Aiwa CSDTD-61, CSDTD-63 Service manual

CSD-TD63

LHS HAS

CSD-TD61

EZS

SERVICE MANUAL

COMPACT DISC STEREO RADIO

CASSETTE RECORDER

BASIC TAPE MECHANISM : TN-21ZVC-2000
BASIC CD MECHANISM : DA11T3C

S/M Code No. 09-003-343-9N1

DATA

SPECIFICATIONS

EZ MODEL

Design and specifications are subject to change without

•

notice

.

LH/HA MODELS

Design and specifications are subject to change without

•

notice

.

ACCESSORIES/PACKAGE LIST

REF. NO PART NO. KANRI DESCRIPTION

1 8A-CH9-906-010 IB,EZ(9L)B<1EZ>
1 8A-CHK-902-010 IB,LH(ESP)B<3LH,3HA>

!

2 87-A80-119-010 AC CORD SET ASSY,AZ<3HA>

!

2 87-A80-036-010 AC CORD SET ASSY,E W/FLTR VOL

!

3 87-A90-312-010 PLUG,CONVERSION WTN-1157R1<3LH>

4 8Z-CK4-962-010 RC UNIT,RC-ZAT04 (VS)

NO.

<3LH,1EZ>

2

PROTECTION OF EYES FROM LASER BEAM DURING SERVICING

CLASS 1
KLASSE 1
LUOKAN 1
KLASS 1

LASER PRODUCT
LASER PRODUKT
LASER LAITE
LASER APPARAT

This set employs laser. Therefore, be sure to follow carefully the
instructions below when servicing.

WARNING!

WHEN SERVICING, DO NOT APPROACH THE LASER EXIT
WITH THE EYE TOO CLOSELY. IN CASE IT IS NECESSARY TO
CONFIRM LASER BEAM EMISSION. BE SURE TO OBSERVE
FROM A DISTANCE OF MORE THAN 30cm FROM THE
SURFACE OF THE OBJECTIVE LENS ON THE OPTICAL
PICK-UP BLOCK.

Caution: Invisible laser radiation when
open and interlocks defeated avoid expo­sure to beam.
Advarsel:Usynling laserståling ved åbning,
når sikkerhedsafbrydere er ude af funktion.
Undgå udsættelse for stråling.

VAROITUS!

Laiteen Käyttäminen muulla kuin tässä käyttöohjeessa mainit­ulla tavalla saattaa altistaa käyt-täjän turvallisuusluokan 1 ylit­tävälle näkymättömälle lasersäteilylle.

CAUTION

Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous
radiation exposure.

ATTENTION

L'utilisation de commandes, réglages ou procédures autres que
ceux spécifiés peut entraîner une dangereuse exposition aux
radiations.

ADVARSEL!

Usynlig laserståling ved åbning, når sikkerhedsafbrydereer ude
af funktion. Undgå udsættelse for stråling.

This Compact Disc player is classified as a CLASS 1 LASER
product.
The CLASS 1 LASER PRODUCT label is located on the rear
exterior.

VARNING!

Om apparaten används på annat sätt än vad som specificeras i
denna bruksanvising, kan användaren utsättas för osynling
laserstrålning, som överskrider gränsen för laserklass 1.

Precaution to replace Optical block
(SF-P101NR)

Body or clothes electrostatic potential could ruin
laser diode in the optical block. Be sure ground
body and workbench, and use care the clothes
do not touch the diode.

1) After the connection, remove solder shown in
the right figure.

PICK-UP Assy P.C.B

Solder

3

ELECTRICAL MAIN PARTS LIST

REF. NO PART NO. KANRI DESCRIPTION

NO.

IC
87-A21-550-010 IC,TA2149N

87-A21-185-040 C-IC,LC72121M
87-A21-064-010 IC,LA4227<1EZ>
87-A21-090-010 IC,LA4600<3LH,3HA>
87-A21-520-040 C-IC,M61509FP

87-A20-446-010 C-IC,LA9241ML
87-A20-459-010 C-IC,LC78622ED
87-A21-093-010 IC,LA6541D
8A-CH4-661-010 C-IC,LC867132V-5P07
87-A20-650-010 IC,RPM6938-V11

87-A21-431-010 IC,BA4560N

TRANSISTOR

89-327-143-080 TR,2SC2714 (0.1W)
87-026-447-080 TR,2SC1740S R
89-111-624-080 TR,2SA1162Y
87-026-213-080 CHIP-TR,DTC114YK
89-503-025-010 C-FET,2SK302GR<1EZ>

89-320-011-080 TR,2SC2001 (15W)<1EZ>
87-026-230-080 CHIP-TR,DTA114YK<1EZ>
89-327-125-080 CHIP TR,2SC2712GR
89-318-154-080 TR,2SC1815 (0.4W)
89-112-965-080 TR,2SA1296 (0.75W)

87-026-463-080 TR,2SA933S (0.3W)
87-026-291-080 TR,DTC124XS
89-213-702-080 TR,2SB1370E
87-026-462-080 TR,2SC1740 S(RS 0.3W)
89-109-332-380 TR,2SA933RS

89-113-187-080 TR,2SA1318TU
87-026-295-080 TR,DTC144TK
87-026-239-080 TR,DTC114TK (0.2W)
87-026-210-080 CHIP-TR,DTC144EK
87-026-237-080 CHIP-TR,DTC124XK

87-026-464-080 TR,DTC114TS (0.3W)

DIODE
87-070-345-080 DIODE,IN4148

87-A40-616-070 VARI-CAP,SVC384(S/T)
87-A40-128-080 C-VARI-CAP,HVU202A
87-017-072-080 ZENER,HZS3B1
87-027-607-080 ZENER,HZ7B3L

87-A40-648-080 ZENER,MTZJ8.2A
87-017-978-080 DIODE,1N4003
87-020-465-080 DIODE,1SS133 (110MA)
87-027-702-080 DIODE,ZENER HZ6C2L (200MA)
87-A40-465-010 DIODE,FR202

MAIN C.B
C30 87-010-260-080 CAP, ELECT 47-25V<1EZ>

C263 87-010-178-080 CHIP CAP 1000P
C264 87-010-178-080 CHIP CAP 1000P
C265 87-010-263-080 CAP, ELECT 100-10V<1EZ>
C266 87-010-545-080 CAP, ELECT 0.22-50V<3LH,3HA>

C266 87-010-263-080 CAP, ELECT 100-10V<1EZ>
C267 87-010-545-080 CAP, ELECT 0.22-50V
C267 87-010-112-080 CAP, ELECT 100-16V<1EZ>
C268 87-010-112-080 CAP, ELECT 100-16V<1EZ>
C271 87-010-221-080 CAP, ELECT 470-10V

C272 87-010-221-080 CAP, ELECT 470-10V
C277 87-010-404-080 CAP, ELECT 4.7-50V<3LH,3HA>
C278 87-010-405-080 CAP, ELECT 10-50V<1EZ>
C278 87-010-263-080 CAP, ELECT 100-10V
C279 87-010-263-080 CAP, ELECT 100-10V<3LH,3HA>

C279 87-010-385-080 CAP, ELECT 220-25V<1EZ>
C301 87-016-495-000 CAP,E 3300-25 M SMG

REF. NO PART NO. KANRI DESCRIPTION

NO.

C306 87-010-404-080 CAP, ELECT 4.7-50V
C307 87-010-401-080 CAP, ELECT 1-50V
C308 87-010-221-080 CAP, ELECT 470-10V
C311 87-010-263-080 CAP, ELECT 100-10V
C312 87-010-385-080 CAP, ELECT 220-25V

C321 87-010-197-080 CAP, CHIP 0.01 DM
C322 87-010-263-080 CAP, ELECT 100-10V
C325 87-010-405-080 CAP, ELECT 10-50V
C401 87-010-403-080 CAP, ELECT 3.3-50V
C402 87-010-197-080 CAP, CHIP 0.01 DM

C403 87-010-263-080 CAP, ELECT 100-10V
C404 87-010-248-080 CAP, ELECT 220-10V
C405 87-010-197-080 CAP, CHIP 0.01 DM
C406 87-010-374-080 CAP, ELECT 47-10V
C407 87-010-178-080 CHIP CAP 1000P

C408 87-010-198-080 CAP, CHIP 0.022
C409 87-010-248-080 CAP, ELECT 220-10V
C410 87-010-263-080 CAP, ELECT 100-10V
C411 87-A11-177-080 C-CAP,S 0.15-16 K B
C412 87-010-401-080 CAP, ELECT 1-50V

C413 87-016-369-080 C-CAP,S 0.033-25 B K
C414 87-010-405-080 CAP, ELECT 10-50V
C416 87-010-545-080 CAP, ELECT 0.22-50V
C417 87-012-157-080 C-CAP,S 330P-50 CH
C418 87-010-213-080 C-CAP,S 0.015-50 B

C419 87-A11-608-080 C-CAP,S 0.33-25 K B
C420 87-016-369-080 C-CAP,S 0.033-25 B K
C421 87-A11-177-080 C-CAP,S 0.15-16 K B
C422 87-010-184-080 CHIP CAPACITOR 3300P(K)
C423 87-010-992-080 C-CAP,S 0.047-25 B

C424 87-A11-606-080 C-CAP,S 0.22-25 K B
C425 87-010-176-080 C-CAP,S 680P-50 SL
C426 87-A11-608-080 C-CAP,S 0.33-25 K B
C428 87-010-197-080 CAP, CHIP 0.01 DM
C429 87-010-186-080 CAP,CHIP 4700P

C430 87-012-156-080 C-CAP,S 220P-50 CH
C431 87-010-545-080 CAP, ELECT 0.22-50V
C432 87-010-374-080 CAP, ELECT 47-10V
C433 87-010-401-080 CAP, ELECT 1-50V
C434 87-010-184-080 CHIP CAPACITOR 3300P(K)

C435 87-010-197-080 CAP, CHIP 0.01 DM
C436 87-010-374-080 CAP, ELECT 47-10V
C437 87-010-404-080 CAP, ELECT 4.7-50V
C438 87-016-669-080 C-CAP,S 0.1-25 K B
C439 87-010-178-080 CHIP CAP 1000P

C440 87-010-145-080 CAP, CHIP 1P CH
C441 87-010-197-080 CAP, CHIP 0.01 DM
C442 87-010-313-080 CAP, CHIP 18P
C445 87-012-368-080 C-CAP,S 0.1-50 F
C446 87-012-368-080 C-CAP,S 0.1-50 F

C447 87-012-368-080 C-CAP,S 0.1-50 F
C448 87-010-315-080 C-CAP,S 27P-50 CH
C450 87-012-140-080 CAP 470P
C451 87-012-156-080 C-CAP,S 220P-50 CH
C455 87-010-247-080 CAP, ELECT 100-50V

C457 87-010-312-080 C-CAP,S 15P-50 CH
C458 87-010-312-080 C-CAP,S 15P-50 CH
C459 87-010-263-080 CAP, ELECT 100-10V
C460 87-015-819-080 CAPACITOR,0.01
C461 87-010-197-080 CAP, CHIP 0.01 DM

C462 87-010-248-080 CAP, ELECT 220-10V
C463 87-010-197-080 CAP, CHIP 0.01 DM
C465 87-010-404-080 CAP, ELECT 4.7-50V
C466 87-012-368-080 C-CAP,S 0.1-50 F
C467 87-010-263-080 CAP, ELECT 100-10V

C469 87-012-154-080 C-CAP,S 150P-50 CH
C470 87-010-544-080 CAP, ELECT 0.1-50V
C471 87-010-196-080 CHIP CAPACITOR,0.1-25
C472 87-015-785-080 CHIP CAPACITOR, 0.1FZ-25Z
C473 87-010-196-080 CHIP CAPACITOR,0.1-25

4

REF. NO PART NO. KANRI DESCRIPTION

NO.

C474 87-015-785-080 CHIP CAPACITOR, 0.1FZ-25Z
C475 87-010-197-080 CAP, CHIP 0.01 DM
C476 87-010-236-080 CAP,E 1000-10 SME
C477 87-010-197-080 CAP, CHIP 0.01 DM
C478 87-010-263-080 CAP, ELECT 100-10V

C479 87-010-197-080 CAP, CHIP 0.01 DM
C480 87-010-221-080 CAP, ELECT 470-10V
C481 87-010-405-080 CAP, ELECT 10-50V
C482 87-010-405-080 CAP, ELECT 10-50V
C489 87-012-368-080 C-CAP,S 0.1-50 F

C490 87-012-368-080 C-CAP,S 0.1-50 F
C491 87-010-197-080 CAP, CHIP 0.01 DM
C492 87-010-221-080 CAP, ELECT 470-10V
C493 87-015-819-080 CAP, CHIP 0.01 KB
C494 87-010-197-080 CAP, CHIP 0.01 DM

C495 87-016-669-080 C-CAP,S 0.1-25 K B
C501 87-012-368-080 C-CAP,S 0.1-50 F
C502 87-010-322-080 C-CAP,S 100P-50 CH
C503 87-010-322-080 C-CAP,S 100P-50 CH
C504 87-010-322-080 C-CAP,S 100P-50 CH

C505 87-010-322-080 C-CAP,S 100P-50 CH
C506 87-010-322-080 C-CAP,S 100P-50 CH
CN202 8A-CH4-693-010 CONN,5P V
CN205 87-A60-109-010 CONN,2P V S2M-2W
CN301 8A-CH4-689-010 CONN,3P V 2.5

CN401 87-A60-424-010 CONN,16P V TOC-B
CN403 87-099-201-010 CONN,8P 6216 H
CN802 8A-CH4-687-010 CONN,4P V 2.5
CNA402 8A-CD9-625-010 CONN ASSY,6P CD-ME
L401 87-003-102-080 COIL, 10UH

L404 87-003-152-080 COIL, 100UH
SFR430 87-024-437-080 SFR100K,RH063EC
X401 8Z-CD5-633-010 VIB, CER16.93MHZ FCR16.93M2

TU C.B
C1 87-010-312-080 C-CAP,S 15P-50V

C2 87-010-316-080 C-CAP,S 33P-50 CH
C3 87-010-312-080 C-CAP,S 15P-50V
C5 87-016-669-080 C-CAP,S 0.1-25 K B<3LH,3HA>
C5 87-012-360-080 CAP, CER 1-10<1EZ>

C6 87-010-313-080 CAP, CHIP 18P<3LH,3HA>
C7 87-014-049-080 CAP,PP 470P-100 J
C8 87-012-349-080 C-CAP,S 1000P-50 CH
C10 87-010-197-080 CAP, CHIP 0.01 DM
C11 87-010-197-080 CAP, CHIP 0.01 DM

C12 87-010-197-080 CAP, CHIP 0.01 DM
C13 87-010-150-080 C-CAP,S 6P-50 CH
C14 87-010-303-080 C-CAP,S 330P-50CH
C15 87-010-178-080 CHIP CAP 1000P
C16 87-010-374-080 CAP, ELECT 47-10V

C17 87-010-198-080 CAP, CHIP 0.022
C18 87-015-835-080 C-CAP,0.047 D
C19 87-010-263-080 CAP, ELECT 100-10V
C20 87-010-404-080 CAP, ELECT 4.7-50V
C21 87-010-197-080 CAP, CHIP 0.01 DM

C22 87-010-197-080 CAP, CHIP 0.01 DM
C23 87-010-197-080 CAP, CHIP 0.01 DM
C24 87-010-303-080 C-CAP,S 330P-50CH
C25 87-016-460-080 C-CAP,S 0.22-16 B
C27 87-A11-067-080 C-CAP,S 1-10 K B

C28 87-016-669-080 C-CAP,S 0.1-25 K B
C29 87-016-669-080 C-CAP,S 0.1-25 K B
C30 87-010-220-080 C-CAP,S 0.018-50 B<1EZ>
C30 87-012-365-080 CAP, CHIP 0.027<3LH,3HA>
C31 87-010-220-080 C-CAP,S 0.018-50 B<1EZ>

C31 87-012-365-080 CAP, CHIP 0.027<3LH,3HA>
C33 87-012-358-080 C-CAP,S 0.47-10 F Z
C34 87-012-358-080 C-CAP,S 0.47-10 F Z
C35 87-015-819-080 CAPACITOR,0.01

REF. NO PART NO. KANRI DESCRIPTION

NO.

C36 87-010-263-080 CAP, ELECT 100-10V
C37 87-010-197-080 CAP, CHIP 0.01 DM
C38 87-010-263-080 CAP, ELECT 100-10V
C39 87-010-404-080 CAP, ELECT 4.7-50V
C40 87-010-197-080 CAP, CHIP 0.01 DM

C41 87-010-178-080 CHIP CAP 1000P
C42 87-010-178-080 CHIP CAP 1000P
C43 87-010-178-080 CHIP CAP 1000P
C44 87-010-311-080 CAP 12P
C45 87-010-312-080 C-CAP,S 15P-50 CH

C46 87-010-197-080 CAP, CHIP 0.01 DM
C47 87-010-197-080 CAP, CHIP 0.01 DM
C48 87-010-197-080 CAP, CHIP 0.01 DM
C49 87-012-140-080 CAP 470P
C50 87-010-197-080 CAP, CHIP 0.01 DM

C51 87-010-316-080 C-CAP,S 33P-50 CH<1EZ>
C52 87-010-197-080 CAP, CHIP 0.01 DM<1EZ>
C53 87-010-197-080 CAP, CHIP 0.01 DM<1EZ>
C54 87-014-055-080 CAP,PP 820P-100 J<1EZ>
C55 87-010-197-080 CAP, CHIP 0.01 DM<1EZ>

C71 87-010-197-080 CAP, CHIP 0.01 DM
C72 87-010-263-080 CAP, ELECT 100-10V
C73 87-010-197-080 CAP, CHIP 0.01 DM
C75 87-010-197-080 CAP, CHIP 0.01 DM
C91 87-012-140-080 CAP 470P

C92 87-010-197-080 CAP, CHIP 0.01 DM
C93 87-010-197-080 CAP, CHIP 0.01 DM
CF1 87-A91-094-010 FLTR,CDA10.7 MG80A
CF2 87-008-261-010 FILTER, SFE10.7MA5-A
CF3 87-008-261-010 FILTER, SFE10.7MA5-A

CN2 87-099-854-010 CONN,6P S2M-6W
CN3 87-A60-110-010 CONN,4P V S2M-4W
HD1 88-CD6-661-010 HLDR,BAR ANT.
HD2 88-CD6-661-010 HLDR,BAR ANT.
L2 87-A50-560-010 COIL,FM BPF(ACD)

L3 8A-CH4-670-010 BAR-ANT,MW 2B-ACH(COI)<3LH,3HA>
L3 8A-CH4-671-010 BAR-ANT,MW/LW 3B-ACH(COI)<1EZ>
L4 87-A50-420-010 COIL,MW OSC(SYN)
L5 87-A50-566-010 COIL,FM RF EX(ACH)
L6 87-A50-567-010 COIL,FM OSC(ACH)

L7 87-A91-308-010 FLTR,PCFAZH- 450T (TOK)
L8 87-005-849-080 COIL,10UH(CECS)
L51 87-A50-421-010 COIL,LW OSC(SYN)<1EZ>
L601 87-003-102-080 COIL, 10UH
TC1 87-011-254-080 TRIMER,20P LAR

TC51 87-A91-659-010 TRIMMER,50P 4.0X4.5 ECRL<1EZ>
X1 87-A70-061-010 VIB,XTAL 4.500MHZ CSA-309

TAPE C.B

C211 87-010-805-080 CAP, S 1-16
C212 87-010-805-080 CAP, S 1-16
C215 87-016-460-080 C-CAP,S 0.22-16 B
C216 87-016-460-080 C-CAP,S 0.22-16 B
C231 87-010-213-080 C-CAP,S 0.015-50 B

C232 87-010-213-080 C-CAP,S 0.015-50 B
C233 87-A10-201-080 C-CAP,S0.33-16 KB
C234 87-A10-201-080 C-CAP,S0.33-16 KB
C235 87-016-669-080 C-CAP,S 0.1-25 K B
C236 87-016-669-080 C-CAP,S 0.1-25 K B

C237 87-010-371-080 CAP, ELECT 470-6.3V
C239 87-010-197-080 CAP, CHIP 0.01 DM
C240 87-010-197-080 CAP, CHIP 0.01 DM
C247 87-010-401-080 CAP, ELECT 1-50V
C248 87-010-401-080 CAP, ELECT 1-50V

C310 87-010-248-080 CAP, ELECT 220-10V
C483 87-012-156-080 C-CAP,S 220P-50 CH<3LH,3HA>
C484 87-012-156-080 C-CAP,S 220P-50 CH<3LH,3HA>
C801 87-010-248-080 CAP, ELECT 220-10V
C805 87-012-365-080 C-CAP,S 0.027-25VBK

5

REF. NO PART NO. KANRI DESCRIPTION

NO.

C806 87-012-365-080 C-CAP,S 0.027-25VBK
C807 87-010-405-080 CAP, ELECT 10-50V
C808 87-010-405-080 CAP, ELECT 10-50V
C809 87-010-401-080 CAP, ELECT 1-50V
C810 87-010-401-080 CAP, ELECT 1-50V

C811 87-010-178-080 CHIP CAP 1000P
C812 87-010-178-080 CHIP CAP 1000P
C816 87-010-180-080 C-CER 1500P
C817 87-010-180-080 C-CER 1500P
C819 87-010-426-080 C-CAP,S 0.012-25 B<3LH,3HA>

C820 87-010-426-080 C-CAP,S 0.012-25 B<3LH,3HA>
C821 87-010-401-080 CAP, ELECT 1-50V
C822 87-010-401-080 CAP, ELECT 1-50V
C823 87-010-178-080 CHIP CAP 1000P
C824 87-010-178-080 CHIP CAP 1000P

C829 87-010-178-080 CHIP CAP 1000P
C830 87-010-178-080 CHIP CAP 1000P
C831 87-010-198-080 CAP, CHIP 0.022
C833 87-018-195-080 CAP, CER 1200P-16V
C834 87-010-248-080 CAP, ELECT 220-10V

C835 87-010-322-080 C-CAP,S 100P-50 CH
C836 87-010-322-080 C-CAP,S 100P-50 CH
C843 87-010-197-080 CAP, CHIP 0.01 DM
C844 87-018-124-080 CAP, CER 270P-50V
C845 87-010-178-080 CHIP CAP 1000P

C846 87-010-263-080 CAP, ELECT 100-10V
C851 87-010-186-080 CAP,CHIP 4700P
C852 87-010-178-080 CHIP CAP 1000P
C853 87-018-211-080 CAP, CER 0.01-50
CN201 87-099-018-010 CONN,16P

CN801 87-A60-110-010 CONN,4P V S2M-4W
CNA302 8A-CD9-629-010 CONN ASSY,6P MA-TU
L801 87-007-342-010 COIL,OSC 85K BIAS
SW801 8Z-CD9-609-010 SW,SL 1-6-2 PS62D01

FRONT C.B

C601 87-010-313-080 CAP, CHIP 18P
C602 87-010-315-080 C-CAP,S 27P-50 CH
C603 87-010-319-080 C-CAP,S 56P-50 CH
C604 87-010-312-080 C-CAP,S 15P-50 CH
C605 87-010-317-080 C-CAP,S 39P-50 CH

C607 87-A10-826-080 C-CAP,S 1-10 K B
C608 87-010-196-080 CHIP CAPACITOR,0.1-25
C611 87-012-368-080 C-CAP,S 0.1-50 F
C612 87-A10-189-040 CAP,E 220-10
C613 87-010-495-040 CAP,E 2.2-50 GAS

C614 87-010-196-080 CHIP CAPACITOR,0.1-25
C615 87-010-493-040 CAP,E 0.47-50 GAS
C616 87-010-494-040 CAP,E 1-50 GAS
C617 87-010-178-080 CHIP CAP 1000P
C618 87-010-560-040 CAP,E 10-50 GAS

C620 87-015-785-080 CHIP CAPACITOR, 0.1FZ-25Z
C627 87-A10-826-080 C-CAP,S 1-10 K B
CN601 87-099-033-010 16P 6216 H
CN602 87-099-201-010 CONN,8P 6216 H
CNA603 8A-CD9-624-010 CONN ASSY,4P TU-FR

CNA604 8A-CH9-623-010 CONN ASSY,2P KEY
LCD601 8Z-CH4-635-010 LCD,HLC7365 ZCH-4
LED601 88-CD6-630-010 LED,934ID RED
LED602 88-CD6-630-010 LED,934ID RED
LED603 88-CD6-630-010 LED,934ID RED

LED604 88-CD6-630-010 LED,934ID RED
LED606 88-CD6-630-010 LED,934ID RED
LED607 88-CD6-630-010 LED,934ID RED
LED608 88-CD6-630-010 LED,934ID RED
LED610 88-CD6-631-010 LED,934GD GRN

S601 87-A91-704-080 SW,TACT EVQ 214 05R
S602 87-A91-704-080 SW,TACT EVQ 214 05R
S603 87-A91-704-080 SW,TACT EVQ 214 05R

REF. NO PART NO. KANRI DESCRIPTION

S604 87-A91-704-080 SW,TACT EVQ 214 05R
S605 87-A91-704-080 SW,TACT EVQ 214 05R

S606 87-A91-704-080 SW,TACT EVQ 214 05R
S607 87-A91-704-080 SW,TACT EVQ 214 05R
S608 87-A91-704-080 SW,TACT EVQ 214 05R
S614 87-A91-704-080 SW,TACT EVQ 214 05R
X601 87-030-273-010 VIB,XTAL 32.768K5PPM
X602 87-030-376-080 VIB,CER CSA5.76MG200

VOL C.B
CN608 84-722-632-010 CONN,2P H

S614 8Z-CT6-636-080 SW,TACT EVQJAC04M
S615 8Z-CT6-636-080 SW,TACT EVQJAC04M

HP C.B

CN204 87-A60-685-010 CONN,4P H WHT EH
CNA203 8A-CD9-628-010 CONN ASSY,3P MA-HP
CNA605 87-A60-113-010 CONN,2P H S2M-2WR
J251 87-A60-569-010 JACK,HTJ-035-18
S609 87-A91-704-080 SW,TACT EVQ214 05R

S610 87-A91-704-080 SW,TACT EVQ214 05R
S611 87-A91-704-080 SW,TACT EVQ214 05R
S612 87-A91-704-080 SW,TACT EVQ214 05R
S613 87-A91-704-080 SW,TACT EVQ214 05R

BATT1 C.B

C901 87-010-192-080 C-CAP,S 0.022-50 F
C902 87-010-192-080 C-CAP,S 0.022-50 F
C903 87-010-192-080 C-CAP,S 0.022-50 F
C904 87-010-192-080 C-CAP,S 0.022-50 F
CNA901 8A-CD9-627-010 CONN ASSY,3P PWR

!

PR901 87-A90-092-080 PROTECTOR,2.5A 491

MOTOR C.B

M2 9X-262-576-910 MOTOR GEAR ASSY
PIN3 91-564-722-110 CONNECTOR 6P
SW1 91-572-085-120 LEAF SW

BATT2 C.B

NO.

6

• Regarding connectors, they are not stocked as they are not the initial order items.

The connectors are available after they are supplied from connector manufacturers upon the order is received.

CHIP RESISTOR PART CODE

Chip Resistor Part Coding

88

LCD DISPLAY
LCD, HLC7365 ZCH-4

A

Resistor Code

Chip resistor

Wattage Type Tolerance
1/16W 1005 5% CJ

1/16W
1/10W

1/8W

1608
2125

3216

5%
5%

5%

TRANSISTOR ILLUSTRATION

Symbol

CJ
CJ

CJ

Figure

Value of resistor

Form

L

Dimensions (mm)

t

W

0.55

Resistor Code

108
118

128

LW t

1.0 0.5 0.35 104

1.6 0.8 0.45
2 1.25 0.45

3.2

1.6

: A
: A

ECB

2SB1370E

ECB

DTC114TS

S

D

G

2SK302GR

C

B

E

2SA1162Y
2SC2712
2SC2714
DTC114TK
DTC114YK
DTC124XK
DTC144EK

ECB

2SA933RS
2SC1740S R
DTC124XS

ECB

2SA933S
2SA1296
2SA1318TU
2SC1740 S
2SC1815
2SC2001

87

WIRING-1 (MAIN/TAPE: EZ)

1

A

B

C

D

234567

8

9

10

11 12 13

14

E

F

G

H

I

J

K

109

SCHEMATIC DIAGRAM-1 (MAIN 1/2: TAPE)

BATT1

BATT2

1211

WIRING-2 (MAIN/TAPE: LH, HA)

1

A

B

C

D

234567

8

9

10

11 12 13

14

E

F

G

H

I

J

K

1413

SCHEMATIC DIAGRAM-2 (MAIN 2/2)

1615

WIRING-3 (FRONT)

1

A

B

C

D

234567

8

9

10

11 12 13

14

E

F

G

H

I

J

K

1817

SCHEMATIC DIAGRAM-3 (FRONT)

2019

SCHEMATIC DIAGRAM-4 (TU: EZ)

2221

WIRING-4 (TU: EZ)

1

A

B

C

D

234567

E

F

G

H

I

J

K

23

WIRING-5 (TU: LH, HA)

1

A

B

C

D

234567

E

F

G

H

I

J

K

24

SCHEMATIC DIAGRAM-5 (TU: LH, HA)

2625

WIRING-6 (HP/BATT/MOTOR)

1

A

B

C

D

234567

8

9

10

11 12 13

14

E

F

M

OTOR C.B

M2

G

+

(SLED MOTOR)

_

M2

SW1

(INSIDE LIMIT SW)

H

M3

(SPINDLE MOTOR)

SW1

PIN3

CNA402

I

TO MAIN C.B

_

+

M3

J

K

2827

ELECTRICAL ADJUSTMENT

L003

(BAR-ANT)

5

13

TU C.B

3

L007

IC001

L005

L006

TC051

EZ MODEL

L004

L051

TC001

EZ MODEL

3

7

2

4

6

HP C.B

J251

90

TAPE C.B

C39

+

246

L801

8

0

M1

(DECK MOTOR)

9

29

< TUNER SECTION >
(LH/HA MODEL)

1. AM IF Adjustment

L007 ....................................................................... 450kHz

2. AM VT Adjustment
Settings: • Test point: C39+

• Adjustment location: L004

Method: Set to AM 1000kHz adjust L004 so that the test

point becomes 3.7V±0.02V

< TAPE SECTION >

8. Bias frequency Adjustment

L801 ............................................................. 75Hz ±500Hz

9. Tape speed Adjustment
Settings: • Test tape: TTA-100

• Test point: PHONES JACK (J251)

• Adjustment location: SFR of deck motor

Method: Play back the test tape and adjust so that the

output frequency is 3000Hz ±30Hz.

3. AM Tracking Adjustment

L003 ....................................................................... 600kHz

TC001, L007 ........................................................ 1400kHz

4. FM VT Adjustment
Settings: • Test point: C39+

• Adjustment location: L006

Method: Set to FM 108MHz adjust L006 so that the test

point becomes 6.0V±0.2V

5. FM Tracking Adjustment

L005 ........................................................................98MHz

(EZ MODEL)

1. MW IF Adjustment

L007 ....................................................................... 450kHz

2. MW VT Adjustment
Settings: • Test point: C39+

• Adjustment location: L004

Method: Set to MW 999kHz adjust L004 so that the test

point becomes 3.7V±0.02V

3. MW Tracking Adjustment

L003 ....................................................................... 603kHz

TC001, L007 ........................................................ 1404kHz

10. Azimuth Adjustment
Settings: • Test tape: TTA-320

• Test point: PHONES JACK (J251)

• Adjustment location: Azimuth adjustment
screw

Method: Play back the test tape and adjust so that the

output is maximum.

4. FM VT Adjustment
Settings: • Test point: C39+

• Adjustment location: L006

Method: Set to FM 108MHz adjust L006 so that the test

point becomes 6.0V±0.2V

5. FM Tracking Adjustment

L005 ........................................................................98MHz

6. LW VT Adjustment
Settings: • Test point: C39+

• Adjustment location: L004

Method: Set to LW 288kHz adjust L004 so that the test

point becomes 4.60V±0.02V

7. LW Tracking Adjustment

L003 ....................................................................... 153kHz

TC051..................................................................... 288kHz

30

PRACTICAL SERVICE FIGURE

< TUNER SECTION >

< FM SECTION >

IHF Sensitiviy: Less than 18dB
(THD 3%) (at 76/87.5, 83/98, 108MHz)
Signal to Noise Ratio: Mono: More than 66dB
(Input 60dB) Stereo: More than 65dB
Distortion:
(Input: 60dB) Less than 2% (at 98MHz)
(Input: 120dB) Less than 3% (at 98MHz)
Auto stop level: 28dB±8dB (at 98MHz)
Stereo separation: More than 25dB (at 98MHz)
Intermediate frequency: 10.7MHz

< AM/MW SECTION >

Sensitivity: Less than 48dB
(S/N 10dB) (at 600/603kHz)

Less than 46dB
(at 1000/999kHz)
Less than 44dB
(at 1400/1404kHz)

Signal to Noise Ratio: More than 30dB

(at 600/603, 1000/999, 1400/

1404kHz)
Distortion:
(Input: 74dB) Less than 3% (at 1000/999kHz)
(Input: 75dB) Less than 10%

(at 1000/999kHz)
Auto stop level: Less than 60dB

(at 1000/999kHz)
Intermediate frequency: 450kHz

< LW SECTION > (EZ model only)

Sensitivity: Less than 60dB
(S/N 10dB) (at 153kHz)

Less than 56dB

(at 198kHz)

Less than 52dB

(at 288kHz)
Signal to Noise Ratio: More than 30dB
(Input 80dB) (at 153/198/288kHz)
Distortion:
(Input: 80/120dB) Less than 3% (at 198kHz)
Auto stop level: Less than 70dB (at 198kHz)

< DECK SECTION >

Tape speed: 3000Hz±60Hz
Wow & flutter: Less than 0.3% (R.M.S)
Take-up torque: 30-60g-cm (FWD)
FF&REW torque: 55-140g-cm
Distortion: Less than 5% (REC/PB, 1kHz)
S/N ratio: More than 35dB (PB, AC, DC)

More than 25dB

(REC/PB, AC, DC)
Max Noise level: Less than 45mV

(PB, VOL MAX)
Erasing Ratio: More than 45dB
Test tape: TTA-100

TTA-602 (NORMAL)

TTA-615 (HIGH POSITION)

31

IC BLOCK DIAGRAM
IC, TA2149N

IC, LC72121M

32

IC, M61509FP

INA1

INB1

INC1

IND1

INE1

QF1

QF2

TONEH1

TONEL1

OUT1

GND

VDD

10

11

1

2

3

4

5

6

7

8

9

VOL VOL

Treble
boost

ATT ATT

Bass
boost

Mono.SW

MUTE

Treble
boost

Bass
boost

Control logic

24

23

22

21

20

19

18

17

16

15

14

1312

INA2

INB2

INC2

IND2

INE2

QF4

QF3

TONEH2

TONEL2

OUT2

VSS

CONT

IC, LA4227

33

IC, LA6541D

IC, LA4600

R IN

GND

L IN

10

9

8

RN11

RN12

STANDBY SW

7

STANDBY SW

CH1
INPUT AMP

REF
AMP

CH2
INPUT AMP

NOISE
PREVENTION

Rf1

Rf2

PRE DRIVE
AMP

PRE DRIVE
AMP

Vcc

4

OUTPUT
AMP

TSD PROTECTER

OUTPUT
AMP

REPLE FILTER

1

2

3

R OUT

GND

L OUT

P.P

56

FILTER

34

IC, BA4560N

35

IC DESCRIPTION
IC, LA9241ML

Pin No. Pin Name I/O Description

1

2

FIN2

FIN1

Pin to which external pickup photo diode is connected. RF signal is created by adding

I

with the FIN1 pin signal. FE signal is created by subtracting from the FIN1 pin signal.

I

Pin to which external pickup photo diode is connected.

10
11

12

13
14
15
16

17

3

4
5
6
7

8

9

E

F

TB

TE–

TE

TESI

SCI
TH
TA

TD–

TD

JP
TO
FD

FD–

Pin to which external pickup photo diode is connected. TE signal is created by

I

subtracting from the F pin signal.

I

Pin to which external pickup photo diode is connected.

I

DC component of the TE signal is input.

I

Pin to which external resistor setting the TE signal gain is connected between the TE pin.

O

TE signal output pin.
TES “Track Error Sense” comparator input pin. TE signal is passed through a band-

I

pass filter then input.

I

Shock detection signal input pin.

I

Tracking gain time constant setting pin.

O

TA amplifier output pin.
Pin to which external tracking phase compensation constants are connected between

I

the TD and VR pins.

I

Tracking phase compensation setting pin.

I

Tracking jump signal (kick pulse) amplitude setting pin.

O

Tracking control signal output pin.

O

Focusing control signal output pin.
Pin to which external focusing phase compensation constants are connected between

I

the FD and FA pins.

18

19

20
21
22
23
24
25

26

27
28

29
30, 31
32, 33

34

FA

FA–

FE

FE–

AGND

SP

SPI

SPG

SP–

SPD

SLEQ

SLD

SL–, SL+

JP–, JP+

TGL

—
—

Pin to which external focusing phase compensation constants are connected between

I

the FD– and FA– pins.
Pin to which external focusing phase compensation constants are connected between

I

the FA and FE pins.

O

FE signal output pin.

I

Pin to which external FE signal gain setting resistor is connected between the FE pin.
Analog signal GND.
No connection.

O

Single ended output of the CV+ and CV– pin input signal.

I

Pin to which external spindle gain setting resistor in 12 cm mode is connected.
Pin to which external spindle phase compensation constants are connected together

I

with SPD pin.

O

Spindle control signal output pin.

I

Pin to which external sled phase compensation constants are connected.

O

Sled control signal output pin.

I

Sled advance signal input pin from microprocessor.

I

Tracking jump signal input pin from DSP.

I

Tracking gain control signal input from DSP. Low gain when TGL = H.

35

TOFF

I

Tracking off control signal input pin from DSP. Off when TOFF = H.

36

Pin No. Pin Name I/O Description

36

TES

O

Pin from which TES signal is output to DSP.

37

38

39, 40

41

42

43

44
45
46
47
48
49
50
51
52
53
54

HFL

SLOF

CV–, CV+

RFSM

RFS–

SLC

SLI

DGND

FSC

TBC

NC
DEF
CLK

CL

DAT

CE

DRF

—

—

“High Frequency Level” is used to judge whether the main beam position is on top of

O

bit or on top of mirror.

I

Sled servo off control input pin.

I

CLV error signal input pin from DSP.

O

RF output pin.
RF gain setting and EFM signal 3T compensation constant setting pin together with

I

RFSM pin.
“Slice Level Control” is the output pin which controls the RF signal data slice level by

O

DSP.

I

Input pin which control the data slice level by the DSP.
Digital system GND.

O

Output pin to which external focus search smoothing capacitor is connected.

I

“Tracking Balance Control” EF balance variable range setting pin.
No connection.

O

Disc defect detector output pin.

I

Reference clock input pin. 4.23 MHz of the DSP is input.

I

Microprocessor command clock input pin.

I

Microprocessor command data input pin.

I

Microprocessor command chip enable input pin.

O

“Detect RF” RF level detector output.
55
56
57
58
59
60
61
62
63
64

FSS

VCC2

REFI

VR
LF2
PH1

BH1

LDD

LDS

VCC1

—
—

—

I

“Focus Search Select” focus search mode (± search/+ search) select pin.
Servo system and digital system Vcc pin.
Pin to which external bypass capacitor for reference voltage is connected.

O

Reference voltage output pin.

I

Disc defect detector time constant setting pin.

I

Pin to which external capacitor for RF signal peak holding is connected.

I

Pin to which external capacitor for RF signal bottom holding is connected.

O

APC circuit output pin.

I

APC circuit input pin.
RF system Vcc pin.

37

IC, LC78622ED

Pin No. Pin Name I/O Description

1
2
3

DEFI

TAI

PDO

I

Defect sense signal (DEF) input pin. (Connect to 0V when not used).

I

O

Test signal input pin with built-in pull-down resistor. Be sure to connect to 0V.

Phase comparator output pin to control external VCO.
4
5
6
7
8
9

10
11

12, 13

14

15
16
17
18

19, 20

21

VVSS

ISET

VVDD

FR

VSS

EFMO

EFMIN

T2

CLV+, CLK-

___

V/P

HFL
TES

TOFF

TGL

JP+, JP-

PCK

—

—

—

For PLL.

I

GND pin for built-in VCO. Be sure to connect to 0V.

Pin to which external resistor adjusting the PD0 output current.

Power supply pin for built-in VCO.

I

Pin for VCO frequency range adjustment.

Digital system GND. Be sure to connect to 0V.

O

EFM signal output pin.

For slice level control.

I
I

Test signal input pin with built-in pull-down resistor. Be sure to connect to 0V.

O

Disc motor control output. Three level output is possible using command.

EFM signal input pin.

Rough servo or phase control automatic selection monitoring output pin. Rough servo

O

at H. Phase servo at L.

I

Track detect signal input pin. Schmidt input.

I

Tracking error signal input pin. Schmidt input.

O

Tracking OFF output pin.

O

Tracking gain selection output pin. Gain boost at L.

O

Track jump control signal output pin. Three level output is possible using command.

O

EFM data playback clock monitoring pin 4.3218 MHz when phase is locked in.

22

23
24
25
26
27
28
29
30
31

32, 33

34
35
36
37
38
39
40
41
42

FSEQ

VDD

SL+

SL-

—

PUIN

RW

EMPH

C2F

DOUT

T3, T4

N.C.

MUTEL

LVDD

LCHO
LVSS

RVSS
RCHO
RVDD

MUTER

—

—

—

—

—
—

—

Sync signal detection output pin. H when the sync signal which is detected from EFM

O

signal and thesync signal which is internally generated agree.
Digital system power supply pin.

O

Moves the sled to outer circumference.

O

Moves the sled to inner circumference.
Not connected.

I

CD pickup inner switch detection.

O

Read, wright signal.

O

De-emphasis monitor output pin. De-emphasis disc is being played back at H.

O

C2 flag output pin.

O

DIGITAL OUT output pin. (EIAJ format).

I

Test signal input pin with built-in pull-down resistor. Be sure to connect to 0V.
Not used. Set the pin to open.

O

L-channel 1-bit DAC.

O

L-channel mute output pin.
L-channel power supply pin.
L-channel output pin.
L-channel GND. Be sure to connect to 0V.
R-channel GND. Be sure to connect to 0V.

O

R-channel 1-bit DAC.

R-channel output pin.
R-channel power supply pin.

O

R-channel mute output pin.

38

Pin No. Pin Name I/O Description

43
44

XVDD
XOUT

—

Crystal oscillator power supply pin.

O

Pin to which external 16.9344 MHz crystal oscillator is connected.

45

XIN

I
46
47
48
49
50

51

52

53
54
55
56
57
58
59
60
61
62

63

64

XVSS
SBSY
EFLG

PW

SFSY

SBCK

FSX

WRQ
RWC

SQOUT

COIN

___________

CQCK

RES

T11

16M

4.2M
T5

______

CS

T1

—

Crystal oscillator GND pin. Be sure to connect to 0V.

O

Subcode block sync signal output pin.

O

C1, C2, single and dual correction monitoring pin.

O

Subcode P, Q, R, S, T, U and W output pin.

O

Subcode frame sync signal output pin. Falls down when subcode enters standby.
Subcode read clock input pin. Schmidt input. (Be sure to connected to 0V when not

I

in use.)
Pin outputting the 7.35 kHz sync signal which is generated by dividing frequency of

O

crystal oscillator.

O

Subcode Q output standby output pin.

I

Read/write control input pin. Schmidt input.

O

Subcode Q output pin.

I

Command input pin from microprocessor.

I

Command input read clock or subcode read input clock from SQOUT pin

I

LC78622 reset input pin. Set this pin to L once when the main power is turned on.

O

Test signal output pin. Use this pin as open (normally L output).

O

16.9344 MHz output pin.

O

4.2336 MHz output pin.

I

Test signal input pin with built-in pull-down resistor. Be sure to connect to 0V.
Chip select signal input pin with built-in pull-down resistor. Be sure to connect to 0V

I

while it is not controlling.

I

Test signal input pin without built-in pull-down resistor. Be sure to connect to 0V.

39

IC, LC867132V-5P07

Pin No. Pin Name I/O Description

O

1
2
3

O-RMC/CE

O-DATA

O-CLK

CD read/write control output.

O

Data output to sound processor IC (M62495FP).

O

Clock output to sound processor IC (M62495FP).

10
11
12
13
14
15
16
17
18
19
20
21
22

4
5
6
7
8
9

NC

O-CLK SFT

I-HOLD

I-RST

XT1 (IN)

XT2 (OUT)

VSS1

CF1 (IN)

CF2 (OUT)

VDD1
I-FM ST
I-KEYO

I-CD SW

I-KEY1

I-MOTOR

I-REC

I-FM/AM (NC)

I-TU DO

O-BASS LED (NC)

—

—

—

Not Connected.

O

Clock shift output of the microcomputer.

I

Hold status detection.

I

Microcomputer reset.

I

Connected to 32.768kHz crystal oscillator.

O

GND.

I

Connected to 5.76MHz Ceramic Filter.

O

Power supply for microcomputer (+5V).

I

FM STEREO status input.

I

KEY AD input.

I

CD DOOR SW status detection input.

I

KEY AD input.

I

DECK MECHA MOTOR status input.

I

REC status input.

I

FM, AM status input. (Not connected)

I

Data input from tuner PLL.

O

BASS LED ON/OFF control output. (Not connected)
23
24
25
26
27
28
29
30
31
32
33
34
35
36

37-40

41
42

43-50

O-QS LED

NC

O-INT

I-DRF

I-WRQ

I-REMO

SO/PAO (NC)

S1/PA1 (NC)

S2/PA2
S3/PA3 (NC)
S4/PA4 (NC)
S5/PA5 (NC)

S6/PA6

S7/PA7

S8-S11

VDD3

VSS3

S12-S19

—

—
—

O

Q-Sound LED ON/OFF control output.
Not connected.

O

INT DIODE MATRIX detection output.

I

CD RF level detection input.

I

CD sub-code Q standby input.

I

Remote control input.

O

LCD segment output and initial settings output. (SW) (Not connected)

O

LCD segment output and initial settings output. (LW) (Not connected)

O

LCD segment output and initial settings output. (MW 10K)

O

LCD segment output and initial settings output. (FM WIDE) (Not connected)

O

LCD segment output and initial settings output. (OIRT) (Not connected)

O

LCD segment output and initial settings output. (SW2) (Not connected)

O

LCD segment output and initial settings output. (SYN)

O

LCD segment output and initial settings output.

O

Power supply for microcomputer (+5V).
GND.

O

LCD segment output.

51-54

S20-S23 (NC)

O

LCD segment output. (Not Connected)

40

Pin No. Pin Name I/O Description

55
56
57

O-CD LED
O-TU LED

O-TA LED (NC)

LED ON/OFF control output for CD functions.

O

LED ON/OFF control output for TU functions.

O

LED ON/OFF control output for TAPE functions. (Not Connected)

O
58
59
60
61
62
63

64-66

67
68
69
70
71
72
73
74
75
76
77
78

O-ROCK LED

O-POP LED

O-JAZZ LED

NC
I-CD TEST (NC)
I-TU TEST (NC)

COM0-COM2

NC

VSS2

VDD2
O-CD ON
O-TU ON

O-P.CONT

NC

O-MUTE

O-FM MONO (NC)

O-BEAT CONT

O-QSOUND

O-COIN

—

—
—
—

—

LED ON/OFF control output for ROCK.

O

LED ON/OFF control output for POP.

O

LED ON/OFF control output for JAZZ.

O

I

Not connected.

I

LCD common output.

O

Not connected.
GND.
Power supply for microcomputer (+5V).
CD PWR control output.

O

TU PWR control output.

O

Power supply control output.

O

Not connected
Main mute output.

O

FM force control MONO output. (Not connected)

O

BEAT switch over output.

O

Q-Sound ON/OFF output.

O

CD command output.

O
79
80

I-SQOUT

O-CQCK

CD sub-code Q input.

I

CLK for CD commands/sub-codes.

O

41

MECHANICAL PARTS LIST 1/1

REF. NO PART NO. KANRI DESCRIPTION

NO.

1 87-B00-010-010 BADGE,AIWA 30.5-5.2 S 2.5L
2 8A-CD9-009-010 WINDOW,CASS
3 8A-CD9-232-010 SPR-T,CASS
4 8A-CD9-008-010 BOX,CASS
5 86-CT4-218-010 CUSHION,FOOT/PORON

6 8A-CHK-007-010 WINDOW,LCD RC
7 8A-CHK-002-010 CABI,FR A2K ASSY<1EZ>
7 8A-CHK-004-010 CABI,FR A2K-LH ASSY<3LH,3HA>
8 8A-CD9-202-010 GUIDE,LED
9 M8-ZZK-E90-070 DA11T3C

10 8A-CD9-201-010 HLDR,DISPLAY
11 8A-CD9-622-010 FF-CABLE, 8P CD-FR
12 8A-CD9-020-010 BTN,REPEAT
13 8A-CD9-021-010 BTN,EQ
14 8A-CD9-028-010 BTN,Q/BASS

15 8Z-CD5-634-010 COVER,AC SOCKET
16 84-CD5-215-010 GEAR
17 84-CD5-216-010 BRACKET
18 8A-CD9-022-010 LENS,LED
19 8A-CD9-024-010 KEY,CASS TN21

20 8A-CD9-223-010 SPR-P,REC TN21
21 8A-CD9-212-010 HLDR,PWB R
22 8A-CD9-211-010 HLDR,PWB L
23 88-CD5-602-010 SPKR 4’3.2<3LH,3HA>
23 88-CD9-626-010 SPKR,100 7OHM 3W<1EZ>

24 8A-CD9-222-010 HLDR,SPEAKER
25 8A-CD9-203-010 GUIDE,VOL
26 8A-CD9-014-010 BTN,VOL
27 8A-CH9-006-010 PANEL,VOL CH
28 8A-CD9-007-010 WINDOW,CD

29 8A-CH9-012-010 BOX,CD A
30 88-CD6-661-010 HLDR,BAR ANT.
31 8Z-CH4-225-010 HLDR,CHUCK A(S)
32 84-CD5-217-010 PLATE,MAGNET
33 87-036-368-010 MAGNET

34 8Z-CH4-211-010 BASE,CHUCK
35 8Z-CH4-212-010 RING,CHUCK
36 8A-CD9-005-010 CHAS,CD A
37 8Z-CDB-169-010 PANEL,CD SANYO
38 8A-CD9-231-010 SPR-T,CD

REF. NO PART NO. KANRI DESCRIPTION

39 87-036-389-010 SW,PUSH LOCK

!

40 87-A60-178-010 JACK,AC E W/SW

!

41 8A-CD9-607-010 PT,E 2.5W<1EZ>

!

41 8A-CD9-604-010 PT,H 4.5WT04541A<3LH,3HA>

42 8A-CH4-209-010 HLDR,PT
43 8A-CD9-012-010 HANDL,GRIP

44 8A-CD9-011-010 HANDL,ARM
45 8A-CH4-036-010 PLATE,AC<1EZ>
46 8Z-CH4-640-010 ANT,ROD
47 8A-CD9-010-010 LID,BATT

48 8A-CH9-002-010 CABI,REAR A2
49 87-CD6-213-010 SPR-C,BATT (-)
50 8A-CD9-221-010 HLDR,ANT
51 8A-CD9-620-010 FF-CABLE, 16P FR-MAIN
52 8A-CD9-621-010 FF-CABLE, 16P CD-RF

53 8A-CD9-626-010 CONN ASSY,2P DOOR
54 8A-CD9-019-010 CAP, CD B
55 8A-CD9-018-010 CAP, CD A
56 87-A91-369-010 SW,AC SL 2 2 2 SDKGA41700

57 8A-CD9-630-010 CONN ASSY,4P RPH

58 8A-CD9-633-010 CONN ASSY,4P SP
59 8A-CD9-631-010 CONN ASSY,4P TP-ME
A 87-B10-242-010 UT2+3-30 W/O CR
B 87-741-096-410 UT2+3-10
C 87-B10-239-010 QT2+3-8 W/O CR

D 87-661-097-410 TAPPING SCREW, VFT1+3-12
E 87-751-094-410 VT2+3-6 W10SL0T
F 87-067-566-010 TAPPING SCREW, VFTT+3-6
G 87-571-033-410 TAPPING SCREW, VIT+2-4
H 87-255-096-410 U+3-10 NI

I 87-342-074-010 UT2+2.6-8
J 87-B10-269-010 UT2+3-12 W/O CR
K 87-352-075-210 VT2+2.6-10
L 87-WA5-253-010 W,3.3-10-0.8

NO.

<3LH,3HA>

COLOR NAME TABLE

Basic color symbol Color Basic color symbol Color Basic color symbol Color

B Black C Cream D Orange
G Green H Gray L Blue

LT Transparent Blue N Gold P Pink

R Red S Silver ST Titan Silver

T Brown V Violet W White

WT Transparent White Y Yellow YT Transparent Yellow

LM Metallic Blue LL Light Blue GT Transparent Green
LD Dark Blue DT Transparent Orange

42

MECHANICAL EXPLODED VIEW 1/1

23

24

C

27

28

B

54

26

36

25

29

58

P.C.B

31
32

C

11

C

12

34

35

17

55

33

18

L

16

37

52

L

I

9

51

B

B

P.C.B

C

C

C

24

P.C.B

10

10

LCD

8

B

C

B

38

K

39

D

16

L

I

K

P.C.B

E

B

B

17

56

53

P.C.B

59

15

42

40

43

F

41

D

5

5

A

J

45

46

C

44

47

A

H

GRILLE,
FR L

2

2

1

14

13

19

6

7

5

GRILLE,

3

4

FR R

TN-21ZVC-2000

22

20

57

B

P.C.B

49

P.C.B

P.C.B

48

5

B

J

50

BAR-ANT

30

J

P.C.B

P.C.B

B

B

B

G

21

24

C

23

P.C.B

CHAS,TU A

C

C

24

4443

TAPE MECHANISM EXPLODED VIEW 1/1

F

G

1

E

2

8

10

J
L

14

b

18

19

7

36

46

47

25

9

21

20

22

23

24

c
51

26

27

28

A

6

29

LUG PLATE

52

4

3

a

15
16

17

34

35

C

37

TAPE MECHANISM PARTS LIST 1/1

REF. NO PART NO. KANRI DESCRIPTION

1 S1-921-030-4A0 HEAD BASE
2 S1-821-030-070 AZIMUTH SPRING
3 S1-921-030-090 PANEL P SPRING

5

11

12

13

31

49

30

32

c

b

33

A

4 S1-921-260-050 GEAR PLATE SPRING
5 S1-921-265-020 GEAR PLATE ASSY

6 S1-510-020-020 REC SPRING PLATE
7 S1-921-015-010 CHASSIS ASSY
8 S1-921-030-110 HEAD PANEL
9 S1-921-143-160 BASE ASSY
10 S1-921-141-8A0 M CONTROL SPRING

11 S1-921-260-4A0 SENSING LEVER
12 S1-921-043-100 PINCH ROLLER ARM ASSY
13 S1-921-130-010 EJECT SLIDE LEVER
14 S1-921-141-3A0 P CONTROL SPRING
15 S1-921-140-550 PAUSE LEVER(E)

16 S1-921-140-120 PAUSE LEVER SPRING
17 S1-921-140-110 PAUSE STOPPER
18 S1-921-140-150 BUTTON LEVER SPRING(B)
19 S1-821-011-590 E KICK LEVER
20 S1-921-141-070 BUTTON LEVER SPRING(A)

21 S6-401-011-490 LEAF SW MSW-1541T
22 S1-921-140-090 SWITCH ACTUATOR
23 S1-921-140-080 PUSH BUTTON ACTUATOR
24 S1-921-140-190 PLAY BUTTON LEVER
25 S1-921-030-100 MG ARM SPRING

26 S1-921-140-040 REW BUTTON LEVER
27 S1-921-140-050 FF,BUTTON REVER
28 S1-921-140-060 STOP BUTTON LEVER
29 S1-921-140-600 PAUSE BUTTON LEVER
30 S1-821-100-700 FF GEAR

31 S1-921-050-060 SENSER
32 S1-921-053-100 TAKE UP REEL ASSY
33 S1-829-100-010 PACK SPRING
34 S1-921-050-150 S REEL HUB
35 S1-921-050-220 BACK TENSION SPRING

NO.

a

48

C

REF. NO PART NO. KANRI DESCRIPTION

NO.

36 S1-921-140-030 REC BUTTON LEVER
37 S1-921-140-170 P.S.LEVER SPRING
38 S1-921-073-040 RF CLUTCH ASSY
39 S1-921-070-030 RF BELT
40 S1-921-260-020 CAM GEAR

41 S1-921-140-160 E ACTUATOR SPRING
42 S1-921-093-210 FLYWHEEL ASSY
43 S1-921-090-380 MAIN BELT
44 S1-921-120-590 MOTOR PULLEY
45 S6-002-030-220 MOTOR EG530AD-2B

46 S6-209-100-100 E HEAD PH-K380-MS1
47 S1-921-030-050 MG ARM
48 S1-921-140-210 REC BUTTON LEVER SPRING
49 S1-821-100-690 RECORD SAFETY LEVER
50 S1-821-128-9A0 MOTOR BRACKET

51 S1-821-010-500 PLAY BUTTON LEVER SPRING
52 S6-201-011-110 HEAD,RP7442ES-0951
A S9-P04-200-310 C TAPPING SCREW 2-3
B S1-921-120-020 MOTOR COLLER SCREW
C S9-B10-200-510 P TAPPING BIND SCREW M2-5

D S9-C07-204-510 SCREW,TAPPING(CAMERA)M2-4.5
E S9-P01-200-610 SCREW,M2-6
F S9-B01-200-310 (+)BIND SCREW M2-3
G S9-F08-200-710 AZIMUTH SCREW M2-7
H S1-921-120-030 MB SCREW

I S9-W02-300-100 P WASHER CUT 1.2-3.8-0.3
J S9-W02-500-100 P WASHER CUT 1.45-3.8-0.5
K S9-W01-400-100 P WASHER 2-3.5-0.4
L S9-W01-130-200 P WASHER 2.1-4-0.13

38

39

42

43

D

40

D

K

41

I

B

B

50

H

44

45

4645

CD MECHANISM EXPLODED VIEW 1/1

SHAFT,SLIDE

B

SF-P101NR

CHASSIS

B

1

2

A

A

3

SPINDLE
MOTOR(M3)

CD MECHANISM PARTS LIST 1/1

REF. NO PART NO. KANRI DESCRIPTION

NO.

1 S2-121-A28-400 COVER GEAR
2 S2-511-A21-000 GEAR MIDDLE
3 S2-511-A21-100 GEAR,DRIVE
A S1-PN2-03R-OSE SCR PAN PCS 2-3
B 87-261-073-410 SCR S-TPG FLT 2.6-6

ALL M8-ZZK-E90-070 DA11T3C

MOTOR C,B

47

2–11, IKENOHATA 1–CHOME, TAITO-KU, TOKYO 110, JAPAN TEL:[phone]

737004

Printed in Singapore