Page 1
NSX-AJ200
U
NSX-AJ205
NSX-SZ200
NSX-SZ205
U
EZ,LH
EZ
SERVICE MANUAL
COMPACT DISC STEREO SYSTEM
CD
CASSEIVER
NSX–AJ200
(TYPE: U)
NSX–AJ205
(TYPE: U)
NSX–SZ200
(TYPE: EZ)
NSX–SZ205
(TYPE: EZ)
NSX–SZ200
(TYPE: LH)
• This Service Manual is the “Revision Publishing” and replace “Simple Manual”
NSX-AJ200/AJ205/SZ200/SZ205<U,EZ,LH>, (S/M Code No. 09-011-440-9T1).
CX–NAJ205
CX–NSZ200
BASIC CD MECHANISM : BZG-2 ZD4NC
BASIC TAPE MECHANISM: ZZM-3 YPR2NC
SPEAKERSYSTEM
SX–NAJ202CX–NAJ200
SX–NAJ205
SX-R145
SX–NSZ202
SX–NSZ205CX–NSZ205
SX–NSZ205CX–NSZ200
REMOTE
CONTROLLER
RC–AAS11(VS)
• If requiring information about the CD mechanism, see Service Manual of
BZG-2 (S/M Code No. 09-00C-353-2N2).
S/M Code No. 09-012-440-9R1
REVISION
DATA
Page 2
SPECIFICATIONS
TUNER
FM tuning range: 87.5 MHz to 108 MHz
FM usable Sensitivity(IHF):
FM antenna terminals: 75 ohms (unbalanced)
AM tuning range<U,LH>: 530 kHz to 1710 kHz (10 kHz step)
AM usable
sensitivity<U,LH>: 350
AM antenna<U,LH>: Loop antenna
MW tuning range<EZ>: 531 kHz to 1602 kHz (9 kHz step)
MW usable sensitivity<EZ>:
LW tuning range<EZ>: 144 kHz to 290 kHz
LW usable sensitivity: 1400mV/m
MW/LW antenna: Loop antenna
AMPLIFIER
CX-NAJ200
Power output: 20 W + 20 W (50 Hz - 20 kHz, THD
Total
harmonic distortion:
CX-NAJ205
Power output: 40 W + 40 W (50 Hz - 20 kHz, THD
Total
harmonic distortion:
CX-NSZ200<EZ> / CX-NSZ205
Power output: 12 W + 12 W (6 ohms, T.H.D.
Total
harmonic distortion:
CX-NSZ200<LH>
Power output: Rated: 40 W + 40 W (6 ohms, T.H.D.
Total
harmonic distortion:
Input: VIDEO/AUX: 500 mV
Output: SPEAKERS: 6 ohms or more
CASSETTE DECK
Track format: 4 tracks, 2 channels stereo
Frequency response: 50 Hz - 8 kHz
Recording system: AC bias
Heads: DECK 1: playback x 1
13.2 dBf<U,LH>, 16.8 dBf<EZ>
531 kHz to 1602 kHz (9 kHz step)
mV/m
530 kHz to 1710 kHz (10 kHz step)
350
mV/m
less than 1%, 6 ohms)
25 W + 25 W (1 kHz, THD less than
10%, 6 ohms)
0.1% (10 W, 1 kHz, 6 ohms, DIN AUDIO)
less than 1%, 6 ohms)
50 W + 50 W (1 kHz, THD less than
10%, 6 ohms)
0.1% (20 W, 1 kHz, 6 ohms, DIN AUDIO)
1%, 1 kHz/DIN 45500)
Reference: 15 W + 15 W (6 ohms, T.H.D.
10%, 1 kHz/DIN 45324)
DIN MUSIC POWER: 39 W + 39 W
0.1% (6 W, 1 kHz, 6 ohms, DIN AUDIO)
1%, 1 kHz)
Reference: 50 W + 50 W (6 ohms, T.H.D.
10%, 1 kHz)
0.1% (20 W, 1 kHz, 6 ohms, DIN AUDIO)
SURROUND SPEAKERS (only for
CX-NAJ205): 8 ohms to 16 ohms
PHONES: 32 ohms or more
DECK 2: recording/playback x 1,
erase x 1
FRONT SPEAKERS SX-NAJ202 ( only for NSX-AJ200)
Speaker system: 2 way, bass reflex (magnetic shielded)
Speaker units: Woofer: 120 mm (43/4 in.) cone
Tweeter: 20 mm (13/16 in.) cone
Impedance: 6 ohms
Dimensions (W x H x D): 220 x 324 x 198 mm
( 83/4 x 127/8 x 77/8 in.)
Weight: 2.3 kg (5 lbs 1 oz)
FRONT SPEAKERS SX-NAJ205 ( only for NSX-AJ205)
Speaker system: 3 way, bass reflex (magnetic shielded)
Speaker units: Woofer: 120 mm (43/4 in.) cone
Tweeter: 60 mm (23/8 in.) cone
Super tweeter: 20 mm (13/16 in.)
ceramic
Impedance: 6 ohms
Dimensions (W x H x D): 220 x 324 x 198 mm
( 83/4 x 127/8 x 77/8 in.)
Weight: 2.5 kg (5 lbs 8 oz)
FRONT SPEAKERS SX-NSZ202 ( only for NSX-SZ200<EZ>)
Speaker system: 2 way, bass reflex (magnetic shielded)
Speaker units: Woofer: 120 mm cone
Tweeter: 20 mm ceramic cone
Impedance: 6 ohms
Dimensions (W x H x D): 220 x 324 x 198 mm
Weight: 2.3 kg (5 lbs 1 oz)
FRONT SPEAKERS SX-NSZ205 (for NSX-SZ200<LH>, NSX-SZ205)
Speaker system: 3 way, bass reflex (magnetic shielded)
Speaker units: Woofer: 120 mm cone
Tweeter: 60 mm cone
Super tweeter: 20 mm ceramic
Impedance: 6 ohms
Dimensions (W x H x D): 220 x 324 x 198 mm
Weight: 2.5 kg (5 lbs 8 oz)
SURROUND SPEAKERS SX-R145 (only for NSX-AJ205)
Speaker system: 1 way, bass reflex
Speaker units: Full range: 80 mm(31/4 in.) cone
Impedance: 8 ohms
Dimensions (W x H x D): 100 x 132 x 116 mm
(4 x 51/4 x 45/8 in.)
Weight: 0.5 kg (1 lbs 2 oz)
Accessories: Wall mounting screws (2)
GENERAL
Powerrequirements: 120 V AC, 60 Hz<U>
230 V AC, 50 Hz<EZ>
120 V/220 - 230 V/240 V AC
(Switchable), 50 Hz/60Hz<LH>
Power consumption: 60 W<200U>, 67W<205U>, 53 W<EZ>
70 W<200LH>,
Power consumption
in standby mode: With ECO mode on: 0.6 W
With ECO mode off: 15 W
Dimensions ( W x H x D): 260 x 323 x 291 mm
(101/4 x 123/4 x 111/2 in.)
Weight: 5.9 kg (13 lbs)<U,LH>, 4.9 kg<EZ>
CD PLAYER
Laser: Semiconductor laser (
D/A converter: 1 bit dual
Signal-to-noise ratio: 85 dB (1 kHz, 0 dB)
Harmonic distortion: 0.05 % (1 kHz, 0 dB)
l = 780 nm)
• Design and specifications are subject to change without notice.
– 2 –
Page 3
PROTECTION OF EYES FROM LASER BEAM DURING SERVICING
This set employs laser. Therefore, be sure to follow carefully
the instructions below when servicing.
WARNING!!
WHEN SERVICING, DO NOT APPROACH THE LASER
EXIT WITH THE EYE TOO CLOSELY. IN CASE IT IS
NECESSARY TO CONFIRM LASER BEAM EMISSION.
BE SURE TO OBSERVE FROM A DISTANCE OF MORE
THAN 30cm FROM THE SURFACE OF THE OBJECTIVE
LENS ON THE OPTICAL PICK-UP BLOCK.
Caution: Invisible laser radiation when
open and interlocks defeated avoid
exposure to beam.
s Advarsel: Usynlig laserståling ved åbning,
når sikkerhedsafbrydere er ude af funktion.
Undgå udsættelse for stråling.
VAROITUS!
Laiteen Käyttäminen muulla kuin tässä käyttöohjeessa
mainitulla tavalla saataa altistaa käyt-täjän
turvallisuusluokan 1 ylittävälle näkymättömälle
lasersäteilylle.
VARNING!
Om apparaten används på annat sätt än vad som
specificeras i denna bruksanvising, kan användaren
utsättas för osynling laserstrålning, som överskrider
gränsen för laserklass 1.
CAUTION
Use of controls or adjustments or performance of procedures other than those specified herin may result in
hazardous radiation exposure.
ATTENTION
L’utillisation de commandes, réglages ou procédures
autres que ceux spécifiés peut entraîner une dangereuse
exposition aux radiations.
ADVARSEL
Usynlig laserståling ved åbning, når sikkerhedsafbrydereer
ude af funktion. Undgå udsættelse for stråling.
This Compact Disc player is classified as a CLASS 1
LASER product.
The CLASS 1 LASER PRODUCT label is located on the
rear exterior.
CLASS 1 LASER PRODUCT
KLASSE 1 LASER PRODUKT
LUOKAN 1 LASER LAITE
KLASS 1 LASER APPARAT
Precaution to replace Optical block
(KSS-213F)
Body or clothes electrostatic potential could
ruin laser diode in the optical block. Be sure
ground body and workbench, and use care the
clothes do not touch the diode.
1) After the connection, remove solder shown in
right figure.
PICK-UP ASSY PWB
Solder
– 3 –
Page 4
NOTE ON BEFORE STARTING REPAIR
1. Forced discharge of electrolytic capacitor of power supply block
When repair is going to be attempted in the set that uses relay circuit in the power supply block, electric potential is kept charged across
the electrolytic capacitors (C101, 102) even though AC power cord is removed. If repair is attempted in this condition, secondary defect
can occur.
In order to prevent the secondary trouble, perform the following measures before starting repair work.
Discharge procedure
11
1 Remove the AC power cord.
11
22
2 Connect a discharging resistor at an end of lead wire that
22
has clips at both ends. Connect the other end of the lead
wire to metal chassis.
33
3 Contact the other end of the discharging resistor to the
33
positive (+) side (+VH) of C101. (For two seconds)
44
4 Contact the same end of the discharging resistor as step
44
33
3 to the negative (-) side (-VH) of C102 in the same way.
33
(For two seconds)
55
5 Check that voltage across C101 and C102 has decreased
55
to 1 V or less using a multimeter or an oscilloscope.
Select a discharging resistor referring to the following table.
Charging voltage (V) Discharging
(C101, 102) resistor (Ω)
25-48 100 3 87-A00-247-090
49-140 220 5 87-A00-232-090
Note: The reference numbers (C101, C102) of the electrolytic capacitors can change depending on the models. Be sure to check the
reference numbers of the charging capacitors on schematic diagram before starting the discharging work.
Rated power (W) Parts number
MAIN C.B
D101
3
C101 C102
22
Fig-1
4
2. Check items before exchanging the MICROCOMPUTER
Be sure to check the following items before exchanging the MICROCOMPUTER. Exchange the MICROCOMPUTER after confirming
that the MICROCOMPUTER is surely defective.
2-1. Regarding the HOLD terminal of the MICROCOMPUTER
When the HOLD terminal (INPUT) of the MICROCOMPUTER is “H”, the MICROCOMPUTER is judged to be operating correctly.
When this terminal is “L”, the main power cannot be turned on. Therefore, be sure to check the terminal voltage of the HOLD
terminal before exchange.
When the MICROCOMPUTER is not defective, the HOLD terminal can also go “L” when the POWER AMPLIFIER has any
abnormalities that triggers the abnormality detection circuit on the MAIN C. B. that sets the HOLD terminal to “L”.
• Good or no good judgement of the MICROCOMPUTER
11
1 Turn on the AC main power.
11
22
2 Confirm that the main power is turned on and the HOLD terminal of the MICROCOMPUTER keeps the “H” level or not.
22
33
3 When the HOLD terminal is “L” level, the abnormality detection circuit is judged to be working correctly and the
33
MICROCOMPUTER is judged to be good.
– 4 –
Page 5
In such a case, check also if the POWER AMPLIFIER circuit or power supply circuit has any abnormalities or not.
2-2. Regarding reset
There are cases that the machine does not work correctly because the MICROCOMPUTER is not reset even though the AC power
cord is re-inserted, or the software reset (pressing the STOP key + POWER key) is performed.
When the above described phenomenon occurs, it can lead to wrong judgement as if the MICROCOMPUTER is defective and to
exchange the MICROCOMPUTER. In such a case, perform the forced-reset by the following procedure and check good or no
good of the MICROCOMPUTER.
11
1 Remove the AC power cord.
11
FRONT C.B
18
MICROCOMPUTER
FRONT C.B
22
2 Short both ends of the electrolytic capacitor C113 that is connected to VDD of the MICROCOMPUTER with tweezers.
22
33
3 Connect the AC power cord again. If the MICROCOMPUTER returns to the normal operation, the MICROCOMPUTER is
33
good.
Note: The reference number or MICROCOMPUTER pin number of transistor (Q110) and electrolytic capacitor (C113) can change depending
on the models. Be sure to check the reference numbers on schematic diagram before starting the discharging work.
15
C113
Short with tweezers.
Fig-2-2
C113
%
*
VSS
VDD
MICROCOMPUTER
2-3. Confirmation of soldering state of MICROCOMPUTER
Check the soldering state of the MICROCOMPUTER in addition to the above described procedures. Be sure to exchange the
MICROCOMPUTER after surely confirming that the trouble is not caused by poor soldering but the MICROCOMPUTER itself.
– 5 –
Page 6
ELECTRICAL MAIN PARTS LIST
REF. NO. DESCRIPTIONPART NO. KANRI
IC
87-A21-269-010 IC,EW732
87-A21-893-040 C-IC,NJM4558V-TE2
87-A21-419-040 C-IC,NJM14558MD-TE2
8B-NFA-602-030 IC,UPD780226GF-022-3BA<EXCEPT 205EZ>
8B-NFA-603-030 C-IC,UPD780228GF-079-3BA<205EZ>
87-A21-218-110 IC,NJL64H380A
87-A21-443-040 C-IC,M62495AFP
87-A21-695-010 IC,LA1845L
87-A20-440-040 C-IC,BU1920FS<205EZ>
87-A21-928-010 IC,LC72131D-N
TRANSISTOR
87-A30-494-080 TR,2SA1980G
89-213-702-010 TR,2SB1370 (1.8W)
87-026-610-080 TR,KTC3198GR
87-A30-076-080 C-TR,2SC3052F
87-A30-075-080 C-TR,2SA1235F
87-A30-484-080 C-TR,KRA102S
87-A30-190-080 TR,CC5551
87-A30-255-010 TR,2SB1342<200EZ,205EZ,200U>
87-A30-306-010 TR,2SB1677<200LH>
87-A30-528-010 TR,2SB1686<205U>
87-A30-256-010 TR,2SD1933<200EZ,205EZ,200U>
87-A30-307-010 TR,2SD2619<200LH>
87-A30-529-010 TR,2SD2642<205U>
87-A30-107-070 C-TR,CMBT5401
87-A30-106-040 C-TR,CMBT5551
87-A30-162-010 FET,2SK2937<200LH,205U>
87-A30-091-080 FET,2SJ460
87-A30-090-080 FET,2SK2541
87-A30-062-080 C-TR,KRC104S
87-A30-492-080 TR,2SC5343G
87-A30-468-080 C-TR,KRC102S-RTK
87-A30-582-080 TR,CDA1585BC
87-A30-495-080 TR,2SA1981Y
89-327-143-080 TR,2SC2714 (0.1W)
87-A30-489-080 C-TR,KRA107S
89-503-602-080 C-FET,2SK360E
87-A30-086-040 C-TR,CSD1306E<200EZ,205EZ>
87-A30-234-080 TR,CSC4115BC
DIODE
87-A40-535-080 DIODE,1N5393-GOODARK<200EZ,205EZ>
87-A40-393-090 DIODE,1N5402GW(F20)<200LH,205U>
87-A40-455-080 DIODE,RL203 GW<200U>
87-A40-553-080 DIODE,1N4003 LES
87-A40-778-080 ZENER,UZ30BSD
87-A40-291-080 DIODE,1N4148 (CPT)
87-A40-764-080 ZENER,UZ10BSC
87-A40-269-080 C-DIODE,MC2836
87-A40-270-080 C-DIODE,MC2838
87-A40-749-080 ZENER,UZ5.6BSB<200LH,205U>
87-A40-748-080 ZENER,UZ5.6BSA
87-A40-739-080 ZENER,UZ2.7BSA
87-017-149-080 ZENER,HZS6A2L
MAIN C.B
C3 87-010-759-080 C-CAP,U, 0.1-25F<200LH,205U>
C4 87-010-759-080 C-CAP,U, 0.1-25F<200LH,205U>
C5 87-010-759-080 C-CAP,U, 0.1-25F<200LH,205U>
C6 87-010-759-080 C-CAP,U, 0.1-25F<200LH,205U>
C9 87-010-759-080 C-CAP,U, 0.1-25F
C10 87-010-759-080 C-CAP,U, 0.1-25F
C11 87-010-759-080 C-CAP,U, 0.1-25F
C12 87-010-759-080 C-CAP,U, 0.1-25F
C19 87-A12-431-000 CAP,E 2200-50 M 85<200LH,205U>
KANRI
NO.
REF. NO. DESCRIPTIONPART NO.
NO.
C20 87-A12-431-000 CAP,E 2200-50 M 85<200LH,205U>
C21 87-A12-442-000 CAP,E 3300-25 M 85<EXCEPT 200U>
C21 87-A12-440-000 CAP,E 3300-35 M 85 IV LELON<200U>
C22 87-A12-381-000 CAP,E 2200-25 M 85<EXCEPT 200U>
C22 87-A12-441-000 CAP,E 2200-35 M 85 IV LELON<200U>
C25 87-010-385-080 CAP, ELECT 220-25V<200LH,205U>
C25 87-010-407-080 CAP, E 33-50V<200EZ,205EZ,200U>
C26 87-010-247-080 CAP, ELECT 100-50V<200LH,205U>
C26 87-010-407-080 CAP, E 33-50V<200EZ,205EZ,200U>
C30 87-010-393-080 CAP, E 100-35V<200EZ,205EZ,200U>
C30 87-010-247-080 CAP, ELECT 100-50V<200LH,205U>
C31 87-010-263-080 CAP, ELECT 100-10V
C35 87-010-406-080 CAP, ELECT 22-50
C36 87-010-381-080 CAP, ELECT 330-16V
C38 87-010-190-080 S CHIP F 0.01
C50 87-010-393-080 CAP, E 100-35V<200EZ,205EZ,200U>
C60 87-010-403-080 CAP, ELECT 3.3-50V
C61 87-010-380-080 CAP, E 47-16V<200EZ,205EZ,200U>
C61 87-010-260-080 CAP, ELECT 47-25V<200LH,205U>
C98 87-A12-317-080 C-CAP,U 0.1-50 Z F
C123 87-012-269-080 C-CAP,U 390P-50 B<200EZ,205EZ>
C124 87-012-269-080 C-CAP,U 390P-50 B<200EZ,205EZ>
C125 87-010-759-080 C-CAP,U, 0.1-25F
C126 87-010-759-080 C-CAP,U, 0.1-25F
C127 87-010-759-080 C-CAP,U, 0.1-25F
C128 87-010-759-080 C-CAP,U, 0.1-25F
C129 87-010-191-080 C-CAP,S 0.015-50 F<200EZ,205EZ>
C130 87-010-191-080 C-CAP,S 0.015-50 F<200EZ,205EZ>
C131 87-012-286-080 CAP, U 0.01-25
C132 87-012-286-080 CAP, U 0.01-25
C133 87-A12-317-080 C-CAP,U 0.1-50 Z F
C161 87-010-408-080 CAP, ELECT 47-50V<205U>
C162 87-010-408-080 CAP, ELECT 47-50V<205U>
C181 87-010-235-080 CAP,E 470-16 SME<200EZ,205EZ>
C181 87-010-387-080 CAP,E 470-25 SME<200LH,200U,205U>
C192 87-010-759-080 C-CAP,U, 0.1-25F<200EZ,205EZ>
C401 87-A12-319-080 C-CAP,U 0.1-25 K B
C402 87-A12-319-080 C-CAP,U 0.1-25 K B
C403 87-012-193-080 C-CAP,U 82P-50 CH
C404 87-012-193-080 C-CAP,U 82P-50 CH
C405 87-012-286-080 CAP, U 0.01-25
C406 87-012-286-080 CAP, U 0.01-25
C407 87-012-286-080 CAP, U 0.01-25
C408 87-012-286-080 CAP, U 0.01-25
C409 87-012-278-080 C-CAP,U 2200P-50 B
C410 87-012-278-080 C-CAP,U 2200P-50 B
C411 87-010-405-080 CAP, ELECT 10-50V
C412 87-010-405-080 CAP, ELECT 10-50V
C421 87-012-274-080 C-CAP,U 1000P-50 K B
C422 87-012-274-080 C-CAP,U 1000P-50 K B
C423 87-012-274-080 C-CAP,U 1000P-50 K B
C424 87-012-274-080 C-CAP,U 1000P-50 K B
C425 87-010-263-080 CAP, ELECT 100-10V
C426 87-010-263-080 CAP, ELECT 100-10V
C427 87-012-188-080 C-CAP,U 47P-50 CH
C428 87-012-188-080 C-CAP,U 47P-50 CH
C429 87-010-598-080 C-CAP,S 0.068-16VRK
C430 87-010-598-080 C-CAP,S 0.068-16VRK
C431 87-012-284-080 CAP, U 6800P-50
C432 87-012-284-080 CAP, U 6800P-50
C433 87-010-546-080 CAP, ELECT 0.33-50V
C434 87-010-546-080 CAP, ELECT 0.33-50V
C435 87-010-263-080 CAP, ELECT 100-10V
C440 87-010-759-080 C-CAP,U, 0.1-25F<200EZ,205EZ>
C441 87-010-787-080 CAP, U 0.022-25
C442 87-010-759-080 C-CAP,U 0.1-25 Z F
C443 87-010-759-080 C-CAP,U, 0.1-25F
C445 87-A10-039-080 C-CAP,U 470P-50 J CH
C446 87-010-401-080 CAP, ELECT 1-50V
C447 87-010-787-080 C-CAP,U 0.022-25<EXCEPT 200U,205U>
– 6 –
Page 7
REF. NO. DESCRIPTIONPART NO. KANRI
KANRI
REF. NO. DESCRIPTIONPART NO.
NO.
C452 87-010-382-080 CAP, ELECT 22-25V
C453 87-012-279-080 C-CAP,U 2700P-50 B
C454 87-012-279-080 C-CAP,U 2700P-50 B
C455 87-012-279-080 C-CAP,U 2700P-50 B
C456 87-012-286-080 CAP, U 0.01-25
C457 87-A12-361-080 CAP,M 5600P-100 J CP
C458 87-012-274-080 CHIP CAP,U 1000P-50B<200EZ,205EZ>
C459 87-A12-468-080 C-CAP,U 560P-50 J SL<200EZ,205EZ>
C460 87-010-759-080 C-CAP,U, 0.1-25F
C461 87-A12-466-080 C-CAP,U 390P-50 J SL
C462 87-A12-466-080 C-CAP,U 390P-50 J SL
C470 87-012-270-080 C-CAP,U 470P-50 K B
C605 87-012-275-080 C-CAP,U 1200P-50 B
C606 87-012-275-080 C-CAP,U 1200P-50 B
C609 87-010-785-080 C-CAP,U 0.015-25BK
C610 87-010-785-080 C-CAP,U0.015-25BK
C611 87-010-545-080 CAP, ELECT 0.22-50V
C612 87-010-545-080 CAP, ELECT 0.22-50V
C613 87-010-545-080 CAP, ELECT 0.22-50V
C614 87-010-545-080 CAP, ELECT 0.22-50V
C615 87-012-172-080 CAPACITOR CHIP U 10P CH
C616 87-010-248-080 CAP, ELECT 220-10V
C617 87-010-248-080 CAP, ELECT 220-10V
C618 87-010-405-080 CAP, ELECT 10-50V
C625 87-010-598-080 C-CAP,S 0.068-16VRK
C626 87-010-598-080 C-CAP,S 0.068-16VRK
C630 87-016-669-080 C-CAP,S 0.1-25 K B
C677 87-012-286-080 CAP, U 0.01-25
CN102 87-A61-001-010 CONN,17P V BLK TAC-L17X-A3
CN401 87-A60-620-010 CONN,3P V 2MM JMT
CN451 87-A60-625-010 CONN,8P V 2MM JMT
CN602 87-099-194-010 CONN,6P 6216V
CNA401 86-ZM3-604-210 CONN ASSY,3P -PB
CNA451 8B-NFA-626-010 CONN,ASSY,8P -RPB
FFC602 88-906-251-110 FF-CABLE,6P 1.25
J101 87-A60-602-010 JACK,DIA6.3 BLK ST W/SW TC
J205 87-A60-545-010 JACK,PIN 4P W/R<205U>
J602 87-A60-881-010 JACK,PIN 2P MSP<EXCEPT 205U>
L101 87-A50-611-010 COIL,1UH K(CS)
L102 87-A50-611-010 COIL,1UH K(CS)
L451 87-007-342-010 COIL,OSC 85K BIAS
L451 87-007-342-010 COIL,OSC 85K BIAS
!
PT1 8B-NFA-611-010 PT,BNF-A EZ-LOW<200EZ,205EZ>
!
PT1 8B-NFA-609-010 PT,BNF-A LH<200LH>
PT1 8B-NFA-607-010 PT,BNF-A U<200U>
!
!
PT1 8B-NFA-613-010 PT,BNF-A U-HI-SUR<205U>
PT2 8B-NF9-665-010 PT,SUB BNF E (TAM)<200EZ,205EZ>
!
PT2 8B-NF9-663-010 PT,SUB BNF H (TAM)<200LH>
!
PT2 8B-NF9-661-010 PT,SUB BNF U (TAM)<200U,205U>
!
RY1 87-A91-339-010 RELAY,AC DC12V G5PA-2<200LH>
!
!
RY181 87-A92-072-010 RELAY,AC DC12V HRM3H-S-1POLE<U>
RY181 87-A91-418-010 RELAY,AC12V G5PA-1-M<200EZ,205EZ>
!
S181 87-A90-165-010 SW,SL 1-2-3 SWS2301<200LH>
!
T181 87-A60-317-010 TERMINAL, 1P MSC
!
T182 87-A60-317-010 TERMINAL, 1P MSC
!
TM101 87-A61-452-010 TERMINAL,SP 4P(MSC)
C312 87-012-195-080 C-CAP,U 100P-50CH
C501 87-010-759-080 C-CAP,U, 0.1-25F
C502 87-010-759-080 C-CAP,U, 0.1-25F
C503 87-012-278-080 C-CAP,U 2200P-50 B
C504 87-016-460-080 C-CAP,S 0.22-16 B
C505 87-010-248-040 CAP,E 220-10 SME
C507 87-010-400-040 CAP,E 0.47-50
C508 87-012-172-080 CAPACITOR CHIP U 10P CH
C509 87-A12-462-080 C-CAP,U 180P-50 J SL
C510 87-012-270-080 CAP, U 470P-50
C511 87-010-759-080 C-CAP,U, 0.1-25F
C512 87-012-268-080 C-CAP,U 330P-50 B
C513 87-010-829-080 CAP, U 0.047-16
C514 87-012-286-080 CAP, U 0.01-25
C515 87-012-274-080 CHIP CAP,U 1000P-50B
C516 87-010-759-080 C-CAP,U, 0.1-25F
C517 87-012-272-080 C-CAP,U 680P-50 B
C518 87-012-272-080 C-CAP,U 680P-50 B
C519 87-010-759-080 C-CAP,U, 0.1-25F
C520 87-010-246-040 CAP,E 47-35 SME
C521 87-A12-317-080 C-CAP,U 0.1-50 Z F
C522 87-010-263-040 CAP,E 100-10
C523 87-010-404-040 CAP,E 4.7-50 SME
C524 87-010-404-040 CAP,E 4.7-50 SME
C525 87-010-260-040 CAP,E 47-25 SME
C527 87-010-759-080 C-CAP,U, 0.1-25F
C528 87-010-759-080 C-CAP,U, 0.1-25F
CN502 87-099-196-010 CONN,8P 6216 V
CN504 87-A60-136-010 CONN,11P V FE
FFC502 88-908-201-110 FF-CABLE,8P 1.25
FFC504 88-911-131-110 FF-CABLE,11P 1.25 130MM
FL501 8B-NFA-601-010 FL,HNA-10SS19T
L501 87-A50-655-010 COIL,CLK 4.19MHZ(TOKO) 7KLY
LED501 87-A40-317-080 LED,SLR-342VCT31 RED
S201 87-A90-164-080 SW,TACT SKQAB(N)
S202 87-A90-164-080 SW,TACT SKQAB(N)
S203 87-A90-164-080 SW,TACT SKQAB(N)
S204 87-A90-164-080 SW,TACT SKQAB(N)
S205 87-A90-164-080 SW,TACT SKQAB(N)
S206 87-A90-164-080 SW,TACT SKQAB(N)
S207 87-A90-164-080 SW,TACT SKQAB(N)
S208 87-A90-164-080 SW,TACT SKQAB(N)
S209 87-A90-164-080 SW,TACT SKQAB(N)
S210 87-A90-164-080 SW,TACT SKQAB(N)<205EZ>
S211 87-A90-164-080 SW,TACT SKQAB(N)<205EZ>
S212 87-A90-164-080 SW,TACT SKQAB(N)<205EZ>
S213 87-A90-164-080 SW,TACT SKQAB(N)
S214 87-A90-164-080 SW,TACT SKQAB(N)
S215 87-A90-164-080 SW,TACT SKQAB(N)
S216 87-A90-164-080 SW,TACT SKQAB(N)
S217 87-A90-164-080 SW,TACT SKQAB(N)
S218 87-A90-164-080 SW,TACT SKQAB(N)
S219 87-A90-164-080 SW,TACT SKQAB(N)
S220 87-A90-164-080 SW,TACT SKQAB(N)
S221 87-A90-164-080 SW,TACT SKQAB(N)
S222 87-A90-164-080 SW,TACT SKQAB(N)
S223 87-A90-164-080 SW,TACT SKQAB(N)
S230 87-A92-054-010 SW,RTRY EC12E24504
FRONT C.B
C301 87-010-759-080 C-CAP,U, 0.1-25F
TUNER C.B
C303 87-012-280-080 CAP, U 3300P-50
C304 87-016-116-080 C-CAP,U 0.015-25 J B CB
C305 87-012-184-080 C-CAP,U 33P-50 CH
C306 87-012-274-080 CHIP CAP,U 1000P-50B
C771 87-010-263-080 CAP, ELECT 100-10V
C772 87-012-286-080 CAP, U 0.01-25
C779 87-010-949-080 C-CAP,S 0.01-50 BJ<200EZ,205EZ>
C780 87-010-949-080 C-CAP,S 0.01-50 BJ<200EZ,205EZ>
C307 87-012-274-080 CHIP CAP,U 1000P-50B
C782 87-012-286-080 C-CAP,U 0.01-25 K B
C308 87-010-544-040 CAP,E 0.1-50 SME
C309 87-010-404-040 CAP,E 4.7-50 SME
C310 87-012-286-080 CAP, U 0.01-25
C311 87-A12-052-080 C-CAP,S 0.033-25 J B
C783 87-012-286-080 C-CAP,U 0.01-25 K B
C784 87-012-286-080 C-CAP,U 0.01-25 K B
C785 87-012-286-080 C-CAP,U 0.01-25 K B
C786 87-012-286-080 C-CAP,U 0.01-25 K B
NO.
– 7 –
Page 8
REF. NO. DESCRIPTIONPART NO. KANRI
C788 87-012-167-080 C-CAP,U 5P-50 CH
C789 87-A12-052-080 C-CAP,S 0.033-25<200LH,200U,205U>
C789 87-016-118-080 C-CAP,U0.022-25BJ<200EZ,205EZ>
C790 87-A12-052-080 C-CAP,S 0.033-25<200LH,200U,205U>
C790 87-016-118-080 C-CAP,U0.022-25BJ<200EZ,205EZ>
C791 87-010-759-080 C-CAP,U, 0.1-25F
C792 87-012-286-080 C-CAP,U 0.01-25 K B
C793 87-010-404-080 CAP, ELECT 4.7-50V
C795 87-012-286-080 C-CAP,U 0.01-25 K B
C796 87-012-286-080 C-CAP,U 0.01-25 K B
C797 87-010-405-080 CAP, ELECT 10-50V
C798 87-012-286-080 C-CAP,U 0.01-25 K B
C799 87-010-265-080 CAP, ELECT 33-16V
C800 87-012-369-080 C-CAP,S 0.047-50F
C801 87-010-403-080 CAP, ELECT 3.3-50V
C802 87-012-369-080 C-CAP,S 0.047-50F
C803 87-010-787-080 CAP, U 0.022-25
C804 87-010-263-080 CAP, ELECT 100-10V
C807 87-010-400-080 CAP, ELECT 0.47-50V
C808 87-010-401-080 CAP, ELECT 1-50V
C809 87-010-401-080 CAP, ELECT 1-50V
C810 87-010-759-080 C-CAP,U, 0.1-25F
C814 87-012-286-080 CAP, U 0.01-25
C815 87-010-400-080 CAP, ELECT 0.47-50V
C816 87-010-400-080 CAP, ELECT 0.47-50V
C818 87-012-276-080 CAP, CHIP SS 1500 PBK<200EZ,205EZ>
C821 87-010-405-080 CAP, ELECT 10-50V
C823 87-012-349-080 C-CAP,S 1000P-50 CH<200EZ,205EZ>
C823 87-A10-978-080 C-CAP,U 820P-25<200LH,200U,205U>
C824 87-010-404-080 CAP, ELECT 4.7-50V
C825 87-010-829-080 CAP, U 0.047-16
C831 87-010-406-080 CAP, ELECT 22-50<200EZ,205EZ>
C842 87-012-286-080 C-CAP,U 0.01-25 K B
C844 87-012-286-080 C-CAP,U 0.01-25 K B
C850 87-010-260-080 CAP, ELECT 47-25V
C851 87-012-286-080 C-CAP,U 0.01-25 K B
C852 87-012-286-080 C-CAP,U 0.01-25 K B
C853 87-012-286-080 C-CAP,U 0.01-25 K B
C858 87-010-831-080 C-CAP,U 0.1-16 Z F
C859 87-010-831-080 C-CAP,U 0.1-16 Z F<200EZ,205EZ>
C860 87-012-286-080 C-CAP,U 0.01-25 K B<200EZ,205EZ>
C869 87-012-286-080 CAP, U 0.01-25<205EZ>
C870 87-012-274-080 CHIP CAP,U 1000P-50B<205EZ>
C871 87-012-199-080 CAP 220P<205EZ>
C872 87-012-199-080 CAP 220P<205EZ>
C873 87-A10-039-080 C-CAP,U 470P-50 J CH<205EZ>
C874 87-010-405-080 CAP, ELECT 10-50V<205EZ>
C875 87-010-759-080 C-CAP,U, 0.1-25F<205EZ>
C876 87-010-405-080 CAP, ELECT 10-50V<205EZ>
C877 87-012-286-080 CAP, U 0.01-25<205EZ>
C878 87-012-184-080 C-CAP,U 33P-50 CH<205EZ>
C879 87-012-180-080 C-CAP,U 22P-50 CH<205EZ>
C901 87-018-145-080 CAP,TC-U 6.8P-50<200LH,200U,205U>
C904 87-012-286-080 CAP, U 0.01-25<200LH,200U,205U>
C905 87-012-286-080 CAP, U 0.01-25<200LH,200U,205U>
C907 87-012-286-080 CAP, U 0.01-25<200LH,200U,205U>
C908 87-A10-915-080 C-CAP,U 1000P-25<200LH,200U,205U>
C909 87-012-286-080 CAP, U 0.01-25<200LH,200U,205U>
C910 87-012-174-080 C-CAP, CERA SS 12P<200LH,200U,205U>
C911 87-012-170-080 C-CAP,U 8P-50 CH<200LH,200U,205U>
C912 87-012-195-080 C-CAP,U 100P-50CH<200LH,200U,205U>
C913 87-012-286-080 CAP, U 0.01-25<200LH,200U,205U>
C914 87-012-166-080 C-CAP,U 4P-50 CH<200LH,200U,205U>
C915 87-012-174-080 C-CAP, CERA SS 12P<200LH,200U,205U>
C916 87-012-180-080 C-CAP,U 22P-50 CH<200LH,200U,205U>
C917 87-012-186-080 C-CAP,U 39P-50 CH<200LH,200U,205U>
C918 87-A10-039-080 C-CAP,U 470P-50<200LH,200U,205U>
C921 87-012-195-080 C-CAP,U 100P-50CH<200LH,200U,205U>
C922 87-012-174-080 C-CAP, CERA SS 12P<200LH,200U,205U>
C940 87-012-286-080 CAP, U 0.01-25<200EZ,205EZ>
KANRI
NO.
REF. NO. DESCRIPTIONPART NO.
NO.
C942 87-012-165-080 CAP 3P<200EZ,205EZ>
C947 87-012-286-080 CAP, U 0.01-25<200EZ,205EZ>
C948 87-A10-039-080 C-CAP,U 470P-50 J CH<200EZ,205EZ>
C952 87-012-286-080 CAP, U 0.01-25<200EZ,205EZ>
C957 87-012-174-080 C-CAP, CERA SS 12P CHJ<200EZ,205EZ>
C958 87-012-286-080 C-CAP,U 0.01-25 K B<200EZ,205EZ>
C959 87-010-831-080 C-CAP,U 0.1-16 Z F<200LH,200U,205U>
C960 87-010-831-080 C-CAP,U 0.1-16 Z F
C961 87-012-167-080 C-CAP,U 5P-50 CH<200LH,200U,205U>
C962 87-010-401-080 CAP, ELECT 1-50V<200EZ,205EZ>
C963 87-015-785-080 C-CAP,0.1-25 Z F C3216
C971 87-010-381-080 CAP, ELECT 330-16V
C972 87-010-404-080 CAP, ELECT 4.7-50V
C973 87-012-286-080 C-CAP,U 0.01-25 K B
C974 87-012-286-080 C-CAP,U 0.01-25 K B
C979 87-012-195-080 C-CAP,U 100P-50 J CH
C981 87-010-260-080 CAP, ELECT 47-25V
C982 87-010-759-080 C-CAP,U, 0.1-25F
C983 87-012-286-080 C-CAP,U 0.01-25 K B
C984 87-012-286-080 C-CAP,U 0.01-25 K B
C985 87-012-195-080 C-CAP,U 100P-50CH<200EZ,205EZ>
C987 87-012-286-080 C-CAP,U 0.01-25 K B
C989 87-012-286-080 C-CAP,U 0.01-25 K B<200EZ,205EZ>
C991 87-012-176-080 CAP 15P
C992 87-012-176-080 CAP 15P
C993 87-010-178-080 CHIP CAP 1000P
C995 87-010-178-080 CHIP CAP 1000P
C997 87-010-759-080 C-CAP,U, 0.1-25F
C998 87-010-260-080 CAP, ELECT 47-25V
C999 87-012-286-080 C-CAP,U 0.01-25 K B
CF831 87-008-423-010 CERAMIC FILTER, SFE10.7<EZ>
CF831 87-008-261-010 FILTER, SFE10.7MA5-A<EXCEPT EZ>
CF832 82-785-747-010 CF MS2 GHY R<200EZ,205EZ>
CF832 87-008-261-010 FILTER, SFE10.7MA5-A<EXCEPT EZ>
D902 87-A40-128-080 C-VARI-CAP,HVU202A<EXCEPT EZ>
D903 87-A40-128-080 C-VARI-CAP,HVU202A<EXCEPT EZ>
FFE831 A8-6ZA-199-170 6ZA-1 FEENC<200EZ,205EZ>
J831 87-A60-202-010 TERMINAL,ANT 4P MSP-154V-02<EXCEPT EZ>
J832 87-A60-403-010 TERMINAL,ANT PAL 2P HSP-312V05<EZ>
L801 87-A50-608-010 COIL,FM DET-N(TOK)
L802 87-A91-551-010 FLTR,PCFJZH-450 L(TOK)
L811 87-005-847-080 COIL,2.2UH(CECS)
L832 87-005-847-080 COIL,2.2UH(CECS)
L861 87-005-847-080 COIL,2.2UH(CECS)<205EZ>
L902 88-ZA1-602-110 COIL,FM-RF-U2 2G<200LH,200U,205U>
L903 88-ZA1-601-010 COIL,FM-RF-U1 2G<200LH,200U,205U>
L904 87-005-847-080 COIL,2.2UH(CECS)<200LH,200U,205U>
L905 88-ZA1-624-010 COIL,FM IFT 7-6.2 (COILS)<EXCEPT EZ>
L906 88-ZA1-603-010 COIL,FM-OSC-U 2G<200LH,200U,205U>
L941 87-A50-020-010 COIL,ANT LW(COI)<200EZ,205EZ>
L942 87-A50-019-010 COIL,OSC LW(COI)<200EZ,205EZ>
L951 8A-NF8-668-010 COIL,AM PACK 2(TOK)<200EZ,205EZ>
L951 8A-NF8-667-010 COIL,AM PACK 4(TOK)<200LH,200U,205U>
R790 87-012-286-080 C-CAP,U 0.01-25 K B
R991 87-012-195-080 C-CAP,U 100P-50 J CH
R993 87-012-195-080 C-CAP,U 100P-50 J CH
R995 87-012-195-080 C-CAP,U 100P-50 J CH
TC942 87-A91-774-080 TRIMMER,PLY 30P 6.8X5.4 CDYL<EZ>
X862 87-A70-307-010 VIB,XTAL 4.332MHZ CSA-309ST<205EZ>
X992 87-A70-306-010 VIB,XTAL 4.500MHZ CSA-309ST
AMP C.B
C32 87-012-286-080 CAP, U 0.01-25
C33 87-010-263-080 CAP, ELECT 100-10V<200U,205U>
C34 87-010-247-080 CAP, ELECT 100-50V<200LH,205U>
C34 87-010-380-080 CAP, ELECT 47-16V<200EZ,205EZ,200U>
C101 87-012-279-080 C-CAP,U 2700P-50 B<200LH,205U>
C101 87-012-281-080 C-CAP,U 3900P-50 B<200EZ,205EZ,200U>
C102 87-012-279-080 C-CAP,U 2700P-50 B<200LH,205U>
– 8 –
Page 9
REF. NO. DESCRIPTIONPART NO. KANRI
C102 87-012-281-080 C-CAP,U 3900P-50 B<200EZ,205EZ,200U>
C103 87-010-545-080 CAP, ELECT 0.22-50V
C104 87-010-545-080 CAP, ELECT 0.22-50V
C105 87-012-282-080 CAP, U 4700P-50<200EZ,205EZ,200U>
C105 87-012-274-080 CHIP CAP,U 1000P-50B<200LH,205U>
C106 87-012-282-080 CAP, U 4700P-50<200EZ,205EZ,200U>
C106 87-012-274-080 CHIP CAP,U 1000P-50B<200LH,205U>
C107 87-010-403-080 CAP, ELECT 3.3-50V
C108 87-010-403-080 CAP, ELECT 3.3-50V
C111 87-010-406-080 CAP, ELECT 22-50<200EZ,205EZ,200U>
C111 87-010-391-080 CAP,E 10-35 SME<200LH,205U>
C112 87-010-406-080 CAP, ELECT 22-50<200EZ,205EZ,200U>
C112 87-010-391-080 CAP,E 10-35 SME<200LH,205U>
C113 87-A10-946-080 C-CAP,S 220P-100 J CH<EXCEPT EZ>
C113 87-012-199-080 CAP 220P<200EZ,205EZ>
C114 87-A10-946-080 C-CAP,S 220P-100<200LH,200U,205U>
C114 87-012-199-080 CAP 220P<200EZ,205EZ>
C119 87-012-286-080 CAP, U 0.01-25
C120 87-012-286-080 CAP, U 0.01-25
C121 87-A12-317-080 C-CAP,U 0.1-50 Z F
C122 87-A12-317-080 C-CAP,U 0.1-50 Z F
C133 87-012-282-080 C-CAP,U, 4700P-50 K B
C140 87-012-278-080 C-CAP,U 2200P-50 B
C186 87-010-759-080 C-CAP,U, 0.1-25F<200LH,205U>
C187 87-010-405-080 CAP, ELECT 10-50V<200LH,205U>
KANRI
NO.
REF. NO. DESCRIPTIONPART NO.
NO.
C188 87-010-405-080 CAP, ELECT 10-50V<200LH,205U>
CN101 87-A61-015-010 CONN,17P H BLK TAC-L17P-A3
R129 87-A00-257-080 RES,M/F 0.15-1W J<200LH,205U>
R130 87-A00-257-080 RES,M/F 0.15-1W J<200LH,205U>
R131 87-A00-257-080 RES,M/F 0.15-1W J<200LH,205U>
R131 87-A00-258-080 RES,M/F 0.22-1W J<200U>
R132 87-A00-257-080 RES,M/F 0.15-1W J<200LH,205U>
R132 87-A00-258-080 RES,M/F 0.22-1W J<200U>
TH101 87-A91-042-080 C-THMS,100K 55001<200LH,200U,205U>
TH102 87-A91-042-080 C-THMS,100K 55001<200LH,200U,205U>
DECK C.B
CN1 87-099-753-010 CONN,11P H 9604
SFR1 87-024-581-010 SFR,3.3K DIA6V K0A
SOL1 82-ZM1-618-410 SOL ASSY,27
SOL2 82-ZM1-618-410 SOL ASSY,27
SW1 87-A90-673-010 SW,MICRO ESE11SH1C
SW2 87-A91-500-010 SW,MICRO MPU11470MLB0
SW3 87-A91-500-010 SW,MICRO MPU11470MLB0
SW4 87-A91-500-010 SW,MICRO MPU11470MLB0
SW5 87-A90-673-010 SW,MICRO ESE11SH1C
W1 82-ZM3-601-010 RBN-CORD,4P-75
CHIP RESISTOR PART CODE
Chip Resistor Part Coding
88
A
Resistor Code
Chip resistor
Wattage Type Tolerance
1/16W 1005 5% CJ
1/16W
1/10W
1/8W
1608
2125
3216
5%
5%
5%
Symbol
CJ
CJ
CJ
Figure
Value of resistor
Form
L
Dimensions (mm)
t
W
0.55
Resistor Code
108
118
128
LW t
1.0 0.5 0.35 104
1.6 0.8 0.45
2 1.25 0.45
3.2
1.6
: A
: A
– 9 –
Page 10
TRANSISTOR ILLUSTRATION
E C B
2SA1980G
CDA1585BC
CSC4115BC
KTC3198GR
2SK2937
B C E
2SA1981Y
2SC5343G
E C BG D S
2SJ460
2SK2541
2SB1342
2SB1370
2SB1677
2SB1686
B
2SA1235F
2SC2714O
2SC3052F
CMBT5551
CMBT5401
B C E
2SD1933
2SD2619
2SD2642
C
E
CSD1306E
KRA102S
KRA107S
KRC102S-RTK
KRC104S
E C B
CC5551
G
S
2SK360E
D
– 10 –
Page 11
WIRING 1 (MAIN / FRONT / TUNER)<EZ>
32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 1 1 10 9 8 7 6 5 4 3 2 1
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
11
R
S
T
U
Page 12
SCHEMATIC DIAGRAM – 1 (MAIN 1/2)<EZ>
– 12 –
Page 13
SCHEMATIC DIAGRAM – 2 (FRONT / DECK)<EZ>
– 13 –
Page 14
SCHEMATIC DIAGRAM – 3 (TUNER)<EZ>
– 14 –
Page 15
SCHEMATIC DIAGRAM – 4 (MAIN 2/2: PT SECTION)<EZ>
– 15 –
Page 16
WIRING 2 (MAIN / FRONT / TUNER)<U,LH>
32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 1 1 10 9 8 7 6 5 4 3 2 1
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
16
R
S
T
U
Page 17
SCHEMATIC DIAGRAM – 5 (MAIN 1/2)<U,LH>
– 17 –
Page 18
SCHEMATIC DIAGRAM – 6 (FRONT / DECK)<U,LH>
– 18 –
Page 19
SCHEMATIC DIAGRAM – 7 (TUNER)<U,LH>
– 19 –
Page 20
SCHEMATIC DIAGRAM – 8 (MAIN 2/2: PT SECTION)<200U>
– 20 –
Page 21
SCHEMATIC DIAGRAM – 9 (MAIN 2/2: PT SECTION)<205U>
– 21 –
Page 22
SCHEMATIC DIAGRAM - 10 (MAIN 2/2: PT SECTION)<200LH>
– 22 –
Page 23
WIRING 3 (AMP)<EZ>
32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 1 1 10 9 8 7 6 5 4 3 2 1
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
23
R
S
T
U
Page 24
SCHEMATIC DIAGRAM – 11 (AMP)<EZ>
– 24 –
Page 25
WIRING 4 (AMP)<200U>
32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 1 1 10 9 8 7 6 5 4 3 2 1
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
25
R
S
T
U
Page 26
SCHEMATIC DIAGRAM – 12 (AMP)<200U>
– 26 –
Page 27
WIRING 5 (AMP)<205U,200LH>
32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 1 1 10 9 8 7 6 5 4 3 2 1
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
27
R
S
T
U
Page 28
SCHEMATIC DIAGRAM – 13 (AMP)<200LH,205U>
– 28 –
Page 29
WIRING 6 (DECK)
32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
E DECK C.B
SW5
(CAM2)
IC2
1
3
SW4
(CST2)
TO FRONT C.B CN504
1 3 5 7 9 11
2 4 6 8 10
CN1
SFR1
SOL2
R1
(FFC504)
SW3
(REA)
A
B
SW2
+
H
L
IC1
1
3
(CST1)
SOL1
SW1
(CAM1)
W1
+
H
M1
TAPE
MOTOR
C
D
E
F
G
H
I
L
J
K
L
M
N
O
P
Q
R
S
29
T
U
Page 30
IC BLOCK DIAGRAM
– 30 –
Page 31
FL (HNA-10SS19T) GRID ASSIGNMENT AND ANODE CONNECTION
GRID ASSIGNMENT
– 31 –
Page 32
ANODE CONNECTION / PIN CONNECTON
– 32 –
Page 33
IC DESCRIPTION
IC, UPD780226GF-022-3BA<EXCEPT 205EZ> / UPD780228GF-079-3BA<205EZ>
Pin No. Pin Name I/O Description
1 SOL1 O DECK1 solenoid output.
2 SOL2 O DECK2 solenoid output.
3 O-MOTOR O DECK MOTOR ON/OFF output.
4 O-PB2 O DECK2/DECK1 play output.
5 O-BIAS O BIAS ON output.
6 O-RMT O REC mute output.
7 O-CD. ON O CD ON output.
8 O-TU. ON O TUNER ON output.
9 NC - Not connected.
10 O-STBY. LED O STANDBY LED ON/OFF output.
11 O-CLK SFT O Micon clock shift output.
12 ~ 16 NC - Not connected.
17 IC - Internal connection (connected to GND).
18 VSS0 - GND.
19 VDD0 - Power supply.
20 I-VOL A I Volume rotary encoder input A.
21 I-VOL B I Volume rotary encoder input B.
22 O-POWER O System power supply ON/OFF output.
23 O-DISH-R O CD turntable reverse rotation output.
24 CD. CE/O-CD DATA O CD enable output / CD data output.
25 I-TUNE/IFC I Tuner SD detection input / Tuner IF count input.
26
27 I-WRQ I CD WRQ input.
28 I-RDS. CLK I Tuner RDS clock input (UPD780228GF-079-3BA only).
29 I-SUB. Q I SUB Q data input.
30 RESET - System reset.
31 O-DSC DATA O Function IC control output.
32 I-STEREO I Tuner stereo input.
33 I-DRF I CD DRF input.
34 I-RMC I System remote control input.
35 I-TM. BASE I Base input for clock.
36 I-DISH I CD turntable photo sensor A/D input.
I-RDS. DATA
I/O
/O-STB. ECHO / Strobe output for shift register.
Tuner RDS data input (UPD780228GF-079-3BA only).
37 VDD1 - Power supply.
38 X2 - 4.19 MHz oscillator circuit.
39 X1 - 4.19 MHz oscillator circuit.
40 VSS1 - GND.
41 AVDD - Power supply.
42 I-HOLD I Power failure detected input.
43 I-CD SW I CD mecha switch input.
44 I-SPEANA1 I A/D 1 input for spectrum analyser level display.
– 33 –
Page 34
Pin No. Pin Name I/O Description
45 I-SPEANA2 I A/D 2 input for spectrum analyser level display.
46 I-SPEANA3 I A/D 3 input for spectrum analyser level display.
47 I-KEY1 I Key 1 input.
48 I-KEY2 I Key 2 input.
49 I-TU. SIG I Tuner tuning signal level input (UPD780228GF-079-3BA only).
50 AVSS - GND.
51 O-PLL CLK O PLL clock enable output.
52 O-PLL CE O Chip enable output for tuner PLL.
53 O-CD CLK O CD clock output.
54 O-CD DATA O CD data output.
55 O-CLOSE O CD tray close data output (Not used).
56 O-OPEN O CD tray open data output (Not used)s.
57 O-DISH F O CD turntable forward rotation output (Not used).
58 O-KSCAN O Key scan output.
59 CST1 I DECK 1 cassette detect switch data input.
60 REA I DECK 2 side-A recordable switch data input. “L” = REC.
61 CAM1 I DECK 1 CAM STOP switch data input.
62 AUTO2 I DECK 2 AUTO STOP switch data input.
63 AUTO1 I DECK 1 AUTO STOP switch data input.
64 CAM2 I DECK 2 CAM switch data input.
65 REB I DECK 2 side-B recordable switch data input. “L” = REC.
66 CST2 I DECK 2 cassette detect switch data input.
67 P1/I-AM-10K I/O FL segment P1 output / AM10K data input (U,LH only).
68 P2/I-AM. ST I/O FL segment P2 output / AM ST data input (Not used).
69 P3/I-LW I/O FL segment P3 output / LW mode data input (EZ only).
70 P4/I-SW I/O FL segment P4 output / SW mode data input (Not used).
71 P5/I-OIRT I/O FL segment P5 output / OIRT data input (Not used).
72 P6/I-RDS I/O FL segment P6 output / RDS data input (UPD780228GF-079-3BA only).
73 P7/I-R+1 I/O FL segment P7 output / REV data input (Not used).
74 P8/I-DEMO I/O FL segment P8 output / DEMO data input (Not used).
75 P9/I-C-JACK I/O FL segment P9 output / C-JACK data input (LH only).
76 P10/I-ECO-OFF I/O FL segment P10 output / ECO-OFF data input (LH only).
77 P11/I-FM WIDE I/O FL segment P11 output / FM WIDE data input (Not used).
78 P12 O FL segment P12 output.
79 VDD2 - Power supply.
80 VLOAD - Power supply for FL display.
81 ~ 90 P13 ~ P22 O FL segment P13 ~ P22 output.
91 ~ 100 G1 ~ G10 O FL grid G1 ~ G10 output.
– 34 –
Page 35
ADJUSTMENT – 1 <TUNER / FRONT>
< TUNER SECTION >
1. Clock Frequency Check
Settings : • Test point : TP2 (CLK)
Method : U,LH: Set to AM 1710 kHz and check that the test point
is 2160 kHz ± 45 Hz.
EZ: Set to MW 1602 kHz and check that the test point
is 2052 kHz ± 45 Hz.
2. AM VT Check<U,LH>
Settings : • Test point : TP1 (VT)
Method : Set to AM 1710 kHz and check that the test point is less
than 8.0 V. Then set to AM 530 kHz and check that the
test point is more than 0.6 V.
3. MW VT Check<EZ>
Settings : • Test point : TP1 (VT)
Method : Set to MW 1602 kHz and check that the test point is less
than 8.0 V. Then set to MW 531 kHz and check that the
test point is more than 0.6 V.
4. LW VT Adjustment<EZ>
Settings : • Test point : TP1 (VT)
• Adjustment location : L942
Method : Set to LW 144 kHz and adjust L942 so that the test point
becomes 1.3 V ± 0.05 V. Then set to LW 290 kHz and
check that the test point is less than 8.0 V.
5. AM Tracking Adjustment<U,LH>
Settings : • Test point : TP8 (Lch), TP9 (Rch)
• Adjustment location : L951(1/3)
Method : Set to AM 1000 kHz and adjust L951(1/3) so that the
test point becomes maximum.
6. MW Tracking Adjustment<EZ>
Settings : • Test point : TP8 (Lch), TP9 (Rch)
• Adjustment location : L951(1/3)
Method : Set to MW 999 kHz and adjust L951(1/3) so that the test
point becomes maximum.
7. LW Tracking Adjustment<EZ>
Settings : • Test point : TP8 (Lch), TP9 (Rch)
• Adjustment location :
L941 ................................................... 144 kHz
TC942 ................................................. 290 kHz
Method : Set up TC942 to center before adjustment.
The level at 144 kHz is adjusted to maximum by L941.
Then the level at 290 kHz is adjusted to maximum by
TC942.
8. AM IF Adjustment
Settings : • Test point : TP8 (Lch), TP9 (Rch)
• Adjustment location :
L802 ................................................... 450 kHz
9. FM VT Check<U,LH>
Settings : • Test point : TP1 (VT)
Method : Set to FM 87.5 MHz check that the test point is more
than 0.5 V. Then set to FM 108.0 MHz and check that
the test point is 7.0 V ± 0.1 V.
11. FM Tracking adjust<U,LH>
Settings : • Test point : TP8 (Lch), TP9 (Rch)
• Adjustment location: L903
Method : Set to FM 87.5 MHz and adjust L903 so that the
test point is less than 9 dBµV.
12. FM Tracking check<EZ>
Settings : • Test point : TP8 (Lch), TP9 (Rch)
Method : Set to FM 98.0 MHz and check that the test point
is less than 13 dBµV.
13. DC Balance / Mono Distortion Adjustment
Settings : • Test point : TP3, TP4 (DC)
TP8 (LCH), TP9 (RCH)
(MONO DISTORTION)
• Adjustment location : L801
• Input level : 60 dBµV
Method : Set to FM 98.0 MHz and adjust L801 so that the
voltage between TP3 and TP4 becomes 0 V ± 500 mV
with minimum distortion.
14. Output Level Check
<AM/MW>
Settings : • Test point : TP8 (Lch), TP9 (Rch)
• Input level : 74 dBµV
Method : Set to AM1000 kHz , MW 999 kHz and check that the
test point is 50 mV ± 3 dB.
<FM>
Settings : • Test point : TP8 (Lch), TP9 (Rch)
• Input level : 60 dBµV
Method : Set to FM 98.0MHz and check that the test point is
150 mV ± 3 dB.
15. FM Separation Check
Settings : • Test point : TP8 (Lch), TP9 (Rch)
• Input level : 60 dBµV
Method : U,LH: Set to FM 98.0 MHz and check that the test
point is more than 25 dB.
EZ: Set to FM 83.0 MHz and check that the test point
is more than 12 dB.
< FRONT SECTION >
16. µ-CON OSC Adjustment
Settings : • Test point : TP5 (KEY-SCAN)
TP6 (GND)
• Adjustment location : L501
Method : Insert AC plug while pressing of "POWER" key and
"TUNER" function key.
Connect a frequency counter across TP5 and TP6.
Then adjust L501 so that the test point becomes
92.470 Hz ± 0.092 Hz.
[ Manual Reset ]
Make up for RESET after adjustment.
* Reset is to press "POWER" key while pressing of
"CLEAR (STOP)" key.
10. FM VT Check<EZ>
Settings : • Test point : TP1 (VT)
Method : Set to FM 87.5 MHz check that the test point is more
than 0.5 V. Then set to FM 108.0 MHz and check that
the test point is less than 8.0 V.
– 35 –
Page 36
ADJUSTMENT – 2 <DECK>
< DECK SECTION >
1. Tape Speed Adjustment (DECK 2)
Settings : • Test tape : TTA–100
• Test point : TP8 (Lch), TP9 (Rch)
• Adjustment location : SFR1
Method : Play back the test tape and adjust SFR1 so that the
test point becomes 3000 Hz ± 5 Hz (FWD) and FWD
SPEED ± 45Hz (REV) with respect to forward speed.
2. Head Azimuth Adjustment (DECK 1, DECK 2)
Settings : • Test tape : TTA–330
• Test point : TP8 (Lch), TP9 (Rch)
• Adjustment location : Head azimuth
adjustment screw
Method : Play back (FWD) the 8 kHz signal of the test tape and
adjust screw so that the output becomes maximum.
Next, perform on REV PLAY mode.
3. PB Frequency Response Check (DECK 1, DECK 2)
Settings : • Test tape : TTA–330
• Test point : TP8 (Lch), TP9 (Rch)
Method : Play back the 315 Hz and 10 kHzsignals of the test
tape and check that the output ratio of the 10 kHz
signal with respect to that of the 315 Hz signal is
0 dB ± 3 dB.
4. REC/PB Frequency Response Check (DECK 2)
Settings : • Test tape : TTA–602
• Test point : TP8 (Lch), TP9 (Rch)
• Input signal : 8 kHz/1 kHz (-20 VU / 0dB)
Method : Apply a 1 kHz signal and REC mode. Then adjust
OSC attenuator so that the output level at TP8, TP9
becomes 10 mV. Record and play back
the 1 kHz signals and check that the output is
0 dB ± 5 dB.
5. REC/PB Sensitivity Check (DECK 2)
Settings : • Test tape : TTA–602
• Test point : TP8 (Lch), TP9 (Rch)
• Input signal : 8 kHz (0VU / 0 dB)
Method : Apply a 1 kHz signal and REC mode. Then adjust
OSC attenuator so that the output level at TP8, TP9
becomes 100 mV. Record and play back
the 1 kHz signals and check that the output is
–1 dB ± 3.5 dB.
4. PB Sensitivity Check (DECK 1, DECK 2)
Settings : • Test tape : TTA–200
• Test point : TP8 (Lch), TP9 (Rch)
Method : Play back the test tape and check that the output level
of the test point is 110 mV ± 3 dB.
– 36 –
Page 37
CD TEST MODE
1. How to Start the CD Test Mode
While pressing the FUNCTION button, insert the AC plug to the power outlet.
When the test mode is started, the message [CD TEST] is displayed.
2. How to Exit the CD Test Mode
Press the POWER button or disconnect the AC plug.
*When any key other than PLAY is pressed during play mode, the machine exits the test mode.
3. Function Descriptions and Application of the CD Test Mode
No
1
2
3
4
5
6
Mode
Start mode
Search
mode
Play mode
Traverse
mode
Sled mode
Spindle
mode
Operation
STOP button
Play button
PAUSE
button
FF button
RWD button
REC/REC
MUTE button
Display
All indicators light
READING
Normal
Normal
CD TEST
CD TEST
All indicators light
Function
• All FL indicators light
• LD illuminates all the time
• Focus search continuous
operations *1
• Spindle motor continuous kick
• Normal playback
• If TOC cannot be read, focus
search is continued
• Tracking servo OFF/ON
• Each time PAUSE button is
pressed, the tracking servo
repeats turning OFF/ON
• Pickup moves to the inner
circumference *2
At the same time, lens kicks to
the inner circumference
• Pickup moves to the outer
circumference *2
At the same time, lens kicks to
the outer circumference
• The spindle motor rotates
forward (rough speed) by
pressing the button and rotates
backward by pressing one more
time and stops by pressing again
Checking item
• FL check
• Microprocessor check
• APC circuit check
• Laser current measurement
• Focus search waveform check
• Focus error waveform check
(DRF in the search mode is
ignored)
• Each servo circuit is checked
• DRF check
• Tracking balance check
• Sled circuit check
• Tracking circuit check
• Mechanism operation check
• Pickup check
• Spindle circuit
• Spindle motor
*1: The driver IC heats up and the protection circuit starts working when the focus search is continued for 10 minutes or longer. There can be a
case that operations can not be performed correctly.
In such a case, turn off the main power. After cooling down the machine, restart the machine.
*2: Be careful not to damage the gear because the sled motor rotates while the FF or RWD button is being pressed even if the pick-up is located
in the innermost track or the outermost track.
– 37 –
Page 38
MECHANICAL EXPLODED VIEW 1 / 1
A
A
A
10
11
FFC602
BZG-2
14
a
13
E
12
8
A
9
15
22
24
17
18
FL
16
A
A
19
a
HLDR, WIRE
200U, 200EZ, 205EZ
A
25
d
26
PT001
FFC502
B
F
PWB
FFC504
c
A
33
C
A
b
c
d
PWB
A
A
A
32
A
34
A
A
29
30
F
31
A
E
b
7
12
6
4
5
3
2
1
A
CUSH, 11-8.5-2
11
20
A
ZZM-3
8
21
A
D
200LH, 205U
c
27
28
CABI, BOTTOM
A
A
PWB
A
A
A
A
23
A
HT-SINK
A
HT-SINK, FIN
– 38 –
Page 39
MECHANICAL PARTS LIST 1 / 1
REF. NO. DESCRIPTIONPART NO. KANRI
1 8A-NF8-282-010 SPR-T,EJECT 2
2 8B-NFA-003-010 BOX,CASS 2
3 8B-NFA-010-010 WINDOW,CASS 2
4 8B-NFA-009-010 WINDOW,CASS 1
5 8A-NF8-281-010 SPR-T,EJECT 1
6 8B-NFA-002-010 BOX,CASS 1
7 8B-NFA-024-010 WINDOW,DISP H<200LH,200EZ>
7 8B-NFA-032-010 WINDOW,DISP HI205 U<205U>
7 8B-NFA-023-010 WINDOW,DISP REZ<205EZ>
7 8B-NFA-008-010 WINDOW,DISP U<200U>
8 8Z-NF6-210-010 DMPR,150 N
9 87-B00-002-010 BADGE,AIWA 30 ABS SIL
10 87-NF4-216-010 HLDR,LOCK 1
11 86-NF9-224-010 SPR-C,LOCK
12 82-NF5-229-010 PLATE,LOCK
13 8B-NFA-026-010 CABI,FR REZ<205EZ>
13 8B-NFA-001-010 CABI,FR U<EXCEPT 205EZ>
14 8B-NFA-015-010 KEY,POWER
15 8B-NFA-017-010 KEY,FUN
16 8B-NFA-011-010 RING,OPE
17 8B-NFA-018-010 KEY,OPE
18 8B-NFA-016-010 KEY,GEQ
19 8B-NFA-020-010 KEY,REC
20 87-NF4-217-110 HLDR,LOCK 2
21 8A-NFA-011-110 KNOB,RTRY VOL
22 8B-NFA-019-010 KEY,RDS<205EZ>
23 8B-NFA-222-010 HLDR,HT-SINK
24 8B-NFA-007-010 PANEL,TRAY
25 8B-NFA-004-010 PANEL,TOP
26 82-NF7-210-110 GUIDE,FL (*)
KANRI
NO.
REF. NO. DESCRIPTIONPART NO.
27 8B-NFA-206-010 HLDR,PT T1 66-55/50<200LH,205U>
28 8B-NFA-204-010 HLDR,PT S 57-35 /66-30/25<EZ>
28 8B-NFA-202-010 HLDR,PT S 57-40<200U>
29 8B-NFA-218-010 HLDR,TR SUS
30 8B-NFA-203-010 HLDR,AMP
31 8B-NFA-006-010 PANEL,RIGHT
32 8B-NFA-054-010 CABI,REAR EZSC<200EZ>
32 8B-NFA-061-010 CABI,REAR HI205 USC<205U>
32 8B-NFA-052-010 CABI,REAR LHSC<200LH>
32 8B-NFA-058-010 CABI,REAR REZSC<205EZ>
32 8B-NFA-051-010 CABI,REAR USC<200U>
33 8B-NFA-005-010 PANEL,LEFT
!
34 87-A80-157-010 AC CORD ASSY,E BLK CC<200EZ,205EZ>
!
34 87-A80-092-010 AC CORD ASSY,E BLK SUN FAI<200LH>
!
34 87-A80-110-010 AC CORD ASSY,U SPT-2W<200U,205U>
A 87-067-703-010 TAPPING SCREW, BVT2+3-10
B 87-067-975-010 S-SCREW,IT+4-8
C 87-NF4-224-010 S-SCREW,IT3B+3-8 CU
D 87-067-584-010 SCREW, BVT2+3-6<EXCEPT EZ,200U>
E 87-721-096-410 QT2+3-10 GLD
F 87-067-641-010 UTT2+3-8(W/O SLOT)BL
NO.
COLOR NAME TABLE
Basic color symbol Color Basic color symbol Color Basic color symbol Color
B Black C Cream D Orange
G Green H Gray L Blue
LT Transparent Blue N Gold P Pink
R Red S Silver ST Titan Silver
T Brown V Violet W White
WT Transparent White Y Yellow YT Transparent Yellow
LM Metallic Blue LL Light Blue GT Transparent Green
LD Dark Blue DT Transparent Orange GM Metallic Green
YM Metallic Yellow DM Metallic Orange PT Transparent Pink
LA Aqua Blue GL Light Green HT Transparent Gray
– 39 –
Page 40
TAPE MECHANISM EXPLODED VIEW 1 / 1
TERMINAL,
LB1
33
31
AA
34
32
30
21
20
19
55
35
28
27
26
25
24
29
37
39
38
36
41
40
43
42
44
52
33
31
21
20
50
52
51
43
42
40
b
45
46
47
a
a
48
49
B
41
44
45
46
51
b
53
47
48
49
A
TERMINAL,LB1
32
35
30
29
28
27
26
25
23
18
22
5
6
14
10
11
15
7
16
9
1
2
6
10
11
8
5
3
c
14
9
17
16
19
IC, EW732
18
54
38
39
37
PWB
12
24
23
22
IC, EW732
54
c
12
13
4
– 40 –
15
13
Page 41
TAPE MECHANISM PARTS LIST 1 / 1
REF. NO. DESCRIPTIONPART NO. KANRI
1 8Z-ZM3-227-010 BELT,MAIN M3
2 8Z-ZM3-235-010 BELT,MAIN L
3 8Z-ZM1-235-010 PULLEY,MOT
4 87-045-347-010 MOT,SHU2L 70
5 8Z-ZM1-232-010 GEAR,IDL FF/REW
6 8Z-ZM3-244-010 GEAR,CAM TD20
7 8Z-ZM3-256-010 FLY-WHL ASSY,M3 R
8 8Z-ZM3-255-010 FLY-WHL ASSY,M3 L
9 8Z-ZM3-231-010 SPR-T,TRIG
10 8Z-ZM3-213-010 CLR,MG
11 82-ZM3-616-010 RING MAGNET 4
12 8Z-ZM3-243-010 LEVER ASSY,HD UP
13 8Z-ZM3-238-010 SPR-T,HD UP
14 8Z-ZM3-219-010 GEAR,CAM M3
15 8Z-ZM3-206-010 LEVER,TRIG
16 8Z-ZM3-209-010 LEVER,CAM FR
17 8Z-ZM3-203-010 CHAS ASSY,M3
18 8Z-ZM1-228-010 GEAR,SLIP T-UP B
19 8Z-ZM1-265-010 FELT,T-UP
20 8Z-ZM1-227-010 GEAR,SLIP T-UP A
21 8Z-ZM1-251-110 SPR-C,T-UP SLIP
22 8Z-ZM1-275-010 W-L,1,47-4-0.25
23 8Z-ZM1-257-010 SPR-C,F/R
24 8Z-ZM1-236-010 CLR,SLIP FF/REW
25 8Z-ZM3-226-010 SPR-C,FR M3
26 8Z-ZM3-250-010 GEAR,SLIP F/R A M3
27 8Z-ZM1-269-010 FELT,FF/REW 2
28 8Z-ZM1-238-110 GEAR,SLIP FF/REW B 2
29 8Z-ZM3-220-010 LEVER,FR M3
30 8Z-ZM3-205-010 LEVER,PLAY M3
KANRI
NO.
REF. NO. DESCRIPTIONPART NO.
NO.
31 8Z-ZM3-233-010 SPR-T,BRG M3
32 84-ZM2-227-310 SPR-C,AZIMUTH
33 87-A90-403-110 HEAD,RPH MS15R
34 87-A90-404-010 HEAD,EH LE15B
35 8Z-ZM3-239-010 SPR-E,FR
36 8Z-ZM3-211-010 LEVER,EJECT R
37 8Z-ZM3-225-010 LEVER,STOP
38 8Z-ZM3-221-010 LEVER,CAS
39 8Z-ZM3-234-010 SPR-T,LVR CAS
40 8Z-ZM3-223-010 SPR-C,REEL R M3
41 8Z-ZM1-225-110 GEAR,REEL R
42 8Z-ZM3-240-010 SPR-T,T-UP M3
43 8Z-ZM3-237-010 SPR-T,PINCH M3
44 8Z-ZM3-215-010 LEVER,PINCH M3
45 8Z-ZM1-261-110 ROLLER ASSY,PINCH
46 8Z-ZM1-226-010 GEAR,REEL L
47 8Z-ZM3-222-010 SPR-C,REEL L M3
48 8Z-ZM3-251-010 GEAR,IDL REW M3
49 8Z-ZM3-236-010 SPR-T,PLAY M3
50 82-ZM1-240-110 LVR,REC(*)
51 8Z-ZM3-216-010 LEVER,T-UP M3
52 87-B10-301-010 W-L,1.63-3.2-05 SLIT
53 8Z-ZM3-212-010 LEVER,EJECT L
54 8Z-ZM3-214-010 HLDR,IC
55 8B-NFA-626-010 CONN ASSY,8P -RPB
A 84-ZM2-242-010 S-SCREW,AZ1-2-6.4
B 8Z-ZM2-220-110 V+2.6 ZZM-2
– 41 –
Page 42
GENERAL SPEAKER DISASSEMBLY INSTRUCTIONS (FOR REFERENCE)
Type.1
Insert a flat-bladed screwdriver into the position indicated by the
arrows and remove the panel. Remove the screws of each speaker
unit and then remove the speaker units.
Type.2
Remove the grill frame and four pieces of rubber caps by pulling
out with a flat-bladed screwdriver. Remove the screws from hole
where installed rubber caps. Insert a flat-bladed screwdriver into
the position indicated by the arrows and remove the panel. Remove the screws of each speaker unit and then remove the speaker
units.
Type.4
TOOLS
1 Plastic head hammer
2 (() flat head screwdriver
3 Cut chisel
12 3
How to Remove the PANEL, FR
1. Insert the (() flat head screwdriver tip into the gap
between the PANEL, FR and the PANEL, SPKR. Tap the
head of the (() flat head screwdriver with the plastic
hammer head, and create the clearance as shown in Fig-1.
2. Insert the cut chisel in the clearance, and tap the head of
the cut chisel with plastic hammer as shown in Fig-2, to
remove the PANEL, FR.
Type.3
Insert a flat-bladed screwdriver into the position indicated by the
arrows and remove the panel. Turn the speaker unit to counterclockwise direction while inserting a flat-bladed screwdriver into
one of the hollows around speaker unit, and then remove the speaker
unit. After replacing the speaker unit, install it turning to clockwise
direction until "click" sound comes out.
3. Place the speaker horizontally. Tap head of the cut chisel
with plastic hammer as shown in Fig-3, and remove the
PANEL, FR completely.
Fig-1 Fig-2
How to Attach the PANEL, FR
Attach the PANEL, FR to the PANEL, SPKR. Tap the four
corners of the PANEL, FR with the plastic hammer to fit the
PANEL, FR into the PANEL, SPKR completely.
– 42 –
Fig-3
Page 43
SPEAKER PARTS LIST
(SX-NAJ202<YUSN> / NSZ202<YSC> / NSZ205<YSC, YLSC> / NAJ205<YUSN>)
REF. NO. DESCRIPTIONPART NO. KANRI
1 8B-NSL-001-010 PANER,FR
2 8B-NSL-006-010 GRILLE,FRAME ASSY<NSZ205YLSC,SNAJ205YUSN>
2 8B-NSL-020-010 GRILLE,FRAME ASSY 2WAY<NSZ202YSC,SNAJ202YUSN,NSZ205YSC>
3 8A-NSL-603-010 SPKR, CERAMIC
4 8B-NSL-019-010 SPKR, CERAMIC ASSY
5 8B-NSL-602-010 SPKR, W 120/25<NSZ205YLSC,SNAJ205YUSN>
5 8B-NSL-608-010 SPKR, W 120/16<NSZ205YSC,SNAJ202YUSN,NSZ202YSC>
6 8B-NSL-604-010 SPKR, TW 50<NSZ205YLSC,SNAJ205YUSN>
KANRI
NO.
REF. NO. DESCRIPTIONPART NO.
NO.
SPEAKER PARTS LIST (SX-R145<YUSN>)
REF. NO. DESCRIPTIONPART NO.
1 81-VSA-010-010 SPKR, CORD
2 87-010-384-010 CAP,E 100-25 M SME
3 8A-YS4-610-010 CORD,SPKR 3.5
4 8A-YS4-601-010 SPKR,80
5 8A-YS4-006-010 GRILLE, FRAME ASSY
KANRI
NO.
ACCESSORIES / PACKAGE LIST
REF. NO. DESCRIPTIONPART NO.
1 8B-NFA-902-010 IB,LH(ESP)S<200LH>
1 8B-NFA-903-010 IB,U(ESF)S<U>
1 8B-NFA-906-010 IB,EZ(9L)S-RDS(205)<205EZ>
1 8B-NFA-916-010 IB,EZ(9L)S<200EZ>
2 87-043-115-010 FEEDER-ANT,FM<U,LH>
3 87-A90-118-010 ANT,WIRE FM(Z)<EZ>
4 87-A92-150-010 ANT,LOOP AM NO-CONT
!
5 87-A91-017-010 PLUG,CONVERSION JT-0476<LH>
6 8B-NFC-702-010 RC UNIT,RC-AAS11(VS)
KANRI
NO.
– 43 –
Page 44
2–11, IKENOHATA 1–CHOME, TAITO-KU, TOKYO 110, JAPAN TEL:03 (3827) 3111
Printed in Singapore9820572 0251431
Loading...