Page 1
CDC-MP32
YU
SERVICE MANUAL
STEREO CAR CD RECEIVER BASIC CD MECHANISM : CDC02AW2
• This Service Manual is the “Revision Publishing” and replaces
“Simple Manual” of CDC-MP32 <YU>, (S/M Code No. 09-014-443-9T1).
S/M Code No. 09-017-443-9R1
REVISION
DATA
Page 2
SPECIFICATIONS
RADIO SECTION
(FM)
Frequency Range 87.5 MHz – 108 MHz (100 kHz steps)*
87.5 MHz – 108 MHz (50 kHz steps)*
Usable Sensitivity 12.7 dBf
50 dB Quieting Sensitivity 17.2 dBf
IF Rejection 80 dB
Frequency Response 30 Hz – 15,000 Hz
S/N Ratio 63 dB
Stereo Separation 35 dB at 1 kHz
Alternate Channel Selectivity
70 dB
Capture Ratio 3 dB
(AM)
Frequency Range 530 kHz – 1,710 kHz (10 kHz steps)*
531 kHz – 1,602 kHz (9 kHz steps)*
Usable Sensitivity 30 µV (30 dB)
9k 10k
* Set the frequency increment for your area using the switch on the
bottom of the unit. (The switch is factory-set to the 10k position [for the
U.S.A.])
CD SECTION
Frequency Response 17 Hz – 20 kHz +0/–3 dB
Dynamic Range More than 80 dB
Channel Separation More than 65 dB
S/N Ratio More than 85 dB
Wow/Flutter Not applicable
AUDIO SECTION
Max. Power Output 50 W x 4 channels
AUX IN input
Input Sensitivity (Load Impedance)
AUX IN 300 mV (10 kΩ)
GENERAL
Power-Supply Voltage 14.4 V (11 to 16 V allowable), DC,
Load Impedance 4 Ω
Tone Control Bass ± 10 dB at 100 Hz
Preamp Output Voltage (Load Impedance)
Installed Size 182 (W) x 53 (H) x 155 (D) mm
STEERING WHEEL REMOTE CONTROL
Dimensions Approx. 67 (W) x 26 (H) x 27 (D) mm
Weight Approx. 38 g (1.33 oz.)
• Design and specifications are subject to change without notice.
negative ground
Treble ± 10 dB at 10 kHz
2.2 V (10 kΩ)
1
(7
/4 (W) x 21/8 (H) x 61/8 (D) inches)
(23/4 (W) x 11/16 (H) x 11/8 (D) inches)
(excluding holder)
(including holder, battery)
– 2 –
Page 3
PROTECTION OF EYES FROM LASER BEAM DURING SERVICING
This set employs laser. Therefore, be sure to follow carefully
the instructions below when servicing.
WARNING!!
WHEN SERVICING, DO NOT APPROACH THE LASER
EXIT WITH THE EYE TOO CLOSELY. IN CASE IT IS
NECESSARY TO CONFIRM LASER BEAM EMISSION.
BE SURE TO OBSERVE FROM A DISTANCE OF MORE
THAN 30cm FROM THE SURFACE OF THE OBJECTIVE LENS ON THE OPTICAL PICK-UP BLOCK.
s Caution: Invisible laser radiation when
open and interlocks defeated avoid
exposure to beam.
s Advarsel: Usynlig laserståling ved åbning,
når sikkerhedsafbrydere er ude af funktion.
Undgå udsættelse for stråling.
VAROITUS!
Laiteen Käyttäminen muulla kuin tässä käyttöohjeessa
mainitulla tavalla saataa altistaa käyt-täjän
turvallisuusluokan 1 ylittävälle näkymättömälle
lasersäteilylle.
VARNING!
Om apparaten används på annat sätt än vad som
specificeras i denna bruksanvising, kan användaren
utsättas för osynling laserstrålning, som överskrider
gränsen för laserklass 1.
CAUTION
Use of controls or adjustments or performance of procedures other than those specified herin may result in
hazardous radiation exposure.
ATTENTION
L’utillisation de commandes, réglages ou procédures
autres que ceux spécifiés peut entraîner une dangereuse
exposition aux radiations.
ADVARSEL
Usynlig laserståling ved åbning, når sikkerhedsafbrydereer
ude af funktion. Undgå udsættelse for stråling.
This Compact Disc player is classified as a CLASS 1
LASER product.
The CLASS 1 LASER PRODUCT label is located on the
rear exterior.
CLASS 1 LASER PRODUCT
KLASSE 1 LASER PRODUKT
LUOKAN 1 LASER LAITE
KLASS 1 LASER APPARAT
Precaution to replace Optical block
(KSS-710A)
Body or clothes electrostatic potential could
ruin laser diode in the optical block. Be sure
ground body and workbench, and use care the
clothes do not touch the diode.
1) After the connection, remove solder shown in
right figure.
PICK-UP ASSY PWB
SOLDER
– 3 –
Page 4
ELECTRICAL MAIN PARTS LIST
PART NO. DESCRIPTIONREF. NO. KANRI
NO.
IC
8Z-KT1-622-010 C-IC,LC75374E
8B-KCF-616-010 IC,TA8273H
87-A21-532-030 C-IC,LC75817W-8720
87-A90-951-010 RCR UNIT,SBX1971-52
88-KT1-606-080 IC,PST994D
87-A20-712-040 C-IC,BA6417F
8B-KC6-621-030 C-IC,UPD178018AGC-598
87-020-784-040 C-IC,TC4053BF
87-A22-017-030 C-IC,UPD784216AYGC-110-8EU
87-A21-941-030 C-IC,UT62L1024LC-70LL
87-A21-621-010 C-IC,MAS3507D-G10
87-A21-624-040 C-IC,SN74AHC1G08 DCK
87-A21-599-010 C-IC,LC89513K
87-A21-942-030 C-IC,T15L256A-70P
87-A21-714-030 C-IC,DAC3550A-C2
87-A21-467-040 C-IC,CXA2581N
87-A21-533-030 C-IC,CXD2587Q
87-A20-905-040 C-IC,BA033FP
87-A21-190-040 C-IC,PQ20WZ1U
87-A21-728-040 C-IC,SN74LVC07A
87-A21-161-040 C-IC,BA6392FP
87-A20-712-040 C-IC,BA6417F
TRANSISTOR
87-A30-287-040 C-TR,DTC114TKA
87-A30-289-040 C-TR,2SA1037AK(R)
89-324-122-040 C-TR,2SC2412KR
87-A30-283-040 C-TR,DTA114YKA
87-A30-288-040 C-TR,DTC114YKA
87-A30-290-010 TR,KTA1658(Y)
86-NFZ-664-040 C-TR,DTC143TKA
87-A30-291-010 TR,KTC4369(Y)
89-418-580-080 TR,2SD1858TV2
89-423-952-010 TR,2SD2395E
87-A30-248-040 C-TR,2SB1197KQ
87-A30-011-080 C-TR,DTB113ZK
87-A30-273-040 C-TR,DTC124EKA
87-A30-455-040 C-TR,DTA144EKA
DIODE
87-A40-250-040 C-DIODE,DAN217
87-020-331-040 C-DIODE,DAN202K
87-A40-817-040 C-ZENER,STZ6.8N
87-001-783-080 DIODE,1N4002
87-A40-798-010 DIODE,1N5402
87-A40-624-080 ZENER,MTZJ10A
87-A40-509-080 ZENER,MTZJ6.8C
87-020-330-040 C-DIODE,DAP202K
87-A40-620-080 ZENER,MTZJ6.2A
87-070-136-080 ZENER,MTZJ5.1B
MAIN C.B
ANT101 8Z-KT1-614-010 ANT,AW-002
C101 87-012-274-080 CHIP CAP,U 1000P-50B
C102 87-012-286-080 C-CAP,U 0.01-25
C103 87-012-282-080 C-CAP,U 4700P-50
C104 87-010-498-040 CAP,E 10-16 GAS
C105 87-010-787-080 C-CAP,U 0.022-25
C106 87-010-787-080 C-CAP,U 0.022-25
C107 87-012-274-080 CHIP CAP,U 1000P-50B
C108 87-010-787-080 C-CAP,U 0.022-25
C109 87-010-831-080 C-CAP,U,0.1-16F
C110 87-012-281-080 C-CAP,U 3900P-50 B
C111 87-012-286-080 C-CAP,U 0.01-25
C112 87-010-831-080 C-CAP,U,0.1-16F
C114 87-010-831-080 C-CAP,U,0.1-16F
DESCRIPTIONREF. NO. KANRI
PART NO.
NO.
C115 87-010-831-080 C-CAP,U,0.1-16F
C116 87-010-495-040 CAP,E 2.2-50 GAS
C117 87-012-286-080 C-CAP,U 0.01-25
C118 87-012-278-080 C-CAP,U 2200P-50 B
C123 87-012-286-080 C-CAP,U 0.01-25
C125 87-A11-228-080 C-CAP,U 0.027-25 K B
C126 87-A11-228-080 C-CAP,U 0.027-25 K B
C127 87-012-358-080 C-CAP,S 0.47-10 F Z
C128 87-012-358-080 C-CAP,S 0.47-10 F Z
C301 87-010-497-040 CAP,E 4.7-35 GAS
C302 87-010-497-040 CAP,E 4.7-35 GAS
C303 87-010-494-040 CAP,E 1-50 GAS
C304 87-010-494-040 CAP,E 1-50 GAS
C305 87-012-280-080 C-CAP,U 3300P-50
C306 87-012-280-080 C-CAP,U 3300P-50
C307 87-010-787-080 C-CAP,U 0.022-25
C308 87-010-787-080 C-CAP,U 0.022-25
C309 87-010-494-040 CAP,E 1-50 GAS
C310 87-010-494-040 CAP,E 1-50 GAS
C311 87-A12-308-080 C-CAP,S 0.15-25 K B
C312 87-A12-308-080 C-CAP,S 0.15-25 K B
C313 87-A12-308-080 C-CAP,S 0.15-25 K B
C314 87-A12-308-080 C-CAP,S 0.15-25 K B
C315 87-010-494-040 CAP,E 1-50 GAS
C316 87-010-494-040 CAP,E 1-50 GAS
C317 87-010-831-080 C-CAP,U,0.1-16F
C318 87-010-498-040 CAP,E 10-16 GAS
C321 87-010-555-040 CAP,E 100-10 GAS
C322 87-010-787-080 CAP, U 0.022-25
C323 87-010-498-040 CAP,E 10-16 GAS
C324 87-010-498-040 CAP,E 10-16 GAS
C325 87-010-498-040 CAP,E 10-16 GAS
C326 87-010-498-040 CAP,E 10-16 GAS
C341 87-010-491-040 CAP,E 0.22-50 GAS
C342 87-010-491-040 CAP,E 0.22-50 GAS
C401 87-010-494-040 CAP,E 1-50 GAS
C402 87-A10-369-080 C-CAP,S 0.47-16 K B
C403 87-A10-369-080 C-CAP,S 0.47-16 K B
C405 87-010-759-080 C-CAP,U, 0.1-25F
C406 87-010-759-080 C-CAP,U, 0.1-25F
C407 87-010-494-040 CAP,E 1-50 GAS
C408 87-010-494-040 CAP,E 1-50 GAS
C409 87-010-494-040 CAP,E 1-50 GAS
C410 87-010-494-040 CAP,E 1-50 GAS
C423 87-010-497-040 CAP,E 4.7-35 GAS
C424 87-010-497-040 CAP,E 4.7-35 GAS
C425 87-010-497-040 CAP,E 4.7-35 GAS
C426 87-010-497-040 CAP,E 4.7-35 GAS
C427 87-012-270-080 C-CAP,U 470P-50
C428 87-012-270-080 C-CAP,U 470P-50
C429 87-012-270-080 C-CAP,U 470P-50
C430 87-012-270-080 C-CAP,U 470P-50
C451 87-012-358-080 C-CAP,S 0.47-10 F Z
C452 87-012-358-080 C-CAP,S 0.47-10 F Z
C453 87-010-831-080 C-CAP,U 0.1-16 F Z
C454 87-012-286-080 C-CAP,U 0.01-25
C461 87-010-787-080 C-CAP,U 0.022-25
C501 87-012-358-080 C-CAP,S 0.47-10 F Z
C502 87-012-358-080 C-CAP,S 0.47-10 F Z
C503 87-012-358-080 C-CAP,S 0.47-10 F Z
C504 87-012-358-080 C-CAP,S 0.47-10 F Z
C505 87-012-270-080 C-CAP,U 470P-50
C506 87-012-270-080 C-CAP,U 470P-50
C507 87-012-270-080 C-CAP,U 470P-50
C508 87-012-270-080 C-CAP,U 470P-50
C510 87-010-498-040 CAP,E 10-16 GAS
C515 8A-KC7-623-000 CAP,E 2200-16 125 BT
C516 87-012-368-080 C-CAP,S 0.1-50 F
C517 87-012-368-080 C-CAP,S 0.1-50 F
C519 87-010-494-040 CAP,E 1-50 GAS
– 4 –
Page 5
PART NO. DESCRIPTIONREF. NO. KANRI
C522 87-012-368-080 C-CAP,S 0.1-50 F
C701 87-012-278-080 C-CAP,U 2200P-50 B
C704 87-012-368-080 C-CAP,S 0.1-50 F
C705 87-012-278-080 C-CAP,U 2200P-50 B
C706 87-010-553-040 CAP,E 47-16 GAS
C707 87-010-787-080 C-CAP,U 0.022-25
C708 87-010-553-040 CAP,E 47-16 GAS
C709 87-010-759-080 C-CAP,U, 0.1-25F
C713 87-010-759-080 C-CAP,U, 0.1-25F
C714 87-010-787-080 C-CAP,U 0.022-25
C715 87-010-759-080 C-CAP,U, 0.1-25F
C716 87-010-759-080 C-CAP,U, 0.1-25F
C717 87-010-759-080 C-CAP,U, 0.1-25F
C718 87-010-759-080 C-CAP,U, 0.1-25F
C719 87-010-759-080 C-CAP,U, 0.1-25F
C720 87-010-787-080 C-CAP,U 0.022-25
C723 87-010-759-080 C-CAP,U, 0.1-25F
C725 87-010-553-040 CAP,E 47-16 GAS
C751 87-012-368-080 C-CAP,S 0.1-50 F
C752 87-012-368-080 C-CAP,S 0.1-50 F
C753 87-012-368-080 C-CAP,S 0.1-50 F
C754 87-010-553-040 CAP,E 47-16 GAS
C901 87-016-039-090 CAP,DL 0.022F-5.5 Z 70 FM
C902 87-012-358-080 C-CAP,S 0.47-10 F Z
C903 87-010-831-080 C-CAP,U,0.1-16F
C904 87-010-787-080 C-CAP,U 0.022-25
C905 87-012-180-080 C-CAP,U 22P-50 CH
C906 87-012-182-080 C-CAP,U 27P-50 CH
C907 87-010-831-080 C-CAP,U,0.1-16F
C908 87-012-282-080 CHIP CAP,U 4700P-50B
C909 87-012-274-080 CHIP CAP,U 1000P-50B
C910 87-012-195-080 C-CAP,U 100P-50CH
C911 87-012-195-080 C-CAP,U 100P-50CH
C912 87-010-787-080 C-CAP,U 0.022-25
C913 87-010-787-080 C-CAP,U 0.022-25
C914 87-010-831-080 C-CAP,U 0.1-16 Z F
C915 87-012-274-080 C-CAP,U 1000P-50 K B
C916 87-010-787-080 C-CAP,U 0.022-25
CON401 87-A61-219-010 CONN,20P H 52089-2020
CON402 87-A61-584-010 CONN,24P H 52089-2420
CON403 87-A61-583-010 CONN,16P H 52089-1620
CON701 8Z-KT1-611-010 CONN,16P CAM-B51
CON751 87-A60-670-010 CONN,6P H 2MM JMT
!
F701 8Z-KC1-621-010 FUSE,15A 32V
FFC401 88-KC4-641-010 FF-CABLE, 20P 1.0 90MM
J401 87-A61-224-110 JACK,PIN 4P XR-401
J402 8A-KC7-620-010 JACK,DIN 13 P SKDS1302
L101 87-003-143-080 COIL 4.7UH K LAL02
L102 8Z-KT1-619-010 COIL,68MH K7-D
L401 87-003-102-080 COIL,10UH J LAL02
L402 87-003-102-080 COIL,10UH J LAL02
L403 87-003-102-080 COIL,10UH J LAL02
L701 8B-KCF-615-010 FLTR,AMORPHOUS -CHOKE
L702 87-003-149-080 COIL,47UH J LAL02
L703 87-003-102-080 COIL,10UH J LAL02
SW903 87-A91-152-010 SW,SL 1-1-2 SSSS212-11-A
TU101 8B-KCF-621-010 TU UNIT, FAE347-A22
X901 87-A70-175-010 VIB,XTAL 4.5MHZ AT-49
NO.
DESCRIPTIONREF. NO. KANRI
PART NO.
NO.
C611 87-010-831-080 C-CAP,U,0.1-16F
C612 87-010-831-080 C-CAP,U,0.1-16F
C613 87-012-286-080 C-CAP,U 0.01-25
C615 87-A10-504-080 C-CAP,U 0.047-16 K B
CON601 87-A61-585-080 C-CONN,24P H 54548-2490
LCD701 8B-KC7-626-010 LCD,BKC-1/7
LED601 87-A91-355-040 C-LED,BR1112H-TR-RED
LED602 87-A91-355-040 C-LED,BR1112H-TR-RED
LED603 87-A91-355-040 C-LED,BR1112H-TR-RED
LED604 87-A91-355-040 C-LED,BR1112H-TR-RED
SW601 87-A90-001-080 C-SW,TACT SKQMAL
SW602 87-A90-001-080 C-SW,TACT SKQMAL
SW603 87-A90-001-080 C-SW,TACT SKQMAL
SW604 87-A90-001-080 C-SW,TACT SKQMAL
SW605 87-A90-001-080 C-SW,TACT SKQMAL
SW620 87-A90-001-080 C-SW,TACT SKQMAL
KEY C.B
C621 87-010-831-080 C-CAP,U,0.1-16F
CON603 87-A61-586-080 C-CONN,16P V FLZT-SM1
L601 87-005-906-080 C-COIL,S 10UH K LK2125
L602 87-005-906-080 C-COIL,S 10UH K LK2125
L603 87-005-906-080 C-COIL,S 10UH K LK2125
LED611 87-A91-355-040 C-LED,BR1112H-TR-RED
LED612 87-A91-355-040 C-LED,BR1112H-TR-RED
LED613 87-A91-355-040 C-LED,BR1112H-TR-RED
LED614 87-A91-355-040 C-LED,BR1112H-TR-RED
LED615 87-A91-355-040 C-LED,BR1112H-TR-RED
LED616 87-A91-355-040 C-LED,BR1112H-TR-RED
LED617 87-A91-355-040 C-LED,BR1112H-TR-RED
LED618 87-A41-096-010 LED,S1L31-3B0A2 BLU
LED619 87-A40-813-240 C-LED,SEC1E01C BLU
LED620 87-A40-813-240 C-LED,SEC1E01C BLU
LED621 87-A40-813-240 C-LED,SEC1E01C BLU
LED622 87-A40-813-240 C-LED,SEC1E01C BLU
LED625 87-A91-355-040 C-LED,BR1112H-TR-RED
LED626 87-A91-355-040 C-LED,BR1112H-TR-RED
SW606 87-036-220-080 C-SW,TACT SKQDAA
SW607 87-036-220-080 C-SW,TACT SKQDAA
SW608 87-036-220-080 C-SW,TACT SKQDAA
SW609 87-036-220-080 C-SW,TACT SKQDAA
SW610 87-036-220-080 C-SW,TACT SKQDAA
SW611 87-036-220-080 C-SW,TACT SKQDAA
SW612 87-036-220-080 C-SW,TACT SKQDAA
SW613 87-036-220-080 C-SW,TACT SKQDAA
SW614 87-036-220-080 C-SW,TACT SKQDAA
SW615 87-036-220-080 C-SW,TACT SKQDAA
SW616 87-036-220-080 C-SW,TACT SKQDAA
SW617 87-036-220-080 C-SW,TACT SKQDAA
SW618 87-036-220-080 C-SW,TACT SKQDAA
SENS C.B
CNA751 8B-KC7-617-010 CONN ASSY,6P EMP
FFC671 8B-KC7-618-010 F-CABLE,2P MOT
PS671 87-A92-061-080 C-SNSR,GP1S092 HCPI
SW671 87-A92-039-080 C-SW,PUSH ESE22MH24XQ
DISP C.B
C602 87-010-831-080 C-CAP,U,0.1-16F
C603 87-010-831-080 C-CAP,U,0.1-16F
C604 87-A10-504-080 C-CAP,U 0.047-16 K B
C605 87-012-199-080 C-CAP,U 220P-50
C606 87-A10-504-080 C-CAP,U 0.047-16 K B
C607 87-A10-504-080 C-CAP,U 0.047-16 K B
C608 87-A10-504-080 C-CAP,U 0.047-16 K B
C609 87-A10-504-080 C-CAP,U 0.047-16 K B
C610 87-010-805-080 C-CAP,S 1-16
AUX C.B
FFC601 8B-KC1-602-010 F-CABLE,4P (AUX-W/S)
J601 87-A60-925-010 JACK,3.6 BLK ST W/SW
LED L C.B
LED605 87-A41-085-010 LED,NSPW315BS WHT
LED R C.B
– 5 –
Page 6
PART NO. DESCRIPTIONREF. NO. KANRI
NO.
LED606 87-A41-085-010 LED,NSPW315BS WHT
LED C.B
FFC651 8B-KC1-603-010 F-CABLE,2P (PWB LED)
LED651 87-A40-228-040 LED,SLR-342MG T31 GREEN
FLEX KEY C.B
8B-KC7-612-010 PWB,FLEX KEY
FLEX DISP C.B
8B-KC7-611-010 PWB,FLEX DISP
CD C.B
C0601 87-A10-263-080 C-CAP,U 0.1-16 Z F
C0602 87-A10-263-080 C-CAP,U 0.1-16 Z F
C0603 87-A10-263-080 C-CAP,U 0.1-16 Z F
C0604 87-A10-263-080 C-CAP,U 0.1-16 Z F
C0605 87-012-274-080 C-CAP,U 1000P-50 K B
C0606 87-012-274-080 C-CAP,U 1000P-50 K B
C0621 87-010-880-080 C-CAP,E 47-6.3 M MF
C0622 87-A10-263-080 C-CAP,U 0.1-16 Z F
C0623 87-A10-263-080 C-CAP,U 0.1-16 Z F
C0624 87-A10-263-080 C-CAP,U 0.1-16 Z F
C0625 87-A10-263-080 C-CAP,U 0.1-16 Z F
C0626 87-A10-263-080 C-CAP,U 0.1-16 Z F
C0627 87-A10-263-080 C-CAP,U 0.1-16 Z F
C0628 87-A10-263-080 C-CAP,U 0.1-16 Z F
C0629 87-A10-263-080 C-CAP,U 0.1-16 Z F
C0630 87-A10-263-080 C-CAP,U 0.1-16 Z F
C0631 87-010-880-080 C-CAP,E 47-6.3 M MF
C0651 87-016-287-080 C-CAP,TN 3.3-6.3 M
C0652 87-012-286-080 C-CAP,U 0.01-25 K B
C0653 87-010-880-080 C-CAP,E 47-6.3 M MF
C0654 87-A10-263-080 C-CAP,U 0.1-16 Z F
C0655 87-A10-263-080 C-CAP,U 0.1-16 Z F
C0656 87-012-178-080 C-CAP,U 18P-50 J CH
C0657 87-012-178-080 C-CAP,U 18P-50 J CH
C0658 87-A10-263-080 C-CAP,U 0.1-16 Z F
C0659 87-016-317-080 C-CAP,TN 2.2-6.3 M
C0660 87-A10-263-080 C-CAP,U 0.1-16 Z F
C0661 87-010-880-080 C-CAP,E 47-6.3 M MF
C0662 87-A10-263-080 C-CAP,U 0.1-16 Z F
C0663 87-012-271-080 C-CAP,U 560P-50 K B
C0664 87-012-271-080 C-CAP,U 560P-50 K B
C0665 87-012-193-080 C-CAP,U 82P-50 J CH
C0666 87-012-193-080 C-CAP,U 82P-50 J CH
C0667 87-012-335-080 C-CAP,U 270P-50 J SL
C0668 87-012-335-080 C-CAP,U 270P-50 J SL
C0669 87-012-274-080 C-CAP,U 1000P-50 K B
C0670 87-012-274-080 C-CAP,U 1000P-50 K B
C0803 87-A10-711-080 C-CAP,E 100-6.3 M MF
C0804 87-012-274-080 C-CAP,U 1000P-50 K B
C0805 87-A10-260-080 C-CAP,U 0.1-16 K B
C0806 87-012-280-080 C-CAP,U 3300P-50 K B
C0808 87-A10-263-080 C-CAP,U 0.1-16 Z F
C0809 87-010-880-080 C-CAP,E 47-6.3 M MF
C0811 87-A10-263-080 C-CAP,U 0.1-16 Z F
C0812 87-012-165-080 C-CAP,U 3P-50 C CH
C0813 87-A10-263-080 C-CAP,U 0.1-16 Z F
C0815 87-A10-263-080 C-CAP,U 0.1-16 Z F
C0816 87-010-880-080 C-CAP,E 47-6.3 M MF
C0817 87-010-880-080 C-CAP,E 47-6.3 M MF
C0831 87-012-199-080 C-CAP,U 220P-50 J CH
DESCRIPTIONREF. NO. KANRI
PART NO.
NO.
C0832 87-A10-504-080 C-CAP,U 0.047-16 K B
C0833 87-012-198-080 C-CAP,U 180P-50 J CH
C0834 87-012-199-080 C-CAP,U 220P-50 J CH
C0835 87-016-669-080 C-CAP,S 0.1-25 K B
C0836 87-012-199-080 C-CAP,U 220P-50 J CH
C0837 87-012-280-080 C-CAP,U 3300P-50 K B
C0838 87-A10-504-080 C-CAP,U 0.047-16 K B
C0839 87-010-880-080 C-CAP,E 47-6.3 M MF
C0840 87-A10-263-080 C-CAP,U 0.1-16 Z F
C0841 87-A10-263-080 C-CAP,U 0.1-16 Z F
C0842 87-016-526-080 C-CAP,S 0.47-16 BK
C0843 87-012-198-080 C-CAP,U 180P-50 J CH
C0844 87-012-198-080 C-CAP,U 180P-50 J CH
C0845 87-012-273-080 C-CAP,U 820P-50 K B
C0846 87-012-273-080 C-CAP,U 820P-50 K B
C0847 87-016-563-080 C-CAP,TN 10-10
C0848 87-016-563-080 C-CAP,TN 10-10
C0861 87-A10-263-080 C-CAP,U 0.1-16 Z F
C0871 87-A10-419-080 C-CAP,TN 1-16 A TCF
C0872 87-A10-419-080 C-CAP,TN 1-16 A TCF
C0873 87-016-526-080 C-CAP,S 0.47-16 BK
C0874 87-A10-263-080 C-CAP,U 0.1-16 Z F
C0875 87-A10-260-080 C-CAP,U 0.1-16 K B
C0876 87-A10-260-080 C-CAP,U 0.1-16 K B
C0877 87-010-880-080 C-CAP,E 47-6.3 M MF
C0878 87-A10-263-080 C-CAP,U 0.1-16 Z F
C0879 87-012-274-080 C-CAP,U 1000P-50 K B
C0880 87-010-880-080 C-CAP,E 47-6.3 M MF
C0881 87-A12-424-080 C-CAP,E 220-10 M 4B SE1A221
C0882 87-A10-263-080 C-CAP,U 0.1-16 Z F
C0883 87-A10-263-080 C-CAP,U 0.1-16 Z F
C0884 87-012-274-080 C-CAP,U 1000P-50 K B
C0885 87-A10-473-080 C-CAP,E 47-10 MF10FC(M)
C0886 87-A10-263-080 C-CAP,U 0.1-16 Z F
C0887 87-A10-263-080 C-CAP,U 0.1-16 Z F
C0888 87-A10-263-080 C-CAP,U 0.1-16 Z F
C0898 87-012-274-080 C-CAP,U 1000P-50 K B
C0899 87-A10-711-080 C-CAP,E 100-6.3 M MF
CN0801 87-A61-125-080 C-CONN,16P H FLZ-SM1-TB
CN0891 87-A61-220-080 C-CONN,20P H 52271-2090
L0621 87-A50-536-080 C-COIL,10UH K LQH3C24
L0622 87-A50-536-080 C-COIL,10UH K LQH3C24
L0651 87-A50-499-080 C-COIL,S 4.7UH K LQG21N
L0652 87-A50-536-080 C-COIL,10UH K LQH3C24
L0801 87-A50-536-080 C-COIL,10UH K LQH3C24
L0802 87-A50-536-080 C-COIL,10UH K LQH3C24
L0831 87-A50-536-080 C-COIL,10UH K LQH3C24
L0832 87-A50-536-080 C-COIL,10UH K LQH3C24
L0833 87-A50-536-080 C-COIL,10UH K LQH3C24
L0871 87-A50-367-080 C-COIL, 10UH LQG21F
L0881 87-A50-536-080 C-COIL,10UH K LQH3C24
S0861 87-A91-627-080 SW,PUSH MPU10372MLBO
X0601 87-A70-266-080 C-VIB,CER 6.25MHZ CSTRC-MG05
X0651 87-A70-267-080 C-VIB,XTAL 14.725MHZ CX-53F
X0831 87-A70-261-080 C-VIB,CER 16.93MHZ CSTCW-MX03T
SENSOR C.B
SW1 87-A91-627-080 SWITCH
SW2 87-A91-627-080 SWITCH
– 6 –
Page 7
CHIP RESISTOR PART CODE
Chip Resistor Part Coding
88
A
Resistor Code
Chip resistor
Wattage Type Tolerance
1/16W 1005 5% CJ
1/16W
1/10W
1/8W
1608
2125
3216
5%
5%
5%
TRANSISTOR ILLUSTRATION
Symbol
CJ
CJ
CJ
Figure
Value of resistor
Form
L
Dimensions (mm)
t
W
0.55
Resistor Code
108
118
128
LW t
1.0 0.5 0.35 104
1.6 0.8 0.45
2 1.25 0.45
3.2
1.6
: A
: A
C
B C E B C E
KTA1658(Y)
KTC4369(Y)
2SD2395E
E C B
2SD1858 TV2
B
2SA1037AK(R)
2SB1197KQ
2SC2412KR
DTA144EKA
DTA114YKA
E
DTB113ZK
DTC114TKA
DTC114YKA
DTC124EKA
DTC143TKA
– 7 –
Page 8
BLOCK DIAGRAM (CD / SENSOR)
12CC
12CB
33
41 34
43
44
45
48
IC622
2
3
4
5
8
9
08 DCK
SN74AHC1G
32
CS
HD4
O
I
I
5
VDD
31
WR
HD4
50
HD5
PR
VSENS
13
1416171819
4
1
LRCK
30
29
RD
RS
IC623
HD5
HD6
HD6
HD7
IO7
OE
22
ROE
RCS
42
43
CLKI
AVDD
IC621
MAS3507D-G10
PI19
PI18
PI17
HD5
HD6
HD7
2
BCK
PCMD
C2PO
27
28
BCK
LRCK
SDATA
LC89513K
DTEN
HD7
HRD
535251
55
54
IO2
IO3
191513
IO7
IO3
A11
A10
CS
21
20
23
RA9
RAB
RAA
MP3 DECODER
PI16
PI15
PI14
202122
HD3
HD2
HD4
XTAL
23
242526
VDD
C2PQ
XTALCK
ROM DECODER
VDD
IO0
56
57
IO0
IO0
11
IO2
IO0
A13
A9
A8
26
24
25
RA8
RAE
RAD
SII
SOI
PI12
PI13
HD1
22
RESET
IO7
64
IO7
T15L256A-70P
A12
A14
RA7
RAC
C
I2C
I2CD
1816151413
12
XT0
XT1
SCL
SDA
VDD
CLKOUT
I
2324
I
SQSO
SCK
SQ IN
SCLK
SCLK
DCDMS
DMSCD
41
36
40
42
REF1
SYS-DI
SYS-DO
AV
SYS-CLK
IC601
UPD784216AYGC-110-8EU
SQCK
SENS
SV-CONT
SENS
XRST
SQCK
SV-CONT
I
2526
O
3132
FINL
39
A0
20
A0
IO1
A10
IO2
212223
31
A10
D0D1D2
MICON
XRST
APC
CD-MUTE
GFS
RF-SW
DFS
SYSN
RF-SW
APC
C2PO
IC651
DAC3550A-C2
A7
A12
A14
111213
A7
A12
A14
IO3
IO4
25
D3
C2PO
LOCK
FOK
99
100
FOK
LOCK
DAC-C2
FINR
43
A16
D7
VREF
44
A15
10
A16
IO8
29
10
9
A13A8A9
234
7
A8
A9
A13
A15
UT62L1024LC-70LL
OE
VCC
CE1
8
30
32
25
24
23
LO
LO
2122
17 19 20
16
15
14
10 11
8 9
CHACK SW
5 6
2 3
1
XTAL-VDD
A11
5
1
A11
WE
2
CE
6
LOLO
CHACK SW
BA033FP
IC871
VDD SW
VOUT
2
GND
1 3
VIN
2
ON
3
IC872
VOUT
1
VIN
PQ20WZ1U
1
05
Q806
Q86
Q862
Q807
Q8
Q804
VDD SW
VDD SW
XTAL-VDD
D861
8
SRQ
HEX BUFFER
IC873
SN74LVC07A
1 2 3 4 5 6
DCDMS
1A 1Y 2A 2Y 3A 3Y
14 13 12 11 10 9
VCC6A6Y5A5Y4A4Y
C2PO
1
2
3456789101819
20
++
70
AOUT2
AIN2
TFDR
FFDR
TRDR
31
3233383940
30
757677
LOUT2
IC831
FRDR
71
72
AIN1
AOUT1
LOUT1
CD DSP
CXD2587Q
VC
FE
69
AVDD1
SE
78
AVDD2
FOK
LOCK
24
25
LOCK
FOK
31
2826
25
24
23
HD0
SOI
SOI
CD C.B 2/2
(MP3 SECTION)
I2CD
I2C C
35
45
47
I2CD
I2CC
48
DEC RST
20 21
1918
108 16
2
28
VCC
A7
A0
WE
321
27
10
RA0
RWE
64 63 56 55
71
75 74 73
DTEN
MP3RST
XLAT
RD
XCLK
VDD
WR
CLOK
XDATA
XLAT
DATA
77787981828384858687888990919395969798
19
17
20
16
18
SRQ
CS
SCK
DCDMS
SLEEP
DMSCD
XTAL
BCK
LRCK
PCMD
616263
67
65
66
BCK
XTAI
PCMD
XTAO
XVDD
LRCK
59
57
42 43 51
41
MDP
SFDR
SRDR
28
29
26
TO MAIN C.B CON401 (FFC401)
3
24579
6
8
12
10
11
14
15
13
S-GND
S-GND
D-GND
RESET
8V (ACC)
5V (BAT)
5V (ACC)
S-GND
1
CN891
LCH
RCH
A-GND
A-GND
INSW
1
4 2
5
O
VC
RF DCI
RF DC
DC-OFST
PD
A
BCD
LD
EQ-IN
Q801
Q802
LD CONT
APC
D
B
A
PDVRVC
GND
LD
C
CN801
CDC-02AW1
VCC
CEI
CXA2581N(RF)
IC801
SW
AC-SUM
RF-SW
VCC
CE
TE-BAL
F
E
FEFCS+
TE
DVCC
FEI
DVC
TRK-
FOCUS COIL
FE
RF AC
TRK+
TRACKING COIL
CHACK SW
CD C.B 1/2
(CD SECTION)
LINT SW
8/12 SW
TCS-
LOADSW
GND
SP-
8/12 5V
(RED)
(BLACK)
SW2
L
SP+
LOADSW
(BROWN)
(BLACK)
(RED)
M
SW1
M3
GND
SL-
SL+
(YELLOW)
(ORANGE)
M
M1
SPINDL E M OTOR
LD+
(GREEN)
LD-
LIMT SW
(BROWN)
(RED)
(WH ITE )
SW5
M
M2
SLED MOTOR
LOADING MOTOR
-FWD
SV-CONT
LO-REV
LO
FIN
RIN
OUT2
OUT1
9
101213
VREF
VCC
VM
LOADING DRIVER
IC881
22 23 24 26 27
BA6392FP
SV-DRV
21
2019
17
1615
8
Page 9
WIRING – 1 (MAIN / SENS / LED / FLEX KEY 2 / 2 / FLEX DISP 2 / 2) <1 / 2>
32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
– 9 –
R
S
T
U
Page 10
WIRING – 1 (MAIN / LED) <2 / 2>
1 2 3 4 5 6 7 8 9 1011121314151617181920212223242526272829303132
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
S
T
U
– 10 –
Page 11
SCHEMATIC DIAGRAM 1 (MAIN / SENS / LED)
11
Page 12
WIRING 2 (DISP / KEY / AUX / LED L / LED R / FLEX KEY 1 / 2 / FLEX DISP 1 / 2) <1 / 2>
32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
12
R
S
T
U
Page 13
WIRING 2 (DISP / KEY / AUX) <2 / 2>
1 2 3 4 5 6 7 8 9 10 11121314151617181920212223242526272829303132
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
S
T
U
13
Page 14
SCHEMATIC DIAGRAM 2 (DISP / KEY / AUX / LED L / LED R)
14
Page 15
WIRING 5 (CD / SENSOR)
16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
(A.G)
X651
A
A
B
B
C
C
D
D
E
E
F
F
G
G
H
H
C834
C835
I
I
J
J
K
K
L
L
M
M
N
N
O
O
P
P
Q
Q
R
R
S
S
T
T
U
U
15
Page 16
SCHEMATIC DIAGRAM 3 (CD:1 / 2 / SENSOR)
K
L
16
Page 17
SCHEMATIC DIAGRAM 3 (CD:2 / 2)
K
17
Page 18
LCD DISPLAY (LCD, BKC1/7)
SEGMENT WIRING
COMMON WIRING
18
Page 19
IC BLOCK DIAGRAM
19
Page 20
20
Page 21
IC,DAC3550A-C2
SAMPLE RATE
DETECTION
PLL
CLKOUT
14
XTO
13
OSC
12
XTI
AUX2L
29
AUX1L
31
2424
23
24 25
24
DAI
I S
WSI
2
CLI
INTERPOLATION FILTER
VARIABLE S & H
3rd-ORDER NOISE SHAPER
&
MULTIBIT DAC
ANALOG LOW-PASS FILTER
INPUT SELECT
SWITCH MATRIX
DIGITAL
SUPPLY
ANALOG
SUPPLY
2
I C
CONTROL
VDD
VSS
AVDD0
AVDD1
AVSS0
AVSS1
VREF
AGNDC
SDA
SCL
TESTEN
PORQ
DEECTRL
MCS1
MCS2
AUX1R
AUX2R
18
17
9
10
3
2
44
1
16
15
27
26
21
19
20
32
30
DEEML
34
FOPL
38
FOUTL
37
FINL
39
IC,BA6417F
POSTFILTER OP AMPS
DEEMPHASIS OP AMPS
LINE-OUT
ANALOG VOLUME
HEADPHONE AMPLIFIER
5
17
OUTROUTL
7
DEEMR
FOPR
FOUTR
FINR
35
42
41
43
– 21 –
Page 22
IC,PQ20WZ1U
IC,UT62L1024LC-70LL
A16
10
A15
7
A13
4
A14
11
A12
12
ROW
A7
DECODER
13
A6
14
A5
15
A4
16
A8
3
1024 ROWS X 1024 COLUMNS
MEMORY ARRAY
VCC
VSS
8
24
IC,SN74LVC07A
14
VCC
13
6A
1A
1Y
1
2
11
12
2A
3
4
IC,T15L256A-70P
VCC
28
VSS
14
A0
10
A1
9
A2
8
A3
7
A4
6
A5
5
A6
4
A7
3
DECODER CORE ARRAY
A8
25
A9
24
A10
21
A11
23
A12
2
A13
26
A14
1
I/O1
21
9
10
4A
5Y5A6Y
2Y
5
8
4Y
GND
3Y3A
7
6
I/O2
22
I/O3
23
I/O4
25
I/O
I/O5
CONTROL
26
I/O6
27
I/O7
28
I/O8
29
CE1
30
CE2
6
LOGIC
WE
CONTROL
5
OE
32
SYMBOL DESCRIPTION
A0 - A16 ADDRESS INPUTS
I/O1 - I/O8 DATA INPUTS/OUTPUTS
CE1,CE2 CHIP ENABLE 1,2 INPUTS
WE WRITE ENABLE INPUT
OE OUTPUT ENABLE INPUT
VCC POWER SUPPLY
VSS GROUND
NC NO CONNECTION
COLUMN I/O
COLUMN DECODER
A10
A11A9A3A2A1A0
31 1 2 17 18 19 20
I/O0
11
I/O1
12
I/O2
CS
20
OE
22
CONTROL
WE
27
SYMBOL DESCRIPTION
A0 - A14 ADDRESS INPUTS
I/O0 - I/O7 DATA INPUTS/OUTPUTS
CS CHIP SELECT INPUTS
WE WRITE ENABLE
OE OUTPUT ENABLE
VCC POWER SUPPLY
VSS GROUND
DATA I/O
I/O3
I/O4
I/O5
I/O6
I/O7
13
15
16
17
18
19
– 22 –
Page 23
IC DESCRIPTION
IC, µPD178018AGC-598
Pin No. Pin Name I/O Description
1 FM/AM S–M I Input RDS AF signal and FM/AM S-meter signal input.
2 LEVEL IND I Voltage input for level indicator.
3 SEN 1 I Load sens detect input.
4 CD CONNECT I Connection check of CD changer.
5 CD DISP SEL O Signal output of communication timing with CD changer. H: TX, L: RX.
6 CD CLO O Synchronize clock signal output for transmission.
7 CD DI I Data signal input for reception.
8 CD DO O Data signal output for transmission.
9 CD CLI I Synchronize clock signal input for reception.
10 LCD STB/CE O LCD driver CE signal output.
11 CLK SEL O Clock selection for LCD driver.
12 LCD DI I Data signal input for LCD driver.
13 LCD DO O Data signal output for LCD driver.
14 LCD CLO O Synchronize clock signal output for LCD driver.
15 CD ACC CONT O ACC signal output for CD changer.
16 POWER MUTE O POWER MUTE signal output.
17 ST-BY MUTE O ST-BY MUTE signal output.
18 POWER CONT O POWER CONTROL signal output.
19 CONT 1 O LCD contrast: Control 1. (Not used)
20 CONT 2 O LCD contrast: Control 2. (Not used)
21 GND PORT _ Ground for port.
22 VDD PORT – Power supply for port.
23 MUTE O Audio mute output.
24 BAND CONT O FM/AM power switch output. H: AM, L: FM.
25 RADIO CONT O Radio power switch output. L: Radio mode. (Not used)
26 RDS MODE O Hi output during RDS AF mode. (Not used)
27 IF REQ O Request output for IF count signal.
28 AM IF I AM IF count signal input.
29 FM IF I FM IF count signal input.
30 VDD PLL – Power supply for PLL.
31 FM OSC I Input from FM station.
32 AM OSC I Input from AM station.
33 GND PLL – Ground for PLL.
34 EO0 O Error output from charge pump. (Not used)
35 EO1 O Error output from charge pump.
36 GND – Ground.
37 LOC/DX O LOC/DX switch output during radio seek. H: LOC, L: DX.
38 SD/ST IND I
39 PHONE MUTE I External mute control. L: -20dB Mute.
40 CDS CS O CS signal output.
41 CDS RESET O RESET signal output.
Station detect signal input during FM/AM seek. H: Detect station / L: Seeking.
Stereo signal input during FM reception. H: Mono, L: ST.
– 23 –
Page 24
Pin No. Pin Name I/O Description
42 CDS SLEEP O SLEEP signal output.
43 CDS STOP I STOP signal input.
44 CDS IN I DISC insertion detect input.
45 SEN2 I Load sens detect input.
46 BBE-2 I BBE input 1. (Not used)
47 BBE-1 I BBE input 2. (Not used)
48 MF.CON O SLEEP signal control output.
49 MI–1 I Diode matrix input for default setting.
50 MI–2 I Diode matrix input for default setting.
51 MI–3 I Diode matrix input for default setting.
52 MO–1 O Diode matrix output for default setting.
53 MO–2 O Diode matrix output for default setting.
54 MO–3 O Diode matrix output for default setting.
55 MO–4 O Diode matrix output for default setting.
56 PANCON1 O Panel control motor reverse drive output.
57 PANCON2 O Panel control motor forward drive output.
58 ACC IN I ON/OFF input for ACC (accessory power supply).
59 BEEP O BEEP output.
60 REMOTE I Remote control input.
61 E–VOL CE O CE output to electrical volume.
62 E–VOL DO O Data output to electrical volume.
63 E–VOL CLO O Clock output to electrical volume.
64 DRV CONT O Hi output during DRIVE mode.
65 RDS DI I RDS data input. (Connected to GND through a resistor)
66 DFP IN I Front panel detection.
67 FLAP IN I OPEN/CLOSE detection of FLAP DFP. DFP IN: Enable when High.
68 RDS CLI I RDS clock input. (Connected to GND through a resistor)
69 JACK IN I JACK detect input.
70 BATT IN I ON/OFF input for BATT.
71 RE-1 I Rotary encoder input 1. (Connected to GND through a resistor)
72 RE-2 I Rotary encoder input 2. (Connected to GND through a resistor)
73 S-REQ – S-REQ signal input for CDS.
74 REG CPU – CPU power-supply regulator.
75 GND – Ground.
76 X–OUT – System clock oscillator.
77 X–IN – System clock oscillator.
78 REG OSC – Oscillator circuit regulator.
79 VDD – System power supply.
80 RESET I System reset.
– 24 –
Page 25
IC, LC75374E
Pin No. Pin Name I/O Description
1 RVR IN I 4dB volume control input. Must be driven at a low impedance.
2 R COM – 1dB volume control common pin. (Connected to GND through a capacitor)
For the connection of capacitors that compensate for bass and treble in the tone control circuits.
3 ~ 5 RT1 ~ RT3 – A high-frequency compensation capacitor must be connected between RT1 and RT2.
A low-frequency compensation capacitor must be connected between RT2 and RT3.
6 RT OUT O Tone control output.
7 RS IN I Super bass input. Must be driven at a low impedance.
8 NC – Connected to GND.
9 NC – Not connected.
10 RS3
11 RS OUT
12 FR IN I Fader input. Must be driven at a low impedance.
13 FR OUT
14 RR OUT
15 VSS – GND.
16 CL
17 DI
18 CE –
19 VREF –
20 RL OUT
21 FL OUT
22 FL IN I Fader input. Must be driven at a low impedance.
23 LS OUT
24 LS3
25 NC – Not connected.
O For the connection of RCH super bass compensation capacitors.
O Fader output. The front and rear sides can be attenuated independently.
I Serial data and clock input for control.
Chip enable. Data is written in the internal latch when the chip enable signal goes "L"
from "H", and each analog switch is activated. Data transfer is enabled at "H".
Generates a 1/2VDD power source. A capacitor must be connected between VREF and
GND as a troubleshooting against power ripples.
O Fader output. The front and rear sides can be attenuated independently.
O For the connection of LCH super bass compensation capacitors.
26 NC – Connected to GND.
27 LS IN I Super bass input. Must be driven at a low impedance.
28 LT OUT O Tone control output.
For the connection of capacitors that compensate for bass and treble in the tone control circuit.
29 ~ 31 LT3 ~ LT1 A high-frequency compensation capacitor must be connected between LT1 and LT2.
A low-frequency compensation capacitor must be connected between LT2 and LT3.
32 L COM – 1dB volume control common pin.
33 LVR IN I 4dB volume control input. Must be driven at a low impedance.
34 LSELO O Input selector output pin.
35 AUX (L)
36 CD (L)
37 TUN (L)
38 TP (L)
39 VDD – Power supply.
I Signal input pins.
– 25 –
Page 26
Pin No. Pin Name I/O Description
40 TP (R)
41 TUN (R)
42 CD (R)
43 AUX (R)
44 RSELO O Input selector output pin.
I Signal input pins.
IC, LC75817W-8720
Pin No. Pin Name I/O Description
1 ~ 56 S1 ~ S56 O LCD segment output.
57 ~ 59 S57 ~ S59 O LCD segment output. (Not used)
60 S60 / COM10 O LCD segment output / LCD common driver output. (Not used)
61 COM9 O LCD common driver output. (Not used)
62 ~ 69 COM8 ~ COM1 O LCD common driver output.
70 , 71 KS1, KS2 O Key scan output. (Not used)
72 ~ 75 KS3 ~ KS6 O Key scan output.
76 ~ 80 KI1 ~ KI5 I Key scan input.
81 P-1
82 P-2
83, 84 P-3, P-4 O Not used.
85 VDD – Power supply.
86 VLCD – LCD power supply.
87 VLCD0 – LCD power supply.
88 VLCD1 I
89 VLCD2 I 1/2 bias voltage is applied to the LCD drive externally.
90 VLCD3 I
91 VLCD4 – Connected to GND.
92 VSS – GND.
93 TEST – Test pin. (Connected to GND)
94 OSC-OUT O
95 OSC-IN I
96 INT – Connected to VDD.
97 DO O Serial data interface pin; output data.
98 CE O Serial data interface pin; chip enable.
99 CL O Serial data interface pin; synchronization.
O Illumination driver output.
3/4 bias voltage is applied to the LCD drive externally.
1/4 bias voltage is applied to the LCD drive externally.
Resistor and capacitor are attached externally to form an oscillator circuit.
100 DI I Serial data interface pin; data transferred.
– 26 –
Page 27
IC, CXD2587Q
Pin No. Pin Name I/O Description
1
SQSO
O
Sub-Q 80-bit and PCM peak level data output. CD TEXT data output.
10
11
12
13
14
15
16
17
18
O
–
I/O
O
O
O
O
O
I
Clock input for reading SQSO.
I
System reset. Reset at "L".
I
Muting input. Muted at "H".
I
Serial data input from CPU.
I
Latch input from CPU. Latches serial data at the trailing edge.
I
Clock input for serial data transfer from CPU.
SENS output to CPU.
I
Clock input for reading SENS serial data.
Power supply of digital circuits.
Input/output for anti-shock. (Connected to GND)
I
Microprocessor extended interface (input A). (Connected to GND)
I
Microprocessor extended interface (input B). (Connected to GND)
Microprocessor extended interface (output). (Not used)
WFCK output. (Not used)
WUGF output. MNT1 or RFCK is output when switched by command. (Not used)
XPCK output. MNT0 is output when switched by command. (Not used)
GFS output. MNT3 or XROF is output when switched by command.
2
3
4
5
6
7
8
9
SQCK
XRST
SYSM
DATA
XLAT
CLOK
SENS
SCLK
VDD
ATSK
SPOA
SPOB
XLON
WFCK
XUGF
XPCK
GFS
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
C2PO
SCOR
COUT
MIRR
DFCT
FOK
LOCK
MDP
SSTP
SFDR
SRDR
TFDR
TRDR
FFDR
FRDR
VSS
O
O
I/O
I/O
I/O
I/O
I/O
O
O
O
O
O
O
O
–
C2PO output.
Outputs "H" when Sub-code sync S0 or S1 is detected.
Track number count signal input/output. (Not used)
Mirror signal input/output. (Not used)
Defect signal input/output. (Not used)
Focus OK signal input/output.
Outputs "H" when GFS sampled by 460 Hz is "H"; "L" when GFS is "L" continuously for 8
samplings. Or, a signal is input when LKIN is "1".
Spindle motor servo control output.
I
Disc innermost edge detection signal input. (Connected to GND)
Sled drive output.
Sled drive output.
Tracking drive output.
Tracking drive output.
Focus drive output.
Focus drive output.
Ground of digital circuits.
35
36
37
38
39
TEST
TES1
XTSL
VC
FE
I
TEST pin. Normally grounded. (Connected to GND)
I
TEST pin. Normally grounded. (Connected to GND)
Crystal select input. "L" when 16.9344MHz crystal is used; "H" when 33.8688MHz crystal is
I
used. (Connected to GND)
I
Neutral voltage input.
I
Focus error signal input.
– 27 –
Page 28
Pin No. Pin Name I/O Description
40
SE
I
Sled error signal input.
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
TE
CE
RFDC
ADIO
AVSS0
IGEN
AVDD0
ASYO
ASYI
BIAS
RFAC
AVSS3
CLTV
FILO
FILI
PCO
AVDD3
I
Tracking error signal input.
I
Neutral servo analog input.
I
RF signal input.
O
For test. Do not connect. (Not used)
–
Ground of analog circuits.
I
Constant current input for OP-AMP.
–
Power supply of analog circuits.
O
EFM full-swing output ("L": VSS; "H": VDD).
I
Asymmetry comparator voltage input.
I
Asymmetry circuit constant current input.
I
EFM signal input.
–
Ground of analog circuits.
I
VCO1 control voltage input for multiplication.
O
Filter output for master PLL (Slave: Digital PLL).
I
Filter input for master PLL.
O
Charge pump output for master PLL.
–
Power supply of analog circuits.
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
VSS
VDD
DOUT
LRCK
PCMD
BCK
EMPH
XVDD
XTAI
XTAO
XVSS
AVDD1
AOUT1
AIN1
LOUT1
AVSS1
–
Ground of digital circuits.
–
Power supply of digital circuits.
O
Digital output. (Not used)
O
D/A interface LR clock output f=Fs.
O
D/A interface serial data output (2's COMP, MSB first).
O
D/A interface bit clock output.
Outputs "H" when disc to be played is applied with emphasis; "L" when disc to be played is not
O
applied with emphasis. (Not used)
–
Power supply of master clock.
I
Crystal oscillator input. External master clock is input to this pin.
O
Crystal oscillator output.
–
Ground of master clock.
–
Power supply of analog circuits.
O
Lch analog output.
I
Lch OP-AMP input.
O
Lch line output.
–
Ground of analog circuits.
74
75
76
77
78
79
80
AVSS2
LOUT2
AIN2
AOUT2
AVDD2
RMUT
LMUT
–
Ground of analog circuits.
O
Rch line output.
I
Rch OP-AMP input.
O
Rch analog output.
–
Power supply of analog circuits.
O
Rch "0" detection flag. (Not used)
O
Lch "0" detection flag. (Not used)
– 28 –
Page 29
IC, CXA2581N
Pin No. Pin Name I/O Description
1
LD
O
APC-AMP output.
10
11
12
13
14
15
16
17
18
2
3
4
5
6
7
8
9
PD
EQ-IN
AC-SUM
GND
A
B
C
D
E
F
SW
DVCC
DVC
RFAC
FE
FEI
TE
I
APC-AMP input.
I
RFAC-system VCA/EQ block input.
O
RFAC-system RF SUM output.
–
Ground.
I
A-signal input.
I
B-signal input.
I
C-signal input.
I
D-signal input.
I
E-signal input.
I
F-signal input.
I
MODE switching signal input.
–
Power supply.
O
DVC output.
O
RFAC signal output.
O
Focus error signal output.
I
FE AMP virtual ground.
O
Tracking error signal output.
19
20
21
22
23
24
25
26
27
28
29
30
TE-BAL
CE
CEI
VCC
RFG
BST
VFC
RFC
VC
RFDCO
RFDCI
DC-OFST
I
TE balance adjustment. (Connected to VC)
O
Center error signal output.
I
CE AMP virtual ground.
–
Power supply.
I
RFAC-system VCA block low-frequency gain adjustment.
I
EQ boost level adjustment. (Connected to VC)
I
EQ cutoff frequency adjustment.
I
EQ cutoff frequency adjustment.
O
VC voltage output.
O
RFDC signal output.
I
RFDC AMP virtual ground.
I
RFDC signal output offset adjustment.
– 29 –
Page 30
IC, UPD784216AYGC-110-8EU
Pin No. Pin Name I/O Description
1
CD ON
CD mechanism power control output.
O
10
11
12
13
14
15
16
17
18
2
3
4
5
6
7
8
9
SRQ
SLEEP
NC
LIMT-SW
CHACK-SW
NC
8/12 SW
VDD
X2
X1
VSS
XT2
XT1
RESET
INT
HDRQ
NC
Mechanism microprocessor communication request.
O
Sleeping request from system microprocessor.
I
Not connected.
–
Inner edge limit switch.
I
Checking complete switch.
I
Not connected
–
8/12 cm check switch.
I
Power supply.
–
6.25MHz oscillator circuit.
–
6.25MHz oscillator circuit.
–
GND.
–
Not used.
–
Connected to GND.
–
System reset input. Active “L”.
I
Interruption input to IC, LC89513K pin 43. Active “L”.
I
Output gate to IC, SN74AHC1G08 DCK pin 2.
O
Not connected.
–
19
20
21
22
23
24
25
26-32
33
34
35
36
37
38
39
40
41
SCOR
CS
LO-REV
LO-FWD
AVDD
AVREF0
LOAD SW
NC
AVSS
MP3ON
DEC RST
AVREF1
DEBUG1 (SI2)
DEBUG2 (SO2)
DEBUG3 (SCK2)
SYS-DI
SYS-DO
Sub-code syn input.
I
CS signal input.
I
Loading motor reverse drive output.
O
Loading motor forward drive output.
O
Power supply.
–
A/D converter reference voltage input.
–
Disc loading switch.
I
Not connected.
–
GND.
–
Not connected.
–
Reset output to IC, LC89513K pin 22. Active “L”.
O
A/D converter reference voltage input.
–
Debug output 1.
O
Debug output 2.
O
Debug output 3.
O
System microprocessor serial data input.
I
System microprocessor serial data output.
O
42
43, 44
45
46
47
48-55
SYS-CLK
NC
I2CD
NC
I2CC
A0-A7
–
O
–
O
I/O
System microprocessor sync clock input.
I
Not connected.
I2C data line to IC, MAS3507D-G10 and IC, DAC3550A-C2.
Not connected.
I2C clock line to IC, MAS3507D-G10 and IC, DAC3550A-C2.
A0-A7 terminal to IC, UT62L1024LC-70LL pin 20-13.
– 30 –
Page 31
Pin No. Pin Name I/O Description
56-63
D0-D7
I/O
D0-D7 terminal to IC, UT62L1024LC-70LL pin 21-23, 25-29 respectively.
64-71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
A8-A15
VSS
A16
CS1
CS2
NC
RD
WR
MP3RST
NC
VDD
DTEN
XCLK
XLAT
XDATA
SQ IN
SCLK
SENS
SQCK
SV-CONT
I/O
–
I/O
O
O
–
O
O
O
–
–
O
O
O
O
O
O
O
A8-A15 terminal to IC, UT62L1024LC-70LL pin 3, 2, 31, 1, 12, 4, 11, 7 respectively.
GND.
A16 terminal to IC, UT62L1024LC-70LL pin 10.
CS1 terminal to IC, UT62L1024LC-70LL pin 30. Active “L”.
CS2 terminal to IC, LC89513K pin 32. Active “L”.
Not connected.
OE terminal to IC, UT62L1024LC-70LL pin 32. Active “L”.
WE terminal to IC, UT62L1024LC-70LL pin 5 and WR terminal to IC, UT62L1024LC-70LL
pin 31. Active “L”.
TE terminal to IC, MAS3507D-G10 pin 1 and POR terminal to IC, MAS3507D-G10 pin 2.
Active “L”.
Not connected.
Power supply.
DTEN terminal to IC, LC89513K pin 55. Active “L”.
DSP serial data transfer clock output.
DSP serial data latch output.
DSP serial data output.
SUB Q/PCM peak/Level data input.
I
SENS serial data clock output.
SENES input.
I
Output clock for reading SQSO.
Output “H” when the power is turned on. (When power is supplied,this pin output “H”
after DSP is initialised.
91
92
93
94
95
96
97
98
99
100
XRST
TE BAL
RF-SW
TEST
APC
CD-MUTE
GFS
C2PO
FOK
LOCK
O
–
O
–
O
O
I/O
I/O
CD reset output.
Not used.
CD/CD-RW switching output.
Connected to VSS.
Laser ON/OFF switching output.
Muting output.
GFS input.
I
C2PO input. Active “L”.
I
FOCUS OK signal input/output.
Output “H” when GFS sampled by 460Hz is “H”, “L” when GFS is “L” continuously
for 8 samplings. Or, a signal is input when LKIN is “1”.
– 31 –
Page 32
IC, LC89513K
Pin No. Pin Name I/O Description
1
VSS
–
GND.
2-8
9
10-16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
RA0-RA6
VSS
RA7-RA13
VSS
RA13
RCS
RWE
ROE
RESET
XTALCK
VDD
C2PO
BCK
SDATA
LRCK
RS
RD
O
Address signal output to data buffer RAM pin.
–
GND.
O
Address signal output to data buffer RAM pin.
–
GND.
O
Address signal output to data buffer RAM pin. Active “L”.
O
Chip select to RAM pin. Active “L”.
O
Data write signal to RAM pin. Active “L”.
O
Data read signal from RAM pin. Active “L”.
I
Reset pin reset at level low. Active “L”.
I
X’tal oscillating circuit input pin.
–
Power supply.
I
C2 pointer input pin.
I
Serial data input clock pin.
I
Serial data input pin.
I
44.1KHz strobe signal input pin.
I
Register select signal pin.
I
CPU data read signal input pin. Active “L”.
31
32
33
34-41
42
43
44
45-48
49
50-53
54
55
56
57-64
WR
CS
VSS
D0-D7
PSRAM
INT
DRQ
HD0-HD3
VSS
HD4-HD7
HRD
DTEN
VDD
I/O0-I/O7
–
I/O
O
O
O
–
O
O
–
I/O
I
CPU data write signal input pin. Active “L”.
I
CS signal input from CPU pin. Active “L”.
GND.
CPU data signal pin with built in pull-up resistor.
I
Pseudo-SRAM select pin.
Interrupt request signal to CPU output pin. Active “L”.
DRQ signal output pin.
Data output to CPU pin.
GND.
Data output to CPU pin.
I
Data read signal input pin. Active “L”.
Data enable signal output pin. Active “L”.
Power supply.
Data buffer RAM data signal pin with built in pull-up resistor.
– 32 –
Page 33
IC, DAC3550A-C2
Pin No. Pin Name I/O Description
1
AGNDC
I/O
Analog reference voltage.
10
11
12
13
14
15
16
17
18
2
3
4
5
6
7
8
9
AVSS1
AVSS0
NC
OUTL
NC
OUTR
NC
AVDDO
AVDD1
NC
XTI
XTO
CLKOUT
SCL
SDA
VSS
VDD
–
O
–
O
–
–
I/O
O
I/O
I/O
I
VSS 1 for audio back-end.
I
VSS 0 for audio output amplifiers.
Not connected.
Audio output: Headphone left or Speaker +. (Not used)
Not connected.
Audio output: Headphone right or Speaker -. (Not used)
Not connected.
I
VDD0 for audio output amplifiers.
I
VDD1 for audio back-end.
Not connected.
I
Quartz oscillator pin 1.
Quartz oscillator pin 2.
Clock output.
I2C clock.
I2C data.
I
Digital VSS.
I
Digital VDD.
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
MCS1
MCS2
DEECTRL
NC
CLI
DAI
WSI
PORQ
TESTEN
NC
AUX2L
AUX2R
AUX1L
AUX1R
NC
DEEML
DEEMR
I
I2C chip select 1.
I
I2C chip select 2.
I
Deemphasis ON/OFF control.
–
Not connected.
I
I2S bit clock.
I
I2S data.
I
I2S frame identification.
I
Power on reset, active “L”.
I
Test enable.
–
Not connected.
I
AUX2 left input for external analog signals (e.g. tape). (Not used)
I
AUX2 right input for external analog signals (e.g. tape). (Not used)
I
AUX1 left input for external analog signals (e.g. FM).
I
AUX1 right input for external analog signals (e.g. FM).
–
Not connected.
O
Deemphasis network left.
O
Deemphasis network right.
36
37
38
39
40
41
NC
FOUTL
FOPL
FINL
NC
FOUTR
–
O
I/O
I/O
–
O
Not connected.
Output to left external filter.
“Filter op amp inverting input, left”.
Input for FOUTL or filter op amp output (line out).
Not connected.
Output to right external filter.
– 33 –
Page 34
Pin No. Pin Name I/O Description
42
FOPR
I/O
Right Filter op amp inverting input.
43
44
FINR
VREF
I/O
Input for FOUTR or filter op amp output (line out).
I
Analog reference ground.
– 34 –
Page 35
IC, MAS3507D-G10
Pin No. Pin Name I/O Description
1
TE
I
Test enable.
10
11
12
13
14
15
16
17
18
2
3
4
5
6
7
8
9
POR
I2CC
I2CD
VDD
VSS
DCEN
EOD
RTR
RTW
DCSG
DCSO
VSENS
PR
PCS
PI19
PI18
PI17
I/O
I/O
–
–
O
O
O
–
O
I/O
I/O
I/O
I
Reset, active “L”.
I2C clock line.
I2C data line.
Positive supply for digital parts.
Ground supply for digital parts.
I
Enable DC/DC converter.
PIO end of DMA, active “L”.
PIO ready to read, active “L”.
PIO ready to write, active “L”.
DC converter transistor ground.
DC converter transistor open drain.
I
DC converter voltage sense.
I
PIO DMA request or read/write.
I
PIO chip select, active “L”.
PIO data [19] (demand pin in SDI mode).
PIO data [18] (MPEG header bit 11-MPEG ID. SDI mode).
PIO data [17] (MPEG header bit 12-MPEG ID. SDI mode).
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
PI16
PI15
PI14
PI13
PI12
SOD (PI11)
SOI (PI10)
SOC (PI9)
PI8
XVDD
XVSS
SID (PI7)
SII (PI6)
SIC (PI5)
PI4
I/O
I/O
I/O
I/O
I/O
O
O
O
O
–
–
O
PIO data [16] (alternative input for SIC. SDI mode).
PIO data [15] (alternative input for SII. SDI mode).
PIO data [14] (alternative input for SID. SDI mode).
PIO data [13] (MPEG header bit 13-Layer ID. SDI mode).
PIO data [12] (MPEG header bit 14-Layer ID. SDI mode).
Serial output data.
Serial output frame identification.
Serial output clock.
I
Start-up: clock output scaler ON/OFF.
Operation: MPEG CRC error.
Positive supply of output buffers.
Ground of output buffers.
I
Serial input data. (Not used)
I
Serial input frame identification.
I
Serial input clock. (Not used)
I
Start-up: select SDI/PI0-DMA input mode.
Operation: MPEG frame Sync.
34
35
PI3
PI2
I
Start-up: enable layer 3 / disable layer 3 decoding.
O
Operation: MPEG header bit 20 (Sampling Frequency).
I
Start-up: enable layer 2 / disable layer 2 decoding.
O
Operation: MPEG header bit 21 (Sampling Frequency).
– 35 –
Page 36
Pin No. Pin Name I/O Description
I
36
37
PI1
PI0
Start-up: SDO: select 32-bit mode / 16-bit I 2S mode.
O
Operation: MPEG header bit 30 (Emphasis).
I
Start-up: Select multimedia mode / broadcast mode.
O
Operation: MPEG header bit 31 (emphasis).
38
39
40
41
42
43
44
CLKO
PUP
WSEN
WRDY
AVDD
CLKI
AVSS
O
Clock output for the D/A converter. (Not used)
O
Power up, i. e. status of voltage supervision. (Not used)
I
Enable DSP and DC/DC converter.
Decoder operation ready. (Not used). If WSEN=0: Valid clock input at CLKI. If WSEN=1:
O
Clock synthesizer PLL locked.
–
Supply for analog circuits.
I
Clock input.
–
Ground supply for analog circuits.
– 36 –
Page 37
VOLTAGE CHART
IC301, LC75374E
PIN NO. VOLT (V)
1 ~ 7 4.32
80
9 0.07
10 ~ 14 4.32
15 0
16 ~ 18 –
19 ~ 24 4.32
25 0.035
26 0
27 ~ 38 4.32
39 8.36
40 ~ 44 4.32
IC501, TA8273H
PIN NO. VOLT (V)
1, 2 0
3 7.6
4 3.65
5 7.6
6 14.35
7 7.6
80
9 7.6
10 8.9
11, 12 1.4
13 0
14, 15 1.42
16 1.35
17 7.6
18 0
19 7.6
20 14.35
21 7.6
22 4.15
23 7.6
24 0
25 0.02
IC601, LC75817W-8720
PIN NO. VOLT (V)
1 ~ 56 3.3
57 ~ 61 –
62 ~ 69 3.3
70, 71 –
72 ~ 75 4.85
76 ~ 80 –
81 4.85 (ILL1)
82 4.85 (ILL2)
83, 84 –
85 5.4
86 8.3
87 6.6
88 5.0
89 3.35
90 1.7
91 ~ 93 0
94 ~ 95 2.7
96 ~ 97 5.4
98 0.45
99 4.65
100 0.25
IC602, SBX1971-52
PIN NO. VOLT (V)
10
2, 3 5.2
IC701, PST994D
PIN NO. VOLT (V)
1 8.7
20
3 4.35
IC751, BA6417F
PIN NO. VOLT (V)
1 0.24
2, 3 8.2
4, 5 –
6 3.64
7 0.25
IC901,
UPD178018AGC-598
PIN NO. VOLT (V)
1, 2 –
3 0.07
4–
5 4.9
6 ~ 9 –
10 0.24
11 0.58
12 4.32
13 0.12
14 4.7
15 1.9
16 4.1
17 3.55
18 4.85
19, 20 –
21 0
22, 23 4.9
24 (–) {4.85}
25 4.9
26, 27 –
28, 29 0.03
30 4.9
31 (2.2) {0.65}
32 (0.35) {2.5}
33 0
34, 35 1.05
36 0
37 –
38 4.75
39 3.2
40 4.9
41 4.9
42 4.85
43 –
44 4.3
45 ~ 57 –
58 5.0
59 –
60 5.22
80
– 37 –
Page 38
TU101, FAE347-A22
PIN NO. VOLT (V)
61 ~ 65 –
66, 67 5.1
68 –
69 (0.7) {5.0}
70 4.3
71, 72 –
73 5.3
74 3.55
75 0
76 1.6
77 1.55
78 3.55
79, 80 4.9
Note:
PIN 24 ( ) = DX, { } = LO
PIN 31,32 ( ) = FM, { } = AM
PIN 69 AUX JACK IN
( ) = OFF, { } = ON
IC903, TC4053BF
PIN NO. VOLT (V)
1 4.25
2 0.12
3 4.85
REF NO. ANODE CATHODE
LED 601 3.4 1.7
LED 602 1.7 0
LED 603 3.3 1.7
LED 604 1.7 0
LED 611 1.7 0
LED 613 3.35 1.7
LED 614 3.5 1.8
LED 615 1.8 0.06
LED 616 3.5 1.8
LED 617 1.8 0.06
LED 618 9.0 5.5
LED 619 9.0 5.15
LED 620 3.35 0
LED 621 3.35 0
LED 622 9.0 5.15
LED 625 3.4 1.7
LED 626 5.0 3.35
PIN NO. FM AM
1 ~ 3 – –
4 7.67 0.28
50 0
6 1.29 ~ 7.45 1.29 ~ 7.45
7, 8 0 0
9 1.6 8.75
10 0 0
11 0.12 0.23
12 8.05 0.03
13 8.26 8.15
14 2.2 ~ 3.68 2.2 ~ 3.68
15 0 0
16, 17 3.33 3.33
18 0 0
19, 20 – –
21 1.58 0.01
22 0.04 4.73
23 0.88 1.05
24 4.0 1.16
25 8.26 8.15
26 1.14 0.05
4 4.7
5 4.55
6 ~ 8 0
9 ~ 11 0.55
12 4.9
13 0.05
14 4.3
15 0.12
16 4.9
– 38 –
Page 39
REF NO. DX LO
Q 101
B––
C 7.14 0.3
E00
Q 102
B 9.0 8.3
C 0.5 8.9
E 9.0 9.0
Q 103
B 8.75 0.04
C 9.0 9.0
E 8.0 –
Q 104
B 4.8 –
C 8.75 0.04
E00
Q 105
B 1.05 1.0
C 0.65 2.2
E 0.6 0.01
Q 106
B 0.6 0.01
C 0.65 2.2
E00
REF NO. OFF ON
Q 341
B – 4.1
C––
E00
Q 342
B – 4.1
C––
E00
Q 401
B00
C 0.04 0.04
E 0.03 0.03
REF NO. OFF ON
Q 403
B – 3.65
C––
E00
Q 404
B – 3.65
C––
E00
Q 405
B – 3.65
C––
E00
Q 406
B – 3.65
C––
E00
REF No. VOLT (V)
Q 451
B 1.5
C 4.7
E 0.9
REF NO. OFF ON
Q 461
B 14.4 0.02
C 0.15 14.3
E 14.3 14.4
Q 462
B – 1.9
C 14.4 0.02
E00
REF NO. ILL1 ILL2
Q 611
B – 0.75
C – 0.06
E0 0
REF NO. OFF ON
Q 613
B 4.85 –
C 0.8 9.0
E 0.75 –
Q 614
B 0.75 –
C 0.09 –
E00
Q 615
B 0.75 –
C 0.09 –
E00
REF NO. VOLT(V)
Q 701
B 13.6
C 14.3
E 14.35
Q 702
B 4.0
C 0.06
E0
Q 704
B 9.7
C 14.35
E 9.0
Q 708
B 6.25
C 13.3
E 5.6
Q 709
B 8.85
C 14.35
E 8.2
REF NO. VOLT(V)
Q 710
B 9.4
C 14.35
E 8.8
Q 711
B 8.75
C 9.4
E 9.45
Q 712
B 2.25
C–
E0
Q 713
B 5.6
C 8.2
E 5.0
Q 715
B 3.0
C–
E0
Q 716
B–
C 5.6
E 5.6
Q 402
B 4.85 4.85
C 0.035 0.035
E00
– 39 –
Page 40
CD TEST MODE
1. Disassembly
1. Remove COVER TOP / COVER BOTTOM.
2. Remove the screws (as shown by arrows in Fig-1) of CD
mechanism. See Fig-1.
2. Service Position
Check the function with the mechanism is set to a stable
position. (Use a tool such as PLATE). See Fig-2.
Fig-1
3. Test Mode
1. Starting the CD Test Mode
1) Short-circuit the TEST land (TP904 - as shown by arrow
in Fig-3) of the MAIN PWB, using solder. See Fig-3.
2) Connect the ACC (red) and BACKUP (yellow) wire of
the power supply/speakers connector to the positive
(+) terminal of the Power Supply device and the
Ground (black) wire to the negative (–) terminal.
3) Adjust the voltage applied to the Power Supply device
to 14.5V and then turn on the power.
The test mode starts, and the LCD are all lit. See Fig-4.
2. Exiting the CD Test Mode
1) Turn off the power of the Power Supply device.
2) Remove all the wires from the power supply/speakers
connector.
3) Remove the solder of the TEST land (TP904) of the
MAIN PWB.
Fig-2
IC901
Fig-3
Fig-4
– 40 –
Page 41
3. CD Test Mode Functions
Mode
Start Mode All lights are lit. Test mode starts.
Button for
Activation
Display Operation Contents
Load/Unload
EJECT VCC on
Search RNDM Continuous focus search. APC circuit check
Mode
Play Mode REP 1 TOC READING Normal playback. Focus servo
Traverse INT Track No. and play Pause status Tracking servo OFF
Mode
STOP REP All lights are lit. Standby status All servo OFF
Sled Mode
• During search mode check, do not insert a disc.
• Press the REPEAT button to exit each mode.
6
5
3
4
TUNE
All lights are lit. Checking All servo off
Laser on
PU lens repeats full swings. (Note 1) Laser current measurement
Focus error waveform check
Track No. If TOC READ is unavailable, the Tracking servo
Play time display search mode function is on. CLV servo
Level display Sled servo
time are displayed
Laser ON/OFF
All lights are lit. Pickup moves to the Sled servo
outermost track. Mechanism function check
Pickup moves to the
innermost track.
Note 1: When the focus search mode is repeated more than 10 minutes, the driver IC may generate heat, activating the protection circuit
to stop the CD function. If this happens, turn off the power, wait for 10 minutes to release heat before restarting.
– 41 –
Page 42
MECHANICAL EXPLODED VIEW 1 / 1
10
9
53
PWB
3
2
16
4
SH LCD
LCD
1
6
PWB
17
8
7
5
15
14
13
A
10
54
12
37
B
I
SH L-BT 18
18
J
SH CABI REAR
A
11
53
E
26
36
35
PWB
23
C
24
D
39
32
H
E
PWB
36
38
L
D
D
21
22
D
25
27
G
G
31
MOT FF-050SK
C
C
D
28
D
33
34
19
C
D
30
42
20
29
E
43
I
45
I
J
CDCO2AW1
46
J
O
47
J
J
L
48
PWB
HLDR
CD-AC
I
44
K
HLDR
P-IC-AC
O
K
N
PANEL HT-SINK
J
M
K
51
52
40
L
41
SH,PWB
J
I
F
50
K
E
49
– 42 –
Page 43
MECHANICAL PARTS LIST 1 / 1
PART NO.
NO.
1 8B-KC6-001-010 WINDOW,LCD MP32 YU
2 8B-KC7-001-010 CABI,FRONT HIGH
3 8B-KC7-004-010 BTN,+/ 4 8B-KC7-005-010 BTN,MUTE
5 8B-KC7-006-010 BTN,TWIN
6 8B-KC7-204-010 CASE,LCD
7 8B-KC7-202-010 LENS,LCD
8 8B-KC7-201-010 PLATE,LENS BOTTOM
9 8B-KC7-002-010 CABI,REAR
10 8B-KC7-222-010 PLATE,MAGNET
11 8B-KC7-025-010 PANEL,BOARD
12 8B-KC7-611-010 PWB,FLEX DISP
13 8B-KC6-002-010 CABI,FRONT AL MP3
14 8B-KC7-008-010 CABI,BTN PANEL B
15 8B-KC7-010-010 BTN,P-SET 7
16 8B-KC7-015-010 LENS,BER
17 8B-KC7-207-010 PLATE,PANEL A’SSY
18 8B-KC7-612-010 PWB,FLEX KEY
19 8A-ZL2-211-110 HLDR ASSY,MOT
20 8A-ZL2-241-010 GEAR,WORM
21 8A-ZL2-242-010 WORM-WHL,
22 8A-ZL2-243-010 GEAR,L-1
23 8B-KC7-209-010 HLDR,SP-L
24 8A-ZL2-231-010 LEVER ASSY,GEAR L
25 8A-ZL2-221-010 LEVER ASSY,L
26 8A-ZL2-201-010 FRAME ASSY,MAIN
27 8A-ZL2-246-010 GEAR,CAM L
28 8A-ZL2-236-010 LEVER ASSY,GEAR R
29 8A-ZL2-226-010 LEVER ASSY,R
30 8B-KC7-210-010 HLDR,SP-R
31 8A-ZL2-247-010 GEAR,CAM R
32 8A-ZL2-244-010 GEAR,L-2
33 8A-ZL2-251-010 SHAFT,COUNTER
34 8A-ZL2-245-010 GEAR,R
35 8B-KC7-208-010 COVER, DUST
36 85-ZL3-203-010 MAGNET,ACU
DESCRIPTIONREF. NO. KANRI
PART NO.
NO.
37 8B-KC7-021-010 CABI,BASE MAIN
38 8B-KC7-022-010 LENS,CD
39 8B-KC1-603-010 F-CABLE,2P (PWB LED)
40 8B-KC7-023-010 CABI,BASE AROUND
41 8B-KC1-213-110 CHAS,SIDE L-BC
42 8B-KC7-212-010 HLDR,TR2-B
43 8Z-KC1-256-010 COVER, BOTTOM RDS
44 8B-KC7-211-010 HLDR,MECHA
45 8B-KC6-201-010 HLDR,STATIC MP3
46 88-KC4-641-010 FF-CABLE, 20P 1.0 90MM
47 8A-KC7-255-010 SPR-C,WIRE
48 8B-KC7-217-010 HLDR,MECHA FR
49 8B-KC1-214-110 CHAS,SIDE R-BC
50 8B-KC7-251-010 COVER, BT-B
51 8B-KC7-024-010 CABI,TRIM
52 8Z-KC1-231-110 HLDR,HALF -C
53 8B-KC7-215-010 SHAFT,FLAP L/R
54 8B-KC7-218-010 TERMINAL,PWB
A 8Z-KC1-253-010 S-SCREW,PT 2*8 BH+ BLK
B 87-B10-335-010 VTT+1.7-4 W/O
C 87-261-032-210 V+2-3
D 87-067-800-010 PW 1.5-3.5-0.25SLT
E 87-251-070-410 U+2.6-3
F 87-432-903-010 WASHER,WTE 2.6
G 87-067-272-010 PW,4-2.1-0.25
H 8Z-KC1-254-010 S-SCREW,PT 2*5 BH+ BLK
I 87-B10-216-010 U+2.6-4.0 ZINC BLK (BH M2.6)
J 8Z-KC1-251-010 S-SCREW,TH2.6-4.0-0.8
K 87-251-073-410 SCREW,U+2.6-6
L 87-B10-336-010 VTT+2.6-6 W/O
M 87-B10-259-010 UT2+3.0-10.0 W/O SLOT (BH TAP)
N 87-251-096-410 U+3-10
O 88-ZG5-317-010 S-SCREW,8ZG5S+2-4 W/O
DESCRIPTIONREF. NO. KANRI
COLOR NAME TABLE
Basic color symbol Color Basic color symbol Color Basic color symbol Color
B Black C Cream D Orange
G Green H Gray L Blue
LT Transparent Blue N Gold P Pink
R Red S Silver ST Titan Silver
T Brown V Violet W White
WT Transparent White Y Yellow YT Transparent Yellow
LM Metallic Blue LL Light Blue GT Transparent Green
LD Dark Blue DT Transparent Orange GM Metallic Green
YM Metallic Yellow DM Metallic Orange PT Transparent Pink
LA Aqua Blue GL Light Green HT Transparent Gray
– 43 –
Page 44
CD MECHANISM EXPLODED VIEW 1 / 1
1
4
SENSOR,
P. C .B
CORD 3P
56
A
5
6
7
55
10
52
51
43
8
7
55
38
42
41
A
B
13
9
15
11
37
2
3
12
14
16
23
C
26
27
36
33
41
40
34
39
A
57
20
21
24
25
LEAD MOTOR A
LEAD MOTOR B
30
31
A
D
DISC,SHEET
19
32
35
17
18
18
22
28
29
17
54
A
53
50
LEAD 2P
47
47
A
49
46
E
48
44
45
– 44 –
Page 45
CD MECHANISM PARTS LIST 1 / 1
PART NO.
NO.
1 S1-100-510-130 COVER TOP
2 S1-100-510-090 LEVER RELEASE
3 S1-100-510-180 ARM START SET
4 S1-100-520-220 LEVER,SENSOR
5 S1-100-540-070 SP LEVER SENSOR
6 S1-100-520-050 DISC ARM L
7 S1-100-530-260 ROLLER ARM DISC
8 S1-100-540-040 SP ARM DISC
9 S1-100-520-060 DISC ARM R
10 S1-100-570-760 SW,LOAD MPU10853MLB2
11 S1-100-520-230 GUIDE TOP
12 S1-100-510-070 PLATE CLAMPER
13 S1-100-520-040 CLAMPER
14 S1-100-740-020 SP ARM CHUCK
15 S1-100-510-030 ARM CHUCK
16 S1-100-740-040 SP ARM CHUCK(R)
17 S2-181-600-50D PSW,1.6-5-0.25 (CUT)
18 S1-100-750-020 LOLLER LOADING
19 S1-100-570-070 SW,INNER
20 S1-100-570-140 LEAD SW A
21 S1-100-570-150 LEAD SW B
22 S1-100-530-060 SHAFT ROLLER
23 S1-100-740-010 SP FEED
24 S1-100-510-110 GUIDE,SPG
25 S1-100-720-040 GUIDE A
26 S1-100-570-790 FLEX PICK(FOC)
27 S1-100-770-090 PICK KSS-710A
28 S1-100-540-100 SP LEVER UP
29 S1-100-520-240 LEVER,UP
30 S1-100-270-030 MOTOR,MAIN FF-030PK
31 S1-100-520-110 GEAR MOTOR FEED
32 S1-100-520-190 CASE,MOTOR
33 S1-100-730-010 SCREW,FEED
34 S1-100-520-090 GEAR,FEED A
35 S1-100-520-300 GEAR FEED B
DESCRIPTIONREF. NO. KANRI
PART NO.
NO.
36 S1-100-520-170 LEVER,R
37 S1-100-520-140 GEAR H CAM
38 S1-100-540-080 SP SUB DAMPER
39 S1-100-510-080 ARM,R
40 S1-100-520-180 LEVER,LOCK
41 S1-100-540-030 DAMPER SP
42 S1-100-520-130 GEAR LOAD
43 S1-100-520-120 GEAR L H
44 SX-100-710-030 CHASSIS ASSY
45 S1-100-520-160 LEVER,KICK
46 S1-100-520-270 LEVER,SUB KICK
47 S1-100-760-010 DAMPER ASSY
48 S1-100-510-060 BRACKET,L M
49 S1-100-520-200 MOTOR WORM
50 S1-100-770-080 MOTOR LOAD
51 S1-100-540-090 SP GEAR SUB
52 S1-100-520-030 GEAR SUB CAM
53 S1-100-520-250 LEVER,SW
54 S1-100-520-210 GEAR,ROLLER
55 S1-100-530-250 PIN ARM DISC
56 S1-100-520-020 GEAR CAM
57 SZ-100-710-010 PICK BASE GROSS ASSY
A S1-100-550-030 SCREW,XP
B S2-139-140-40P B-TYPE M1.4-4
C S2-103-170-60P (+)P. PRECISION SCREW M1.7-6
D S2-103-200-40P (+)P.PRECISION SCREW M2.0-4.0
E S2-101-200-25P (+)P.PRECISION SCREW M2.0-2.5
DESCRIPTIONREF. NO. KANRI
– 45 –
Page 46
ACCESSORIES / PACKAGE LIST
PART NO.
NO.
1 8B-KCF-902-010 IB,INST,YU,YL (3L,P)-I
1 8B-KC6-901-010 IB,YU(3L) MP32
2 8Z-KT1-616-010 CONN ASSY,16P B52
3 87-B10-141-010 NUT,5 TYPE-2
4 87-B10-143-010 UT1+5-15 W/O SLOT
5 87-B10-144-010 W,5.2-10-0.5
6 87-B10-145-010 W-SPR,5.3-8.5-1.5
7 87-B10-216-010 U+2.6-4.0 ZINC BLK (BH M2.6)
8 8Z-KC1-231-110 HLDR,HALF -C
9 8Z-KC1-232-010 KEY,REMOVE -C
10 8Z-KC1-235-010 HLDR,REAR MTG
11 8Z-KC1-244-010 S-SCREW,5*6 TH+ TAPPING ST
12 8Z-KC1-250-010 S-SCREW,HEXAGON
DESCRIPTIONREF. NO. KANRI
– 46 –
Page 47
2–11, IKENOHATA 1–CHOME, TAITO-KU, TOKYO 110, JAPAN TEL:03 (3827) 3111
Printed in Singapore9620450 0251431
Loading...