How it Works
Aiwa
Loading...
CSD A100
Schematic
24 pgs3.71 Mb0
Service Manual
28 pgs3.09 Mb0
Service Manual
10 pgs2.14 Mb0
Service Manual
20 pgs792.44 Kb0
Service Manual
18 pgs687.01 Kb0
Service Manual
18 pgs640.36 Kb0
Service Manual
20 pgs756.04 Kb0

Aiwa CSD A100 Service Manual

Download
Page 1
CSD-A100
SERVICE MANUAL
COMPACT DISC RADIO
CASSETTE RECORDER
BASIC TAPE MECHANISM : ZZM-1 YR2NF BASIC CD MECHANISM : DA11T3C
S/M Code No. 09-00C-342-2N7
DATA
Page 2
SPECIFICATIONS
Design and specifications are subject to change
•
without notice
.
-2-
Page 3
PROTECTION OF EYES FROM LASER BEAM DURING SERVICING
This set employs laser. Therefore, be sure to follow carefully the instructions below when servicing.
WARNING!
WHEN SERVICING, DO NOT APPROACH THE LASER EXIT WITH THE EYE TOO CLOSELY. IN CASE IT IS NECESSARY TO CONFIRM LASER BEAM EMISSION. BE SURE TO OBSERVE FROM A DISTANCE OF MORE THAN 30cm FROM THE SURFACE OF THE OBJECTIVE LENS ON THE OPTICAL PICK-UP BLOCK.
Caution: Invisible laser radiation when open and interlocks defeated avoid expo­sure to beam. Advarsel:Usynling laserståling ved åbning, når sikkerhedsafbrydere er ude af funktion. Undgå udsættelse for stråling.
VAROITUS!
Laiteen Käyttäminen muulla kuin tässä käyttöohjeessa mainit­ulla tavalla saattaa altistaa käyt-täjän turvallisuusluokan 1 ylit­tävälle näkymättömälle lasersäteilylle.
VARNING!
Om apparaten används på annat sätt än vad som specificeras i denna bruksanvising, kan användaren utsättas för osynling laserstrålning, som överskrider gränsen för laserklass 1.
CAUTION
Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.
ATTENTION
L'utilisation de commandes, réglages ou procédures autres que ceux spécifiés peut entraîner une dangereuse exposition aux radiations.
ADVARSEL!
Usynlig laserståling ved åbning, når sikkerhedsafbrydereer ude af funktion. Undgå udsættelse for stråling.
This Compact Disc player is classified as a CLASS 1 LASER product. The CLASS 1 LASER PRODUCT label is located on the rear exterior.
CLASS 1 KLASSE 1 LUOKAN 1 KLASS 1
LASER PRODUCT LASER PRODUKT LASER LAITE LASER APPARAT
-3-
Page 4
Precaution to replace Optical block (SF-P101NR)
Body or clothes electrostatic potential could ruin laser diode in the optical block. Be sure ground body and workbench, and use care the clothes do not touch the diode.
1) After the connection, remove solder shown in the right figure.
PICK UP ASSY
SF-P101NR
Solder
1
16
TO/FROM CD C.B
-4-
Page 5
ELECTRICAL MAIN PARTS LIST-1/4
REF. NO PART NO. KANRI DESCRIPTION
NO.
IC
87-A20-955-010 IC,LA1828 87-A21-064-010 IC,LA4227 87-A21-443-040 C-IC,M62495AFP 87-A20-446-010 C-IC,LA9241ML 87-A20-459-010 C-IC,LC78622ED
87-A20-856-010 IC,BA6898S 8A-CD9-610-010 C-IC,LC865516A-5P16 87-A21-607-010 IC,NJM14558LD
TRANSISTOR
89-327-143-080 TR,2SC2714 (0.1W) 87-026-447-080 TR,2SC1740S R 87-026-463-080 TR,2SA933S (0.3W) 87-A30-288-040 C-TR,DTC114YKA 89-318-154-080 TR,2SC1815 (0.4W)
89-112-965-080 TR,2SA1296 (0.75W) 87-026-291-080 TR,DTC124XS 89-213-702-010 TR,2SB1370 (1.8W) 87-026-462-080 TR,2SC1740 S(RS 0.3W) 89-109-332-380 TR,2SA933RS
87-A30-515-080 TR,2SA1979 O/Y 87-A30-436-040 C-TR,DTC144TKA 89-317-403-080 TR,2SC1740S 87-A30-287-040 C-TR,DTC114TKA 87-026-464-080 TR,DTC114TS (0.3W)
DIODE
87-020-465-080 DIODE,1SS133 (110MA) 87-A40-916-040 C-VARI-CAP,HVC202A 87-A40-650-080 ZENER,MTZJ6.8A 87-070-345-080 DIODE,IN4148 87-A40-648-080 ZENER,MTZJ8.2A
87-A40-234-080 ZENER,MTZJ5.6A 87-017-978-080 DIODE,1N4003 87-017-932-080 ZENER,MTJ6.2B 87-A40-465-010 DIODE,FR202
MAIN C.B
C211 87-A11-177-080 C-CAP,S 0.15-16 K B C212 87-A11-177-080 C-CAP,S 0.15-16 K B C215 87-016-460-080 C-CAP,S 0.22-16 B C216 87-016-460-080 C-CAP,S 0.22-16 B C231 87-010-213-080 C-CAP,S 0.015-50 B
C232 87-010-213-080 C-CAP,S 0.015-50 B C233 87-A10-201-080 C-CAP,S0.33-16 KB C234 87-A10-201-080 C-CAP,S0.33-16 KB C235 87-016-669-080 C-CAP,S 0.1-25 K B C236 87-016-669-080 C-CAP,S 0.1-25 K B
C237 87-010-371-080 CAP, ELECT 470-6.3V C239 87-010-197-080 CAP, CHIP 0.01 DM C240 87-010-197-080 CAP, CHIP 0.01 DM C247 87-010-401-080 CAP, ELECT 1-50V C248 87-010-401-080 CAP, ELECT 1-50V
C310 87-010-248-080 CAP, ELECT 220-10V C316 87-010-263-080 CAP, ELECT 100-10V C317 87-015-819-080 CAPACITOR,0.01 C801 87-010-248-080 CAP, ELECT 220-10V C805 87-012-365-080 C-CAP,S 0.027-25VBK
C806 87-012-365-080 C-CAP,S 0.027-25VBK C807 87-010-405-080 CAP, ELECT 10-50V C808 87-010-405-080 CAP, ELECT 10-50V C809 87-010-401-080 CAP, ELECT 1-50V C810 87-010-401-080 CAP, ELECT 1-50V
C811 87-010-178-080 CHIP CAP 1000P C812 87-010-178-080 CHIP CAP 1000P C816 87-010-180-080 C-CER 1500P
REF. NO PART NO. KANRI DESCRIPTION
C817 87-010-180-080 C-CER 1500P C821 87-010-401-080 CAP, ELECT 1-50V C822 87-010-401-080 CAP, ELECT 1-50V C829 87-010-178-080 CHIP CAP 1000P C830 87-010-178-080 CHIP CAP 1000P
C833 87-018-195-080 CAP, CER 1200P-16V C834 87-010-248-080 CAP, ELECT 220-10V C843 87-010-197-080 CAP, CHIP 0.01 DM C844 87-018-124-080 CAP, CER 270P-50V C845 87-010-178-080 CHIP CAP 1000P
C846 87-010-263-080 CAP, ELECT 100-10V C851 87-010-186-080 CAP,CHIP 4700P C852 87-010-178-080 CHIP CAP 1000P C853 87-A11-132-080 CAP,TC U 0.01-50 K B CN201 87-099-018-010 CONN,16P
CN801 87-A60-110-010 CONN,4P V S2M-4W CNA302 8A-CDA-629-010 CONN ASSY,6P MA-TU L801 87-007-342-010 COIL,OSC 85K BIAS SW801 8Z-CD9-609-010 SW,SL 1-6-2 PS62D01
CD C.B
C30 87-010-260-080 CAP, ELECT 47-25V C251 87-010-404-080 CAP, ELECT 4.7-50V C263 87-010-178-080 CHIP CAP 1000P C264 87-010-178-080 CHIP CAP 1000P C265 87-010-263-080 CAP, ELECT 100-10V
C266 87-010-263-080 CAP, ELECT 100-10V C267 87-010-112-080 CAP, ELECT 100-16V C268 87-010-112-080 CAP, ELECT 100-16V C271 87-010-237-080 CAP, ELECT 1000-16V C272 87-010-237-080 CAP, ELECT 1000-16V
C278 87-010-405-080 CAP, ELECT 10-50V C279 87-010-385-080 CAP, ELECT 220-25V
!
C301 87-016-495-000 CAP,E 3300-25 M SMG C306 87-010-404-080 CAP, ELECT 4.7-50V C307 87-010-401-080 CAP, ELECT 1-50V
C308 87-010-221-080 CAP, ELECT 470-10V C311 87-010-374-080 CAP, ELECT 47-10V C312 87-010-385-080 CAP, ELECT 220-25V C321 87-010-197-080 CAP, CHIP 0.01 DM C322 87-010-263-080 CAP, ELECT 100-10V
C325 87-010-405-080 CAP, ELECT 10-50V C401 87-010-403-080 CAP, ELECT 3.3-50V C402 87-010-197-080 CAP, CHIP 0.01 DM C403 87-010-263-080 CAP, ELECT 100-10V C404 87-010-248-080 CAP, ELECT 220-10V
C405 87-010-197-080 CAP, CHIP 0.01 DM C406 87-010-374-080 CAP, ELECT 47-10V C407 87-010-178-080 CHIP CAP 1000P C408 87-010-198-080 CAP, CHIP 0.022 C409 87-010-248-080 CAP, ELECT 220-10V
C410 87-010-263-080 CAP, ELECT 100-10V C411 87-A11-177-080 C-CAP,S 0.15-16 K B C412 87-010-401-080 CAP, ELECT 1-50V C413 87-016-369-080 C-CAP,S 0.033-25 B K C414 87-010-405-080 CAP, ELECT 10-50V
C416 87-010-545-080 CAP, ELECT 0.22-50V C417 87-012-157-080 C-CAP,S 330P-50 CH C418 87-010-213-080 C-CAP,S 0.015-50 B C419 87-A11-608-080 C-CAP,S 0.33-25 K B C420 87-016-369-080 C-CAP,S 0.033-25 B K
C421 87-A11-177-080 C-CAP,S 0.15-16 K B C422 87-010-184-080 CHIP CAPACITOR 3300P(K) C423 87-010-992-080 C-CAP,S 0.047-25 B C425 87-010-176-080 C-CAP,S 680P-50 SL C426 87-A11-608-080 C-CAP,S 0.33-25 K B
C428 87-010-197-080 CAP, CHIP 0.01 DM C429 87-010-186-080 CAP,CHIP 4700P C430 87-012-156-080 C-CAP,S 220P-50 CH
NO.
-5-
Page 6
ELECTRICAL MAIN PARTS LIST-2/4
REF. NO PART NO. KANRI DESCRIPTION
NO.
C431 87-010-545-080 CAP, ELECT 0.22-50V C432 87-010-374-080 CAP, ELECT 47-10V C433 87-010-401-080 CAP, ELECT 1-50V C434 87-010-184-080 CHIP CAPACITOR 3300P(K) C435 87-010-197-080 CAP, CHIP 0.01 DM
C436 87-010-374-080 CAP, ELECT 47-10V C437 87-010-404-080 CAP, ELECT 4.7-50V C438 87-016-669-080 C-CAP,S 0.1-25 K B C439 87-010-178-080 CHIP CAP 1000P C440 87-010-145-080 C-CAP,S 1P-50 CH
C441 87-010-197-080 CAP, CHIP 0.01 DM C442 87-010-313-080 CAP, CHIP 18P C445 87-012-368-080 C-CAP,S 0.1-50 F C446 87-012-368-080 C-CAP,S 0.1-50 F C447 87-012-368-080 C-CAP,S 0.1-50 F
C448 87-010-315-080 C-CAP,S 27P-50 CH C450 87-012-140-080 CAP 470P C451 87-012-156-080 C-CAP,S 220P-50 CH C455 87-010-247-080 CAP, ELECT 100-50V C457 87-010-312-080 C-CAP,S 15P-50 CH
C458 87-010-312-080 C-CAP,S 15P-50 CH C459 87-010-263-080 CAP, ELECT 100-10V C460 87-015-819-080 CAPACITOR,0.01 C461 87-010-197-080 CAP, CHIP 0.01 DM C462 87-010-248-080 CAP, ELECT 220-10V
C463 87-010-197-080 CAP, CHIP 0.01 DM C465 87-010-404-080 CAP, ELECT 4.7-50V C466 87-012-368-080 C-CAP,S 0.1-50 F C467 87-010-263-080 CAP, ELECT 100-10V C469 87-012-154-080 C-CAP,S 150P-50 CH
C471 87-015-785-080 CHIP CAPACITOR, 0.1FZ-25Z C472 87-015-785-080 CHIP CAPACITOR, 0.1FZ-25Z C473 87-015-785-080 CHIP CAPACITOR, 0.1FZ-25Z C474 87-015-785-080 CHIP CAPACITOR, 0.1FZ-25Z C475 87-010-197-080 CAP, CHIP 0.01 DM
C476 87-010-236-080 CAP,E 1000-10 SME C477 87-010-197-080 CAP, CHIP 0.01 DM C478 87-010-263-080 CAP, ELECT 100-10V C479 87-010-197-080 CAP, CHIP 0.01 DM C480 87-010-221-080 CAP, ELECT 470-10V
C481 87-010-405-080 CAP, ELECT 10-50V C482 87-010-405-080 CAP, ELECT 10-50V C489 87-012-368-080 C-CAP,S 0.1-50 F C490 87-012-368-080 C-CAP,S 0.1-50 F C491 87-010-197-080 CAP, CHIP 0.01 DM
C492 87-010-221-080 CAP, ELECT 470-10V C494 87-010-197-080 CAP, CHIP 0.01 DM C501 87-012-368-080 C-CAP,S 0.1-50 F C502 87-010-322-080 C-CAP,S 100P-50 CH C503 87-010-322-080 C-CAP,S 100P-50 CH
C504 87-010-322-080 C-CAP,S 100P-50 CH C505 87-010-322-080 C-CAP,S 100P-50 CH C506 87-010-322-080 C-CAP,S 100P-50 CH C510 87-016-669-080 C-CAP,S 0.1-25 K B C831 87-010-198-080 CAP, CHIP 0.022
CN202 8A-CH4-689-010 CONN,3P V 2.5 CN205 87-A60-109-010 CONN,2P V S2M-2W CN301 8A-CH4-689-010 CONN,3P V 2.5 CN401 87-A60-424-010 CONN,16P V TOC-B CN403 87-099-201-010 CONN,8P 6216 H
CN802 8A-CH4-687-010 CONN,4P V 2.5 CNA402 8A-CDA-625-010 CONN ASSY,6P CD-ME L401 87-003-102-080 COIL, 10UH L404 87-003-152-080 COIL, 100UH R840 87-029-124-010 RES,FUSE 2.2-1/4
SFR430 87-024-437-080 SFR100K,RH063EC X401 8Z-CD5-633-010 VIB, CER16.93MHZ FCR16.93M2
FRONT C.B
REF. NO PART NO. KANRI DESCRIPTION
NO.
C601 87-010-313-080 CAP, CHIP 18P C602 87-010-315-080 C-CAP,S 27P-50 CH C603 87-010-319-080 C-CAP,S 56P-50 CH C604 87-010-317-010 CHIP CAP,S 39P CH C605 87-010-264-040 CAP,E 100-10 5L
C606 87-012-368-080 C-CAP,S 0.1-50 F C607 87-015-779-010 CHIP CAPACITOR, 0.01 C608 87-010-415-080 CAP ELE SRE 10-50V C609 87-010-493-080 CAP,E 0.47-50 GAS C611 87-A10-189-040 CAP,E 220-10
C613 87-012-368-080 C-CAP,S 0.1-50 F C614 87-010-312-080 C-CAP,S 15P-50 CH C627 87-015-779-010 CHIP CAPACITOR, 0.01 C628 87-015-779-010 CHIP CAPACITOR, 0.01 C629 87-015-779-010 CHIP CAPACITOR, 0.01
C630 87-010-264-040 CAP,E 100-10 5L C631 87-015-779-010 CHIP CAPACITOR, 0.01 CN601 87-099-757-010 CONN,16P 9604S F CN602 87-A60-079-010 CONN,08P H 9604S-08F CNA604 8A-CDA-623-010 CONN ASSY,7P KEY
JW603 87-008-372-080 FILTER, EMI BL OIRNI JW605 87-003-097-080 COIL,1UH JW606 87-003-097-080 COIL,1UH JW608 87-003-097-080 COIL,1UH JW627 87-008-372-080 FILTER, EMI BL OIRNI
JW633 87-003-098-080 COIL,2.2UH L601 87-003-098-080 COIL,2.2UH LED611 87-CD8-616-010 LED,SA36-11 HWA-11.0 S601 87-A91-704-080 SW,TACT EVQ 214 05R S602 87-A91-704-080 SW,TACT EVQ 214 05R
S603 87-A91-704-080 SW,TACT EVQ 214 05R S604 87-A91-704-080 SW,TACT EVQ 214 05R S605 87-A91-704-080 SW,TACT EVQ 214 05R S611 87-A91-704-080 SW,TACT EVQ 214 05R X601 87-030-273-010 VIB,XTAL 32.768K5PPM
X602 87-030-376-080 VIB,CER CSA5.76MG200
TUNER C.B
C1 87-010-314-080 C-CAP,S 22P-50V C2 87-010-316-080 C-CAP,S 33P-50 CH C3 87-010-314-080 C-CAP,S 22P-50V C4 87-010-148-080 CAP, CHIP S 75P SL C5 87-010-378-080 CAP, ELECT 10-16V
C7 87-012-156-080 C-CAP,S 220P-50 CH C8 87-010-197-080 CAP, CHIP 0.01 DM C9 87-010-311-080 CAP 12P C10 87-010-197-080 CAP, CHIP 0.01 DM C11 87-010-331-080 C-CAP,S 8P-50 UJ
C12 87-010-314-080 C-CAP,S 22P-50V C13 87-010-322-080 C-CAP,S 100P-50 CH C14 87-010-327-080 C-CAP,S 4P-50 UJ C15 87-016-669-080 C-CAP,S 0.1-25 K B C16 87-010-178-080 CHIP CAP 1000P
C17 87-016-669-080 C-CAP,S 0.1-25 K B C18 87-010-198-080 CAP, CHIP 0.022 C19 87-016-669-080 C-CAP,S 0.1-25 K B C20 87-010-400-080 CAP, ELECT 0.47-50V C21 87-010-403-080 CAP, ELECT 3.3-50V
C22 87-010-197-080 CAP, CHIP 0.01 DM C26 87-012-358-080 C-CAP,S 0.47-10 F Z C27 87-012-358-080 C-CAP,S 0.47-10 F Z C28 87-010-992-080 C-CAP,S 0.047-25 B C29 87-010-992-080 C-CAP,S 0.047-25 B
C30 87-010-248-080 CAP, ELECT 220-10V C31 87-010-379-080 CAP, ELECT 22-16V C32 87-010-197-080 CAP, CHIP 0.01 DM C33 87-010-197-080 CAP, CHIP 0.01 DM C34 87-010-197-080 CAP, CHIP 0.01 DM
-6-
Page 7
ELECTRICAL MAIN PARTS LIST-3/4
REF. NO PART NO. KANRI DESCRIPTION
NO.
C35 87-010-197-080 CAP, CHIP 0.01 DM C36 87-010-263-080 CAP, ELECT 100-10V C37 87-010-197-080 CAP, CHIP 0.01 DM C38 87-010-197-080 CAP, CHIP 0.01 DM C51 87-010-197-080 CAP, CHIP 0.01 DM
C56 87-010-152-080 C-CAP,S 8P-50 CH CF1 87-A90-128-010 FLTR,AM IF CFAL-455 CF2 87-008-261-010 FILTER, SFE10.7MA5-A CF3 87-008-261-010 FILTER, SFE10.7MA5-A CN2 87-A60-116-010 CONN,6P H S2M-6WR
L2 87-A50-560-010 COIL,FM BPF(ACD) L3 8A-CD9-660-010 BAR-ANT,MW 2B-ACD(COI) L4 87-A50-562-010 COIL,FM RF EX(ACD) L5 87-A50-564-010 COIL,FM OSC EX(ACD) L6 87-A50-337-010 COIL,AM OSC
L7 87-A50-579-010 COIL,AM IFT(ACD) L8 87-A50-335-010 COIL,FM IFT (TOKO) L9 87-A50-577-010 COIL,FM DET(ACD) L10 87-005-849-080 COIL,10UH(CECS) PVC1 87-A91-170-010 TUN-CAP,20P-335P FA-2217 N000-
SW1 87-A91-548-010 SW,SL-2-3 SK23E01G06
HP C.B
CN204 87-A60-685-010 CONN,4P H WHT EH CN605 87-A60-117-010 CONN,7P H S2M-7WR CNA203 8A-CDA-628-110 CONN ASSY,4P MA-HP J251 87-A60-569-010 JACK,HTJ-035-18
REF. NO PART NO. KANRI DESCRIPTION
BATT1 C.B
C901 87-010-192-080 C-CAP,S 0.022-50 F C902 87-010-192-080 C-CAP,S 0.022-50 F C903 87-010-192-080 C-CAP,S 0.022-50 F C904 87-010-192-080 C-CAP,S 0.022-50 F CNA901 8A-CDA-627-010 CONN ASSY,3P PWR
!
PR901 87-A90-092-080 PROTECTOR,2.5A 491 SP901 87-CD6-213-010 SPR-C,BATT (-) SP902 87-CD6-213-010 SPR-C,BATT (-)
BATT2 C.B
SP903 87-CD6-213-010 SPR-C,BATT (-) SP904 87-CD6-213-010 SPR-C,BATT (-)
MOTOR C.B
M2 90-262-576-910 MOTOR GEAR ASSY PIN3 91-564-722-110 CONNECTOR 6P SW1 91-572-085-120 LEAF SW
VOL SEL C.B
!
F901 87-035-347-010 FUSE, 2.5A 250V T FC901 87-033-213-010 CLAMP, FUSE SMK FC902 87-033-213-010 CLAMP, FUSE SMK
NO.
-7-
Page 8
ELECTRICAL MAIN PARTS LIST-4/4
• Regarding connectors, they are not stocked as they are not the initial order items. The connectors are available after they are supplied from connector manufacturers upon the order is received.
CHIP RESISTOR PART CODE
Chip Resistor Part Coding
88
A
Resistor Code
Chip resistor
Wattage Type Tolerance 1/16W 1005 5% CJ
1/16W 1/10W
1/8W
1608 2125
3216
5% 5%
5%
Symbol
CJ CJ
CJ
Figure
Value of resistor
Form
L
Dimensions (mm)
t
W
0.55
Resistor Code
108 118
128
LW t
1.0 0.5 0.35 104
1.6 0.8 0.45 2 1.25 0.45
3.2
1.6
: A : A
-8-
Page 9
IC BLOCK DIAGRAM-1/2 IC, BA6898S
IC, LA1828 IC, NJM14558L
A OUTPUT
A– INPUT
A+ INPUT
–
V
B+ INPUT
B– INPUT
A
B
B OUTPUT
-9-
V
+
Page 10
IC BLOCK DIAGRAM-2/2 IC, M62495AFP
AUTO RESET
-10-
Page 11
WIRING-1/4 (MAIN/CD)
101112131415161718192021222324
1234567892526272829303132
A
B
C
D
E
F
G
H
JW101
JR101
C317
C418
R820
I
J
K
L
M
N
O
P
Q
-11-
R819
R
S
T
U
Page 12
SCHEMATIC DIAGRAM-1/4 (MAIN)
M62495AFP
68k
1.2k
0.01
1.2K
0.01
R236
3.9k
LED606
6224-10ID RED
270
270
R217 JR
LED607
6224-10ID RED
JW129 JW
IC801 NJM14558LD
D810
1SS133
D809
1SS133
R808 220
1/4W
JR101
22k
JW101
22k
R820 8.2k
R819 8.2k
R822
22k
R821
22k
2.2k
R218 JR
MTZJ6.8A
100
C280
JR
C281
JR
1/4W
JR
R269
R311
1N4148100
JR
1/4W
MTJ6.2B
J901
(TO DECK CHASSIS)
1/4W
R838 JR
-12-
DRY BATTERY
R14X8
DC 12V
Page 13
SCHEMATIC DIAGRAM-2/4 (CD)
A
A
A
A
PIN3
JR
2SA1979
-13-
Page 14
WIRING-2/4 (MOTOR)
123456789101112131415
A
B
C
H MOTOR C.B
M2
_
(SLED MOTOR)
+
(INSIDE LIMIT SW)
6
SW1
PIN3
M2
SW1
M3
(SPINDLE MOTOR)
D
E
F
G
H
I
J
K
L
1
TO B CD C.B CNA402
M3
_
+
M
N
O
P
Q
R
S
T
U
-14-
Page 15
WIRING-3/4 (FRONT/HP/BATT1/BATT2)
101112131415161718192021222324
1234567892526272829303132
A
B
C
D
E
F
G
H
C631
C630
J901
C629
C628
C627
I
J
K
L
M
N
O
P
Q
R
-15-
JW604
S
T
U
Page 16
SCHEMATIC DIAGRAM-3/4 (FRONT)
CN602
JW604
CONN, 8P H 9604S-08F
D-SW
4.7k
JR JR JR
JR605 4.7k JR604 4.7k
JW615 1k
JW614 1k
6224
JW613 1k
C627 0.01
JW608
1 H
JW633 2.2 H
JW627 FB
JR
C628
0.01
C629
0.01
FB
JW603
+
C630
100 10V
JW605 1 H
JW606 1 H
A
6224
A
C631 0.01
-16-
DTC114TK
Page 17
WIRING-4/4 (TUNER)
123456789101112131415
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
-17-
R
S
T
U
Page 18
L005, TC001
FM FREQ. RANGE
ADJ.
FM RF
JW
FM OSC
FM BPF
10
C
C038
0.01
A
75p
8p
SCHEMATIC DIAGRAM-4/4 (TUNER)
-18-
Page 19
TRANSISTOR ILLUSTRATION
ECB
2SA933S 2SC1815 2SC1740 2SA1979
C
B
E
2SC2714 DTC114TK DTC114YK DTC144TK
ECB
DTC114TS
BCE
2SB1370
ECB ECB
2SA1296
2SC1740S DTC124XS
-19-
Page 20
ELECTRICAL ADJUSTMENT-1/2
D
TUNER C.B
1
L003
(BAR ANT)
2
2
5
B
CD C.B
IC404
PVC001
TC4 TC3
L004
L008
L006
L005
TC1TC2
IC001
L007
L009
19
63 74
89
SFR430
CN401
A
MAIN C.B
E
H.P. C.B
J251 PHONES
!
CN201
M1 (TAPE MOTOR)
IC801
1
CN801
L801
0
RPH
-20-
8
9
Page 21
ELECTRICAL ADJUSTMENT-2/2
< TUNER SECTION >
1. AM Freq. Range Adjustment
L006 ............................................................................. 517kHz
TC003......................................................................... 1750kHz
2. AM Tracking Adjustment
L003 ............................................................................. 600kHz
TC004......................................................................... 1400kHz
3. AM IF Adjustment Settings: • Test point: IC001 (LA1828) 19PIN
• Adjustment location: L007
Method: Adjust L007 so that the output level at 1400kHz
becomes maximum.
4. FM Freq. Range Adjustment
L005 ........................................................................... 87.0MHz
TC001....................................................................... 109.0MHz
5. FM Tracking Adjustment
L004 ........................................................................... 88.0MHz
TC002....................................................................... 108.0MHz
6. FM IF Adjustment Settings: • Test point: IC001 (LA1828) 19PIN
• Adjustment location: L008
Method: Adjust L008 so that the output level at 98.0MHz
becomes balanced.
< DECK SECTION >
8. Tape Speed Adjustment Settings : • Test tape : TTA–100
• Test point : J251 (PHONES jack)
• Adjustment location : SFR of deck motor
Method : Play back the test tape and adjust SFR so that the
frequency counter reads 3000Hz ± 30Hz.
9. Head Azimuth Adjustment Settings : • Test tape : TTA–320
• Test point : J251 (PHONES jack)
• Adjustment location : Azimuth adjustment screw
Method : Play back the 8kHz signal of the test tape and adjust
screw so that the output becomes maximum.
10. Bias frequncy Adjustment
L801..................................................................85kHz±0.5kHz
< CD SECTION >
11. FE Balance Adjustment Settings : • Test point : IC401 PIN58 (VR), IC401 PIN 20
(FE)
• Adjustment location : SFR430
Method : Playback the disc and adjust SFR430 so that the test
point voltage becomes 0V.
7. FM Balance Adjustment Settings: • Test point: IC001 (LA1828) 19PIN
• Adjustment location: L009
Method: Adjust L009 so that the output level at 98.0MHz
becomes balanced.
-21-
Page 22
IC DESCRIPTION-1/3 (LA9241ML)-1/2
Pin No. Pin Name I/O Description
1
FIN2
Pin to which external pickup photo diode is connected. RF signal is created by adding with the
I
FIN1 pin signal. FE signal is created by subtracting from the FIN1 pin signal.
10 11
12
13 14 15 16
2
3
4 5 6 7
8
9
FIN1
E
F
TB
TE-
TE
TESI
SCI
TH TA
TD-
TD
JP TO FD
Pin to which external pickup photo diode is connected.
I
Pin to which external pickup photo diode is connected. TE signal is created by subtracting from
I
the F pin signal. Pin to which external pickup photo diode is connected.
I
DC component of the TE signal is input. (Pull up)
I
Pin to which external resistor setting the TE signal gain is connected between the TE pin.
I
TE signal output pin.
O
TES “Track Error Sense” comparator input pin. TE signal is passed through a band-pass filter
I
then input. (Pull up) Shock detection signal input pin. (Pull up)
I
Tracking gain time constant setting pin. (Pull up)
I
TA amplifier output pin. (Pull up)
O
Pin to which external tracking phase compensation constants are connected between the TD and
I
VR pins. Tracking phase compensation setting pin.
I
Tracking jump signal (kick pulse) amplitude setting pin. (Pull up)
I
Tracking control signal output pin.
O
Focusing control signal output pin.
O
17
18
19
20 21 22 23 24 25
26
27 28 29
30, 31
FD-
FA
FA-
FE
FE-
AGND
SP
SPI
SPG
SP-
SPD
SLEQ
SLD
SL-, SL+
—
Pin to which external focusing phase compensation constants are connected between the FD and
I
FA pins. Pin to which external focusing phase compensation constants are connected between the FD–
I
and FA– pins. Pin to which external focusing phase compensation constants are connected between the FA and
I
FE pins. FE signal output pin.
O
Pin to which external FE signal gain setting resistor is connected between the FE pin.
I
Analog signal GND. Signal ended output of the CV+and CV- pin input signal.
O
Spndle amp input.
I
Pin to which external spindle gain setting resistor in 12 cm mode is connected. (Not connected)
I
Pin to which external spindle phase compensation constants are connected together with SPD
I
pin. Spindle control signal output pin.
O
Pin to which external sled phase compensation constants are connected.
I
Sled control signal output pin.
O
Sled advance signal input pin from microprocessor. (Pin 31: Not connected)
I
32, 33
34 35
JP-, JP+
TGL
TOFF
Tracking jump signal input pin from DSP.
I
Tracking gain control signal input from DSP. Low gain when TGL = H.
I
Tracking off control signal input pin from DSP. Off when TOFF = H.
I
-22-
Page 23
IC DESCRIPTION-1/3 (LA9241ML)-2/2
Pin No. Pin Name I/O Description
O
36
37
38
39, 40
41
42
43 44
TES
HFL
SLOF
CV–, CV+
RFSM
RFS-
SLC
SLI
Pin from which TES signal is output to DSP. “High Frequency Level” is used to judge whether the main beam position is on top of bit or on
O
top of mirror.
I
Sled servo off control input pin.
I
CLV error signal input pin from DSP.
O
RF output pin. RF gain setting and EFM signal 3T compensation constant setting pin together with RFSM pin.
I
(Pull up)
O
“Slice Level Control” is the output pin which controls the RF signal data slice level by DSP.
I
Input pin which control the data slice level by the DSP. 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61
DGND
FSC
TBC
NC DEF CLK
CL
DAT
CE
DRF
FSS
VCC2
REFI
VR
LF2 PHI
BHI
—
O
—
O
O
— —
O
Digital system GND. Output pin to which external focus search smoothing capacitor is connected. (Pull up)
I
“Tracking Balance Control” EF balance variable range setting pin. (Pull up) No connection. Disc defect detector output pin.
I
Reference clock input pin. 4.23 MHz of the DSP is input.
I
Microprocessor command clock input pin.
I
Microprocessor command data input pin.
I
Microprocessor command chip enable input pin. “Detect RF” RF level detector output.
I
“Focus Search Select” focus search mode (± search/+ search) select pin. (Not connected) Servo system and digital system Vcc pin. Pin to which external bypass capacitor for reference voltage is connected. (Pull down) Reference voltage output pin.
I
Disc defect detector time constant setting pin. (Pull down)
I
Pin to which external capacitor for RF signal peak holding is connected. (Pull up)
I
Pin to which external capacitor for RF signal bottom holding is connected. (Pull down) 62 63 64
LDD LDS
VCC1
—
O
APC circuit output pin.
I
APC circuit input pin.
RF system Vcc pin.
-23-
Page 24
IC DESCRIPTION-2/3 (LC78622ED)-1/2
Pin No. Pin Name I/O Description
1
DEFI
I
Defect sense signal (DEF) input pin. (Connect to 0V when not used).
2 3 4 5 6 7 8
9 10 11
12, 13
14
15 16 17 18
TAI
PDO
VVSS
ISET
VVDD
FR
VSS
EFMO
EFMIN
T2
CLV+, CLV-
___
V/P
HFL TES
TOFF
TGL
—
—
—
I
O
For PLL.
I
I
Digital system GND. Be sure to connect to 0V.
O
For slice level control.
I I
Test signal input pin with built-in pull-down resistor. Be sure to connect to 0V.
O
Disc motor control output. Three level output is possible using command. Rough servo or phase control automatic selection monitoring output pin. Rough servo at H.
O
Phase servo at L.
I
Track detect signal input pin. Schmidt input.
I
Tracking error signal input pin. Schmidt input.
O
Tracking OFF output pin.
O
Tracking gain selection output pin. Gain boost at L.
Test signal input pin with built-in pull-down resistor. Be sure to connect to 0V. Phase comparator output pin to control external VCO. GND pin for built-in VCO. Be sure to connect to 0V. Pin to which external resistor adjusting the PD0 output current. Power supply pin for built-in VCO. Pin for VCO frequency range adjustment.
EFM signal output pin. EFM signal input pin.
19, 20
21
22
23 24 25 26 27 28 29 30 31
32, 33
34 35 36 37
JP+, JP-
PCK
FSEQ
VDD
SL+
SL-
CONT3
PUIN
RW
EMPH
C2F DOUT T3, T4
N.C.
MUTEL
LVDD LCHO
—
—
—
—
O
Track jump control signal output pin. Three level output is possible using command.
O
EFM data playback clock monitoring pin 4.3218 MHz when phase is locked in. (Not connected) Sync signal detection output pin. H when the sync signal which is detected from EFM signal and
O
thesync signal which is internally generated agree. (Not connected) Digital system power supply pin.
O
Moves the sled to outer circumference. (Not connected)
O
Moves the sled to inner circumference. (Not connected) Not connected.
I
CD pickup inner switch detection.
O
Read, wright signal.
O
De-emphasis monitor output pin. De-emphasis disc is being played back at H. (Not connected)
O
C2 flag output pin. (Not connected)
O
DIGITAL OUT output pin. (EIAJ format). (Not connected)
I
Test signal input pin with built-in pull-down resistor. Be sure to connect to 0V. Not used. Set the pin to open.
O
L-channel 1-bit DAC.
O
L-channel mute output pin. (Not connected) L-channel power supply pin.
L-channel output pin. 38 39 40 41 42
LVSS RVSS
RCHO
RVDD
MUTER
— —
—
O
R-channel 1-bit DAC.
O
L-channel GND. Be sure to connect to 0V.
R-channel GND. Be sure to connect to 0V.
R-channel output pin.
R-channel power supply pin.
R-channel mute output pin. (Not connected)
-24-
Page 25
IC DESCRIPTION-2/3 (LC78622ED)-2/2
Pin No. Pin Name I/O Description
43
XVDD
—
Crystal oscillator power supply pin. 44 45 46 47 48 49
50
51
52
53 54 55 56 57 58 59
XOUT
XIN XVSS SBSY EFLG
PW
SFSY
SBCK
FSX
WRQ RWC
SQOUT
COIN
___________
CQCK
RES
T11
—
O
Pin to which external 16.9344 MHz crystal oscillator is connected.
I
Crystal oscillator GND pin. Be sure to connect to 0V. Subcode block sync signal output pin. (Not connected)
O
C1, C2, single and dual correction monitoring pin. (Not connected)
O
Subcode P, Q, R, S, T, U and W output pin. (Not connected)
O
Subcode frame sync signal output pin. Falls down when subcode enters standby.
O
(Not connected) Subcode read clock input pin. Schmidt input. (Be sure to connected to 0V when not in use.)
I
Pin outputting the 7.35 kHz sync signal which is generated by dividing frequency of crystal
O
oscillator. (Not connected) Subcode Q output standby output pin.
O
Read/write control input pin. Schmidt input.
I
Subcode Q output pin.
O
Command input pin from microprocessor.
I
Command input read clock or subcode read input clock from SQOUT pin
I
LC78622 reset input pin. Set this pin to L once when the main power is turned on. (Pull down)
I
Test signal output pin. Use this pin as open (normally L output). (Not connected)
O 60 61 62
63
64
16M
4.2M T5
______
CS
T1
16.9344 MHz output pin. (Not connected)
O
4.2336 MHz output pin.
O
Test signal input pin with built-in pull-down resistor. Be sure to connect to 0V.
I
Chip select signal input pin with built-in pull-down resistor. Be sure to connect to 0V while it is
I
not controlling.
I
Test signal input pin without built-in pull-down resistor. Be sure to connect to 0V.
-25-
Page 26
IC DESCRIPTION-3/3 (LC865516A-5P16)-1/2
Pin No. Pin Name I/O Description
1
SEG E
O
SEG E control.
10 11 12 13 14 15 16 17 18
2 3 4 5 6 7 8 9
SEG F
SEG G
NC
I-RES
XT1 (IN)
NC
XT2(OUT)
VSS
CF1(IN)
CF2(OUT)
VDD I-KEY0 I-KEY1
I-MOTOR
I-CD SW O-SHIFT
NC
—
—
—
—
—
O
SEG F control.
O
SEG G control. Not connected.
I
Micro processor reset input. (Pull down)
I
Connected to an external 32.768 kHz crystal oscillator. Not connected.
O
Connected to an external 32.768 kHz crystal oscillator. GND.
I
Connected to an external 5.76 MHz ceramic filter.
O
Connected to an external 5.76 MHz ceramic filter. Microprocessor power supply (+5V).
I
Key AD input. (AD) (Pull up)
I
Key AD input. (AD) (Pull up)
I
Deck status input. (AD) (Pull up)
I
CD door switch status input. (Pull up)
O
Main clock shift output.
Not connected. 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35
O-BASS LED
O-QS CONT.
O-SFT LED
I-DRF
I-WRQ
NC
I-REM
O-CD ON
O-TU ON
O-P.CONT
NC
O-BEAT O-MUTE O-DIGIT
O-SEG RPEAT
O-COIN
I-SQOUT
—
— —
—
O
BASS LED ON/OFF control output. (Not connected)
O
Q sound LED ON/OFF control output. (Not connected) Not connected.
I
CD RF level detection input.
I
CD subcode Q standby input. Not connected. Remote control input. (Pull up)
O
CD power control output.
O
TU power control output.
O
The main power supply control output. Not connected.
O
Beat control.
O
Main mute output.
O
7-segment LED power supply control output.
O
REPEAT LED ON/OFF control output.
O
CD command output.
I
CD subcode Q input. 36 37 38 39 40 41
O-CQCK
O-RWC
O-DATA O-CD LED O-TU LED O-TA LED
O
CD command/CLK for subcode.
O
CD read/write control output.
O
Data output to M62349FP.
O
LED ON/OFF control output for the CD function.
O
LED ON/OFF control output for the TU function.
O
LED ON/OFF control output for the TA function. (Not connected)
-26-
Page 27
IC DESCRIPTION-3/3 (LC865516A-5P16)-2/2
Pin No. Pin Name I/O Description
42
NC
—
Not connected. 43 44 45 46 47 48
SEG DP
SEG A SEG B SEG C SEG D
NC
—
O O O O O
SEG DP control.
SEG A control.
SEG B control.
SEG C control.
SEG D control.
Not connected.
-27-
Page 28
MECHANICAL EXPLODED VIEW-1/1
11
10
12
A
A
54
13
14
PWB
A
G
15
16
17
PWB
A
26
25
27
28
29
30
31
57
E
A
33
61
PWB
52
55
A
51
A
E
56
59
PWB
B
K
50
A
32
H
B
21
C
24
23
22
7
C
53
34
A
7
35
36
37
38
39
62
A
A
7
ZZM-1
A
PLATE,PT
43
42
A
41
F
PWB
D
PWB
46
45
44
A
40
J
PLATE,ANT
D
A
I
47
A
PWB
PWB
A
PWB
48
49
58
7
60
3
2
4
A
7
A
7
A
18
20
19
9
8
5
6
60
1
A
-28-
Page 29
MECHANICAL PARTS LIST-1/1
REF. NO PART NO. KANRI DESCRIPTION
NO.
1 8A-CDA-062-010 WINDOW,CASS D<HTSC> 1 8A-CDA-072-010 WINDOW,CASS EZ L<HTLCC> 2 87-B00-010-010 BADGE,AIWA 30.5-5.2 S 2.5L 3 8A-CDA-003-110 LID,CASS<HTSC> 3 8A-CDA-069-110 LID,CASS EZ L<HTLCC>
4 8A-CDA-212-010 SPR-T,CASS 5 8A-CDA-042-010 WINDOW,LED LOW LH 6 8A-CDA-145-110 CABI ASSY,FRONT LOW HE L<HTLCC> 6 8A-CDA-054-110 CABI ASSY,FRONT LOW HR<HTSC> 7 8A-CDA-206-010 HLDR,SPKR
8 8A-CDA-020-110 KNOB,SL BAND<HTSC> 8 8A-CDA-154-110 KNOB,SL BAND HE L<HTLCC> 9 8A-CDA-148-010 WINDOW,TU HE L<HTLCC> 9 8A-CDA-046-110 WINDOW,TU HR<HTSC> 10 8A-CDA-007-010 LENS,LED
11 8A-CDA-019-110 KEY,VOL<HTSC> 11 8A-CDA-080-110 KEY,VOL EZ L<HTLCC> 12 8A-CDA-061-310 LID,CD D<HTSC> 12 8A-CDA-070-310 LID,CD EZ L<HTLCC> 13 8A-CDA-213-010 COVER, CHUCK
14 87-036-368-010 MAGNET 15 8A-CDA-207-110 HLDR,CHUCK 16 8A-CDA-150-010 BASE,CHUCK F/M 17 88-CD9-211-210 RING,CHUCK 18 8A-CDA-620-010 FF-CABLE,16P FR-MAIN
19 8A-CDA-208-110 HLDR,LED 20 8A-CDA-622-010 FF-CABLE,8P CD-FR 21 8A-CDA-016-110 KEY,CD<HTSC> 21 8A-CDA-078-110 KEY,CD EZ L<HTLCC> 22 87-063-165-010 OIL-DMPR 150
23 8A-CDA-017-110 KEY,MODE<HTSC> 23 8A-CDA-079-110 KEY,MODE EZ L<HTLCC> 24 88-CH6-220-010 CUSHION,CD A 25 8A-CDA-621-010 FF-CABLE,16P CD-RF 26 8A-CDA-012-110 CHAS,CD<HTSC>
26 8A-CDA-180-110 CHAS,CD EZ L<HTLCC> 27 87-036-389-010 SW,PUSH LOCK 28 8A-CDA-211-010 SPR-T,CD 29 8A-CDA-010-210 HANDL,ARM<HTSC> 29 8A-CDA-074-110 HANDL,ARM EZ L<HTLCC>
30 8A-CDA-011-210 HANDL,COVER<HTSC> 30 8A-CDA-075-210 HANDL,COVER EZ L<HTLCC> 31 87-NF8-220-010 DMPR,150 32 87-A91-857-010 ANT,ROD 5SEC709 33 8Z-CDB-169-010 PANEL,CD SANYO
34 8A-CDA-027-110 KEY,PAUSE<HTSC> 34 8A-CDA-088-110 KEY,PAUSE EZ L<HTLCC> 35 8A-CDA-026-110 KEY,STOP<HTSC> 35 8A-CDA-087-110 KEY,STOP EZ L<HTLCC> 36 8A-CDA-025-110 KEY,FF<HTSC>
REF. NO PART NO. KANRI DESCRIPTION
36 8A-CDA-085-110 KEY,FF EZ L<HTLCC> 37 8A-CDA-024-110 KEY,REW<HTSC> 37 8A-CDA-086-110 KEY,REW EZ L<HTLCC> 38 8A-CDA-023-110 KEY,PLAY<HTSC> 38 8A-CDA-084-110 KEY,PLAY EZ L<HTLCC>
39 8A-CDA-022-110 KEY,REC<HTSC> 39 8A-CDA-083-110 KEY,REC EZ L<HTLCC> 40 8A-CDA-221-010 SPR-P,REC 41 8A-CDA-220-010 PLATE,REC 42 8A-CDA-021-110 KNOB,RTRY TU<HTSC>
42 8A-CDA-082-110 KNOB,RTRY TU EZ L<HTLCC> 43 8A-CDA-013-010 POINTER,TU 44 8A-CDA-201-110 HLDR,TU 45 8A-CDA-216-110 GEAR,TU B 46 8A-CDA-203-110 GUIDE,GEAR
47 8A-CDA-202-110 GEAR,RELAY 48 8A-CDA-215-110 DRUM,TU 49 8A-CDA-147-110 CABI,REAR LOW HE L<HTLCC> 49 8A-CDA-038-110 CABI,REAR LOW LH<HTSC> 50 8A-CDA-005-110 LID,BATT<HTSC>
50 8A-CDA-071-110 LID,BATT EZ L<HTLCC> 51 8Z-CD5-634-010 COVER,AC SOCKET 52 8A-CDA-626-010 CONN ASSY,2P DOOR 53 8A-CDA-630-010 CONN ASSY,4P RPH 54 8A-CDA-633-010 CONN ASSY,4P SP
55 8A-CDA-631-010 CONN ASSY,4P TA-ME
!
56 87-A91-369-010 SW,AC SL 2 2 2 SDKGA41700
!
57 87-A60-178-010 JACK,AC E W/SW
58 88-CD6-661-010 HLDR,BAR ANT.
!
59 8A-CDA-613-010 PT,H 2.5W
60 8A-CH4-682-010 SPKR,10- 7OHM 61 M8-ZZK-E90-070 DA11T3C 62 87-064-185-010 HLDR,WIRE A 87-721-096-410 QT2+3-10 GLD B 87-751-104-410 VT2+3-30
C 8A-CK4-223-010 S-SCREW,CD D 87-751-097-410 SCREW 3X12 E 87-751-076-410 SCREW 2.6-12 F 8A-CDA-222-010 S-SCREW,CASS+2.6-4 G 87-253-033-110 SCREW,U+2-4
H 87-253-097-410 U+3-12 BLK I 87-261-073-410 V+2.6-6 J 87-751-096-410 VT2+3-10 GLD K 87-723-074-410 QT2+2.6-8 W/O SLOT BLK
NO.
-29-
Page 30
COLOR NAME TABLE
Basic color symbol Color Basic color symbol Color Basic color symbol Color
B Black C Cream D Orange G Green H Gray L Blue
LT Transparent Blue N Gold P Pink
R Red S Silver ST Titan Silver T Brown V Violet W White
WT Transparent White Y Yellow YT Transparent Yellow
LM Metallic Blue LL Light Blue GT Transparent Green LD Dark Blue DT Transparent Orange GM Metallic Green
YM Metallic Yellow DM Metallic Orange PT Transparent Pink
LA Aqua Blue GL Light Green
-30-
Page 31
TAPE MECHANISM EXPLODED VIEW-1/1
12
11
TERMINAL,LB1
A
2
10
9
4
3
1
8
14
7
55 56
6
5
13
53
15
19
17
16
21
20
22
27
24
18
26
25
23
LEVER,E OPEN
28
31
54
30
29
48
50
51
52
49
47
B
33
34
1
35
38
46
45 44
43
32
36
37
42
40
41
39
-31-
Page 32
TAPE MECHANISM PARTS LIST-1/1
REF. NO PART NO. KANRI DESCRIPTION
NO.
1 8Z-ZM1-254-210 SPR-C,REEL R 2 8Z-ZM1-225-110 GEAR,REEL R 3 8Z-ZM1-253-110 SPR-C,AUTO SENSOR 4 8Z-ZM1-217-110 LEVER,AUTO SENSOR 5 8Z-ZM1-212-110 LEVER,T-UP
6 8Z-ZM1-245-010 SPR-T,AUTO 7 8Z-ZM1-236-010 CLR,SLIP FF/REW 8 8Z-ZM1-252-010 SPR-C,FF/REW 9 8Z-ZM1-230-010 GEAR,SLIP FF/REW A 10 8Z-ZM1-266-010 FELT,FF/REW
11 8Z-ZM1-231-010 GEAR,SLIP FF/REW B 12 8Z-ZM1-213-010 LEVER,FF/REW 13 8Z-ZM1-209-110 LEVER,PAUSE 14 8Z-ZM1-222-010 LEVER,E-LOCK M 15 8Z-ZM1-256-010 SPR-P,PAUSE
16 8Z-ZM1-244-010 SPR-T,T-UP 17 8Z-ZM1-247-210 SPR-T,PINCH 18 8Z-ZM1-261-110 ROLLER ASSY,PINCH 19 8Z-ZM1-221-010 LEVER,PINCH 20 8Z-ZM1-205-210 LEVER,PLAY
21 8Z-ZM1-248-010 SPR-T,BRG 22 87-A90-403-110 HEAD,RPH MS15R 23 84-ZM2-227-310 SPR-C,AZIMUTH 24 8Z-ZM1-216-010 LEVER,AUTO 25 8Z-ZM1-246-010 SPR-T,AUTO 2
26 8Z-ZM1-233-010 GEAR,IDL REW 27 8Z-ZM1-208-010 LEVER,STOP 28 8Z-ZM1-207-010 LEVER,FF 29 8Z-ZM1-206-010 LEVER,REW 30 8Z-ZM1-211-110 LEVER,REC 2
REF. NO PART NO. KANRI DESCRIPTION
NO.
31 87-A91-533-010 HEAD,EH PH-K380 32 8Z-ZM1-215-010 LEVER,REC LOCK 33 87-A91-492-010 SW,LEAF MSW18560 34 8Z-ZM1-226-010 GEAR,REEL L 35 8Z-ZM1-241-010 SPR-T,PLAY
36 8Z-ZM1-220-010 LEVER,REC SENSOR 37 8Z-ZM1-249-010 SPR-T,FR 38 8Z-ZM1-242-110 SPR-T,FF/REW 39 8Z-ZM1-229-010 GEAR,CAM 40 8Z-ZM1-232-010 GEAR,IDL FF/REW
41 8Z-ZM1-234-010 FLY-WHL,ZZM-1 42 8Z-ZM1-267-010 SHAFT,CAPSTAN 2 43 8Z-ZM1-228-010 GEAR,SLIP T-UP B 44 8Z-ZM1-265-010 FELT,T-UP 45 8Z-ZM1-227-010 GEAR,SLIP T-UP A
46 8Z-ZM1-251-110 SPR-C,T-UP SLIP 47 8Z-ZM1-243-210 SPR-T,STOP/PAUSE 48 87-A91-531-010 MOT,MS15C2L 49 8Z-ZM1-271-010 PULLEY,MOT ZZM-1 50 8Z-ZM1-264-010 BELT,MAIN S
51 8Z-ZM1-260-010 SPR-P,CASETTE 52 8Z-ZM1-201-310 CHAS ASSY,ZZM-1 53 8Z-ZM1-255-110 SPR-T,E-LOCK 54 8Z-ZM1-214-010 LEVER,LOCK 55 8Z-ZM1-257-110 SPR-C,F/R
56 8Z-ZM1-275-010 W-L,1.47-4-0.25 A 84-ZM2-242-010 S-SCREW,AZ1-2-6.4 B 8Z-ZM1-270-110 V+2.6 ZZM-1
-32-
Page 33
CD MECHANISM EXPLODED VIEW-1/1
SF-P101NR
CHASSIS
SHAFT,SLIDE
B
B
1
2
A
A
3
SPINDLE MOTOR(M3)
MOTOR C,B
-33-
Page 34
CD MECHANISM PARTS LIST-1/1
REF. NO PART NO. KANRI DESCRIPTION
1 S2-121-A28-400 COVER GEAR 2 S2-511-A21-000 GEAR MIDDLE 3 S2-511-A21-100 GEAR,DRIVE A S1-PN2-03R-OSE SCR PAN PCS 2-3 B 87-261-073-410 SCR S-TPG FLT 2.6-6
ALL M8-ZZK-E90-070 DA11T3C
NO.
-34-
Page 35
ACCESSORIES/PACKAGE LIST-1/1
REF. NO PART NO. KANRI DESCRIPTION
1 8A-CDA-901-010 IB,H(ECA)FM
!
2 87-050-076-010 AC CORD SET ASSY,E
NO.
-35-
Page 36
2–11, IKENOHATA 1–CHOME, TAITO-KU, T OKYO 110, JAPAN TEL:03 (3827) 3111
H251701
Printed in Singapore
Loading...
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use