CDC-R917M
YZ
SERVICE MANUAL
STEREO CAR CD RECEIVER BASIC CD MECHANISM : CDC02AW2
• This Service Manual is the "Revision Publishing" and replaces "Simple Manual"
CDC-R917M <YZ>, (S/M Code No. 09-014-444-2T1).
S/M Code No. 09-015-444-2R1
REVISION
DATA
SPECIFICATIONS
RADIO SECTION
(FM)
Frequency Range: 87.5 MHz – 108 MHz (50-kHz steps)
Usable Sensitivity: 12.7 dBf
50 dB Quieting Sensitivity: 17.2 dBf
IF Rejection: 80 dB
Frequency Response: 30 Hz – 15,000 Hz
S/N Ratio: 63 dB
Stereo Separation: 35 dB at 1 kHz
Alternate Channel Selectivity: 70 dB
Capture Ratio: 3 dB
(MW)
Frequency Range: 531 kHz – 1,602 kHz (9-kHz steps)
Usable Sensitivity: 30 µV (30 dB)
(LW)
Frequency Range: 144 kHz – 288 kHz (1-kHz/9-kHz steps)
Usable Sensitivity: 30 µV (30 dB)
CD SECTION
Frequency Response: 17 Hz – 20 kHz +0/–3 dB
Dynamic Range: More than 80 dB
Channel Separation: More than 65 dB
S/N Ratio: More than 85 dB
Wow/Flutter: Not applicable
AUDIO SECTION
Max. Power Output: 50 W x 4 channels
AUX IN input
Input Sensitivity (Load Impedance) AUX IN: 300 mV (10 kΩ)
GENERAL
Power-Supply Voltage: 14.4 V (11 to 16 V allowable), DC,
negative ground
Load Impedance: 4 Ω
Tone Control: Bass ± 10 dB at 100 Hz, Treble ± 10 dB at 10 kHz
Preamp Output Voltage (Load Impedance): 4 V (10 kΩ)
Installation Size: 182 (W) x 53 (H) x 155 (D) mm
(71/4 (W) x 21/8 (H) x 61/8 (D) inches)
STEERING-WHEEL REMOTE CONTROL
Dimensions: Approx. 67 (W) x 26 (H) x 27 (D) mm
(23/4 (W) x 11/16 (H) x 11/8 (D) inches) (excluding holder)
Weight: Approx. 38g (1.33 oz.) (including holder, battery)
• Design and specifications are subject to change without notice.
– 2 –
PROTECTION OF EYES FROM LASER BEAM DURING SERVICING
Solder
This set employs laser. Therefore, be sure to follow carefully
the instructions below when servicing.
WARNING!!
WHEN SERVICING, DO NOT APPROACH THE LASER
EXIT WITH THE EYE TOO CLOSELY. IN CASE IT IS
NECESSARY TO CONFIRM LASER BEAM EMISSION.
BE SURE TO OBSERVE FROM A DISTANCE OF MORE
THAN 30cm FROM THE SURFACE OF THE OBJECTIVE LENS ON THE OPTICAL PICK-UP BLOCK.
s Caution: Invisible laser radiation when
open and interlocks defeated avoid
exposure to beam.
s Advarsel: Usynlig laserståling ved åbning,
når sikkerhedsafbrydere er ude af funktion.
Undgå udsættelse for stråling.
VAROITUS!
Laiteen Käyttäminen muulla kuin tässä käyttöohjeessa
mainitulla tavalla saataa altistaa käyt-täjän
turvallisuusluokan 1 ylittävälle näkymättömälle
lasersäteilylle.
VARNING!
Om apparaten används på annat sätt än vad som
specificeras i denna bruksanvising, kan användaren
utsättas för osynling laserstrålning, som överskrider
gränsen för laserklass 1.
CAUTION
Use of controls or adjustments or performance of procedures other than those specified herin may result in
hazardous radiation exposure.
ATTENTION
L’utillisation de commandes, réglages ou procédures
autres que ceux spécifiés peut entraîner une dangereuse
exposition aux radiations.
ADVARSEL
Usynlig laserståling ved åbning, når sikkerhedsafbrydereer
ude af funktion. Undgå udsættelse for stråling.
This Compact Disc player is classified as a CLASS 1
LASER product.
The CLASS 1 LASER PRODUCT label is located on the
rear exterior.
CLASS 1 LASER PRODUCT
KLASSE 1 LASER PRODUKT
LUOKAN 1 LASER LAITE
KLASS 1 LASER APPARAT
Precaution to replace Optical block
(PICK720)
Body or clothes electrostatic potential could
ruin laser diode in the optical block. Be sure
ground body and workbench, and use care the
clothes do not touch the diode.
1) After the connection, remove solder shown in
right figure.
PICK-UP Assy PWB
Solder
– 3 –
ELECTRICAL MAIN PARTS LIST
PART NO. DESCRIPTIONREF. NO. KANRI
NO.
IC
88-KT1-607-080 C-IC,SAA6579T
8Z-KT1-622-010 C-IC,LC75374E
8B-KCF-616-010 IC,TA8273H
87-A21-532-030 C-IC,LC75817W-8720
87-A90-951-010 RCR UNIT,SBX1971-52
88-KT1-606-080 IC,PST994D
87-A20-712-040 C-IC,BA6417F
8B-KC1-601-030 C-IC,UPD178018AGC-596
87-020-784-080 IC,TC4053BF
87-A21-467-040 C-IC,CXA2581N
87-A21-533-030 C-IC,CXD2587Q
87-A21-952-030 C-IC,UPD789026GB-A54-8ES
87-A21-161-040 C-IC,BA6392FP
TRANSISTOR
87-A30-287-040 C-TR,DTC114TKA
87-A30-289-040 C-TR,2SA1037AK(R)
89-324-122-040 C-TR,2SC2412KR
87-A30-283-040 C-TR,DTA114YKA
87-A30-288-040 C-TR,DTC114YKA
87-A30-290-010 TR,KTA1658(Y)
86-NFZ-664-040 C-TR,DTC143TKA
87-A30-291-010 TR,KTC4369(Y)
89-418-580-080 TR,2SD1858TV2
89-423-952-010 TR,2SD2395E
87-A30-248-040 C-TR,2SB1197KQ
87-A30-011-080 C-TR,DTB113ZK
87-A30-273-040 C-TR,DTC124EKA
DIODE
87-A40-250-040 C-DIODE,DAN217
87-070-136-080 ZENER,MTZJ5.1B
87-020-331-040 C-DIODE,DAN202K
87-A40-817-040 C-ZENER,STZ6.8N
87-001-783-080 DIODE,1N4002
87-A40-798-010 DIODE,1N5402 (3A/200V)
87-A40-624-080 ZENER,MTZJ10A
87-A40-509-080 ZENER,MTZJ6.8C
87-020-330-040 C-DIODE,DAP202K
87-A40-620-080 ZENER,MTZJ6.2A
MAIN C.B
ANT101 8Z-KT1-614-010 ANT,AW-002
C101 87-012-274-080 C-CAP,U 1000P-50 K B
C102 87-012-286-080 C-CAP,U 0.01-25 K B
C103 87-012-282-080 C-CAP,U 4700P-50 K B
C104 87-010-498-040 CAP,E 10-16 M 5L SRE
C105 87-010-787-080 CAP,U 0.022-25 K B
C106 87-010-787-080 CAP,U 0.022-25 K B
C107 87-012-274-080 C-CAP,U 1000P-50 K B
C108 87-010-787-080 C-CAP,U 0.022-25 K B
C109 87-010-831-080 C-CAP,U 0.1-16 Z F
C110 87-012-281-080 C-CAP,U 3900P-50 B
C111 87-012-286-080 C-CAP,U 0.01-25 K B
C112 87-010-831-080 C-CAP,U 0.1-16 Z F
C114 87-010-831-080 C-CAP,U 0.1-16 Z F
C115 87-010-831-080 C-CAP,U 0.1-16 Z F
C116 87-010-495-040 CAP,E 2.2-50 M 5L SRE
C117 87-012-286-080 C-CAP,U 0.01-25 K B
C118 87-012-278-080 C-CAP,U 2200P-50 K B
C119 87-010-490-040 CAP,E 0.1-50 M 5L MA
C120 87-012-282-080 C-CAP,U 4700P-50 K B
C121 87-012-278-080 C-CAP,U 2200P-50 K B
C122 87-012-274-080 C-CAP,U 1000P-50 K B
C123 87-012-286-080 C-CAP,U 0.01-25 K B
C125 87-010-786-080 C-CAP,U 0.018-25 K B GRM
DESCRIPTIONREF. NO. KANRI
PART NO.
NO.
C126 87-010-786-080 C-CAP,U 0.018-25 K B GRM
C127 87-012-358-080 C-CAP,S 0.47-10 Z F CM/CB
C128 87-012-358-080 C-CAP,S 0.47-10 Z F CM/CB
C151 87-012-336-080 C-CAP,U 330P-50 J SL
C152 87-010-495-040 CAP,E 2.2-50 M 5L SRE
C153 87-012-271-080 C-CAP,U 560P-50 K B
C154 87-010-787-080 C-CAP,U 0.022-25 K B
C155 87-012-182-080 C-CAP,U 27P-50 J CH
C156 87-012-183-080 C-CAP,U 30P-50 J CH
C157 87-010-831-080 C-CAP,U 0.1-16 Z F
C158 87-010-553-040 CAP,E 47-16 M 5L SRE
C301 87-010-497-040 CAP,E 4.7-35 M 5L SRE
C302 87-010-497-040 CAP,E 4.7-35 M 5L SRE
C303 87-010-494-040 CAP,E 1-50 M 5L SRE
C304 87-010-494-040 CAP,E 1-50 M 5L SRE
C305 87-012-280-080 C-CAP,U 3300P-50 K B
C306 87-012-280-080 C-CAP,U 3300P-50 K B
C307 87-010-787-080 C-CAP,U 0.022-25 K B
C308 87-010-787-080 C-CAP,U 0.022-25 K B
C309 87-010-494-040 CAP,E 1-50 M 5L SRE
C310 87-010-494-040 CAP,E 1-50 M 5L SRE
C311 87-A12-308-080 C-CAP,S 0.15-25 K B
C312 87-A12-308-080 C-CAP,S 0.15-25 K B
C313 87-A12-308-080 C-CAP,S 0.15-25 K B
C314 87-A12-308-080 C-CAP,S 0.15-25 K B
C315 87-010-494-040 CAP,E 1-50 M 5L SRE
C316 87-010-494-040 CAP,E 1-50 M 5L SRE
C317 87-010-831-080 C-CAP,U,0.1-16 Z F
C318 87-010-498-040 CAP,E 10-16 M 5L SRE
C321 87-010-555-040 CAP,E 100-10 M 5L SRE
C322 87-010-787-080 C-CAP,U 0.022-25 K B
C323 87-010-498-040 CAP,E 10-16 M 5L SRE
C324 87-010-498-040 CAP,E 10-16 M 5L SRE
C325 87-010-498-040 CAP,E 10-16 M 5L SRE
C326 87-010-498-040 CAP,E 10-16 M 5L SRE
C341 87-010-491-040 CAP,E 0.22-50 M 5L SRE
C342 87-010-491-040 CAP,E 0.22-50 M 5L SRE
C401 87-010-494-040 CAP,E 1-50 M 5L SRE
C402 87-A10-369-080 C-CAP,S 0.47-16 K B
C403 87-A10-369-080 C-CAP,S 0.47-16 K B
C405 87-010-759-080 C-CAP,U 0.1-25 Z F
C406 87-010-759-080 C-CAP,U 0.1-25 Z F
C407 87-010-494-040 CAP,E 1-50 M 5L SRE
C408 87-010-494-040 CAP,E 1-50 M 5L SRE
C409 87-010-494-040 CAP,E 1-50 M 5L SRE
C410 87-010-494-040 CAP,E 1-50 M 5L SRE
C423 87-010-497-040 CAP,E 4.7-35 M 5L SRE
C424 87-010-497-040 CAP,E 4.7-35 M 5L SRE
C425 87-010-497-040 CAP,E 4.7-35 M 5L SRE
C426 87-010-497-040 CAP,E 4.7-35 M 5L SRE
C427 87-012-270-080 C-CAP,U 470P-50 K B
C428 87-012-270-080 C-CAP,U 470P-50 K B
C429 87-012-270-080 C-CAP,U 470P-50 K B
C430 87-012-270-080 C-CAP,U 470P-50 K B
C451 87-012-358-080 C-CAP,S 0.47-10 Z F CM/CB
C452 87-012-358-080 C-CAP,S 0.47-10 Z F CM/CB
C453 87-010-831-080 C-CAP,U 0.1-16 Z F
C454 87-012-286-080 C-CAP,U 0.01-25 K B
C461 87-010-787-080 C-CAP,U 0.022-25 K B
C501 87-012-358-080 C-CAP,S 0.47-10 Z F CM/CB
C502 87-012-358-080 C-CAP,S 0.47-10 Z F CM/CB
C503 87-012-358-080 C-CAP,S 0.47-10 Z F CM/CB
C504 87-012-358-080 C-CAP,S 0.47-10 Z F CM/CB
C505 87-012-270-080 C-CAP,U 470P-50 K B
C506 87-012-270-080 C-CAP,U 470P-50 K B
C507 87-012-270-080 C-CAP,U 470P-50 K B
C508 87-012-270-080 C-CAP,U 470P-50 K B
C510 87-010-498-040 CAP,E 10-16 M 5L SRE
C515 8A-KC7-623-000 CAP,E 2200-16 125 BT
C516 87-012-368-080 C-CAP,S 0.1-50 Z F
– 4 –
PART NO. DESCRIPTIONREF. NO. KANRI
C517 87-012-368-080 C-CAP,S 0.1-50 Z F
C519 87-010-494-040 CAP,E 1-50 M 5L SRE
C522 87-012-368-080 C-CAP,S 0.1-50 Z F
C701 87-012-278-080 C-CAP,U 2200P-50 K B
C704 87-012-368-080 C-CAP,S 0.1-50 Z F
C705 87-012-278-080 C-CAP,U 2200P-50 K B
C706 87-010-553-040 CAP,E 47-16 M 5L SRE
C707 87-010-787-080 C-CAP,U 0.022-25 K B
C708 87-010-553-040 CAP,E 47-16 M 5L SRE
C709 87-010-759-080 C-CAP,U 0.1-25 Z F
C713 87-010-759-080 C-CAP,U 0.1-25 Z F
C714 87-010-787-080 C-CAP,U 0.022-25 K B
C715 87-010-759-080 C-CAP,U 0.1-25 Z F
C716 87-010-759-080 C-CAP,U 0.1-25 Z F
C717 87-010-759-080 C-CAP,U 0.1-25 Z F
C718 87-010-759-080 C-CAP,U 0.1-25 Z F
C719 87-010-759-080 C-CAP,U 0.1-25 Z F
C720 87-010-787-080 C-CAP,U 0.022-25 K B
C723 87-010-759-080 C-CAP,U 0.1-25 Z F
C725 87-010-553-040 CAP,E 47-16 M 5L SRE
C751 87-012-368-080 C-CAP,S 0.1-50 Z F
C752 87-012-368-080 C-CAP,S 0.1-50 Z F
C753 87-012-368-080 C-CAP,S 0.1-50 Z F
C754 87-010-553-040 CAP,E 47-16 M 5L SRE
C901 87-016-039-090 CAP,DL 0.022F-5.5 Z 70 FM
C902 87-012-358-080 C-CAP,S 0.47-10 Z F CM/CB
C903 87-010-831-080 C-CAP,U 0.1-16 Z F
C904 87-010-787-080 C-CAP,U 0.022-25 K B
C905 87-012-180-080 C-CAP,U 22P-50 J CH
C906 87-012-182-080 C-CAP,U 27P-50 J CH
C907 87-010-831-080 C-CAP,U 0.1-16 Z F
C908 87-012-282-080 C-CAP,U 4700P-50 K B
C909 87-012-274-080 C-CAP,U 1000P-50 K B
C910 87-012-195-080 C-CAP,U 100P-50 J CH
C911 87-012-195-080 C-CAP,U 100P-50 J CH
C912 87-010-787-080 C-CAP,U 0.022-25 K B
C913 87-010-787-080 C-CAP,U 0.022-25 K B
C914 87-010-831-080 C-CHIP,U 1000P-50 K B
C915 87-012-274-080 C-CAP,U 1000P-50 K B
C916 87-010-787-080 C-CAP,U 0.022-25 K B
CON401 87-A61-219-010 CONN,20P H 52089-2020
CON402 87-A61-584-010 CONN,24P H 52089-2420
CON403 87-A61-583-010 CONN,16P H 52089-1620
CON701 8A-KT1-646-010 CONN ASSY,8P ISO-WHITE-B
CON702 8A-KT1-645-010 CONN ASSY,8P ISO-BLACK-B
CON751 87-A60-670-010 CONN,6P H 2MM JMT
F701 8Z-KC1-621-010 FUSE,15A 32V
!
FFC401 88-KC4-641-010 FF-CABLE,20P 1.0 90MM
FFC651 8B-KC1-603-010 F-CABLE,2P (PWB LED)
FFC671 8B-KC7-618-010 F-CABLE,2P MOT
J401 87-A61-224-110 JACK,PIN 4P XR-401
J402 8A-KC7-620-010 JACK,DIN 13 P SKDS1302
L101 87-003-143-080 COIL,4.7UH K LAL02
L102 8Z-KT1-619-010 COIL,68MH K7-D
L401 87-003-102-080 COIL,10UH J LAL02
L402 87-003-102-080 COIL,10UH J LAL02
L403 87-003-102-080 COIL,10UH J LAL02
L701 8B-KCF-615-010 FLTR,AMORPHOUS -CHOKE
L702 87-003-149-080 COIL,47UH J LAL02
L703 87-003-050-080 COIL,47UH K LAL04
SFR101 87-024-437-080 SFR,100K H RH063MC
TU101 8B-KC3-620-010 TU UNIT, FAE347-E21
X151 87-A70-091-010 VIB,XTAL 4.332MHZ CSA-309
X901 87-A70-175-010 VIB,XTAL 4.5MHZ AT-49
DISP C.B
C602 87-010-831-080 C-CAP,U 0.1-16 Z F
C603 87-010-831-080 C-CAP,U 0.1-16 Z F
C604 87-A10-504-080 C-CAP,U 0.047-16 K B
C605 87-012-199-080 C-CAP,U 220P-50 J CH
NO.
DESCRIPTIONREF. NO. KANRI
PART NO.
NO.
C606 87-A10-504-080 C-CAP,U 0.047-16 K B
C607 87-A10-504-080 C-CAP,U 0.047-16 K B
C608 87-A10-504-080 C-CAP,U 0.047-16 K B
C609 87-A10-504-080 C-CAP,U 0.047-16 K B
C610 87-010-805-080 C-CAP,S 1-16 Z F
C611 87-010-831-080 C-CAP,U 0.1-16 Z F
C612 87-010-831-080 C-CAP,U 0.1-16 Z F
C613 87-012-286-080 C-CAP,U 0.01-25 K B
CON601 87-A61-585-080 C-CONN,24P H 54548-2490
LCD701 8B-KC7-626-010 LCD,BKC-1/7
LED601 87-A91-355-040 C-LED,BR1112H-TR-RED
LED602 87-A91-355-040 C-LED,BR1112H-TR-RED
LED603 87-A91-355-040 C-LED,BR1112H-TR-RED
LED604 87-A91-355-040 C-LED,BR1112H-TR-RED
SW601 87-A90-001-080 C-SW,TACT SKQMAL
SW602 87-A90-001-080 C-SW,TACT SKQMAL
SW603 87-A90-001-080 C-SW,TACT SKQMAL
SW604 87-A90-001-080 C-SW,TACT SKQMAL
SW605 87-A90-001-080 C-SW,TACT SKQMAL
SW620 87-A90-001-080 C-SW,TACT SKQMAL
KEY C.B
C621 87-010-831-080 C-CAP,U 0.1-16 Z F
CON603 87-A61-586-080 C-CONN,16P V FLZT-SM1
L601 87-005-906-080 C-COIL,S 10.0UH K LK2125
L602 87-005-906-080 C-COIL,S 10.0UH K LK2125
L603 87-005-906-080 C-COIL,S 10.0UH K LK2125
LED611 87-A91-355-040 C-LED,BR1112H-TR-RED
LED612 87-A91-355-040 C-LED,BR1112H-TR-RED
LED613 87-A91-355-040 C-LED,BR1112H-TR-RED
LED614 87-A91-355-040 C-LED,BR1112H-TR-RED
LED615 87-A91-355-040 C-LED,BR1112H-TR-RED
LED616 87-A91-355-040 C-LED,BR1112H-TR-RED
LED617 87-A91-355-040 C-LED,BR1112H-TR-RED
LED618 87-A41-096-010 LED,E1L31-3B0A2 BLU
LED619 87-A40-813-240 C-LED,SEC1E01C BLU
LED620 87-A40-813-240 C-LED,SEC1E01C BLU
LED621 87-A40-813-240 C-LED,SEC1E01C BLU
LED622 87-A40-813-240 C-LED,SEC1E01C BLU
LED625 87-A91-355-040 C-LED,BR1112H-TR-RED
LED626 87-A91-355-040 C-LED,BR1112H-TR-RED
SW606 87-036-220-080 C-SW,TACT SKQAA
SW607 87-036-220-080 C-SW,TACT SKQAA
SW608 87-036-220-080 C-SW,TACT SKQAA
SW609 87-036-220-080 C-SW,TACT SKQAA
SW610 87-036-220-080 C-SW,TACT SKQAA
SW611 87-036-220-080 C-SW,TACT SKQAA
SW612 87-036-220-080 C-SW,TACT SKQAA
SW613 87-036-220-080 C-SW,TACT SKQAA
SW614 87-036-220-080 C-SW,TACT SKQAA
SW615 87-036-220-080 C-SW,TACT SKQAA
SW616 87-036-220-080 C-SW,TACT SKQAA
SW617 87-036-220-080 C-SW,TACT SKQAA
SW618 87-036-220-080 C-SW,TACT SKQAA
SENS C.B
CNA751 8B-KC7-617-010 CONN ASSY,6P EMP
FFC671 8B-KC7-618-010 F-CABLE,2P MOT
PS671 87-A92-061-080 C-SNSR,GP1S092 HCPI
SW671 87-A92-039-080 C-SW,PUSH ESE22MH24XQ
AUX C.B
FFC601 8B-KC1-602-010 F-CABLE,4P (AUX-W/S)
J601 87-A60-925-010 JACK,3.6 BLK ST W/SW
LED L C.B
LED605 87-A41-085-010 LED,NSPW315BS WHT
– 5 –
PART NO.
NO.
LED R C.B
LED606 87-A41-085-010 LED,NSPW315BS WHT
LED C.B
FFC651 8B-KC1-603-010 F-CABLE,2P (PWB LED)
LED651 87-A40-228-040 LED,SLR-342MG T31 GREEN
FLEX KEY C.B
8B-KC7-612-010 PWB,FLEX KEY
FLEX DISP C.B
8B-KC7-611-010 PWB,FLEX DISP
CD C.B
C803 87-A10-711-080 C-CAP,E 100-6.3 M MF
C804 87-012-274-080 CHIP CAP,U 1000P-50B
C805 87-A12-319-080 C-CAP,U 0.1-25 K B
C806 87-012-280-080 CAP, U 3300P-50
C808 87-A12-319-080 C-CAP,U 0.1-25 K B
C809 87-010-880-080 C-CAP,E 47-6.3 MF
C811 87-012-274-080 CHIP CAP,U 1000P-50B
C812 87-012-165-080 C-CAP,U 3P-50 C CH
C814 87-012-274-080 CHIP CAP,U 1000P-50B
C816 87-010-880-080 C-CAP,E 47-6.3 MF
C817 87-010-885-080 C-CAP,E 22-10 MF
C831 87-012-199-080 CAP 220P
C832 87-A10-504-080 C-CAP,U 0.047-16 K B
C833 87-012-268-080 C-CAP,U 330P-50 B
C834 87-012-198-080 CAP 180P
C835 87-A12-319-080 C-CAP,U 0.1-25 K B
C836 87-012-199-080 CAP 220P
C837 87-012-281-080 C-CAP,U 3900P-50 B
C838 87-A10-504-080 C-CAP,U 0.047-16 K B
C839 87-A10-711-080 C-CAP,E 100-6.3 M MF
C840 87-A12-319-080 C-CAP,U 0.1-25 K B
C841 87-012-286-080 CAP, U 0.01-25
C842 87-016-526-080 C-CAP,S 0.47-16 BK
C843 87-012-198-080 CAP 180P
C844 87-012-198-080 CAP 180P
DESCRIPTIONREF. NO. KANRI
PART NO.
NO.
C845 87-012-273-080 C-CAP,U 820P-50 B
C846 87-012-273-080 C-CAP,U 820P-50 B
C847 87-010-885-080 C-CAP,E 22-10 MF
C848 87-010-885-080 C-CAP,E 22-10 MF
C861 87-A12-319-080 C-CAP,U 0.1-25 K B
C862 87-A12-319-080 C-CAP,U 0.1-25 K B
C863 87-010-880-080 C-CAP,E 47-6.3 MF
C864 87-A12-319-080 C-CAP,U 0.1-25 K B
C881 87-A10-473-080 C-CAP,E 47-10 MF10FC(M)
C882 87-A12-319-080 C-CAP,U 0.1-25 K B
C884 87-012-274-080 CHIP CAP,U 1000P-50B
C885 87-A10-473-080 C-CAP,E 47-10 MF10FC(M)
C886 87-A12-319-080 C-CAP,U 0.1-25 K B
C887 87-A12-319-080 C-CAP,U 0.1-25 K B
C888 87-A12-319-080 C-CAP,U 0.1-25 K B
C889 87-A10-473-080 C-CAP,E 47-10 MF10FC(M)
C891 87-012-199-080 C-CAP,U 220P-50CH
C892 87-012-199-080 C-CAP,U 220P-50CH
C893 87-012-199-080 C-CAP,U 220P-50CH
C894 87-012-199-080 C-CAP,U 220P-50CH
C895 87-012-199-080 C-CAP,U 220P-50CH
C896 87-012-199-080 C-CAP,U 220P-50CH
C897 87-012-199-080 C-CAP,U 220P-50CH
C898 87-012-274-080 CHIP CAP,U 1000P-50B
C899 87-A10-711-080 C-CAP,E 100-6.3 M MF
CN801 87-A61-529-080 C-CONN,15P H FLZ-SM1-TB
CN891 87-A61-220-080 C-CONN,20P H 52271-2090
L801 87-A50-536-080 C-COIL,10UH K LQH3C24
L802 87-A50-536-080 C-COIL,10UH K LQH3C24
L831 87-A50-536-080 C-COIL,10UH K LQH3C24
L832 87-A50-536-080 C-COIL,10UH K LQH3C24
L833 87-A50-536-080 C-COIL,10UH K LQH3C24
L861 87-A50-536-080 C-COIL,10UH K LQH3C24
L881 87-A50-536-080 C-COIL,10UH K LQH3C24
S861 87-A91-627-080 SW,PUSH MPU10372MLBO
X831 87-A70-261-080 C-VIB,CER 16.93MHZ CSTCW-MX03T
X861 87-A70-333-080 C-VIB,CER 5.0MHZ CSTCR5M00G53
SENSOR C.B
SW1 87-A91-627-080 SWITCH
SW2 87-A91-627-080 SWITCH
DESCRIPTIONREF. NO. KANRI
CHIP RESISTOR PART CODE
Chip Resistor Part Coding
88
A
Resistor Code
Chip resistor
Wattage Type Tolerance
1/16W 1005 5% CJ
1/16W
1/10W
1/8W
1608
2125
3216
5%
5%
5%
Symbol
CJ
CJ
CJ
Figure
Value of resistor
Form
L
– 6 –
Dimensions (mm)
t
W
0.55
Resistor Code
108
118
128
LW t
1.0 0.5 0.35 104
1.6 0.8 0.45
2 1.25 0.45
3.2
1.6
: A
: A
TRANSISTOR ILLUSTRATION
C
B
E
B C E
KTA1658(Y)
KTC4369(Y)
E C B
2SD1858 TV2 2SA1037AK(R)
2SB1197KQ
2SC2412KR
DTA114YKA
DTB113ZK
DTC114TKA
DTC114YKA
DTC124EKA
DTC143TKA
B C E
2SD2395E
– 7 –
BLOCK DIAGRAM (CD)
CDC02AW2
OPTICAL BLOCK
(PICK720)
1
3
5
7
6
2
11
6
7
8
(CD RF AMP)
9
10
11
27
14
22
15
28
16
18
20
51
43
39
41
40
42
38
32 33
30 31 28 29
262575
1
2
3
4
5
6
7
8
9
18
19
20
24
72
36
40
35
34
33
32
31
25
30
29
22
24
21
20
52
1
11
(BAT)
13
28
29
26
23
17
18
19
16
CON401
M1
M3
(
(
)
)
13
12
14
15
1
2
13
12
16
17
(SERVO DRIVER)
26
27
21
23
24
15
10
20
19
5
4
9
(ACC)
5
3
11
M2
(
)
1
(LOADING
7
DRIVER)
3
4
5
8
WIRING 1 (MAIN / SENS / LED / FLEX KEY (2 / 2) / FLEX DISP (2 / 2)) <1 / 2>
32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
W1
A
B
C
D
W1
E
F
G
H
(TEST LAND)
I
J
K
L
M
N
O
PS671
+
_
P
Q
9
R
S
T
U
WIRING 2 (MAIN / LED) <2 / 2>
1 2 3 4 5 6 7 8 9 1011121314151617181920212223242526272829303132
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
S
T
U
10
SCHEMATIC DIAGRAM 1 (MAIN / SENS / LED)
11
WIRING 3 (DISP / KEY / AUX / LED L / LED R / FLEX KEY (1 / 2) / FLEX DISP (1 / 2)) <1 / 2>
32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
A
B
C
D
E
F
G
H
TO MAIN C.B CON403
VIA FLEX KEY C.B (2/2)
I
J
K
L
M
~
N
TO MAIN C.B CON402 VIA FLEX DISP C.B (2/2)
O
P
Q
12
R
S
T
U
WIRING 4 (DISP / KEY / AUX) <2 / 2>
1 2 3 4 5 6 7 8 9 1011121314151617181920212223242526272829303132
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
~
R
S
T
U
13
SCHEMATIC DIAGRAM 2 (DISP / KEY / AUX / LED L / LED R)
14
WIRING 5 (CD / SENSOR)
16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
1
5
10
11
12 15 2022
A
A
B
B
C
C
D
134
354044
34
33
30
25
23
578
D
E
E
F
F
G
G
H
H
I
I
J
J
30
1
5
25
10
20
15 16
15
21
25
30
35
40
41
15
45 50 55 60
21
20
15101520
80
75
70
65
61
15781014
22
25
28
K
K
L
L
M
M
N
N
O
O
P
P
Q
Q
R
1
15
R
S
S
T
T
U
U
15
SCHEMATIC DIAGRAM - 3 (CD / SENSOR)
K
4.9
OPTICAL BLOCK
(PICK720)
L
COIL
COIL
4.9
2.5
C898
1000P(B)
10
10
10
10
R808 22K
R809 22K
Q801,802
2SB1197KQ
(B)
(B)
Q802
C812
3P(CH)
R821 15K
1000P(B)
(B)
2.5
(B)
(CH)
(CH)
(CH)
(CH)
(CH)
5.2
(CH)
(CH)
8.2
4.9
(B)
(B)
(B)
8.2
R881
82K
8.2
TP59
TP58TP57
180P
3900P(B)
(B) 100/6.3
C899
100/6.3
0.01(B)
4.9
L833
4.9
(B)
(B)
(B)
SIGNAL:
PB
CONTROL
CON401 (FFC401)
8.2
16
LCD DISPLAY (LCD, BKC1/7)
SEGMENT WIRING
COMMON WIRING
17
IC BLOCK DIAGRAM
18
IC DESCRIPTION
IC, µPD178018AGC-596
Pin No. Pin Name I/O Description
1 FM/AM S–M I Input RDS AF signal and FM/AM S-meter signal input.
2 LEVEL IND I Voltage input for level indicator.
3 SEN 1 I Load sens detect input.
4 CD CONNECT I Connection check of CD changer.
5 CD DISP SEL O Signal output of communication timing with CD changer. H: TX, L: RX.
6 CD CLO O Synchronize clock signal output for transmission.
7 CD DI I Data signal input for reception.
8 CD DO O Data signal output for transmission.
9 CD CLI I Synchronize clock signal input for reception.
10 LCD STB/CE O LCD driver CE signal output.
11 CLK SEL O Clock selection for LCD driver.
12 LCD DI I Data signal input for LCD driver.
13 LCD DO O Data signal output for LCD driver.
14 LCD CLO O Synchronize clock signal output for LCD driver.
15 CD ACC CONT O ACC signal output for CD changer.
16 POWER MUTE O POWER MUTE signal output.
17 ST-BY MUTE O ST-BY MUTE signal output.
18 POWER CONT O POWER CONTROL signal output.
19 CONT 1 O LCD contrast: Control 1. (Not used)
20 CONT 2 O LCD contrast: Control 2. (Not used)
21 GND PORT – Ground for port.
22 VDD PORT – Power supply for port.
23 MUTE O Audio mute output.
24 BAND CONT O FM/AM power switch output. H: AM, L: FM.
25 RADIO CONT O Radio power switch output. L: Radio mode. (Not used)
26 RDS MODE O Hi output during RDS AF mode.
27 IF REQ O Request output for IF count signal.
28 AM IF I AM IF count signal input.
29 FM IF I FM IF count signal input.
30 VDD PLL – Power supply for PLL.
31 FM OSC I Input from FM station.
32 AM OSC I Input from AM station.
33 GND PLL – Ground for PLL.
34 EO0 O Error output from charge pump.
35 EO1 O Error output from charge pump.
36 GND – Ground.
37 LOC/DX O LOC/DX switch output during radio seek. H: LOC, L: DX.
38 SD/STIND I
39 PHONE MUTE I External mute control. L: -20dB Mute.
40 CDS CS O CS signal output.
41 CDS RESET O RESET signal output.
Station detect signal input during FM/AM seek. H: Detect station /
Stereo signal input during FM reception. H: Mono, L: ST.
– 19 –
Pin No. Pin Name I/O Description
42 CDS SLEEP O SLEEP signal output.
43 CDS STOP I STOP signal input. (Connected to GND through a resistor)
44 (CDS IN) I DISC insertion detect input.
45 SEN 2 I Load sens detect input.
46 BBE-2 I BBE input 1. (Not used)
47 BBE-1 I BBE input 2. (Not used)
48 MF.CONT O SLEEP signal control output.
49 MI–1 I Diode matrix input for default setting.
50 MI–2 I Diode matrix input for default setting.
51 MI–3 I Diode matrix input for default setting.
52 MO–1 O Diode matrix output for default setting. (Not used)
53 MO–2 O Diode matrix output for default setting.
54 MO–3 O Diode matrix output for default setting.
55 MO–4 O Diode matrix output for default setting.
56 PANCON1 O Panel control motor reverse drive output.
57 PANCON2 O Panel control motor forward drive output.
58 ACC IN I ON/OFF input for ACC (accessory power supply).
59 BEEP O BEEP output.
60 REMOTE I Remote control input.
61 E–VOL CE O CE output to electrical volume.
62 E–VOL DO O Data output to electrical volume.
63 E–VOL CLO O Clock output to electrical volume.
64 DRV CONT O Hi output during DRIVE mode.
65 RDS DI I RDS data input.
66 DFP IN I Front panel detection.
67 FLAPIN I OPEN/CLOSE detection of FLAP DFP. DFP IN: Enable when High.
68 RDS CLI I RDS clock input.
69 JACK IN I JACK detect input.
70 BATT IN I ON/OFF input for BATT.
71 RE-1 I Rotary encoder input 1. (Connected to GND through a resistor)
72 RE-2 I Rotary encoder input 2. (Connected to GND through a resistor)
73 S-REQ – S-REQ signal input for CDS.
74 REG CPU – CPU power-supply regulator.
75 GND – Ground.
76 X–OUT – System clock oscillator.
77 X–IN – System clock oscillator.
78 REG OSC – Oscillator circuit regulator.
79 VDD – System power supply.
80 RESET I System reset.
– 20 –
IC, LC75374E
Pin No. Pin Name I/O Description
1 RVR IN I 4dB volume control input. Must be driven at a low impedance.
2 R COM – 1dB volume control common pin. (Connected to GND through a capacitor)
For the connection of capacitors that compensate for bass and treble in the tone control circuits.
3 ~ 5 RT1 ~ RT3 – A high-frequency compensation capacitor must be connected between RT1 and RT2.
A low-frequency compensation capacitor must be connected between RT2 and RT3.
6 RT OUT O Tone control output.
7 RS IN I Super bass input. Must be driven at a low impedance.
8 NC – Connected to GND.
9 NC – Not connected.
10 RS3
11 RS OUT
12 FR IN I Fader input. Must be driven at a low impedance.
13 FR OUT
14 RR OUT
15 VSS – GND.
16 CL
17 DI
18 CE –
19 VREF –
20 RL OUT
21 FL OUT
22 FL IN I Fader input. Must be driven at a low impedance.
23 LS OUT
24 LS3
25 NC – Not connected.
O For the connection of RCH super bass compensation capacitors.
O Fader output. The front and rear sides can be attenuated independently.
I Serial data and clock input for control.
Chip enable. Data is written in the internal latch when the chip enable signal goes "L"
from "H", and each analog switch is activated. Data transfer is enabled at "H".
Generates a 1/2VDD power source. A capacitor must be connected between VREF and
GND as a troubleshooting against power ripples.
O Fader output. The front and rear sides can be attenuated independently.
O For the connection of LCH super bass compensation capacitors.
26 NC – Connected to GND.
27 LS IN I Super bass input. Must be driven at a low impedance.
28 LT OUT O Tone control output.
For the connection of capacitors that compensate for bass and treble in the tone control circuit.
29 ~ 31 LT3 ~ LT1 A high-frequency compensation capacitor must be connected between LT1 and LT2.
A low-frequency compensation capacitor must be connected between LT2 and LT3.
32 L COM – 1dB volume control common pin.
33 LVR IN I 4dB volume control input. Must be driven at a low impedance.
34 LSELO O Input selector output pin.
35 AUX (L)
36 CD (L)
37 TUN (L)
38 TP (L)
39 VDD – Power supply.
I Signal input pins.
– 21 –
Pin No. Pin Name I/O Description
40 TP (R)
41 TUN (R)
42 CD (R)
43 AUX (R)
44 RSELO O Input selector output pin.
I Signal input pins.
IC, LC75817W-8720
Pin No. Pin Name I/O Description
1 ~ 56 S1 ~ S56 O LCD segment output.
57 ~ 59 S57 ~ S59 O LCD segment output. (Not used)
60 S60 / COM10 O LCD segment output / LCD common driver output. (Not used)
61 COM9 O LCD common driver output. (Not used)
62 ~ 69 COM8 ~ COM1 O LCD common driver output.
70 , 71 KS1, KS2 O Key scan output. (Not used)
72 ~ 75 KS3 ~ KS6 O Key scan output.
76 ~ 80 KI1 ~ KI5 I Key scan input.
81 P-1
82 P-2
83, 84 P-3, P-4 O Not used.
85 VDD – Power supply.
86 VLCD – LCD power supply.
87 VLCD0 – LCD power supply.
88 VLCD1 I
89 VLCD2 I 1/2 bias voltage is applied to the LCD drive externally.
90 VLCD3 I
91 VLCD4 – Connected to GND.
92 VSS – GND.
93 TEST – Test pin. (Connected to GND)
94 OSC-OUT O
95 OSC-IN I
96 INT – Connected to VDD.
97 DO O Serial data interface pin; output data.
98 CE O Serial data interface pin; chip enable.
99 CL O Serial data interface pin; synchronization.
O Illumination driver output.
3/4 bias voltage is applied to the LCD drive externally.
1/4 bias voltage is applied to the LCD drive externally.
Resistor and capacitor are attached externally to form an oscillator circuit.
100 DI I Serial data interface pin; data transferred.
– 22 –
IC, CXD2587Q
Pin No. Pin Name I/O Description
1
SQSO
O
Sub-Q 80-bit and PCM peak level data output. CD TEXT data output.
10
11
12
13
14
15
16
17
18
O
–
I/O
O
O
O
O
O
I
Clock input for reading SQSO.
I
System reset. Reset at "L".
I
Muting input. Muted at "H".
I
Serial data input from CPU.
I
Latch input from CPU. Latches serial data at the trailing edge.
I
Clock input for serial data transfer from CPU.
SENS output to CPU.
I
Clock input for reading SENS serial data.
Power supply of digital circuits.
Input/output for anti-shock. (Connected to GND)
I
Microprocessor extended interface (input A). (Connected to GND)
I
Microprocessor extended interface (input B). (Connected to GND)
Microprocessor extended interface (output). (Not used)
WFCK output. (Not used)
WUGF output. MNT1 or RFCK is output when switched by command. (Not used)
XPCK output. MNT0 is output when switched by command. (Not used)
GFS output. MNT3 or XROF is output when switched by command.
2
3
4
5
6
7
8
9
SQCK
XRST
SYSM
DATA
XLAT
CLOK
SENS
SCLK
VDD
ATSK
SPOA
SPOB
XLON
WFCK
XUGF
XPCK
GFS
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
C2PO
SCOR
COUT
MIRR
DFCT
FOK
LOCK
MDP
SSTP
SFDR
SRDR
TFDR
TRDR
FFDR
FRDR
VSS
O
O
I/O
I/O
I/O
I/O
I/O
O
O
O
O
O
O
O
–
C2PO output.
Outputs "H" when Sub-code sync S0 or S1 is detected.
Track number count signal input/output. (Not used)
Mirror signal input/output. (Not used)
Defect signal input/output. (Not used)
Focus OK signal input/output.
Outputs "H" when GFS sampled by 460 Hz is "H"; "L" when GFS is "L" continuously for 8
samplings. Or, a signal is input when LKIN is "1".
Spindle motor servo control output.
I
Disc innermost edge detection signal input. (Connected to GND)
Sled drive output.
Sled drive output.
Tracking drive output.
Tracking drive output.
Focus drive output.
Focus drive output.
Ground of digital circuits.
35
36
37
38
39
TEST
TES1
XTSL
VC
FE
I
TEST pin. Normally grounded. (Connected to GND)
I
TEST pin. Normally grounded. (Connected to GND)
Crystal select input. "L" when 16.9344MHz crystal is used; "H" when 33.8688MHz crystal is
I
used. (Connected to GND)
I
Neutral voltage input.
I
Focus error signal input.
– 23 –
Pin No. Pin Name I/O Description
40
SE
I
Sled error signal input.
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
TE
CE
RFDC
ADIO
AVSS0
IGEN
AVDD0
ASYO
ASYI
BIAS
RFAC
AVSS3
CLTV
FILO
FILI
PCO
AVDD3
I
Tracking error signal input.
I
Neutral servo analog input.
I
RF signal input.
O
For test. Do not connect. (Not used)
–
Ground of analog circuits.
I
Constant current input for OP-AMP.
–
Power supply of analog circuits.
O
EFM full-swing output ("L": VSS; "H": VDD).
I
Asymmetry comparator voltage input.
I
Asymmetry circuit constant current input.
I
EFM signal input.
–
Ground of analog circuits.
I
VCO1 control voltage input for multiplication.
O
Filter output for master PLL (Slave: Digital PLL).
I
Filter input for master PLL.
O
Charge pump output for master PLL.
–
Power supply of analog circuits.
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
VSS
VDD
DOUT
LRCK
PCMD
BCK
EMPH
XVDD
XTAI
XTAO
XVSS
AVDD1
AOUT1
AIN1
LOUT1
AVSS1
–
Ground of digital circuits.
–
Power supply of digital circuits.
O
Digital output. (Not used)
O
D/A interface LR clock output f=Fs. (Not used)
O
D/A interface serial data output (2's COMP, MSB first). (Not used)
O
D/A interface bit clock output. (Not used)
Outputs "H" when disc to be played is applied with emphasis; "L" when disc to be played is not
O
applied with emphasis. (Not used)
–
Power supply of master clock.
I
Crystal oscillator input. External master clock is input to this pin.
O
Crystal oscillator output.
–
Ground of master clock.
–
Power supply of analog circuits.
O
Lch analog output.
I
Lch OP-AMP input.
O
Lch line output.
–
Ground of analog circuits.
74
75
76
77
78
79
80
AVSS2
LOUT2
AIN2
AOUT2
AVDD2
RMUT
LMUT
–
Ground of analog circuits.
O
Rch line output.
I
Rch OP-AMP input.
O
Rch analog output.
–
Power supply of analog circuits.
O
Rch "0" detection flag. (Not used)
O
Lch "0" detection flag. (Not used)
– 24 –
IC, CXA2581N
Pin No. Pin Name I/O Description
1
LD
O
APC-AMP output.
10
11
12
13
14
15
16
17
18
2
3
4
5
6
7
8
9
PD
EQ-IN
AC-SUM
GND
A
B
C
D
E
F
SW
DVCC
DVC
RFAC
FE
FEI
TE
I
APC-AMP input.
I
RFAC-system VCA/EQ block input.
O
RFAC-system RF SUM output.
–
Ground.
I
A-signal input.
I
B-signal input.
I
C-signal input.
I
D-signal input.
I
E-signal input.
I
F-signal input.
I
MODE switching signal input.
–
Power supply.
O
DVC output.
O
RFAC signal output.
O
Focus error signal output.
I
FE AMP virtual ground.
O
Tracking error signal output.
19
20
21
22
23
24
25
26
27
28
29
30
TE-BAL
CE
CEI
VCC
RFG
BST
VFC
RFC
VC
RFDCO
RFDCI
DC-OFST
I
TE balance adjustment. (Connected to VC).
O
Center error signal output.
I
CE AMP virtual ground.
–
Power supply.
I
RFAC-system VCA block low-frequency gain adjustment.
I
EQ boost level adjustment. (Connected to VC).
I
EQ cutoff frequency adjustment.
I
EQ cutoff frequency adjustment.
O
VC voltage output.
O
RFDC signal output.
I
RFDC AMP virtual ground.
I
RFDC signal output offset adjustment.
– 25 –
IC, µPD789026GB-A54-8ES
Pin No. Pin Name I/O Description
O
Loading motor reverse drive output. Active “H/L”.
O
Loading motor forward drive output. Active “H/L”.
I
Inner edge limit switch. Active “L”.
O
CD/CD-RW switching output. Active “H”.
O
Outputs “H” when power is turned on. Active “H”.
O
Mechanism microprocessor communication request. Active “L”.
I
SLEEP request from system microprocessor. Active “L”.
I
Chucking complete switch. Active “L”.
I
Disc loading switch. Active “L”.
I
8/12-cm check switch.
O
CD mechanism power control output. Active “H”.
–
Connected to GND.
–
Connected to GND.
–
For generating main system clock.
–
For generating main system clock.
10
11
12
13
14
15
1
2
3
4
5
6
7
8
9
LO-REV
LO-FWD
LIMT-SW
RF-SW
SV-CONT
SRQ
SLEEP
CHUCK-SW
LOAD-SW
8/12-SW
CD-ON
NC
IC
X2
X1
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
VSS
VDD
RESET
APC
LOCK
FOK
C2PO
CS
SCOR
SENS
SYS-DI
SYS-DO
SYS-CLK
GFS
SCLK
CLK-DSP
LAT-DSP
–
–
O
I/O
I/O
O
O
O
O
Ground.
Power supply.
I
System reset input.
Laser on/off switching output. Active “H/L”.
LOCK input/output.
Focus OK signal input/output.
I
C2PO input.
I
CS signal input. Active “L”.
I
Sub-code syncronize input.
I
SENS input.
I
System microprocessor serial data input.
System microprocessor serial data output.
I
System microprocessor serial syncronize clock input.
I
GFS input.
Outputs clock for reading SENS serial data.
Outputs clock for transferring DSP serial data.
DSP serial data latch output.
33
34
35
36
37
38
39
40
41 ~ 44
DATA-DSP
CD-MUTE
CD-RST
SQ-IN
NC
VDD
VSS
SQCK
NC
O
DSP serial data output.
O
Muting output. Active “H”.
O
CD reset output. Active “L”.
I
Sub-Q/PCM peak/level data input.
–
Not connected.
–
Power supply.
–
Ground.
O
Outputs clock for reading SQSO.
–
Not connected.
– 26 –
VOLTAGE CHART
IC151, SAA6579T
PIN NO. VOLT (V)
1, 2 2.25 ~ 2.70
3 2.52
4 2.50
5 5.00
60
7 2.50
8 2.55
9 ~ 11 0
12 5.0
13 2.15
14 2.55
15 2.51
16 2.52
IC301, LC75374E
PIN NO. VOLT (V)
1 ~ 7 4.32
80
9 0.07
10 ~ 14 4.32
15 0
16 ~ 18 –
19 ~ 24 4.32
25 0.035
26 0
27 ~ 38 4.32
39 8.36
40 ~ 44 4.32
IC501, TA8273H
PIN NO. VOLT (V)
1, 2 0
3 7.60
4 3.65
5 7.60
6 14.35
7 7.60
80
9 7.60
10 8.90
11, 12 1.40
13 0
14, 15 1.42
16 1.35
17 7.60
18 0
19 7.60
20 14.35
21 7.60
22 4.15
23 7.60
24 0
25 0.02
IC601, LC75817W-8720
PIN NO. VOLT (V)
1 ~ 56 3.30
57 ~ 61 –
62 ~ 69 3.30
70, 71 –
72 ~ 75 4.85
76 ~ 80 –
81 (4.85) {–}
82 (–){4.85}
83, 84 –
85 5.40
86 8.30
87 6.60
88 5.00
89 3.35
90 1.70
PIN NO. VOLT (V)
91 ~ 93 0
94 ~ 95 2.70
96 ~ 97 5.40
98 0.45
99 4.65
100 0.25
Note:
PIN 81, 82 ( ) = ILL1, { } = ILL2
IC602, SBX1971-52
PIN NO. VOLT (V)
10
2, 3 5.2
IC701, PST994D
PIN NO. VOLT (V)
1 8.70
20
3 4.35
IC751, BA6417F
PIN NO. VOLT (V)
1 0.24
2, 3 8.20
4, 5 –
6 3.64
7 0.25
80
IC901,
UPD178018AGC-596
PIN NO. VOLT (V)
1, 2 –
3 0.07
4–
5 4.90
6 ~ 9 –
10 0.24
11 0.58
12 4.32
13 0.12
14 4.70
15 (–) {1.90}
16 4.10
17 3.55
18 4.85
19, 20 –
21 0
22, 23 4.90
24 (–) {4.85}
25 4.90
26, 27 –
28, 29 0.03
30 4.90
31 (2.20) {0.65}
32 (0.35) {2.50}
33 0
34, 35 1.05
36 0
37 –
38 4.75
39 3.20
40, 41 4.90
42 4.85
43 –
44 4.30
45 ~ 57 –
58 5.00
59 –
60 5.22
61 ~ 64 –
65 (–) {0.70}
– 27 –
TU101, FAE347-E21
PIN NO. VOLT (V)
66, 67 5.1
68 (–) {2.5}
69 (0.70) {5.0}
70 4.30
71, 72 –
73 5.30
74 3.55
75 0
76 1.60
77 1.55
78 3.55
79, 80 4.90
Note:
PIN 24 ( ) = DX, { } = LO
PIN 31,32 ( ) = FM, { } = AM
PIN 65, 68 RDS
( ) = OFF, { } = ON
PIN 69 AUX JACK IN
( ) = OFF, { } = ON
IC903, TC4053BF
PIN NO. VOLT (V)
1 4.25
2 0.12
3 4.85
REF NO. ANODE CATHODE
LED 601 3.40 1.70
LED 602 1.70 0
LED 603 3.30 1.70
LED 604 1.70 0
LED 611 1.70 0
LED 612 3.35 1.70
LED 613 1.70 0
LED 614 3.50 1.8
LED 615 1.80 0.06
LED 616 3.50 1.8
LED 617 1.80 0.06
LED 618 9.0 5.50
LED 619 9.0 5.15
LED 620 9.0 5.15
LED 621 9.0 5.15
LED 622 9.0 5.15
LED 625 3.40 1.70
LED 626 5.0 3.35
LED 651 2.00 0
PIN NO. FM AM
1 ~ 3 – –
4 7.67 0.28
500
6 1.29 ~ 7.45 1.29 ~ 7.45
7, 8 0 0
9 1.60 8.75
10 0 0
11 0.12 0.23
12 8.05 0.03
13 8.26 8.15
14 2.2 ~ 3.68 2.2 ~ 3.68
15 0 0
16, 17 3.33 3.33
18 0 0
19, 20 – –
21 1.58 0.01
22 0.04 4.73
23 0.88 1.05
24 4.0 1.16
25 8.26 8.15
26 1.14 0.05
4 4.70
5 4.55
6 ~ 8 0
9 ~ 11 0.55
12 4.90
13 0.05
14 4.30
15 0.12
16 4.90
– 28 –
REF NO. DX LO
Q 101
B––
C 7.14 0.30
E00
REF NO. OFF ON
Q 401
B00
C 0.04 0.04
E 0.03 0.03
REF NO. OFF ON
Q 462
B – 1.90
C 14.4 0.02
E00
REF NO. VOLT(V)
Q 708
B 6.25
C 13.30
E 5.60
Q 102
B 9.0 8.30
C 0.50 8.90
E 9.00 9.00
Q 103
B 8.75 0.04
C 9.00 9.00
E 8.0 –
Q 104
B 4.8 –
C 8.75 0.04
E00
Q 105
B 1.05 1.00
C 0.65 2.2
E 0.60 0.01
Q 106
B 0.60 0.61
C 0.65 2.2
E00
Q107
B 1.14 0.58
C 1.29 8.0
E 0.64 –
Q108
B 0.64 0.30
C 1.29 8.0
E00
REF NO. OFF ON
Q 341
B – 4.10
C––
E00
Q 342
B – 4.10
Q402
B 4.85 4.85
C 0.035 0.035
E00
Q 403
B – 3.65
C––
E00
Q 404
B – 3.65
C––
E00
Q405
B – 3.65
C––
E00
Q406
B – 3.65
C––
E00
REF NO. VOLT (V)
Q109
B–
C–
E0
Q 451
B 1.50
C 4.70
E 0.90
REF NO. OFF ON
Q 461
B 14.4 0.02
C 0.15 14.30
E 14.4 14.4
REF NO. OFF ON
Q 611
B – 0.75
C – 0.06
E0 0
Q 612
B – 4.80
C 9.0 0.8
E – 0.75
Q613
B 4.85 –
C 0.80 9.0
E 0.75 –
Q614
B 0.75 –
C 0.09 –
E0 0
Q615
B 0.75 –
C 0.09 –
E0 0
REF NO. VOLT(V)
Q 701
B 13.60
C 14.30
E 14.35
Q 702
B 4.0
C 0.06
E0
Q704
B 9.70
C 14.35
E 9.0
Q 709
B 8.85
C 14.35
E 8.20
Q710
B 9.40
C 14.35
E 8.80
Q711
B 8.75
C 9.40
E 9.45
Q712
B 2.25
C–
E0
Q713
B 5.60
C 8.20
E 5.00
Q715
B 3.00
C–
E0
Q716
B–
C 5.60
E 5.60
C––
E00
– 29 –
CD TEST MODE
1. Disassembly
1. Remove COVER TOP / COVER BOTTOM.
2. Remove the screws (as shown by arrows in Fig-1) of CD
mechanism. See Fig-1.
2. Service Position
Check the function with the mechanism is set to a stable
position. (Use a tool such as PLATE). See Fig-2.
Fig-1
3. Test Mode
1. Starting the CD Test Mode
1) Short-circuit the TEST land (TP904 - as shown by arrow
in Fig-3) of the MAIN PWB, using solder. See Fig-3.
2) Connect the ACC (red) and BACKUP (yellow) wire of
the power supply/speakers connector to the positive
(+) terminal of the Power Supply device and the
Ground (black) wire to the negative (–) terminal.
3) Adjust the voltage applied to the Power Supply device
to 14.5V and then turn on the power.
The test mode starts, and the LCD are all lit. See Fig-4.
2. Exiting the CD Test Mode
1) Turn off the power of the Power Supply device.
2) Remove all the wires from the power supply/speakers
connector.
3) Remove the solder of the TEST land (TP904) of the
MAIN PWB.
Fig-2
IC901
Fig-3
Fig-4
– 30 –
3. CD Test Mode Functions
Mode
Start Mode All lights are lit. Test mode starts.
Button for
Activation
Display Operation Contents
Load/Unload
EJECT VCC on
Search RNDM Continuous focus search. APC circuit check
Mode
Play Mode REP 1 TOC READING Normal playback. Focus servo
Traverse INT Track No. and play Pause status Tracking servo OFF
Mode
STOP REP All lights are lit. Standby status All servo OFF
Sled Mode
• During search mode check, do not insert a disc.
• Press the REPEAT button to exit each mode.
6
5
3
4
TUNE
All lights are lit. Checking All servo off
Laser on
PU lens repeats full swings. (Note 1) Laser current measurement
Focus error waveform check
Track No. If TOC READ is unavailable, the Tracking servo
Play time display search mode function is on. CLV servo
Level display Sled servo
time are displayed
Laser ON/OFF
All lights are lit. Pickup moves to the Sled servo
outermost track. Mechanism function check
Pickup moves to the
innermost track.
Note 1: When the focus search mode is repeated more than 10 minutes, the driver IC may generate heat, activating the protection
circuit to stop the CD function. If this happens, turn off the power, wait for 10 minutes to release heat before restarting.
– 31 –
ADJUSTMENT
1. RDS Adjustment
• Instrument Settings : 98 MHz
µV (EMF)
31dB
1 kHz (Modulation Frequency)
45 kHz DEV
• Test point : IC901 1 pin
• Adjustment location : SFR101
Method : Set to FM 98.0 MHz and adjust SFR101 so that the
test point is 2.0 ± 0.2 V.
– 32 –
MECHANICAL EXPLODED VIEW 1 / 1
10
9
53
PWB
3
2
16
4
SH LCD
LCD
1
6
PWB
17
8
7
5
15
14
13
A
10
54
12
37
B
I
SH L-BT 18
18
J
SH CABI REAR
A
11
53
E
26
36
35
PWB
23
C
24
D
39
32
E
H
PWB
36
38
L
D
D
21
22
F
25
27
G
G
31
MOT FF-050SK
19
C
C
F
28
F
33
34
C
F
30
42
20
29
E
43
I
I
J
CDC02AW2
46
J
O
47
J
J
L
48
PWB
HLDR
CD-AC
I
45
44
K
K
HLDR
P-IC-AC
L
N
M
K
PANEL HT-SINK
51
52
40
L
41
SH,PWB
J
I
P
50
K
E
CDC-R917M YZSTF
(FileName:CDCR917M.EPS)
13/4/28 BKC-1
49
– 33 –
MECHANICAL PARTS LIST 1 / 1
PART NO. DESCRIPTIONREF. NO. KANRI
NO.
1 8B-KC1-001-010 WINDOW,LCD R917M
2 8B-KC7-001-010 CABI,FRONT HIGH
3 8B-KC7-004-010 BTN,+/ 4 8B-KC7-005-010 BTN,MUTE
5 8B-KC7-006-010 BTN,TWIN
6 8B-KC7-204-010 CASE,LCD
7 8B-KC7-202-010 LENS,LCD
8 8B-KC7-201-010 PLATE,LENS BOTTOM
9 8B-KC7-002-010 CABI,REAR
10 8B-KC7-222-010 PLATE,MAGNET
11 8B-KC7-025-010 PANEL,BOARD
12 8B-KC7-611-010 PWB,FLEX DISP
13 8B-KC7-007-010 CABI,FRONT AL
14 8B-KC7-008-010 CABI,BTN PANEL B
15 8B-KC1-002-010 BTN,P-SET YZ
16 8B-KC7-015-010 LENS,BER
17 8B-KC7-207-010 PLATE,PANEL A’SSY
18 8B-KC7-612-010 PWB,FLEX KEY
19 8A-ZL2-211-010 HLDR ASSY MOT
20 8A-ZL2-241-010 GEAR,WORM
21 8A-ZL2-242-010 WORM-WHL
22 8A-ZL2-243-010 GEAR,L-1
23 8B-KC7-209-010 HLDR,SP-L
24 8A-ZL2-231-010 LEVER ASSY GEAR L
25 8A-ZL2-221-010 LEVER ASSY L
26 8A-ZL2-201-010 FRAME ASSY MAIN
27 8A-ZL2-246-010 GEAR CAM L
28 8A-ZL2-236-010 LEVER ASSY GEAR R
29 8A-ZL2-226-010 LEVER ASSY R
30 8B-KC7-210-010 HLDR,SP-R
31 8A-ZL2-247-010 GEAR CAM R
32 8A-ZL2-244-010 GEAR,L-2
33 8A-ZL2-251-010 SHAFT COUNTER
34 8A-ZL2-245-010 GEAR R
35 8B-KC7-208-010 COVER, DUST
DESCRIPTIONREF. NO. KANRI
PART NO.
NO.
36 85-ZL3-203-010 MAGNET,ACU
37 8B-KC7-021-010 CABI,BASE MAIN
38 8B-KC7-022-010 LENS,CD
39 8B-KC1-603-010 F-CABLE,2P (PWB LED)
40 8B-KC7-023-010 CABI,BASE AROUND
41 8B-KC1-213-110 CHAS,SIDE L-BC
42 8B-KC7-212-010 HLDR,TR2-B
43 8Z-KC1-256-010 COVER, BOTTOM RDS
44 8B-KC7-211-010 HLDR,MECHA
45 8B-KC7-246-010 HLDR,ISO WIRE B
46 88-KC4-641-010 FF-CABLE, 20P 1.0 90MM
47 8A-KC7-255-010 SPR-C,WIRE
48 8B-KC7-217-010 HLDR,MECHA FR
49 8B-KC1-214-110 CHAS,SIDE R-BC
50 8B-KC1-201-010 COVER, BT RDS
51 8B-KC7-024-010 CABI,TRIM
52 8Z-KC1-231-110 HLDR,HALF -C
53 8B-KC7-215-010 SHAFT,FLAP L/R
54 8B-KC7-218-010 TERMINAL,PWB
A 8Z-KC1-253-010 S-SCREW,PT 2*8 BH+ BLK
B 87-B10-335-010 VTT+1.7-4 W/O
C 87-261-032-210 V+2-3
D 87-067-800-010 W-P,1.5-3.5-0.25SLT
E 87-251-070-410 U+2.6-3
F 87-078-018-010 W-P,1.55-3.5-0.25C-WT
G 87-067-272-010 W-P,2.1-4-0.25SLIT
H 8Z-KC1-254-010 S-SCREW,PT 2*5 BH+ BLK
I 87-B10-216-010 U+2.6-4.0 ZINC BLK (BH M2.6)
J 8Z-KC1-251-010 S-SCREW,TH2.6-4.0-0.8
K 87-251-073-410 SCREW,U+2.6-6
L 87-B10-336-010 VTT+2.6-6 W/O
M 87-B10-259-010 UT2+3.0-10.0 W/O SLOT (BH TAP)
N 87-251-096-410 U+3-10
O 88-ZG5-317-010 S-SCREW,8ZG5S+2-4 W/O
P 87-432-903-010 WASHER,WTE 2.6
COLOR NAME TABLE
Basic color symbol Color Basic color symbol Color Basic color symbol Color
B Black C Cream D Orange
G Green H Gray L Blue
LT Transparent Blue N Gold P Pink
R Red S Silver ST Titan Silver
T Brown V Violet W White
WT Transparent White Y Yellow YT Transparent Yellow
LM Metallic Blue LL Light Blue GT Transparent Green
LD Dark Blue DT Transparent Orange GM Metallic Green
YM Metallic Yellow DM Metallic Orange PT Transparent Pink
LA Aqua Blue GL Light Green HT Transparent Gray
– 34 –
CD MECHANISM EXPLODED VIEW 1 / 1
G
4
SENSOR,PWB
56
CORD 3P
51
1
B
A
CHUCK
5
6
7
55
10
60
57
52
SHEET
38
42
43
41
58
A
A
(+)P.PRECISION SCREW M1.7-2.2
8
13
9
7
55
15
11
ARM,SHEET
37
2
3
12
14
16
23
C
26
27
36
59
33
E
41
40
34
39
62
DISC,SHEET
19
21
20
24
25
MOTER LEAD A
MOTER LEAD B
30
31
32
A
A
D
35
61
17
18
18
22
28
29
17
54
A
53
50
MOTER LEAD 2P
47
47
A
49
46
F
48
44
45
CDC02AW2
(FileName:EXP.EPS)
13/2/20
– 35 –
CD MECHANISM PARTS LIST 1 / 1
PART NO. DESCRIPTIONREF. NO. KANRI
1 S1-100-510-130 COVER TOP
2 S1-100-510-090 LEVER RELEASE
3 S1-100-510-180 ARM START SET
4 S1-100-520-220 LEVER,SENSOR
5 S1-100-540-070 SP LEVER SENSOR
6 S1-100-520-050 DISC ARM L
7 S1-100-530-260 ROLLER ARM DISC
8 S1-100-540-040 SP ARM DISC
9 S1-100-520-060 DISC ARM R
10 S1-100-570-760 SW,LOAD MPU10853MLB2
11 S1-100-520-230 GUIDE TOP
12 S1-100-510-070 PLATE CLAMPER
13 S1-100-520-040 CLAMPER
14 S1-100-740-020 SP ARM CHUCK
15 S1-100-510-030 ARM CHUCK
16 S1-100-740-040 SP ARM CHUCK(R)
17 S2-181-600-50D PSW,1.6-5-0.25 (CUT)
18 S1-100-750-020 LOLLER LOADING
19 S1-100-570-070 SW,INNER
20 S1-100-570-140 LEAD SW A
21 S1-100-570-150 LEAD SW B
22 S1-100-530-060 SHAFT ROLLER
23 S1-100-740-010 SP FEED
24 S1-100-510-110 GUIDE,SPG
25 S1-100-720-050 GUIDE 720
26 S1-100-770-340
27 S1-100-770-360
28 S1-100-540-100
29 S1-100-520-240
30 S1-100-270-030
31 S1-100-520-110 GEAR MOTOR FEED
32 S1-100-520-190 CASE,MOTOR
33 S1-100-730-010 SCREW,FEED
34 S1-100-520-090 GEAR,FEED A
35 S1-100-520-300 GEAR FEED B
NO.
PICK FPC(720)
PICK720
SP LEVER UP
LEVER,UP
MOTOR,MAIN FF-030PK
DESCRIPTIONREF. NO. KANRI
PART NO.
NO.
36 S1-100-520-170 LEVER,R
37 S1-100-520-140 GEAR H CAM
38 S1-100-540-080 SP SUB DAMPER
39 S1-100-510-080 ARM,R
40 S1-100-520-180 LEVER,LOCK
41 S1-100-540-030 DAMPER SP
42 S1-100-520-130 GEAR LOAD
43 S1-100-520-120 GEAR L H
44 SX-100-710-130 CHASSIS ASSY(AW2)
45 S1-100-520-160 LEVER,KICK
46 S1-100-520-270 LEVER,SUB KICK
47 S1-100-760-010 DAMPER ASSY
48 S1-100-510-060 BRACKET,L M
49 S1-100-520-200 MOTOR WORM
50 S1-100-770-080 MOTOR LOAD
51 S1-100-540-090 SP GEAR SUB
52 S1-100-520-030 GEAR SUB CAM
53 S1-100-520-250 LEVER,SW
54 S1-100-520-210 GEAR,ROLLER
55 S1-100-530-250 PIN ARM DISC
56 S1-100-520-020 GEAR CAM
57 S1-100-740-030 SP LOCK P.B
58 S1-100-710-080 PLATE L
59 S1-100-710-090 GUIDE PICK 720
60 S1-100-720-030 LOCK,P.B
61 S1-100-730-030 COLLAR
62 SZ-100-710-010 PICK BASE GROSS ASSY
A S1-100-550-030 SCREW,XP
B S2-139-140-40P B-TYPE M1.4-4
C S2-134-170-80P S-TYPE WITH GUIDE M1.7-8
D S2-103-200-40P (+)P.PRECISION SCREW M2.0-4.0
E S3-132-140-30P S-TYPE WITH GUIDE M1.4-3
F S2-101-200-25P (+)P.PRECISION SCREW M2.0-2.5
G S2-132-200-40P S-TYPE WITH GUIDE M2-4
– 36 –
ACCESSORIES / PACKAGE LIST
PART NO.
NO.
1 8B-KC1-901-010 IB,YZ(9L)R917M
2 8B-KCF-906-110 IB,INST,YZ,YV(9L,R)-I
3 87-B10-141-010 NUT,5 TYPE-2
4 87-B10-143-010 UT1+5-15 W/O SLOT
5 87-B10-144-010 W,5.2-10-0.5
6 87-B10-145-010 W-SPR,5.3-8.5-1.5
7 8Z-KC1-231-110 HLDR,HALF-C
8 8Z-KC1-232-010 KEY,REMOVE-C
9 8Z-KC1-235-010 HLDR,REAR MTG
10 8Z-KC1-244-010 S-SCREW,5*6 TH+ TAPPING ST
11 8Z-KC1-250-010 S-SCREW,HEXAGON
*12 R8-BZR-191-040 BZR-1 RC3YZNF
*NOTE: This remote controller is not an accessory part.
It is an individual model.
DESCRIPTIONREF. NO. KANRI
– 37 –
2–11, IKENOHATA 1–CHOME, TAITO-KU, TOKYO 110, JAPAN TEL:03 (3827) 3111
Printed in Singapore2000068 0251431
Loading...