CSD-TD31
LHS US
CSD-TD32
UW
SERVICE MANUAL
COMPACT DISC STEREO RADIO
CASSETTE RECORDER
BASIC TAPE MECHANISM : TN-21ZVC-2000
BASIC CD MECHANISM : DA11T3C
S/M Code No. 09-003-342-8N1
DATA
SPECIFICATIONS
Design and specifications are subject to change without
•
notice
.
ACCESSORIES/PACKAGE LIST
REF. NO PART NO. KANRI DESCRIPTION
1 8A-CHB-902-010 IB,LH(ESP)FM<1LH>
1 8A-CHB-903-010 IB,U(ESF)FM<2UW,1US>
!
2 87-A80-036-010 AC CORD SET ASSY,E W/FLTR VOL
!
2 87-A80-109-010 AC CORD,HK7281 BLK U<2UW,1US>
!
3 87-A91-017-010 PLUG,CONVERSION JT-0476<1LH>
NO.
<1LH>
2
PROTECTION OF EYES FROM LASER BEAM DURING SERVICING
CLASS 1
KLASSE 1
LUOKAN 1
KLASS 1
LASER PRODUCT
LASER PRODUKT
LASER LAITE
LASER APPARAT
This set employs laser. Therefore, be sure to follow carefully the
instructions below when servicing.
WARNING!
WHEN SERVICING, DO NOT APPROACH THE LASER EXIT
WITH THE EYE TOO CLOSELY. IN CASE IT IS NECESSARY TO
CONFIRM LASER BEAM EMISSION. BE SURE TO OBSERVE
FROM A DISTANCE OF MORE THAN 30cm FROM THE
SURFACE OF THE OBJECTIVE LENS ON THE OPTICAL
PICK-UP BLOCK.
Caution: Invisible laser radiation when
open and interlocks defeated avoid exposure to beam.
Advarsel:Usynling laserståling ved åbning,
når sikkerhedsafbrydere er ude af funktion.
Undgå udsættelse for stråling.
VAROITUS!
Laiteen Käyttäminen muulla kuin tässä käyttöohjeessa mainitulla tavalla saattaa altistaa käyt-täjän turvallisuusluokan 1 ylittävälle näkymättömälle lasersäteilylle.
CAUTION
Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous
radiation exposure.
ATTENTION
L'utilisation de commandes, réglages ou procédures autres que
ceux spécifiés peut entraîner une dangereuse exposition aux
radiations.
ADVARSEL!
Usynlig laserståling ved åbning, når sikkerhedsafbrydereer ude
af funktion. Undgå udsættelse for stråling.
This Compact Disc player is classified as a CLASS 1 LASER
product.
The CLASS 1 LASER PRODUCT label is located on the rear
exterior.
VARNING!
Om apparaten används på annat sätt än vad som specificeras i
denna bruksanvising, kan användaren utsättas för osynling
laserstrålning, som överskrider gränsen för laserklass 1.
Precaution to replace Optical block
(SF-P101NR)
Body or clothes electrostatic potential could ruin
laser diode in the optical block. Be sure ground
body and workbench, and use care the clothes
do not touch the diode.
1) After the connection, remove solder shown in
the right figure.
PICK-UP Assy P.C.B
Solder
3
ELECTRICAL MAIN PARTS LIST
REF. NO PART NO. KANRI DESCRIPTION
IC
87-A21-550-010 IC,TA2149N
87-A21-185-040 C-IC,LC72121M
87-A21-064-010 IC,LA4227
87-A21-520-040 C-IC,M61509FP
87-A20-446-010 C-IC,LA9241ML
87-A20-459-010 C-IC,LC78622ED
87-A21-093-010 IC,LA6541D
8A-CH4-661-010 C-IC,LC867132V-5P07
87-A21-431-010 IC,BA4560N
TRANSISTOR
89-327-143-080 TR,2SC2714 (0.1W)
87-026-447-080 TR,2SC1740S R
89-111-624-080 TR,2SA1162Y
87-026-213-080 CHIP-TR,DTC114YK
89-320-011-080 TR,2SC2001 (15W)
89-327-125-080 C-TR,2SC2712(GR)
89-112-965-080 TR,2SA1296 (0.75W)
87-026-463-080 TR,2SA933S (0.3W)
87-026-291-080 TR,DTC124XS
87-A30-226-010 TR,2SB1655E
87-026-462-080 TR,2SC1740 S(RS 0.3W)
89-318-154-080 TR,2SC1815 (0.4W)
89-109-332-380 TR,2SA933RS
89-113-187-080 TR,2SA1318TU
87-026-239-080 TR,DTC114TK (0.2W)
87-026-210-080 C-TR, DTC144EK
87-026-464-080 TR,DTC114TS (0.3W)
DIODE
87-070-345-080 DIODE,IN4148
87-A40-616-070 VARI-CAP,SVC384(S/T)
87-A40-128-080 C-VARI-CAP,HVU202A
87-017-072-080 ZENER,HZS3B1
87-027-399-080 ZENER,HZ7A3L (200MA)<2UW,1US>
87-027-607-080 ZENER,HZ7B3L<1LH>
87-A40-648-080 ZENER,MTZJ8.2A
87-A40-234-080 ZENER,MTZJ5.6A
87-017-978-080 DIODE,1N4003
87-027-702-080 ZENER,HZ6C2L
87-020-465-080 DIODE,1SS133 (110MA)
87-A40-465-010 DIODE,FR202
MAIN C.B
C30 87-010-260-080 CAP, ELECT 47-25V
C251 87-010-401-080 CAP, ELECT 1-50V
C261 87-010-402-080 CAP, ELECT 2.2-50V
C262 87-010-402-080 CAP, ELECT 2.2-50V
C263 87-010-178-080 CHIP CAP 1000P
C264 87-010-178-080 CHIP CAP 1000P
C265 87-010-263-080 CAP, ELECT 100-10V
C266 87-010-263-080 CAP, ELECT 100-10V
C267 87-010-112-080 CAP, ELECT 100-16V
C268 87-010-112-080 CAP, ELECT 100-16V
C271 87-010-221-080 CAP, ELECT 470-10V
C272 87-010-221-080 CAP, ELECT 470-10V
C278 87-010-405-080 CAP, ELECT 10-50V
C279 87-010-385-080 CAP, ELECT 220-25V
C301 87-016-495-000 EL CAP 3300UF/25V
C306 87-010-404-080 CAP, ELECT 4.7-50V
C307 87-010-401-080 CAP, ELECT 1-50V
C308 87-010-221-080 CAP, ELECT 470-10V
C311 87-010-263-080 CAP, ELECT 100-10V
C312 87-010-385-080 CAP, ELECT 220-25V
NO.
C321 87-010-197-080 CAP, CHIP 0.01 DM
C322 87-010-263-080 CAP, ELECT 100-10V
C325 87-010-405-080 CAP, ELECT 10-50V
C401 87-010-403-080 CAP, ELECT 3.3-50V
C402 87-010-197-080 CAP, CHIP 0.01 DM
C403 87-010-263-080 CAP, ELECT 100-10V
C404 87-010-248-080 CAP, ELECT 220-10V
C405 87-010-197-080 CAP, CHIP 0.01 DM
C406 87-010-374-080 CAP, ELECT 47-10V
C407 87-010-178-080 CHIP CAP 1000P
C408 87-010-198-080 CAP, CHIP 0.022
C409 87-010-248-080 CAP, ELECT 220-10V
C410 87-010-263-080 CAP, ELECT 100-10V
C411 87-A11-177-080 C-CAP,S 0.15-16 K B
C412 87-010-401-080 CAP, ELECT 1-50V
C413 87-016-369-080 C-CAP,S 0.033-25 B K
C414 87-010-405-080 CAP, ELECT 10-50V
C416 87-010-545-080 CAP, ELECT 0.22-50V
C417 87-012-157-080 C-CAP,S 330P-50 CH
C418 87-010-213-080 C-CAP,S 0.015-50 B
C419 87-A11-608-080 C-CAP,S 0.33-25 K B
C420 87-016-369-080 C-CAP,S 0.033-25 B K
C421 87-A11-177-080 C-CAP,S 0.15-16 K B
C422 87-010-184-080 CHIP CAPACITOR 3300P(K)
C423 87-010-194-080 C-CAP,S 0.47-25V(Z)F
C424 87-A10-712-080 C-CAP,S 0.22-25V(Z)F
C425 87-010-176-080 C-CAP,S 680P-50 SL
C426 87-A11-608-080 C-CAP,S 0.33-25 K B
C428 87-010-197-080 CAP, CHIP 0.01 DM
C429 87-010-186-080 CAP,CHIP 4700P
C430 87-012-156-080 C-CAP,S 220P-50 CH
C431 87-010-545-080 CAP, ELECT 0.22-50V
C432 87-010-374-080 CAP, ELECT 47-10V
C433 87-010-401-080 CAP, ELECT 1-50V
C434 87-010-184-080 CHIP CAPACITOR 3300P(K)
C435 87-010-197-080 CAP, CHIP 0.01 DM
C436 87-010-374-080 CAP, ELECT 47-10V
C437 87-010-404-080 CAP, ELECT 4.7-50V
C438 87-016-669-080 C-CAP,S 0.1-25 K B
C439 87-010-178-080 CHIP CAP 1000P
C440 87-010-145-080 C-CAP,S 1P-50 CH
C441 87-010-197-080 CAP, CHIP 0.01 DM
C442 87-010-312-080 C-CAP,S 15P-50 CH
C445 87-012-368-080 C-CAP,S 0.1-50 F
C446 87-012-368-080 C-CAP,S 0.1-50 F
C447 87-012-368-080 C-CAP,S 0.1-50 F
C448 87-010-315-080 C-CAP,S 27P-50 CH
C450 87-012-140-080 CAP 470P
C451 87-012-156-080 C-CAP,S 220P-50 CH
C455 87-010-247-080 CAP, ELECT 100-50V
C457 87-010-312-080 C-CAP,S 15P-50 CH
C458 87-010-312-080 C-CAP,S 15P-50 CH
C459 87-010-263-080 CAP, ELECT 100-10V
C460 87-015-819-080 CAPACITOR,0.01
C461 87-010-197-080 CAP, CHIP 0.01 DM
C462 87-010-248-080 CAP, ELECT 220-10V
C463 87-010-197-080 CAP, CHIP 0.01 DM<2UW,1US>
C463 87-010-190-080 S CHIP F 0.01<1LH>
C465 87-010-404-080 CAP, ELECT 4.7-50V
C466 87-012-368-080 C-CAP,S 0.1-50 F
C467 87-010-263-080 CAP, ELECT 100-10V
C469 87-012-154-080 C-CAP,S 150P-50 CH
C470 87-010-544-080 CAP, ELECT 0.1-50V
C471 87-015-785-080 CHIP CAPACITOR, 0.1FZ-25Z
C472 87-015-785-080 CHIP CAPACITOR, 0.1FZ-25Z
C473 87-015-785-080 CHIP CAPACITOR, 0.1FZ-25Z
C474 87-015-785-080 CHIP CAPACITOR, 0.1FZ-25Z
C475 87-010-197-080 CAP, CHIP 0.01 DM
C476 87-010-236-080 CAP,E 1000-10 SME
C477 87-010-197-080 CAP, CHIP 0.01 DM
REF. NO PART NO. KANRI DESCRIPTION
NO.
4
REF. NO PART NO. KANRI DESCRIPTION
C478 87-010-263-080 CAP, ELECT 100-10V
C479 87-010-197-080 CAP, CHIP 0.01 DM
C480 87-010-221-080 CAP, ELECT 470-10V
C481 87-010-405-080 CAP, ELECT 10-50V
C482 87-010-405-080 CAP, ELECT 10-50V
C489 87-012-368-080 C-CAP,S 0.1-50 F
C490 87-012-368-080 C-CAP,S 0.1-50 F
C491 87-010-197-080 CAP, CHIP 0.01 DM
C492 87-010-221-080 CAP, ELECT 470-10V
C494 87-010-197-080 CAP, CHIP 0.01 DM<2UW,1US>
C494 87-010-190-080 S CHIP F 0.01<1LH>
C501 87-012-368-080 C-CAP,S 0.1-50 F
C502 87-010-322-080 C-CAP,S 100P-50 CH
C503 87-010-322-080 C-CAP,S 100P-50 CH
C504 87-010-322-080 C-CAP,S 100P-50 CH
C505 87-010-322-080 C-CAP,S 100P-50 CH
C506 87-010-322-080 C-CAP,S 100P-50 CH
C510 87-016-669-080 C-CAP,S 0.1-25 K B
C831 87-010-198-080 CAP, CHIP 0.022
CN202 8A-CH4-689-010 CONN BASE 3P 2.5mm
CN205 87-A60-109-010 CONN,2P V S2M-2W
CN301 87-099-416-010 CONN,3P EH H WHT
CN401 87-A60-424-010 CONN,16P V TOC-B
CN403 87-099-201-010 CONN,8P 6216 H
CN802 87-049-469-010 CONN,4P V
CNA402 8A-CDB-622-010 CONN ASSY,6P CD-MOTOR
L401 87-003-102-080 COIL, 10UH
L404 87-003-152-080 COIL, 100UH
!
R840 87-029-124-010 RES,FUSE 2.2-1/4
SFR430 87-024-437-080 SFR100K,RH063EC
X401 8Z-CD5-633-010 VIB, CER16.93MHZ FCR16.93M2
TAPE C.B
C211 87-010-805-080 CAP, S 1-16
C212 87-010-805-080 CAP, S 1-16
C215 87-016-460-080 C-CAP,S 0.22-16 B
C216 87-016-460-080 C-CAP,S 0.22-16 B
C231 87-010-213-080 C-CAP,S 0.015-50 B
C232 87-010-213-080 C-CAP,S 0.015-50 B
C233 87-A10-201-080 C-CAP,S0.33-16 KB
C234 87-A10-201-080 C-CAP,S0.33-16 KB
C235 87-016-669-080 C-CAP,S 0.1-25 K B
C236 87-016-669-080 C-CAP,S 0.1-25 K B
C237 87-010-408-080 CAP, ELECT 47-50V
C239 87-010-197-080 CAP, CHIP 0.01 DM
C240 87-010-197-080 CAP, CHIP 0.01 DM
C247 87-010-401-080 CAP, ELECT 1-50V
C248 87-010-401-080 CAP, ELECT 1-50V
C309 87-010-197-080 CAP, CHIP 0.01 DM
C310 87-010-248-080 CAP, ELECT 220-10V
C316 87-010-384-080 CAP, ELECT 100-25V
C483 87-012-156-080 C-CAP,S 220P-50 CH
C484 87-012-156-080 C-CAP,S 220P-50 CH
C801 87-010-248-080 CAP, ELECT 220-10V
C805 87-012-365-080 C-CAP,S 0.027-25VBK
C806 87-012-365-080 C-CAP,S 0.027-25VBK
C807 87-010-405-080 CAP, ELECT 10-50V
C808 87-010-405-080 CAP, ELECT 10-50V
C809 87-010-405-080 CAP, ELECT 10-50V
C810 87-010-405-080 CAP, ELECT 10-50V
C811 87-010-178-080 CHIP CAP 1000P
C812 87-010-178-080 CHIP CAP 1000P
C816 87-010-180-080 C-CER 1500P
C817 87-010-180-080 C-CER 1500P
C819 87-010-426-080 C-CAP,S 0.012-25 B
C820 87-010-426-080 C-CAP,S 0.012-25 B
C821 87-010-401-080 CAP, ELECT 1-50V
C822 87-010-401-080 CAP, ELECT 1-50V
NO.
REF. NO PART NO. KANRI DESCRIPTION
NO.
C823 87-010-178-080 CHIP CAP 1000P
C824 87-010-178-080 CHIP CAP 1000P
C829 87-010-178-080 CHIP CAP 1000P
C830 87-010-178-080 CHIP CAP 1000P
C833 87-018-195-080 CAP, CER 1200P-16V
C834 87-010-248-080 CAP, ELECT 220-10V
C835 87-010-322-080 C-CAP,S 100P-50 CH
C836 87-010-322-080 C-CAP,S 100P-50 CH
C843 87-010-197-080 CAP, CHIP 0.01 DM
C844 87-018-124-080 CAP, CER 270P-50V
C845 87-010-178-080 CHIP CAP 1000P
C846 87-010-263-080 CAP, ELECT 100-10V
C851 87-010-186-080 CAP,CHIP 4700P
C852 87-010-178-080 CHIP CAP 1000P
C853 87-A11-145-080 CAP,TC U 0.01-50 Z F
CN201 87-099-018-010 CONN,16P
CN801 87-A60-110-010 CONN,4P V S2M-4W
CNA302 8A-CDB-627-010 CONN ASSY,6P MA-TUNER
L801 87-007-342-010 COIL,OSC 85K BIAS
SW801 88-CT6-619-010 BACK SLIDE SW 6P2T SHORTIN
FRONT C.B
C601 87-010-313-080 CAP, CHIP 18P
C602 87-010-315-080 C-CAP,S 27P-50 CH
C603 87-010-319-080 C-CAP,S 56P-50 CH
C604 87-010-312-080 C-CAP,S 15P-50 CH
C605 87-010-317-080 C-CAP,S 39P-50 CH
C606 87-015-785-080 CHIP CAPACITOR, 0.1FZ-25Z
C607 87-010-196-080 CHIP CAPACITOR,0.1-25
C608 87-010-196-080 CHIP CAPACITOR,0.1-25
C610 87-010-555-040 CAP,E 100-10 GAS
C611 87-010-196-080 CHIP CAPACITOR,0.1-25
C612 87-A10-189-040 CAP,E 220-10
C613 87-010-495-040 CAP,E 2.2-50 GAS
C614 87-010-196-080 CHIP CAPACITOR,0.1-25
C615 87-010-493-040 CAP,E 0.47-50 GAS
C616 87-010-494-040 CAP,E 1-50 GAS
C620 87-010-555-040 CAP,E 100-10 GAS
C625 87-010-197-080 CAP, CHIP 0.01 DM
C661 87-010-498-040 CAP,E 10-16 GAS
CN601 87-099-033-010 16P 6216 H
CN602 87-099-201-010 CONN,8P 6216 H
CNA603 8A-CHB-616-010 CONN ASSY,4P TU-FR(DIGITAL)
CNA604 8A-CHB-617-010 CONN ASSY,2P VOL-KEY
CNA606 8A-CHB-621-010 CONN ASSY,8P FUNCT-KEY
L601 87-003-171-010 COIL,15UH TROIDAL
LCD601 8A-CHB-625-010 LCD,HLC7107ACH-11
LED602 88-CD6-630-010 LED,934ID RED
LED603 88-CD6-630-010 LED,934ID RED
LED604 88-CD6-630-010 LED,934ID RED
LED608 88-CD6-630-010 LED,934ID RED
S601 8Z-CT6-636-010 SW,TACT EVQJAC04M
S604 8Z-CT6-636-010 SW,TACT EVQJAC04M
S605 8Z-CT6-636-010 SW,TACT EVQJAC04M
S606 8Z-CT6-636-010 SW,TACT EVQJAC04M
S607 8Z-CT6-636-010 SW,TACT EVQJAC04M
X601 87-030-273-010 VIB,XTAL 32.768K5PPM
X602 87-030-376-080 VIB,CER CSA5.76MG200
TU C.B
C1 87-010-314-080 C-CAP,S 22P-50V
C2 87-010-316-080 C-CAP,S 33P-50 CH
C3 87-010-314-080 C-CAP,S 22P-50V
C5 87-016-669-080 C-CAP,S 0.1-25 K B
C6 87-010-313-080 CAP, CHIP 18P
C7 87-014-049-080 CAP,PP 470P-100 J
C8 87-012-349-080 C-CAP,S 1000P-50 CH
C10 87-010-197-080 CAP, CHIP 0.01 DM
5
REF. NO PART NO. KANRI DESCRIPTION
NO.
C11 87-010-197-080 CAP, CHIP 0.01 DM
C12 87-010-197-080 CAP, CHIP 0.01 DM
C13 87-010-150-080 C-CAP,S 6P-50 CH
C14 87-010-303-080 C-CAP,S 330P-50CH
C15 87-012-349-080 C-CAP,S 1000P-50 CH
C16 87-010-374-080 CAP, ELECT 47-10V
C17 87-010-198-080 CAP, CHIP 0.022
C18 87-015-835-080 C-CAP,0.047 D
C19 87-010-263-080 CAP, ELECT 100-10V
C20 87-010-404-080 CAP, ELECT 4.7-50V
C21 87-010-197-080 CAP, CHIP 0.01 DM
C22 87-010-197-080 CAP, CHIP 0.01 DM
C23 87-010-197-080 CAP, CHIP 0.01 DM
C25 87-016-460-080 C-CAP,S 0.22-16 B
C26 87-018-131-080 CAP, CER 1000P-50V
C27 87-A11-067-080 C-CAP,S 1-10 K B
C28 87-016-669-080 C-CAP,S 0.1-25 K B
C29 87-016-669-080 C-CAP,S 0.1-25 K B
C30 87-010-198-080 CAP, CHIP 0.022
C31 87-010-198-080 CAP, CHIP 0.022
C33 87-A11-729-080 C-CAP,0.47-16V Y5V
C34 87-A11-729-080 C-CAP,0.47-16V Y5V
C35 87-015-819-080 CAPACITOR,0.01
C36 87-010-263-080 CAP, ELECT 100-10V
C37 87-010-197-080 CAP, CHIP 0.01 DM
C38 87-010-374-080 CAP, ELECT 47-10V
C39 87-010-404-080 CAP, ELECT 4.7-50V
C40 87-010-197-080 CAP, CHIP 0.01 DM
C41 87-012-349-080 C-CAP,S 1000P-50 CH
C42 87-012-349-080 C-CAP,S 1000P-50 CH
C43 87-012-349-080 C-CAP,S 1000P-50 CH
C44 87-010-311-080 CAP 12P
C45 87-010-312-080 C-CAP,S 15P-50 CH
C46 87-010-197-080 CAP, CHIP 0.01 DM
C47 87-010-197-080 CAP, CHIP 0.01 DM
C48 87-010-197-080 CAP, CHIP 0.01 DM
C49 87-012-140-080 CAP 470P
C50 87-010-197-080 CAP, CHIP 0.01 DM
C71 87-010-197-080 CAP, CHIP 0.01 DM
C72 87-010-263-080 CAP, ELECT 100-10V
C73 87-010-197-080 CAP, CHIP 0.01 DM
C75 87-010-197-080 CAP, CHIP 0.01 DM
C91 87-010-197-080 CAP, CHIP 0.01 DM
C92 87-010-197-080 CAP, CHIP 0.01 DM
C93 87-010-197-080 CAP, CHIP 0.01 DM
CF1 87-A91-094-010 FLTR,CDA10.7 MG80A
CF2 82-785-747-080 CF,MS2 GHY,R
CF3 82-785-747-080 CF,MS2 GHY,R
CN2 87-099-194-010 CONN,6P 6216V
CN3 87-A60-110-010 CONN BASE 4P
REF. NO PART NO. KANRI DESCRIPTION
HLD1 88-CD6-661-010 HLDR,BAR ANT.
HLD2 88-CD6-661-010 HLDR,BAR ANT.
L2 87-A50-560-010 COIL,FM BPF(ACD)
L3 8A-CH4-670-010 BAR-ANT,MW 2B-ACH(COI)
L4 87-A50-420-010 COIL,MW OSC(SYN)
L5 87-A50-566-010 COIL,FM RF EX(ACH)
L6 87-A50-568-010 COIL,FM OSC EX(ACH)
L7 87-A91-308-010 FLTR,PCFAZH- 450T (TOK)
L8 87-005-849-080 COIL,10UH(CECS)
TC1 87-011-254-080 TRIMER,20P LAR
X1 87-A70-061-010 VIB,XTAL 4.500MHZ CSA-309
HP C.B
CN203 87-049-469-010 CONN,4P V
J251 87-009-216-010 JACK, DIA 3.5
LED C.B
CN607 87-009-236-010 CONN 8P PH H
LED605 88-CD6-630-010 LED,934ID RED
LED606 88-CD6-630-010 LED,934ID RED
LED611 88-CD6-631-010 LED,934GD GRN
S608 8Z-CT6-636-010 SW,TACT EVQJAC04M
S609 8Z-CT6-636-010 SW,TACT EVQJAC04M
S610 8Z-CT6-636-010 SW,TACT EVQJAC04M
S611 8Z-CT6-636-010 SW,TACT EVQJAC04M
S613 8Z-CT6-636-010 SW,TACT EVQJAC04M
VOL C.B
CN608 84-722-632-010 CONN,2P H
S614 8Z-CT6-636-010 SW,TACT EVQJAC04M
S615 8Z-CT6-636-010 SW,TACT EVQJAC04M
PWR C.B
C901 87-018-205-080 CAP, CERA-SOL 0.022
C902 87-018-205-080 CAP, CERA-SOL 0.022
C903 87-018-205-080 CAP, CERA-SOL 0.022
C904 87-018-205-080 CAP, CERA-SOL 0.022
CNA901 8A-CDB-621-010 CONN ASSY,3P POWER
!
PR901 87-A90-092-080 PROTECTOR,2.5A 491
MOTOR C.B
M2 9X-262-576-910 MOTOR GEAR ASSY
PIN3 91-564-722-110 CONNECTOR 6P
SW1 91-572-085-120 LEAF SW
BATT C.B
NO.
• Regarding connectors, they are not stocked as they are not the initial order items.
The connectors are available after they are supplied from connector manufacturers upon the order is received.
6
CHIP RESISTOR PART CODE
Chip Resistor Part Coding
88
LCD DISPLAY
LCD, HLC7107ACH-11
A
Resistor Code
Chip resistor
Wattage Type Tolerance
1/16W 1005 5% CJ
1/16W
1/10W
1/8W
1608
2125
3216
5%
5%
5%
TRANSISTOR ILLUSTRATION
Symbol
CJ
CJ
CJ
Figure
Value of resistor
Form
L
Dimensions (mm)
t
W
0.55
Resistor Code
108
118
128
LW t
1.0 0.5 0.35 104
1.6 0.8 0.45
2 1.25 0.45
3.2
1.6
: A
: A
ECB
2SB1655E
C
B
ECB ECB
DTC114TS
E
2SA1162Y
2SC2712
2SC2714
DTC114TK
DTC114YK
DTC144EK
2SA933RS
2SC1740S R
DTC124XS
ECB
2SA933S
2SA1296
2SA1318TU
2SC1740 S
2SC1815
2SC2001
87
WIRING-1 (MAIN/TAPE)
1
A
234567
8
9
10
11 12 13
M
OTOR C.B
M2
14
B
_
C
D
E
F
+
SW1
PIN3
M2
(SLED MOTOR)
SW1
(INSIDE LIMIT SW)
(SPINDLE MOTOR)
_
M3
M3
+
G
H
I
J
K
109
SCHEMATIC DIAGRAM-1 (MAIN)
1211
SCHEMATIC DIAGRAM-2 (CD)
1413
WIRING-2 (POWER)
1
A
B
C
D
234567
E
F
G
H
I
J
K
15
WIRING-3 (TU)
1
A
B
C
D
234567
E
F
G
H
I
J
K
16
SCHEMATIC DIAGRAM-3 (TUNER)
VT
TU C.B
1817
WIRING-4 (FRONT)
1
A
B
C
D
234567
8
9
10
11 12 13
14
E
F
G
H
I
J
K
2019
SCHEMATIC DIAGRAM-4 (FRONT)
2221
ELECTRICAL ADJUSTMENT
L003
(BAR-ANT)
< TUNER SECTION >
1. AM IF Adjustment
L007 ....................................................................... 450kHz
5
13
TU C.B
TAPE C.B
3
L007
IC001
L005
L006
C39
+
24
L004
TC001
3
2
4
HP C.B
J251
78
2. AM VT Adjustment
Settings: • Test point: C39+
• Adjustment location: L004
Method: Set to AM 1000kHz adjust L004 so that the test
point becomes 3.7V±0.02V
3. AM Tracking Adjustment
L003 ....................................................................... 600kHz
TC001, L007 ........................................................ 1400kHz
4. FM VT Adjustment
Settings: • Test point: C39+
• Adjustment location: L006
Method: Set to FM 108MHz adjust L006 so that the test
point becomes 6.0V±0.2V
5. FM Tracking Adjustment
L005 ........................................................................98MHz
< TAPE SECTION >
6. Bias frequency Adjustment
L801 ............................................................. 85Hz ±500Hz
7. Tape speed Adjustment
Settings: • Test tape: TTA-100
• Test point: PHONES JACK (J251)
• Adjustment location: SFR of deck motor
Method: Play back the test tape and adjust so that the
output frequency is 3000Hz ±30Hz.
8. Azimuth Adjustment
Settings: • Test tape: TTA-320
• Test point: PHONES JACK (J251)
• Adjustment location:Azimuth adjustment
screw
Method: Play back the test tape and adjust so that the
output is maximum.
8
L801
6
M1
(DECK MOTOR)
7
2423
IC BLOCK DIAGRAM
IC, TA2149N
IC, LC72121M
25
IC, M61509FP
INA1
INB1
INC1
IND1
INE1
QF1
QF2
TONEH1
TONEL1
OUT1
GND
VDD
10
11
1
2
3
4
5
6
7
8
9
VOL VOL
Treble
boost
ATT ATT
Bass
boost
Mono.SW
MUTE
Treble
boost
Bass
boost
Control logic
24
23
22
21
20
19
18
17
16
15
14
1312
INA2
INB2
INC2
IND2
INE2
QF4
QF3
TONEH2
TONEL2
OUT2
VSS
CONT
IC, LA4227
26
IC, LA6541D
IC, BA4560N
27
IC DESCRIPTION
IC, LA9241ML
Pin No. Pin Name I/O Description
1
2
FIN2
FIN1
Pin to which external pickup photo diode is connected. RF signal is created by adding
I
with the FIN1 pin signal. FE signal is created by subtracting from the FIN1 pin signal.
I
Pin to which external pickup photo diode is connected.
10
11
12
13
14
15
16
17
3
4
5
6
7
8
9
E
F
TB
TE–
TE
TESI
SCI
TH
TA
TD–
TD
JP
TO
FD
FD–
Pin to which external pickup photo diode is connected. TE signal is created by
I
subtracting from the F pin signal.
I
Pin to which external pickup photo diode is connected.
I
DC component of the TE signal is input.
I
Pin to which external resistor setting the TE signal gain is connected between the TE pin.
O
TE signal output pin.
TES “Track Error Sense” comparator input pin. TE signal is passed through a band-
I
pass filter then input.
I
Shock detection signal input pin.
I
Tracking gain time constant setting pin.
O
TA amplifier output pin.
Pin to which external tracking phase compensation constants are connected between
I
the TD and VR pins.
I
Tracking phase compensation setting pin.
I
Tracking jump signal (kick pulse) amplitude setting pin.
O
Tracking control signal output pin.
O
Focusing control signal output pin.
Pin to which external focusing phase compensation constants are connected between
I
the FD and FA pins.
18
19
20
21
22
23
24
25
26
27
28
29
30, 31
32, 33
34
FA
FA–
FE
FE–
AGND
SP
SPI
SPG
SP–
SPD
SLEQ
SLD
SL–, SL+
JP–, JP+
TGL
—
—
Pin to which external focusing phase compensation constants are connected between
I
the FD– and FA– pins.
Pin to which external focusing phase compensation constants are connected between
I
the FA and FE pins.
O
FE signal output pin.
I
Pin to which external FE signal gain setting resistor is connected between the FE pin.
Analog signal GND.
No connection.
O
Single ended output of the CV+ and CV– pin input signal.
I
Pin to which external spindle gain setting resistor in 12 cm mode is connected.
Pin to which external spindle phase compensation constants are connected together
I
with SPD pin.
O
Spindle control signal output pin.
I
Pin to which external sled phase compensation constants are connected.
O
Sled control signal output pin.
I
Sled advance signal input pin from microprocessor.
I
Tracking jump signal input pin from DSP.
I
Tracking gain control signal input from DSP. Low gain when TGL = H.
35
TOFF
I
Tracking off control signal input pin from DSP. Off when TOFF = H.
28
Pin No. Pin Name I/O Description
36
TES
O
Pin from which TES signal is output to DSP.
37
38
39, 40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
HFL
SLOF
CV–, CV+
RFSM
RFS–
SLC
SLI
DGND
FSC
TBC
NC
DEF
CLK
CL
DAT
CE
DRF
—
—
“High Frequency Level” is used to judge whether the main beam position is on top of
O
bit or on top of mirror.
I
Sled servo off control input pin.
I
CLV error signal input pin from DSP.
O
RF output pin.
RF gain setting and EFM signal 3T compensation constant setting pin together with
I
RFSM pin.
“Slice Level Control” is the output pin which controls the RF signal data slice level by
O
DSP.
I
Input pin which control the data slice level by the DSP.
Digital system GND.
O
Output pin to which external focus search smoothing capacitor is connected.
I
“Tracking Balance Control” EF balance variable range setting pin.
No connection.
O
Disc defect detector output pin.
I
Reference clock input pin. 4.23 MHz of the DSP is input.
I
Microprocessor command clock input pin.
I
Microprocessor command data input pin.
I
Microprocessor command chip enable input pin.
O
“Detect RF” RF level detector output.
55
56
57
58
59
60
61
62
63
64
FSS
VCC2
REFI
VR
LF2
PH1
BH1
LDD
LDS
VCC1
—
—
—
I
“Focus Search Select” focus search mode (± search/+ search) select pin.
Servo system and digital system Vcc pin.
Pin to which external bypass capacitor for reference voltage is connected.
O
Reference voltage output pin.
I
Disc defect detector time constant setting pin.
I
Pin to which external capacitor for RF signal peak holding is connected.
I
Pin to which external capacitor for RF signal bottom holding is connected.
O
APC circuit output pin.
I
APC circuit input pin.
RF system Vcc pin.
29
IC, LC78622ED
Pin No. Pin Name I/O Description
1
2
3
DEFI
TAI
PDO
I
Defect sense signal (DEF) input pin. (Connect to 0V when not used).
I
O
Test signal input pin with built-in pull-down resistor. Be sure to connect to 0V.
Phase comparator output pin to control external VCO.
4
5
6
7
8
9
10
11
12, 13
14
15
16
17
18
19, 20
21
VVSS
ISET
VVDD
FR
VSS
EFMO
EFMIN
T2
CLV+, CLK-
___
V/P
HFL
TES
TOFF
TGL
JP+, JP-
PCK
—
—
—
For PLL.
I
GND pin for built-in VCO. Be sure to connect to 0V.
Pin to which external resistor adjusting the PD0 output current.
Power supply pin for built-in VCO.
I
Pin for VCO frequency range adjustment.
Digital system GND. Be sure to connect to 0V.
O
EFM signal output pin.
For slice level control.
I
I
Test signal input pin with built-in pull-down resistor. Be sure to connect to 0V.
O
Disc motor control output. Three level output is possible using command.
EFM signal input pin.
Rough servo or phase control automatic selection monitoring output pin. Rough servo
O
at H. Phase servo at L.
I
Track detect signal input pin. Schmidt input.
I
Tracking error signal input pin. Schmidt input.
O
Tracking OFF output pin.
O
Tracking gain selection output pin. Gain boost at L.
O
Track jump control signal output pin. Three level output is possible using command.
O
EFM data playback clock monitoring pin 4.3218 MHz when phase is locked in.
22
23
24
25
26
27
28
29
30
31
32, 33
34
35
36
37
38
39
40
41
42
FSEQ
VDD
SL+
SL-
—
PUIN
RW
EMPH
C2F
DOUT
T3, T4
N.C.
MUTEL
LVDD
LCHO
LVSS
RVSS
RCHO
RVDD
MUTER
—
—
—
—
—
—
—
Sync signal detection output pin. H when the sync signal which is detected from EFM
O
signal and thesync signal which is internally generated agree.
Digital system power supply pin.
O
Moves the sled to outer circumference.
O
Moves the sled to inner circumference.
Not connected.
I
CD pickup inner switch detection.
O
Read, wright signal.
O
De-emphasis monitor output pin. De-emphasis disc is being played back at H.
O
C2 flag output pin.
O
DIGITAL OUT output pin. (EIAJ format).
I
Test signal input pin with built-in pull-down resistor. Be sure to connect to 0V.
Not used. Set the pin to open.
O
L-channel 1-bit DAC.
O
L-channel mute output pin.
L-channel power supply pin.
L-channel output pin.
L-channel GND. Be sure to connect to 0V.
R-channel GND. Be sure to connect to 0V.
O
R-channel 1-bit DAC.
R-channel output pin.
R-channel power supply pin.
O
R-channel mute output pin.
30
Pin No. Pin Name I/O Description
43
44
XVDD
XOUT
—
Crystal oscillator power supply pin.
O
Pin to which external 16.9344 MHz crystal oscillator is connected.
45
XIN
I
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
XVSS
SBSY
EFLG
PW
SFSY
SBCK
FSX
WRQ
RWC
SQOUT
COIN
___________
CQCK
RES
T11
16M
4.2M
T5
______
CS
T1
—
Crystal oscillator GND pin. Be sure to connect to 0V.
O
Subcode block sync signal output pin.
O
C1, C2, single and dual correction monitoring pin.
O
Subcode P, Q, R, S, T, U and W output pin.
O
Subcode frame sync signal output pin. Falls down when subcode enters standby.
Subcode read clock input pin. Schmidt input. (Be sure to connected to 0V when not
I
in use.)
Pin outputting the 7.35 kHz sync signal which is generated by dividing frequency of
O
crystal oscillator.
O
Subcode Q output standby output pin.
I
Read/write control input pin. Schmidt input.
O
Subcode Q output pin.
I
Command input pin from microprocessor.
I
Command input read clock or subcode read input clock from SQOUT pin
I
LC78622 reset input pin. Set this pin to L once when the main power is turned on.
O
Test signal output pin. Use this pin as open (normally L output).
O
16.9344 MHz output pin.
O
4.2336 MHz output pin.
I
Test signal input pin with built-in pull-down resistor. Be sure to connect to 0V.
Chip select signal input pin with built-in pull-down resistor. Be sure to connect to 0V
I
while it is not controlling.
I
Test signal input pin without built-in pull-down resistor. Be sure to connect to 0V.
31
IC, LC867132V-5P07
Pin No. Pin Name I/O Description
O
1
2
3
O-RMC/CE
O-DATA
O-CLK
CD read/write control output.
O
Data output to sound processor IC (M62495FP).
O
Clock output to sound processor IC (M62495FP).
10
11
12
13
14
15
16
17
18
19
20
21
22
4
5
6
7
8
9
NC
O-CLK SFT
I-HOLD
I-RST
XT1 (IN)
XT2 (OUT)
VSS1
CF1 (IN)
CF2 (OUT)
VDD1
I-FM ST
I-KEYO
I-CD SW
I-KEY1
I-MOTOR
I-REC
I-FM/AM (NC)
I-TU DO
O-BASS LED (NC)
—
—
—
Not Connected.
O
Clock shift output of the microcomputer.
I
Hold status detection.
I
Microcomputer reset.
I
Connected to 32.768kHz crystal oscillator.
O
GND.
I
Connected to 5.76MHz Ceramic Filter.
O
Power supply for microcomputer (+5V).
I
FM STEREO status input.
I
KEY AD input.
I
CD DOOR SW status detection input.
I
KEY AD input.
I
DECK MECHA MOTOR status input.
I
REC status input.
I
FM, AM status input. (Not connected)
I
Data input from tuner PLL.
O
BASS LED ON/OFF control output. (Not connected)
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37-40
41
42
43-50
O-QS LED
NC
O-INT
I-DRF
I-WRQ
I-REMO
SO/PAO (NC)
S1/PA1 (NC)
S2/PA2
S3/PA3 (NC)
S4/PA4 (NC)
S5/PA5 (NC)
S6/PA6
S7/PA7
S8-S11
VDD3
VSS3
S12-S19
—
—
—
O
Q-Sound LED ON/OFF control output.
Not connected.
O
INT DIODE MATRIX detection output.
I
CD RF level detection input.
I
CD sub-code Q standby input.
I
Remote control input.
O
LCD segment output and initial settings output. (SW) (Not connected)
O
LCD segment output and initial settings output. (LW) (Not connected)
O
LCD segment output and initial settings output. (MW 10K)
O
LCD segment output and initial settings output. (FM WIDE) (Not connected)
O
LCD segment output and initial settings output. (OIRT) (Not connected)
O
LCD segment output and initial settings output. (SW2) (Not connected)
O
LCD segment output and initial settings output. (SYN)
O
LCD segment output and initial settings output.
O
Power supply for microcomputer (+5V).
GND.
O
LCD segment output.
51-54
S20-S23 (NC)
O
LCD segment output. (Not Connected)
32
Pin No. Pin Name I/O Description
55
56
57
O-CD LED
O-TU LED
O-TA LED (NC)
LED ON/OFF control output for CD functions.
O
LED ON/OFF control output for TU functions.
O
LED ON/OFF control output for TAPE functions. (Not Connected)
O
58
59
60
61
62
63
64-66
67
68
69
70
71
72
73
74
75
76
77
78
O-ROCK LED
O-POP LED
O-JAZZ LED
NC
I-CD TEST (NC)
I-TU TEST (NC)
COM0-COM2
NC
VSS2
VDD2
O-CD ON
O-TU ON
O-P.CONT
NC
O-MUTE
O-FM MONO (NC)
O-BEAT CONT
O-QSOUND
O-COIN
—
—
—
—
—
LED ON/OFF control output for ROCK.
O
LED ON/OFF control output for POP.
O
LED ON/OFF control output for JAZZ.
O
I
Not connected.
I
LCD common output.
O
Not connected.
GND.
Power supply for microcomputer (+5V).
CD PWR control output.
O
TU PWR control output.
O
Power supply control output.
O
Not connected
Main mute output.
O
FM force control MONO output. (Not connected)
O
BEAT switch over output.
O
Q-Sound ON/OFF output.
O
CD command output.
O
79
80
I-SQOUT
O-CQCK
CD sub-code Q input.
I
CLK for CD commands/sub-codes.
O
33
MECHANICAL PARTS LIST 1/1
REF. NO PART NO. KANRI DESCRIPTION
NO.
1 8A-CDB-006-010 WINDOW,CASS
2 8A-CDB-008-010 BOX,CASS
3 8A-CDB-204-010 SPR-T,CASS
4 8A-CDB-001-010 CABI,FR
5 88-CD8-622-010 SPKR,F 77 7OHM 3W
6 8Z-CDB-208-010 HLDR,SPKR
7 8A-CDB-205-010 PLATE,OIL DUMP
8 87-063-164-010 OIL-DMPR 80
9 8A-CDB-206-010 BASE,CD
10 8A-CDB-016-010 BTN,CD
11 8A-CHB-013-010 WINDOW,DISPLAY<1LH>
11 8A-CHB-002-010 WINDOW,DISPLAY<2UW,1US>
12 8A-CDB-023-010 GRILLE,SPKR
13 8Z-CT6-213-010 BASE,CHUCK
14 8Z-CT6-214-010 RING,CHUCK
15 87-036-368-010 MAGNET
16 86-CT9-222-010 PLATE,MAGNET
17 86-CT9-217-010 HLDR,CHUCK A(S)
18 8A-CDB-009-010 BOX,CD
19 8A-CHB-011-010 WINDOW,CD
20 8A-CHB-014-010 BTN,FUNC
21 8A-CDB-213-010 BASE,FUNC
22 8A-CDB-014-010 BTN,QSOUND
23 8A-CDB-003-010 CHAS,CD
24 8A-CDB-021-010 LENS,FUNC
25 8A-CDB-203-010 HLDR,LED FUNC
26 88-CH6-220-010 CUSHION,CD A
27 8Z-CT9-064-010 PANEL CD
28 87-036-389-010 SW,PUSH LOCK
29 8A-CDB-218-010 SPR-T,CD
30 8A-CDB-620-010 CONN ASSY,2P CD-DOOR
31 M8-ZZK-E90-070 DA11T3C
32 87-063-165-010 OIL-DMPR 150
33 8A-CDB-214-010 BASE,VOL
34 8A-CDB-012-010 BTN,VOL
REF. NO PART NO. KANRI DESCRIPTION
35 8A-CHB-202-010 HLDR,LCD
36 8A-CDB-212-010 PLATE,REC
37 8A-CHB-619-010 FF-CABLE, 8P 1.25 CD-FR
38 8A-CHB-618-010 FF-CABLE, 16P 1.25 FR-MAIN
39 8A-CDB-219-010 HLDR,TRAN
!
40 8A-CDB-651-010 PT,H 2.5W EI48X23<1LH>
!
40 8A-CDB-650-010 PT,U 2.5W EI48X23<2UW,1US>
41 8A-CDB-019-010 HANDL,GRIP
42 8A-CDB-018-010 COVER, HANDL
43 8Z-CH4-640-010 ANT,ROD
44 8A-CHB-001-010 CABI,REAR
45 87-A91-369-010 SW,AC SL 2 2 2 SDKGA41700<1LH>
46 8A-CDB-623-010 FF-CABLE, 16P 1.0 CD-RF
47 8A-CDB-020-010 LID,BATT
48 86-CT9-223-010 CUSH,FOOT
49 8A-CDB-207-010 HLDR,ANT
!
50 87-A60-178-010 JACK,AC E W/SW<1LH>
!
50 87-A60-177-010 JACK,AC U W/SW<2UW,1US>
51 8A-CDB-215-010 SPR-T,BATT
52 8A-CDB-220-010 HLDR,M66 BAR ANT
53 8A-CDB-015-010 KEY,CASS
54 8A-CDB-216-010 PLATE,TRAN
55 87-A90-086-010 COVER,AC-SOCKET
56 8A-CDB-626-010 CONN ASSY,4P CASS HEAD
57 8A-CDB-633-010 CONN ASSY,4P SPKR
58 8A-CDB-625-010 CONN ASSY,4P CASS MECHA
A 81-CD5-204-010 SCREW CD
B 87-651-104-410 VT1+3-30
C 87-741-096-410 UT2+3-10
D 87-751-097-410 SCREW 3X12
E 87-261-096-410 SCREW,V+3-10 GLD
F 87-741-074-410 UT2+2.6-8
G 87-261-032-410 SCREW,V+2-3 GLD
H 87-751-095-410 VT2+3-8 W/O
NO.
COLOR NAME TABLE
Basic color symbol Color Basic color symbol Color Basic color symbol Color
B Black C Cream D Orange
G Green H Gray L Blue
LT Transparent Blue N Gold P Pink
R Red S Silver ST Titan Silver
T Brown V Violet W White
WT Transparent White Y Yellow YT Transparent Yellow
LM Metallic Blue LL Light Blue GT Transparent Green
LD Dark Blue DT Transparent Orange
34
MECHANICAL EXPLODED VIEW 1/1
19
23
P.C .B
H
28
C
29
H
H
H
41
42
14
13
17
16
15
5
20
P.C .B
18
47
43
B
B
D
E
44
H
52
25
57
24
26
P.C .B
10
27
24
31
32
7
D
A
A
26
LCD
H
9
10
A
38
35
10
26
A
H
D
P.C .B
9
8
22
21
25
C
H
C
6
6
C
34
33
D
46
37
CHASS,TU
BAR-ANT
P.C .B
D
54
39
P.C .B
40
55
F
E
50
F
45
51
30
P.C .B
58
H
D
49
48
P.C .B
53
H
56
H
D
D
G
D
36
D
TN-21ZVC-2000
11
2
1
3
12
4
7
6
C
C
C
6
5
3635
TAPE MECHANISM EXPLODED VIEW 1/1
F
G
1
E
2
8
10
J
L
14
b
18
19
7
36
46
47
25
9
21
20
22
23
24
c
51
26
27
28
A
6
29
LUG PLATE
52
4
3
a
15
16
17
34
35
c
C
37
11
5
12
13
49
48
TAPE MECHANISM PARTS LIST 1/1
REF. NO PART NO. KANRI DESCRIPTION
1 S1-921-030-4A0 HEAD BASE
2 S1-821-030-070 AZIMUTH SPRING
3 S1-921-030-090 PANEL P SPRING
4 S1-921-260-050 GEAR PLATE SPRING
5 S1-921-265-020 GEAR PLATE ASSY
6 S1-510-020-020 REC SPRING PLATE
7 S1-921-015-010 CHASSIS ASSY
8 S1-921-030-110 HEAD PANEL
9 S1-921-143-160 BASE ASSY
10 S1-921-141-8A0 M CONTROL SPRING
11 S1-921-260-4A0 SENSING LEVER
12 S1-921-043-100 PINCH ROLLER ARM ASSY
13 S1-921-130-010 EJECT SLIDE LEVER
14 S1-921-141-3A0 P CONTROL SPRING
15 S1-921-140-550 PAUSE LEVER(E)
16 S1-921-140-120 PAUSE LEVER SPRING
17 S1-921-140-110 PAUSE STOPPER
18 S1-921-140-150 BUTTON LEVER SPRING(B)
19 S1-821-011-590 E KICK LEVER
20 S1-921-141-070 BUTTON LEVER SPRING(A)
21 S6-401-011-490 LEAF SW MSW-1541T
22 S1-921-140-090 SWITCH ACTUATOR
23 S1-921-140-080 PUSH BUTTON ACTUATOR
24 S1-921-140-190 PLAY BUTTON LEVER
25 S1-921-030-100 MG ARM SPRING
31
30
b
32
33
A
26 S1-921-140-040 REW BUTTON LEVER
27 S1-921-140-050 FF,BUTTON REVER
28 S1-921-140-060 STOP BUTTON LEVER
29 S1-921-140-600 PAUSE BUTTON LEVER
30 S1-821-100-700 FF GEAR
31 S1-921-050-060 SENSER
32 S1-921-053-100 TAKE UP REEL ASSY
33 S1-829-100-010 PACK SPRING
34 S1-921-050-150 S REEL HUB
35 S1-921-050-220 BACK TENSION SPRING
NO.
a
C
REF. NO PART NO. KANRI DESCRIPTION
NO.
36 S1-921-140-030 REC BUTTON LEVER
37 S1-921-140-170 P.S.LEVER SPRING
38 S1-921-073-040 RF CLUTCH ASSY
39 S1-921-070-030 RF BELT
40 S1-921-260-020 CAM GEAR
41 S1-921-140-160 E ACTUATOR SPRING
42 S1-921-093-210 FLYWHEEL ASSY
43 S1-921-090-380 MAIN BELT
44 S1-921-120-590 MOTOR PULLEY
45 S6-002-030-220 MOTOR EG530AD-2B
46 S6-209-100-100 E HEAD PH-K380-MS1
47 S1-921-030-050 MG ARM
48 S1-921-140-210 REC BUTTON LEVER SPRING
49 S1-821-100-690 RECORD SAFETY LEVER
50 S1-821-128-9A0 MOTOR BRACKET
51 S1-821-010-500 PLAY BUTTON LEVER SPRING
52 S6-201-011-110 HEAD,RP7442ES-0951
A S9-P04-200-310 C TAPPING SCREW 2-3
B S1-921-120-020 MOTOR COLLER SCREW
C S9-B10-200-510 P TAPPING BIND SCREW M2-5
D S9-C07-204-510 SCREW,TAPPING(CAMERA)M2-4.5
E S9-P01-200-610 SCREW,M2-6
F S9-B01-200-310 (+)BIND SCREW M2-3
G S9-F08-200-710 AZIMUTH SCREW M2-7
H S1-921-120-030 MB SCREW
I S9-W02-300-100 P WASHER CUT 1.2-3.8-0.3
J S9-W02-500-100 P WASHER CUT 1.45-3.8-0.5
K S9-W01-400-100 P WASHER 2-3.5-0.4
L S9-W01-130-200 P WASHER 2.1-4-0.13
38
39
42
43
D
40
D
K
41
I
B
B
50
H
44
45
3837
CD MECHANISM EXPLODED VIEW 1/1
SHAFT,SLIDE
B
SF-P101NR
CHASSIS
B
1
2
A
A
3
SPINDLE
MOTOR(M3)
CD MECHANISM PARTS LIST 1/1
REF. NO PART NO. KANRI DESCRIPTION
NO.
1 S2-121-A28-400 COVER GEAR
2 S2-511-A21-000 GEAR MIDDLE
3 S2-511-A21-100 GEAR,DRIVE
A S1-PN2-03R-OSE SCR PAN PCS 2-3
B 87-261-073-410 SCR S-TPG FLT 2.6-6
ALL M8-ZZK-E90-070 DA11T3C
MOTOR C,B
39
2–11, IKENOHATA 1–CHOME, TAITO-KU, TOKYO 110, JAPAN TEL:03 (3827) 3111
737004
Printed in Singapore
Loading...