AIWA NSX-SZ50 Service Manual

NSX-SZ50

HR

SERVICE MANUAL

COMPACT DISC/

STEREO CASSETTE RECEIVER

SYSTEM

NSX–SZ50

• This Service Manual is the "Revision Publishing" and replaces "Simple Manual"
NSX-SZ50 <HR> (S/M Code No. 09-004-424-6T3).

• If requiring information about the CD mechanism, see Service Manual of AZG-1,
(S/M Code No. 09-001-335-3N6).

CD

CASSEIVER

CX–NSZ50

BASIC TAPE MECHANISM : 2ZM-3MK2 PR4NM
BASIC CD MECHANISM : AZG-1 ZD8RDM

SPEAKER

SX–WNSZ50

REMOTE

CONTROLLER

RC–ZAS01

S/M Code No. 09-004-424-6R5

REVISION

DATA

SPECIFICATIONS

Main unit CX-NSZ50
FM tuner section
Tuning range 87.5 MHz to 108 MHz
Usable sensitivity (IHF) 13.2 dBf
Antenna terminal 75 ohms (unbalanced)

MW tuner section
Tuning range 531 kHz to 1602 kHz (9 kHz step)

530 kHz to 1710 kHz (10 kHz step)

Usable sensitivity 350 µV/m
Antenna Loop antenna

SW tuner section
Tuning range 5.730 MHz to 17.900 MHz
Antenna Wire antenna

Amplifier section
Mid-high frequency amplifier
Power output Rated: 20 W + 20 W

(8 ohms, T.H.D. 1 %, 1 kHz)
Reference : 25 W + 25 W
(8 ohms, T.H.D. 10 %, 1 kHz)

Total harmonic distortion 0.1 % (10 W, 1 kHz, 8 ohms, DIN

AUDIO)

Low frequency amplifier
Power output Rated: 60 W + 60 W

(6 ohms, T.H.D. 1 %, 130 Hz)
Reference : 75 W + 75 W
(6 ohms, T.H.D. 10 %, 130 Hz)

Total harmonic distortion 0.1 % (30W, 130 Hz, 6 ohms, DIN

AUDIO)

Inputs VIDEO/AUX: 500 mV

MIC: 1.0 mV (10 k ohms)

Outputs SPEAKERS HIGH FREQ:

accept speakers of 8 ohms or more
SPEAKERS LOW FREQ:
accept speakers of 6 ohms or more
SURROUND SPEAKERS:
accept speakers of 8 ohms to 16
ohms
PHONES (stereo jack): accepts
headphones of 32 ohms or more

Cassette deck section
Track format 4 tracks, 2 channels stereo
Frequency response 50 Hz – 15000 Hz
Recording system AC bias
Heads Deck 1: Playback head x 1

Deck 2: Recording/playback head
x 1, erase head x 1

Compact disc player section
Laser Semiconductor laser (λ = 780 nm)
D-A converter 1 bit dual
Signal-to-noise ratio 85 dB (1 kHz, 0 dB)
Harmonic distortion 0.05 % (1 kHz, 0 dB)
Wow and flutter Unmeasurable

General
Power requirements 120 V/220-230 V/240 V AC

switchable, 50/60 Hz

Power consumption 150 W
Power consumption in standby mode

If the power-economizing mode is
ECO OFF: 20 W
If the power-economizing mode is
ECO ON or ECO AUTO: 0.9 W

Dimensions of main unit 260 x 326 x 345 mm
(W x H x D)
Weight of main unit 9.0 kg

Speaker system SX-WNSZ50
Speaker system 3 way, Built-in subwoofer (magnetic

shielded type)

Speaker units Subwoofer: 160 mm cone type

Full range: 100 mm cone type
Super tweeter: 20 mm ceramic type

Impedance 6 ohms/8 ohms
Sensitvity 87 dB/W/m
Dimensions (W x H x D) 240 x 324 x 271 mm
Weight 4.8 kg

• Design and specifications are subject to change without notice.

• The word “BBE” and the “BBE symbol” are trademarks of BBE

Sound, Inc.

• Under license from BBE Sound, Inc.

ACCESSORIES LIST

REF. NO PART NO. KANRI DESCRIPTION

NO.

1 8A-NF8-901-010 IB,H(ECA)M
2 8Z-NF8-702-010 RC UNIT,RC-ZAS01
3 87-006-226-010 ANT,LOOP AM
4 87-043-115-010 FEEDER-ANT,FM
5 87-A90-119-010 ANT,WIRE SW(5M)

6 87-A91-017-010 PLUG,CONVERSION JT-0476

2

PROTECTION OF EYES FROM LASER BEAM DURING SERVICING

This set employs laser. Therefore, be sure to follow carefully the

instructions below when servicing.

WARNING!

WHEN SERVICING, DO NOT APPROACH THE LASER EXIT

WITH THE EYE TOO CLOSELY. IN CASE IT IS NECESSARY TO

CONFIRM LASER BEAM EMISSION. BE SURE TO OBSERVE

FROM A DISTANCE OF MORE THAN 30cm FROM THE

SURFACE OF THE OBJECTIVE LENS ON THE OPTICAL

PICK-UP BLOCK.

Caution: Invisible laser radiation when

open and interlocks defeated avoid expo-

sure to beam.

Advarsel:Usynling laserståling ved åbning,

når sikkerhedsafbrydere er ude af funktion.

Undgå udsættelse for stråling.

VAROITUS!

Laiteen Käyttäminen muulla kuin tässä käyttöohjeessa mainit-

ulla tavalla saattaa altistaa käyt-täjän turvallisuusluokan 1 ylit-

tävälle näkymättömälle lasersäteilylle.

VARNING!

Om apparaten används på annat sätt än vad som specificeras i

denna bruksanvising, kan användaren utsättas för osynling

laserstrålning, som överskrider gränsen för laserklass 1.

CAUTION

Use of controls or adjustments or performance of procedures

other than those specified herein may result in hazardous

radiation exposure.

ATTENTION

L'utilisation de commandes, réglages ou procédures autres que

ceux spécifiés peut entraîner une dangereuse exposition aux

radiations.

ADVARSEL!

Usynlig laserståling ved åbning, når sikkerhedsafbrydereer ude

af funktion. Undgå udsættelse for stråling.

This Compact Disc player is classified as a CLASS 1 LASER

product.

The CLASS 1 LASER PRODUCT label is located on the rear

exterior.

CLASS 1
KLASSE 1
LUOKAN 1
KLASS 1

LASER PRODUCT
LASER PRODUKT
LASER LAITE
LASER APPARAT

Precaution to replace Optical block
(KSM-880CAB)

Body or clothes electrostatic potential could ruin
laser diode in the optical block. Be sure ground
body and workbench, and use care the clothes
do not touch the diode.

1) After the connection, remove solder shown in
the right figure.

PICK-UP Assy P.C.B

solder

3

NOTE ON BEFORE STARTING REPAIR

1. Forced discharge of electrolytic capacitor of power supply block

When repair is going to be attempted in the set that uses relay circuit in the power supply block, electric potential is kept charged across
the electrolytic capacitors (C101, 102) even though AC power cord is removed. If repair is attempted in this condition, secondary defect
can occur.
In order to prevent the secondary trouble, perform the following measures before starting repair work.

Discharge procedure

1 Remove the AC power cord.
2 Connect a discharging resistor at an end of lead wire that

has clips at both ends. Connect the other end of the lead
wire to metal chassis.

3 Contact the other end of the discharging resistor to the

positive (+) side (+VH) of C101. (For two seconds)

4 Contact the same end of the discharging resistor as step 3

to the negative (-) side (-VH) of C102 in the same way.
(For two seconds)

5 Check that voltage across C101 and C102 has decreased

to 1 V or less using a multimeter or an oscilloscope.

Select a discharging resistor referring to the following table.

Chargi n g v o l ta g e ( V ) Discharging

(C101, 102) resistor ( )

25-48 100 3 87-A00-247-090

49-140 220 5 87-A00-232-090

Note: The reference numbers (C101, C102) of the electrolytic capacitors can change depending on the models. Be sure to check the

reference numbers of the charging capacitors on schematic diagram before starting the discharging work.

Rated power (W) Parts number

MAIN C.B

D101

3

C101 C102

22

4

2. Check items before exchanging the MICROCOMPUTER

Be sure to check the following items before exchanging the MICROCOMPUTER. Exchange the MICROCOMPUTER after confirming
that the MICROCOMPUTER is surely defective.

2-1. Regarding the HOLD terminal of the MICROCOMPUTER

When the HOLD terminal (INPUT) of the MICROCOMPUTER is “H”, the MICROCOMPUTER is judged to be operating correctly.
When this terminal is “L”, the main power cannot be turned on. Therefore, be sure to check the terminal voltage of the HOLD
terminal before exchange.
When the MICROCOMPUTER is not defective, the HOLD terminal can also go “L” when the POWER AMPLIFIER has any
abnormalities that triggers the abnormality detection circuit on the MAIN C. B. that sets the HOLD terminal to “L”.

• Good or no good judgement of the MICROCOMPUTER

1 Turn on the AC main power.
2 Confirm that the main power is turned on and the HOLD terminal of the MICROCOMPUTER keeps the “H” level or not.
3 When the HOLD terminal is “L” level, the abnormality detection circuit is judged to be working correctly and the

MICROCOMPUTER is judged to be good.

4

In such a case, check also if the POWER AMPLIFIER circuit or power supply circuit has any abnormalities or not.

2-2. Regarding reset

There are cases that the machine does not work correctly because the MICROCOMPUTER is not reset even though the AC power
cord is re-inserted, or the software reset (pressing the STOP key + POWER key) is performed.
When the above described phenomenon occurs, it can lead to wrong judgement as if the MICROCOMPUTER is defective and to
exchange the MICROCOMPUTER. In such a case, perform the forced-reset by the following procedure and check good or no
good of the MICROCOMPUTER.

1 Remove the AC power cord.

FRONT C.B

18

MICROCOMPUTER

15

C113

C113

15

18

VSS

VDD

MICRO­COMPUTER

FRONT C.B

Short with tweezers.

Fig-2-2

2 Short both ends of the electrolytic capacitor C113 that is connected to VDD of the MICROCOMPUTER with tweezers.
3 Connect the AC power cord again. If the MICROCOMPUTER returns to the normal operation, the MICROCOMPUTER is

good.

Note: The reference number or MICROCOMPUTER pin number of transistor (Q110) and electrolytic capacitor (C113) can change depending

on the models. Be sure to check the reference numbers on schematic diagram before starting the discharging work.

2-3. Confirmation of soldering state of MICROCOMPUTER

Check the soldering state of the MICROCOMPUTER in addition to the above described procedures. Be sure to exchange the
MICROCOMPUTER after surely confirming that the trouble is not caused by poor soldering but the MICROCOMPUTER itself.

5

ELECTRICAL MAIN PARTS LIST

REF. NO PART NO. KANRI DESCRIPTION

IC

87-020-454-010 IC,DN6851
87-A21-417-010 IC,STK490-310
8A-NF8-612-110 C-IC,LC866548V-5P40
87-A21-396-010 IC,STK490-040
87-A21-629-010 IC,SPS-442-1-N

87-A21-419-040 C-IC,NJM14558MD-TE2
87-A21-023-040 C-IC,BA3835F
87-070-289-040 C-IC,BU2092F
87-A21-401-040 C-IC,M61503FP
87-A21-415-010 IC,LA1843

87-070-127-110 IC,LC72131D

TRANSISTOR

87-026-451-080 TR,2SA933S
87-026-609-080 TR,KTA1266GR
89-213-702-010 TR,2SB1370E
87-026-610-080 TR,KTC3198GR
87-A30-076-080 C-TR,2SC3052F

87-A30-075-080 C-TR,2SA1235F
87-026-245-080 TR,DTC114ES
87-A30-198-080 TR,KTC3199GR
87-A30-107-070 C-TR,CMBT5401
87-A30-106-040 C-TR,CMBT5551

87-A30-087-080 C-FET,2SK2158
87-A30-074-080 C-TR,RT1P 141C
87-A30-318-080 TR,CSA952K
87-A30-091-080 FET,2SJ460
87-A30-329-080 TR,CD1585BC

87-A30-090-080 FET,2SK2541
87-A30-104-080 C-TR,RT1N 441C
87-A30-468-080 C-TR,KRC102S-RTK
89-333-317-880 TR,2SC3331(T/U)
87-A30-269-040 C-FET,2SJ461-T1

89-327-143-080 C-TR,2SC2714O
87-A30-489-080 C-TR,KRA107S
87-A30-072-080 C-TR,RT1P 144C
87-A30-086-070 C-TR,CSD1306E
89-503-602-080 C-FET,2SK360E

87-A30-234-080 TR,CSC4115BC

DIODE

87-A40-393-090 DIODE,1N5402GW(F20)
87-020-465-080 DIODE,1SS133
87-A40-547-090 DIODE,D5SBA20
87-A40-455-080 DIODE,RL203 GW
87-A40-553-080 DIODE,1N4003 LES

87-A40-776-080 ZENER,UZ27BSD
87-A40-764-080 ZENER,UZ10BSC
87-A40-270-080 C-DIODE,MC2838
87-A40-313-080 C-DIODE,MC2840
87-A40-269-080 C-DIODE,MC2836

87-A40-768-080 ZENER,UZ16BSA
87-A40-752-080 ZENER,UZ6.2BSC
87-A40-802-080 ZENER,UZ5.1BSC
87-A40-739-080 ZENER,UZ2.7BSA
87-A40-618-080 VARI-CAP,SVC 348(S/T)

87-017-149-080 ZENER,HZS6A2L

MAIN C.B

C0003 87-012-368-080 C-CAP,S 0.1-50 Z F
C0004 87-012-368-080 C-CAP,S 0.1-50 Z F
C0005 87-012-368-080 C-CAP,S 0.1-50 Z F
C0006 87-012-368-080 C-CAP,S 0.1-50 Z F
C0009 87-012-368-080 C-CAP,S 0.1-50 Z F

NO.

REF. NO PART NO. KANRI DESCRIPTION

C0010 87-012-368-080 C-CAP,S 0.1-50 Z F
C0011 87-012-368-080 C-CAP,S 0.1-50 Z F
C0012 87-012-368-080 C-CAP,S 0.1-50 Z F
C0015 87-012-368-080 C-CAP,S 0.1-50 Z F
C0016 87-012-368-080 C-CAP,S 0.1-50 Z F

C0017 87-012-368-080 C-CAP,S 0.1-50 Z F
C0018 87-012-368-080 C-CAP,S 0.1-50 Z F
C0019 87-016-520-000 CAP,E 3300-65 M SMG
C0020 87-016-520-000 CAP,E 3300-65 M SMG
C0021 87-016-051-000 CAP,E 2200-35 M SMG

C0022 87-016-051-000 CAP,E 2200-35 M SMG
C0023 87-016-658-000 CAP,E 4700-35 M SMG
C0024 87-016-658-000 CAP,E 4700-35 M SMG
C0025 87-010-408-080 CAP,E 47-50 M 11L SME
C0026 87-010-247-080 CAP,E 100-50 M SME

C0030 87-010-430-080 CAP,E 100-63
C0031 87-010-263-080 CAP,E 100-10 M 11L SME
C0032 87-010-197-080 C-CAP,S 0.01-25 K B C2012
C0034 87-010-260-080 CAP,E 47-25 M 11L SME
C0035 87-010-380-080 CAP,E 47-16 M 11L SME

C0036 87-010-381-080 CAP,E 330-16 M SME
C0038 87-010-197-080 C-CAP,S 0.01-25 K B C2012
C0060 87-010-403-080 CAP,E 3.3-50 M 11L SME
C0061 87-010-260-080 CAP,E 47-25 M 11L SME
C0101 87-010-183-080 C-CAP,S 2700P-50 K B GRM

C0102 87-010-183-080 C-CAP,S 2700P-50 K B GRM
C0103 87-010-545-080 CAP,E 0.22-50 M 11L SME
C0104 87-010-545-080 CAP,E 0.22-50 M 11L SME
C0107 87-010-405-080 CAP,E 10-50 M 11L SME
C0108 87-010-405-080 CAP,E 10-50 M 11L SME

C0111 87-010-405-080 CAP,E 10-50 M 11L SME
C0112 87-010-405-080 CAP,E 10-50 M 11L SME
C0113 87-010-866-080 CAP,E 10-63 M VX
C0114 87-010-866-080 CAP,E 10-63 M VX
C0119 87-010-197-080 C-CAP,S 0.01-25 K B C2012

C0120 87-010-197-080 C-CAP,S 0.01-25 K B C2012
C0125 87-012-368-080 C-CAP,S 0.1-50 Z F
C0126 87-012-368-080 C-CAP,S 0.1-50 Z F
C0127 87-012-368-080 C-CAP,S 0.1-50 Z F
C0128 87-012-368-080 C-CAP,S 0.1-50 Z F

C0133 87-010-186-080 C-CAP,S 4700P-50 K B C2012
C0140 87-010-182-080 C-CAP,S 2200P-50 K B C2012
C0141 87-010-196-080 C-CAP,S 0.1-25 Z F C2012
C0203 87-010-182-080 C-CAP,S 2200P-50 K B C2012
C0204 87-010-182-080 C-CAP,S 2200P-50 K B C2012

C0205 87-012-140-080 C-CAP,S 470P-50 J CH
C0206 87-012-140-080 C-CAP,S 470P-50 J CH
C0209 87-010-402-080 CAP,E 2.2-50 M 11L SME
C0210 87-010-402-080 CAP,E 2.2-50 M 11L SME
C0211 87-010-184-080 C-CAP,S 3300P-50 K B C2012

C0212 87-010-184-080 C-CAP,S 3300P-50 K B C2012
C0213 87-010-402-080 CAP,E 2.2-50 M 11L SME
C0214 87-010-402-080 CAP,E 2.2-50 M 11L SME
C0217 87-010-405-080 CAP,E 10-50 M 11L SME
C0218 87-010-405-080 CAP,E 10-50 M 11L SME

C0220 87-010-405-080 CAP,E 10-50 M 11L SME
C0223 87-010-190-080 C-CAP,S 0.01-50 Z F C2012
C0224 87-010-190-080 C-CAP,S 0.01-50 Z F C2012
C0228 87-010-405-080 CAP,E 10-50 M 11L SME
C0229 87-010-196-080 C-CAP,S 0.1-25 Z F C2012

C0230 87-010-196-080 C-CAP,S 0.1-25 Z F C2012
C0231 87-010-196-080 C-CAP,S 0.1-25 Z F C2012
C0232 87-010-196-080 C-CAP,S 0.1-25 Z F C2012
C0239 87-010-196-080 C-CAP,S 0.1-25 Z F C2012
C0301 87-010-178-080 C-CAP,S 1000P-50 K B C2012

C0302 87-010-178-080 C-CAP,S 1000P-50 K B C2012
C0303 87-010-178-080 C-CAP,S 1000P-50 K B C2012
C0304 87-010-178-080 C-CAP,S 1000P-50 K B C2012
C0307 87-010-263-080 CAP,E 100-10 M 11L SME
C0308 87-010-263-080 CAP,E 100-10 M 11L SME

NO.

6

REF. NO PART NO. KANRI DESCRIPTION

C0309 87-010-318-080 C-CAP,S 47P-50 J CH GRM
C0310 87-010-318-080 C-CAP,S 47P-50 J CH GRM
C0313 87-010-188-080 C-CAP,S 6800P-50 K B C2012
C0314 87-010-188-080 C-CAP,S 6800P-50 K B C2012
C0315 87-010-263-080 CAP,E 100-10 M 11L SME

C0317 87-010-546-080 CAP,E 0.33-50 M 11L SME
C0318 87-010-546-080 CAP,E 0.33-50 M 11L SME
C0326 87-010-198-080 C-CAP,S 0.022-25 K B C2012
C0327 87-012-368-080 C-CAP,S 0.1-50 Z F
C0360 87-010-401-080 CAP,E 1-50 M 11L SME

C0399 87-012-140-080 C-CAP,S 470P-50 J CH
C0401 87-010-544-080 CAP,E 0.1-50 M 11L SME
C0402 87-010-544-080 CAP,E 0.1-50 M 11L SME
C0403 87-010-321-080 C-CAP,S 82P-50 J CH
C0404 87-010-321-080 C-CAP,S 82P-50 J CH

C0405 87-010-197-080 C-CAP,S 0.01-25 K B C2012
C0406 87-010-197-080 C-CAP,S 0.01-25 K B C2012
C0407 87-010-197-080 C-CAP,S 0.01-25 K B C2012
C0408 87-010-197-080 C-CAP,S 0.01-25 K B C2012
C0409 87-010-182-080 C-CAP,S 2200P-50 K B C2012

C0410 87-010-182-080 C-CAP,S 2200P-50 K B C2012
C0411 87-010-405-080 CAP,E 10-50 M 11L SME
C0412 87-010-405-080 CAP,E 10-50 M 11L SME
C0452 87-010-382-080 CAP,E 22-25 M 11L SME
C0453 87-010-183-080 C-CAP,S 2700P-50 K B GRM

C0454 87-010-183-080 C-CAP,S 2700P-50 K B GRM
C0455 87-010-183-080 C-CAP,S 2700P-50 K B GRM
C0456 87-010-197-080 C-CAP,S 0.01-25 K B C2012
C0458 87-010-178-080 C-CAP,S 1000P-50 K B C2012
C0459 87-010-175-080 C-CAP,S 560P-50 J SL

C0460 87-010-196-080 C-CAP,S 0.1-25 Z F C2012
C0461 87-012-158-080 C-CAP,S 390P-50 J CH GRM
C0462 87-012-158-080 C-CAP,S 390P-50 J CH GRM
C0507 87-010-196-080 C-CAP,S 0.1-25 Z F C2012
C0508 87-010-178-080 C-CAP,S 1000P-50 K B C2012

C0509 87-A10-300-080 CAP,M 0.027-50 J
C0510 87-A10-300-080 CAP,M 0.027-50 J
C0515 87-A10-300-080 CAP,M 0.027-50 J
C0516 87-A10-300-080 CAP,M 0.027-50 J
C0518 87-010-196-080 C-CAP,S 0.1-25 Z F C2012

C0519 87-010-401-080 CAP,E 1-50 M 11L SME
C0520 87-010-401-080 CAP,E 1-50 M 11L SME
C0521 87-010-546-080 CAP,E 0.33-50 M 11L SME
C0522 87-010-546-080 CAP,E 0.33-50 M 11L SME
C0523 87-010-545-080 CAP,E 0.22-50 M 11L SME

C0524 87-010-545-080 CAP,E 0.22-50 M 11L SME
C0525 87-010-545-080 CAP,E 0.22-50 M 11L SME
C0526 87-010-545-080 CAP,E 0.22-50 M 11L SME
C0605 87-010-179-080 C-CAP,S 1200P-50 K B GRM
C0606 87-010-179-080 C-CAP,S 1200P-50 K B GRM

C0609 87-010-213-080 C-CAP,S 0.015-25 K B GRM
C0610 87-010-213-080 C-CAP,S 0.015-25 K B GRM
C0611 87-010-545-080 CAP,E 0.22-50 M 11L SME
C0612 87-010-545-080 CAP,E 0.22-50 M 11L SME
C0613 87-010-545-080 CAP,E 0.22-50 M 11L SME

C0614 87-010-545-080 CAP,E 0.22-50 M 11L SME
C0615 87-010-154-080 C-CAP,S 10P-50 D CH GRM
C0616 87-010-385-080 CAP,E 220-25 M SME
C0617 87-010-385-080 CAP,E 220-25 M SME
C0618 87-010-405-080 CAP,E 10-50 M 11L SME

C0620 87-010-263-080 CAP,E 100-10 M 11L SME
C0630 87-016-669-080 C-CAP,S 0.1-25 K B
C0631 87-010-185-080 C-CAP,S 3900P-50 K B
C0632 87-010-185-080 C-CAP,S 3900P-50 K B
C0633 87-016-369-080 C-CAP,S 0.033-25 K B GRM

C0634 87-016-369-080 C-CAP,S 0.033-25 K B GRM
C0661 87-010-178-080 C-CAP,S 1000P-50 K B C2012
C0662 87-010-178-080 C-CAP,S 1000P-50 K B C2012
C0671 87-010-196-080 C-CAP,S 0.1-25 Z F C2012
C0672 87-010-196-080 C-CAP,S 0.1-25 Z F C2012

NO.

REF. NO PART NO. KANRI DESCRIPTION

C0673 87-010-182-080 C-CAP,S 2200P-50 K B C2012
C0677 87-010-197-080 C-CAP,S 0.01-25 K B C2012
C0771 87-010-263-080 CAP,E 100-10 M 11L SME
C0772 87-010-197-080 C-CAP,S 0.01-25 K B C2012
C0782 87-010-197-080 C-CAP,S 0.01-25 K B C2012

C0783 87-010-197-080 C-CAP,S 0.01-25 K B C2012
C0784 87-010-197-080 C-CAP,S 0.01-25 K B C2012
C0785 87-010-197-080 C-CAP,S 0.01-25 K B C2012
C0786 87-010-197-080 C-CAP,S 0.01-25 K B C2012
C0788 87-010-149-080 C-CAP,S 5P-50 C CH GRM

C0789 87-A11-532-080 C-CAP,S 0.022-50 J B
C0790 87-A11-532-080 C-CAP,S 0.022-50 J B
C0791 87-010-196-080 C-CAP,S 0.1-25 Z F C2012
C0792 87-010-197-080 C-CAP,S 0.01-25 K B C2012
C0793 87-010-404-080 CAP,E 4.7-50 M 11L SME

C0795 87-010-197-080 C-CAP,S 0.01-25 K B C2012
C0796 87-010-197-080 C-CAP,S 0.01-25 K B C2012
C0797 87-010-405-080 CAP,E 10-50 M 11L SME
C0798 87-010-197-080 C-CAP,S 0.01-25 K B C2012
C0799 87-010-407-080 CAP,E 33-50 M 11L SME

C0800 87-012-369-080 C-CAP,S 0.047-50 Z F
C0801 87-010-403-080 CAP,E 3.3-50 M 11L SME
C0802 87-010-194-080 C-CAP,S 0.047-25 Z F
C0803 87-010-198-080 C-CAP,S 0.022-25 K B C2012
C0804 87-010-263-080 CAP,E 100-10 M 11L SME

C0807 87-010-400-080 CAP,E 0.47-50 M 11L SME
C0808 87-010-401-080 CAP,E 1-50 M 11L SME
C0809 87-010-401-080 CAP,E 1-50 M 11L SME
C0810 87-010-196-080 C-CAP,S 0.1-25 Z F C2012
C0814 87-010-197-080 C-CAP,S 0.01-25 K B C2012

C0815 87-010-400-080 CAP,E 0.47-50 M 11L SME
C0816 87-010-400-080 CAP,E 0.47-50 M 11L SME
C0821 87-010-405-080 CAP,E 10-50 M 11L SME
C0823 87-010-177-080 C-CAP,S 820P-50 J SL C2012
C0824 87-010-405-080 CAP,E 10-50 M 11L SME

C0825 87-010-596-080 C-CAP,S 0.047-16 K R C2012
C0842 87-010-197-080 C-CAP,S 0.01-25 K B C2012
C0844 87-010-197-080 C-CAP,S 0.01-25 K B C2012
C0850 87-010-260-080 CAP,E 47-25 M 11L SME
C0851 87-010-197-080 C-CAP,S 0.01-25 K B C2012

C0852 87-010-197-080 C-CAP,S 0.01-25 K B C2012
C0853 87-010-197-080 C-CAP,S 0.01-25 K B C2012
C0858 87-010-196-080 C-CAP,S 0.1-25 Z F C2012
C0859 87-010-196-080 C-CAP,S 0.1-25 Z F C2012
C0860 87-010-197-080 C-CAP,S 0.01-25 K B C2012

C0940 87-010-197-080 C-CAP,S 0.01-25 K B C2012
C0941 87-010-314-080 C-CAP,S 22P-50 J CH GRM
C0943 87-010-197-080 C-CAP,S 0.01-25 K B C2012
C0945 87-010-197-080 C-CAP,S 0.01-25 K B C2012
C0946 87-010-971-080 C-CAP,S 4700P-50 J B

C0947 87-010-197-080 C-CAP,S 0.01-25 K B C2012
C0948 87-010-148-080 C-CAP,S 4P-50 C CH GRM
C0952 87-010-197-080 C-CAP,S 0.01-25 K B C2012
C0953 87-010-197-080 C-CAP,S 0.01-25 K B C2012
C0954 87-010-400-080 CAP,E 0.47-50 M 11L SME

C0956 87-010-263-080 CAP,E 100-10 M 11L SME
C0959 87-010-196-080 C-CAP,S 0.1-25 Z F C2012
C0962 87-010-401-080 CAP,E 1-50 M 11L SME
C0963 87-015-785-080 C-CAP, 0.1-25 Z F C3216
C0964 87-010-854-080 C-CAP,S 560P-50 J CH

C0971 87-010-381-080 CAP,E 330-16 M SME
C0972 87-010-404-080 CAP,E 4.7-50 M 11L SME
C0973 87-010-197-080 C-CAP,S 0.01-25 K B C2012
C0974 87-010-197-080 C-CAP,S 0.01-25 K B C2012
C0979 87-010-322-080 C-CAP,S 100P-50 J CH GRM

C0981 87-010-260-080 CAP,E 47-25 M 11L SME
C0982 87-010-196-080 C-CAP,S 0.1-25 Z F C2012
C0983 87-010-197-080 C-CAP,S 0.01-25 K B C2012
C0984 87-010-197-080 C-CAP,S 0.01-25 K B C2012
C0987 87-010-197-080 C-CAP,S 0.01-25 K B C2012

NO.

7

REF. NO PART NO. KANRI DESCRIPTION

C0989 87-010-197-080 C-CAP,S 0.01-25 K B C2012
C0991 87-010-312-080 C-CAP,S 15P-50 J CH GRM
C0992 87-010-312-080 C-CAP,S 15P-50 J CH GRM
C0993 87-010-178-080 C-CAP,S 1000P-50 K B C2012
C0995 87-010-178-080 C-CAP,S 1000P-50 K B C2012

C0997 87-010-196-080 C-CAP,S 0.1-25 Z F C2012
C0998 87-010-260-080 CAP,E 47-25 M 11L SME
C0999 87-A11-132-080 CAP,TC U 0.01-50 K B
CF0831 87-008-261-010 FLTR,CF SFE10.7MA5
CF0832 87-008-261-010 FLTR,CF SFE10.7MA5

CN0301 87-A60-620-010 CONN,3P V 2MM JMT
CN0351 87-A60-625-010 CONN,8P V 2MM JMT
CN0601 87-099-719-010 CONN,30P H BLK TYK-B(X)
CN0602 87-A60-131-010 CONN,6P V FE
CNA0001 8A-NF8-654-010 CONN ASSY,11P TID-A(480)

FFC0602 88-906-251-110 FF-CABLE,6P 1.25
FFE0831 A8-8ZA-190-030 8ZA-1 FEUNM
J0202 87-A60-483-010 JACK,DIA6.3 BLK ST W/S KM
J0203 87-A60-238-010 TERMINAL,SP 4P (MSC)
J0204 87-A61-153-010 JACK,PIN 4P R/W(BL) (SEPA) KM

J0602 87-A60-881-010 JACK,PIN 2P MSP 242V05 PBSN
J0831 87-A60-202-010 TERMINAL,ANT 4P MSP-154V-02
J0940 87-A60-633-010 CONN,2P H 2.5MM JMT
L0101 87-003-383-010 COIL,1UH K
L0102 87-003-383-010 COIL,1UH K

L0201 87-003-383-010 COIL,1UH K
L0202 87-003-383-010 COIL,1UH K
L0451 87-007-342-010 COIL,OSC 85KHZ BIAS
L0801 87-A50-540-010 COIL,FM DET(TOK)
L0802 87-A91-552-010 FLTR,CFMT-450AL (TOK)

L0811 87-005-847-080 COIL,2.2UH K CECS
L0832 87-005-847-080 COIL,2.2UH K CECS
L0941 87-A50-022-010 COIL,ANT SW (COI) 7.96MHZ
L0942 87-A50-550-010 COIL,OSC SW-2N(COI)
L0943 87-A50-522-080 COIL,1MH K CEC

L0944 87-A50-159-010 COIL,10MH K C2B
L0952 87-A50-430-010 COIL,ANT MW(3BSW)
L0953 87-A50-431-010 COIL,OSC MW(3BSW)
R0129 87-A00-257-080 RES,M/F 0.15-1W J
R0130 87-A00-257-080 RES,M/F 0.15-1W J

R0143 87-A00-440-050 RES,220-1/2W J RP
R0144 87-A00-440-050 RES,220-1/2W J RP
R0145 87-A00-440-050 RES,220-1/2W J RP
R0146 87-A00-440-050 RES,220-1/2W J RP
R0233 87-A00-258-080 RES,M/F 0.22-1W J

R0234 87-A00-258-080 RES,M/F 0.22-1W J
R0790 87-010-197-080 C-CAP,S 0.01-25 K B C2012
R0991 87-010-322-080 C-CAP,S 100P-50 J CH GRM
R0993 87-010-322-080 C-CAP,S 100P-50 J CH GRM
R0995 87-010-322-080 C-CAP,S 100P-50 J CH GRM

SFR0451 87-A90-432-080 SFR,30K H NVZ6TLTA
SFR0452 87-A90-432-080 SFR,30K H NVZ6TLTA
TC0941 87-011-254-080 TRIMMER,CER 20P 4.0X4.5 ECR
TC0943 87-011-253-080 TRIMMER,CER 30P 4.0X4.5 ECRLA
WH0001 87-A91-179-010 HLDR,WIRE 2.5-11P

X0991 87-A70-061-010 VIB,XTAL 4.500MHZ CSA-309

FRONT C.B
C0201 87-010-322-080 C-CAP,S 100P-50 J CH GRM

C0202 87-010-322-080 C-CAP,S 100P-50 J CH GRM
C0203 87-010-322-080 C-CAP,S 100P-50 J CH GRM
C0204 87-010-322-080 C-CAP,S 100P-50 J CH GRM
C0205 87-010-322-080 C-CAP,S 100P-50 J CH GRM

C0206 87-010-322-080 C-CAP,S 100P-50 J CH GRM
C0207 87-010-322-080 C-CAP,S 100P-50 J CH GRM
C0208 87-010-322-080 C-CAP,S 100P-50 J CH GRM
C0209 87-010-322-080 C-CAP,S 100P-50 J CH GRM
C0210 87-010-322-080 C-CAP,S 100P-50 J CH GRM

NO.

C0211 87-010-322-080 C-CAP,S 100P-50 J CH GRM
C0251 87-010-405-040 CAP,E 10-50 M 11L SME
C0253 87-010-196-080 C-CAP,S 0.1-25 Z F C2012
C0254 87-012-369-080 C-CAP,S 0.047-50 Z F
C0255 87-010-560-040 CAP,E 10-50 M 5L MA

C0256 87-010-405-040 CAP,E 10-50 M 11L SME
C0259 87-010-405-040 CAP,E 10-50 M 11L SME
C0264 87-A11-148-080 CAP,TC U 0.1-50 Z F
C0273 87-010-178-080 C-CAP,S 1000P-50 K B C2012
C0274 87-010-178-080 C-CAP,S 1000P-50 K B C2012

C0301 87-010-182-080 C-CAP,S 2200P-50 K B C2012
C0302 87-010-196-080 C-CAP,S 0.1-25 Z F C2012
C0303 87-010-196-080 C-CAP,S 0.1-25 Z F C2012
C0312 87-010-498-040 CAP,E 10-16 M 5L SRE
C0314 87-010-196-080 C-CAP,S 0.1-25 Z F C2012

C0315 87-010-196-080 C-CAP,S 0.1-25 Z F C2012
C0316 87-010-196-080 C-CAP,S 0.1-25 Z F C2012
C0321 87-012-393-080 C-CAP,S 0.22-16 K W5R CM/CB
C0322 87-010-400-040 CAP,E 0.47-50 M 11L SME
C0325 87-A10-189-040 CAP,E 220-10 M 5L

C0326 87-A10-189-040 CAP,E 220-10 M 5L
C0332 87-010-178-080 C-CAP,S 1000P-50 K B C2012
C0334 87-010-312-080 C-CAP,S 15P-50 J CH GRM
C0335 87-012-140-080 C-CAP,S 470P-50 J CH
C0336 87-012-155-080 C-CAP,S 180P-50 J CH GRM

C0339 87-012-156-080 C-CAP,S 220P-50 J CH GRM
C0340 87-010-197-080 C-CAP,S 0.01-25 K B C2012
C0341 87-010-194-080 C-CAP,S 0.047-25 Z F
C0351 87-010-382-040 CAP,E 22-25 M 11L SME
C0401 87-010-197-080 C-CAP,S 0.01-25 K B C2012

C0451 87-010-196-080 C-CAP,S 0.1-25 Z F C2012
C0452 87-010-196-080 C-CAP,S 0.1-25 Z F C2012
C0453 87-010-196-080 C-CAP,S 0.1-25 Z F C2012
C0454 87-010-196-080 C-CAP,S 0.1-25 Z F C2012
C0455 87-010-196-080 C-CAP,S 0.1-25 Z F C2012

C0502 87-010-186-080 C-CAP,S 4700P-50 K B C2012
C0503 87-010-112-040 CAP,E 100-16 M 11L SME
C0504 87-010-405-040 CAP,E 10-50 M 11L SME
C0505 87-010-545-040 CAP,E 0.22-50 M 11L SME
C0506 87-010-320-080 C-CAP,S 68P-50 J CH GRM

C0507 87-010-544-040 CAP,E 0.1-50 M 11L SME
C0508 87-010-544-040 CAP,E 0.1-50 M 11L SME
C0510 87-010-322-080 C-CAP,S 100P-50 J CH GRM
C0511 87-010-265-040 CAP,E 33-16 M 11L SME
C0512 87-010-178-080 C-CAP,S 1000P-50 K B C2012

C0513 87-010-196-080 C-CAP,S 0.1-25 Z F C2012
C0515 87-010-178-080 C-CAP,S 1000P-50 K B C2012
C0520 87-010-178-080 C-CAP,S 1000P-50 K B C2012
C0602 87-010-322-080 C-CAP,S 100P-50 J CH GRM
C0603 87-010-322-080 C-CAP,S 100P-50 J CH GRM

C0604 87-010-322-080 C-CAP,S 100P-50 J CH GRM
C0650 87-010-196-080 C-CAP,S 0.1-25 Z F C2012
C0699 87-010-196-080 C-CAP,S 0.1-25 Z F C2012
CN0101 87-099-720-010 CONN,30P BLK TYK-B(P)
CN0102 87-099-015-010 CONN,13P V BLK 6216

CN0301 87-A60-140-010 CONN,15P V FE
FB0301 87-008-372-080 FLTR,EMI BL01 RN1
FB0501 87-008-372-080 FLTR,EMI BL01 RN1
FFC0102 88-913-301-110 FF-CABLE,13P-1.25
FFC0302 88-915-101-110 FF-CABLE, 15P 1.25 100MM

FL0401 8A-NF8-601-010 FL,HNA-11MM30(ANF-8)
J0501 87-A61-242-010 JACK,6.3 BLK MONO W/SW V KM
L0331 87-A50-408-010 COIL,OSC 5.76MHZ
LED0311 87-A40-589-040 LED,SLR-56VCT31 RED
LED0601 87-A40-803-010 LED,SELU1E10CXM-S LF38 BLUE

LED0602 87-A40-619-080 LED,SLR-56PT-TE7-W GRN
LED0603 87-A40-619-080 LED,SLR-56PT-TE7-W GRN
LED0604 87-A40-619-080 LED,SLR-56PT-TE7-W GRN
LED0606 87-A40-619-080 LED,SLR-56PT-TE7-W GRN
LED0607 87-A40-619-080 LED,SLR-56PT-TE7-W GRN

REF. NO PART NO. KANRI DESCRIPTION

NO.

8