,U 0.015-25 K B GRM
C701 87-010-406-040 CAP,E 22-50 M 11L SME
C901 87-010-759-080 C-CAP,U 0.1-25 Z F
C902 87-012-335-080 C-CAP,U 270P-50 J SL
C903 87-012-195-080 C-CAP,U 100P-50 J CH
C904 87-010-596-080 C-CAP,S 0.047-16 K R C2012
C905 87-012-176-080 C-CAP,U 15P-50 J CH
C906 87-A10-189-040 CAP,E 220-10 M 5L
C908 87-012-274-080 C-CAP,U 1000P-50 K B
C909 87-012-286-080 C-CAP,U 0.01-25 K B
C910 87-012-270-080 C-CAP,U 470P-50 K B
C911 87-012-199-080 C-CAP,U 220P-50 J CH
C912 87-012-199-080 C-CAP,U 220P-50 J CH
C913 87-012-199-080 C-CAP,U 220P-50 J CH
C921 87-012-270-080 C-CAP,U 470P-50 K B
C923 87-010-759-080 C-CAP,U 0.1-25 Z F
C925 87-A12-317-080 C-CAP,U 0.1-50 Z F
C926 87-010-759-080 C-CAP,U 0.1-25 Z F
C927 87-010-759-080 C-CAP,U 0.1-25 Z F
C928 87-010-408-040 CAP,E 47-50 M 11L SME
C929 87-012-369-080 C-CAP,S 0.047-50 Z F
C931 87-010-404-040 CAP,E 4.7-50 M 11L SME
C933 87-010-404-040 CAP,E 4.7-50 M 11L SME
C991 87-010-405-040 CAP,E 10-50 M 11L SME
C992 87-012-336-080 C-CAP,U 330P-50 J SL
CN101 87-099-720-010 CONN,30P BLK TYK-B(P)
CN104 87-099-017-010 CONN,15P V BLK 6216
CN151 87-099-196-010 CONN,8P V BLK 6216
CN801 87-099-212-010 CONN,5P V BLK 6216
C577 87-012-188-080 C-CAP,U 47P-50 J CH
C581 87-012-274-080 C-CAP,U 1000P-50 K B
C582 87-012-195-080 C-CAP,U 100P-50 J CH
C583 87-012-195-080 C-CAP,U 100P-50 J CH
C591 87-012-274-080 C-CAP,U 1000P-50 K B
DESCRIPTIONREF. NO.KANRI
PART NO.
NO.
C592 87-012-195-080 C-CAP,U 100P-50 J CH
C593 87-012-195-080 C-CAP,U 100P-50 J CH
C802 87-012-197-080 C-CAP,U 150P-50 J CH
C804 87-012-283-080 C-CAP,U 5600P-50 K B
C805 87-010-831-080 C-CAP,U 0.1-16 Z F
C806 87-010-401-040 CAP,E 1-50 M 11L SME
C808 87-010-831-080 C-CAP,U 0.1-16 Z F
C809 87-012-198-080 C-CAP,U 180P-50 J CH
C810 87-010-263-040 CAP,E 100-10 M 11L SME
C811 87-010-545-040 CAP,E 0.22-50 M 11L SME
C812 87-010-405-040 CAP,E 10-50 M 11L SME
CN501 8B-NF6-606-010 CONN ASSY,6P DADA
CN502 8B-NF6-607-010 CONN ASSY,7P DADA
CN503 8B-NF6-606-010 CONN ASSY,6P DADA
CN802 87-099-212-010 CONN,5P V BLK 6216
C1 87-010-759-080 C-CAP,U 0.1-25 Z F
C2 87-010-759-080 C-CAP,U 0.1-25 Z F
C3 87-010-759-080 C-CAP,U 0.1-25 Z F
C4 87-010-759-080 C-CAP,U 0.1-25 Z F
C15 87-010-759-080 C-CAP,U 0.1-25 Z F
C17 87-016-299-080 CAP,E 10-100 M SME
C18 87-010-866-080 CAP,E 10-63 M VX
C101 87-012-276-080 C-CAP,U 1500P-50 K B
C102 87-012-276-080 C-CAP,U 1500P-50 K B
C103 87-A12-085-080 CAP,E 0.33-50 SMG
C104 87-A12-085-080 CAP,E 0.33-50 SMG
C105 87-012-279-080 C-CAP,U 2700P-50 K B GRM
C106 87-012-279-080 C-CAP,U 2700P-50 K B GRM
C107 87-A12-090-080 CAP,E 4.7-50 SMG
C108 87-A12-090-080 CAP,E 4.7-50 SMG
C118 87-A10-596-080 C-CAP,S 100P-100 J CH
C119 87-012-368-080 C-CAP,S 0.1-50 Z F
C120 87-012-368-080 C-CAP,S 0.1-50 Z F
C121 87-A10-596-080 C-CAP,S 100P-100 J CH
C122 87-A10-596-080 C-CAP,S 100P-100 J CH
C141 87-012-282-080 C-CAP,U 4700P-50 K B
C142 87-012-278-080 C-CAP,U 2200P-50 K B
C151 87-012-286-080 C-CAP,U 0.01-25 K B
C152 87-012-286-080 C-CAP,U 0.01-25 K B
C161 87-010-759-080 C-CAP,U 0.1-25 Z F
C208 87-012-286-080 C-CAP,U 0.01-25 K B
C213 87-012-172-080 C-CAP,U 10P-50 D CH
C215 87-010-831-080 C-CAP,U 0.1-16 Z F
C216 87-010-831-080 C-CAP,U 0.1-16 Z F
C301 87-012-280-080 CAP,U 3300P-50 K B
C318 87-012-286-080 C-CAP,U 0.01-25 K B
C401 87-010-831-080 C-CAP,U 0.1-16 Z F
C402 87-010-831-080 C-CAP,U 0.1-16 Z F
C403 87-A12-091-080 CAP,E 10-50 SMG
C404 87-A12-091-080 CAP,E 10-50 SMG
C501 87-012-282-080 C-CAP,U 4700P-50 K B
C502 87-012-278-080 C-CAP,U 2200P-50 K B
CN101 87-099-197-010 CONN,9P V BLK 6216
CN102 87-099-043-010 CONN,2P V WHT EH
CN104 87-049-919-010 CONN,3P V WHT EH
CON502 87-099-756-010 CONN,15P H 9604S F
SFR1 87-024-581-010 SFR,3.3K H KVSF637A
SOL1 82-ZM3-627-010 SOL ASSY,27 SO
SOL2 82-ZM3-627-010 SOL ASSY,27 SO
SW1 87-A90-248-010 SW,MICRO ESE11SH2CXQ