This Service Manual is the "Revision Publishing" and replaces "Simple Manual"
(S/M Code No. 09-002-429-5T1).
If requiring information about the CD mechanism, see Service Manual of
AZG-1 ZD8RDC (S/M Code No. 09-001-335-3NA)/
AZG-1 YKZD8RDF (S/M Code No. 09-001-335-3N6).
CD
CASSEIVER
CX–NBL54
BASIC TAPE MECHANISM : ZZM-3 PR1NF(U)
BASIC CD MECHANISM : AZG-1 ZD8RDC(LH)
BASIC CD MECHANISM : AZG-1 YKZD8RDF(U)
SPEAKER
SX–WNBL53
REMOTE
CONTROLLER
RC–ZAS01
RC–ZAS02
S/M Code No. 09-002-429-5R3
REVISION
DATA
SPECIFICATIONS
Main unit CX-NBL54/CX-NAJ54
FM tuner section
Tuning range87.5 MHz to 108 MHz
Usable sensitivity (IHF)13.2 dBf
Antenna terminal75 ohms (unbalanced)
AM tuner section
Tuning range530 kHz to 1710 kHz (10 kHz step)
531 kHz to 1602 kHz (9 kHz step)
Usable sensitivity350 µV/m
AntennaLoop antenna
Amplifier section
Mid-high frequency amplifier
Power outputRated: 20 W + 20 W (8 ohms,
T.H.D. 1 %, 1 kHz) <LH>
Reference : 25 W + 25 W (8 ohms,
T.H.D. 10 %, 1 kHz) <LH>
20 W + 20 W (200 Hz - 20kHz, THD
less than 1%, 8 ohms) <U>
Total harmonic distortion 0.1 % (10 W, 1 kHz, 8 ohms, DIN
AUDIO)
Low frequency amplifier
Power outputRated: 60 W + 60 W (6 ohms,
T.H.D. 1 %, 130 Hz) <LH>
Reference : 75 W + 75 W (6 ohms,
T.H.D. 10 %, 130 Hz) <LH>
60 W + 60 W (50 Hz - 200 Hz, THD
less than 1%, 6 ohms) <U>
Total harmonic distortion 0.1 % (30W, 130 Hz, 6 ohms, DIN
AUDIO)
InputsVIDEO/AUX: 500 mV
MIC1.0 mV (10 k ohms) <LH>
OutputsSPEAKERS HIGH FREQ:
accept speakers of 8 ohms or more
SPEAKERS LOW FREQ:
accept speakers of 6 ohms or more
SURROUND SPEAKERS:
accept speakers of 8 ohms to 16
ohms
PHONES (stereo jack): accepts
headphones of 32 ohms or more
Cassette deck section
Track format4 tracks, 2 channels stereo
Frequency response50 Hz – 15000 Hz
Recording systemAC bias
HeadsDeck 1: Playback head x 1
Deck 2: Recording/playback head
x 1, erase head x 1
Compact disc player section
LaserSemiconductor laser (λ = 780 nm)
D-A converter1 bit dual
Signal-to-noise ratio85 dB (1 kHz, 0 dB)
Harmonic distortion0.05 % (1 kHz, 0 dB)
Wow and flutterUnmeasurable
General
Power requirements120 V/220 – 230 V/240 V AC,
switchable 50/60 Hz <LH>
120 V AC, 60 Hz <U>
Power consumption130 W <LH>, 110 W <U>
Power consumption in standby mode
If the power-economizing mode is
ECO OFF: 20 W
If the power-economizing mode is
ECO ON or ECO AUTO: 0.9 W
Dimensions of main unit260 x 326 x 346 mm
(W x H x D)(10 1/4 x 127/8 x 135/8 in.)
Weight of main unit9.0 kg <LH>
8.0 kg (17 lbs 10 oz.) <U>
Speaker system SX-WNBL53/SX-WNAJ53
Speaker system3 way, Built-in subwoofer (magnetic
shielded type)
Speaker unitsSubwoofer: 160 mm (63/8 in.)
cone type
Full range: 100 mm (4 in.)cone type
Super tweeter: 20 mm (13/16 in.)
ceramic type
Impedance6 ohms/8 ohms
Sensitvity87 dB/W/m
Dimensions (W x H x D)230 x 324 x 282 mm
(91/8 x 127/8 x 111/8 in.)
Weight4.8 kg (10 lbs 9 oz)
• Design and specifications are subject to change without notice.
• The word “BBE” and the “BBE symbol” are trademarks of BBE
Sound, Inc.
PROTECTION OF EYES FROM LASER BEAM DURING SERVICING
This set employs laser. Therefore, be sure to follow carefully the
instructions below when servicing.
WARNING!
WHEN SERVICING, DO NOT APPROACH THE LASER EXIT
WITH THE EYE TOO CLOSELY. IN CASE IT IS NECESSARY TO
CONFIRM LASER BEAM EMISSION. BE SURE TO OBSERVE
FROM A DISTANCE OF MORE THAN 30cm FROM THE
SURFACE OF THE OBJECTIVE LENS ON THE OPTICAL
PICK-UP BLOCK.
Caution: Invisible laser radiation when
open and interlocks defeated avoid exposure to beam.
Advarsel:Usynling laserståling ved åbning,
når sikkerhedsafbrydere er ude af funktion.
Undgå udsættelse for stråling.
VAROITUS!
Laiteen Käyttäminen muulla kuin tässä käyttöohjeessa mainitulla tavalla saattaa altistaa käyt-täjän turvallisuusluokan 1 ylittävälle näkymättömälle lasersäteilylle.
VARNING!
Om apparaten används på annat sätt än vad som specificeras i
denna bruksanvising, kan användaren utsättas för osynling
laserstrålning, som överskrider gränsen för laserklass 1.
CAUTION
Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous
radiation exposure.
ATTENTION
L'utilisation de commandes, réglages ou procédures autres que
ceux spécifiés peut entraîner une dangereuse exposition aux
radiations.
ADVARSEL!
Usynlig laserståling ved åbning, når sikkerhedsafbrydereer ude
af funktion. Undgå udsættelse for stråling.
This Compact Disc player is classified as a CLASS 1 LASER
product.
The CLASS 1 LASER PRODUCT label is located on the rear
exterior.
CLASS 1
KLASSE 1
LUOKAN 1
KLASS 1
ZA3/ZA4 (KSS-213F) MODEL
LASER PRODUCT
LASER PRODUKT
LASER LAITE
LASER APPARAT
Precaution to replace Optical block
Body or clothes electrostatic potential could ruin
laser diode in the optical block. Be sure ground
body and workbench, and use care the clothes
do not touch the diode.
1) After the connection, remove solder shown in
the figure below.
ZA8/ZD8 MODEL
Solder
3
NOTE ON BEFORE STARTING REPAIR
1. Forced discharge of electrolytic capacitor of power supply block
When repair is going to be attempted in the set that uses relay circuit in the power supply block, electric potential is kept charged across
the electrolytic capacitors (C101, 102) even though AC power cord is removed. If repair is attempted in this condition, secondary defect
can occur.
In order to prevent the secondary trouble, perform the following measures before starting repair work.
Discharge procedure
1Remove the AC power cord.
2Connect a discharging resistor at an end of lead wire that
has clips at both ends. Connect the other end of the lead
wire to metal chassis.
3Contact the other end of the discharging resistor to the
positive (+) side (+VH) of C101. (For two seconds)
4Contact the same end of the discharging resistor as step 3
to the negative (-) side (-VH) of C102 in the same way.
(For two seconds)
5Check that voltage across C101 and C102 has decreased
to 1 V or less using a multimeter or an oscilloscope.
Select a discharging resistor referring to the following table.
Chargi n g v o l ta g e ( V )Discharging
(C101, 102)resistor (Ω)
25-48100387-A00-247-090
49-140220587-A00-232-090
Note: The reference numbers (C101, C102) of the electrolytic capacitors can change depending on the models. Be sure to check the
reference numbers of the charging capacitors on schematic diagram before starting the discharging work.
Rated power (W)Parts number
MAIN C.B
D101
3
C101C102
22
4
2. Check items before exchanging the MICROCOMPUTER
Be sure to check the following items before exchanging the MICROCOMPUTER. Exchange the MICROCOMPUTER after confirming
that the MICROCOMPUTER is surely defective.
2-1. Regarding the HOLD terminal of the MICROCOMPUTER
When the HOLD terminal (INPUT) of the MICROCOMPUTER is “H”, the MICROCOMPUTER is judged to be operating correctly.
When this terminal is “L”, the main power cannot be turned on. Therefore, be sure to check the terminal voltage of the HOLD
terminal before exchange.
When the MICROCOMPUTER is not defective, the HOLD terminal can also go “L” when the POWER AMPLIFIER has any
abnormalities that triggers the abnormality detection circuit on the MAIN C. B. that sets the HOLD terminal to “L”.
• Good or no good judgement of the MICROCOMPUTER
1Turn on the AC main power.
2Confirm that the main power is turned on and the HOLD terminal of the MICROCOMPUTER keeps the “H” level or not.
3When the HOLD terminal is “L” level, the abnormality detection circuit is judged to be working correctly and the
MICROCOMPUTER is judged to be good.
4
In such a case, check also if the POWER AMPLIFIER circuit or power supply circuit has any abnormalities or not.
2-2. Regarding reset
There are cases that the machine does not work correctly because the MICROCOMPUTER is not reset even though the AC power
cord is re-inserted, or the software reset (pressing the STOP key + POWER key) is performed.
When the above described phenomenon occurs, it can lead to wrong judgement as if the MICROCOMPUTER is defective and to
exchange the MICROCOMPUTER. In such a case, perform the forced-reset by the following procedure and check good or no
good of the MICROCOMPUTER.
1 Remove the AC power cord.
FRONT C.B
18
MICROCOMPUTER
15
C113
C113
15
18
VSS
VDD
MICROCOMPUTER
FRONT C.B
Short with tweezers.
Fig-2-2
2Short both ends of the electrolytic capacitor C113 that is connected to VDD of the MICROCOMPUTER with tweezers.
3Connect the AC power cord again. If the MICROCOMPUTER returns to the normal operation, the MICROCOMPUTER is
good.
Note: The reference number or MICROCOMPUTER pin number of transistor (Q110) and electrolytic capacitor (C113) can change depending
on the models. Be sure to check the reference numbers on schematic diagram before starting the discharging work.
2-3. Confirmation of soldering state of MICROCOMPUTER
Check the soldering state of the MICROCOMPUTER in addition to the above described procedures. Be sure to exchange the
MICROCOMPUTER after surely confirming that the trouble is not caused by poor soldering but the MICROCOMPUTER itself.
C0004 87-012-368-080 C-CAP,S 0.1-50 Z F
C0005 87-012-368-080 C-CAP,S 0.1-50 Z F
C0006 87-012-368-080 C-CAP,S 0.1-50 Z F
C0009 87-012-368-080 C-CAP,S 0.1-50 Z F
C0010 87-012-368-080 C-CAP,S 0.1-50 Z F
NO.
REF. NOPART NO.KANRIDESCRIPTION
C0011 87-012-368-080 C-CAP,S 0.1-50 Z F
C0012 87-012-368-080 C-CAP,S 0.1-50 Z F
C0015 87-012-368-080 C-CAP,S 0.1-50 Z F
C0016 87-012-368-080 C-CAP,S 0.1-50 Z F
C0017 87-012-368-080 C-CAP,S 0.1-50 Z F
C0018 87-012-368-080 C-CAP,S 0.1-50 Z F
C0019 87-016-520-000 CAP,E 3300-65 M SMG
C0020 87-016-520-000 CAP,E 3300-65 M SMG
C0021 87-016-051-000 CAP,E 2200-35 M SMG
C0022 87-016-051-000 CAP,E 2200-35 M SMG
C0023 87-016-658-000 CAP,E 4700-35 M SMG
C0024 87-016-658-000 CAP,E 4700-35 M SMG
C0025 87-010-408-080 CAP,E 47-50 M 11L SME
C0026 87-010-247-080 CAP,E 100-50 M SME
C0030 87-010-430-080 CAP,E 100-63
C0031 87-010-263-080 CAP,E 100-10 M 11L SME
C0032 87-010-197-080 C-CAP,S 0.01-25 K B C2012
C0033 87-010-263-080 CAP,E 100-10 M 11L SME<U>
C0034 87-010-260-080 CAP,E 47-25 M 11L SME
C0035 87-010-380-080 CAP,E 47-16 M 11L SME
C0036 87-010-381-080 CAP,E 330-16 M SME
C0038 87-010-197-080 C-CAP,S 0.01-25 K B C2012
C0060 87-010-403-080 CAP,E 3.3-50 M 11L SME
C0061 87-010-260-080 CAP,E 47-25 M 11L SME
C0101 87-010-183-080 C-CAP,S 2700P-50 K B GRM
C0102 87-010-183-080 C-CAP,S 2700P-50 K B GRM
C0103 87-010-545-080 CAP,E 0.22-50 M 11L SME
C0104 87-010-545-080 CAP,E 0.22-50 M 11L SME
C0107 87-010-405-080 CAP,E 10-50 M 11L SME
C0108 87-010-405-080 CAP,E 10-50 M 11L SME
C0111 87-010-405-080 CAP,E 10-50 M 11L SME
C0112 87-010-405-080 CAP,E 10-50 M 11L SME
C0113 87-010-866-080 CAP,E 10-63 M VX
C0114 87-010-866-080 CAP,E 10-63 M VX
C0119 87-010-197-080 C-CAP,S 0.01-25 K B C2012
C0120 87-010-197-080 C-CAP,S 0.01-25 K B C2012
C0125 87-012-368-080 C-CAP,S 0.1-50 Z F
C0126 87-012-368-080 C-CAP,S 0.1-50 Z F
C0127 87-012-368-080 C-CAP,S 0.1-50 Z F
C0128 87-012-368-080 C-CAP,S 0.1-50 Z F
C0133 87-010-186-080 C-CAP,S 4700P-50 K B C2012
C0140 87-010-182-080 C-CAP,S 2200P-50 K B C2012
C0141 87-010-196-080 C-CAP,S 0.1-25 Z F C2012
C0203 87-010-182-080 C-CAP,S 2200P-50 K B C2012
C0204 87-010-182-080 C-CAP,S 2200P-50 K B C2012
C0205 87-012-140-080 C-CAP,S 470P-50 J CH
C0206 87-012-140-080 C-CAP,S 470P-50 J CH
C0209 87-010-402-080 CAP,E 2.2-50 M 11L SME
C0210 87-010-402-080 CAP,E 2.2-50 M 11L SME
C0211 87-010-184-080 C-CAP,S 3300P-50 K B C2012
C0212 87-010-184-080 C-CAP,S 3300P-50 K B C2012
C0213 87-010-402-080 CAP,E 2.2-50 M 11L SME
C0214 87-010-402-080 CAP,E 2.2-50 M 11L SME
C0217 87-010-405-080 CAP,E 10-50 M 11L SME
C0218 87-010-405-080 CAP,E 10-50 M 11L SME
C0220 87-010-405-080 CAP,E 10-50 M 11L SME
C0223 87-010-190-080 C-CAP,S 0.01-50 Z F C2012
C0224 87-010-190-080 C-CAP,S 0.01-50 Z F C2012
C0228 87-010-405-080 CAP,E 10-50 M 11L SME
C0229 87-010-196-080 C-CAP,S 0.1-25 Z F C2012
C0230 87-010-196-080 C-CAP,S 0.1-25 Z F C2012
C0231 87-010-196-080 C-CAP,S 0.1-25 Z F C2012
C0232 87-010-196-080 C-CAP,S 0.1-25 Z F C2012
C0239 87-010-196-080 C-CAP,S 0.1-25 Z F C2012
C0301 87-010-178-080 C-CAP,S 1000P-50 K B C2012
C0302 87-010-178-080 C-CAP,S 1000P-50 K B C2012
C0303 87-010-178-080 C-CAP,S 1000P-50 K B C2012
C0304 87-010-178-080 C-CAP,S 1000P-50 K B C2012
C0307 87-010-263-080 CAP,E 100-10 M 11L SME
C0308 87-010-263-080 CAP,E 100-10 M 11L SME
NO.
6
REF. NOPART NO.KANRIDESCRIPTION
C0309 87-010-318-080 C-CAP,S 47P-50 J CH GRM
C0310 87-010-318-080 C-CAP,S 47P-50 J CH GRM
C0313 87-010-188-080 C-CAP,S 6800P-50 K B C2012
C0314 87-010-188-080 C-CAP,S 6800P-50 K B C2012
C0315 87-010-263-080 CAP,E 100-10 M 11L SME
C0317 87-010-546-080 CAP,E 0.33-50 M 11L SME
C0318 87-010-546-080 CAP,E 0.33-50 M 11L SME
C0326 87-010-198-080 C-CAP,S 0.022-25 K B C2012
C0327 87-012-368-080 C-CAP,S 0.1-50 Z F
C0360 87-010-401-080 CAP,E 1-50 M 11L SME
C0399 87-012-140-080 C-CAP,S 470P-50 J CH
C0401 87-010-544-080 CAP,E 0.1-50 M 11L SME
C0402 87-010-544-080 CAP,E 0.1-50 M 11L SME
C0403 87-010-321-080 C-CAP,S 82P-50 J CH
C0404 87-010-321-080 C-CAP,S 82P-50 J CH
C0405 87-010-197-080 C-CAP,S 0.01-25 K B C2012
C0406 87-010-197-080 C-CAP,S 0.01-25 K B C2012
C0407 87-010-197-080 C-CAP,S 0.01-25 K B C2012
C0408 87-010-197-080 C-CAP,S 0.01-25 K B C2012
C0409 87-010-182-080 C-CAP,S 2200P-50 K B C2012
C0410 87-010-182-080 C-CAP,S 2200P-50 K B C2012
C0411 87-010-405-080 CAP,E 10-50 M 11L SME
C0412 87-010-405-080 CAP,E 10-50 M 11L SME
C0452 87-010-382-080 CAP,E 22-25 M 11L SME
C0453 87-010-183-080 C-CAP,S 2700P-50 K B GRM
C0454 87-010-183-080 C-CAP,S 2700P-50 K B GRM
C0455 87-010-183-080 C-CAP,S 2700P-50 K B GRM
C0456 87-010-197-080 C-CAP,S 0.01-25 K B C2012
C0458 87-010-178-080 C-CAP,S 1000P-50 K B C2012
C0459 87-010-175-080 C-CAP,S 560P-50 J SL
C0460 87-010-196-080 C-CAP,S 0.1-25 Z F C2012
C0461 87-012-158-080 C-CAP,S 390P-50 J CH GRM
C0462 87-012-158-080 C-CAP,S 390P-50 J CH GRM
C0507 87-010-196-080 C-CAP,S 0.1-25 Z F C2012
C0508 87-010-178-080 C-CAP,S 1000P-50 K B C2012
C0519 87-010-401-080 CAP,E 1-50 M 11L SME
C0520 87-010-401-080 CAP,E 1-50 M 11L SME
C0521 87-010-546-080 CAP,E 0.33-50 M 11L SME
C0522 87-010-546-080 CAP,E 0.33-50 M 11L SME
C0523 87-010-545-080 CAP,E 0.22-50 M 11L SME
C0524 87-010-545-080 CAP,E 0.22-50 M 11L SME
C0525 87-010-545-080 CAP,E 0.22-50 M 11L SME
C0526 87-010-545-080 CAP,E 0.22-50 M 11L SME
C0605 87-010-179-080 C-CAP,S 1200P-50 K B GRM
C0606 87-010-179-080 C-CAP,S 1200P-50 K B GRM
C0609 87-010-213-080 C-CAP,S 0.015-25 K B GRM
C0610 87-010-213-080 C-CAP,S 0.015-25 K B GRM
C0611 87-010-545-080 CAP,E 0.22-50 M 11L SME
C0612 87-010-545-080 CAP,E 0.22-50 M 11L SME
C0613 87-010-545-080 CAP,E 0.22-50 M 11L SME
C0614 87-010-545-080 CAP,E 0.22-50 M 11L SME
C0615 87-010-154-080 C-CAP,S 10P-50 D CH GRM
C0616 87-010-385-080 CAP,E 220-25 M SME
C0617 87-010-385-080 CAP,E 220-25 M SME
C0618 87-010-405-080 CAP,E 10-50 M 11L SME
C0620 87-010-263-080 CAP,E 100-10 M 11L SME
C0630 87-016-669-080 C-CAP,S 0.1-25 K B
C0631 87-010-185-080 C-CAP,S 3900P-50 K B
C0632 87-010-185-080 C-CAP,S 3900P-50 K B
C0633 87-016-369-080 C-CAP,S 0.033-25 K B GRM
C0634 87-016-369-080 C-CAP,S 0.033-25 K B GRM
C0661 87-010-178-080 C-CAP,S 1000P-50 K B C2012
C0662 87-010-178-080 C-CAP,S 1000P-50 K B C2012
C0671 87-010-196-080 C-CAP,S 0.1-25 Z F C2012<LH>
C0672 87-010-196-080 C-CAP,S 0.1-25 Z F C2012<LH>
NO.
REF. NOPART NO.KANRIDESCRIPTION
C0673 87-010-182-080 C-CAP,S 2200P-50 K B C2012<LH>
C0677 87-010-197-080 C-CAP,S 0.01-25 K B C2012
C0771 87-010-263-080 CAP,E 100-10 M 11L SME
C0772 87-010-197-080 C-CAP,S 0.01-25 K B C2012
C0782 87-010-197-080 C-CAP,S 0.01-25 K B C2012
C0783 87-010-197-080 C-CAP,S 0.01-25 K B C2012
C0784 87-010-197-080 C-CAP,S 0.01-25 K B C2012
C0785 87-010-197-080 C-CAP,S 0.01-25 K B C2012
C0786 87-010-197-080 C-CAP,S 0.01-25 K B C2012
C0788 87-010-149-080 C-CAP,S 5P-50 C CH GRM
C0789 87-A12-052-080 C-CAP,S 0.033-25 J B
C0790 87-A12-052-080 C-CAP,S 0.033-25 J B
C0791 87-010-196-080 C-CAP,S 0.1-25 Z F C2012
C0792 87-010-197-080 C-CAP,S 0.01-25 K B C2012
C0793 87-010-404-080 CAP,E 4.7-50 M 11L SME
C0795 87-010-197-080 C-CAP,S 0.01-25 K B C2012
C0796 87-010-197-080 C-CAP,S 0.01-25 K B C2012
C0797 87-010-405-080 CAP,E 10-50 M 11L SME
C0798 87-010-197-080 C-CAP,S 0.01-25 K B C2012
C0799 87-010-407-080 CAP,E 33-50 M 11L SME
C0800 87-012-369-080 C-CAP,S 0.047-50 Z F
C0801 87-010-403-080 CAP,E 3.3-50 M 11L SME
C0802 87-010-194-080 C-CAP,S 0.047-25 Z F
C0803 87-010-198-080 C-CAP,S 0.022-25 K B C2012
C0804 87-010-263-080 CAP,E 100-10 M 11L SME
C0807 87-010-400-080 CAP,E 0.47-50 M 11L SME
C0808 87-010-401-080 CAP,E 1-50 M 11L SME
C0809 87-010-401-080 CAP,E 1-50 M 11L SME
C0810 87-010-196-080 C-CAP,S 0.1-25 Z F C2012
C0814 87-010-197-080 C-CAP,S 0.01-25 K B C2012
C0815 87-010-400-080 CAP,E 0.47-50 M 11L SME
C0816 87-010-400-080 CAP,E 0.47-50 M 11L SME
C0821 87-010-405-080 CAP,E 10-50 M 11L SME
C0823 87-010-177-080 C-CAP,S 820P-50 J SL C2012
C0824 87-010-405-080 CAP,E 10-50 M 11L SME
C0825 87-010-596-080 C-CAP,S 0.047-16 K R C2012
C0842 87-010-197-080 C-CAP,S 0.01-25 K B C2012
C0844 87-010-197-080 C-CAP,S 0.01-25 K B C2012
C0850 87-010-260-080 CAP,E 47-25 M 11L SME
C0851 87-010-197-080 C-CAP,S 0.01-25 K B C2012
C0852 87-010-197-080 C-CAP,S 0.01-25 K B C2012
C0853 87-010-197-080 C-CAP,S 0.01-25 K B C2012
C0858 87-010-196-080 C-CAP,S 0.1-25 Z F C2012
C0859 87-010-196-080 C-CAP,S 0.1-25 Z F C2012
C0860 87-010-197-080 C-CAP,S 0.01-25 K B C2012
C0959 87-010-196-080 C-CAP,S 0.1-25 Z F C2012
C0960 87-010-196-080 C-CAP,S 0.1-25 Z F C2012
C0961 87-010-152-080 C-CAP,S 8P-50 D CH GRM
C0963 87-015-785-080 C-CAP, 0.1-25 Z F C3216
C0971 87-010-381-080 CAP,E 330-16 M SME
C0972 87-010-404-080 CAP,E 4.7-50 M 11L SME
C0973 87-010-197-080 C-CAP,S 0.01-25 K B C2012
C0974 87-010-197-080 C-CAP,S 0.01-25 K B C2012
C0979 87-010-322-080 C-CAP,S 100P-50 J CH GRM
C0981 87-010-260-080 CAP,E 47-25 M 11L SME
C0982 87-010-196-080 C-CAP,S 0.1-25 Z F C2012
C0983 87-010-197-080 C-CAP,S 0.01-25 K B C2012
C0984 87-010-197-080 C-CAP,S 0.01-25 K B C2012
C0987 87-010-197-080 C-CAP,S 0.01-25 K B C2012
C0991 87-010-312-080 C-CAP,S 15P-50 J CH GRM
C0992 87-010-312-080 C-CAP,S 15P-50 J CH GRM
C0993 87-010-178-080 C-CAP,S 1000P-50 K B C2012
C0995 87-010-178-080 C-CAP,S 1000P-50 K B C2012
C0997 87-010-196-080 C-CAP,S 0.1-25 Z F C2012
C0998 87-010-260-080 CAP,E 47-25 M 11L SME
C0999 87-A11-132-080 CAP,TC U 0.01-50 K B
CF0831 87-008-261-010 FLTR,CF SFE10.7MA5
CF0832 87-008-261-010 FLTR,CF SFE10.7MA5
CN0301 87-A60-620-010 CONN,3P V 2MM JMT
CN0351 87-A60-625-010 CONN,8P V 2MM JMT
NO.
7
REF. NOPART NO.KANRIDESCRIPTION
NO.
CN0601 87-099-719-010 CONN,30P H BLK TYK-B(X)
CN0602 87-A60-131-010 CONN,6P V FE
CNA0001 8A-NF8-654-010 CONN ASSY,11P TID-A(480)
FFC602 88-906-251-110 FF-CABLE,6P 1.25
FFE0831 A8-8ZA-191-030 8ZA-1 YFEUNM<U>
C0211 87-010-322-080 C-CAP,S 100P-50 J CH GRM
C0251 87-010-405-040 CAP,E 10-50 M 11L SME
C0253 87-010-196-080 C-CAP,S 0.1-25 Z F C2012
C0254 87-012-369-080 C-CAP,S 0.047-50 Z F
C0255 87-010-560-040 CAP,E 10-50 M 5L MA
C0256 87-010-405-040 CAP,E 10-50 M 11L SME
C0259 87-010-405-040 CAP,E 10-50 M 11L SME
C0264 87-A11-148-080 CAP,TC U 0.1-50 Z F
C0273 87-010-178-080 C-CAP,S 1000P-50 K B C2012
C0274 87-010-178-080 C-CAP,S 1000P-50 K B C2012
C0301 87-010-182-080 C-CAP,S 2200P-50 K B C2012
C0302 87-010-196-080 C-CAP,S 0.1-25 Z F C2012
C0303 87-010-196-080 C-CAP,S 0.1-25 Z F C2012
C0312 87-010-498-040 CAP,E 10-16 M 5L SRE
C0314 87-010-196-080 C-CAP,S 0.1-25 Z F C2012
REF. NOPART NO.KANRIDESCRIPTION
C0315 87-010-196-080 C-CAP,S 0.1-25 Z F C2012
C0316 87-010-196-080 C-CAP,S 0.1-25 Z F C2012
C0321 87-012-393-080 C-CAP,S 0.22-16 K W5R CM/CB
C0322 87-010-400-040 CAP,E 0.47-50 M 11L SME
C0325 87-A10-189-040 CAP,E 220-10 M 5L
C0339 87-012-156-080 C-CAP,S 220P-50 J CH GRM
C0340 87-010-197-080 C-CAP,S 0.01-25 K B C2012
C0341 87-010-194-080 C-CAP,S 0.047-25 Z F
C0351 87-010-981-040 CAP,E 22-35 M 5L SRE
C0401 87-010-197-080 C-CAP,S 0.01-25 K B C2012
C0451 87-010-196-080 C-CAP,S 0.1-25 Z F C2012
C0452 87-010-196-080 C-CAP,S 0.1-25 Z F C2012
C0453 87-010-196-080 C-CAP,S 0.1-25 Z F C2012
C0454 87-010-196-080 C-CAP,S 0.1-25 Z F C2012
C0455 87-010-196-080 C-CAP,S 0.1-25 Z F C2012
C0502 87-010-186-080 C-CAP,S 4700P-50 K B C2012<LH>
C0503 87-010-112-040 CAP,E 100-16 M 11L SME<LH>
C0504 87-010-405-040 CAP,E 10-50 M 11L SME<LH>
C0505 87-010-545-040 CAP,E 0.22-50 M 11L SME<LH>
C0506 87-010-320-080 C-CAP,S 68P-50 J CH GRM<LH>
C0507 87-010-544-040 CAP,E 0.1-50 M 11L SME<LH>
C0508 87-010-544-040 CAP,E 0.1-50 M 11L SME<LH>
C0510 87-010-322-080 C-CAP,S 100P-50 J CH GRM<LH>
C0511 87-010-265-040 CAP,E 33-16 M 11L SME<LH>
C0512 87-010-178-080 C-CAP,S 1000P-50 K B C2012<LH>
C0513 87-010-196-080 C-CAP,S 0.1-25 Z F C2012<LH>
C0515 87-010-178-080 C-CAP,S 1000P-50 K B C2012<LH>
C0602 87-010-322-080 C-CAP,S 100P-50 J CH GRM
C0603 87-010-322-080 C-CAP,S 100P-50 J CH GRM
C0604 87-010-322-080 C-CAP,S 100P-50 J CH GRM
C0650 87-010-196-080 C-CAP,S 0.1-25 Z F C2012
C0699 87-010-196-080 C-CAP,S 0.1-25 Z F C2012
CN0101 87-099-720-010 CONN,30P BLK TYK-B(P)
CN0102 87-099-015-010 CONN,13P V BLK 6216
CN0301 87-A60-140-010 CONN,15P V FE<LH>
CON105 87-099-753-010 CONN,11P 9604 S F<U>
CON105 87-099-756-010 CONN,15P 9604 S F<LH>
SFR1 87-024-581-010 SFR,3.3K DIA 6H
SOL1 82-ZM1-618-410 SOL ASSY,27
SOL2 82-ZM1-618-410 SOL ASSY,27