CSD-TD24
EZ,K
CSD-TD26
CSD-TD27
CSD-TD28
U
U
U
SERVICE MANUAL
COMPACT DISC STEREO
RADIO CASSETTE RECORDER
• This Service Manual is the “Revision Publishing” and replaces “Simple Manual”
CSD-TD26/TD27/TD28 <U>, (S/M Code No. 09-011-443-0T1) and
CSD-TD24 <EZ,K>, (S/M Code No. 09-012-443-0T2).
BASIC TAPE MECHANISM: ZZM-1 AR5NC
BASIC CD MECHANISM: DA11T3C
S/M Code No. 09-013-443-0R1
REVISION
DATA
SPECIFICATIONS
<Tuner section>
Frequency range
FM 87.5 - 108.0 MHz
Antenna: Rod antenna
AM<U> 530/531 - 1,710/1,602 kHz,
(10/9 kHz step)
Antenna: Ferrite bar antenna
MW<EZ,K> 531/530 - 1,602/1710 kHz,
(9/10 kHz step)
Antenna: Ferrite bar antenna
LW<EZ,K> 153 - 288 kHz
Antenna: Ferrite bar antenna
<Deck section>
Track format 4 tracks, 2 channels
Frequency range Normal tape: 50 - 12,500 Hz (EIAJ)
Recording system AC bias
Erasing system Magnet erase
Heads Recording/playback head (1)
Erasure head (1)
<CD player section>
Disc Compact disc
Scanning method Non-contact optical scanner
(semiconductor laser)
<General>
Speaker 100 mm cone type (2)
Output Headphones jack(stereo mini-jack)
Power output U:
2.5 W + 2.5 W
(EIAJ 7 ohms, T.H.D. 10 % DC)
EZ:
2.9 W + 2.9 W (DIN MUSIC POWER)
2.5 W + 2.5 W
(EIAJ 7 ohms, T.H.D. 10 % DC)
1.9 W + 1.9 W (DIN 1 %, Rated Power)
K:
2.5 W + 2.5 W
(EIAJ 7 ohms, T.H.D. 10 % DC)
1.9 W + 1.9 W (DIN 1 %, Rated Power)
Power requirements DC 12 V using eight size C (R14)
batteries
U: AC 120 V, 60 Hz
EZ,K: AC 230 V, 50 Hz
Power consumption 15 W
Dimensions (W x H x D) 414 x 183 x 235 mm (16 3/8 x 71/4 x 93/8 in.)
Weight 3.2 kg (7 lbs.1 oz.)
(excluding batteries)
• Design and specifications are subject to change without notice.
ACCESSORIES / PACKAGE LIST
PART NO.
1 8B-CHA-903-010 IB,U(ESF)FM<U>
1 8B-CHA-906-010 IB,EZ(9L)FM<EZ>
1 8B-CHA-905-010 IB,K(E)FM<K>
!
2 87-A80-109-010 AC CORD,HK7281 BLK U<U>
!
2 87-A80-081-010 AC CORD SET ASSY,EZ BLK<EZ,K>
NO.
DESCRIPTION REF. NO. KANRI
– 2 –
PROTECTION OF EYES FROM LASER BEAM DURING SERVICING
This set employs laser. Therefore, be sure to follow carefully
the instructions below when servicing.
WARNING!!
WHEN SERVICING, DO NOT APPROACH THE LASER
EXIT WITH THE EYE TOO CLOSELY. IN CASE IT IS
NECESSARY TO CONFIRM LASER BEAM EMISSION.
BE SURE TO OBSERVE FROM A DISTANCE OF MORE
THAN 30cm FROM THE SURFACE OF THE OBJECTIVE LENS ON THE OPTICAL PICK-UP BLOCK.
s Caution: Invisible laser radiation when
open and interlocks defeated avoid
exposure to beam.
s Advarsel: Usynlig laserståling ved åbning,
når sikkerhedsafbrydere er ude af funktion.
Undgå udsættelse for stråling.
VAROITUS!
Laiteen Käyttäminen muulla kuin tässä käyttöohjeessa
mainitulla tavalla saataa altistaa käyt-täjän
turvallisuusluokan 1 ylittävälle näkymättömälle
lasersäteilylle.
VARNING!
Om apparaten används på annat sätt än vad som
specificeras i denna bruksanvising, kan användaren
utsättas för osynling laserstrålning, som överskrider
gränsen för laserklass 1.
CAUTION
Use of controls or adjustments or performance of procedures other than those specified herin may result in
hazardous radiation exposure.
ATTENTION
L’utillisation de commandes, réglages ou procédures
autres que ceux spécifiés peut entraîner une dangereuse
exposition aux radiations.
ADVARSEL
Usynlig laserståling ved åbning, når sikkerhedsafbrydereer
ude af funktion. Undgå udsættelse for stråling.
This Compact Disc player is classified as a CLASS 1
LASER product.
The CLASS 1 LASER PRODUCT label is located on the
rear exterior.
CLASS 1 LASER PRODUCT
KLASSE 1 LASER PRODUKT
LUOKAN 1 LASER LAITE
KLASS 1 LASER APPARAT
Precaution to replace Optical block
(SF-P101NR)
Body or clothes electrostatic potential could ruin
laser diode in the optical block. Be sure ground
body and workbench, and use care the clothes
do not touch the diode.
1) After the connection, remove solder shown in
the right figure.
PICK-UP Assy PWB
– 3 –
ELETRICAL MAIN PARTS LIST
REF. NO. DESCRIPTION PART NO.
NO.
IC
87-A21-928-010 IC,LC72131D-N
87-A21-193-010 IC,TA8227P
87-A21-520-040 C-IC,M61509FP<U>
87-A21-443-040 C-IC,M62495AFP<EZ,K>
87-A20-446-010 C-IC,LA9241ML
87-A21-319-010 C-IC,LC78622NE
87-A21-891-010 C-IC,MM1469XH
8B-CHA-600-010 C-IC,LC867132V-5T67
87-A21-550-010 IC,TA2149N
87-A21-607-010 IC,NJM14558LD
TRANSISTOR
87-026-447-080 TR,2SC1740SR
87-026-463-080 TR,2SA933SRS
89-318-154-080 TR,2SC1815Y
89-112-965-080 TR,2SA1296GR
87-026-291-080 TR,DTC124XS
87-026-464-080 TR,DTC114TS
87-A30-476-010 TR,KTA1046Y
87-026-462-080 TR,2SC1740SRS
89-109-332-380 TR,2SA933RS
87-A30-515-080 TR,2SA1979O/Y
89-320-011-080 TR,2SC2001K<EZ,K>
87-A30-288-040 C-TR,DTC114YKA
87-A30-287-040 C-TR,DTC114TKA
87-A30-455-040 C-TR,DTA144EKA
87-026-239-080 C-TR,DTC114TK
87-026-237-080 C-TR,DTC124XK
87-A30-283-040 C-TR,DTA114YKA<EZ,K>
89-111-624-080 C-TR,2SA1162Y
89-503-025-010 C-FET,2SK302GR<EZ,K>
DIODE
87-A40-650-080 ZENER,MTZJ6.8A<EZ,K>
87-A40-509-080 ZENER,MTZJ6.8C<U>
87-070-345-080 DIODE,IN4148
87-A40-648-080 ZENER,MTZJ8.2A
87-A40-234-080 ZENER,MTZJ5.6A
87-017-978-080 DIODE,1N4003
87-017-932-080 ZENER,MTZJ6.2B
87-020-465-080 DIODE,1SS133
87-A40-465-010 DIODE,FR202
87-017-090-080 ZENER,HZS5B3
MAIN C.B
C211 87-A11-603-080 C-CAP,S 0.15-16 K B
C212 87-A11-603-080 C-CAP,S 0.15-16 K B
C215 87-016-460-080 C-CAP,S 0.22-16 B
C216 87-016-460-080 C-CAP,S 0.22-16 B
C231 87-010-213-080 C-CAP,S 0.015-50 B
C232 87-010-213-080 C-CAP,S 0.015-50 B
C233 87-A10-201-080 C-CAP,S0.33-16 KB
C234 87-A10-201-080 C-CAP,S0.33-16 KB
C235 87-016-669-080 C-CAP,S 0.1-25 K B
C236 87-016-669-080 C-CAP,S 0.1-25 K B
C237 87-010-371-080 CAP, ELECT 470-6.3V
C239 87-010-197-080 CAP, CHIP 0.01 DM<U>
C239 87-010-805-080 C-CAP,S 1-16 Z F<EZ,K>
C240 87-010-197-080 CAP, CHIP 0.01 DM<U>
C240 87-010-805-080 C-CAP,S 1-16 Z F<EZ,K>
C247 87-010-401-080 CAP, ELECT 1-50V
C248 87-010-401-080 CAP, ELECT 1-50V
C310 87-010-248-080 CAP, ELECT 220-10V
C316 87-010-263-080 CAP, ELECT 100-10V
C317 87-010-197-080 CAP,CHIP 0.01 DM
C801 87-010-248-080 CAP, ELECT 220-10V
REF. NO. DESCRIPTION PART NO. KANRI
C805 87-012-365-080 C-CAP,S 0.027-25VBK
C806 87-012-365-080 C-CAP,S 0.027-25VBK
C807 87-010-406-080 CAP, ELECT 22-50V
C808 87-010-405-080 CAP, ELECT 22-50V
C809 87-010-401-080 CAP, ELECT 1-50V
C810 87-010-401-080 CAP, ELECT 1-50V
C811 87-010-178-080 CHIP CAP 1000P
C812 87-010-178-080 CHIP CAP 1000P
C816 87-010-180-080 C-CER 1500P
C817 87-010-180-080 C-CER 1500P
C821 87-010-401-080 CAP, ELECT 1-50V
C822 87-010-401-080 CAP, ELECT 1-50V
C823 87-010-178-080 CHIP CAP 1000P
C824 87-010-178-080 CHIP CAP 1000P
C829 87-010-178-080 CHIP CAP 1000P
C830 87-010-178-080 CHIP CAP 1000P
C834 87-010-248-080 CAP, ELECT 220-10V
C843 87-A11-132-080 CAP, TC U 0.01-50 KB
C844 87-018-124-080 CAP, CER 270P-50V
C845 87-010-178-080 CHIP CAP 1000P
C846 87-010-263-080 CAP, ELECT 100-10V
C851 87-010-186-080 CAP,CHIP 4700P
C852 87-018-131-080 CAP, TC U 1000P
C853 87-A11-132-080 CAP,TC U 0.01-50 K B
CN201 87-099-018-010 CONN,16P
CN801 87-A60-110-010 CONN,4P V S2M-4W
CNA302 8B-CDA-629-010 CONN ASSY,6P MA-TU
CNA801 8B-CDA-630-010 CONN ASSY,4P RPH
L108 87-003-097-080 COIL,1.0UH K LAL02
L801 87-007-342-010 COIL,OSC 85K BIAS
SW801 8Z-CD9-609-010 SW,SL 1-6-2 PS62D01
CD C.B
C30 87-010-260-080 CAP, ELECT 47-25V
C251 87-010-405-080 CAP, ELECT 10-50V
C263 87-010-178-080 CHIP CAP 1000P
C264 87-010-178-080 CHIP CAP 1000P
C265 87-010-263-080 CAP, ELECT 100-10V
C266 87-010-263-080 CAP, ELECT 100-10V
C267 87-010-385-080 CAP, ELECT 220-25V
C268 87-010-385-080 CAP, ELECT 220-25V
C271 87-010-221-080 CAP, ELECT 470-10V
C272 87-010-221-080 CAP, ELECT 470-10V
C278 87-010-385-080 CAP, ELECT 220-25V
C279 87-010-235-080 CAP, ELECT 470-16V
C301 87-016-495-000 CAP,E 3300-25 M SMG
C306 87-010-404-080 CAP, ELECT 4.7-50V
C307 87-010-401-080 CAP, ELECT 1-50V
C308 87-010-221-080 CAP, ELECT 470-10V
C311 87-010-265-080 CAP, ELECT 33-16V
C312 87-010-385-080 CAP, ELECT 220-25V
C321 87-010-197-080 CAP, CHIP 0.01 DM
C322 87-010-263-080 CAP, ELECT 100-10V
C324 87-010-260-080 CAP, ELECT 47-25V
C325 87-010-405-080 CAP, ELECT 10-50V
C401 87-010-403-080 CAP, ELECT 3.3-50V
C402 87-010-197-080 CAP, CHIP 0.01 DM
C403 87-010-263-080 CAP, ELECT 100-10V
C404 87-010-248-080 CAP, ELECT 220-10V
C405 87-010-197-080 CAP, CHIP 0.01 DM
C406 87-010-374-080 CAP, ELECT 47-10V
C407 87-010-178-080 CHIP CAP 1000P
C408 87-010-198-080 CAP, CHIP 0.022
C409 87-010-248-080 CAP, ELECT 220-10V
C410 87-010-263-080 CAP, ELECT 100-10V
C411 87-A11-177-080 C-CAP,S 0.15-16 K B
C412 87-010-401-080 CAP, ELECT 1-50V
C413 87-016-369-080 C-CAP,S 0.033-25 B K
KANRI
NO.
– 4 –
REF. NO. DESCRIPTION PART NO.
NO.
C414 87-010-405-080 CAP, ELECT 10-50V
C416 87-010-545-080 CAP, ELECT 0.22-50V
C417 87-012-157-080 C-CAP,S 330P-50 CH
C418 87-010-213-080 C-CAP,S 0.015-50 B
C419 87-A11-608-080 C-CAP,S 0.33-25 K B
C420 87-016-369-080 C-CAP,S 0.033-25 B K
C421 87-A11-177-080 C-CAP,S 0.15-16 K B
C422 87-010-184-080 CHIP CAPACITOR 3300P(K)
C423 87-010-992-080 C-CAP,S 0.047-25 B
C424 87-A11-606-080 C-CAP,S 0.22-25 K B
C425 87-018-129-080 CAP,TC U 680P-50 K B
C426 87-A11-608-080 C-CAP,S 0.33-25 K B
C428 87-010-197-080 CAP, CHIP 0.01 DM
C429 87-010-186-080 CAP,CHIP 4700P
C430 87-012-156-080 C-CAP,S 220P-50 CH
C431 87-010-545-080 CAP, ELECT 0.22-50V
C432 87-010-374-080 CAP, ELECT 47-10V
C433 87-010-401-080 CAP, ELECT 1-50V
C434 87-010-184-080 CHIP CAPACITOR 3300P(K)
C435 87-010-197-080 CAP, CHIP 0.01 DM
C436 87-010-374-080 CAP, ELECT 47-10V
C437 87-010-404-080 CAP, ELECT 4.7-50V
C438 87-016-669-080 C-CAP,S 0.1-25 K B
C439 87-010-178-080 CHIP CAP 1000P
C440 87-018-139-080 CAP,TC U 1P-50 CH
C441 87-010-197-080 CAP, CHIP 0.01 DM
C442 87-018-109-080 CAP, TC U 22P-50 SL
C445 87-012-368-080 C-CAP,S 0.1-50 F
C446 87-012-368-080 C-CAP,S 0.1-50 F
C447 87-012-368-080 C-CAP,S 0.1-50 F
C448 87-010-315-080 C-CAP,S 27P-50 CH
C451 87-012-156-080 C-CAP,S 220P-50 CH
C455 87-010-247-080 CAP, ELECT 100-50V
C457 87-010-312-080 C-CAP,S 15P-50 CH
C458 87-010-312-080 C-CAP,S 15P-50 CH
C459 87-010-263-080 CAP, ELECT 100-10V
C460 87-015-819-080 CAPACITOR,0.01
C461 87-010-197-080 CAP, CHIP 0.01 DM
C462 87-010-248-080 CAP, ELECT 220-10V
C463 87-A11-132-080 CAP, TC U 0.01-50 KB
C465 87-010-404-080 CAP, ELECT 4.7-50V
C466 87-012-368-080 C-CAP,S 0.1-50 F
C467 87-010-263-080 CAP, ELECT 100-10V
C469 87-012-154-080 C-CAP,S 150P-50 CH
C470 87-018-131-080 CAP,TC U 1000P-50 KB UP050<EZ,K>
C471 87-018-209-080 CAP, TC U 0.1-50 ZF
C472 87-015-785-080 CHIP CAPACITOR, 0.1FZ-25Z
C473 87-015-785-080 CHIP CAPACITOR, 0.1FZ-25Z
C474 87-015-785-080 CHIP CAPACITOR, 0.1FZ-25Z
C475 87-A11-132-080 CAP, TC U 0.01-50 K B
C476 87-010-236-080 CAP,E 1000-10 SME
C477 87-010-197-080 CAP, CHIP 0.01 DM
C478 87-010-263-080 CAP, ELECT 100-10V
C479 87-010-197-080 CAP, CHIP 0.01 DM
C480 87-010-221-080 CAP, ELECT 470-10V
C481 87-010-405-080 CAP, ELECT 10-50V
C482 87-010-405-080 CAP, ELECT 10-50V
C489 87-012-368-080 C-CAP,S 0.1-50 F
C490 87-012-368-080 C-CAP,S 0.1-50 F
C491 87-A11-132-080 CAP, TC U 0.01-50KB
C492 87-010-221-080 CAP, ELECT 470-10V
C493 87-010-180-080 C-CER 1500P<U>
C501 87-012-368-080 C-CAP,S 0.1-50 F
C502 87-010-322-080 C-CAP,S 100P-50 CH
C503 87-018-119-080 CAP,TC U 100P-50 KB
C504 87-010-322-080 C-CAP,S 100P-50 CH
C505 87-010-322-080 C-CAP,S 100P-50 CH
C506 87-010-322-080 C-CAP,S 100P-50 CH
C510 87-016-669-080 C-CAP,S 0.1-25 K B
C831 87-010-198-080 CAP, CHIP 0.022
REF. NO. DESCRIPTION PART NO. KANRI
CN202 8A-CH4-687-010 CONN,4P V 2.5
CN205 87-A60-109-010 CONN,2P V S2M-2W
CN301 8A-CH4-689-010 CONN,3P V 2.5
CN401 87-A60-424-010 CONN,16P V TOC-B
CN403 87-099-201-010 CONN,8P 6216 H
CN802 8A-CH4-687-010 CONN,4P V 2.5
CNA202 8B-CDA-633-010 CONN ASSY,4P SP
CNA205 8B-CDA-626-010 CONN ASSY,2P DOOR
CNA402 8B-CDA-625-010 CONN ASSY,6P CD-ME
CNA802 8B-CDA-631-010 CONN ASSY,4P TA-ME
FFC401 8B-CDA-621-010 FF-CABLE,16P CD-RF
FFC403 8B-CDA-622-010 FF-CABLE,8P CD-FR
J201 87-A60-420-010 JACK,3.5 ST (MSC)
JW429 87-003-283-080 COIL,18UH J LAL02<EZ,K>
JW442 87-003-098-080 COIL,2.2UH K LAL02<EZ,K>
L401 87-003-102-080 COIL, 10UH
L402 87-003-098-080 COIL,2.2UH K LAL02<EZ,K>
L404 87-003-152-080 COIL, 100UH
R840 87-029-124-010 RES,FUSE 2.2-1/4
SFR430 87-024-437-080 SFR,100K RH063MC
X401 8Z-CD5-633-010 VIB, CER16.93MHZ FCR16.93M2
FRONT C.B
C601 87-010-196-080 C-CAP,S 0.1-25 Z F C2012
C602 87-010-555-040 CAP,E 100-10 M 5L SRE
C603 87-A10-189-040 CAP,E 220-10 M 5L
C604 87-010-196-080 C-CAP,S 0.1-25 Z F C2012
C605 87-018-150-080 CAP,TC U 18P-50 J CH UP050
C606 87-018-111-080 CAP,TC U 27P-50 J SL UP050
C607 87-018-116-080 CAP,TC U 56P-50 J SL UP050
C608 87-018-114-080 CAP,TC U 39P-50 J SL UP050
C609 87-018-149-080 CAP,TC U 15P-50 J CH UP050
C610 87-015-785-080 C-CAP,0.1-25 Z F C3216
C611 87-010-197-010 CAP,CHIP 0.01 DM
C612 87-018-131-080 CAP,TC U 1000P-50 K B UP050
C613 87-A10-826-080 C-CAP,S 1-10 K B
C614 87-010-494-040 CAP,E 1-50 M 5L SRE
C615 87-010-493-040 CAP,E 0.47-50 M 5L SRE
C616 87-010-196-080 C-CAP,S 0.1-25 Z F C2012
C617 87-010-495-040 CAP E 2.2-50 M 5L SRE
C618 87-010-197-010 CAP, S 0.01-25<U>
C619 87-010-197-010 CAP, S 0.01-25
C625 87-010-197-010 CAP,CHIP 0.01 DM
C626 87-010-197-010 CAP,CHIP 0.01 DM
C627 87-010-197-010 CAP,CHIP 0.01 DM
CN601 87-099-757-010 CONN,16P H 9604
CN602 87-A60-079-010 CONN,08P H 9604S-08F
CNA603 8B-CHA-610-010 CONN ASSY,4P TU-FR
FFC601 8B-CDA-620-010 FF-CABLE,16P FR-MAIN
L601 87-003-102-080 COIL,10UH J LAL02
L602 87-003-102-080 COIL,10UH J LAL02
LCD601 8B-CHA-620-010 LCD,AIW4239-32PIN
LED601 8A-CDA-646-010 LED,6224-10GD GRN<U>
LED602 8A-CDA-645-010 LED,6224-10ID RED
LED603 8A-CDA-645-010 LED,6224-10ID RED
S601 87-A92-170-080 SW,TACT EVQPAD05R
S602 87-A92-170-080 SW,TACT EVQPAD05R
S603 87-A92-170-080 SW,TACT EVQPAD05R
S604 87-A92-170-080 SW,TACT EVQPAD05R
S605 87-A92-170-080 SW,TACT EVQPAD05R
S606 87-A92-170-080 SW,TACT EVQPAD05R
S607 87-A92-170-080 SW,TACT EVQPAD05R<U>
S608 87-A92-170-080 SW,TACT EVQPAD05R<U>
S609 87-A91-704-080 SW,TACT EVQ 214 05R<EZ,K>
S611 87-A92-170-080 SW,TACT EVQPAD05R
S612 87-A92-170-080 SW,TACT EVQPAD05R
S613 87-A92-170-080 SW,TACT EVQPAD05R
S614 87-A92-170-080 SW,TACT EVQPAD05R
KANRI
NO.
– 5 –
REF. NO. DESCRIPTION PART NO.
NO.
S615 87-A92-170-080 SW,TACT EVQPAD05R
X601 87-030-273-010 VIB,XTAL 32.768KHZ DT-38 5P
X602 87-030-376-080 VIB,CER 5.760MHZ CSA MG200
TUNER C.B
C1 87-010-312-080 C-CAP,S 15P-50 J CH GRM
C2 87-010-316-080 C-CAP,S 33P-50 CH
C3 87-010-312-080 C-CAP,S 15P-50 J CH GRM
C5 87-012-360-080 C-CAP,S 1-10 Z F CM/CB<EZ,K>
C6 87-010-313-080 C-CAP,S 18P-50 J CH GRM<U>
C7 87-012-140-080 C-CAP,S 470P-50 J CH<U>
C7 87-014-049-080 CAP,PP 470P-100 J PL<EZ,K>
C8 87-012-349-080 C-CAP,S 1000P-50 J CH GRM
C10 87-010-197-080 CAP, CHIP 0.01 DM
C11 87-010-197-080 CAP, CHIP 0.01 DM
C12 87-010-197-080 CAP, CHIP 0.01 DM
C13 87-010-150-080 C-CAP,S 6P-50 D CH
C14 87-010-303-080 C-CAP,330P-50 J CH
C15 87-010-178-080 C-CAP,S 1000P-50 K B C2012
C16 87-010-374-080 CAP,E 47-10 M 11L SME
C17 87-010-198-080 C-CAP,S 0.022-25 K B C2012
C18 87-015-835-080 C-CAP,0.047-50 K B
C19 87-010-263-080 CAP,E 100-10 M 11L SME
C20 87-010-404-080 CAP,E 4.7-50V
C23 87-010-197-080 CAP, CHIP 0.01 DM
C24 87-010-303-080 C-CAP,330P-50 J CH
C25 87-016-460-080 C-CAP,S 0.22-16 K B
C27 87-A11-067-080 C-CAP,S 1-10 K B
C28 87-016-669-080 C-CAP,S 0.1-25 K B
C29 87-016-669-080 C-CAP,S 0.1-25 K B
C30 87-012-365-080 C-CAP,S 0.027-25 K B<U>
C30 87-010-220-080 C-CAP,S 0.018-25 K B<EZ,K>
C31 87-012-365-080 C-CAP,S 0.027-25 K B<U>
C31 87-010-220-080 C-CAP,S 0.018-25 K B<EZ,K>
C33 87-012-358-080 C-CAP,S 0.47-10 Z F CM/CB
C34 87-012-358-080 C-CAP,S 0.47-10 Z F CM/CB
C35 87-010-197-080 CAP, CHIP 0.01 DM
C36 87-010-263-080 CAP, ELECT 100-10V
C37 87-010-197-080 CAP, CHIP 0.01 DM
C38 87-010-263-080 CAP,E 100-10 M 11L SME
C39 87-010-404-080 CAP,E 4.7-50 M 11L SME
C40 87-010-197-080 CAP, CHIP 0.01 DM
C41 87-010-178-080 C-CAP,S 1000P-50 K B C2012
C42 87-010-178-080 C-CAP,S 1000P-50 K B C2012
C43 87-010-178-080 C-CAP,S 1000P-50 K B C2012
C44 87-010-311-080 C-CAP,S 12P-50 J CH GRM
C45 87-010-312-080 C-CAP,S 15P-50 J CH GRM
C46 87-010-197-080 CAP, CHIP 0.01 DM
C47 87-010-197-080 CAP, CHIP 0.01 DM
C48 87-010-197-080 CAP, CHIP 0.01 DM
C49 87-012-140-080 C-CAP,S 470P-50 J CH
C50 87-010-197-080 CAP, CHIP 0.01 DM
C51 87-010-316-080 C-CAP,S 33P-50 J CH GRM<EZ,K>
C52 87-010-197-080 CAP, CHIP 0.01 DM<EZ,K>
C53 87-010-197-080 CAP, CHIP 0.01 DM<EZ,K>
C54 87-010-177-080 C-CAP,S 820P-50 J SL<EZ,K>
C55 87-010-197-080 CAP, CHIP 0.01 DM<EXCEPT U>
C56 87-010-312-080 C-CAP,S 15P-50 J CH GRM<EZ,K>
C71 87-010-197-080 CAP, CHIP 0.01 DM
C72 87-010-263-080 CAP, ELECT 100-10V
C73 87-010-197-080 CAP, CHIP 0.01 DM
C75 87-010-197-080 CAP, CHIP 0.01 DM
C80 87-010-197-080 CAP, CHIP 0.01 DM
C92 87-010-197-080 CAP, CHIP 0.01 DM
C93 87-010-197-080 CAP, CHIP 0.01 DM
CF1 87-A91-094-010 FLTR,CDA10.7 MG80A
CF2 87-008-261-010 FILTER, SFE10.7MA5-A
CN2 87-099-854-010 CONN,6P V S2M-6W
CN3 87-A60-110-010 CONN,4P V S2M-4W
REF. NO. DESCRIPTION PART NO. KANRI
KANRI
NO.
D3 87-A40-616-070 VARI-CAP,SVC384(S/T)
D4 87-A40-916-040 C-VARI-CAP,HVC202A
D5 87-A40-916-040 C-VARI-CAP,HVC202A
L2 87-A50-560-010 COIL,FM BPF(ACD)
L3 8A-CH4-670-010 BAR-ANT,MW 2B-ACH(COI)<U>
L3 8A-CH4-671-010 BAR-ANT,MW/LW 3B-ACH(COI)<EZ,K>
L4 87-A50-420-010 COIL,MW OSC(SYN)
L5 87-A50-566-010 COIL,FM RF EX(ACH)
L6 87-A50-567-010 COIL,FM OSC(ACH)
L7 87-A91-308-010 FLTR,PCFAZH- 450T (TOK)
L8 87-005-849-080 COIL,10UH K CECS
L51 87-A50-421-010 COIL,LW OSC(SYN)<EZ,K>
TC1 87-011-254-080 TRIMMER,CER 20P 4.0X4.5 ECR
TC51 87-A91-659-010 TRIMMER,50P 4.0X4.5 ECRL<EZ,K>
X1 87-A70-061-010 VIB,XTAL 4.500MHZ CSA-309
BATT C.B
C901 87-010-192-080 C-CAP,S 0.022-50 F
C902 87-010-192-080 C-CAP,S 0.022-50 F
C903 87-010-192-080 C-CAP,S 0.022-50 F
C904 87-010-192-080 C-CAP,S 0.022-50 F
CNA901 8B-CDA-627-010 CONN ASSY,3P PWR
J901 87-A60-178-010 JACK,AC E W/SW<EZ,K>
!
J901 87-A60-177-010 JACK,AC U W/SW<U>
!
PR901 87-A91-940-080 PROTECTOR,2.5A 20P 60V
!
!
PT901 8A-CDA-612-010 PT,E 2.5W<EZ,K>
!
PT901 8A-CDA-611-010 PT,U 2.5W<U>
SP901 8A-CDA-214-010 SPR-C,BATT
SP902 8A-CDA-214-010 SPR-C,BATT
BATT INF C.B
SP903 8A-CDA-214-010 SPR-C,BATT
SP904 8A-CDA-214-010 SPR-C,BATT
CD MOTOR C.B
M2 S0-M10-A09-700 MOTOR SLED ASSY
PIN3 S2-369-750-000 PLUG,6P
SW1 S4-S13-A01-600 SW,LEAF
– 6 –
CHIP RESISTOR PART CODE
Chip Resistor Part Coding
88
A
Resistor Code
Chip resistor
Wattage Type Tolerance
1/16W 1005 5% CJ
1/16W
1/10W
1/8W
1608
2125
3216
5%
5%
5%
TRANSISTOR ILLUSTRATION
Symbol
CJ
CJ
CJ
Figure
Value of resistor
Form
L
Dimensions (mm)
t
W
0.55
Resistor Code
108
118
128
LW t
1.0 0.5 0.35 104
1.6 0.8 0.45
2 1.25 0.45
3.2
1.6
: A
: A
C
E C B
2SA1979O/Y
2SC2001K
S
D
G
2SK302GR
E C B
2SA1296GR
2SC1815Y
B C E
KTA1046Y
E C B
2SA933RS
2SA933SRS
2SC1740SR
2SC1740SRS
DTC114TS
DTC124XS
B
E
2SA1162Y
DTA114EKA
DTA114YKA
DTC114TK
DTC114TKA
DTC114YKA
DTC124XK
– 7 –
LCD DISPLAY (AIW4239-32PIN)
8
WIRING 1 (MAIN / CD)
32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
9
R
S
T
U
SCHEMATIC DIAGRAM – 1 (MAIN / CD : 1 / 2)
– 10 –
SCHEMATIC DIAGRAM – 2 (CD : 2 / 2 / CD MOTOR)
– 11 –
WIRING 2 (FRONT / BATT / BATT INF)
32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
12
R
S
T
U
SCHEMATIC DIAGRAM 3 (FRONT)
13
SCHEMATIC DIAGRAM – 4 (BATT / BATT INF)
– 14 –
WIRING 3 (TUNER)
32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
A
B
C
D
,
E
F
TP
(VT)
,
G
H
I
J
K
L
M
N
O
15
P
Q
R
S
T
U
SCHEMATIC DIAGRAM – 5 (TUNER) <U>
– 16 –
SCHEMATIC DIAGRAM 6 (TUNER) <EZ, K>
17
WIRING 4 (CD MOTOR)
1 51 41 31 21 11 0987654321
G CD MOTOR C.B
M2
_
(SLED MOTOR)
M2
A
B
C
D
+
6
5
3
1
TO MAIN C.B CNA402
PICK UP ASSY
SF-P101NR
PIN3
SW1
(INSIDE LIMIT SW)
SW1
_
(SPINDLE MOTOR)
M1
M1
E
F
G
H
+
I
J
K
L
M
16
18
CN1
1
FFC401
TO MAIN C.B CN401
N
O
P
Q
R
S
T
U
IC BLOCK DIAGRAM
19
20
IC DESCRIPTION
IC, LC78622NE
Description Pin No. Pin Name I/O
1 DEFI I Defect detection signal (DEF) input.
2 TAI I Test input. A pull-down resistor is incorporated. (For PLL) (Connected to 0V)
3 PDO O Phase comparison output to control the external VCO. (For PLL)
4 VVSS – Ground of the built-in VCO. Normally, 0V. (For PLL)
5 ISET I For the connection of a resistor which adjusts the PDO output current. (For PLL)
6 VVDD – Power supply of the built-in VCO. (For PLL)
7 FR I Adjusts the VCO frequency range. (For PLL)
8 VSS – Ground of digital circuits. Normally, 0V.
9 EFMO O Slice level control EFM signal output.
10 EFMIN I Slice level control EFM signal input.
11 T2 I Test input. A pull-down resistor is incorporated. (Connected to 0V)
12 CLV+
13 CLV-
O Disc motor control tri-state output.
14 V/P O
15 HFL I Track detection signal input. Schmitt trigger input.
16 TES I Track error signal input. Schmitt trigger input.
17 TOFF O Tracking OFF output.
18 TGL O Tracking gain switching output. "L" raises the gain.
19 JP+
O Track jump control tri-state output.
20 JP-
21 PCK O Monitors clock signal for EFM data playback. 4.3218MHz when the phase is locked. (Not used)
22 FSEQ O
23 VDD – Power supply of digital circuits.
24 SL+
O Serial data command sled signal output terminal from microprocessor.
25 SL–
26 NC – Not connected.
27 PU IN I CD pickup inside limit switch.
28 RW O Read / Write signal.
29 EMPH O De-emphasis monitor. "H": when playing a de-emphasis disc. (Not used)
Output to monitor the automatic switching between the rough servo control and phase servo
control. "H": Rough servo, "L": Phase servo.
Sync signal detection output. Goes "H" when the sync signal detected from the EFM
signal matches the sync signal generated internally. (Not used)
30 C2F O C2 flag output. (Not used)
31 DOUT O Output a digital OUT signal. (EIAJ format) (Not used)
32 T3
33 T4
34 NC – Not connected.
35 MUTEL O Left channel 1-bit D/A converter muting output. (Not used)
I Test input. (Connected to 0V).
– 21 –
I/O Description Pin No. Pin Name
36 LVDD – Left channel 1-bit D/A converter power supply.
37 LCHO O Left channel 1-bit D/A converter output.
38 LVSS – Left channel 1-bit D/A converter ground. Normally, 0V.
39 RVSS – Right channel 1-bit D/A converter ground. Normally, 0V.
40 RCHO O Right channel 1-bit D/A converter output.
41 RVDD – Right channel 1-bit D/A converter power supply.
42 MUTER O Right channel 1-bit D/A converter muting output. (Not used)
43 XVDD – Power supply of crystal oscillator.
44 XOUT O
45 XIN I
46 XVSS – Ground of crystal oscillator. Normally, 0V.
47 SBSY O Subcode block sync signal output. (Not used)
48 EFLG O C1, C2, single, duplex correction monitor. (Not used)
49 PW O Output of subcodes P, Q, R, S, T, U and W. (Not used)
50 SFSY O Subcode frame sync signal output. Falls when the subcode is set to the standby state. (Not used)
For the connection of a 16.93MHz crystal oscillator.
51 SBCK I
52 FSX O 7.35kHz sync signal output obtained by dividing the oscillator frequency. (Not used)
53 WRQ O Subcode Q standby output.
54 RWC I Read/write control input. Schmitt trigger input.
55 SQOUT O Subcode Q output.
56 COIN I Command input from the microprocessor.
57 CQCK I
58 RES I LC78622NE reset input.
59 T11 O Test output. Set to open (normally, "L" output.) (Not used)
60 16M O 16.9344MHz output. (Not used)
61 4.2M O 4.2336MHz output.
62 T5 I Test input. A pull-down resistor is incorporated. (Connected to 0V)
63 CS I Chip select input. (Connected to 0V)
64 T1 I Test input with no pull-down resistor. (Connected to 0V)
Subcode read-out clock input. Schmitt trigger input. ("L" is applied when not used.) (Connected to 0V)
Command input retrieval clock or subcode retrieval clock input from SQOUT. Schmitt trigger
input.
– 22 –
IC, LA9241ML
Description Pin No. Pin Name I/O
1 FIN2 O
2 FIN1 O For the connection of the pickup photodiode.
3E O
4 F O For the connection of the pickup photodiode.
5 TB I Inputs the DC components in the TE signal.
6 TE- O
7 TE O TE signal output.
8 TESI I TES (track error sense) comparator input. The TE signal is passed through a BPF.
9 SCI I Shock detection input.
10 TH I Sets the time constant for the tracking gain.
11 TA O TA amp output.
12 TD- I Composes the tracking phase compensation constant between the TD and VR pins.
13 TD O Sets the tracking phase compensation.
14 JP I Sets the amplitude of the tracking jump signal (kick pulses).
15 TO O Tracking control signal output.
16 FD O Focusing control signal output.
For the connection of the pickup photodiode. Addition to the FIN1 pin creates an RF
signal and subtraction from it create an EF signal.
For the connection of the pickup photodiode. Subtraction from the F pin creates a TE
signal.
For the connection of a resistor which sets the gain of the TE signal between this pin
and the TE pin.
17 FD- I Composes the focusing phase compensation constant between the FD and FA pins.
18 FA O Composes the focusing phase compensation constant between the FD- and FA- pins.
19 FA- I Composes the focusing phase compensation constant between the FA and FE pins.
20 FE O FE signal output.
21 FE- I
22 A-GND O Ground of analog signals.
23 SP O Single-ended output of the signals input to the CV+ and CV- pins.
24 SPI I Spindle amp input.
25 SPG I For the connection of a resistor which sets the gain in the spindle 12cm mode. (Not used)
26 SP- I For the connection of the spindle phase compensation constant with the SPD pin.
27 SPD O Spindle control signal output.
28 SLEQ I For the connection of sled phase compensation constant.
29 SLD O Sled control signal output.
30 SL-
31 SL+
32 JP-
33 JP+
For the connection of a resistor whichs sets the gain of the FE signal between this pin
and the TE pin.
I Sled feed signal input from the microprocessor.
I Tracking signal input from the DSP.
34 TGL I Tracking gain control signal input from the DSP. Low gain when TGL is "H".
35 TOFF I Tracking off control signal input from the DSP. Off when TOFF is "H".
36 TES O Outputs the TES signal to the DSP.
– 23 –
Pin No.
I/O Description Pin Name
37 HFL O
38 SLOF I Sled servo off control input.
39 CV-
40 CV+
41 RFSM O RF output.
42 RFS- O Sets the RF gain and the EFM signal's 3T compensation constant together with the RFSM pin.
43 SLC O
44 SLI I Input to control the DSP's data slice level.
45 DGND – Ground of digital signals.
46 FSC O Output for the focus search smoothing capacitor.
47 TBC I The TBC (tracking balance control) signal sets the EF balance variation range.
48 NC – Not connected.
49 DEF O Disc defect detection output.
50 CLK I Reference clock input. 4.23MHz is input from the DSP.
51 CL I Microprocessor command clock input.
52 DAT I Microprocessor command data input.
The HFL (high frequency level) signal is used to judge whether the main beam is positioned on
the pit or on the mirror.
I CLV error signal input from the DSP.
The SLC (slice level control) signal is output to control the DSP's data slice level of the RF
waveform.
53 CE I Microprocessor chip enable input.
54 DRF O DRF (detect RF) is an output to detect the RF level.
55 FSS I
56 VCC2 – VCC of servo and digital circuits.
57 REFI – For the connection of bypass capacitor for the reference voltage.
58 VR O Reference voltage output.
59 LF2 I Sets the time constant for disc defect detection.
60 PHI I For the connection of a capacitor to hold the RF signal peak.
61 BHI I For the connection of a capacitor to hold the RF signal bottom.
62 LDD O APC circuit output.
63 LDS I APC circuit input.
64 VCC1 – VCC of RF signal circuits.
The FSS (focus search select) signal switches the focus search modes (+/-search / +search with
respect to the reference voltage). (Not used)
– 24 –
IC, LC867132V-5T67
Pin No. Pin Name I/O Description
1
O-RWC/CE
O
CD read/write control output and TU CE.
10
11
12
13
14
15
16
17
18
2
3
4
5
6
7
8
9
O-DATA
O-CLK
O-DI
O-CLK.SFT
I-HOLD
I-RST
XT1 (IN)
XT2 (OUT)
VSS1
CF1 (IN)
CF2 (OUT)
VDD1
I-FM.ST
I-KEY0
I-CD SW
I-KEY1
I-MOTOR
O
Data output to sound processor IC M62495AFP<EZ,K>, IC M61509FP<U>.
O
Clock output to sound processor IC M62495AFP<EZ,K>, IC M61509FP<U>.
O
Data input to tuner PLL.
O
Clock shift output for microprocessor.
I
Hold status detection.
I
Microcomputer reset.
I
Connected to an external 32.768kHz crystal oscillator.
O
Connected to an external 32.768kHz crystal oscillator.
–
GND.
I
Connected to an external 5.76MHz ceramic filter.
O
Connected to an external 5.76MHz ceramic filter.
–
Microprocessor power supply (+5V).
I
FM STEREO status input.
I
KEY AD input.
I
CD door switch status detection input.
I
KEY AD input.
I
DECK MECHA MOTOR status input.
19
20
21
22
23
24
25
26
27
28
29
30
31
32 ~ 40
41
42
43 ~ 51
I-REC
NC
I-DO
O-BASS.LED
O-QS.LED
NC
O-INT
I-DRF
I-WRSQ
I-RMC
SEG1
SEG2/LW
SEG3/AM 10K
SEG4 ~ SEG12
VDD3
VSS3
SEG13 ~ SEG21
I
REC status input. (Connected to GND through a resistor).
–
Not connected.
I
Data input from tuner PLL.
O
BASS LED ON/OFF control output. (Not used)
O
Q-Sound LED ON/OFF control output.
–
Not connected.
O
INT DIODE MATRIX detection output.
I
CD RF level detection input.
I
CD sub-code Q standby input.
I
Remote control input.
O
LCD segment output.
O
LCD segment output / Intial settings output (LW) <EZ,K only>.
O
LCD segment output / Intial settings output (AM 10K) <U only>.
O
LCD segment output.
–
Power supply for microcomputer (+5V).
–
GND.
O
LCD segment output.
52 ~ 63
64 ~ 66
67
68
69
70
NC
COM1 ~ COM3
NC
VSS2
VDD2
O-CD
–
Not connected.
O
LCD common output.
–
Not connected.
–
GND.
–
Power supply for microcomputer (+5V).
O
CD power control output.
– 25 –
Pin No. Pin Name I/O Description
71
O-TU
O TUNER power control output.
72
73
74
75, 76
77
78
79
80
O-P.CONT
NC
O-MUTE
NC
O-BEAT CONT
O-COIN
I-SQOUT
O-SQCK
O Power supply control output.
– Not connected.
O Main mute output.
– Not connected.
O BEAT switch over output.
O CD command output.
I CD sub-code Q input.
O CLK for CD commands/sub-codes.
– 26 –
VOLTAGE CHART
IC001, TA2149N
IC203, M61509FP / M62495AFP
PIN NO. FM AM
100
2 0.79 0
3 0 1.01
4 4.65 4.79
5 4.84 4.83
6 4.3 4.16
7 4.84 4.83
800
9 0.21 0.18
10 4.06 4.34
11 1.19 1.19
12 1.21 1.22
13 3.93 0
14 4.16 0.02
15 0.7 0.7
16 0.94 1.09
17 0.9 1.3
18 4.79 4.74
19 3.1 3.22
20 4.84 4.83
21 4.64 4.76
22 4.84 4.83
23 4.64 4.76
PIN NO. FM AM
15 0 0
16 2.4 2.4
17 4.8 4.8
18 0.8 0.8
19 0.8 0.8
20 5 5
21 0 0
22 2.4 2.4
IC202, TA8227P
PIN NO. ACTIVE STATIC
1 12.31 11.5
2 6.57 6.1
3 12 1.5
400
5 0.56 0.56
6,7 0 0
8 0.56 0.56
9 6.65 6.41
10 12 1.42
11 6.46 6.2
12 13.1 12.5
PIN NO. CD TAPE TUNER
1 2.54 2.55 2.56
2,3 2.55 2.55 2.56
4 0.7 0.8 2.56
5 2.54 2.55 2.57
6 2.56 2.56 2.57
7 2.55 2.55 2.57
8 2.55 2.56 2.57
9 2.55 2.55 2.56
10 2.55 2.55 2.57
11 2.56 2.56 2.57
12 5.08 5.09 5.11
13 2.82 2.83 2.83
14 0 0 0
15,16 2.55 2.55 2.56
17 2.55 2.56 2.57
18 2.55 2.55 2.56
19 2.57 2.57 2.58
20 2.54 2.55 2.57
21 0.7 0.58 0.69
22 2.54 2.06 2.56
23 2.55 2.56 2.56
24 2.54 2.55 2.56
24 4.83 4.83
IC002, LC72131D-N
PIN NO. FM AM
1 2.4 2.4
200
300
400
500
6 4.8 4.8
700
8 1.3 1.3
9 4.7 0
10 4.0 0
11 4.8 0
12 0 0
13 0.9 0.9
14 0 0
– 27 –
IC401, LA9241ML
PIN NO. ACTIVE STATIC
1 2.67 2.53
2 2.65 2.53
3 2.67 2.53
4 2.67 2.56
5 2.67 2.53
6 2.66 2.55
7,8 2.67 2.55
9 2.65 2.54
10 2.66 2.52
11 2.67 2.55
12 2.7 2.54
13 2.67 2.55
14 2.7 2.54
15 2.72 2.54
16 2.69 2.54
17 2.67 2.55
18 2.69 2.55
19 2.73 2.54
PIN NO. ACTIVE STATIC
45 0 0
46 2.64 2.54
47 2.65 2.55
48,49 0 0
50 2.54 2.44
51 4.77 4.71
52 4.86 4.71
53 0 0.07
54 5.11 0.03
55 0.16 0.14
56 5.2 5.01
57 2.64 2.54
58 2.64 2.56
59 2.59 0.98
60 2.57 0.99
61 2.3 2.24
62 3.86 4.35
63 0.19 0
PIN NO. ACTIVE STATIC
21 2.7 2.48
22 5.6 0
23 5.6 5.02
24,25 0 0
26 0 5
27 5.6 5
28,29 0 0
30 0 4.95
31 2.8 2.48
32~34 0 0
35 0 5.02
36 5.3 4.77
37 2.15 1.94
38,39 0 0
40 2.15 1.95
41 5.3 4.77
42 0 5
43 5.5 5.02
20 2.69 2.54
21 0 2.54
22 2.67 0
23 2.67 2.53
24 2.65 2.54
25 2.69 2.56
26 2.75 2.56
27 2.75 2.5
28 2.68 2.55
29 2.75 2.55
30 2.45 2.33
31 2.45 2.34
32,33 0 0
34 5.22 5.01
35 0 5.01
36 1.4 0.04
37 0 0.01
38 0 5
39 0 0
40 0.25 0
41 2.45 1.61
42 2.54 2.45
43 2.54 2.41
44 2.63 2.53
64 5.18 5.02
IC402, LC78622NE
PIN NO. ACTIVE STATIC
100
200
3 1.8 0.01
400
5 2.1 1.85
6 5.6 4.98
7 0.4 0.07
800
9 2.8 2.52
10 2.7 2.41
11 0 0
12 0.3 0
13 0 0
14 0 5
15 0 0.01
16 1.5 0.04
17 0 5.01
18 5.6 5.01
19,20 0 0
44 2.3 2.08
45 2.3 2.06
46 2.3 0
47 0.1 0.08
48 0 2.27
49 0.1 0
50 2.77 2.5
51 0 0
52 2.77 2.5
53 0.9 0
54 0 0.07
55 0 0
56 5.16 4.71
57 5 4.71
58 5.5 5
59 0 0
60 2.25 2.02
61 2.66 2.41
62~64 0 0
– 28 –
IC404, MM1469XH
IC601, LC867132V-5T67
PIN NO. ACTIVE STATIC
1 4.2 3.61
2 4.2 3.62
3,4 2.95 2.54
5 8.2 7.24
6,7 5.8 5.02
800
9 2.95 2.55
10 3 2.55
11 4.27 3.61
12 4.01 3.63
13 0 0
14 8.4 7.39
15 1.45 0.78
16 1.45 0.8
17 4.1 3.63
18 4.1 3.62
19 2.9 2.54
20 2.9 2.55
21,22 8.9 7.96
23,24 2.9 2.55
25 2.9 2.54
26 4.5 3.61
27 3.71 3.62
28 0 0
PIN NO. TAPE TUNER CD
1 0.01 0.01 0.01
2 0.02 0.01 0.02
3,4 0.01 0.01 0.01
5 0.01 0.01 0.03
6 0.03 0.03 0.03
7 4.01 4.70 4.61
8 1.7 1.74 1.69
9 2.47 2.52 2.46
10 0.01 0.01 0.01
11 2.08 4.41 2.08
12 2.19 4.84 2.19
13 4.74 4.85 4.74
14 0 4.79 0.02
15 4.93 4.95 4.93
16 4.6 4.73 4.71
17 4.93 4.95 4.93
18 0.73 0.73 0.73
19,20 0.61 0.01 0.04
21 0 4.82 0.01
22~24 0.01 0.01 0.01
25 4.74 4.85 4.74
26,27 0.02 0.03 0.37
28 5.17 5.27 5.17
29 0 2.45 2.37
30 0.38 2.45 2.37
31 2.43 2.41 2.37
32 2.43 0.85 2.43
33 2.40 2047 2041
34 0.6 2.47 2.41
PIN NO. TAPE TUNER CD
48 2.43 2.45 2.43
49 2.43 2.42 2.43
50 2.43 2.47 2.43
51 2.41 2.47 2.42
52 2.43 2.47 2.43
53,54 0.01 0 0.01
55 0.01 0 4.68
56 0.01 0 0.01
57 4.75 4.78 0.01
58~60 0.01 0 0.01
61 0.05 0.15 0.42
62 0.04 0.1 0.45
63 0.03 0.61 0.34
64 2.41 2.47 2.41
65 2.42 2.44 2.41
66 2.41 2.48 2.41
67 0.01 1.25 0.04
68 0.01 0 0.01
69 4.74 4.84 4.74
70 0.01 0 4.74
71 0.01 4.85 0.01
72 4.73 4.83 4.74
73 4.75 0.15 4.74
74 0.01 0.01 4.67
75~77 0.01 0.01 0.01
78 0.01 0.01 4.74
79 1.15 0.01 0
80 0.01 0.45 4.74
35 2.40 2.46 2.41
36 2.43 2.48 2.41
37 0.6 2.48 2.43
38 2.43 2.48 2.43
39 2.43 2.48 2.39
40 2.43 2.41 2.38
41 4.75 4.85 4.75
42 0.01 0.01 0.01
43 2.43 2.46 2.43
44 2.43 2.48 2.43
45 2.43 2.47 2.41
46 2.43 2.45 2.43
47 2.43 2.42 2.44
– 29 –
IC801, NJM14558LD
PIN NO. TAPE REC
1 3.37 3.38
2 3.37 3.39
3 3.34 3.35
400
5 3.34 3.35
6 3.37 3.39
7 3.37 3.38
8 6.83 6.82
Q002
Q244
Q310
PIN FM AM
E 4.82 4.9
C88
B 5.52 5.58
Q003
PIN FM AM
E 5.53 5.59
C 5.52 5.59
B 4.85 4.9
Q004
PIN FM AM
E00
C 4.06 4.12
B 2.98 3.03
Q052 <EZ,K>
PIN ACTIVE STATIC
E00
C00
B 0.12 0.64
Q301
PIN ACTIVE STATIC
E 12.2 12.66
C 11.4 12
B 11.5 11.99
Q302
PIN ACTIVE STATIC
E 11.5 11.99
C 11.4 12
B 10.9 11.32
Q303
PIN ACTIVE STATIC
E 5.55 5.56
C 10.45 10.83
B 6.25 6.26
Q321
PIN ACTIVE STATIC
E00
C 0.01 0.02
B 0.6 0.7
Q401
PIN ACTIVE STATIC
E 4.46 4.99
C 2.11 1.56
B 3.76 4.35
Q402
PIN FM AM
E 0.01 0.01
C 0.61 0.62
B 4.82 0
Q054 <EZ,K>
PIN FM AM
E 4.82 4.81
C 0 4.75
B 4.79 0.03
Q071
PIN FM AM
E00
C 0.02 0.01
B 4.42 4.42
Q243
PIN ACTIVE STATIC
E00
C00
B 4.57 4.57
Q304
PIN ACTIVE STATIC
E 11.38 11.97
C 7.94 7.98
B 10.75 11.34
Q305
PIN ACTIVE STATIC
E 7.23 7.26
C 10.56 11.23
B 7.85 7.87
Q306
PIN ACTIVE STATIC
E 7.87 7.97
C 5.3 5.15
B 7.17 7.28
Q403
PIN ACTIVE STATIC
E 2.56 2.56
C 2.56 2.56
B00
Q406
PIN ACTIVE STATIC
E00
C 4.6 4.6
B00
Q407
PIN ACTIVE STATIC
E00
C00
B 0.12 0.64
PIN ACTIVE STATIC
E 5.08 5.09
C 7.94 7.98
B 10.75 5.81
– 30 –
PIN ACTIVE STATIC
E 4.6 4.58
C 2.57 2.55
B 2.56 2.55
Q408
Q492
Q810
PIN ACTIVE STATIC
E 4.6 4.58
C 2.57 0.55
B 2.56 2.55
Q491
PIN ACTIVE STATIC
E 7.91 7.98
C 7.88 7.97
B 7.15 7.23
PIN ACTIVE STATIC
E00
C 0.14 0.14
B 4.41 4.41
Q801
PIN TAPE REC
E 0 1.64
C 0 5.9
B 0 2.31
PIN TAPE REC
E 3.36 3.38
C 0.05 13.85
B 0.13 0.13
Q841
PIN TAPE REC
E00
C 0.72 0.01
B 0 5.73
– 31 –
ADJUSTMENT <TUNER / DECK / CD>
< TUNER SECTION >
1. AM IF Adjustment
L007 ................................................450kHz
2. AM(MW) VT Adjustment
Settings : • Test Point : C39 ) (VT)
• Adjustment location : L004
Method : Set to AM 1000kHz(U), MW 999kHz(EZ, K) and adjust
L004 so that the test point becomes 3.75V±0.1V(U),
3.8V± 0.1V(EZ, K).
3. AM(MW) Tracking Adjustment
L003 (1/2) ................................. 600kHz(U)
L003 (1/2) .......................... 603kHz(EZ, K)
TC001 ..................................... 1400kHz(U)
TC001 .............................. 1404kHz(EZ, K)
4. FM VT Adjustment
Settings : • Test point : C39 ) (VT)
• Adjustment location : L006
Method : Set to FM 108.0MHz and adjust L006 so that the test
point becomes 6.0V± 0.1V.
5. FM Tracking Adjustment
L005 ................................................ 98MHz
6. LW VT Adjustment <EZ, K>
Settings : • Test point : C39 ) (VT)
• Adjustment location : L051
Method : Set to LW 288kHz and adjust L051 so that the test point
becomes 4.5V± 0.1V.
< DECK SECTION >
8. Bias Frequency Adjustment
Settings : • Test tape : TTA-602
• Test point : L801 pin 1
• Adjustment location : L801
Method :
L801 .....................................85kHz ± 2kHz
9. Tape Speed Adjustment
Settings : • Test tape : TTA-100
• Test point : PHONES JACK (J201)
• Adjustment location : SFR of deck motor
Method : Play back the test tape and adjust SFR so that the output
frequency is 3000Hz + 90Hz/-60Hz.
10. Azimuth Adjustment
Settings : • Test tape : TTA-320
• Test point : PHONES JACK (J201)
• Adjustment location : Azimuth adjustment screw
Method : Play back the test tape and adjust the screw so that the
output is maximum.
< CD SECTION >
11. Focus Bias Adjustment
Settings : • Test point : IC401 PIN58 (VREF), IC401 PIN20 (FE)
• Adjustment location : SFR430
• Test disc : TCD-782 (YEDS-18) second track
Method : Play back the disc and adjust SFR430 so that the voltage
between the test point becomes 0~-10mV.
7. LW Tracking Adjustment <EZ, K>
L003 (2/2) ....................................... 153kHz
TC051 .............................................288kHz
– 32 –
MECHANICAL EXPLODED VIEW 1 / 1
22
20
19
18
17
16
G
6
A
47
A
21
25
DA11T3C
26
23
11
J
PWB
31
33
38
C
32
30
E
29
37
PWB
39
34
B
I
H
35
D
B
36
A
C
15
A
8
5
9
48
4
2
14
A
12
LCD601
27
PWB
11
ZZM-1
AR5NC
A
13
C
28
10
A
7
24
45
44
43
K
46
A
A
42
41
F
40
A
PLATE,ANT
PLATE,PT
PWB
PWB
PWB
PWB
PWB
A
1
3
A
6
A
– 33 –
MECHANICAL PARTS LIST 1 / 1
PART NO.
NO.
1 8B-CDA-113-010 WINDOW,CASS (R)<[R]24EZ>
1 8B-CDA-009-010 WINDOW,CASS<[S]24EZ,[S]24K,[S]26U,[W]27U>
1 8B-CDA-093-010 WINDOW,CASS (G)<[G]24EZ>
1 8B-CDA-073-010 WINDOW,CASS (L)<[L]28U>
2 8B-CDA-003-010 LID,CASS<EXCEPT [W]27U>
2 8B-CDA-132-010 LID,CASS U (W)<[W]27U>
3 8A-CDA-212-010 SPR-T,CASS
4 8B-CHA-025-010 WINDOW,DISP EZ G<[G]24EZ>
4 8B-CHA-012-010 WINDOW,DISP EZ K<[S]24EZ,[S]24K>
4 8B-CHA-026-010 WINDOW,DISP EZ R<[R]24EZ>
4 8B-CHA-015-010 WINDOW,DISP U<[S]26U,[W]27U>
4 8B-CDA-138-010 WINDOW,DISP U (L)<[L]28U>
5 8B-CHA-023-010 CABI ASSY,FRONT EZ G<[G]24EZ>
5 8B-CHA-005-010 CABI ASSY,FRONT EZ K<[S]24EZ,[S]24K>
5 8B-CHA-024-010 CABI ASSY,FRONT EZ R<[R]24EZ>
5 8B-CHA-014-010 CABI ASSY,FRONT U<[S]26U>
5 8B-CHA-019-010 CABI ASSY,FRONT U L<[L]28U>
5 8B-CHA-016-010 CABI ASSY,FRONT U W<[W]27U>
6 8B-CDA-615-010 SPKR,10 7OHM
7 8B-CDA-020-010 KEY,STOP<[S]24EZ,[S]24K,[S]26U,[W]27U>
7 8B-CDA-096-010 KEY,STOP (G)<[G]24EZ>
7 8B-CDA-077-010 KEY,STOP (L)<[L]28U>
7 8B-CDA-116-010 KEY,STOP (R)<[R]24EZ>
8 8B-CDA-015-010 KEY,FUNC A<[S]26U,[W]27U,[L]28U>
8 8B-CDA-017-010 KEY,FUNC C<[S]24EZ,[S]24K>
8 8B-CHA-030-010 KEY,FUNC F<[G]24EZ,[R]24EZ>
9 8B-CDA-014-010 KEY,CD
10 8B-CDA-019-010 KEY,PAUSE<[S]24EZ,[S]24K,[S]26U,[W]27U>
10 8B-CDA-095-010 KEY,PAUSE (G)<[G]24EZ>
10 8B-CDA-076-010 KEY,PAUSE (L)<[L]28U>
10 8B-CDA-115-010 KEY,PAUSE (R)<[R]24EZ>
11 87-063-165-010 OIL-DMPR 150
12 8B-CHA-201-010 HLDR,LCD
13 8B-CDA-622-010 FF-CABLE,8P CD-FR
14 8B-CDA-620-010 FF-CABLE,16P FR-MAIN
15 8B-CDL-008-010 PANEL,TOP<[S]24EZ,[S]24K,[S]26U,[W]27U>
15 8B-CDA-106-010 PANEL,TOP G<[G]24EZ>
15 8B-CDA-107-010 PANEL,TOP R<[R]24EZ>
15 8B-CDA-136-010 PANEL,TOP U (L)<[L]28U>
16 8Z-CT6-213-110 BASE,CHUCK
17 8Z-CT6-214-110 RING,CHUCK
18 87-036-368-010 MAGNET
19 86-CT9-217-110 HLDR,CHUCK A(S)
20 8B-CDA-006-010 LID,CD<[S]24EZ,[S]24K,[S]26U,[W]27U>
20 8B-CDA-104-010 LID,CD G<[G]24EZ>
20 8B-CDA-105-010 LID,CD R<[R]24EZ>
20 8B-CDA-135-010 LID,CD U (L)<[L]28U>
21 8B-CDA-005-010 CHAS,CD<EXCEPT [W]27U>
21 8B-CDA-063-010 CHAS,CD (W)<[W]27U>
22 87-036-389-010 SW,PUSH LOCK
23 8A-CDA-211-010 SPR-T,CD
24 8B-CDA-021-010 KEY,FF<[S]24EZ,[S]24K,[S]26U,[W]27U>
24 8B-CDA-097-010 KEY,FF (G)<[G]24EZ>
24 8B-CDA-078-010 KEY,FF (L)<[L]28U>
24 8B-CDA-117-010 KEY,FF (R)<[R]24EZ>
25 8Z-CDB-169-010 PANEL,CD SANYO
26 8B-CDA-621-010 FF-CABLE,16P CD-RF
27 88-CH6-220-010 CUSHION,CD A
28 8B-CDA-630-010 CONN ASSY,4P RPH
29 8B-CDA-631-010 CONN ASSY,4P TA-ME
30 8B-CDA-633-010 CONN ASSY,4P SP
31 8B-CDA-626-010 CONN ASSY,2P DOOR
32 8B-CDA-010-010 LID,HANDL<EXCEPT [W]27U>
32 8B-CHA-022-010 LID,HANDL W<[W]27U>
33 8B-CDA-007-010 HANDL,ARM<EXCEPT [W]27U>
33 8B-CHA-021-010 HANDL,ARM W<[W]27U>
34 8B-CDA-004-010 LID,BATT<EXCEPT [W]27U>
34 8B-CHA-020-010 LID,BATT W<[W]27U>
35 87-A91-857-010 ANT,ROD 5SEC709
36 8B-CHA-003-010 CABI,REAR<EXCEPT [W]27U>
DESCRIPTION REF. NO. KANRI
– 34 –
PART NO.
36 8B-CHA-018-010 CABI,REAR U W<[W]27U>
37 87-A60-178-010 JACK,AC E W/SW<EZ,K>
!
!
37 87-A60-177-010 JACK,AC U W/SW<U>
38 8Z-CD5-634-010 COVER,AC SOCKET
!
39 8A-CDA-612-010 PT,E 2.5W<EZ,K>
!
39 8A-CDA-611-010 PT,U 2.5W<U>
40 8B-CDA-202-010 HLDR,TU
41 8A-CDA-220-010 PLATE,REC
42 8A-CDA-221-010 SPR-P,REC
43 8B-CDA-024-010 KEY,REC<[S]24EZ,[S]24K,[S]26U,[W]27U>
43 8B-CDA-100-010 KEY,REC (G)<[G]24EZ>
43 8B-CDA-081-010 KEY,REC (L)<[L]28U>
43 8B-CDA-120-010 KEY,REC (R)<[R]24EZ>
44 8B-CDA-023-010 KEY,PLAY<[S]24EZ,[S]24K,[S]26U,[W]27U>
44 8B-CDA-099-010 KEY,PLAY (G)<[G]24EZ>
44 8B-CDA-080-010 KEY,PLAY (L)<[L]28U>
44 8B-CDA-119-010 KEY,PLAY (R)<[R]24EZ>
45 8B-CDA-022-010 KEY,REW<[S]24EZ,[S]24K,[S]26U,[W]27U>
45 8B-CDA-098-010 KEY,REW (G)<[G]24EZ>
45 8B-CDA-079-010 KEY,REW (L)<[L]28U>
45 8B-CDA-118-010 KEY,REW (R)<[R]24EZ>
46 87-064-185-010 HLDR,WIRE
47 86-CT9-222-010 PLATE,MAGNET
48 8B-CDA-016-010 KEY,FUNC B
A 87-721-096-410 QT2+3-10 GLD
B 87-751-104-410 VT2+3-30
C 87-751-076-410 SCREW 2.6-12
D 87-254-097-410 U+3-12 CR
E 8A-CK4-223-010 S-SCREW,CD
F 8A-CDA-222-010 S-SCREW,CASS+2.6-4
G 87-751-096-410 VT2+3-10 GLD
H 87-751-097-410 VT2+3-12 W/O SLOT
I 87-501-092-410 VF+3-4
J 87-721-074-410 QT2+2.6-8 W/O SLOT
K 87-751-096-410 VT2+3-10 W/O SLOT
NO.
DESCRIPTION REF. NO. KANRI
COLOR NAME TABLE
Basic color symbol Color Basic color symbol Color Basic color symbol Color
B Black C Cream D Orange
G Green H Gray L Blue
LT Transparent Blue N Gold P Pink
R Red S Silver ST Titan Silver
T Brown V Violet W White
WT Transparent White Y Yellow YT Transparent Yellow
LM Metallic Blue LL Light Blue GT Transparent Green
LD Dark Blue DT Transparent Orange GM Metallic Green
YM Metallic Yellow DM Metallic Orange PT Transparent Pink
LA Aqua Blue GL Light Green HT Transparent Gray
– 35 –
TAPE MECHANISM EXPLODED VIEW 1 / 1
12
11
TERMINAL,LB1
A
10
9
4
3
2
1
8
14
7
55
42
6
5
13
53
B
19
17
16
21
20
22
27
24
23
15
18
28
26
25
C
54
29
31
30
48
50
51
52
49
47
46
45
44
43
41
36
40
37
32
39
33
34
1
35
38
– 36 –
TAPE MECHANISM PARTS LIST 1 / 1
PART NO. DESCRIPTION REF. NO. KANRI
NO.
1 8Z-ZM1-254-310 SPR-C,REEL R
2 8Z-ZM1-225-110 GEAR,REEL R
3 8Z-ZM1-253-210 SPR-C,AUTO SENSOR
4 8Z-ZM1-217-110 LEVER,AUTO SENSOR
5 8Z-ZM1-212-110 LEVER,T-UP
6 8Z-ZM1-245-310 SPR-T,AUTO
7 8Z-ZM1-236-010 CLR,SLIP FF/REW
8 8Z-ZM1-252-110 SPR-C,FF/REW
9 8Z-ZM1-230-010 GEAR,SLIP FF/REW A
10 8Z-ZM1-269-010 FELT,FF/REW 2
11 8Z-ZM1-238-110 GEAR,SLIP FF/REW B 2
12 8Z-ZM1-237-110 LEVER,FF/REW 2
13 8Z-ZM1-283-010 LEVER,PAUSE 2
14 8Z-ZM1-222-010 LEVER,E-LOCK M
15 8Z-ZM1-219-010 LEVER,E-OPEN
16 8Z-ZM1-244-110 SPR-T,T-UP
17 8Z-ZM1-247-310 SPR-T,PINCH
18 8Z-ZM1-261-110 ROLLER ASSY,PINCH
19 8Z-ZM1-221-210 LEVER,PINCH
20 8Z-ZM1-205-310 LEVER,PLAY
21 8Z-ZM1-248-210 SPR-T,BRG
22 87-A92-207-010 HEAD,AP-4211T4
23 84-ZM2-227-310 SPR-C,AZIMUTH
24 8Z-ZM1-216-110 LEVER,AUTO
25 8Z-ZM1-246-110 SPR-T,AUTO 2
26 8Z-ZM1-233-110 GEAR,IDL REW
27 8Z-ZM1-208-010 LEVER,STOP
28 8Z-ZM1-207-010 LEVER,FF
29 8Z-ZM1-206-010 LEVER,REW
30 8Z-ZM1-211-210 LEVER,REC 2
DESCRIPTION REF. NO. KANRI
PART NO.
NO.
31 87-A91-819-010 HEAD,EH 2NSS-2200
32 8Z-ZM1-215-010 LEVER,REC LOCK
33 87-A91-492-010 SW,LEAF MSW18560
34 8Z-ZM1-226-010 GEAR,REEL L
35 8Z-ZM1-241-210 SPR-T,PLAY
36 8Z-ZM1-220-110 LEVER,REC SENSOR
37 8Z-ZM1-249-210 SPR-T,FR
38 8Z-ZM1-242-310 SPR-T,FF/REW
39 8Z-ZM3-244-010 GEAR,CAM TD20
40 8Z-ZM1-232-010 GEAR,IDL FF/REW
41 82-ZM1-290-010 FLY-WHL ASSY,ZZM1
42 8Z-ZM1-275-010 W-L,1.47-4-0.25
43 8Z-ZM1-228-010 GEAR,SLIP T-UP B
44 8Z-ZM1-265-010 FELT,T-UP
45 8Z-ZM1-227-010 GEAR,SLIP T-UP A
46 8Z-ZM1-251-210 SPR-C,T-UP SLIP
47 8Z-ZM1-243-310 SPR-T,STOP/PAUSE
48 87-A91-825-010 MOT,M09Y/Z
49 8Z-ZM1-271-010 PULLEY,MOT ZZM-1
50 8Z-ZM1-264-010 BELT,MAIN S
51 8Z-ZM1-260-010 SPR-P,CASETTE
52 8Z-ZM1-201-910 CHAS ASSY,ZZM-1
53 8Z-ZM1-255-310 SPR-T,E-LOCK
54 8Z-ZM1-214-210 LEVER,LOCK
55 8Z-ZM1-257-110 SPR-C,F/R
A 84-ZM2-242-010 S-SCREW,AZ1-2-6.4
B 8Z-ZM1-270-110 V+2.6 ZZM-1
C 87-B10-301-010 W-L,1.63-3.2-0.5 SLIT
– 37 –
CD MECHANISM EXPLODED VIEW 1 / 1
1
SW1
A
2
3
4
CD MOTOR C.B
PIN 3
CD MECHANISM PARTS LIST 1 / 1
PART NO.
NO.
1 M8-ZZK-E90-070 DA11T3C
2 S2-121-A28-400 COVER GEAR
3 S2-511-A21-000 GEAR MIDDLE
4 S2-511-A21-100 GEAR DRIVE
A S1-PN2-03R-OSE SCR PAN PCS 2-3
DESCRIPTION REF. NO. KANRI
M2
(SLED MOTOR)
– 38 –
2–11, IKENOHATA 1–CHOME, TAITO-KU, TOKYO 110, JAPAN TEL:03 (3827) 3111
Printed in Singapore 9820543 2000045 0251431