How it Works
Aiwa
Loading...
CSD A310
Schematic
1 pgs29.41 Kb0
Schematic
36 pgs3.42 Mb0
Service Manual
21 pgs3.03 Mb0
Service Manual
5 pgs266.89 Kb0
Service Manual
14 pgs937.75 Kb0
Service Manual
31 pgs3.83 Mb0
Service Manual
31 pgs3.8 Mb0
Service Manual
14 pgs721.48 Kb0
Service Manual
8 pgs419.82 Kb0

Aiwa CSD-A310 Service Manual

Download
Page 1
CSD-A310
HC, EZ, G
SERVICE MANUAL
COMPACT DISC STEREO
RADIO CASSETTE RECORDER
BASIC TAPE MECHANISM : ZZM-1 AR4NC BASIC CD MECHANISM : DA11T3C
DATA
Page 2
SPECIFICATIONS
<Tuner section>
Frequency range FM: 87.5 MHz to 108.0 MHz
Antenna: Rod antenna (AM) MW: 530 kHz to 1,605 kHz Antenna: Ferrite bar antenna LW: <G, EZ> 150 kHz to 285 kHz Antenna: Ferrite bar antenna
<Deck section>
Track format 4 tracks, 2 channels Frequency range Normal tape: 50 - 12,500 Hz (EIAJ) Recording system AC bias Erasing system Magnet erase Heads Recording/playback head (1)
Erasure head (1)
<CD player section>
Disc Compact disc Scanning method Non-contact optical scanner
(semiconductor laser)
<General>
Speaker 80 mm cone type (2) Outputs Headphones jack: stereo mini-jack Power output 2.9 W + 2.9 W<EZ>
(DIN MUSIC POWER)
2.5 W + 2.5 W (EIAJ 7 ohms, T.H.D. 10 % DC)
1.9 W + 1.9 W (DIN 1% Rated Power)
Power requirements DC 12 V using eight size C (R14)
batteries AC 110 - 120 V/220 - 240 V, switchable, 50/60 Hz<HR, HT> AC 230 V, 50 Hz <G, EZ>
Power consumption 16 W Dimensions 310 x 171 x 260 mm (W x H x D) Weight 2.8 kg (excluding batteries)
• Design and specifications are subject to change without notice.
– 2 –
Page 3
Solder
PROTECTION OF EYES FROM LASER BEAM DURING SERVICING
This set employs laser. Therefore, be sure to follow carefully the instructions below when servicing.
WARNING!!
WHEN SERVICING, DO NOT APPROACH THE LASER EXIT WITH THE EYE TOO CLOSELY. IN CASE IT IS NECESSARY TO CONFIRM LASER BEAM EMISSION. BE SURE TO OBSERVE FROM A DISTANCE OF MORE THAN 30cm FROM THE SURFACE OF THE OBJEC­TIVE LENS ON THE OPTICAL PICK-UP BLOCK.
s Caution: Invisible laser radiation when
open and interlocks defeated avoid exposure to beam.
s Advarsel: Usynlig laserståling ved åbning,
når sikkerhedsafbrydere er ude af funktion. Undgå udsættelse for stråling.
VAROITUS!
Laiteen Käyttäminen muulla kuin tässä käyttöohjeessa mainitulla tavalla saataa altistaa käyt-täjän turvallisuusluokan 1 ylittävälle näkymättöm ä lle lasersäteilylle.
VARNING!
Om apparaten används på annat sätt än vad som specificeras i denna bruksanvising, kan användaren utsättas för osynling laserstrålning, som överskrider gränsen för laserklass 1.
CAUTION
Use of controls or adjustments or performance of proce­dures other than those specified herin may result in hazardous radiation exposure.
ATTENTION
L’utillisation de commandes, réglages ou procédures autres que ceux spécifiés peut entraîner une dangereuse exposition aux radiations.
ADVARSEL
Usynlig laserståling ved åbning, når sikkerhedsafbrydereer ude af funktion. Undgå udsættelse for stråling.
This Compact Disc player is classified as a CLASS 1 LASER product. The CLASS 1 LASER PRODUCT label is located on the rear exterior.
CLASS 1 LASER PRODUCT KLASSE 1 LASER PRODUKT LUOKAN 1 LASER LAITE KLASS 1 LASER APPARAT
Precaution to replace Optical block
(SF-P101NR)
Body or clothes electrostatic potential could ruin laser diode in the optical block. Be sure ground body and workbench, and use care the clothes do not touch the diode.
1) After the connection, remove solder shown in right figure.
PICK-UP Assy P.C.B
– 3 –
Page 4
ELECTRICAL MAIN PARTS LIST
PART NO. DESCRIPTIONREF. NO. KANRI
NO.
IC
87-A20-955-010 IC,LA1828 87-A21-064-010 IC,LA4227 87-A21-520-040 C-IC,M61509FP 87-A20-446-010 C-IC,LA9241ML 87-A20-459-010 C-IC,LC78622ED
87-A21-093-010 IC,LA6541D 8A-CD9-610-010 C-IC,LC865516A-5P16 87-A21-607-010 IC,NJM14558LD
TRANSISTOR
89-327-143-080 TR,2SC2714 (0.1W) 87-026-447-080 TR,2SC1740S R 87-026-463-080 TR,2SA933S (0.3W) 87-A30-288-040 CHIP-TR,DTC114YKA 89-320-011-080 TR,2SC2001 (15W)
89-112-965-080 TR,2SA1296 (0.75W) 87-026-291-080 TR,DTC124XS 87-A30-226-010 TR,2SB1655E 87-026-462-080 TR,2SC1740 S(RS 0.3W) 89-318-154-080 TR,2SC1815 (0.4W)
89-109-332-380 TR,2SA933RS 89-113-187-080 TR,2SA1318TU 87-A30-287-040 TR,DTC114TKA (0.2W) 89-317-403-080 TR,2SC1740S 87-026-464-010 TR,DTC114TS
87-026-464-080 TR,DTC114TS (0.3W)
DIODE
87-020-465-080 DIODE,1SS133 (110MA) 87-027-607-080 ZENER,HZ7B3L 87-A40-466-080 ZENER,MTZJ2.7A 87-070-345-080 DIODE,IN4148 87-A40-648-080 ZENER,MTZJ8.2A
87-A40-234-080 ZENER,MTZJ5.6A 87-017-978-080 DIODE,1N4003 87-017-932-080 ZENER,MTZJ6.2B 87-A40-465-010 DIODE,FR202
MAIN C.B
C30 87-010-260-080 CAP, ELECT 47-25V C211 87-010-805-080 CAP, S 1-16 C212 87-010-805-080 CAP, S 1-16 C215 87-016-460-080 C-CAP,S 0.22-16 B C216 87-016-460-080 C-CAP,S 0.22-16 B
C231 87-010-213-080 C-CAP,S 0.015-50 B C232 87-010-213-080 C-CAP,S 0.015-50 B C233 87-A10-201-080 C-CAP,S0.33-16 KB C234 87-A10-201-080 C-CAP,S0.33-16 KB C235 87-016-669-080 C-CAP,S 0.1-25 K B
C236 87-016-669-080 C-CAP,S 0.1-25 K B C237 87-010-408-080 CAP, ELECT 47-50V C239 87-010-197-080 CAP, CHIP 0.01 DM C240 87-010-197-080 CAP, CHIP 0.01 DM C247 87-010-401-080 CAP, ELECT 1-50V
C248 87-010-401-080 CAP, ELECT 1-50V C251 87-010-401-080 CAP, ELECT 1-50V C263 87-010-178-080 CHIP CAP 1000P C264 87-010-178-080 CHIP CAP 1000P C265 87-010-263-080 CAP, ELECT 100-10V
C266 87-010-263-080 CAP, ELECT 100-10V C267 87-010-112-080 CAP, ELECT 100-16V C268 87-010-112-080 CAP, ELECT 100-16V C271 87-010-235-080 CAP,E 470-16 SME C272 87-010-235-080 CAP,E 470-16 SME
C278 87-010-405-080 CAP, ELECT 10-50V
DESCRIPTIONREF. NO. KANRI
PART NO.
NO.
C279 87-010-385-080 CAP, ELECT 220-25V C301 87-016-658-000 CAP,E 4700-35 M SMG C306 87-010-404-080 CAP, ELECT 4.7-50V C307 87-010-401-080 CAP, ELECT 1-50V C308 87-010-221-080 CAP, ELECT 470-10V
C309 87-010-197-080 CAP, CHIP 0.01 DM C310 87-010-248-080 CAP, ELECT 220-10V C311 87-010-374-080 CAP, ELECT 47-10V C312 87-010-385-080 CAP, ELECT 220-25V C316 87-010-384-080 CAP, ELECT 100-25V
C321 87-010-197-080 CAP, CHIP 0.01 DM C322 87-010-263-080 CAP, ELECT 100-10V C325 87-010-405-080 CAP, ELECT 10-50V C401 87-010-403-080 CAP, ELECT 3.3-50V C402 87-010-197-080 CAP, CHIP 0.01 DM
C403 87-010-263-080 CAP, ELECT 100-10V C404 87-010-248-080 CAP, ELECT 220-10V C405 87-010-197-080 CAP, CHIP 0.01 DM C406 87-010-374-080 CAP, ELECT 47-10V C407 87-010-178-080 CHIP CAP 1000P
C408 87-010-198-080 CAP, CHIP 0.022 C409 87-010-248-080 CAP, ELECT 220-10V C410 87-010-263-080 CAP, ELECT 100-10V C411 87-A11-177-080 C-CAP,S 0.15-16 K B C412 87-010-401-080 CAP, ELECT 1-50V
C413 87-016-369-080 C-CAP,S 0.033-25 B K C414 87-010-405-080 CAP, ELECT 10-50V C416 87-010-545-080 CAP, ELECT 0.22-50V C417 87-012-157-080 C-CAP,S 330P-50 CH C418 87-010-213-080 C-CAP,S 0.015-50 B
C419 87-A11-608-080 C-CAP,S 0.33-25 K B C420 87-016-369-080 C-CAP,S 0.033-25 B K C421 87-A11-177-080 C-CAP,S 0.15-16 K B C422 87-010-183-080 C-CAP,S 2700P-50 B C423 87-010-956-080 CHIP-CAP,S 0.068-25B
C424 87-010-993-080 C-CAP,S 0.056-25 B C425 87-010-176-080 C-CAP,S 680P-50 SL C426 87-A11-608-080 C-CAP,S 0.33-25 K B C428 87-010-197-080 CAP, CHIP 0.01 DM C429 87-010-186-080 CAP,CHIP 4700P
C430 87-012-156-080 C-CAP,S 220P-50 CH C431 87-010-545-080 CAP, ELECT 0.22-50V C432 87-010-374-080 CAP, ELECT 47-10V C433 87-010-401-080 CAP, ELECT 1-50V C434 87-010-184-080 CHIP CAPACITOR 3300P(K)
C435 87-010-197-080 CAP, CHIP 0.01 DM C436 87-010-374-080 CAP, ELECT 47-10V C437 87-010-404-080 CAP, ELECT 4.7-50V C438 87-016-669-080 C-CAP,S 0.1-25 K B C439 87-010-178-080 CHIP CAP 1000P
C440 87-010-145-080 C-CAP,S 1P-50 CH C441 87-010-197-080 CAP, CHIP 0.01 DM C442 87-010-312-080 C-CAP,S 15P-50 CH C445 87-012-368-080 C-CAP,S 0.1-50 F C446 87-012-368-080 C-CAP,S 0.1-50 F
C447 87-012-368-080 C-CAP,S 0.1-50 F C448 87-010-315-080 C-CAP,S 27P-50 CH C450 87-012-140-080 CAP 470P C451 87-012-156-080 C-CAP,S 220P-50 CH C455 87-010-247-080 CAP, ELECT 100-50V
C457 87-010-312-080 C-CAP,S 15P-50 CH C458 87-010-312-080 C-CAP,S 15P-50 CH C459 87-010-263-080 CAP, ELECT 100-10V C460 87-015-819-080 CAPACITOR,0.01 C461 87-010-197-080 CAP, CHIP 0.01 DM
C462 87-010-248-080 CAP, ELECT 220-10V C463 87-010-190-080 S CHIP F 0.01 C465 87-010-404-080 CAP, ELECT 4.7-50V C466 87-012-368-080 C-CAP,S 0.1-50 F C467 87-010-263-080 CAP, ELECT 100-10V
– 4 –
Page 5
PART NO. DESCRIPTIONREF. NO. KANRI
NO.
C469 87-012-154-080 C-CAP,S 150P-50 CH C470 87-010-544-080 CAP, ELECT 0.1-50V C471 87-015-785-080 CHIP CAPACITOR, 0.1FZ-25Z C472 87-015-785-080 CHIP CAPACITOR, 0.1FZ-25Z C473 87-015-785-080 CHIP CAPACITOR, 0.1FZ-25Z
C474 87-015-785-080 CHIP CAPACITOR, 0.1FZ-25Z C475 87-010-197-080 CAP, CHIP 0.01 DM C476 87-010-236-080 CAP,E 1000-10 SME C477 87-010-197-080 CAP, CHIP 0.01 DM C478 87-010-263-080 CAP, ELECT 100-10V
C479 87-010-197-080 CAP, CHIP 0.01 DM C480 87-010-221-080 CAP, ELECT 470-10V C481 87-010-405-080 CAP, ELECT 10-50V C482 87-010-405-080 CAP, ELECT 10-50V C489 87-012-368-080 C-CAP,S 0.1-50 F
C490 87-012-368-080 C-CAP,S 0.1-50 F C491 87-010-197-080 CAP, CHIP 0.01 DM C492 87-010-221-080 CAP, ELECT 470-10V C494 87-010-190-080 S CHIP F 0.01 C501 87-012-368-080 C-CAP,S 0.1-50 F
C502 87-010-322-080 C-CAP,S 100P-50 CH C503 87-010-322-080 C-CAP,S 100P-50 CH C504 87-010-322-080 C-CAP,S 100P-50 CH C505 87-010-322-080 C-CAP,S 100P-50 CH C506 87-010-322-080 C-CAP,S 100P-50 CH
C510 87-016-669-080 C-CAP,S 0.1-25 K B C801 87-010-248-080 CAP, ELECT 220-10V C805 87-012-365-080 C-CAP,S 0.027-25VBK C806 87-012-365-080 C-CAP,S 0.027-25VBK C807 87-010-405-080 CAP, ELECT 10-50V
C808 87-010-405-080 CAP, ELECT 10-50V C809 87-010-405-080 CAP, ELECT 10-50V C810 87-010-405-080 CAP, ELECT 10-50V C811 87-010-178-080 CHIP CAP 1000P C812 87-010-178-080 CHIP CAP 1000P
C816 87-010-180-080 C-CER 1500P C817 87-010-180-080 C-CER 1500P C819 87-010-426-080 C-CAP,S 0.012-25 B C820 87-010-426-080 C-CAP,S 0.012-25 B C821 87-010-401-080 CAP, ELECT 1-50V
C822 87-010-401-080 CAP, ELECT 1-50V C823 87-010-181-080 CAP,CHIP S 1800P C824 87-010-181-080 CAP,CHIP S 1800P C829 87-010-178-080 CHIP CAP 1000P C830 87-010-178-080 CHIP CAP 1000P
C831 87-010-198-080 CAP, CHIP 0.022 C833 87-018-195-080 CAP, CER 1200P-16V C834 87-010-248-080 CAP, ELECT 220-10V C835 87-010-322-080 C-CAP,S 100P-50 CH C836 87-010-322-080 C-CAP,S 100P-50 CH
C843 87-010-197-080 CAP, CHIP 0.01 DM C844 87-018-124-080 CAP, CER 270P-50V C845 87-010-178-080 CHIP CAP 1000P C846 87-010-263-080 CAP, ELECT 100-10V C851 87-010-186-080 CAP,CHIP 4700P
C852 87-010-178-080 CHIP CAP 1000P C853 87-018-211-080 CAP,TC U 0.01-50 Z F CN201 87-099-018-010 CONN,16P CN202 87-A60-685-010 CONN,4P H WHT EH CN205 87-A60-109-010 CONN,2P V S2M-2W
CN301 87-099-416-010 CONN,3P EH H WHT CN401 87-A60-424-010 CONN,16P V TOC-B CN403 87-099-201-010 CONN,8P 6216 H CN801 87-A60-110-010 CONN,4P V S2M-4W CN802 87-049-469-010 CONN,4P V
CNA205 8A-CD9-626-010 CONN ASSY,2P DOOR CNA302 8A-CDB-627-010 CONN ASSY,6P MA-TUNER CNA402 8A-CDB-622-010 CONN ASSY,6P CD-MOTOR CNA801 8A-CDB-626-010 CONN ASSY,4P CASS HEAD CNA802 8A-CDB-625-010 CONN ASSY,4P CASS MECHA
DESCRIPTIONREF. NO. KANRI
PART NO.
NO.
FC401 8A-CDB-623-010 FF-CABLE, 16P 1.0 CD-RF L401 87-003-102-080 COIL, 10UH L404 87-003-152-080 COIL, 100UH L801 87-007-342-010 COIL,OSC 85K BIAS R840 87-029-124-010 RES,FUSE 2.2-1/4
SFR430 87-024-437-080 SFR100K,RH063EC SW801 88-CT6-619-010 BACK SLIDE SW 6P2T SHORTIN X401 8Z-CD5-633-010 VIB, CER16.93MHZ FCR16.93M2
TUNER C.B
C1 87-010-314-080 C-CAP,S 22P-50V C2 87-010-316-080 C-CAP,S 33P-50 CH C3 87-010-314-080 C-CAP,S 22P-50V C4 87-010-148-080 CAP, CHIP S 75P SL<HC> C5 87-010-378-080 CAP, ELECT 10-16V
C7 87-012-156-080 C-CAP,S 220P-50 CH C8 87-010-197-080 CAP, CHIP 0.01 DM C9 87-010-311-080 CAP 12P C10 87-010-197-080 CAP, CHIP 0.01 DM C11 87-010-152-080 C-CAP,S 8P-50 CH
C12 87-010-314-080 C-CAP,S 22P-50V C13 87-010-322-080 C-CAP,S 100P-50 CH C14 87-010-148-080 CAP, CHIP S 75P SL C15 87-016-669-080 C-CAP,S 0.1-25 K B C16 87-010-178-080 CHIP CAP 1000P
C17 87-016-669-080 C-CAP,S 0.1-25 K B C18 87-010-198-080 CAP, CHIP 0.022 C19 87-016-669-080 C-CAP,S 0.1-25 K B C20 87-010-400-080 CAP, ELECT 0.47-50V C21 87-010-403-080 CAP, ELECT 3.3-50V
C22 87-010-197-080 CAP, CHIP 0.01 DM C24 87-010-188-080 CAP,CHIP 6800P C25 87-010-188-080 CAP,CHIP 6800P C26 87-016-669-080 C-CAP,S 0.1-25 K B C27 87-016-669-080 C-CAP,S 0.1-25 K B
C28 87-010-992-080 C-CAP,S 0.047-25 B C29 87-010-992-080 C-CAP,S 0.047-25 B C30 87-010-248-080 CAP, ELECT 220-10V C31 87-010-379-080 CAP, ELECT 22-16V C32 87-010-197-080 CAP, CHIP 0.01 DM
C33 87-010-197-080 CAP, CHIP 0.01 DM C34 87-010-197-080 CAP, CHIP 0.01 DM C35 87-010-197-080 CAP, CHIP 0.01 DM C36 87-010-263-080 CAP, ELECT 100-10V C37 87-010-197-080 CAP, CHIP 0.01 DM
C38 87-010-197-080 CAP, CHIP 0.01 DM C41 87-010-318-080 C-CAP,S 47P-50 CH<EZ,G> C44 87-010-302-080 C-CAP,S 270P-50 CH<EZ,G> C51 87-010-197-080 CAP, CHIP 0.01 DM C56 87-010-152-080 C-CAP,S 8P-50 CH<HC>
CF1 87-A90-128-010 FLTR,AM IF CFAL-455 CF2 82-785-747-010 CF MS2 GHY R CF3 82-785-747-010 CF MS2 GHY R CN2 87-099-194-010 CONN,6P 6216V D3 87-A40-916-040 C-VARI-CAP,HVC202A
L2 87-A50-560-010 COIL,FM BPF(ACD) L3 8A-CD9-660-010 BAR-ANT,MW 2B-ACD(COI)<HC> L3 8A-CD9-661-010 BAR-ANT,MW/LW 3B-ACD(COI)<EZ,G> L4 87-A50-562-010 COIL,FM RF EX(ACD) L5 87-A50-564-010 COIL,FM OSC EX(ACD)
L6 87-A50-337-010 COIL,AM OSC (TOKO)<HC> L7 87-A50-336-010 COIL,AM IFT (TOKO) L8 87-A50-335-010 COIL,FM IFT (TOKO) L9 87-A50-334-010 COIL,FM DET (TOKO) L10 87-005-849-080 COIL,10UH(CECS)
L16 87-A50-569-010 COIL,LW OSC-ACD(COI)<EZ,G> L17 87-A50-337-010 COIL,AM OSC (TOKO)<EZ,G> S1 87-A91-549-010 SW,SL-6-4 SK64D01G06<EZ,G> SW1 87-A91-548-010 SW,SL-2-3 SK23E01G06<HC>
– 5 –
Page 6
PART NO. DESCRIPTIONREF. NO. KANRI
DESCRIPTIONREF. NO. KANRI
NO.
TC5 87-011-221-080 TRIMMER,CER 30P 6.15X5.9 VC<EZ,G>
VOL C.B TC6 87-011-221-080 TRIMMER,CER 30P 6.15X5.9 VC<EZ,G> VC1 87-A91-635-010 TUN-CAP,20P-140P E-ACD(MITSUMI
CN607 84-722-632-010 CONN,2P H
S614 8Z-CT6-636-010 SW,TACT EVQJAC04M
S615 8Z-CT6-636-010 SW,TACT EVQJAC04M FRONT C.B
C601 87-010-313-080 CAP, CHIP 18P
PHONE C.B C602 87-010-315-080 C-CAP,S 27P-50 CH C603 87-010-319-080 C-CAP,S 56P-50 CH C604 87-010-317-010 CHIP CAP,S 39P CH C605 87-010-263-080 CAP, ELECT 100-10V
CN204 87-049-469-010 CONN,4P V
CNA203 8A-CDB-624-010 CONN ASSY,3P H.P
CNA204 8A-CDB-633-010 CONN ASSY,4P SPKR
J251 87-009-216-010 JACK, DIA 3.5 C606 87-015-785-080 CHIP CAPACITOR, 0.1FZ-25Z C607 87-015-819-080 CAPACITOR,0.01 C608 87-010-405-080 CAP, ELECT 10-50V
BATT A C.B C609 87-010-400-080 CAP, ELECT 0.47-50V C611 87-010-248-080 CAP, ELECT 220-10V
C901 87-018-205-080 CAP, CERA-SOL 0.022
C902 87-018-205-080 CAP, CERA-SOL 0.022 C613 87-012-368-080 C-CAP,S 0.1-50 F C614 87-010-312-080 C-CAP,S 15P-50 CH CN601 87-099-033-010 16P 6216 H CN602 87-099-201-010 CONN,8P 6216 H CNA604 8A-CDB-616-010 CONN ASSY,6P KEY FUNCT
CNA606 8A-CDB-617-010 CONN ASSY,2P KEY VOL
C903 87-018-205-080 CAP, CERA-SOL 0.022
C904 87-018-205-080 CAP, CERA-SOL 0.022
CNA901 8A-CDB-621-010 CONN ASSY,3P POWER
!
PR901 87-A90-092-080 PROTECTOR,2.5A 491
!
PT901 8A-CDB-653-010 PT,E 2.5W EI48X23<EZ,G>
!
PT901 8A-CDB-651-010 PT,H 2.5W EI48X23<HC> FC601 8A-CDB-618-010 FF-CABLE, 16P 1.25 FR-MAIN FC602 8A-CDB-619-010 FF-CABLE, 8P 1.25 CD-FR L601 87-003-102-080 COIL, 10UH
BATT B C.B LED602 88-CD6-630-010 LED,934ID RED
LED608 88-CD6-630-010 LED,934ID RED
CD MOTOR C.B LED611 87-CD8-616-010 LED,SA36-11 HWA-11.0 S601 8Z-CT6-636-010 SW,TACT EVQJAC04M S602 8Z-CT6-636-010 SW,TACT EVQJAC04M S603 8Z-CT6-636-010 SW,TACT EVQJAC04M
M2 9X-262-576-910 MOTOR GEAR ASSY
PIN3 91-564-722-110 CONNECTOR 6P
SW1 91-572-085-120 LEAF SW
S604 8Z-CT6-636-010 SW,TACT EVQJAC04M S605 8Z-CT6-636-010 SW,TACT EVQJAC04M X601 87-030-273-010 VIB,XTAL 32.768K5PPM X602 87-030-376-080 VIB,CER CSA5.76MG200
PART NO.
NO.
KEY FUNCT C.B
CN605 87-099-417-010 CONN 6P EH H WHT LED606 88-CD6-630-010 LED,934ID RED LED607 88-CD6-630-010 LED,934ID RED LED610 88-CD6-631-010 LED,934GD GRN S606 8Z-CT6-636-010 SW,TACT EVQJAC04M
S607 8Z-CT6-636-010 SW,TACT EVQJAC04M S608 8Z-CT6-636-010 SW,TACT EVQJAC04M S609 8Z-CT6-636-010 SW,TACT EVQJAC04M S611 8Z-CT6-636-010 SW,TACT EVQJAC04M
– 6 –
Page 7
CHIP RESISTOR PART CODE
Chip Resistor Part Coding
88
A
Resistor Code
Chip resistor
Wattage Type Tolerance 1/16W 1005 5% CJ
1/16W 1/10W
1/8W
1608 2125
3216
5% 5%
5%
TRANSISTOR ILLUSTRATION
Symbol
CJ CJ
CJ
Figure
Value of resistor
Form
L
Dimensions (mm)
t
W
0.55
B
E
Resistor Code
108 118
128
C
LW t
1.0 0.5 0.35 104
1.6 0.8 0.45 2 1.25 0.45
3.2
1.6
: A : A
E C B
2SA1296 2SC1815
B C E
2SB1655E
E C B
2SC2001 2SA1318TU
E C B
2SC1740S/SR/SRS 2SA933S/RS DTC124XS DTC114TS
DTC114YKA DTC114TKA 2SC2714
– 7 –
Page 8
WIRING – 1 (MAIN)
101112131415161718192021222324
1234567892526272829303132
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
– 8 –
R
S
T
U
Page 9
WIRING – 2 (BATT A / BATT B)
101112131415161718192021222324
1234567892526272829303132
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
– 9 –
R
S
T
U
Page 10
SCHEMATIC DIAGRAM – 1 (MAIN 1 / 2 / PHONE / BATT A / BATT B)
– 10 –
Page 11
SCHEMATIC DIAGRAM – 2 (MAIN 2 / 2 / CD MOTOR)
– 11 –
Page 12
WIRING – 3 (TUNER) <HC>
101112131415161718192021222324
1234567892526272829303132
A
B
C
D
E
F
G
H
VC001 TUNING
I
J
K
L
M
N
O
P
Q
– 12 –
R
S
T
U
Page 13
SCHEMATIC DIAGRAM – 3 (TUNER) <HC>
– 13 –
Page 14
WIRING – 4 (TUNER) <EZ, G>
101112131415161718192021222324
1234567892526272829303132
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
– 14 –
VC001 TUNING
R
S
T
U
Page 15
SCHEMATIC DIAGRAM – 4 (TUNER) <EZ, G>
– 15 –
Page 16
WIRING – 5 (FRONT / KEY FUNCT / VOL / PHONE)
101112131415161718192021222324
1234567892526272829303132
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
– 16 –
R
S
T
U
Page 17
SCHEMATIC DIAGRAM – 5 (FRONT / KEY FUNCT / VOL)
– 17 –
Page 18
WIRING – 6 (CD MOTOR)
123456789101112131415
A
I CD MOTOR C.B
M2
+
(SLED MOTOR)
_
(INSIDE LIMIT SW)
6
SW1
PIN3
1
FROM A MAIN C.B CNA402
M2
SW1
M1
(SPINDLE MOTOR)
_
M1
B
C
D
E
F
G
+
H
I
J
PICK UP ASSY
SF-P101NR
16
1
FC401
K
L
M
N
O
P
Q
R
S
T
– 18 –
FROM A MAIN C.B CN401
U
Page 19
IC BLOCK DIAGRAM
– 19 –
Page 20
IC DESCRIPTION
IC, LC78622ED
Pin No.
1 DEFI I Defect detection signal (DEF) input. ("L" is applied when not used.) 2 TAI I For PLL/Test input. A pull-down resistor is incorporated. 3 PDO O Phase comparison output to control the external VCO. 4 VVSS – Ground of the built-in VCO. Normally, 0V. 5 ISET I For the connection of a resistor which adjusts the PDO output current. 6 VVDD – Power supply of the built-in VCO. 7 FR I Adjusts the VCO frequency range. 8 VSS – Ground of digital circuits. Normally, 0V.
9 EFMO O For slice level control/EFM signal output. 10 EFMIN I EFM signal input. 11 T2 I Test input. A pull-down resistor is incorporated. Be sure to connect this to 0V. 12 CLV+ 13 CLV-
14 V/P O
15 HFL I Track detection signal input. Schmitt trigger input. 16 TES I Track error signal input. Schmitt trigger input. 17 TOFF O Tracking off output.
Pin Name I/O
O Disc motor control tri-state outputs.
Output to monitor the automatic switching between the rough servo control and phase servo control. "H" :Rough servo, "L": Phase servo.
Description
18 TGL O Tracking gain switching output. "L" raises the gain. 19 JP+ 20 JP­21 PCK O Monitors the clock signal for EFM data playback.4.3218MHz when the phase is locked.
22 FSEQ O
23 VDD – Power supply of digital circuits. 24 SL+ I/O General purpose input/output 1. Controlled by serial data command issued by the microprocessor. 25 SL– I/O General purpose input/output 2. Controlled by serial data command issued by the microprocessor. 26 NC – Not connected. 27 PUIN I/O CD pickup inside limit switch. 28 RW I/O Serial data command sled signal output terminal from microprocessor. 29 EMPH O Deemphasis monitor. "H": when playing a deemphasis disc. (Not used) 30 C2F O C2 flag output. (Not used) 31 DOUT O Outputs a digital OUT signal. (EIAJ format) (Not used) 32 T3 33 T4 34 N.C – Not connected.
O Track jump control tri-state outputs.
Sync signal detection output. Goes "H" when the sync signal detected from the EFM signal matches the sync signal generated internally. (Not used)
I Test input. A pull-down resistor is incorporated. Be sure to connect this to 0V.
35 MUTEL O Lch 1-bit DAC/Lch muting output. (Not used)
– 20 –
Page 21
Pin No.
36 LVDD – Lch power supply. 37 LCHO O Lch output. 38 LVSS – Lch ground. Normally, 0V. 39 RVSS – Rch 1-bit DAC/Rch ground. Normally, 0V. 40 RCHO O Rch output. 41 RVDD – Rch power supply. 42 MUTER O Rch muting output. (Not used) 43 XVDD – Power supply of crystal oscillator. 44 XOUT O 45 XIN I 46 XVSS – Ground of crystal oscillator. Normally, 0V. 47 SBSY O Subcode block sync signal output. (Not used) 48 EFLG O C1,C2,single,duplex correction monitor. (Not used) 49 PW O Output of subcodes P,Q,R,S,T,U and W. (Not used) 50 SFSY O Subcode frame sync signal output. Falls when the subcode is set to the standby state.(No used) 51 SBCK I Subcode read-out clock input. Schmitt trigger input.("L" is applied when not used.) 52 FSX O 7.35 kHz sync signal output obtained by dividing the oscillator frequency. (Not used) 53 WRQ O Subcode Q standby output.
Pin Name
I/O Description
For the connection of a 16.9344 MHz crystal oscillator.
54 RWC I Read/write control input. Schmitt trigger input. 55 SQOUT O Subcode Q output. 56 COIN I Command input from the microprocessor.
57 CQCK I
58 RES I LC78622 reset input. 59 T11 O Test output. Set to open (normally, "L" output.) (Not used) 60 16M O 16.9344 MHz output. (Not used) 61 4.2M O 4.236 MHz output. 62 T5 I Test input. A pull-down resistor is incorporated. Be sure to connect to 0 V. 63 CS I Chip select input. A pull-down resistor is incorporated. 64 TEST1 I Test input with no pull-down resistor. Be sure to connect this to 0 V.
Command input retrieval clock or subcode retrieval clock input from SQOUT. Schmitt trigger input.
– 21 –
Page 22
IC, LA9241ML
Pin No.
1 FIN2 O
2 FIN1 O For the connection of the pickup photodiode.
3EO
4 F O For the connection of the pickup photodiode.
5 TB I Inputs the DC components in the TE signal.
6 TE– O
7 TE O TE signal output.
8 TESI I TES (track error sense) comparator input.The TE signal is passed through a BPF.
9 SCI I Shock detection input. 10 TH I Sets the time constant for the tracking gain. 11 TA O TA amp output. 12 TD– I Composes the tracking phase compensation constant between the TD and VR pins. 13 TD O Sets the tracking phase compensation. 14 JP I Sets the amplitude of the tracking jump signal (kick pulses).
Pin Name I/O
For the connection of the pickup photodiode. Addition to the FIN1 pin creates an RF signal and subtraction from it create an EF signal.
For the connection of the pickup photodiode. Subtraction from the F pin creates a TE signal.
For the connection of a resistor which sets the gain of the TE signal between this pin and the TE pin.
Description
15 TO O Tracking control signal output. 16 FD O Focusing control signal output. 17 FD– I Composes the focusing phase compensation constant between the FD and FA pins. 18 FA O Composes the focusing phase compensation constant between the FD- and FA- pins. 19 FA– I Composes the focusing phase compensation constant between the FA and FE pins. 20 FE O FE signal output.
21 FE– I
22 AGND O Ground of analog signals. 23 SP O Single-ended output of the signals input to the CV+ and CV- pins. 24 SPI I Spindle amp input. 25 SPG I For the connection of a resistor which sets the gain in the spindle 12cm mode. 26 SP– I For the connection of the spindle phase compensation constant with the SPD pin. 27 SPD O Spindle control signal output. 28 SLEQ I For the connection of sled phase compensation constant. 29 SLD O Sled control signal output. 30 SL– 31 SL+
For the connection of a resistor whichs sets the gain of the FE signal between this pin and the TE pin.
I Sled feed signal input from the microprocessor.
32 JP– 33 JP+ 34 TGL I Tracking gain control signal input from the DSP. Low gain when TGL is "H". 35 TOFF I Tracking off control signal input from the DSP. Off when TOFF is "H". 36 TES O Outputs the TES signal to the DSP.
I Tracking signal input from the DSP.
– 22 –
Page 23
Pin No.
37 HFL O
38 SLOF I Sled servo off control input.
I/O DescriptionPin Name
The HFL (high frequency level) signal is used to judge whether the main beam is positioned on the pit or on the mirror.
39 CV– 40 CV+ 41 RFSM O RF output. 42 RFS– O Sets the RF gain and the EFM signal's 3T compensation constant together with the RFSM pin.
43 SLC O
44 SL1 I Input to control the DSP's data slice level. 45 DGND – Ground of digital signals. 46 FSC O Output for the focus search smoothing capacitor. 47 TBC I The TBC (tracking balance control) signal sets the EF balance variation range. 48 NC – Not connected. 49 DEF O Disc defect detection output. 50 CLK I Reference clock input. 4.23 MHz is input from the DSP. 51 CL I Microprocessor command clock input. 52 DAT I Microprocessor command data input. 53 CE I Microprocessor chip enable input. 54 DRF O DRF (detect RF) is an output to detect the RF level.
55 FSS I
I CLV error signal input from the DSP.
The SLC (slice level control) signal is output to control the DSP's data slice level of the RF waveform.
The FSS (focus search select) signal switches the focus search modes (+/-search / +search with
respect to the reference voltage). 56 VCC2 – VCC of servo and digital circuits. 57 REF1 – For the connection of bypass capacitor for the reference voltage. 58 VR O Reference voltage output. 59 LF2 – Sets the time constant for disc defect detection. 60 PH1 – For the connection of a capacitor to hold the RF signal peak. 61 BH1 – For the connection of a capacitor to hold the RF signal bottom. 62 LDD O APC circuit output. 63 LDS I APC circuit input. 64 VCC1 – VCC of RF signal circuits.
– 23 –
Page 24
IC, LC865516A-5P16
Pin No. Pin Name I/O Description
1
SEG E
O
SEG E control.
10 11 12 13 14 15 16 17 18
2 3 4 5 6 7 8 9
SEG F SEG G
NC
I-RST
XT1 (IN)
NC
XT2 (OUT)
VSS
CF1 (IN)
CF2 (OUT)
VDD I-KEY0 I-KEY1
I-MOTOR
I-CD SW
O-SHIFT
NC
—
—
—
—
—
O
SEG F control.
O
SEG G control. Not connected.
I
Microprocessor reset input.
I
Connected to an external 32.768 kHz crystal oscillator. Not connected.
O
Connected to an external 32.768 kHz crystal oscillator. GND.
I
Connected to an external 5.76 MHz ceramic filter.
O
Connected to an external 5.76 MHz ceramic filter. Microprocessor power supply (+5 V).
I
Key AD input. (AD)
I
Key AD input. (AD)
I
Deck status input. (AD)
I
CD door switch status input.
O
Main clock shift output.
Not connected. 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35
O-BASS LED
O-QS LED
O-SFT LED
I-DRF
I-WRQ
NC
I-REM
O-CD ON
O-TU ON
O-P.CONT
NC
O-BEAT
O-MUTE
O-DIGIT
O-SEG REPEAT
O-COIN
I-SQOUT
—
—
—
O
BASS LED ON/OFF control output. (Not used)
O
Q sound LED ON/OFF control output.
Not used.
I
CD RF level detection input.
I
CD subcode Q standby input.
Not connected.
I
Remote control input.
O
CD power control output.
O
TU power control output.
O
The main power supply control output.
Not connected.
O
Beat sw control output.
O
Main mute output.
O
7-segment LED power supply control output.
O
REPEAT LED ON/OFF control output.
O
CD command output.
I
CD subcode Q input. 36 37 38 39 40 41
O-CQCK
O-RWC
O-DATA O-CD LED O-TU LED O-TA LED
O
CD command/CLK for subcode.
O
CD read/write control output.
O
Data output to M61509FP.
O
LED ON/OFF control output for the CD function.
O
LED ON/OFF control output for the TU function.
O
LED ON/OFF control output for the TA function. (Not used)
– 24 –
Page 25
Pin No. Pin Name I/O Description
42
NC
— Not connected. 43 44 45 46 47 48
SEG DP
SEG A
SEG B SEG C
SEG D
NC
O SEG DP control. O SEG A control. O SEG B control. O SEG C control. O SEG D control.
— Not connected.
– 25 –
Page 26
ADJUSTMENT <TUNER / DECK / CD>
< RADIO SECTION > <EZ, G>
1. LW Frequency Range Adjustment
• Test Point: TP5 (LCH), TP6 (RCH)
• Adjustment location: L016, TC005
• Method:
L016 ....................................................................... 145kHz
TC005..................................................................... 295kHz
< RADIO SECTION > <HC>
1. AM Frequency Range Adjustment
• Test Point: TP5 (LCH), TP6 (RCH)
• Adjustment location: L006, TC003
• Method:
L006 ....................................................................... 515kHz
TC003................................................................... 1635kHz
2. LW Tracking Adjustment
• Test Point: TP5 (LCH), TP6 (RCH)
• Adjustment location: L003 (1/2), TC006
• Method:
L003 (1/2)............................................................... 150kHz
TC006..................................................................... 285kHz
3. MW Frequency Range Adjustment
• Test Point: TP5 (LCH), TP6 (RCH)
• Adjustment location: L017, TC003
• Method:
L017 ....................................................................... 515kHz
TC003................................................................... 1635kHz
4. MW Tracking Adjustment
• Test Point: TP5 (LCH), TP6 (RCH)
• Adjustment location: L003 (2/2), TC004
• Method:
L003 (2/2)............................................................... 600kHz
TC004................................................................... 1400kHz
5. AM IF Adjustment
• Test Point: TP5 (LCH), TP6 (RCH)
• Adjustment location: L007
• Method:
L007 ....................................................................... 455kHz
2. AM Tracking Adjustment
• Test Point: TP5 (LCH), TP6 (RCH)
• Adjustment location: L003, TC004
• Method:
L003 ....................................................................... 600kHz
TC004................................................................... 1400kHz
3. AM IF Adjustment
• Test Point: TP5 (LCH), TP6 (RCH)
• Adjustment location: L007
• Method:
L007 ....................................................................... 455kHz
4. FM Frequency Range Adjustment
• Test Point: TP5 (LCH), TP6 (RCH)
• Adjustment location: L005, TC001
• Method:
L005 ........................................................................87MHz
TC001.................................................................... 109MHz
5. FM Tracking Adjustment
• Test Point: TP5 (LCH), TP6 (RCH)
• Adjustment location: L004, TC002
• Method:
L004 ........................................................................88MHz
TC002.................................................................... 108MHz
6. FM Frequency Range Adjustment
• Test Point: TP5 (LCH), TP6 (RCH)
• Adjustment location: L005, TC001
• Method:
L005 .....................................................................87.4MHz
TC001................................................................. 108.3MHz
7. FM Tracking Adjustment
• Test Point: TP5 (LCH), TP6 (RCH)
• Adjustment location: L004, TC002
• Method:
L004 ........................................................................88MHz
TC002.................................................................... 108MHz
8. FM IF Adjustment
• Test Point: TP5 (LCH), TP6 (RCH)
• Adjustment location: L008, L009
• Method:
L008, L009 ...........................................................10.7MHz
6. FM IF Adjustment
• Test Point: TP5 (LCH), TP6 (RCH)
• Adjustment location: L008, L009
• Method:
L008, L009 ...........................................................10.7MHz
< TAPE RECORDER SECTION >
1. Bias Adjustment
• Test tape: TTA-630
• Test Point: TP2
• Adjustment location: L801
• Method:
L801 .............................................................. 85kHz±2kHz
2. Azimuth Adjustment Settings: • Test tape: TTA-320
• Test point: PHONE JACK
• Adjustment location:Azimuth adjustment screw
Method: Play back the test tape and adjust the screw so that the
output is maximum.
– 26 –
Page 27
< CD SECTION >
1. Focus Bias Adjustment Make the focus bias adjustment when replacing and repairing the optical block.
Oscilloscope (DC range)
TP3 (RF)
TP4 (VREF)
1) Connect an oscilloscope to the test point TP3 (RF) and TP4
(VREF).
2) Turn on the power switch.
3) Insert test disc TCD-782 (YEDS-18) and play back the second
composition.
4) Adjust SFR430 so that RF signal of the test point TP3 (RF) is
MAX and CLEAREST.
EYE PATTERN
must be CLEAR and MAX
+
-
MAX
0V
VOLT / DIV: 200mV TIME / DIV: 0.5µs
– 27 –
Page 28
MECHANICAL EXPLODED VIEW 1 / 1
14
13
17
16
15
H
39
37
H
55
40
56
F
35
41
36
F
H
38
E
50
F
62
49
51
P.C.B
42
48
43
B
D
B
D
E
46
44
45
47
P.C.B
C
28
19
23
18
25
24
10
27
64
26
P.C.B
24
A
26
57
H
9
60
10
22
21
20
25
P.C.B
C
63
5
H
C
6
6
C
A
C
DA11T3C
26
A
10
D
A
D
9 8
29
C
52
30
32
7
34
33
P.C.B
D
H
D
P.C.B
58
59
31
I
CHASS,TU
54
P.C.B
P.C.B
11
63
2
1
3
12
4
7
6
C
C
C
6
5
H
D
ZZM-1
53
D
65
G
61
G
– 28 –
Page 29
MECHANICAL PARTS LIST 1 / 1
PART NO. DESCRIPTIONREF. NO. KANRI
NO.
1 8A-CDB-006-010 WINDOW,CASS 2 8A-CDB-008-010 BOX,CASS 3 8A-CDB-204-010 SPR-T,CASS 4 8A-CDB-001-010 CABI,FR 5 88-CD8-622-010 SPKR,F 77 7OHM 3W
6 8Z-CDB-208-010 HLDR,SPKR 7 8A-CDB-205-010 PLATE,OIL DUMP 8 87-063-164-010 OIL-DMPR 80 9 8A-CDB-206-010 BASE,CD 10 8A-CDB-016-010 BTN,CD
11 8A-CDB-004-010 WINDOW,DISP 12 8A-CDB-023-110 GRILLE,SPKR 13 8Z-CT6-213-010 BASE,CHUCK 14 8Z-CT6-214-010 RING,CHUCK 15 87-036-368-010 MAGNET
16 86-CT9-222-010 PLATE,MAGNET 17 86-CT9-217-010 HLDR,CHUCK A(S) 18 8A-CDB-009-210 BOX,CD 19 8A-CDB-005-010 WINDOW,CD 20 8A-CDB-213-010 BASE,FUNC
21 8A-CDB-013-010 BTN,FUNC 22 8A-CDB-014-010 BTN,QSOUND 23 8A-CDB-003-010 CHAS,CD 24 8A-CDB-021-010 LENS,FUNC 25 8A-CDB-203-010 HLDR,LED FUNC
26 88-CH6-220-010 CUSHION,CD A 27 8Z-CT9-064-010 PANEL CD 28 87-036-389-010 SW,PUSH LOCK 29 8A-CDB-218-010 SPR-T,CD 30 8A-CD9-661-010 BAR-ANT,MW/LW 3B-ACD(COI)<[S]EZ,[S]G>
30 8A-CD9-660-010 BAR-ANT,MW 2B-ACD(CO1)<[S]HC> 31 8A-CDB-210-010 DRUM,GEAR 32 87-063-165-010 OIL-DMPR 150 33 8A-CDB-214-010 BASE,VOL 34 8A-CDB-012-010 BTN,VOL
35 8A-CDB-022-010 POINTER,TU 36 8A-CDB-209-010 HLDR,BTN TUN 37 8A-CDB-211-010 GEAR,MID TUN 38 8A-CDB-011-010 BTN,TUN 39 8A-CDB-219-010 HLDR,TRAN
DESCRIPTIONREF. NO. KANRI
!
40 8A-CDB-653-010 PT,E 2.5W EI48X23<[S]EZ,[S]G>
!
40 8A-CDB-651-010 PT,H 2.5W EI48X23<[S]HC> 41 8A-CDB-019-010 HANDL,GRIP 42 8A-CDB-018-110 COVER, HANDL 43 87-A91-857-010 ANT,ROD 5SEC709
44 8A-CDB-002-010 CABI,REAR 45 8A-CDB-007-010 WINDOW,TU<[S]HC> 45 8A-CDB-027-010 WINDOW,TU EZ<[S]EZ,[S]G> 46 8A-CDB-217-010 LEVER,BAND 47 8A-CDB-020-010 LID,BATT
48 86-CT9-223-010 CUSH,FOOT 49 8A-CDB-207-010 HLDR,ANT
!
50 87-A60-178-010 JACK,AC E W/SW 51 8A-CDB-215-010 SPR-T,BATT 52 8A-CDB-220-010 HLDR,M66 BAR ANT
53 8A-CDB-131-010 KEY,REC 54 8A-CDB-216-010 PLATE,TRAN 55 8A-CDB-010-010 BTN,TU 56 87-A90-086-010 COVER, AC JACK 57 8A-CDB-618-010 FF-CABLE, 16P 1.25 FR-MAIN
58 8A-CDB-623-010 FF-CABLE, 16P 1.0 CD-RF 59 8A-CDB-619-010 FF-CABLE, 8P 1.25 CD-FR 60 8A-CDB-208-010 HLDR,LED SA/SC36 61 8A-CDB-226-010 SPR-P,REC
!
62 87-A91-369-010 SW,AC SL 2 2 2 SDKGA41700<[S]HC>
63 8A-CDB-633-010 CONN ASSY,4P SPKR 64 M8-ZZK-E90-070 DA11T3C 65 8A-CDB-225-010 PLATE,REC A 81-CD5-204-010 SCREW CD B 87-651-104-410 VT1+3-30
C 87-741-096-410 UT2+3-10 D 87-751-097-410 SCREW 3X12 E 87-261-096-410 SCREW,V+3-10 GLD F 87-741-074-410 UT2+2.6-8 G 87-745-094-410 UT2+3-6 W/O SLOT NI
H 87-751-095-410 VT2+3-8 W/O I 87-745-094-410 UT2+3-6
PART NO.
NO.
COLOR NAME TABLE
Basic color symbol Color Basic color symbol Color Basic color symbol Color
B Black C Cream D Orange G Green H Gray L Blue
LT Transparent Blue N Gold P Pink
R Red S Silver ST Titan Silver T Brown V Violet W White
WT Transparent White Y Yellow YT Transparent Yellow
LM Metallic Blue LL Light Blue GT Transparent Green LD Dark Blue DT Transparent Orange GM Metallic Green
YM Metallic Yellow DM Metallic Orange PT Transparent Pink
– 29 –
Page 30
TAPE MECHANISM EXPLODED VIEW 1 / 1
12
11
TERMINAL,LB1
A
10
9
4
3
2
1
8
14
7
55 56
6
5
13
53
B
19
17
16
21
20
22
27
24
23
15
18
28
26
25
C
54
29
31
30
48
50
51
52
49
47
46
45
44
43
42
41
36
40
37
32
39
33
34
1
35
38
ZZM-1 (File Name:EXP.EPS) 12/4/14 AR2NC
– 30 –
Page 31
TAPE MECHANISM PARTS LIST 1 / 1
PART NO. DESCRIPTIONREF. NO. KANRI
NO.
1 8Z-ZM1-254-310 SPR-C,REEL R 2 8Z-ZM1-225-110 GEAR,REEL R 3 8Z-ZM1-253-210 SPR-C,AUTO SENSOR 4 8Z-ZM1-217-110 LEVER,AUTO SENSOR 5 8Z-ZM1-212-110 LEVER,T-UP
6 8Z-ZM1-245-310 SPR-T,AUTO 7 8Z-ZM1-236-010 CLR,SLIP FF/REW 8 8Z-ZM1-252-110 SPR-C,FF/REW 9 8Z-ZM1-230-010 GEAR,SLIP FF/REW A 10 8Z-ZM1-269-010 FELT,FF/REW 2
11 8Z-ZM1-238-110 GEAR,SLIP FF/REW B 2 12 8Z-ZM1-237-110 LEVER,FF/REW 2 13 8Z-ZM1-283-010 LEVER,PAUSE 2 14 8Z-ZM1-222-010 LEVER,E-LOCK M 15 8Z-ZM1-219-010 LEVER,E-OPEN
16 8Z-ZM1-244-110 SPR-T,T-UP 17 8Z-ZM1-247-310 SPR-T,PINCH 18 8Z-ZM1-261-110 ROLLER ASSY,PINCH 19 8Z-ZM1-221-210 LEVER,PINCH 20 8Z-ZM1-205-310 LEVER,PLAY
21 8Z-ZM1-248-210 SPR-T,BRG 22 87-A91-830-010 HEAD,RP-7442 23 84-ZM2-227-310 SPR-C,AZIMUTH 24 8Z-ZM1-216-110 LEVER,AUTO 25 8Z-ZM1-246-110 SPR-T,AUTO 2
26 8Z-ZM1-233-110 GEAR,IDL REW 27 8Z-ZM1-208-010 LEVER,STOP 28 8Z-ZM1-207-010 LEVER,FF 29 8Z-ZM1-206-010 LEVER,REW 30 8Z-ZM1-211-210 LEVER,REC 2
DESCRIPTIONREF. NO. KANRI
PART NO.
NO.
31 87-A91-819-010 HEAD,EH 2NSS-2200 32 8Z-ZM1-215-010 LEVER,REC LOCK 33 87-A91-492-010 SW,LEAF MSW18560 34 8Z-ZM1-226-010 GEAR,REEL L 35 8Z-ZM1-241-210 SPR-T,PLAY
36 8Z-ZM1-220-110 LEVER,REC SENSOR 37 8Z-ZM1-249-210 SPR-T,FR 38 8Z-ZM1-242-310 SPR-T,FF/REW 39 8Z-ZM3-244-010 GEAR,CAM TD20 40 8Z-ZM1-232-010 GEAR,IDL FF/REW
41 8Z-ZM3-228-110 FLY-WHL,M3 42 8Z-ZM1-267-110 SHAFT,CAPSTAN 2 43 8Z-ZM1-228-010 GEAR,SLIP T-UP B 44 8Z-ZM1-265-010 FELT,T-UP 45 8Z-ZM1-227-010 GEAR,SLIP T-UP A
46 8Z-ZM1-251-210 SPR-C,T-UP SLIP 47 8Z-ZM1-243-310 SPR-T,STOP/PAUSE 48 87-A91-825-010 MOT,M09Y/Z 49 8Z-ZM1-271-010 PULLEY,MOT ZZM-1 50 8Z-ZM1-264-010 BELT,MAIN S
51 8Z-ZM1-260-010 SPR-P,CASETTE 52 8Z-ZM1-201-610 CHAS ASSY,ZZM-1 53 8Z-ZM1-255-310 SPR-T,E-LOCK 54 8Z-ZM1-214-210 LEVER,LOCK 55 8Z-ZM1-257-110 SPR-C,F/R
56 8Z-ZM1-275-010 W-L,1.47-4-0.25 A 84-ZM2-242-010 S-SCREW,AZ1-2-6.4 B 8Z-ZM1-270-110 V+2.6 ZZM-1 C 87-B10-301-010 W-L,1.63-3.2-0.5 SLIT
– 31 –
Page 32
CD MECHANISM EXPLODED VIEW 1 / 1
SHAFT,SLIDE
B
SF-P101NR
CHASSIS
B
1
2
A
A
3
SPINDLE MOTOR(M1)
SLED MOTOR (M2)
CD MOTOR C.B
– 32 –
Page 33
CD MECHANISM PARTS LIST 1 / 1
PART NO.
NO.
1 S2-121-A28-400 COVER GEAR 2 S2-511-A21-000 GEAR MIDDLE 3 S2-511-A21-100 GEAR,DRIVE A S1-PN2-03R-OSE SCR PAN PCS 2-3 B 87-261-073-410 SCR S-TPG FLT 2.6-6
ALL M8-ZZK-E90-070 DA11T3C
DESCRIPTIONREF. NO. KANRI
ACCESSORIES / PACKAGE LIST
PART NO.
1 8A-CDB-906-010 IB,EZ(9L)FM<EZ> 1 8A-CDB-911-010 IB,H(EC-K)FM<HC> 1 8A-CDB-904-010 IB,G(E)FM<G>
!
2 87-A80-036-010 AC CORD SET ASSY,E W/FLTR VOL<EZ> 2 87-A80-089-010 AC CORD SET,HC<HC>
!
!
2 87-A80-144-010 AC CORD SET ASSY,G BLK<G>
NO.
DESCRIPTIONREF. NO. KANRI
– 33 –
Page 34
2–11, IKENOHATA 1–CHOME, TAITO-KU, TOKYO 110, JAPAN TEL:03 (3827) 3111
Printed in Singapore9420208 0251431
Loading...
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use