AIWA NSX-R1 Service Manual

NSX-R11

EZ(S)

SERVICE MANUAL

CD STEREO SYSTEM

CD

CASSEIVER

NSX–R11

• This Service Manual is the "Revision Publishing" and replaces "Simple Manual" (S/M Code No. 09-023-455-6T1).

BASIC CD MECHANISM : BZG-2 ZD9GNC1 BASIC TAPE MECHANISM : CMAT6Z2(1+1)ALPS

SPEAKERSYSTEM

SX–NR10CX–NR11

REMOTE

CONTROLLER

RC–CAS03(VS)

• If requiring information about the CD mechanism, see Service Manual of

BZG-2, (S/M Code No. 09-023-353-2N8).

S/M Code No. 09-024-455-6R1

REVISION

DATA

TABLE OF CONTENTS

SPECIFICATIONS...............................................................................................................................................................3

PROTECTION OF EYES FROM LASER BEAM DURING SERVICING .......................................................................4

NOTE ON BEFORE STARTING REPAIR ...................................................................................................................5, 6

ELECTRICAL PARTS LIST (CX – NR11).................................................................................................................7 ~ 19

CHIP RESISTOR PART CODE......................................................................................................................................20

TRANSISTOR ILLUSTRATION........................................................................................................................................21

WIRING – 1 (MAIN / HP) ................................................................................................................................................22

SCHEMATIC DIAGRAM – 1 (MAIN 1 / 2).......................................................................................................................23

SCHEMATIC DIAGRAM – 2 (MAIN 2 / 2).......................................................................................................................24

SCHEMATIC DIAGRAM – 3 (HP) ...................................................................................................................................25

WIRING – 2 (FRONT) ......................................................................................................................................................26

SCHEMATIC DIAGRAM – 4 (FRONT / DECK) .............................................................................................................27

WIRING – 3 (PT) ..............................................................................................................................................................28

SCHEMATIC DIAGRAM – 5 (PT) ................................................................................................................................. ..29

WIRING – 4 (DECK) .........................................................................................................................................................30

IC BLOCK DIAGRAM ......................................................................................................................................................31

FL (HUA – 13SS09T) GRID ASSIGNMENT / PIN CONNECTION / ANODE CONNECTION ...................................32

IC DESCRIPTION ......................................................................................................................................................33, 34

ADJUSTMENT (TUNER / DECK / FRONT)..........................................................................................................35 ~ 41

CD TEST MODE .............................................................................................................................................................42

MECHANICAL EXPLODED VIEW.................................................................................................................................. 43

MECHANICAL PARTS LIST........................................................................................................................................... 44

COLOR NAME TABLE ....................................................................................................................................................45

TAPE MECHANISM EXPLODED VIEW ........................................................................................................................ 46

TAPE MECHANISM PARTS LIST ..................................................................................................................................47

GENERAL SPEAKER DISASSEMBLY INSTRUCTIONS (FOR REFERENCE) ............................................................48

SPEAKER PARTS LIST (SX – NR10) ............................................................................................................................ 49

ACCESSORIES / PARTS LIST ......................................................................................................................................50

OTHER PARTS LIST (CX – NR11) ................................................................................................................................51

– 2 –

SPECIFICATIONS

MAIN UNIT CX-NR11

TUNER FM tuning range 87.5 MHz to 108 MHz FM usable sensitivity (IHF) 16.8 dBf FM antenna terminals 75 ohms (unbalanced) MW tuning range 531 kHz to 1602 kHz (9 kHz step)

MW usable sensitivity 350 µV/m LW tuning range 144 kHz to 290 kHz LW usable sensitivity 1400 uV/m MW/LW antenna Loop antenna

AMPLIFIER Power output Rated: 8 W + 8 W (6 ohms,

Total harmonic distortion Input VIDEO / AUX: 500mV

Outputs SPEAKERS: 6 ohms or more

CASSETTE DECK Track format 4 tracks, 2 channels stereo Frequency response 50 Hz - 15 kHz Recording system AC bias Heads DECK 1: playback x 1

530 kHz to 1710 kHz (10 kHz step)

T.H.D. 1 %, 1 kHz/DIN 45500) Reference: 10 W + 10 W (6 ohms, T.H.D. 10 %, 1 kHz/DIN 45324) DIN MUSIC POWER: 26 W + 26 W

0.08 % (6 W, 1 kHz, 6 ohm, DIN AUDIO)

PHONES: 32 ohms or more

DECK 2: recording / playback x 1, erase x 1

CD PLAYER Laser Semiconductor laser (λ = 780 nm) D/A converter 1 bit dual Signal - to - noise ratio 85 dB (1 kHz, 0 dB) Harmonic distortion 0.05 % (1 kHz, 0 dB)

GENERAL Power requirements 230 V AC, 50 Hz Power consumption 42 W Dimensions (W x H x D) 260 x 324 x 315 mm Weight 4.7 kg

FRONT SPEKERS SX – NR10

Speaker system 1 way, bass reflex (magnetic shielded) Speakers units Full range : 100 mm cone Impedance 6 ohms Dimensions (W x H x D) 210 x 324 x 202 mm Weight 2.8 kg

• Design and specifications are subject to change without notice.

– 3 –

PROTECTION OF EYES FROM LASER BEAM DURING SERVICING

This set employs laser. Therefore, be sure to follow carefully the instructions below when servicing.

WARNING!!

WHEN SERVICING, DO NOT APPROACH THE LASER EXIT WITH THE EYE TOO CLOSELY. IN CASE IT IS NECESSARY TO CONFIRM LASER BEAM EMISSION. BE SURE TO OBSERVE FROM A DISTANCE OF MORE THAN 30cm FROM THE SURFACE OF THE OBJECTIVE LENS ON THE OPTICAL PICK-UP BLOCK.

Caution: Invisible laser radiation when open and interlocks defeated avoid exposure to beam. Advarsel: Usynlig laserståling ved åbning, når sikkerhedsafbrydere er ude af funktion. Undgå udsættelse for stråling.

VAROITUS!

Laiteen Käyttäminen muulla kuin tässä käyttöohjeessa mainitulla tavalla saataa altistaa käyt-täjän turvallisuusluokan 1 ylittävälle näkymättömälle lasersäteilylle.

VARNING!

Om apparaten används på annat sätt än vad som specificeras i denna bruksanvising, kan användaren utsättas för osynling laserstrålning, som överskrider gränsen för laserklass 1.

CAUTION

Use of controls or adjustments or performance of procedures other than those specified herin may result in hazardous radiation exposure.

ATTENTION

L’utillisation de commandes, réglages ou procédures autres que ceux spécifiés peut entraîner une dangereuse exposition aux radiations.

ADVARSEL

Usynlig laserståling ved åbning, når sikkerhedsafbrydereer ude af funktion. Undgå udsættelse for stråling.

This Compact Disc player is classified as a CLASS 1 LASER product. The CLASS 1 LASER PRODUCT label is located on the rear exterior.

CLASS 1 LASER PRODUCT KLASSE 1 LASER PRODUKT LUOKAN 1 LASER LAITE KLASS 1 LASER APPARAT

Precaution to replace Optical block (BZG-6 YANC)

(PXR-104X-BP-0101)

Body or clothes electrostatic potential could ruin laser diode in the optical block. Be sure ground body and workbench, and use care the clothes do not touch the diode.

1) After the connection, remove solder shown in right figure.

– 4 –

CD PICK-UP Assy PWB

Solder

NOTE ON BEFORE STARTING REPAIR

1. Forced discharge of electrolytic capacitor of power supply block

When repair is going to be attempted in the set that uses relay circuit in the power supply block, electric potential is kept charged across the electrolytic capacitors (C101, 102) even though AC power cord is removed. If repair is attempted in this condition, secondary defect can occur. In order to prevent the secondary trouble, perform the following measures before starting repair work.

Discharge procedure

11

1 Remove the AC power cord.

11 22

2 Connect a discharging resistor at an end of lead wire that

22

has clips at both ends. Connect the other end of the lead wire to metal chassis.

33

3 Contact the other end of the discharging resistor to the

33

positive (+) side (+VH) of C101. (For two seconds)

44

4 Contact the same end of the discharging resistor as step

44

33

3 to the negative (-) side (-VH) of C102 in the same way.

33

(For two seconds)

55

5 Check that voltage across C101 and C102 has decreased

55

to 1 V or less using a multimeter or an oscilloscope.

Select a discharging resistor referring to the following table.

Charging voltage (V) Discharging

(C101, 102) resistor (Ω)

25-48 100 3 87-A00-247-090

49-140 220 5 87-A00-232-090

Note: The reference numbers (C101, C102) of the electrolytic capacitors can change depending on the models. Be sure to check the

reference numbers of the charging capacitors on schematic diagram before starting the discharging work.

Rated power (W) Parts number

MAIN C.B

D101

3

C101 C102

22

Fig-1

4

2. Check items before exchanging the MICROCOMPUTER

Be sure to check the following items before exchanging the MICROCOMPUTER. Exchange the MICROCOMPUTER after confirming that the MICROCOMPUTER is surely defective.

2-1. Regarding the HOLD terminal of the MICROCOMPUTER

When the HOLD terminal (INPUT) of the MICROCOMPUTER is “H”, the MICROCOMPUTER is judged to be operating correctly. When this terminal is “L”, the main power cannot be turned on. Therefore, be sure to check the terminal voltage of the HOLD terminal before exchange. When the MICROCOMPUTER is not defective, the HOLD terminal can also go “L” when the POWER AMPLIFIER has any abnormalities that triggers the abnormality detection circuit on the MAIN C. B. that sets the HOLD terminal to “L”.

• Good or no good judgement of the MICROCOMPUTER

11

1 Turn on the AC main power.

11 22

2 Confirm that the main power is turned on and the HOLD terminal of the MICROCOMPUTER keeps the “H” level or not.

22 33

3 When the HOLD terminal is “L” level, the abnormality detection circuit is judged to be working correctly and the

33

MICROCOMPUTER is judged to be good.

– 5 –

In such a case, check also if the POWER AMPLIFIER circuit or power supply circuit has any abnormalities or not.

2-2. Regarding reset

There are cases that the machine does not work correctly because the MICROCOMPUTER is not reset even though the AC power cord is re-inserted, or the software reset (pressing the STOP key + POWER key) is performed. When the above described phenomenon occurs, it can lead to wrong judgement as if the MICROCOMPUTER is defective and to exchange the MICROCOMPUTER. In such a case, perform the forced-reset by the following procedure and check good or no good of the MICROCOMPUTER.

11

1 Remove the AC power cord.

11

FRONT C.B

18

MICROCOMPUTER

FRONT C.B

22

2 Short both ends of the electrolytic capacitor C113 that is connected to VDD of the MICROCOMPUTER with tweezers.

22 33

3 Connect the AC power cord again. If the MICROCOMPUTER returns to the normal operation, the MICROCOMPUTER is

33

good.

Note: The reference number or MICROCOMPUTER pin number of transistor (Q110) and electrolytic capacitor (C113) can change depending

on the models. Be sure to check the reference numbers on schematic diagram before starting the discharging work.

15

C113

Short with tweezers.

Fig-2-2

C113

%

*

VSS

VDD

MICROCOMPUTER

2-3. Confirmation of soldering state of MICROCOMPUTER

Check the soldering state of the MICROCOMPUTER in addition to the above described procedures. Be sure to exchange the MICROCOMPUTER after surely confirming that the trouble is not caused by poor soldering but the MICROCOMPUTER itself.

– 6 –

ELECTRICAL PARTS LIST (CX – NR11)

! = ! SAFTY PARTS C = Components marked

UNIT-NAME ! C REF-NO PARTS-NO PARTS-NAME SUFFIX&MODEL

CX-NR11 EZSC1 FRONT O C 0108 87-010-785-080 C-CAP,U 0.015-25 K B GRM a FRONT O C 0153 87-010-787-080 C-CAP,U 0.022-25 K B a FRONT O C 0154 87-010-246-040 CAP,E 47-35 M 11L SME a FRONT O C 0155 87-010-404-040 CAP,E 4.7-50 M 11L SME a FRONT O C 0156 87-010-404-040 CAP,E 4.7-50 M 11L SME a FRONT O C 0301 87-012-278-080 C-CAP,U 2200P-50 K B a FRONT O C 0351 87-A10-353-080 C-CAP,U 0.22-10 K B a FRONT O C 0361 87-012-274-080 C-CAP,U 1000P-50 K B a FRONT O C 0362 87-012-274-080 C-CAP,U 1000P-50 K B a FRONT O C 0371 87-012-274-080 C-CAP,U 1000P-50 K B a

FRONT O C 0372 87-012-274-080 C-CAP,U 1000P-50 K B a FRONT O C 0601 87-010-382-040 CAP,E 22-25 M 11L SME a FRONT O C 0801 87-A10-353-080 C-CAP,U 0.22-10 K B a FRONT O C 0803 87-012-280-080 C-CAP,U 3300P-50 K B a FRONT O C 0804 87-A10-592-080 C-CAP,S 0.015-50 J B a FRONT O C 0806 87-012-273-080 C-CAP,U 820P-50 K B a FRONT O C 0808 87-010-544-040 CAP,E 0.1-50 M 11L SME a FRONT O C 0809 87-010-404-040 CAP,E 4.7-50 M 11L SME a FRONT O C 0810 87-010-759-080 C-CAP,U 0.1-25 Z F a FRONT O C 0811 87-A12-052-080 C-CAP,S 0.033-25 J B a

CX-NR11 EZSC1 FRONT O C 0812 87-012-285-080 C-CAP,U 8200P-50 K B GRM a FRONT O C 0901 87-012-195-080 C-CAP,U 100P-50 J CH a FRONT O C 0902 87-012-195-080 C-CAP,U 100P-50 J CH a FRONT O C 0903 87-012-195-080 C-CAP,U 100P-50 J CH a FRONT O C 0904 87-012-195-080 C-CAP,U 100P-50 J CH a FRONT O C 0905 87-012-195-080 C-CAP,U 100P-50 J CH a FRONT O C 0906 87-012-195-080 C-CAP,U 100P-50 J CH a FRONT O C 0907 87-012-195-080 C-CAP,U 100P-50 J CH a FRONT O C 0908 87-012-195-080 C-CAP,U 100P-50 J CH a FRONT O C 0909 87-012-195-080 C-CAP,U 100P-50 J CH a

FRONT O C 0910 87-012-195-080 C-CAP,U 100P-50 J CH a FRONT O C 0911 87-012-274-080 C-CAP,U 1000P-50 K B a FRONT O C 0912 87-010-759-080 C-CAP,U 0.1-25 Z F a FRONT O C 0913 87-A10-189-040 CAP,E 220-10 M 5L a FRONT O C 0915 87-010-759-080 C-CAP,U 0.1-25 Z F a FRONT O C 0916 87-010-759-080 C-CAP,U 0.1-25 Z F a FRONT O C 0917 87-010-759-080 C-CAP,U 0.1-25 Z F a FRONT O C 0919 87-012-286-080 C-CAP,U 0.01-25 K B a FRONT O C 0920 87-010-829-080 C-CAP,U 0.047-16 Z F a FRONT O C 0921 87-012-282-080 C-CAP,U 4700P-50 K B a

CX-NR11 EZSC1 FRONT O C 0922 87-012-195-080 C-CAP,U 100P-50 J CH a FRONT O C 0923 87-016-116-080 C-CAP,U 0.015-25 J B CB a FRONT O C 0924 87-016-116-080 C-CAP,U 0.015-25 J B CB a FRONT O C 0925 87-016-116-080 C-CAP,U 0.015-25 J B CB a FRONT O C 0931 87-012-195-080 C-CAP,U 100P-50 J CH a FRONT O C 0932 87-012-195-080 C-CAP,U 100P-50 J CH a FRONT O C 0951 87-012-172-080 C-CAP,U 10P-50 D CH a FRONT O C 0952 87-010-854-080 C-CAP,S 560P-50 J CH a FRONT O C 0953 87-012-349-080 C-CAP,S 1000P-50 J CH GRM a FRONT O C 0961 87-010-391-040 CAP,E 10-35 M 11L SME a

FRONT O C 0962 87-012-336-080 C-CAP,U 330P-50 J SL a FRONT O C 0963 87-010-759-080 C-CAP,U 0.1-25 Z F a FRONT O CN 0103 87-099-013-010 CONN,11P V BLK 6216 a FRONT O CN 0701 87-099-720-010 CONN,30P BLK TYK-B(P) a FRONT O CN 0731 87-099-196-010 CONN,8P V BLK 6216 a FRONT S D 0103 87-020-465-080 DIODE,1SS133 a FRONT S D 0104 87-020-465-080 DIODE,1SS133 a FRONT S D 0301 87-A40-234-080 ZENER,MTZJ5.6A a FRONT S D 0302 87-020-465-080 DIODE,1SS133 a FRONT S D 0601 87-A40-269-080 C-DIODE,MC2836 a

CX-NR11 EZSC1 FRONT S D 0801 87-020-465-080 DIODE,1SS133 a FRONT S D 0983 87-020-465-080 DIODE,1SS133 a FRONT S D 0991 87-020-465-080 DIODE,1SS133 a FRONT O FC 0101 88-911-101-110 FF-CABLE,11P 1.25 100MM a FRONT O FC 0731 88-908-301-110 FF-CABLE,8P 1.25 300MM a FRONT O FL 0201 8C-NF9-615-010 FL,HUA-13SS09T a FRONT S IC 0901 8C-NF9-611-030 C-IC,UPD780228GF-089-3BA a FRONT S IC 0961 87-A21-831-010 IC,SPS-442-1-F1 a FRONT O L 0951 87-A50-655-010 COIL,CLK 4.19MHZ (TOKO)7KLY a FRONT S Q 0102 87-A30-076-080 C-TR,2SC3052F a

FRONT S Q 0104 87-A30-538-040 C-TR,SRA2202S a FRONT S Q 0301 87-A30-494-080 TR,2SA1980G a FRONT S Q 0302 87-A30-076-080 C-TR,2SC3052F a FRONT S Q 0303 87-A30-076-080 C-TR,2SC3052F a FRONT S Q 0601 87-A30-495-080 TR,2SA1981Y a FRONT S Q 0602 87-A30-495-080 TR,2SA1981Y a FRONT S Q 0603 87-A30-200-080 TR,2SA1585SR a FRONT S Q 0801 87-A30-076-080 C-TR,2SC3052F a FRONT S Q 0802 87-A30-075-080 C-TR,2SA1235F a FRONT S Q 0803 87-A30-076-080 C-TR,2SC3052F a

All components used on this model at the production line are shown in this service manual. However, please note that not all components will be available as spare parts for after-sales service. Components marked S and O are designated as spare parts for service and will be stocked at the spare parts centers. Components marked X and R are not designated as spare parts for after sales service, and will not be stocked at the spare parts centers.

– 7 –

! = ! SAFTY PARTS C = Components marked

All components used on this model at the production line are shown in this service manual. However, please note that not all components will be available as spare parts for after-sales service. Components marked S and O are designated as spare parts for service and will be stocked at the spare parts centers. Components marked X and R are not designated as spare parts for after sales service, and will not be stocked at the spare parts centers.

UNIT-NAME ! C REF-NO PARTS-NO PARTS-NAME SUFFIX&MODEL

CX-NR11 EZSC1 FRONT S Q 0804 87-A30-076-080 C-TR,2SC3052F a FRONT S Q 0805 87-A30-076-080 C-TR,2SC3052F a FRONT S Q 0901 87-A30-538-040 C-TR,SRA2202S a FRONT X R 0109 88-108-224-080 C-RES,U 220K-1/16W J a FRONT X R 0110 88-108-153-080 C-RES,U 15K-1/16W J a FRONT X R 0111 88-108-333-080 C-RES,U 33K-1/16W J a FRONT X R 0112 88-108-224-080 C-RES,U 220K-1/16W J a FRONT X R 0114 88-108-103-080 C-RES,U 10K-1/16W J a FRONT X R 0115 88-108-333-080 C-RES,U 33K-1/16W J a FRONT X R 0116 88-108-124-080 C-RES,U 120K-1/16W J a

FRONT X R 0151 88-100-000-010 PLATING-JW, 0.58 SN95 a FRONT X R 0152 88-100-000-010 PLATING-JW, 0.58 SN95 a FRONT X R 0153 88-128-821-080 C-RES, 820-1/8W J a FRONT X R 0154 88-128-821-080 C-RES, 820-1/8W J a FRONT X R 0155 88-108-332-080 C-RES,U 3.3K-1/16W J a FRONT X R 0156 88-108-332-080 C-RES,U 3.3K-1/16W J a FRONT X R 0161 88-108-000-080 C-JUMPER,U a FRONT X R 0162 88-108-000-080 C-JUMPER,U a FRONT X R 0163 88-108-000-080 C-JUMPER,U a FRONT X R 0164 88-108-000-080 C-JUMPER,U a

CX-NR11 EZSC1 FRONT X R 0165 88-108-000-080 C-JUMPER,U a FRONT X R 0166 88-108-000-080 C-JUMPER,U a FRONT X R 0301 88-108-104-080 C-RES,U 100K-1/16W J a FRONT X R 0302 88-108-472-080 C-RES,U 4.7K-1/16W J a FRONT X R 0303 88-108-153-080 C-RES,U 15K-1/16W J a FRONT X R 0304 88-108-102-080 C-RES,U 1K-1/16W J a FRONT X R 0306 88-108-471-080 C-RES,U 470-1/16W J a FRONT X R 0321 88-108-103-080 C-RES,U 10K-1/16W J a FRONT X R 0322 88-108-102-080 C-RES,U 1K-1/16W J a FRONT X R 0323 88-108-821-080 C-RES,U 820-1/16W J a

FRONT X R 0324 88-108-102-080 C-RES,U 1K-1/16W J a FRONT X R 0325 88-108-122-080 C-RES,U 1.2K-1/16W J a FRONT X R 0326 88-121-122-080 RES,1.2K-1/8W J a FRONT X R 0327 88-108-182-080 C-RES,U 1.8K-1/16W J a FRONT X R 0328 88-121-182-080 RES,1.8K-1/8W J a FRONT X R 0329 88-108-272-080 C-RES,U 2.7K-1/16W J a FRONT X R 0330 88-108-332-080 C-RES,U 3.3K-1/16W J a FRONT X R 0331 88-121-472-080 RES,4.7K-1/8W J a FRONT X R 0332 88-108-682-080 C-RES,U 6.8K-1/16W J a FRONT X R 0333 88-108-103-080 C-RES,U 10K-1/16W J a

CX-NR11 EZSC1 FRONT X R 0334 88-108-183-080 C-RES,U 18K-1/16W J a FRONT X R 0335 88-108-473-080 C-RES,U 47K-1/16W J a FRONT X R 0341 88-108-103-080 C-RES,U 10K-1/16W J a FRONT X R 0342 88-108-102-080 C-RES,U 1K-1/16W J a FRONT X R 0343 88-108-821-080 C-RES,U 820-1/16W J a FRONT X R 0344 88-108-102-080 C-RES,U 1K-1/16W J a FRONT X R 0345 88-108-122-080 C-RES,U 1.2K-1/16W J a FRONT X R 0346 88-108-122-080 C-RES,U 1.2K-1/16W J a FRONT X R 0347 88-108-182-080 C-RES,U 1.8K-1/16W J a FRONT X R 0348 88-108-182-080 C-RES,U 1.8K-1/16W J a

FRONT X R 0349 88-108-272-080 C-RES,U 2.7K-1/16W J a FRONT X R 0350 88-108-332-080 C-RES,U 3.3K-1/16W J a FRONT X R 0351 88-108-472-080 C-RES,U 4.7K-1/16W J a FRONT X R 0361 88-108-103-080 C-RES,U 10K-1/16W J a FRONT X R 0362 88-108-103-080 C-RES,U 10K-1/16W J a FRONT X R 0363 88-108-100-080 C-RES,U 10-1/16W J a FRONT X R 0364 88-108-100-080 C-RES,U 10-1/16W J a FRONT X R 0371 88-108-103-080 C-RES,U 10K-1/16W J a FRONT X R 0372 88-108-103-080 C-RES,U 10K-1/16W J a FRONT X R 0373 88-108-100-080 C-RES,U 10-1/16W J a

CX-NR11 EZSC1 FRONT X R 0374 88-108-100-080 C-RES,U 10-1/16W J a FRONT X R 0601 88-108-103-080 C-RES,U 10K-1/16W J a FRONT X R 0602 88-108-222-080 C-RES,U 2.2K-1/16W J a FRONT X R 0603 88-108-103-080 C-RES,U 10K-1/16W J a FRONT X R 0604 88-108-222-080 C-RES,U 2.2K-1/16W J a FRONT X R 0605 88-108-103-080 C-RES,U 10K-1/16W J a FRONT X R 0606 88-108-102-080 C-RES,U 1K-1/16W J a FRONT X R 0607 88-108-000-080 C-JUMPER,U a FRONT X R 0611 88-108-473-080 C-RES,U 47K-1/16W J a FRONT X R 0612 88-108-473-080 C-RES,U 47K-1/16W J a

FRONT X R 0613 88-108-473-080 C-RES,U 47K-1/16W J a FRONT X R 0614 88-108-473-080 C-RES,U 47K-1/16W J a FRONT X R 0615 88-108-473-080 C-RES,U 47K-1/16W J a FRONT X R 0617 88-108-473-080 C-RES,U 47K-1/16W J a FRONT X R 0618 88-108-473-080 C-RES,U 47K-1/16W J a FRONT X R 0701 88-108-102-080 C-RES,U 1K-1/16W J a FRONT X R 0702 88-128-102-080 C-RES, 1K-1/8W J a FRONT X R 0703 88-108-102-080 C-RES,U 1K-1/16W J a FRONT X R 0704 88-108-102-080 C-RES,U 1K-1/16W J a FRONT X R 0705 88-108-102-080 C-RES,U 1K-1/16W J a

– 8 –

! = ! SAFTY PARTS C = Components marked

All components used on this model at the production line are shown in this service manual. However, please note that not all components will be available as spare parts for after-sales service. Components marked S and O are designated as spare parts for service and will be stocked at the spare parts centers. Components marked X and R are not designated as spare parts for after sales service, and will not be stocked at the spare parts centers.

UNIT-NAME ! C REF-NO PARTS-NO PARTS-NAME SUFFIX&MODEL

CX-NR11 EZSC1 FRONT X R 0706 88-108-102-080 C-RES,U 1K-1/16W J a FRONT X R 0707 88-108-102-080 C-RES,U 1K-1/16W J a FRONT X R 0708 88-121-102-080 RES,1K-1/8W J a FRONT X R 0709 88-108-101-080 C-RES,U 100-1/16W J a FRONT X R 0710 88-128-101-080 C-RES, 100-1/8W J a FRONT X R 0711 88-108-101-080 C-RES,U 100-1/16W J a FRONT X R 0712 88-108-101-080 C-RES,U 100-1/16W J a FRONT X R 0719 88-108-100-080 C-RES,U 10-1/16W J a FRONT X R 0721 88-108-103-080 C-RES,U 10K-1/16W J a FRONT X R 0730 88-108-102-080 C-RES,U 1K-1/16W J a

FRONT X R 0732 88-108-101-080 C-RES,U 100-1/16W J a FRONT X R 0733 88-108-101-080 C-RES,U 100-1/16W J a FRONT X R 0734 88-108-102-080 C-RES,U 1K-1/16W J a FRONT X R 0735 88-108-102-080 C-RES,U 1K-1/16W J a FRONT X R 0740 88-108-102-080 C-RES,U 1K-1/16W J a FRONT X R 0741 88-108-101-080 C-RES,U 100-1/16W J a FRONT X R 0742 88-108-102-080 C-RES,U 1K-1/16W J a FRONT X R 0743 88-108-474-080 C-RES,U 470K-1/16W J a FRONT X R 0744 88-108-823-080 C-RES,U 82K-1/16W J a FRONT X R 0745 88-108-104-080 C-RES,U 100K-1/16W J a

CX-NR11 EZSC1 FRONT X R 0749 88-108-474-080 C-RES,U 470K-1/16W J a FRONT X R 0803 88-108-102-080 C-RES,U 1K-1/16W J a FRONT X R 0804 88-108-224-080 C-RES,U 220K-1/16W J a FRONT X R 0805 88-108-273-080 C-RES,U 27K-1/16W J a FRONT X R 0806 88-108-562-080 C-RES,U 5.6K-1/16W J a FRONT X R 0807 88-108-000-080 C-JUMPER,U a FRONT X R 0808 88-121-101-080 RES,100-1/8W J a FRONT X R 0809 88-108-102-080 C-RES,U 1K-1/16W J a FRONT X R 0810 88-108-182-080 C-RES,U 1.8K-1/16W J a FRONT X R 0811 88-108-224-080 C-RES,U 220K-1/16W J a

FRONT X R 0813 88-108-224-080 C-RES,U 220K-1/16W J a FRONT X R 0815 88-108-272-080 C-RES,U 2.7K-1/16W J a FRONT X R 0816 88-108-104-080 C-RES,U 100K-1/16W J a FRONT X R 0818 88-108-224-080 C-RES,U 220K-1/16W J a FRONT X R 0819 88-108-222-080 C-RES,U 2.2K-1/16W J a FRONT X R 0820 88-108-101-080 C-RES,U 100-1/16W J a FRONT X R 0821 88-108-104-080 C-RES,U 100K-1/16W J a FRONT X R 0822 88-108-224-080 C-RES,U 220K-1/16W J a FRONT X R 0823 88-100-000-010 PLATING-JW, 0.58 SN95 a FRONT X R 0824 88-100-000-010 PLATING-JW, 0.58 SN95 a

CX-NR11 EZSC1 FRONT X R 0825 88-100-000-010 PLATING-JW, 0.58 SN95 a FRONT X R 0826 88-108-000-080 C-JUMPER,U a FRONT X R 0827 88-108-473-080 C-RES,U 47K-1/16W J a FRONT X R 0901 88-108-104-080 C-RES,U 100K-1/16W J a FRONT X R 0902 88-108-104-080 C-RES,U 100K-1/16W J a FRONT X R 0903 88-108-104-080 C-RES,U 100K-1/16W J a FRONT X R 0904 88-108-104-080 C-RES,U 100K-1/16W J a FRONT X R 0905 88-108-104-080 C-RES,U 100K-1/16W J a FRONT X R 0906 88-108-104-080 C-RES,U 100K-1/16W J a FRONT X R 0907 88-108-104-080 C-RES,U 100K-1/16W J a

FRONT X R 0908 88-108-104-080 C-RES,U 100K-1/16W J a FRONT X R 0909 88-108-104-080 C-RES,U 100K-1/16W J a FRONT X R 0910 88-108-104-080 C-RES,U 100K-1/16W J a FRONT X R 0911 88-108-104-080 C-RES,U 100K-1/16W J a FRONT X R 0912 88-108-104-080 C-RES,U 100K-1/16W J a FRONT X R 0913 88-108-104-080 C-RES,U 100K-1/16W J a FRONT X R 0914 88-108-104-080 C-RES,U 100K-1/16W J a FRONT X R 0915 88-108-104-080 C-RES,U 100K-1/16W J a FRONT X R 0916 88-108-104-080 C-RES,U 100K-1/16W J a FRONT X R 0917 88-108-104-080 C-RES,U 100K-1/16W J a

CX-NR11 EZSC1 FRONT X R 0918 88-108-104-080 C-RES,U 100K-1/16W J a FRONT X R 0919 88-108-104-080 C-RES,U 100K-1/16W J a FRONT X R 0920 88-108-104-080 C-RES,U 100K-1/16W J a FRONT X R 0921 88-108-104-080 C-RES,U 100K-1/16W J a FRONT X R 0922 88-108-104-080 C-RES,U 100K-1/16W J a FRONT X R 0923 88-108-104-080 C-RES,U 100K-1/16W J a FRONT X R 0924 88-108-104-080 C-RES,U 100K-1/16W J a FRONT X R 0925 88-108-104-080 C-RES,U 100K-1/16W J a FRONT X R 0926 88-108-104-080 C-RES,U 100K-1/16W J a FRONT X R 0927 88-108-104-080 C-RES,U 100K-1/16W J a

FRONT X R 0928 88-108-104-080 C-RES,U 100K-1/16W J a FRONT X R 0929 88-108-104-080 C-RES,U 100K-1/16W J a FRONT X R 0930 88-108-104-080 C-RES,U 100K-1/16W J a FRONT X R 0931 88-108-104-080 C-RES,U 100K-1/16W J a FRONT X R 0932 88-108-104-080 C-RES,U 100K-1/16W J a FRONT X R 0933 88-121-104-080 RES,100K-1/8W J a FRONT X R 0934 88-108-683-080 C-RES,U 68K-1/16W J a FRONT X R 0935 88-108-683-080 C-RES,U 68K-1/16W J a FRONT X R 0936 88-108-104-080 C-RES,U 100K-1/16W J a FRONT X R 0937 88-128-472-080 C-RES, 4.7K-1/8W J a

– 9 –

! = ! SAFTY PARTS C = Components marked

All components used on this model at the production line are shown in this service manual. However, please note that not all components will be available as spare parts for after-sales service. Components marked S and O are designated as spare parts for service and will be stocked at the spare parts centers. Components marked X and R are not designated as spare parts for after sales service, and will not be stocked at the spare parts centers.

UNIT-NAME ! C REF-NO PARTS-NO PARTS-NAME SUFFIX&MODEL

CX-NR11 EZSC1 FRONT X R 0938 88-108-472-080 C-RES,U 4.7K-1/16W J a FRONT X R 0939 88-108-472-080 C-RES,U 4.7K-1/16W J a FRONT X R 0940 88-108-104-080 C-RES,U 100K-1/16W J a FRONT X R 0941 88-108-104-080 C-RES,U 100K-1/16W J a FRONT X R 0942 88-108-103-080 C-RES,U 10K-1/16W J a FRONT X R 0943 88-121-472-080 RES,4.7K-1/8W J a FRONT X R 0946 88-108-000-080 C-JUMPER,U a FRONT X R 0947 88-108-104-080 C-RES,U 100K-1/16W J a FRONT X R 0948 88-121-104-080 RES,100K-1/8W J a FRONT X R 0951 88-108-102-080 C-RES,U 1K-1/16W J a

FRONT X R 0955 88-108-104-080 C-RES,U 100K-1/16W J a FRONT X R 0956 88-108-104-080 C-RES,U 100K-1/16W J a FRONT X R 0957 88-108-104-080 C-RES,U 100K-1/16W J a FRONT X R 0958 88-108-103-080 C-RES,U 10K-1/16W J a FRONT X R 0959 88-108-103-080 C-RES,U 10K-1/16W J a FRONT X R 0961 88-121-181-080 RES,180-1/8W J a FRONT X R 0963 88-108-563-080 C-RES,U 56K-1/16W J a FRONT X R 0969 88-108-103-080 C-RES,U 10K-1/16W J a FRONT X R 0981 88-108-103-080 C-RES,U 10K-1/16W J a FRONT X R 0982 88-108-103-080 C-RES,U 10K-1/16W J a

CX-NR11 EZSC1 FRONT X R 0983 88-108-103-080 C-RES,U 10K-1/16W J a FRONT X R 0984 88-108-103-080 C-RES,U 10K-1/16W J a FRONT X R 0985 88-121-103-080 RES,10K-1/8W J a FRONT X R 0986 88-121-103-080 RES,10K-1/8W J a FRONT X R 0987 88-108-103-080 C-RES,U 10K-1/16W J a FRONT X R 0988 88-108-103-080 C-RES,U 10K-1/16W J a FRONT X R 0989 88-108-103-080 C-RES,U 10K-1/16W J a FRONT O S 0321 87-A90-164-080 SW,TACT SKQNAB(N) a FRONT O S 0322 87-A90-164-080 SW,TACT SKQNAB(N) a FRONT O S 0323 87-A90-164-080 SW,TACT SKQNAB(N) a

FRONT O S 0324 87-A90-164-080 SW,TACT SKQNAB(N) a FRONT O S 0325 87-A90-164-080 SW,TACT SKQNAB(N) a FRONT O S 0326 87-A90-164-080 SW,TACT SKQNAB(N) a FRONT O S 0327 87-A90-164-080 SW,TACT SKQNAB(N) a FRONT O S 0328 87-A90-164-080 SW,TACT SKQNAB(N) a FRONT O S 0329 87-A90-164-080 SW,TACT SKQNAB(N) a FRONT O S 0330 87-A90-164-080 SW,TACT SKQNAB(N) a FRONT O S 0331 87-A90-164-080 SW,TACT SKQNAB(N) a FRONT O S 0332 87-A90-164-080 SW,TACT SKQNAB(N) a FRONT O S 0333 87-A90-164-080 SW,TACT SKQNAB(N) a

CX-NR11 EZSC1 FRONT O S 0334 87-A90-164-080 SW,TACT SKQNAB(N) a FRONT O S 0335 87-A90-164-080 SW,TACT SKQNAB(N) a FRONT O S 0341 87-A90-164-080 SW,TACT SKQNAB(N) a FRONT O S 0342 87-A90-164-080 SW,TACT SKQNAB(N) a FRONT O S 0343 87-A90-164-080 SW,TACT SKQNAB(N) a FRONT O S 0344 87-A90-164-080 SW,TACT SKQNAB(N) a FRONT O S 0345 87-A90-164-080 SW,TACT SKQNAB(N) a FRONT O S 0346 87-A90-164-080 SW,TACT SKQNAB(N) a FRONT O S 0347 87-A90-164-080 SW,TACT SKQNAB(N) a FRONT O S 0348 87-A90-164-080 SW,TACT SKQNAB(N) a

FRONT O S 0350 87-A90-164-080 SW,TACT SKQNAB(N) a FRONT O S 0351 87-A90-164-080 SW,TACT SKQNAB(N) a FRONT O S 0361 87-A92-370-010 SW,RTRY RE012307PVB30F a FRONT O S 0371 87-A92-371-010 SW,RTRY RE0123PVB30F a HP O C 0223 87-010-176-080 C-CAP,S 680P-50 J SL a HP O C 0224 87-010-176-080 C-CAP,S 680P-50 J SL a HP O J 0201 87-A60-420-010 JACK,3.5 ST (MSC) a HP X R 0243 88-130-331-080 RES,330-1/4W J a HP X R 0244 88-130-331-080 RES,330-1/4W J a HP X R 0265 88-128-222-080 C-RES, 2.2K-1/8W J a

CX-NR11 EZSC1 HP X R 0266 88-128-222-080 C-RES, 2.2K-1/8W J a HP O WH 0201 87-A90-459-010 HLDR,WIRE 2.5-5P a MAIN O C 0003 87-010-759-080 C-CAP,U 0.1-25 Z F a MAIN O C 0004 87-010-759-080 C-CAP,U 0.1-25 Z F a MAIN O C 0005 87-010-759-080 C-CAP,U 0.1-25 Z F a MAIN O C 0006 87-010-759-080 C-CAP,U 0.1-25 Z F a MAIN O C 0013 87-012-282-080 C-CAP,U 4700P-50 K B a MAIN O C 0014 87-010-260-040 CAP,E 47-25 M 11L SME a MAIN O C 0018 87-012-286-080 C-CAP,U 0.01-25 K B a MAIN O C 0019 87-A12-442-000 CAP,E 3300-25 M 85 IV LELON a

MAIN O C 0021 87-010-388-080 CAP,E 1000-25 M SME a MAIN O C 0022 87-010-388-080 CAP,E 1000-25 M SME a MAIN O C 0025 87-010-384-080 CAP,E 100-25 M 11L SME a MAIN O C 0026 87-010-384-080 CAP,E 100-25 M 11L SME a MAIN O C 0027 87-010-384-080 CAP,E 100-25 M 11L SME a MAIN O C 0028 87-010-384-080 CAP,E 100-25 M 11L SME a MAIN O C 0030 87-010-247-080 CAP,E 100-50 M SME a MAIN O C 0031 87-A12-317-080 C-CAP,U 0.1-50 Z F a MAIN O C 0034 87-010-260-040 CAP,E 47-25 M 11L SME a MAIN O C 0035 87-010-405-080 CAP,E 10-50 M 11L SME a

– 10 –

! = ! SAFTY PARTS C = Components marked

All components used on this model at the production line are shown in this service manual. However, please note that not all components will be available as spare parts for after-sales service. Components marked S and O are designated as spare parts for service and will be stocked at the spare parts centers. Components marked X and R are not designated as spare parts for after sales service, and will not be stocked at the spare parts centers.

UNIT-NAME ! C REF-NO PARTS-NO PARTS-NAME SUFFIX&MODEL

CX-NR11 EZSC1 MAIN O C 0036 87-010-260-040 CAP,E 47-25 M 11L SME a MAIN O C 0060 87-010-403-080 CAP,E 3.3-50 M 11L SME a MAIN O C 0061 87-010-260-040 CAP,E 47-25 M 11L SME a MAIN O C 0083 87-010-385-080 CAP,E 220-25 M SME a MAIN O C 0097 87-010-831-080 C-CAP,U 0.1-16 Z F a MAIN O C 0099 87-010-831-080 C-CAP,U 0.1-16 Z F a MAIN O C 0101 87-012-278-080 C-CAP,U 2200P-50 K B a MAIN O C 0102 87-012-278-080 C-CAP,U 2200P-50 K B a MAIN O C 0103 87-010-544-080 CAP,E 0.1-50 M 11L SME a MAIN O C 0104 87-010-544-080 CAP,E 0.1-50 M 11L SME a

MAIN O C 0107 87-010-405-080 CAP,E 10-50 M 11L SME a MAIN O C 0108 87-010-405-080 CAP,E 10-50 M 11L SME a MAIN O C 0109 87-012-199-080 C-CAP,U 220P-50 J CH a MAIN O C 0110 87-012-199-080 C-CAP,U 220P-50 J CH a MAIN O C 0111 87-010-383-080 CAP,E 33-25 M 11L SME a MAIN O C 0112 87-010-383-080 CAP,E 33-25 M 11L SME a MAIN O C 0113 87-A12-087-080 CAP,E 1-50 SMG a MAIN O C 0114 87-A12-087-080 CAP,E 1-50 SMG a MAIN O C 0115 87-A10-260-080 C-CAP,U 0.1-16 K B a MAIN O C 0117 87-012-368-080 C-CAP,S 0.1-50 Z F a

CX-NR11 EZSC1 MAIN O C 0118 87-012-368-080 C-CAP,S 0.1-50 Z F a MAIN O C 0119 87-012-286-080 C-CAP,U 0.01-25 K B a MAIN O C 0120 87-012-286-080 C-CAP,U 0.01-25 K B a MAIN O C 0123 87-010-177-080 C-CAP,S 820P-50 J SL C2012 a MAIN O C 0124 87-010-177-080 C-CAP,S 820P-50 J SL C2012 a MAIN O C 0125 87-012-188-080 C-CAP,U 47P-50 J CH a MAIN O C 0126 87-012-188-080 C-CAP,U 47P-50 J CH a MAIN O C 0133 87-012-282-080 C-CAP,U 4700P-50 K B a MAIN O C 0140 87-012-278-080 C-CAP,U 2200P-50 K B a MAIN O C 0225 87-012-368-080 C-CAP,S 0.1-50 Z F a

MAIN O C 0226 87-012-368-080 C-CAP,S 0.1-50 Z F a MAIN O C 0227 87-012-368-080 C-CAP,S 0.1-50 Z F a MAIN O C 0228 87-012-368-080 C-CAP,S 0.1-50 Z F a MAIN O C 0229 87-010-191-080 C-CAP,S 0.015-50 Z F GRM a MAIN O C 0230 87-010-191-080 C-CAP,S 0.015-50 Z F GRM a MAIN O C 0231 87-012-287-080 C-CAP,U 0.015-25 Z F a MAIN O C 0232 87-012-286-080 C-CAP,U 0.01-25 K B a MAIN O C 0241 87-010-831-080 C-CAP,U 0.1-16 Z F a MAIN O C 0301 87-012-275-080 C-CAP,U 1200P-50 K B GRM a MAIN O C 0302 87-012-275-080 C-CAP,U 1200P-50 K B GRM a

CX-NR11 EZSC1 MAIN O C 0303 87-012-275-080 C-CAP,U 1200P-50 K B GRM a MAIN O C 0304 87-012-275-080 C-CAP,U 1200P-50 K B GRM a MAIN O C 0305 87-A10-039-080 C-CAP,U 470P-50 J CH a MAIN O C 0310 87-012-274-080 C-CAP,U 1000P-50 K B a MAIN O C 0363 87-010-759-080 C-CAP,U 0.1-25 Z F a MAIN O C 0451 87-010-759-080 C-CAP,U 0.1-25 Z F a MAIN O C 0452 87-010-406-080 CAP,E 22-50 M 11L SME a MAIN O C 0453 87-012-279-080 C-CAP,U 2700P-50 K B GRM a MAIN O C 0454 87-012-279-080 C-CAP,U 2700P-50 K B GRM a MAIN O C 0455 87-012-279-080 C-CAP,U 2700P-50 K B GRM a

MAIN O C 0456 87-012-286-080 C-CAP,U 0.01-25 K B a MAIN X C 0457 88-708-730-810 CAP,M 5600P-100 J a MAIN O C 0458 87-012-278-080 C-CAP,U 2200P-50 K B a MAIN O C 0459 87-012-271-080 C-CAP,U 560P-50 K B a MAIN O C 0460 87-A12-317-080 C-CAP,U 0.1-50 Z F a MAIN O C 0461 87-012-158-080 C-CAP,S 390P-50 J CH GRM a MAIN O C 0462 87-012-158-080 C-CAP,S 390P-50 J CH GRM a MAIN O C 0463 87-010-759-080 C-CAP,U 0.1-25 Z F a MAIN O C 0464 87-012-278-080 C-CAP,U 2200P-50 K B a MAIN O C 0465 87-012-286-080 C-CAP,U 0.01-25 K B a

CX-NR11 EZSC1 MAIN O C 0601 87-012-188-080 C-CAP,U 47P-50 J CH a MAIN O C 0602 87-012-188-080 C-CAP,U 47P-50 J CH a MAIN O C 0603 87-010-263-080 CAP,E 100-10 M 11L SME a MAIN O C 0604 87-010-263-080 CAP,E 100-10 M 11L SME a MAIN X C 0605 88-700-740-080 CAP,M 6800P-50 J a MAIN X C 0606 88-700-740-080 CAP,M 6800P-50 J a MAIN O C 0607 87-A10-039-080 C-CAP,U 470P-50 J CH a MAIN O C 0608 87-A10-039-080 C-CAP,U 470P-50 J CH a MAIN O C 0609 87-010-401-080 CAP,E 1-50 M 11L SME a MAIN O C 0610 87-010-401-080 CAP,E 1-50 M 11L SME a

MAIN O C 0611 87-A12-790-080 C-CAP,U 560P-50 J CH a MAIN O C 0612 87-A12-790-080 C-CAP,U 560P-50 J CH a MAIN O C 0613 87-012-274-080 C-CAP,U 1000P-50 K B a MAIN O C 0614 87-012-274-080 C-CAP,U 1000P-50 K B a MAIN O C 0615 87-010-545-080 CAP,E 0.22-50 M 11L SME a MAIN O C 0616 87-010-545-080 CAP,E 0.22-50 M 11L SME a MAIN O C 0617 87-010-545-080 CAP,E 0.22-50 M 11L SME a MAIN O C 0618 87-010-545-080 CAP,E 0.22-50 M 11L SME a MAIN O C 0625 87-012-198-080 C-CAP,U 180P-50 J CH a MAIN O C 0626 87-012-198-080 C-CAP,U 180P-50 J CH a

– 11 –

! = ! SAFTY PARTS C = Components marked

All components used on this model at the production line are shown in this service manual. However, please note that not all components will be available as spare parts for after-sales service. Components marked S and O are designated as spare parts for service and will be stocked at the spare parts centers. Components marked X and R are not designated as spare parts for after sales service, and will not be stocked at the spare parts centers.

UNIT-NAME ! C REF-NO PARTS-NO PARTS-NAME SUFFIX&MODEL

CX-NR11 EZSC1 MAIN O C 0627 87-012-284-080 C-CAP,U 6800P-50 K B GRM a MAIN O C 0628 87-012-284-080 C-CAP,U 6800P-50 K B GRM a MAIN O C 0629 87-012-286-080 C-CAP,U 0.01-25 K B a MAIN O C 0630 87-012-286-080 C-CAP,U 0.01-25 K B a MAIN O C 0631 87-012-278-080 C-CAP,U 2200P-50 K B a MAIN O C 0632 87-012-278-080 C-CAP,U 2200P-50 K B a MAIN O C 0641 87-010-401-080 CAP,E 1-50 M 11L SME a MAIN O C 0642 87-010-401-080 CAP,E 1-50 M 11L SME a MAIN O C 0651 87-010-248-080 CAP,E 220-10 M 11L SME a MAIN O C 0652 87-010-260-080 CAP,E 47-25 M 11L SME a

MAIN O C 0655 87-010-404-080 CAP,E 4.7-50 M 11L SME a MAIN O C 0656 87-010-784-080 C-CAP,U 0.012-25 K B a MAIN O C 0663 87-010-759-080 C-CAP,U 0.1-25 Z F a MAIN O C 0664 87-010-759-080 C-CAP,U 0.1-25 Z F a MAIN O C 0665 87-A10-504-080 C-CAP,U 0.047-16 K B a MAIN O C 0666 87-A10-504-080 C-CAP,U 0.047-16 K B a MAIN O C 0677 87-012-286-080 C-CAP,U 0.01-25 K B a MAIN O C 0771 87-010-263-080 CAP,E 100-10 M 11L SME a MAIN O C 0772 87-012-286-080 C-CAP,U 0.01-25 K B a MAIN X C 0781 88-108-000-080 C-JUMPER,U a

CX-NR11 EZSC1 MAIN O C 0782 87-012-286-080 C-CAP,U 0.01-25 K B a MAIN O C 0783 87-012-286-080 C-CAP,U 0.01-25 K B a MAIN O C 0784 87-012-286-080 C-CAP,U 0.01-25 K B a MAIN O C 0785 87-012-286-080 C-CAP,U 0.01-25 K B a MAIN O C 0786 87-012-286-080 C-CAP,U 0.01-25 K B a MAIN O C 0788 87-012-167-080 C-CAP,U 5P-50 C CH a MAIN O C 0789 87-016-118-080 C-CAP,U 0.022-25 J B GRM a MAIN O C 0790 87-016-118-080 C-CAP,U 0.022-25 J B GRM a MAIN O C 0791 87-010-759-080 C-CAP,U 0.1-25 Z F a MAIN O C 0792 87-012-286-080 C-CAP,U 0.01-25 K B a

MAIN O C 0793 87-010-404-080 CAP,E 4.7-50 M 11L SME a MAIN O C 0795 87-012-286-080 C-CAP,U 0.01-25 K B a MAIN O C 0796 87-012-286-080 C-CAP,U 0.01-25 K B a MAIN O C 0797 87-010-405-080 CAP,E 10-50 M 11L SME a MAIN O C 0798 87-012-286-080 C-CAP,U 0.01-25 K B a MAIN O C 0799 87-010-265-080 CAP,E 33-16 M 11L SME a MAIN O C 0800 87-010-829-080 C-CAP,U 0.047-16 Z F a MAIN O C 0801 87-010-403-080 CAP,E 3.3-50 M 11L SME a MAIN O C 0802 87-010-829-080 C-CAP,U 0.047-16 Z F a MAIN O C 0803 87-010-787-080 C-CAP,U 0.022-25 K B a

CX-NR11 EZSC1 MAIN O C 0804 87-010-263-080 CAP,E 100-10 M 11L SME a MAIN O C 0807 87-010-400-080 CAP,E 0.47-50 M 11L SME a MAIN O C 0808 87-010-401-080 CAP,E 1-50 M 11L SME a MAIN O C 0809 87-010-401-080 CAP,E 1-50 M 11L SME a MAIN O C 0810 87-010-759-080 C-CAP,U 0.1-25 Z F a MAIN O C 0814 87-012-286-080 C-CAP,U 0.01-25 K B a MAIN O C 0815 87-010-400-080 CAP,E 0.47-50 M 11L SME a MAIN O C 0816 87-010-400-080 CAP,E 0.47-50 M 11L SME a MAIN O C 0818 87-012-276-080 C-CAP,U 1500P-50 K B a MAIN O C 0821 87-010-405-080 CAP,E 10-50 M 11L SME a

MAIN X C 0822 88-108-000-080 C-JUMPER,U a MAIN O C 0823 87-012-349-080 C-CAP,S 1000P-50 J CH GRM a MAIN O C 0824 87-010-404-080 CAP,E 4.7-50 M 11L SME a MAIN O C 0825 87-010-596-080 C-CAP,S 0.047-16 K R C2012 a MAIN O C 0831 87-010-406-080 CAP,E 22-50 M 11L SME a MAIN O C 0842 87-012-286-080 C-CAP,U 0.01-25 K B a MAIN X C 0843 88-108-000-080 C-JUMPER,U a MAIN O C 0844 87-012-286-080 C-CAP,U 0.01-25 K B a MAIN X C 0845 88-108-000-080 C-JUMPER,U a MAIN X C 0846 88-108-000-080 C-JUMPER,U a

CX-NR11 EZSC1 MAIN X C 0847 88-108-000-080 C-JUMPER,U a MAIN X C 0848 88-108-000-080 C-JUMPER,U a MAIN X C 0849 88-108-000-080 C-JUMPER,U a MAIN O C 0850 87-010-260-080 CAP,E 47-25 M 11L SME a MAIN O C 0851 87-012-286-080 C-CAP,U 0.01-25 K B a MAIN O C 0852 87-012-286-080 C-CAP,U 0.01-25 K B a MAIN O C 0853 87-012-286-080 C-CAP,U 0.01-25 K B a MAIN O C 0859 87-010-759-080 C-CAP,U 0.1-25 Z F a MAIN O C 0860 87-012-286-080 C-CAP,U 0.01-25 K B a MAIN O C 0869 87-012-286-080 C-CAP,U 0.01-25 K B a

MAIN O C 0870 87-012-274-080 C-CAP,U 1000P-50 K B a MAIN O C 0871 87-012-199-080 C-CAP,U 220P-50 J CH a MAIN O C 0872 87-012-199-080 C-CAP,U 220P-50 J CH a MAIN O C 0873 87-A10-039-080 C-CAP,U 470P-50 J CH a MAIN O C 0874 87-010-405-080 CAP,E 10-50 M 11L SME a MAIN O C 0875 87-010-759-080 C-CAP,U 0.1-25 Z F a MAIN O C 0876 87-010-405-080 CAP,E 10-50 M 11L SME a MAIN O C 0877 87-012-286-080 C-CAP,U 0.01-25 K B a MAIN O C 0878 87-012-184-080 C-CAP,U 33P-50 J CH a MAIN O C 0879 87-012-180-080 C-CAP,U 22P-50 J CH a

– 12 –

! = ! SAFTY PARTS C = Components marked

All components used on this model at the production line are shown in this service manual. However, please note that not all components will be available as spare parts for after-sales service. Components marked S and O are designated as spare parts for service and will be stocked at the spare parts centers. Components marked X and R are not designated as spare parts for after sales service, and will not be stocked at the spare parts centers.

UNIT-NAME ! C REF-NO PARTS-NO PARTS-NAME SUFFIX&MODEL

CX-NR11 EZSC1 MAIN O C 0901 87-012-162-080 C-CAP,U 1P-50 C CH a MAIN O C 0902 87-012-165-080 C-CAP,U 3P-50 C CH a MAIN O C 0903 87-012-164-080 C-CAP,U 2P-50 C CH a MAIN O C 0904 86-ZA1-615-080 C-CAP,U 680P-25 J CH a MAIN O C 0905 87-012-162-080 C-CAP,U 1P-50 C CH a MAIN O C 0906 87-012-172-080 C-CAP,U 10P-50 D CH a MAIN O C 0907 87-012-166-080 C-CAP,U 4P-50 C CH a MAIN O C 0908 87-012-165-080 C-CAP,U 3P-50 C CH a MAIN O C 0909 86-ZA1-615-080 C-CAP,U 680P-25 J CH a MAIN O C 0910 87-012-164-080 C-CAP,U 2P-50 C CH a

MAIN O C 0911 87-012-166-080 C-CAP,U 4P-50 C CH a MAIN O C 0912 87-012-195-080 C-CAP,U 100P-50 J CH a MAIN O C 0913 86-ZA1-616-080 C-CAP,U 0.01-50 K B (MUR) a MAIN O C 0914 86-ZA1-616-080 C-CAP,U 0.01-50 K B (MUR) a MAIN O C 0915 86-ZA1-616-080 C-CAP,U 0.01-50 K B (MUR) a MAIN O C 0916 86-ZA1-616-080 C-CAP,U 0.01-50 K B (MUR) a MAIN O C 0917 87-012-178-080 C-CAP,U 18P-50 J CH a MAIN O C 0918 87-012-172-080 C-CAP,U 10P-50 D CH a MAIN O C 0919 87-012-184-080 C-CAP,U 33P-50 J CH a MAIN O C 0920 87-012-184-080 C-CAP,U 33P-50 J CH a

CX-NR11 EZSC1 MAIN O C 0921 87-012-180-080 C-CAP,U 22P-50 J CH a MAIN O C 0922 87-012-174-080 C-CAP,U 12P-50 J CH a MAIN O C 0923 86-ZA1-616-080 C-CAP,U 0.01-50 K B (MUR) a MAIN O C 0924 87-012-164-080 C-CAP,U 2P-50 C CH a MAIN O C 0925 87-012-164-080 C-CAP,U 2P-50 C CH a MAIN O C 0926 86-ZA1-616-080 C-CAP,U 0.01-50 K B (MUR) a MAIN O C 0931 87-A12-319-080 C-CAP,U 0.1-25 K B a MAIN O C 0940 87-012-286-080 C-CAP,U 0.01-25 K B a MAIN O C 0942 87-012-167-080 C-CAP,U 5P-50 C CH a MAIN O C 0947 87-012-286-080 C-CAP,U 0.01-25 K B a

MAIN O C 0948 87-A10-039-080 C-CAP,U 470P-50 J CH a MAIN O C 0952 87-012-286-080 C-CAP,U 0.01-25 K B a MAIN O C 0958 87-012-286-080 C-CAP,U 0.01-25 K B a MAIN O C 0959 87-010-759-080 C-CAP,U 0.1-25 Z F a MAIN O C 0960 87-010-759-080 C-CAP,U 0.1-25 Z F a MAIN O C 0962 87-010-401-080 CAP,E 1-50 M 11L SME a MAIN O C 0963 87-A12-319-080 C-CAP,U 0.1-25 K B a MAIN O C 0971 87-010-381-080 CAP,E 330-16 M SME a MAIN O C 0972 87-010-404-080 CAP,E 4.7-50 M 11L SME a MAIN O C 0973 87-012-286-080 C-CAP,U 0.01-25 K B a

CX-NR11 EZSC1 MAIN O C 0974 87-012-286-080 C-CAP,U 0.01-25 K B a MAIN O C 0979 87-012-195-080 C-CAP,U 100P-50 J CH a MAIN O C 0981 87-010-260-080 CAP,E 47-25 M 11L SME a MAIN O C 0982 87-010-759-080 C-CAP,U 0.1-25 Z F a MAIN O C 0983 87-012-286-080 C-CAP,U 0.01-25 K B a MAIN O C 0984 87-012-286-080 C-CAP,U 0.01-25 K B a MAIN O C 0985 87-012-195-080 C-CAP,U 100P-50 J CH a MAIN O C 0987 87-012-286-080 C-CAP,U 0.01-25 K B a MAIN O C 0989 87-012-286-080 C-CAP,U 0.01-25 K B a MAIN O C 0991 87-012-176-080 C-CAP,U 15P-50 J CH a

MAIN O C 0992 87-012-176-080 C-CAP,U 15P-50 J CH a MAIN O C 0993 87-012-274-080 C-CAP,U 1000P-50 K B a MAIN O C 0995 87-012-274-080 C-CAP,U 1000P-50 K B a MAIN O C 0997 87-010-759-080 C-CAP,U 0.1-25 Z F a MAIN O C 0998 87-010-260-080 CAP,E 47-25 M 11L SME a MAIN O C 0999 87-A11-155-080 CAP,TC U 0.01-16 Z F a MAIN O CF 0831 87-008-423-010 FLTR,CF SFE10.7MS3G-A a MAIN O CF 0832 82-785-747-010 CF,MS2 GHY,R a MAIN O CN 0301 87-A60-620-010 CONN,3P V 2MM JMT a MAIN O CN 0302 87-A60-625-010 CONN,8P V 2MM JMT a

CX-NR11 EZSC1 MAIN O CN 0601 87-099-719-010 CONN,30P H BLK TYK-B(X) a MAIN O CN 0602 87-099-194-010 CONN,6P V BLK 6216 a MAIN O CNA0301 8C-NF9-605-010 CONN ASSY,3P -PB a MAIN O CNA0302 8C-NF9-606-010 CONN ASSY,8P -RPB a MAIN S D 0003 87-A40-553-080 DIODE,1N4003 LES a MAIN S D 0004 87-A40-553-080 DIODE,1N4003 LES a MAIN S D 0005 87-A40-553-080 DIODE,1N4003 LES a MAIN S D 0006 87-A40-553-080 DIODE,1N4003 LES a MAIN S D 0007 87-A40-455-090 DIODE,RL203 GW a MAIN S D 0008 87-A40-455-090 DIODE,RL203 GW a

MAIN S D 0011 87-A40-270-080 C-DIODE,MC2838 a MAIN S D 0012 87-020-465-080 DIODE,1SS133 a MAIN S D 0013 87-A40-345-080 ZENER,MTZJ10C a MAIN S D 0025 87-A40-553-080 DIODE,1N4003 LES a MAIN S D 0026 87-A40-553-080 DIODE,1N4003 LES a MAIN S D 0027 87-A40-553-080 DIODE,1N4003 LES a MAIN S D 0028 87-A40-553-080 DIODE,1N4003 LES a MAIN S D 0029 87-A40-336-080 ZENER,MTZJ27D T-72 a MAIN S D 0033 87-020-465-080 DIODE,1SS133 a MAIN S D 0060 87-020-465-080 DIODE,1SS133 a

– 13 –

! = ! SAFTY PARTS C = Components marked

All components used on this model at the production line are shown in this service manual. However, please note that not all components will be available as spare parts for after-sales service. Components marked S and O are designated as spare parts for service and will be stocked at the spare parts centers. Components marked X and R are not designated as spare parts for after sales service, and will not be stocked at the spare parts centers.

UNIT-NAME ! C REF-NO PARTS-NO PARTS-NAME SUFFIX&MODEL

CX-NR11 EZSC1 MAIN S D 0063 87-A40-270-080 C-DIODE,MC2838 a MAIN S D 0064 87-A40-269-080 C-DIODE,MC2836 a MAIN S D 0092 87-A40-270-080 C-DIODE,MC2838 a MAIN S D 0101 87-A40-269-080 C-DIODE,MC2836 a MAIN S D 0103 87-020-465-080 DIODE,1SS133 a MAIN S D 0104 87-020-465-080 DIODE,1SS133 a MAIN S D 0105 87-A40-269-080 C-DIODE,MC2836 a MAIN S D 0106 87-A40-269-080 C-DIODE,MC2836 a MAIN S D 0107 87-A40-270-080 C-DIODE,MC2838 a MAIN S D 0108 87-A40-270-080 C-DIODE,MC2838 a

MAIN S D 0160 87-A40-270-080 C-DIODE,MC2838 a MAIN S D 0280 87-A40-269-080 C-DIODE,MC2836 a MAIN S D 0281 87-A40-270-080 C-DIODE,MC2838 a MAIN S D 0301 87-A40-269-080 C-DIODE,MC2836 a MAIN S D 0661 87-A40-438-080 ZENER,MTZJ4.7A a MAIN S D 0662 87-A40-438-080 ZENER,MTZJ4.7A a MAIN S D 0801 87-020-465-080 DIODE,1SS133 a MAIN S D 0803 87-020-465-080 DIODE,1SS133 a MAIN O D 0901 87-A41-048-040 C-VARI-CAP,HVM16-03 TL a MAIN O D 0902 87-A41-048-040 C-VARI-CAP,HVM16-03 TL a

CX-NR11 EZSC1 MAIN O D 0903 87-A41-048-040 C-VARI-CAP,HVM16-03 TL a MAIN S D 0942 87-A40-270-080 C-DIODE,MC2838 a MAIN S D 0944 87-020-465-080 DIODE,1SS133 a MAIN O D 0951 87-A40-799-040 C-VARI-CAP,KV1610S a MAIN S D 0991 87-017-149-080 ZENER,HZS6A2L a MAIN S D 0992 87-020-465-080 DIODE,1SS133 a MAIN S D 0994 87-020-465-080 DIODE,1SS133 a MAIN X FB 0601 88-118-000-080 C-JUMPER,S a MAIN X FB 0602 88-118-000-080 C-JUMPER,S a MAIN X FB 0603 88-100-000-010 PLATING-JW, 0.58 SN95 a

MAIN O FC 0602 88-906-251-110 FF-CABLE,6P 1.25 a MAIN S IC 0001 87-A21-364-010 IC,NJM7806FA(A) a MAIN S IC 0601 87-A22-236-040 C-IC,BD3881FV a MAIN S IC 0801 87-A22-060-010 IC,LA1845N-A a MAIN S IC 0861 87-A20-440-040 C-IC,BU1920FS a MAIN S IC 0991 87-A21-928-010 IC,LC72131D-N a MAIN O J 0203 87-A60-238-010 TERMINAL,SP 4P (MSC) a MAIN O J 0602 87-A60-881-010 JACK,PIN 2P MSP 242V05 PBSN a MAIN O J 0832 87-A60-403-010 TERMINAL,ANT PAL 2P HSP-312V05 a MAIN X JR 0808 88-108-474-080 C-RES,U 470K-1/16W J a

CX-NR11 EZSC1 MAIN O L 0201 87-A50-611-010 COIL,1UH K(CS) a MAIN O L 0202 87-A50-611-010 COIL,1UH K(CS) a MAIN O L 0451 87-007-342-010 COIL,OSC 85KHZ BIAS a MAIN O L 0801 87-A50-608-010 COIL,FM DET-N(TOK) a MAIN O L 0802 87-A91-551-010 FLTR,PCFJZH-450 L(TOK) a MAIN O L 0811 87-005-847-080 COIL,2.2UH K CECS a MAIN O L 0832 87-005-847-080 COIL,2.2UH K CECS a MAIN O L 0861 87-005-847-080 COIL,2.2UH K CECS a MAIN O L 0901 86-ZA1-612-010 COIL,FM ANT/RF-1-Z a MAIN O L 0902 86-ZA1-613-010 COIL,FM ANT/RF-2-Z a

MAIN O L 0903 87-005-847-080 COIL,2.2UH K CECS a MAIN O L 0904 86-ZA1-612-010 COIL,FM ANT/RF-1-Z a MAIN O L 0905 86-ZA1-613-010 COIL,FM ANT/RF-2-Z a MAIN O L 0906 87-005-847-080 COIL,2.2UH K CECS a MAIN O L 0907 86-ZA1-614-010 COIL,FM OSC-Z a MAIN O L 0908 88-ZA1-624-010 COIL,FM IFT 7-6.2 (COILS) a MAIN O L 0941 87-A50-020-010 COIL,ANT LW (COI) 252KHZ a MAIN O L 0942 87-A50-019-010 COIL,OSC LW (COI) 856KHZ a MAIN O L 0952 87-A50-754-010 COIL,MW ANT(3BLW) a MAIN O L 0953 87-A50-755-010 COIL,MW OSC(3BLW) a

CX-NR11 EZSC1 MAIN S Q 0001 87-A30-494-080 TR,2SA1980G a MAIN S Q 0002 87-A30-494-080 TR,2SA1980G a MAIN S Q 0003 87-A30-076-080 C-TR,2SC3052F a MAIN S Q 0009 87-A30-494-080 TR,2SA1980G a MAIN S Q 0010 87-A30-076-080 C-TR,2SC3052F a MAIN S Q 0011 87-A30-614-010 TR,2SB1548 a MAIN S Q 0012 87-A30-630-080 TR,2SC5343GL a MAIN S Q 0013 87-A30-076-080 C-TR,2SC3052F a MAIN S Q 0014 87-A30-075-080 C-TR,2SA1235F a MAIN S Q 0060 87-A30-076-080 C-TR,2SC3052F a

MAIN S Q 0061 87-A30-075-080 C-TR,2SA1235F a MAIN S Q 0062 87-A30-076-080 C-TR,2SC3052F a MAIN S Q 0063 87-A30-075-080 C-TR,2SA1235F a MAIN S Q 0064 87-A30-076-080 C-TR,2SC3052F a MAIN S Q 0101 87-A30-257-080 C-TR,2SD1306E a MAIN S Q 0102 87-A30-257-080 C-TR,2SD1306E a MAIN S Q 0103 87-A30-075-080 C-TR,2SA1235F a MAIN S Q 0104 87-A30-075-080 C-TR,2SA1235F a MAIN S Q 0105 87-A30-075-080 C-TR,2SA1235F a MAIN S Q 0106 87-A30-075-080 C-TR,2SA1235F a

– 14 –

! = ! SAFTY PARTS C = Components marked

All components used on this model at the production line are shown in this service manual. However, please note that not all components will be available as spare parts for after-sales service. Components marked S and O are designated as spare parts for service and will be stocked at the spare parts centers. Components marked X and R are not designated as spare parts for after sales service, and will not be stocked at the spare parts centers.

UNIT-NAME ! C REF-NO PARTS-NO PARTS-NAME SUFFIX&MODEL

CX-NR11 EZSC1 MAIN S Q 0107 87-A30-076-080 C-TR,2SC3052F a MAIN S Q 0108 87-A30-076-080 C-TR,2SC3052F a MAIN S Q 0109 87-A30-076-080 C-TR,2SC3052F a MAIN S Q 0110 87-A30-076-080 C-TR,2SC3052F a MAIN S Q 0111 87-A30-630-080 TR,2SC5343GL a MAIN S Q 0112 87-A30-630-080 TR,2SC5343GL a MAIN S Q 0113 87-A30-076-080 C-TR,2SC3052F a MAIN S Q 0114 87-A30-076-080 C-TR,2SC3052F a MAIN S Q 0117 87-A30-255-010 TR,2SB1342 a MAIN S Q 0118 87-A30-255-010 TR,2SB1342 a

MAIN S Q 0119 87-A30-256-010 TR,2SD1933 a MAIN S Q 0120 87-A30-256-010 TR,2SD1933 a MAIN S Q 0123 87-A30-075-080 C-TR,2SA1235F a MAIN S Q 0124 87-A30-075-080 C-TR,2SA1235F a MAIN S Q 0126 87-A30-075-080 C-TR,2SA1235F a MAIN S Q 0130 87-A30-076-080 C-TR,2SC3052F a MAIN S Q 0131 87-A30-075-080 C-TR,2SA1235F a MAIN S Q 0280 87-A30-538-040 C-TR,SRA2202S a MAIN S Q 0281 87-A30-075-080 C-TR,2SA1235F a MAIN S Q 0301 87-A30-091-080 FET,2SJ460 a

CX-NR11 EZSC1 MAIN S Q 0302 87-A30-091-080 FET,2SJ460 a MAIN S Q 0303 87-A30-090-080 FET,2SK2541 a MAIN S Q 0304 87-A30-090-080 FET,2SK2541 a MAIN S Q 0305 87-A30-091-080 FET,2SJ460 a MAIN S Q 0306 87-A30-091-080 FET,2SJ460 a MAIN S Q 0307 87-A30-090-080 FET,2SK2541 a MAIN S Q 0308 87-A30-090-080 FET,2SK2541 a MAIN S Q 0309 87-A30-090-080 FET,2SK2541 a MAIN S Q 0451 87-A30-630-080 TR,2SC5343GL a MAIN S Q 0452 87-A30-076-080 C-TR,2SC3052F a

MAIN S Q 0453 89-333-317-880 TR,2SC3331(T/U) a MAIN S Q 0454 89-333-317-880 TR,2SC3331(T/U) a MAIN S Q 0455 87-A30-119-040 C-TR,2SC3906K R a MAIN S Q 0456 87-A30-076-080 C-TR,2SC3052F a MAIN S Q 0601 87-A30-538-040 C-TR,SRA2202S a MAIN S Q 0651 87-A30-087-080 C-FET,2SK2158 a MAIN S Q 0652 87-A30-087-080 C-FET,2SK2158 a MAIN S Q 0653 87-A30-076-080 C-TR,2SC3052F a MAIN S Q 0835 87-A30-521-080 C-TR,2SC5345SF/S(O) a MAIN S Q 0836 87-A30-677-040 C-TR,SRA2207S a

CX-NR11 EZSC1 MAIN S Q 0861 87-A30-076-080 C-TR,2SC3052F a MAIN S Q 0863 87-A30-076-080 C-TR,2SC3052F a MAIN S Q 0901 89-503-602-080 C-FET,2SK360E a MAIN S Q 0902 87-A30-664-080 C-TR,2SC2620B a MAIN S Q 0903 87-A30-664-080 C-TR,2SC2620B a MAIN S Q 0904 87-A30-664-080 C-TR,2SC2620B a MAIN S Q 0905 87-A30-664-080 C-TR,2SC2620B a MAIN S Q 0948 87-A30-675-040 C-TR,2SD1306NE07TL a MAIN S Q 0951 87-A30-538-040 C-TR,SRA2202S a MAIN S Q 0952 87-A30-675-040 C-TR,2SD1306NE07TL a

MAIN S Q 0953 89-503-602-080 C-FET,2SK360E a MAIN S Q 0981 87-A30-494-080 TR,2SA1980G a MAIN S Q 0982 87-A30-076-080 C-TR,2SC3052F a MAIN S Q 0983 87-A30-076-080 C-TR,2SC3052F a MAIN X R 0001 88-100-000-010 PLATING-JW, 0.58 SN95 a MAIN X R 0005 88-100-000-010 PLATING-JW, 0.58 SN95 a MAIN X R 0009 88-108-223-080 C-RES,U 22K-1/16W J a MAIN X R 0010 88-108-223-080 C-RES,U 22K-1/16W J a MAIN X R 0011 88-108-472-080 C-RES,U 4.7K-1/16W J a MAIN X R 0012 88-118-472-080 C-RES,S 4.7K-1/10W J a

CX-NR11 EZSC1 MAIN X R 0013 88-118-472-080 C-RES,S 4.7K-1/10W J a MAIN X R 0014 88-118-100-080 C-RES,S 10-1/10W J a MAIN X R 0015 88-108-104-080 C-RES,U 100K-1/16W J a MAIN X R 0016 88-108-104-080 C-RES,U 100K-1/16W J a MAIN X R 0017 88-108-104-080 C-RES,U 100K-1/16W J a MAIN X R 0018 88-108-104-080 C-RES,U 100K-1/16W J a MAIN X R 0019 88-108-104-080 C-RES,U 100K-1/16W J a MAIN X R 0020 88-129-000-080 C-JUMPER, 3216 a MAIN X R 0024 88-118-103-080 C-RES,S 10K-1/10W J a MAIN X R 0026 88-108-472-080 C-RES,U 4.7K-1/16W J a

MAIN X R 0027 88-118-000-080 C-JUMPER,S a MAIN X R 0028 88-108-221-080 C-RES,U 220-1/16W J a MAIN X R 0029 88-108-223-080 C-RES,U 22K-1/16W J a MAIN X R 0031 88-108-154-080 C-RES,U 150K-1/16W J a MAIN X R 0032 88-108-472-080 C-RES,U 4.7K-1/16W J a MAIN X R 0035 88-118-123-080 C-RES,S 12K-1/10W J a MAIN X R 0036 88-130-182-080 RES,1.8K-1/4W J a MAIN X R 0042 88-121-331-080 RES,330-1/8W J a MAIN X R 0043 88-121-331-080 RES,330-1/8W J a MAIN X R 0044 88-121-331-080 RES,330-1/8W J a

– 15 –

! = ! SAFTY PARTS C = Components marked

All components used on this model at the production line are shown in this service manual. However, please note that not all components will be available as spare parts for after-sales service. Components marked S and O are designated as spare parts for service and will be stocked at the spare parts centers. Components marked X and R are not designated as spare parts for after sales service, and will not be stocked at the spare parts centers.

UNIT-NAME ! C REF-NO PARTS-NO PARTS-NAME SUFFIX&MODEL

CX-NR11 EZSC1 MAIN X R 0045 88-121-331-080 RES,330-1/8W J a MAIN X R 0046 88-121-821-080 RES,820-1/8W J a MAIN X R 0052 88-108-103-080 C-RES,U 10K-1/16W J a MAIN X R 0056 88-108-680-080 C-RES,U 68-1/16W J a MAIN X R 0057 88-108-472-080 C-RES,U 4.7K-1/16W J a MAIN X R 0058 88-108-103-080 C-RES,U 10K-1/16W J a MAIN X R 0059 88-108-221-080 C-RES,U 220-1/16W J a MAIN X R 0060 88-108-471-080 C-RES,U 470-1/16W J a MAIN X R 0061 88-108-103-080 C-RES,U 10K-1/16W J a MAIN X R 0065 88-108-123-080 C-RES,U 12K-1/16W J a

MAIN X R 0066 88-108-104-080 C-RES,U 100K-1/16W J a MAIN X R 0076 88-108-103-080 C-RES,U 10K-1/16W J a MAIN X R 0081 88-108-101-080 C-RES,U 100-1/16W J a MAIN X R 0091 88-130-181-080 RES,180-1/4W J a MAIN X R 0092 88-130-181-080 RES,180-1/4W J a MAIN X R 0103 88-108-332-080 C-RES,U 3.3K-1/16W J a MAIN X R 0104 88-108-332-080 C-RES,U 3.3K-1/16W J a MAIN X R 0105 88-108-273-080 C-RES,U 27K-1/16W J a MAIN X R 0106 88-108-273-080 C-RES,U 27K-1/16W J a MAIN X R 0107 88-108-101-080 C-RES,U 100-1/16W J a

CX-NR11 EZSC1 MAIN X R 0108 88-108-101-080 C-RES,U 100-1/16W J a MAIN X R 0111 88-118-102-080 C-RES,S 1K-1/10W J a MAIN X R 0112 88-118-102-080 C-RES,S 1K-1/10W J a MAIN X R 0113 88-118-273-080 C-RES,S 27K-1/10W J a MAIN X R 0114 88-118-273-080 C-RES,S 27K-1/10W J a MAIN X R 0117 88-128-103-080 C-RES, 10K-1/8W J a MAIN X R 0118 88-128-103-080 C-RES, 10K-1/8W J a MAIN X R 0119 88-118-101-080 C-RES,S 100-1/10W J a MAIN X R 0120 88-118-101-080 C-RES,S 100-1/10W J a MAIN X R 0121 88-118-101-080 C-RES,S 100-1/10W J a

MAIN X R 0122 88-118-101-080 C-RES,S 100-1/10W J a MAIN X R 0123 88-128-102-080 C-RES, 1K-1/8W J a MAIN X R 0124 88-128-102-080 C-RES, 1K-1/8W J a MAIN X R 0125 88-128-102-080 C-RES, 1K-1/8W J a MAIN X R 0126 88-128-102-080 C-RES, 1K-1/8W J a MAIN X R 0127 88-118-390-080 C-RES,S 39-1/10W J a MAIN X R 0128 88-118-390-080 C-RES,S 39-1/10W J a MAIN X R 0129 88-128-109-080 C-RES, 1-1/8W J a MAIN X R 0130 88-128-109-080 C-RES, 1-1/8W J a MAIN X R 0131 88-128-109-080 C-RES, 1-1/8W J a

CX-NR11 EZSC1 MAIN X R 0132 88-128-109-080 C-RES, 1-1/8W J a MAIN X R 0133 88-108-122-080 C-RES,U 1.2K-1/16W J a MAIN X R 0134 88-108-122-080 C-RES,U 1.2K-1/16W J a MAIN X R 0135 88-108-182-080 C-RES,U 1.8K-1/16W J a MAIN X R 0136 88-108-182-080 C-RES,U 1.8K-1/16W J a MAIN X R 0137 88-108-101-080 C-RES,U 100-1/16W J a MAIN X R 0138 88-108-101-080 C-RES,U 100-1/16W J a MAIN X R 0139 88-108-562-080 C-RES,U 5.6K-1/16W J a MAIN X R 0140 88-108-562-080 C-RES,U 5.6K-1/16W J a MAIN X R 0141 88-118-102-080 C-RES,S 1K-1/10W J a

MAIN X R 0142 88-118-102-080 C-RES,S 1K-1/10W J a MAIN X R 0143 88-128-109-080 C-RES, 1-1/8W J a MAIN X R 0144 88-128-109-080 C-RES, 1-1/8W J a MAIN X R 0145 88-128-109-080 C-RES, 1-1/8W J a MAIN X R 0146 88-128-109-080 C-RES, 1-1/8W J a MAIN X R 0157 88-108-472-080 C-RES,U 4.7K-1/16W J a MAIN X R 0158 88-108-472-080 C-RES,U 4.7K-1/16W J a MAIN X R 0159 88-108-103-080 C-RES,U 10K-1/16W J a MAIN X R 0160 88-118-103-080 C-RES,S 10K-1/10W J a MAIN X R 0165 88-118-152-080 C-RES,S 1.5K-1/10W J a

CX-NR11 EZSC1 MAIN X R 0166 88-118-152-080 C-RES,S 1.5K-1/10W J a MAIN X R 0167 88-108-103-080 C-RES,U 10K-1/16W J a MAIN X R 0168 88-118-473-080 C-RES,S 47K-1/10W J a MAIN X R 0171 88-118-222-080 C-RES,S 2.2K-1/10W J a MAIN X R 0172 88-118-222-080 C-RES,S 2.2K-1/10W J a MAIN X R 0173 88-118-182-080 C-RES,S 1.8K-1/10W J a MAIN X R 0174 88-118-182-080 C-RES,S 1.8K-1/10W J a MAIN X R 0175 88-118-331-080 C-RES,S 330-1/10W J a MAIN X R 0176 88-118-331-080 C-RES,S 330-1/10W J a MAIN X R 0178 88-118-103-080 C-RES,S 10K-1/10W J a

MAIN X R 0179 88-108-473-080 C-RES,U 47K-1/16W J a MAIN X R 0180 88-108-473-080 C-RES,U 47K-1/16W J a MAIN X R 0181 88-108-392-080 C-RES,U 3.9K-1/16W J a MAIN X R 0182 88-108-392-080 C-RES,U 3.9K-1/16W J a MAIN X R 0183 88-108-222-080 C-RES,U 2.2K-1/16W J a MAIN X R 0184 88-108-222-080 C-RES,U 2.2K-1/16W J a MAIN X R 0185 88-108-683-080 C-RES,U 68K-1/16W J a MAIN X R 0186 88-108-105-080 C-RES,U 1M-1/16W J a MAIN X R 0187 88-108-000-080 C-JUMPER,U a MAIN X R 0247 88-130-100-080 RES,10-1/4W J a

– 16 –

! = ! SAFTY PARTS C = Components marked

All components used on this model at the production line are shown in this service manual. However, please note that not all components will be available as spare parts for after-sales service. Components marked S and O are designated as spare parts for service and will be stocked at the spare parts centers. Components marked X and R are not designated as spare parts for after sales service, and will not be stocked at the spare parts centers.

UNIT-NAME ! C REF-NO PARTS-NO PARTS-NAME SUFFIX&MODEL

CX-NR11 EZSC1 MAIN X R 0248 88-130-100-080 RES,10-1/4W J a MAIN X R 0249 88-128-100-080 C-RES, 10-1/8W J a MAIN X R 0250 88-128-100-080 C-RES, 10-1/8W J a MAIN X R 0280 88-118-473-080 C-RES,S 47K-1/10W J a MAIN X R 0281 88-108-222-080 C-RES,U 2.2K-1/16W J a MAIN X R 0282 88-118-103-080 C-RES,S 10K-1/10W J a MAIN X R 0283 88-118-224-080 C-RES,S 220K-1/10W J a MAIN X R 0284 88-118-224-080 C-RES,S 220K-1/10W J a MAIN X R 0285 88-118-333-080 C-RES,S 33K-1/10W J a MAIN X R 0286 88-118-473-080 C-RES,S 47K-1/10W J a

MAIN X R 0287 88-118-473-080 C-RES,S 47K-1/10W J a MAIN X R 0301 88-108-393-080 C-RES,U 39K-1/16W J a MAIN X R 0302 88-108-393-080 C-RES,U 39K-1/16W J a MAIN X R 0303 88-108-823-080 C-RES,U 82K-1/16W J a MAIN X R 0304 88-108-823-080 C-RES,U 82K-1/16W J a MAIN X R 0305 88-108-224-080 C-RES,U 220K-1/16W J a MAIN X R 0451 88-108-222-080 C-RES,U 2.2K-1/16W J a MAIN X R 0453 88-108-472-080 C-RES,U 4.7K-1/16W J a MAIN X R 0454 88-121-829-080 RES,8.2-1/8W J a MAIN X R 0455 88-108-183-080 C-RES,U 18K-1/16W J a

CX-NR11 EZSC1 MAIN X R 0456 88-108-183-080 C-RES,U 18K-1/16W J a MAIN X R 0457 88-108-104-080 C-RES,U 100K-1/16W J a MAIN X R 0458 88-108-563-080 C-RES,U 56K-1/16W J a MAIN X R 0459 88-108-472-080 C-RES,U 4.7K-1/16W J a MAIN X R 0461 88-108-472-080 C-RES,U 4.7K-1/16W J a MAIN X R 0462 88-108-471-080 C-RES,U 470-1/16W J a MAIN X R 0467 88-108-472-080 C-RES,U 4.7K-1/16W J a MAIN X R 0468 88-108-272-080 C-RES,U 2.7K-1/16W J a MAIN X R 0469 88-108-150-080 C-RES,U 15-1/16W J a MAIN X R 0601 88-108-820-080 C-RES,U 82-1/16W J a

MAIN X R 0602 88-108-820-080 C-RES,U 82-1/16W J a MAIN X R 0603 88-108-394-080 C-RES,U 390K-1/16W J a MAIN X R 0604 88-108-394-080 C-RES,U 390K-1/16W J a MAIN X R 0605 88-108-122-080 C-RES,U 1.2K-1/16W J a MAIN X R 0606 88-108-122-080 C-RES,U 1.2K-1/16W J a MAIN X R 0607 88-108-183-080 C-RES,U 18K-1/16W J a MAIN X R 0608 88-108-183-080 C-RES,U 18K-1/16W J a MAIN X R 0609 88-108-472-080 C-RES,U 4.7K-1/16W J a MAIN X R 0610 88-108-472-080 C-RES,U 4.7K-1/16W J a MAIN X R 0611 88-108-223-080 C-RES,U 22K-1/16W J a

CX-NR11 EZSC1 MAIN X R 0612 88-108-223-080 C-RES,U 22K-1/16W J a MAIN X R 0613 88-108-273-080 C-RES,U 27K-1/16W J a MAIN X R 0614 88-108-273-080 C-RES,U 27K-1/16W J a MAIN X R 0615 88-108-153-080 C-RES,U 15K-1/16W J a MAIN X R 0616 88-108-153-080 C-RES,U 15K-1/16W J a MAIN X R 0617 88-108-153-080 C-RES,U 15K-1/16W J a MAIN X R 0619 88-108-153-080 C-RES,U 15K-1/16W J a MAIN X R 0621 88-108-332-080 C-RES,U 3.3K-1/16W J a MAIN X R 0622 88-108-332-080 C-RES,U 3.3K-1/16W J a MAIN X R 0623 88-108-222-080 C-RES,U 2.2K-1/16W J a

MAIN X R 0624 88-108-222-080 C-RES,U 2.2K-1/16W J a MAIN X R 0625 88-108-103-080 C-RES,U 10K-1/16W J a MAIN X R 0626 88-108-103-080 C-RES,U 10K-1/16W J a MAIN X R 0627 88-108-222-080 C-RES,U 2.2K-1/16W J a MAIN X R 0628 88-108-222-080 C-RES,U 2.2K-1/16W J a MAIN X R 0629 88-108-103-080 C-RES,U 10K-1/16W J a MAIN X R 0630 88-108-103-080 C-RES,U 10K-1/16W J a MAIN X R 0631 88-108-222-080 C-RES,U 2.2K-1/16W J a MAIN X R 0632 88-108-222-080 C-RES,U 2.2K-1/16W J a MAIN X R 0633 88-108-222-080 C-RES,U 2.2K-1/16W J a

CX-NR11 EZSC1 MAIN X R 0634 88-108-222-080 C-RES,U 2.2K-1/16W J a MAIN X R 0635 88-108-102-080 C-RES,U 1K-1/16W J a MAIN X R 0636 88-108-102-080 C-RES,U 1K-1/16W J a MAIN X R 0637 88-108-102-080 C-RES,U 1K-1/16W J a MAIN X R 0638 88-108-102-080 C-RES,U 1K-1/16W J a MAIN X R 0639 88-108-183-080 C-RES,U 18K-1/16W J a MAIN X R 0640 88-108-183-080 C-RES,U 18K-1/16W J a MAIN X R 0641 88-121-223-080 RES,22K-1/8W J a MAIN X R 0642 88-108-222-080 C-RES,U 2.2K-1/16W J a MAIN X R 0643 88-108-104-080 C-RES,U 100K-1/16W J a

MAIN X R 0644 88-108-104-080 C-RES,U 100K-1/16W J a MAIN X R 0649 88-108-332-080 C-RES,U 3.3K-1/16W J a MAIN X R 0650 88-108-332-080 C-RES,U 3.3K-1/16W J a MAIN X R 0651 88-108-101-080 C-RES,U 100-1/16W J a MAIN X R 0652 88-108-101-080 C-RES,U 100-1/16W J a MAIN X R 0656 88-121-394-080 RES,390K-1/8W J a MAIN X R 0657 88-108-274-080 C-RES,U 270K-1/16W J a MAIN X R 0658 88-108-274-080 C-RES,U 270K-1/16W J a MAIN X R 0659 88-108-394-080 C-RES,U 390K-1/16W J a MAIN X R 0660 88-108-274-080 C-RES,U 270K-1/16W J a

– 17 –

! = ! SAFTY PARTS C = Components marked

All components used on this model at the production line are shown in this service manual. However, please note that not all components will be available as spare parts for after-sales service. Components marked S and O are designated as spare parts for service and will be stocked at the spare parts centers. Components marked X and R are not designated as spare parts for after sales service, and will not be stocked at the spare parts centers.

UNIT-NAME ! C REF-NO PARTS-NO PARTS-NAME SUFFIX&MODEL

CX-NR11 EZSC1 MAIN X R 0661 88-108-392-080 C-RES,U 3.9K-1/16W J a MAIN X R 0662 88-108-392-080 C-RES,U 3.9K-1/16W J a MAIN X R 0672 88-108-223-080 C-RES,U 22K-1/16W J a MAIN X R 0673 88-108-392-080 C-RES,U 3.9K-1/16W J a MAIN X R 0674 88-108-273-080 C-RES,U 27K-1/16W J a MAIN X R 0677 88-108-223-080 C-RES,U 22K-1/16W J a MAIN X R 0678 88-108-223-080 C-RES,U 22K-1/16W J a MAIN X R 0789 88-108-473-080 C-RES,U 47K-1/16W J a MAIN O R 0790 87-012-286-080 C-CAP,U 0.01-25 K B a MAIN X R 0791 88-108-102-080 C-RES,U 1K-1/16W J a

MAIN X R 0793 88-108-221-080 C-RES,U 220-1/16W J a MAIN X R 0795 88-108-000-080 C-JUMPER,U a MAIN X R 0801 88-108-103-080 C-RES,U 10K-1/16W J a MAIN X R 0802 88-108-223-080 C-RES,U 22K-1/16W J a MAIN X R 0803 88-128-183-080 C-RES, 18K-1/8W J a MAIN X R 0804 88-108-000-080 C-JUMPER,U a MAIN X R 0805 88-108-332-080 C-RES,U 3.3K-1/16W J a MAIN X R 0806 88-108-682-080 C-RES,U 6.8K-1/16W J a MAIN X R 0809 88-108-102-080 C-RES,U 1K-1/16W J a MAIN X R 0810 88-108-102-080 C-RES,U 1K-1/16W J a

CX-NR11 EZSC1 MAIN X R 0811 88-108-000-080 C-JUMPER,U a MAIN X R 0812 88-108-000-080 C-JUMPER,U a MAIN X R 0813 88-108-224-080 C-RES,U 220K-1/16W J a MAIN X R 0814 88-108-222-080 C-RES,U 2.2K-1/16W J a MAIN X R 0815 88-121-682-080 RES,6.8K-1/8W J a MAIN X R 0818 88-108-103-080 C-RES,U 10K-1/16W J a MAIN X R 0821 88-108-000-080 C-JUMPER,U a MAIN X R 0823 88-108-473-080 C-RES,U 47K-1/16W J a MAIN X R 0826 88-108-223-080 C-RES,U 22K-1/16W J a MAIN X R 0832 88-108-391-080 C-RES,U 390-1/16W J a

MAIN X R 0840 88-108-221-080 C-RES,U 220-1/16W J a MAIN X R 0850 88-108-103-080 C-RES,U 10K-1/16W J a MAIN X R 0851 88-118-470-080 C-RES,S 47-1/10W J a MAIN X R 0853 88-108-102-080 C-RES,U 1K-1/16W J a MAIN X R 0854 88-108-331-080 C-RES,U 330-1/16W J a MAIN X R 0855 88-108-183-080 C-RES,U 18K-1/16W J a MAIN X R 0856 88-108-103-080 C-RES,U 10K-1/16W J a MAIN X R 0857 88-108-181-080 C-RES,U 180-1/16W J a MAIN X R 0858 88-108-271-080 C-RES,U 270-1/16W J a MAIN X R 0860 88-108-101-080 C-RES,U 100-1/16W J a

CX-NR11 EZSC1 MAIN X R 0861 88-108-471-080 C-RES,U 470-1/16W J a MAIN X R 0862 88-108-272-080 C-RES,U 2.7K-1/16W J a MAIN X R 0863 88-108-104-080 C-RES,U 100K-1/16W J a MAIN X R 0864 88-108-123-080 C-RES,U 12K-1/16W J a MAIN X R 0865 88-108-471-080 C-RES,U 470-1/16W J a MAIN X R 0867 88-108-104-080 C-RES,U 100K-1/16W J a MAIN X R 0870 88-121-102-080 RES,1K-1/8W J a MAIN X R 0871 88-121-102-080 RES,1K-1/8W J a MAIN X R 0901 88-108-104-080 C-RES,U 100K-1/16W J a MAIN X R 0902 88-108-104-080 C-RES,U 100K-1/16W J a

MAIN X R 0903 88-108-330-080 C-RES,U 33-1/16W J a MAIN X R 0904 88-108-103-080 C-RES,U 10K-1/16W J a MAIN X R 0905 88-108-102-080 C-RES,U 1K-1/16W J a MAIN X R 0906 88-108-564-080 C-RES,U 560K-1/16W J a MAIN X R 0908 88-108-271-080 C-RES,U 270-1/16W J a MAIN X R 0909 88-108-181-080 C-RES,U 180-1/16W J a MAIN X R 0910 88-108-334-080 C-RES,U 330K-1/16W J a MAIN X R 0911 88-108-181-080 C-RES,U 180-1/16W J a MAIN X R 0912 88-108-104-080 C-RES,U 100K-1/16W J a MAIN X R 0913 88-108-152-080 C-RES,U 1.5K-1/16W J a

CX-NR11 EZSC1 MAIN X R 0914 88-108-472-080 C-RES,U 4.7K-1/16W J a MAIN X R 0915 88-108-104-080 C-RES,U 100K-1/16W J a MAIN X R 0916 88-108-470-080 C-RES,U 47-1/16W J a MAIN X R 0926 88-108-101-080 C-RES,U 100-1/16W J a MAIN X R 0944 88-108-101-080 C-RES,U 100-1/16W J a MAIN X R 0945 88-108-104-080 C-RES,U 100K-1/16W J a MAIN X R 0947 88-108-183-080 C-RES,U 18K-1/16W J a MAIN X R 0948 88-108-472-080 C-RES,U 4.7K-1/16W J a MAIN X R 0952 88-108-562-080 C-RES,U 5.6K-1/16W J a MAIN X R 0954 88-108-222-080 C-RES,U 2.2K-1/16W J a

MAIN X R 0956 88-108-471-080 C-RES,U 470-1/16W J a MAIN X R 0958 88-108-472-080 C-RES,U 4.7K-1/16W J a MAIN X R 0959 88-108-103-080 C-RES,U 10K-1/16W J a MAIN X R 0962 88-121-102-080 RES,1K-1/8W J a MAIN X R 0964 88-108-330-080 C-RES,U 33-1/16W J a MAIN X R 0968 88-108-822-080 C-RES,U 8.2K-1/16W J a MAIN X R 0969 88-108-102-080 C-RES,U 1K-1/16W J a MAIN X R 0973 88-108-102-080 C-RES,U 1K-1/16W J a MAIN X R 0975 88-108-562-080 C-RES,U 5.6K-1/16W J a MAIN X R 0976 88-108-102-080 C-RES,U 1K-1/16W J a

– 18 –

! = ! SAFTY PARTS C = Components marked

All components used on this model at the production line are shown in this service manual. However, please note that not all components will be available as spare parts for after-sales service. Components marked S and O are designated as spare parts for service and will be stocked at the spare parts centers. Components marked X and R are not designated as spare parts for after sales service, and will not be stocked at the spare parts centers.

UNIT-NAME ! C REF-NO PARTS-NO PARTS-NAME SUFFIX&MODEL

CX-NR11 EZSC1 MAIN X R 0977 88-108-102-080 C-RES,U 1K-1/16W J a MAIN X R 0978 88-108-681-080 C-RES,U 680-1/16W J a MAIN X R 0979 88-108-123-080 C-RES,U 12K-1/16W J a MAIN X R 0980 88-108-684-080 C-RES,U 680K-1/16W J a MAIN X R 0981 88-121-471-080 RES,470-1/8W J a MAIN X R 0982 88-108-682-080 C-RES,U 6.8K-1/16W J a MAIN X R 0983 88-108-392-080 C-RES,U 3.9K-1/16W J a MAIN X R 0984 88-108-562-080 C-RES,U 5.6K-1/16W J a MAIN X R 0985 88-121-471-080 RES,470-1/8W J a MAIN X R 0986 88-121-221-080 RES,220-1/8W J a

MAIN X R 0987 88-121-472-080 RES,4.7K-1/8W J a MAIN X R 0988 88-108-103-080 C-RES,U 10K-1/16W J a MAIN X R 0989 88-121-102-080 RES,1K-1/8W J a MAIN X R 0990 88-108-563-080 C-RES,U 56K-1/16W J a MAIN O R 0991 87-012-195-080 C-CAP,U 100P-50 J CH a MAIN X R 0992 88-108-103-080 C-RES,U 10K-1/16W J a MAIN O R 0993 87-012-195-080 C-CAP,U 100P-50 J CH a MAIN X R 0994 88-108-103-080 C-RES,U 10K-1/16W J a MAIN O R 0995 87-012-195-080 C-CAP,U 100P-50 J CH a MAIN X R 0996 88-108-103-080 C-RES,U 10K-1/16W J a

CX-NR11 EZSC1 MAIN X R 0997 88-108-154-080 C-RES,U 150K-1/16W J a MAIN X R 0998 88-108-102-080 C-RES,U 1K-1/16W J a MAIN X R 0999 88-108-103-080 C-RES,U 10K-1/16W J a MAIN O RY 0001 87-A91-339-010 RELAY,AC DC12V G5PA-2 a MAIN O SFR0451 87-024-435-080 SFR,33K H RH063MC a MAIN O SFR0452 87-024-435-080 SFR,33K H RH063MC a MAIN X SH 0301 8C-NF5-221-010 PLATE,SHLD DECK M a MAIN X SH 0901 8C-NF9-619-010 SHLD-CASE,CNF-9 EZ P a MAIN O TC 0942 87-A91-774-080 TRIMMER,PLY 30P 6.8X5.4 CDYL a MAIN O TH 0101 87-A91-042-080 C-THMS,100K 55001 a

MAIN O TH 0102 87-A91-042-080 C-THMS,100K 55001 a MAIN O W 0101 8B-NF1-640-010 F-CABLE,5P 2.5 250MM a MAIN O WH 0001 87-A90-459-010 HLDR,WIRE 2.5-5P a MAIN O WH 0101 87-A90-459-010 HLDR,WIRE 2.5-5P a MAIN O X 0862 87-A70-307-010 VIB,XTAL 4.332MHZ CSA-309ST a MAIN O X 0992 87-A70-306-010 VIB,XTAL 4.500MHZ CSA-309ST a PT O C 0091 87-A12-317-080 C-CAP,U 0.1-50 Z F a PT ! O PT 0001 8C-NFA-601-010 PT,CNF-A EZ a PT ! O T 0001 87-A60-317-010 TERMINAL, 1P MSC a PT ! O T 0002 87-A60-317-010 TERMINAL, 1P MSC a

CX-NR11 EZSC1 PT O W 0099 8C-NFA-605-010 F-CABLE,5P 2.5 480MM a PT O WH 0002 87-A90-459-010 HLDR,WIRE 2.5-5P a

– 19 –

CHIP RESISTOR PART CODE

Chip Resistor Part Coding

88

A

Resistor Code

Chip resistor

Wattage Type Tolerance 1/16W 1005 5% CJ

1/16W 1/10W

1/8W

1608 2125

3216

5% 5%

5%

Symbol

CJ CJ

CJ

Figure

Value of resistor

Form

L

Dimensions (mm)

t

W

0.55

Resistor Code

108 118

128

LW t

1.0 0.5 0.35 104

1.6 0.8 0.45 2 1.25 0.45

3.2

1.6

: A : A

– 20 –

TRANSISTOR ILLUSTRATION

B C E

2SB1548

E C B

2SA1585SR

B C E

2SB1342 2SD1933

S D G

2SJ460 2SK2541

E C B

2SA1980G 2SA1981Y 2SC3331(T/U)

S

D

G

2SK360E

E C B

2SC5343GL

G

S

2SK2158

D

B

2SA1235F 2SC2620B 2SC3052F 2SC3906K R 2SC5345SF/S(O)

C

E

2SD1306E 2SD1306NE07TL SRA2202S SRA2207S

– 21 –

SCHEMATIC DIAGRAM – 1 (MAIN 1 / 2)

– 23 –

SCHEMATIC DIAGRAM – 2 (MAIN 2 / 2)

– 24 –

SCHEMATIC DIAGRAM – 3 (HP)

– 25 –

SCHEMATIC DIAGRAM – 4 (FRONT / DECK)

– 27 –

WIRING – 3 (PT)

15 14 13 12 11 10 9 8 7 6 5 4 3 2 1

A

B

C

D

E

F

G

H

I

J

K

L

M

N

O

P

Q

– 28 –

R

S

T

U

SCHEMATIC DIAGRAM – 5 (PT)

– 29 –

WIRING – 4 (DECK)

32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1

A

B

SW5

J1 J2

R

SW4

DECK 1 P HEAD

SW3

R+

L+

R1

VR

DECK 2

E / RP HEAD

E

R2

R+ R

C1

SW2

C

D

SW1

E

F

G

H

I

J

K

L

M

L

WHT

BLK

GRY

WHT

BLK

2

1

3

CNA301

TO MAIN C.B

CN301

RED

1

E+

BLK

WHT

GRY

WHT

2

GRN

BLK

4

CNA302

L+

YEL

BRN

YEL

5

L

3

TO MAIN C.B

CN302

6

RED

GRY

RED

7

WHT

8

N

O

P

Q

BLK

R

S

T

U

– 30 –

IC BLOCK DIAGRAM

– 31 –

FL (HUA – 13SS09T) GRID ASSIGNMENT / PIN CONNECTION / ANODE CONNECTION

GRID ASSIGNMENT ANODE CONNECTION

PIN CONNECTION

– 32 –

IC DESCRIPTION

IC, µPD780228GF-089-3BA

Pin No.

1 O-MOTOR O DECK motor output. 2 O-SOL1 O DECK1 solenoid output. 3 O-SOL2 O DECK2 solenoid output. 4 O-STBY LED O Standby LED output. (Not used) 5 O-MUTE O System mute ON/OFF output. 6 O-KSCAN O Key scan timing output. 7 O-PLL_CE O PLL chip enable output for LC72131D-N. 8 I-TM_BASE I Time-base signal input.

9 O-TU-ON O Tuner ON/OFF output. 10 O-PB2 O DECK2 play back ON/OFF output. 11 O-VF – Not used. 12 I-AUTO1 I DECK1 detecting reel rotation switch input. 13 I-REA I DECK2 prevention for mistaken recording switch input. 14 I-CST1 I DECK1 cassette detect switch input. 15 I-CST2 I DECK2 cassette detect switch input. 16 I-AUTO2 I DECK2 detecting reel rotation switch input. 17 IC – GND. 18 VSS0 – GND. 19 VDD0 – Power supply input. 20 O-POWER O System power supply ON/OFF output. 21 I-JOG_A I JOG rotary encoder signal input (A/D). 22 I-JOG_B I JOG rotary encoder signal input (A/D). 23 I-VOL_A I VOL rotary encoder signal input (A/D). 24 I-VOL_B I VOL rotary encoder signal input (A/D). 25 I-SUBQ I CD SUBQ serial input. 26 I-WRQ I CD IC control input. 27 I-DRF I CD IC control input. 28 I-RDS_CLK I Tuner RDS clock output for BU1920FS. 29 I-RDS_DATA I Tuner RDS data output for BU1920FS. 30 RESET I Reset input. 31 O-DSC/O-DATA O Serial data latch output for BD3881FV / PLL data output for LC72131D-N. 32 O-CLK_SFT O MICON clock shift output. 33 I-IFC I Tune IF count serial data input. 34 I-RMC I System remote control signal input. 35 I-DISH I CD turntable photo sensor signal input. 36 I-STEREO I Tuner stereo detected input. 37 VDD1 – Power supply input. 38 X2 – 4.19MHz oscillator circuit. 39 X1 – 4.19MHz oscillator circuit. 40 VSS – GND. 41 AVDD – GND. 42 I-HOLD I Power failure detected input "L" to stop clock and hold memory. 43 I-CDSW I CD mechanical switch A/D converter input.

Pin Name I/O

Description

– 33 –

Pin No.

44 I-SPEANA_1 I A/D input for spectrum analyser level display. 45 I-SPEANA_2 I A/D input for spectrum analyser level display. 46 I-SPEANA_3 I A/D input for spectrum analyser level display. 47 I-KEY 1 I Key A/D input 1. 48 I-KEY 2 I Key A/D input 2. 49 I-TU_SIG I Tuner RDS signal input. (Connected to GND through a resistor) 50 AVSS – GND. 51 O-BIAS O Bias output. 52 O-CD_CE O CD chip enable output. 53 O-CD_CLK O CD serial clock output. 54 O-CD_DATA O CD serial data output. 55 O-CLK O PLL clock output for LC72131D-N.

56 ~ 59 NC – Not connected.

60 I-CAM2 I DECK2 cam switch input. 61 I-CAM1 I DECK1 cam switch input.

62 ~ 70 P24 ~ P16 O FL segment P24 ~ P16 output.

71 P15/AM 10K O/I FL segment P15 output / AM 10K data input to diode (not used). 72 P14/KARAOKE O/I FL segment P14 output / KARAOKE data input to diode (not used). 73 P13/LW O/I FL segment P13 output / LW data input to diode. 74 P12/SW O/I FL segment P12 output / SW data input to diode (not used). 75 P11/OIRT O/I FL segment P11 output / OIRT data input to diode (not used). 76 P10/FM WIDE O/I FL segment P10 output / FM WIDE data input to diode (not used). 77 P9/R+1 O/I FL segment P9 output / R+1 data input to diode (not used). 78 P8/DEMO O/I FL segment P8 output / DEMO data input to diode (not used). 79 VDD2 – Power supply input. 80 VLOAD _ Power supply for FL display. 81 P7 O FL segment P7 output. 82 P6/WITHOUT-ECO O/I FL segment P6 output / WITHOUT-ECO data input to diode .

83 ~ 87 P5 ~ P1 O FL segment P5 ~ P1 output.

88 ~ 100 G1 ~ G13 O FL grid G1 ~ G13 output.

Pin Name I/O Description

– 34 –

ADJUSTMENT (TUNER / DECK / FORNT)

MAIN C.B

18

Z

PARTS SIDE

SFR451

SFR452

5

L802

1

L942

L907

TC942 L941

L953

L952

L905 L904

L901

L902

J203

7

6

9

3

5 6 7 9

MAIN C.B PATTERN SIDE

IC801

4

GND

1

VT

2 3

24

TP8

L

TP9

G

R

15 16 17 18 19

DECK C.B

MOTOR

12

SFR

15

PH

RPH

15

– 35 –

1. VT Adjustment and Check (LW) Requirements * Measuring instrument: Digital multimeter

Test point: VT, GND

Adjustment point: L942 (1) Connect a digital multimeter to VT and GND. (2) Set the unit function to LW, and adjust the receiving frequency at 144 kHz. (3) Adjust L942 so that the digital multimeter indicates 1.3 ± 0.05 V.

2. VT Check (MW) Requirements: Same as Item 1 (1) Connect the digital multimeter to VT and GND. (2) Set the unit function to MW, and adjust the receiving frequency to 1,602 kHz. (3) Check that the digital multimeter indicates 8.0 V or below. (4) Adjust the receiving frequency of the unit to 531 kHz. (5) Check that the digital multimeter indicates 0.5 V or above.

3. VT Adjustment and Check (FM) Requirements: Same as Item 1. (1) Connect the digital multimeter to VT and GND. (2) Set the unit function to FM, and adjust the receiving frequency at 108.0 MHz. (3) Adjust L907 so that the digital multimeter indicates 7.0 ± 0.1 V. (4) Adjust the receiving frequency of the unit to 87.5 MHz. (5) Check that the digital multimeter indicates 0.5 V or above.

DIGITAL MULTIMETER

V

VT

GND

4. Clock Check Requirements * Measuring instrument: Frequency counter

Test point: CLOCK, GND (1) Connect the frequency counter to CLOCK and GND. (2) Set the unit function to MW, and adjust the receiving frequency to 1,602 kHz. (3) Check that the frequency counter indicates 2,160 kHz ± 45 Hz.

FREQ U E NC Y COU NTE R

Hz

CLOCK

GND

– 36 –

<MW/LW Adjustment> Make sure that the following settings are done before adjustment.

Preparation * Measuring instruments:

Standard Signal Generator (S.S.G.) / Loop antenna / Oscilloscope / Millivoltmeter / Dummy resistor (6Ω) (1) Connect the measuring instruments as shown in the diagram below. (2) Keep a distance of 60cm between the loop antenna of signal generator and the one connected to the unit.

60cm

Standard Signal Generator

Standerd Signal Genertaor

SET

SPOUT(L) SPOUT(R)

AC MILLIVOLTMETER

DUMMY

LOAD

Ω

6

CH2CH1

OSCILLOSCOPE

OUTPUT

CH2CH1

5. IF Adjustment (MW) Requirements * Test point: SP OUT (Lch, Rch)

Adjustment point: L802 (1) Adjust the S.S.G. setting to MW; carrier at 999 kHz with 30% modulation, and source at 1 kHz, position output at maximum. (2) Adjust the unit to MW 999 kHz. (3) While monitoring the 1 kHz waveform through oscilloscope, decrease the S.S.G. output level (till slight noises appear in the waveform). (4) Adjust L802 so that the millivoltmeter indicates maximum.

6. Tracking Adjustment (MW) Requirements: Same as Item 5. * Adjustment point: L952 / L953 (1) Adjust the S.S.G. setting to AM; carrier at 999 kHz with 30% modulation, and source at 1 kHz, position output at maximum. (2) Adjust the unit to MW 999 kHz. (3) While monitoring the 1 kHz waveform through oscilloscope, decrease the S.S.G. output level (till slight noises appear in the waveform.) (4) Adjust L952 so that the millivoltmeter indicates maximum. (5) Adjust the S.S.G setting to AM; carrier at 603 kHz; distortion rate at 30 %, and source at 1 kHz. (6) Adjust the unit to MW 603 kHz. (7) Adjust L953 so that the millivoltmeter indicates maximum. (8) Repeat above steps (1) to (7) two to three times.

7. Tracking Adjustment (LW) Requirements: Same as Item 5. * Adjustment point: TC942 / L941 (1) Adjust TC942 to the mechanical center. (2) Adjust the S.S.G. setting to AM; carrier at 144 kHz with 30% modulation, and source at 1 kHz, position output at maximum. (3) Adjust the unit to LW 144 kHz. (4) While monitoring 1 kHz waveform through oscilloscope, decrease the S.S.G. output level (till slight noises appear in the waveform). (5) Adjust L941 so that the millivoltmeter indicates the maximum level. (6) Adjust the S.S.G setting to AM; carrier at 290 kHz; distortion rate at 30 %, and source at 1 kHz. (7) Adjust the unit to LW 290 kHz. (8) Adjust TC942 so that the millivoltmeter indicates the maximum level. (9) Repeat the above steps (2) to (8) two to three times.

– 37 –

8. Auto-Stop Function Check (MW) Requirements: Same as Item 5. (1) Adjust the S.S.G setting to AM; carrier at 999 kHz; distortion rate at 30 %; source at 1 kHz, and output at 40 ~ 70 dBuV. (2) Start the tuning search mode, and check that the auto-stop function is applied at MW 999 kHz.

<FM Adjustment> Make sure that the following settings are done before adjustment.

Preparation * Measuring instruments: Standard Signal Generator (S.S.G.) / Oscilloscope / Millivoltmeter / Dummy resistor (6Ω) (1) Connect the measuring instruments as shown in the diagram below. (2) Connect the output terminal of signal generator to the antenna input terminal of the unit.

Standard Signal Generator

Standerd Signal G enertaor

SET

FM ANT

SPOUT(L) SPOUT(R)

AC MILLIVOLTMETER

DUMMY

LOAD

Ω

6

CH2CH1

OSCILLOSCOPE

OUTPUT

CH2CH1

9. Tracking Adjustment Requirements * Test Point: SP OUT (Lch, Rch) Adjustment point: L901, L902, L904, L905 (1) Adjust the S.S.G. setting to FM; carrier at 108 MHz, distortion at 75 kHz , and source 1 kHz, position output at maximum. (2) Adjust the unit to FM 108 MHz. (3) While monitoring 1 kHz waveform through oscilloscope, decrease the S.S.G. output level (till slight noises appear in the waveform). (4) Adjust L905–>L904–>L902–>L901–>L902–>L904–>L905. Repeat adjustment (L905, L904, L902, L901) two to three time so that the

millivoltmeter indicates the maximum level.

10. Separation Check Requirements: Same as Item 9. (1) Adjust the S.S.G. setting to FM; carrier at 98 MHz; distortion at 67.5 kHz; source at 1 kHz, and output at 60 dBuV. (2) Switch the S.S.G. to PILOT ON, and set to PILOT 7.5 kHz. (3) Adjust the unit to FM 98 MHz. (4) Check that S.S.G outputs only from Lch and that the difference between Lch and Rch at that time is 12 dB or above. (5) Check for Rch in the same manner.

11. Auto-Stop Function Check Requirements: Same as Item 5. (1) Adjust the S.S.G. setting to FM; carrier at 108 MHz; distortion at 75 kHz; source at 1 kHz and output at 10 ~ 35 dBuV. (2) Start the tuning search mode, and check that the auto-stop function is applied at FM 108 MHz.

– 38 –

12. Tape Speed Adjustment (DECK 2) Requirements * Measuring instruments: Wow-flutter meter (frequency counter)

T est tape: TTA-100 (3 kHz) Test point: HP OUT Adjustment point: DECK MOTOR SFR

(1) Connect the HP OUT terminal of the unit to the wow-flutter meter. (2) Insert the test tape (TTA-100) to DECK 2. Playback the middle part of the tape in the FWD

direction, and adjust DECK MOTOR SFR so that the level, 3,000 Hz ± 45 Hz can be obtained.

13. Tape Speed Check (DECK 1) Requirements: Same as Item 12 (1) Insert the test tape (TTA-100) to DECK 1. Playback the middle part of the tape, and

check that the range within ± 55 Hz is obtained against the speed of DECK 2.

14. Wow-Flutter Check (DECK 1, DECK 2) Requirements: Same as Item 12. (1) Connect the HP OUT terminal of the unit to the wow-flutter meter. (2) Switch the wow-flutter setting from INDICATOR to JIS, and from a mode to W RMS (WTD). (3) Playback the middle part of the test tape (TTA-100), and check that the level is 0.25 % or below.

HP OUT

WOW&FLUTTER METER

Hz

INPUT

%

15. Head Azimuth Adjustment (DECK 1, DECK 2) Requirements * Measuring instrument: Oscilloscope

T est tape: TTA-300 (10 kHz)

Test point: TP8 (Lch), TP9 (Rch) Adjustment point: Head azimuth adjustment screw (1) Connect the CH1 of the oscilloscope probe to TP8 (Lch) and the CH2 to TP9 (Rch). (2) Set the V mode of the oscilloscope to ADD. (3) Insert the test tape (TTA-300) to DECK 1. Playback the middle part of the tape in the

FWD direction, and adjust the head azimuth adjustment screw so that the waveform

reaches maximum when 10 kHz is played. (4) After adjustment, lock the screw by bonding (1600B). (5) Apply the above steps (3) to (4) to DECK 2.

16. Playback Frequency Check (DECK 1, DECK 2) Requirements * Measuring instrument: Millivoltmeter

Test tape: TTA-300 (315 Hz / 10 kHz)

Test point: TP8 (Lch), TP9 (Rch) (1) Connect the CH1 of millivoltmeter to TP8 (Lch) and the CH2 to TP9 (Rch). (2) Insert the test tape (TTA-300) to DECK 1, and playback 315 Hz and 10 kHz. (3) Check that the 10 kHz level is ranged within ± 3 dB compared to the output reference

level of 315 Hz. (4) Apply the above steps (2) and (3) to DECK 2.

OSCILLOSCOPE

OUTPUT

CH1 CH2

TP8

TP9

AC MILLIVOLTME TER

CH2CH1

TP8 TP9

– 39 –

17. Playback Sensitivity Check (DECK 1, DECK 2) Requirements * Measuring instrument: Millivoltmeter

Test tape: TTA-200 (400 Hz)

Test point: TP8 (Lch), TP9 (Rch) (1) Connect the CH1 of millivoltmeter to TP8 (Lch) and the CH2 to TP9 (Rch). (2) Insert the test tape (TTA-200) to DECK 1 to playback. (3) Check that the output level is ranged within 110 mV ± 3 dB. (4) Apply the above steps (2) and (3) to DECK 2.

18. Playback/Record Frequency Response Adjustment (DECK 2) Requirements * Measuring instruments: Millivoltmeter

Audio signal oscillator (low-frequency oscillator) Attenuator

AUDIO SIGNAL

GENERATOR

ATTENUATOR

SET

Test tape: TTA-602 (NORMAL) Test point: TP8 (Lch), TP9 (Rch) Input point: AUX (1 kHz / 8 kHz)

OUTPUT

(1kHz, 1V)

INPUT

OUTPUT

AUX(L) AUX(R)

TP8

TP9

Adjustment point: SFR451 (Lch), SFR452 (Rch) (1) Connect the CH1 of millivoltmeter to TP8 (Lch) and the CH2 to TP9 (Rch). (2) Connect the output terminal of oscillator to attenuator, and then attenuator to AUX of the unit. (3) Insert the test tape (TTA-602) to DECK 2, and record the 1 kHz signal from AUX. (4) Adjust the attenuator so that the output levels of TP8 and TP9 become 10 mV. (5) Record 1 kHz and 8 kHz alternately. (6) Adjust SFR451 (Lch) and SFR452 (Rch) so that the playback output level of 8 kHz is ranged within 0 ± 1 dB compared to the

playback output reference level of 1 kHz.

AC MILLIVOLTMETER

CH2CH1

19. Playback/Record Sensitivity Check (DECK 2) Requirements * Measuring instrument: Same as Item 18.

T est tape: TTA-602 (NORMAL) Test point: TP8 (Lch), TP9 (Rch)

Input point: AUX (1 kHz) (1) Insert the test tape (TTA-602) to DECK 2, and record the 1 kHz signal from AUX. (2) Adjust the attenuator so that the output levels of TP8 and TP9 become 100 mV. (3) Playback 1 kHz, and check that the output level is ranged within 0 dB ± 2.5 dB compared to the output level during recording.

– 40 –

FRONT C.B PATTERN SIDE

20

FRONT C.B PARTS SIDE

20

KSCAN

GND

L951

20. Clock Adjustment Requirement * Measuring instrument: Frequency counter

Test point: CLOCK, GND

Adjustment point: L951 (1) While pressing and holding down the POWER button and the UP button, insert the AC plug. (2) Adjust L951 so that the frequency counter indicates 72.743 ± 0.073 Hz.

– 41 –

FREQUENCY COUNTER

Hz

CLOCK

GND

CD TEST MODE

• RF frequency check (approx. 1.7Vp-p)

CD TEST MODE Ver. 3.0

1. Starting CD Test Mode

While pressing and holding down the CD OPEN/CLOSE button, insert the AC plug to outlet. When test mode starts, the message, “ TEST” appears on the display.

2. Exiting CD Test Mode

Press the other function button, POWER button or remove the AC plug from outlet.

3. Function of CD Test Mode

No Mode Function Key Display Movement Check

1 Start Mode All lit. FL all lit. • FL check

• Microcomputer check

2 Search Mode STOP button READING • LD constantly lit. • APC circuit check

• Focus search continuous • Laser current electricity measurement movement *1, 2 • Focus search waveform check

• Spindle motor continuous kick • Focus error waveform check

(DRF is ignored during search mode.)

3 Play Mode PLAY button Normal • Normal playback • Each servo circuit check

• If TOC READ is unavailable, • DRF check focus search is continued.

4 Traverse PAUSE Normal • Tracking servo OFF/ON • Tracking balance check

Mode button OFF and ON is repeated by every

press of the PAUSE button.

5 Sled mode FF button TEST • PU moves to the innermost position. *3

At the same time, lens is kicked toward inner position.

RWD button TEST • PU moves to the outermost position. *3

At the same time, lens is kicked toward outer position.

6 Spindle mode All lit. • When the button is pressed at the first • Spindle circuit check

* 1 … When Focus Search operates continuously more than 10 minutes, the protection circuit is activated due to heat generation of the driver IC.

In this case, turn off the power, wait for approximately 10 minutes so that heat is released, and then restart.

* 2 … When Focus Search fails three times, the gain is switched for CD-RW at the fourth time.

* 3 … Be careful not to damage the gear because the sled motor rotates while the FF or RWD button is being pressed even if the pickup is located in

the innermost track or the outermost track.

REC/ REC MUTE button

time, spindle motor rotates forward (at rough speed). At the second press, rotation is reversed. At the third press, rotation stops.

• Sled circuit check

• Tracking circuit check

• Mechanism movement check

• PU check

• Spindle motor check

– 42 –

MECHANICAL EXPLODED VIEW

– 43 –

MECHANICAL PARTS LIST

! = ! SAFTY PARTS C = Components marked

UNIT-NAME ! C REF-NO PARTS-NO PARTS-NAME SUFFIX&MODEL

CX-NR11 EZSC1 O MC1001 8A-NF8-282-010 SPR-T,EJECT 2 a O MC1002 8A-NF8-281-010 SPR-T,EJECT 1 a O MC1003 8C-NFA-006-010 BOX,CASS 2 a O MC1004 8C-NFA-005-010 BOX,CASS 1 a O MC1005 8C-NF8-006-010 WINDOW,CASS 2 a O MC1006 8C-NF8-005-010 WINDOW,CASS 1 a O MC1007 8C-NF9-001-010 KNOB,RTRY VOL a X MC1008 8C-NF8-235-010 CHAS,MAIN CC 57-35 a O MC1009 8C-NF8-027-010 KNOB,RTRY JOG a O MC1010 8C-NFA-032-010 PANEL,RIGHT a

O MC1011 8C-NFA-004-010 CABI,ASSY FR EZR a X MC1011a 8C-NFA-008-010 KEY,POWER a X MC1011b 8C-NFA-003-010 PANEL,FR EZR a X MC1011c 8C-NFA-001-010 CABI,FR EZ a O MC1012 8Z-NF6-210-010 DMPR,150 N a O MC1013 8C-NFA-007-010 WINDOW,DISP EZR a O MC1014 8C-NFA-031-010 PANEL,LEFT a O MC1015 8C-NFA-033-010 PANEL,TOP a O MC1016 8C-NF8-029-010 KEY,REC EZ a O MC1017 8C-NF7-009-010 KEY,RDS W/O AG a

CX-NR11 EZSC1 O MC1018 8C-NF8-013-010 KEY,OPE a O MC1019 8C-NF8-010-010 KEY,CD a O MC1020 8C-NF8-011-010 KEY,ENTER a X MC1021 8C-NFA-639-010 PWB,HP (RDS) a O MC1022 87-NF4-216-010 HLDR,LOCK 1 a O MC1023 86-NF9-224-010 SPR-C,LOCK a O MC1024 82-NF5-229-010 PLATE,LOCK(*) a X MC1025 8C-NF9-201-010 PLATE,EARTH MECHA a O MC1026 87-NF4-217-110 HLDR,LOCK 2 a X MC1027 M8-CZK-292-070 CMAT6Z2(1+1)ALPS a

O MC1028 87-A90-193-010 HLDR,CV100 (B) a O MC1029 88-908-301-110 FF-CABLE,8P 1.25 300MM a O MC1030 88-911-101-110 FF-CABLE,11P 1.25 100MM a O MC1031 8A-NFA-208-010 GUIDE,FL 100-25 ANFA a X MC1032 8C-NF9-621-010 PWB,FRONT CNF-9 a O MC1033 87-B00-002-010 BADGE,AIWA 30 ABS SIL a O MC1034 8C-NFA-009-010 PANEL,TRAY a X MC1035 M8-BZG-29J-070 BZG-2 ZD9GNC1 a O MC1036 8A-NF8-206-010 HLDR,PWB M a O MC1037 8C-NF9-606-010 CONN ASSY,8P -RPB a

CX-NR11 EZSC1 O MC1038 8C-NF9-605-010 CONN ASSY,3P -PB a X MC1039 8C-ZA3-618-010 SHLD-CASE,CZA-3 EZ S a X MC1040 8C-NFA-637-010 PWB,MAIN (RDS) a X MC1041 8C-NF9-623-010 PWB,HLDR WIRE CNF-9 a X MC1042 8C-NF9-619-010 SHILD-CASE,CNF9 EZ P a O MC1043 88-906-251-110 FF-CABLE,6P 1.25 a X MC1044 8C-NFA-201-010 HT-SINK,TR C a O MC1045 8C-NFA-002-010 CABI,REAR EZSC a X MC1046 8C-NFA-638-010 PWB,PT (RDS) a ! O MC1047 8C-NFA-601-010 PT,CNF-A EZ a

! O MC1048 87-A80-143-010 AC CORD ASSY,E BLK a O MC1049 87-085-185-010 BUSHING,AC CORD(E) CM-22B a O MC1050 8C-NF9-615-010 FL,HUA-13SS09T a O MC1A 87-B10-091-010 UTT2+3-10 W/O SLOT BLK a O MC1B 87-721-096-410 QT2+3-10 W/O SLOT a O MC1C 87-067-001-010 S-SCREW,BVWWST2+3-12 W/O SLOT a O MC1D 88-AR1-217-010 S-SCREW,BFT2+3-8 a O MC1E 87-078-200-010 S-SCREW,ITC+4-8 R a O MC1F 87-067-703-010 BVT2+3-10 W/0 SL0T a O MC1G 87-NF4-224-010 S-SCREW,IT3B+3-8 CU a

All components used on this model at the production line are shown in this service manual. However, please note that not all components will be available as spare parts for after-sales service. Components marked S and O are designated as spare parts for service and will be stocked at the spare parts centers. Components marked X and R are not designated as spare parts for after sales service, and will not be stocked at the spare parts centers.

– 44 –

COLOR NAME TABLE

Basic color symbol Color Basic color symbol Color Basic color symbol Color

B Black C Cream D Orange

G Green H Gray L Blue

LT Transparent Blue N Gold P Pink

R Red S Silver ST Titan Silver T Brown V Violet W White

WT Transparent White Y Yellow YT Transparent Yellow

LM Metallic Blue LL Light Blue GT Transparent Green LD Dark Blue DT Transparent Orange GM Metallic Green

YM Metallic Yellow DM Metallic Orange PT Transparent Pink

LA Aqua Blue GL Light Green HT Transparent Gray

HM Metallic Gray NH Champagne Gold M Wood Pattern

– 45 –

TAPE MECHANISM EXPLODED VIEW

8

3

2

7

5

4

7

6

9

10

1

– 46 –

TAPE MECHANISM PARTS LIST

! = ! SAFTY PARTS C = Components marked

UNIT-NAME ! C REF-NO PARTS-NO PARTS-NAME SUFFIX&MODEL

CMAT6Z2(1+1) ALPS O TC1001 SF-513-888-000 PLATE HD BLK a O TC1002 SF-525-349-000 MTR MAIN BLK a O TC1003 SF-567-700-000 PCB CONTROL BLK a O TC1004 SF-522-063-000 CLUTCH ASSY BLK a O TC1005 SF-F19-N31-000 MAIN BELT a O TC1006 SF-514-135-000 ROLLER PINCH R BLK a O TC1007 SF-F19-S31-000 F/R BELT a O TC1008 SF-F19-N22-000 MAIN BELT a O TC1009 SF-513-889-000 PLATE HD BLK a O TC1010 M8-CZK-292-070 CMAT6Z2(1+1)ALPS a

All components used on this model at the production line are shown in this service manual. However, please note that not all components will be available as spare parts for after-sales service. Components marked S and O are designated as spare parts for service and will be stocked at the spare parts centers. Components marked X and R are not designated as spare parts for after sales service, and will not be stocked at the spare parts centers.

– 47 –

AIWA NSX-R1 Service Manual

Specifications and Main Features

Frequently Asked Questions

User Manual