Aiwa CA-DW637 US Service Manual

CA-DW637

U(S)

SERVICE MANUAL

COMPACT DISC CARRY

COMPONENT SYSTEM

• This Service Manual is the “Revision Publishing” and replaces “Simple Manual” (S/M Code No. 09-003-339-3T1).

BASIC TAPE MECHANISM : ZZM-2 YPR2NF BASIC CD MECHANISM : 3ZG-3 E2NC

S/M Code No. 09-003-339-3R1

REVISION

DATA

SPECIFICATIONS

• Design and specifications are subject to change without notice.

2

PROTECTION OF EYES FROM LASER BEAM DURING SERVICING

This set employs laser. Therefore, be sure to follow carefully the instructions below when servicing.

WARNING!

WHEN SERVICING, DO NOT APPROACH THE LASER EXIT WITH THE EYE TOO CLOSELY. IN CASE IT IS NECESSARY TO CONFIRM LASER BEAM EMISSION. BE SURE TO OBSERVE FROM A DISTANCE OF MORE THAN 30cm FROM THE SURFACE OF THE OBJECTIVE LENS ON THE OPTICAL PICK-UP BLOCK.

Caution: Invisible laser radiation when open and interlocks defeated avoid exposure to beam. Advarsel: Usynling laserståling ved åbning, når sikkerhedsafbrydere er ude af funktion. Undgå udsættelse for stråling.

VAROITUS!

Laiteen Käyttäminen muulla kuin tässä käyttöohjeessa mainitulla tavalla saattaa altistaa käyt-täjän turvallisuusluokan 1 ylittävälle näkymättömälle lasersäteilylle.

CAUTION

Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.

ATTENTION

L'utilisation de commandes, réglages ou procédures autres que ceux spécifiés peut entraîner une dangereuse exposition aux radiations.

ADVARSEL!

Usynlig laserståling ved åbning, når sikkerhedsafbrydereer ude af funktion. Undgå udsættelse for stråling.

This Compact Disc player is classified as a CLASS 1 LASER product. The CLASS 1 LASER PRODUCT label is located on the rear exterior.

VARNING!

Om apparaten används pŒ annat sätt än vad som specificeras i denna bruksanvising, kan användaren utsättas för osynling laserstrŒlning, som överskrider gränsen för laserklass 1.

Precaution to replace Optical block (KSS-213F)

Body or clothes electrostatic potential could ruin laser diode in the optical block. Be sure ground body and workbench, and use care the clothes do not touch the diode.

1) After the connection, remove solder shown in the right figure.

3

ELECTRICAL MAIN PARTS LIST

REF. NO PART NO. KANRI DESCRIPTION

IC 87-A20-446-010 C-IC,LA9241ML

8A-CT4-625-010 C-IC,LC867232A 87-A21-576-010 IC,TA2104BN 87-A21-185-040 C-IC,LC72121M 87-A20-459-010 C-IC,LC78622ED

87-A20-914-010 IC,SPS-442-1-F 87-A21-093-010 IC,LA6541D 87-001-982-010 IC,TA7291S 87-A21-416-040 C-IC,M61500FP 87-017-889-010 IC,NJM4558LD

87-070-417-010 IC,NJM4558 DD 87-A21-020-010 IC,TA8223K 87-001-132-010 FUSE, ICP-N38 87-A21-213-010 IC,BA17808T 87-070-416-010 IC,NJU7201 L55

TRANSISTOR 89-319-233-080 TR,2SC1923 (0.1W)

87-026-291-080 TR,DTC124XS 87-A30-197-080 TR,KTA1267GR 87-026-464-080 TR,DTC114TS (0.3W) 87-026-610-080 TR,KTC3198GR

87-026-218-080 TR,DTC144ES (0.2W) 87-026-215-080 TR,DTC114YS 87-026-287-080 TR,DTC143ES 89-113-187-880 TRNSISTOR,2SA1318 (0.5W) 89-112-964-580 TR,2SA1296Y 0.75W 120M

89-406-555-080 TR,2SD655 (0.5W) 87-A30-090-080 FET,2SK2541 87-A30-091-080 FET,2SJ460 89-320-011-080 TR,2SC2001 (15W) 87-026-214-080 TR,DTA114YS (0.3W)

87-A30-219-080 TR,2SB1443(Q) 87-026-219-080 TR,DTA144ES (0.3W) 89-109-521-080 TR,2SA952 (0.6W)

DIODE 87-020-465-080 DIODE,1SS133 (110MA)

87-070-345-080 DIODE,IN4148 87-A40-683-080 ZENER,HZ7A3LTD 87-017-084-080 ZENER,HZS4C3 87-017-072-080 ZENER,HZS3B1

87-A40-466-080 ZENER,MTZJ2.7A 87-A40-156-080 DIODE,1N5392 87-017-139-080 ZENER,HZS15-2

MAIN C.B C1 87-010-314-080 C-CAP,S 22P-50V

C2 87-010-316-080 C-CAP,S 33P-50 CH C3 87-010-314-080 C-CAP,S 22P-50V C5 87-010-196-080 CHIP CAPACITOR,0.1-25 C6 87-010-313-080 CAP, CHIP 18P

C7 87-014-049-080 CAP,PP 470P-100 J C8 87-012-349-080 C-CAP,S 1000P-50 CH C10 87-010-197-080 CAP, CHIP 0.01 DM C11 87-010-197-080 CAP, CHIP 0.01 DM C12 87-010-197-080 CAP, CHIP 0.01 DM

C13 87-010-150-080 C-CAP,S 6P-50 CH C14 87-010-303-080 C-CAP,S 330P-50CH C15 87-012-349-080 C-CAP,S 1000P-50 CH C16 87-010-380-080 CAP, ELECT 47-16V C17 87-010-198-080 CAP, CHIP 0.022

C18 87-015-819-080 CAPACITOR,0.01 C19 87-010-112-080 CAP, ELECT 100-16V C20 87-010-404-080 CAP, ELECT 4.7-50V C21 87-010-197-080 CAP, CHIP 0.01 DM

NO.

REF. NO PART NO. KANRI DESCRIPTION

C22 87-010-197-080 CAP, CHIP 0.01 DM C23 87-010-197-080 CAP, CHIP 0.01 DM C24 87-010-303-080 C-CAP,S 330P-50CH C25 87-016-460-080 C-CAP,S 0.22-16 B C27 87-A11-067-080 C-CAP,S 1-10 K B

C28 87-016-669-080 C-CAP,S 0.1-25 K B C29 87-016-669-080 C-CAP,S 0.1-25 K B C30 87-010-198-080 CAP, CHIP 0.022 C31 87-010-198-080 CAP, CHIP 0.022 C33 87-010-401-080 CAP, ELECT 1-50V

C34 87-010-401-080 CAP, ELECT 1-50V C35 87-015-819-080 CAPACITOR,0.01 C36 87-010-112-080 CAP, ELECT 100-16V C37 87-010-197-080 CAP, CHIP 0.01 DM C38 87-010-380-080 CAP, ELECT 47-16V

C39 87-010-404-080 CAP, ELECT 4.7-50V C40 87-010-197-080 CAP, CHIP 0.01 DM C41 87-012-349-080 C-CAP,S 1000P-50 CH C42 87-012-349-080 C-CAP,S 1000P-50 CH C43 87-012-349-080 C-CAP,S 1000P-50 CH

C44 87-010-311-080 CAP 12P C45 87-010-312-080 C-CAP,S 15P-50 CH C47 87-010-197-080 CAP, CHIP 0.01 DM C48 87-010-197-080 CAP, CHIP 0.01 DM C49 87-012-157-080 C-CAP,S 330P-50 CH

C50 87-010-197-080 CAP, CHIP 0.01 DM C56 87-018-131-080 CAP, CER 1000P-50V C57 87-018-115-080 CAP, CER 47P-50V C58 87-016-669-080 C-CAP,S 0.1-25 K B C59 87-016-669-080 C-CAP,S 0.1-25 K B

C211 87-010-546-080 CAP, ELECT 0.33-50V C212 87-010-546-080 CAP, ELECT 0.33-50V C213 87-010-401-080 CAP, ELECT 1-50V C214 87-010-401-080 CAP, ELECT 1-50V C215 87-010-401-080 CAP, ELECT 1-50V

C216 87-010-401-080 CAP, ELECT 1-50V C217 87-010-248-080 CAP, ELECT 220-10V C220 87-010-545-080 CAP, ELECT 0.22-50V C221 87-010-545-080 CAP, ELECT 0.22-50V C223 87-010-545-080 CAP, ELECT 0.22-50V

C224 87-010-545-080 CAP, ELECT 0.22-50V C225 87-018-205-080 CAP, CERA-SOL 0.022 C226 87-010-248-080 CAP, ELECT 220-10V C227 87-010-401-080 CAP, ELECT 1-50V C228 87-010-401-080 CAP, ELECT 1-50V

C229 87-018-209-080 CAP, CER 0.1-50V C230 87-010-401-080 CAP, ELECT 1-50V C231 87-010-401-080 CAP, ELECT 1-50V C232 87-010-404-080 CAP, ELECT 4.7-50V C233 87-010-401-080 CAP, ELECT 1-50V

C234 87-010-401-080 CAP, ELECT 1-50V C260 87-010-405-080 CAP, ELECT 10-50V C301 87-018-131-080 CAP, CER 1000P-50V C302 87-018-131-080 CAP, CER 1000P-50V C303 87-018-130-080 CAP,TC-U 820P-50 B

C304 87-018-130-080 CAP,TC-U 820P-50 B C305 87-010-263-080 CAP, ELECT 100-10V C306 87-010-263-080 CAP, ELECT 100-10V C309 87-018-130-080 CAP,TC-U 820P-50 B C310 87-018-130-080 CAP,TC-U 820P-50 B

C311 87-010-546-080 CAP, ELECT 0.33-50V C312 87-010-546-080 CAP, ELECT 0.33-50V C315 87-018-205-080 CAP, CERA-SOL 0.022 C321 87-018-131-080 CAP, CER 1000P-50V C331 87-018-126-080 CAP,TC-U 390P-50 B

C332 87-018-126-080 CAP,TC-U 390P-50 B C333 87-018-124-080 CAP, CER 270P-50V C334 87-018-123-080 CAP, CER 220P-50V C340 87-010-374-080 CAP, ELECT 47-10V C341 87-018-209-080 CAP, CER 0.1-50V

NO.

4

REF. NO PART NO. KANRI DESCRIPTION

C343 87-018-123-080 CAP, CER 220P-50V C344 87-018-123-080 CAP, CER 220P-50V C355 87-018-132-080 CAP, CER 2200P-16V C356 87-018-132-080 CAP, CER 2200P-16V C369 87-018-118-080 CAP,TC-U 82P-50 B

C370 87-018-118-080 CAP,TC-U 82P-50 B C371 87-018-205-080 CAP, CERA-SOL 0.022 C373 87-010-401-080 CAP, ELECT 1-50V C374 87-010-401-080 CAP, ELECT 1-50V C382 87-010-401-080 CAP, ELECT 1-50V

C383 87-010-374-080 CAP, ELECT 47-10V C384 87-010-402-080 CAP, ELECT 2.2-50V C385 87-010-405-080 CAP, ELECT 10-50V C386 87-018-198-080 CAP,TC-U 2700P-16 X C387 87-018-198-080 CAP,TC-U 2700P-16 X

C388 87-018-198-080 CAP,TC-U 2700P-16 X C601 87-010-401-080 CAP, ELECT 1-50V C602 87-010-401-080 CAP, ELECT 1-50V C603 87-018-208-080 CAP 0.047-50F C604 87-018-208-080 CAP 0.047-50F

C605 87-018-132-080 CAP, CER 2200P-16V C606 87-018-132-080 CAP, CER 2200P-16V C607 87-010-406-080 CAP, ELECT 22-50 C608 87-010-406-080 CAP, ELECT 22-50 C609 87-010-260-080 CAP, ELECT 47-25V

C610 87-018-209-080 CAP, CER 0.1-50V C613 87-010-263-080 CAP, ELECT 100-10V C614 87-010-263-080 CAP, ELECT 100-10V C615 87-010-376-090 CAP 10-2200 C616 87-010-376-090 CAP 10-2200

C623 87-010-546-080 CAP, ELECT 0.33-50V C624 87-010-546-080 CAP, ELECT 0.33-50V C625 87-010-404-080 CAP, ELECT 4.7-50V C641 87-010-248-080 CAP, ELECT 220-10V C643 87-010-387-080 CAP,E 470-25 SME

C644 87-010-260-080 CAP, ELECT 47-25V C720 87-010-405-080 CAP, ELECT 10-50V C722 87-010-385-080 CAP, ELECT 220-25V C723 87-010-248-080 CAP, ELECT 220-10V C724 87-018-205-080 CAP, CERA-SOL 0.022

C726 87-010-404-080 CAP, ELECT 4.7-50V C727 87-010-385-080 CAP, ELECT 220-25V C728 87-010-385-080 CAP, ELECT 220-25V C731 87-018-205-080 CAP, CERA-SOL 0.022 C741 87-010-384-080 CAP, ELECT 100-25V

C750 87-010-404-080 CAP, ELECT 4.7-50V C751 87-010-405-080 CAP, ELECT 10-50V C753 87-010-385-080 CAP, ELECT 220-25V C754 87-010-405-080 CAP, ELECT 10-50V C761 87-010-928-090 CAP,E 4700-25 SMG

C800 87-010-378-080 CAP, ELECT 10-16V C1832 87-018-209-080 CAP, CER 0.1-50V CF1 87-A91-094-010 FLTR,CDA10.7 MG80A CF2 82-785-747-080 CF,MS2 GHY,R CF3 82-785-747-080 CF,MS2 GHY,R

CN201 87-099-719-010 CONN,30P TYK-B(X) CN203 87-A60-623-010 CONN,6P V 2MM JMT CN301 87-A60-622-010 CONN,5P V 2MM JMT CN302 87-A60-621-010 CONN,4P V 2MM JMT CN701 87-A60-621-010 CONN,4P V 2MM JMT

CN751 87-A60-626-010 CONN,9P V 2MM JMT ICP705 87-002-330-010 FUSE UNIT,ICP-N5 J202 87-A60-354-010 JACK,PIN 2P MSP -242V-05 J601 87-A60-420-010 JACK,3.5 ST (MSC) J602 87-A60-217-010 TERMINAL,SPKR 4P

L2 87-A50-347-010 COIL,FM BPF EX L3 8Z-CT4-616-010 BAR-ANT,MW2B L4 87-A50-420-010 COIL,MW OSC(SYN) L5 87-A50-424-010 COIL,FM RF EX(SYN) L6 87-A50-454-010 COIL,FM OSC U(SYN)

NO.

REF. NO PART NO. KANRI DESCRIPTION

L7 87-A91-308-010 FLTR,PCFAZH- 450T (TOK) L8 87-005-849-080 COIL,10UH(CECS) L9 87-005-849-080 COIL,10UH(CECS) L331 87-007-342-010 COIL,OSC 85K BIAS L601 87-A50-087-080 COIL,100UH (CECS)

L602 87-A50-087-080 COIL,100UH (CECS) R607 87-029-124-010 RES,FUSE 2.2-1/4 R608 87-029-124-010 RES,FUSE 2.2-1/4 SCR3 87-A40-616-080 VARI-CAP,SVC384(S/T) SCR4 87-A40-615-040 VARI-CAP,KV1311NT

SCR5 87-A40-615-040 VARI-CAP,KV1311NT SFR751 87-024-354-080 SFR,22K DIA6 H TC1 87-011-254-080 TRIMER,20P LAR X1 87-A70-061-010 VIB,XTAL 4.500MHZ CSA-309

FRONT C.B C1 87-010-196-080 CHIP CAPACITOR,0.1-25

C2 87-010-196-080 CHIP CAPACITOR,0.1-25 C3 87-010-196-080 CHIP CAPACITOR,0.1-25 C6 87-010-196-080 CHIP CAPACITOR,0.1-25 C7 87-010-400-080 CAP, ELECT 0.47-50V

C8 87-010-401-080 CAP, ELECT 1-50V C10 87-010-405-080 CAP, ELECT 10-50V C12 87-010-374-080 CAP, ELECT 47-10V C13 87-010-178-080 CHIP CAP 1000P C15 87-010-321-080 CHIP CAPACITOR,82P(J)

C16 87-010-318-080 C-CAP,S 47P-50 CH C17 87-010-321-080 CHIP CAPACITOR,82P(J) C18 87-A10-189-040 CAP,E 220-10 C19 87-A10-189-040 CAP,E 220-10 C21 87-010-196-080 CHIP CAPACITOR,0.1-25

C22 87-010-196-080 CHIP CAPACITOR,0.1-25 C23 87-010-196-080 CHIP CAPACITOR,0.1-25 C73 87-010-178-080 CHIP CAP 1000P C98 87-010-263-080 CAP, ELECT 100-10V C101 87-010-545-080 CAP, ELECT 0.22-50V

C200 87-010-312-080 C-CAP,S 15P-50 CH C201 87-010-314-080 C-CAP,S 22P-50V C401 87-010-182-080 C-CAP,S 2200P-50 B C403 87-012-154-080 C-CAP,S 150P-50 CH C404 87-010-401-080 CAP, ELECT 1-50V

C405 87-010-545-080 CAP, ELECT 0.22-50V C406 87-010-178-080 CHIP CAP 1000P C407 87-010-405-080 CAP, ELECT 10-50V C408 87-010-248-080 CAP, ELECT 220-10V C409 87-010-248-080 CAP, ELECT 220-10V

C410 87-010-405-080 CAP, ELECT 10-50V C414 87-012-153-080 C-CAP,S 120P-50 CH CN1 87-099-720-010 CONN,30P TYK-B(P) CN2 88-CT4-610-010 CONN ASSY,10P D4 87-001-519-010 LIGHT EMITTING DIODE,SLR-37

D5 87-A40-410-010 LED,SEL2515C PGRN D6 87-A40-410-010 LED,SEL2515C PGRN D7 87-A40-410-010 LED,SEL2515C PGRN D8 87-A40-410-010 LED,SEL2515C PGRN D9 87-001-519-010 LIGHT EMITTING DIODE,SLR-37

D10 87-001-519-010 LIGHT EMITTING DIODE,SLR-37 D11 87-001-519-010 LIGHT EMITTING DIODE,SLR-37 D21 87-A40-161-010 LED,L-1154SGD D25 87-A40-161-010 LED,L-1154SGD D27 87-A40-161-010 LED,L-1154SGD

D29 87-A40-161-010 LED,L-1154SGD D31 87-A40-161-010 LED,L-1154SGD D33 87-A40-161-010 LED,L-1154SGD D35 87-A40-161-010 LED,L-1154SGD J401 87-A60-651-010 JACK,3.5MONO

L1 87-003-171-010 COIL,15UH TROIDAL L11 87-003-171-010 COIL,15UH TROIDAL L401 87-A50-067-080 COIL,1.00UH (CECS)

NO.

5

REF. NO PART NO. KANRI DESCRIPTION

LCD1 8Z-CT4-607-110 LCD,AIW4176 S40 87-A90-483-080 SW,TACT TS2101 S41 87-A90-483-080 SW,TACT TS2101 S43 87-A90-483-080 SW,TACT TS2101 S44 87-A90-483-080 SW,TACT TS2101

S45 87-A90-483-080 SW,TACT TS2101 S46 87-A90-483-080 SW,TACT TS2101 S47 87-A90-483-080 SW,TACT TS2101 S48 87-A90-483-080 SW,TACT TS2101 S49 87-A90-483-080 SW,TACT TS2101

S50 87-A90-483-080 SW,TACT TS2101 S51 87-A90-483-080 SW,TACT TS2101 S52 87-A90-483-080 SW,TACT TS2101 S53 87-A90-483-080 SW,TACT TS2101 S54 87-A90-483-080 SW,TACT TS2101

S55 87-A90-483-080 SW,TACT TS2101 S56 87-A90-483-080 SW,TACT TS2101 S57 87-A90-483-080 SW,TACT TS2101 S58 87-A90-483-080 SW,TACT TS2101 S59 87-A90-483-080 SW,TACT TS2101

S60 87-A90-483-080 SW,TACT TS2101 S61 87-A90-483-080 SW,TACT TS2101 VR401 82-NK7-615-010 VR,10KA RK11K1130 X1 87-030-273-010 VIB,XTAL 32.768K5PPM X2 87-A70-070-080 VIB,CER 5.76MHZ CRHF

CD C.B C1 87-010-403-080 CAP, ELECT 3.3-50V

C2 87-010-197-080 CAP, CHIP 0.01 DM C3 87-010-263-080 CAP, ELECT 100-10V C4 87-010-248-080 CAP, ELECT 220-10V C5 87-010-197-080 CAP, CHIP 0.01 DM

C6 87-010-374-080 CAP, ELECT 47-10V C7 87-010-178-080 CHIP CAP 1000P C9 87-010-248-080 CAP, ELECT 220-10V C10 87-010-263-080 CAP, ELECT 100-10V C12 87-010-401-080 CAP, ELECT 1-50V

C14 87-010-405-080 CAP, ELECT 10-50V C16 87-010-545-080 CAP, ELECT 0.22-50V C17 87-012-157-080 C-CAP,S 330P-50 CH C22 87-010-183-080 C-CAP,S 2700P-50 B C25 87-010-176-080 C-CAP,S 680P-50 SL

C29 87-010-186-080 CAP,CHIP 4700P C30 87-012-156-080 C-CAP,S 220P-50 CH C31 87-010-545-080 CAP, ELECT 0.22-50V C32 87-010-374-080 CAP, ELECT 47-10V C33 87-010-401-080 CAP, ELECT 1-50V

C34 87-010-184-080 CHIP CAPACITOR 3300P(K) C35 87-010-197-080 CAP, CHIP 0.01 DM C36 87-010-374-080 CAP, ELECT 47-10V C37 87-010-404-080 CAP, ELECT 4.7-50V C38 87-010-196-080 CHIP CAPACITOR,0.1-25

C39 87-010-178-080 CHIP CAP 1000P C40 87-010-145-080 C-CAP,S 1P-50 CH C42 87-010-312-080 C-CAP,S 15P-50 CH C45 87-010-196-080 CHIP CAPACITOR,0.1-25 C46 87-010-196-080 CHIP CAPACITOR,0.1-25

C47 87-010-196-080 CHIP CAPACITOR,0.1-25 C48 87-010-315-080 C-CAP,S 27P-50 CH C50 87-012-140-080 CAP 470P C51 87-012-156-080 C-CAP,S 220P-50 CH C57 87-010-316-080 C-CAP,S 33P-50 CH

C58 87-010-316-080 C-CAP,S 33P-50 CH C59 87-010-263-080 CAP, ELECT 100-10V C60 87-010-196-080 CHIP CAPACITOR,0.1-25 C61 87-010-196-080 CHIP CAPACITOR,0.1-25 C62 87-010-186-080 CAP,CHIP 4700P

C65 87-010-404-080 CAP, ELECT 4.7-50V C66 87-010-196-080 CHIP CAPACITOR,0.1-25

NO.

REF. NO PART NO. KANRI DESCRIPTION

C67 87-010-263-080 CAP, ELECT 100-10V C69 87-012-154-080 C-CAP,S 150P-50 CH C70 87-010-263-080 CAP, ELECT 100-10V C71 87-010-197-080 CAP, CHIP 0.01 DM C72 87-010-221-080 CAP, ELECT 470-10V

C73 87-010-197-080 CAP, CHIP 0.01 DM C78 87-010-221-080 CAP, ELECT 470-10V C79 87-010-197-080 CAP, CHIP 0.01 DM C80 87-010-544-080 CAP, ELECT 0.1-50V C81 87-010-405-080 CAP, ELECT 10-50V

C82 87-010-405-080 CAP, ELECT 10-50V C83 87-012-157-080 C-CAP,S 330P-50 CH C84 87-012-157-080 C-CAP,S 330P-50 CH C89 87-010-197-080 CAP, CHIP 0.01 DM C91 87-010-197-080 CAP, CHIP 0.01 DM

C92 87-010-221-080 CAP, ELECT 470-10V C98 87-010-322-080 C-CAP,S 100P-50 CH C99 87-010-178-080 CHIP CAP 1000P C101 87-010-197-080 CAP, CHIP 0.01 DM C102 87-010-263-080 CAP, ELECT 100-10V

C111 87-010-196-080 CHIP CAPACITOR,0.1-25 C112 87-010-196-080 CHIP CAPACITOR,0.1-25 C130 87-012-140-080 CAP 470P C1101 87-010-221-080 CAP, ELECT 470-10V CN1 87-A60-424-010 CONN,16P V TOC-B

CN2 87-A60-131-010 CONN,6P V FE CN4 87-A60-627-010 CONN,10P V 2MM JMT CN5 88-CT4-612-010 CONN ASSY,6PAF CN101 87-A60-130-010 CONN,5P V FE L1 87-005-849-080 COIL,10UH(CECS)

L2 87-005-849-080 COIL,10UH(CECS) L1101 87-005-849-080 COIL,10UH(CECS) SFR1 87-024-357-080 SFR,100K DIA6 H X1 81-592-641-010 VIB,CER 16.93MHZ

AC C.B C701 87-018-205-080 CAP, CERA-SOL 0.022

C702 87-018-205-080 CAP, CERA-SOL 0.022 C703 87-018-205-080 CAP, CERA-SOL 0.022 C704 87-018-205-080 CAP, CERA-SOL 0.022 F380 87-035-488-010 FUSE,3.15A 125V D UL

FC1 87-033-213-080 CLAMP, FUSE FC2 87-033-213-080 CLAMP, FUSE

DRIVE C.B M20 87-045-358-010 MOT,RF-310TA 43

M21 87-045-356-010 MOT,RF-310TA 30 SW1 87-A90-042-010 SW,LEAF MSW-17310MVP0

LOAD C.B CN4 87-099-210-010 CONN,5P 6216 H

M1 87-045-305-010 MOTOR, RF-500TB DC-5V (2MA) SW1 87-036-110-010 PUSH SWITCH SW2 87-036-110-010 PUSH SWITCH

NO.

6

LCD DISPLAY

• Regarding connectors, they are not stocked as they are not the initial order items. The connectors are available after they are supplied from connector manufacturers upon the order is received.

QSURROUND

TRANSISTOR ILLUSTRATION

E C B

DTA114YS DTA144ES DTC114YS DTC124XS DTC144ES KTA1267

E C B

2SA952 2SC1923 2SC2001 2SD655 KTC3198

E C B

2SB1443

S D G

2SJ460 2SK2541

QSURROUND

87

WIRING-1 (MAIN)

1

A

B

C

D

234567

JW005

8

9

10

11 12 13

14

E

F

G

H

I

J

K

109

SCHEMATIC DIAGRAM-1 (MAIN)

1211

WIRING-2 (FRONT)

1

A

B

C

D

234567

8

9

10

11 12 13

14

E

F

G

H

I

J

K

13 14

SCHEMATIC DIAGRAM-2 (FRONT)

1615

WIRING-3 (CD)

1

A

B

C

D

234567

8

9

10

11 12 13

14

E

F

G

H

I

J

K

1817

SCHEMATIC DIAGRAM-3 (CD)

2019

SEMICONDUCTOR FUNCTION AND VOLTAGE CHART

2221

2423

2625

ELECTRICAL ADJUSTMENT

MAIN C.B

L002

IC001

L005

L006

TC001

L007

L004

JW005

< TUNER SECTION >

1. AM VT Adjustment Settings: • Test point: JW005

• Adjustment location: L004

Method: Set to AM 1710kHz adjust L004 so that the test

point becomes 6.0V±0.05V.

2. AM Tracking Adjustment

L003 (Bar-Ant.), L007 ........................................... 600kHz

TC001 ................................................................... 1400kHz

3. FM VT Adjustment Settings: • Test point: JW005

• Adjustment location: L006

Method: Set to FM 108.0MHz adjust L006 so that the test

point is 5.5V±0.2V.

4. FM Tracking Adjustment

L005, L002 ........................................................... 87.5MHz

< TAPE SECTION >

5. Tape speed Adjustment (DECK2) Settings: • Test tape: TTA-1101

• Adjustment location: SFR751

Method: Play back the test tape with DECK1 and adjust

SFR751 so that the output frequency is 3000Hz. After the adjustment, check that the frequency of DECK2 is 3000±45Hz.

6. Azimuth Adjustment (DECK1, DECK2) Settings: • Test tape: TTA-1420

• Adjustment location: Head azimuth adjustment screw

Method: Play back the 8kHz signal of the test tape and

adjust screw so that the output becomes maximum. Next, perform on each FWD PLAY and REV PLAY mode.

L003

RPH (DECK1) / PH (DECK2)

SFR751

PRACTICAL SERVICE FIGURE

< TUNER SECTION >

< FM SECTION >

Sensitivity: 18±5dB (87.5MHz) (THD 3%) 18±5dB (98.0MHz)

18±5dB (108.0MHz) Signal to Noise Ratio: 65±5dB (98MHz) (Input 54dB) Distortion: Less than 2% (98MHz) (Input 54dB) Intermediate frequency: 10.7MHz Stereo separation: More than 22dB

< AM SECTION >

Sensitivity: 54dB±5dB (600kHz) (S/N 10dB) 53dB±5dB (1000kHz)

49dB±5dB (1400kHz) Distortion: Less than 5% (1000kHz) (Input 74dB) Intermediate frequency: 450kHz±1.2kHz

< CASSETTE SECTION >

Tape speed: 3000Hz±45 Wow & flutter: Less than 0.38% (JIS RMS) Take-up torque: 30-60g-cm (DECK 1/2) F.F torque: 55-140g-cm (DECK 1/2) Rew torque: 55-140g-cm (DECK 1/2) Back tension: 3±2g-cm S/N ratio: More than 40dB Distortion: Less than 3.0% (PB) Noise (PB): Less than 1mV (AC/DC, MIN) Erasing Ratio (W/FILTER): More than 50dB

2827

IC BLOCK DIAGRAM

PROTECTOR

CIRCUIT

(TSD)

STOP

BRAKE

: HI IMPEDANCE

NOTE : INPUT

H ACTIVE

IC LA6541D

IC TA2104BN

IC M61500FP

INA1

INB1

INC1

IND1

INE1

FM RF

OUT

RF VCC

AM RF

IN FM OSC AM OSC OSC OUT ST LED IF REQ DET OUT LPF1 LPF2

24 23 22 21 20 19 18 17 16 15 14 13

FMRF

AM MIX

FM

OSC

FM

MIX

AM

OSC

BUFF

LEVEL

DET

ST

1/8

IF

REQ

SW

BUFF

IF

BUFF

AM

DET

FMIFAMIF

AF

AGC

FM

DET

AF

ST/MO FM/AM

VCO

DIVIDE

DECODE

MUTE

1 2 3 4 5 6 7 8 9 10 11 12

RF GND FM RF IN AM LOW

1

2

3

4

5

Mono.SW

MUTE

VOL VOL

24

INA2

23

INB2

22

INC2

21

IND2

20

INE2

IC TA7291S

MIX OUT VCC AM IF IN FM IF IN GND AGC QUAD R-OUT L-OUT

CUT

IC LC72121M

VSSX

QF1

QF2

TONEH1

TONEL1

OUT1

GND

VDD

Bass boost

Treble boost

19

QF4

QF3

18

TONEH2

17

TONEL2

16

15

OUT2

14

VSS

1312

CONT

VSSA

Treble boost

6

7

8

9

10

11

QSurround

ATT ATT

Bass boost

Control logic

VDD

VSSD

3029

IC DESCRIPTION IC, LA9241ML

Pin No. Pin Name I/O Description

Pin to which external pickup photo diode is connected. RF signal is created by adding

I

with the FIN1 pin signal. FE signal is created by subtracting from the FIN1 pin signal.

I

Pin to which external pickup photo diode is connected.

Pin to which external pickup photo diode is connected. TE signal is created by

I

subtracting from the F pin signal.

I

Pin to which external pickup photo diode is connected.

I

DC component of the TE signal is input.

Pin to which external resistor setting the TE signal gain is connected between the TE

I

pin.

O

TE signal output pin.

TES “Track Error Sense” comparator input pin. TE signal is passed through a band-

I

pass filter then input.

I

Shock detection signal input pin.

I

Tracking gain time constant setting pin.

O

TA amplifier output pin.

Pin to which external tracking phase compensation constants are connected between

I

the TD and VR pins.

I

Tracking phase compensation setting pin.

I

Tracking jump signal (kick pulse) amplitude setting pin.

O

Tracking control signal output pin.

O

Focusing control signal output pin.

Pin to which external focusing phase compensation constants are connected between

I

the FD and FA pins.

Pin to which external focusing phase compensation constants are connected between

I

the FDÐ and FAÐ pins.

Pin to which external focusing phase compensation constants are connected between

I

the FA and FE pins.

O

FE signal output pin.

I

Pin to which external FE signal gain setting resistor is connected between the FE pin.

Analog signal GND.

O

Signal ended output of the CV+and CV- pin input signal.

I

Spindle amp input.

I

Pin to which external spindle gain setting resistor in 12 cm mode is connected.

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

25

1

2

3

4

5

6

7

8

9

FIN2

FIN1

E

F

TB

TE-

TE

TESI

SCI

TH

TA

TD-

TD

JP

TO

FD

FD-

FA

FA-

FE

FE-

AGND

SP

I

SPG

—

Pin No. Pin Name I/O Description

35

36

37

38

39, 40

41

42

43

44

45

46

47

48

49

50

51

52

53

54

55

56

57

58

59

60

61

62

63

64

TOFF

TES

HFL

SLOF

CVÐ, CV+

RFSM

RFS-

SLC

SLI

DGND

FSC

TBC

NC

DEF

CLK

CL

DAT

CE

DRF

FSS

VCC2

REFI

VR

LF2

PH1

BH1

LDD

LDS

VCC1

—

I

Tracking off control signal input pin from DSP. Off when TOFF = H.

O

Pin from which TES signal is output to DSP.

“High Frequency Level” is used to judge whether the main beam position is on top of

O

bit or on top of mirror.

I

Sled servo off control input pin.

I

CLV error signal input pin from DSP.

O

RF output pin.

RF gain setting and EFM signal 3T compensation constant setting pin together with

I

RFSM pin.

“Slice Level Control” is the output pin which controls the RF signal data slice level by

O

DSP.

I

Input pin which control the data slice level by the DSP.

Digital system GND.

O

Output pin to which external focus search smoothing capacitor is connected.

I

“Tracking Balance Control” EF balance variable range setting pin.

No connection.

O

Disc defect detector output pin.

I

Reference clock input pin. 4.23 MHz of the DSP is input.

I

Microprocessor command clock input pin.

I

Microprocessor command data input pin.

I

Microprocessor command chip enable input pin.

O

“Detect RF” RF level detector output.

I

“Focus Search Select” focus search mode (± search/+ search) select pin.

Servo system and digital system Vcc pin.

Pin to which external bypass capacitor for reference voltage is connected.

O

Reference voltage output pin.

I

Disc defect detector time constant setting pin.

I

Pin to which external capacitor for RF signal peak holding is connected.

I

Pin to which external capacitor for RF signal bottom holding is connected.

O

APC circuit output pin.

I

APC circuit input pin.

RF system Vcc pin.

26

27

28

29

30, 31

32, 33

34

SP-

SPD

SLEQ

SLD

SL-, SL+

JP-, JP+

TGL

Pin to which external spindle phase compensation constants are connected together

I

with SPD pin.

O

Spindle control signal output pin.

I

Pin to which external sled phase compensation constants are connected.

O

Sled control signal output pin.

I

Sled advance signal input pin from microprocessor.

I

Tracking jump signal input pin from DSP.

I

Tracking gain control signal input from DSP. Low gain when TGL = H.

3231

IC, LC78622E

Pin No. Pin Name I/O Description

1

2

3

4

DEFI

TAI

PDO

VVSS

I

Defect sense signal (DEF) input pin. (Connect to 0V when not used).

I

O

—

Test signal input pin with built-in pull-down resistor. Be sure to connect to0V.

Phase comparator output pin to control external VCO.

GND pin for built-in VCO. Be sure to connect to 0V.

For PLL.

5

6

7

8

9

10

11

12, 13

14

ISET

VVDD

FR

VSS

EFMO

EFMIN

TEST2

CLV+, CLK-

___

V/P

I

—

I

—

Digital system GND. Be sure to connect to 0V.

O

For slice level control.

I

Test signal input pin with built-in pull-down resistor. Be sure to connect to 0V.

O

Disc motor control output. Three level output is possible using command.

Rough servo or phase control automatic selection monitoring output pin. Rough servo

O

Pin to which external resistor adjusting the PD0 output current.

Power supply pin for built-in VCO.

Pin for VCO frequency range adjustment.

EFM signal output pin.

EFM signal input pin.

at H. Phase servo at L.

15

16

17

18

19, 20

21

22

HFL

TES

TOFF

TGL

JP+, JP-

PCK

FSEQ

I

Track detect signal input pin. Schmidt input.

I

Tracking error signal input pin. Schmidt input.

O

Tracking OFF output pin.

O

Tracking gain selection output pin. Gain boost at L.

O

Track jump control signal output pin. Three level output is possible using command.

O

EFM data playback clock monitoring pin 4.3218 MHz when phase is locked in.

Sync signal detection output pin. H when the sync signal which is detected from EFM

O

signal and thesync signal which is internally generated agree.

23

24

25

VDD

SL+

SL-

—

Digital system power supply pin.

O

Moves the sled to outer circumference.

O

Moves the sled to inner circumference.

Pin No. Pin Name I/O Description

43

44

45

46

47

48

49

50

51

XVDD

XOUT

XIN

XVSS

SBSY

EFLG

PW

SFSY

SBCK

—

Crystal oscillator power supply pin.

O

Pin to which external 16.9344 MHz crystal oscillator is connected.

I

Crystal oscillator GND pin. Be sure to connect to 0V.

O

Subcode block sync signal output pin.

O

C1, C2, single and dual correction monitoring pin.

O

Subcode P, Q, R, S, T, U and W output pin.

O

Subcode frame sync signal output pin. Falls down when subcode enters standby.

Subcode read clock input pin. Schmidt input. (Be sure to connected to 0V when not

I

in use.)

52

FSX

Pin outputting the 7.35 kHz sync signal which is generated by dividing frequency of

O

crystal oscillator.

53

54

55

56

57

58

59

60

61

62

63

WRQ

RWC

SQOUT

COIN

___________

CQCK

________

RES

TST11

16M

4.2M

TEST5

______

CS

O

Subcode Q output standby output pin.

I

Read/write control input pin. Schmidt input.

O

Subcode Q output pin.

I

Command input pin from microprocessor.

I

Command input read clock or subcode read input clock from SQOUT pin

I

LC78622 reset input pin. Set this pin to L once when the main power is turned on.

O

Test signal output pin. Use this pin as open (normally L output).

O

16.9344 MHz output pin.

O

4.2336 MHz output pin.

I

Test signal input pin with built-in pull-down resistor. Be sure to connect to 0V.

Chip select signal input pin with built-in pull-down resistor. Be sure to connect to 0V

I

while it is not controlling.

64

TEST1

Test signal input pin without built-in pull-down resistor. Be sure to connect to 0V.

I

26

27

28

29

30

31

32, 33

34

35

36

37

38

39

40

41

42

—

PUIN

—

EMPH

C2F

DOUT

TEST3, TEST4

N.C.

MUTEL

LVDD

LCHO

LVSS

RVSS

RCHO

RVDD

MUTER

—

Not connected.

I

CD pickup inner switch detection.

—

Not connected.

O

De-emphasis monitor output pin. De-emphasis disc is being played back at H.

O

C2 flag output pin.

O

DIGITAL OUT output pin. (EIAJ format).

I

Test signal input pin with built-in pull-down resistor. Be sure to connect to 0V.

—

Not used. Set the pin to open.

O

—

L-channel 1-bit DAC.

O

—

O

R-channel 1-bit DAC. R-channel output pin.

—

O

L-channel mute output pin.

L-channel power supply pin.

L-channel output pin.

L-channel GND. Be sure to connect to 0V.

R-channel GND. Be sure to connect to 0V.

R-channel power supply pin.

R-channel mute output pin.

Note: The same potential must be applied to the respective power supply terminals. (VDD, VVDD, LVDD, RVDD, XVDD)

3433

IC, LC867232A

Pin No. Pin Name I/O Description

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

25

26

27

28

29

30

1

2

3

4

5

6

7

8

9

POP

O-BEAT

O-TUSW

O-CE

O-VRDA

O-DATA

O-CLK

O-PCONT

O-MUTE

O-CKSFT

NC

___________

I-RST

XT1

XT2

VSS1

—

CF1

CF2

VDD1

—

I-KEY0

I-KEY1

I-TRY SW

___________

I-PLAY

I-TUDO

_________________

I-STEREO

I-BATT

________

I-REC

—

I-KOLD

NC

—

I-RMT

O-CD

POP exterenal filter ON/OFF output. ON:H.

O

AM RECORD beat cancel output.

O

TUNER ON/OFF output. ON: H, OFF: L.

O

PLL chip enable output.

O

Sound processor control output 3state.

O

Connected to tuner PLL LC72121(4Pin).

O

Connected to tuner PLL LC72121CL (5Pin).

O

Power supply ON/OFF control. ON: H.

O

Main mute output. Mute: H.

O

5.76 MHz master clock shift output.

O

Not connected.

O

Microprocessor reset input. (L: reset).

I

External 32.768 kHz crystal oscillator is connected to this terminal.

O

GND.

I

External 5.76 MHz ceramic filter is connected to this terminal.

O

Microprocessor power supply 5 V.

Operation key A/D input 1.

I

Operation key A/D input 2.

I

CD tray open/close detection switch signal to A/D input.

I

(CD pick up inside limit switch signal to A/D input PLAY:L).

I

Connected to tuner PLL LC72121 (6Pin) DO.

I

Tuner stereo detection input. ST = L

O

Pull down.

Tape RECORD detection input.

I

HOLD detection input. H: HOLD.

I

Not connected.

Remote control input.

I

CD power supply control output. ON: H, OFF: L.

O

Pin No. Pin Name I/O Description

42

43

44

45

46

47

48

49-55

56

57

58-79

80-82

83-85

86

87

88

89

90

91

92

93

94

95

96

97

98

99

100

AM ST

AM 10K

LW

SW

TIME

OIRT

NC

SEG19-SEG25

VDD2

VSS

SEG26-SEG47

V3-V1

COM0-COM2

NC

WRQ

RWC

VSS3

VDD3

SQOUT

COIN

CQCK

DRF

O-CD-MUTE

O-CLOSE

O-OPEN

NC

CLCKADJ

NC

—

O

Initial setting diode output. AM ST.

O

Initial setting diode output. AM 10K STEP.

O

Initial setting diode output. LW.

O

Initial setting diode output. SW.

Not used.

O

Initial setting diode output. OIRT.

Not connected.

O

LCD segment output.

LCD VDD.

LCD VSS.

O

LCD segment output.

NC. (External power supply for LCD drive is connected to this terminal).

O

LCD common output.

Not connected. (1/3 duty cycle is used for LCD).

O

CD subcode Q output standby.

O

CD read/write control output.

GND.

Microprocessor power supply 5 V.

I

CD subcode Q input.

O

CD control command output.

O

CD clock output.

I

CD RF (DET. RF) level detection output.

O

CD mute output (not used).

O

CD tray close output.

O

CD tray open output.

Not connected.

O

“L” is outputted during the watch setting mode (Not used).

Not connected.

31

32

33

34

35

36

37

38

39

40

41

O-HSP

I-INIT

O-LED.CD

O-LED.AUX

O-LED.TU

O-LED.TA

O-LED.Q

O-LED.ROCK

O-LED.POP

O-LED.JAZZ

FM WIDE

High speed dubbing selector output. ON: L.

O

Initial setting (diode matrix) input.

I

Function. CD LED display control output. ON: H.

O

Function. AUX LED display control output. ON: H.

O

Function. TUNER LED display control output. ON: H.

O

Function. TAPE LED display control output. ON: H.

O

Q-SOUND LED display control output. ON: H.

O

EQ ROCK display (LED) control output. ON: H.

O

EQ POP display (LED) control output. ON: H.

O

EQ JAZZ display (LED) control output. ON: H.

O

Initial setting diode output. FM WIDE.

O

3635

MECHANICAL EXPLODED VIEW 1/1

27

26

59

B

33

B

38

39

HLDR,LCD

10

9

60

11

P.C.B

13

14

12

31

15

18

28

29

35

36

40

30

3ZG-3

34

B

22

B

P.C.B

50

F

B

E

D

C

43

C

45

44

B

D

46

49

B

P.C.B

B

P.C.B

16

37

D

B

41

42

62

47

58

H

17

20

16

19

21

22

21

B

ZZM-2

48

B

47

B

A

51

B

8

HLDR, WOOD

57

SUPPORT

6

23

53

55

7

5

24

61

52

3

4

1

B

54

G

56

10

2

1

aiwa

3837

MECHANICAL PARTS LIST 1/1

REF. NO PART NO. KANRI DESCRIPTION

1 82-NF7-218-010 SPR-T,CASS<U2<S>> 1 8Z-CT4-211-010 SPR-T,CASS<U<S>> 2 8A-CT4-017-010 WINDOW,CASS R 3 8A-CT4-004-010 BOX,CASS R 4 8A-CT4-016-010 WINDOW,CASS L

5 8A-CT4-003-010 BOX,CASS L 6 88-CT4-027-210 KNOB,RTRY TU 7 8A-CT4-014-010 KEY,VOL 8 8A-CT4-019-010 LENS,COVER 9 8A-CT4-015-010 WINDOW,DISP

10 87-B00-010-010 BADGE,AIWA 11 8A-CT4-018-010 LENS,FUNC

12 8A-CT4-007-010 KEY,POWER 13 8A-CT4-013-010 KEY,FUNC 14 8A-CT4-012-010 KEY,CAP

15 8A-CT4-011-010 KEY,MAIN 16 8A-CT4-005-010 KEY,CASS L 17 8A-CT4-010-010 KEY,SURROUND 18 8A-CT4-020-010 LENS,SURROUND 19 8A-CT4-008-010 KEY,EJECT

20 8A-CT4-009-010 KEY,EQ 21 88-CT4-225-010 GEAR,OIL DUMP 22 88-CT4-226-010 HLDR,OIL DUMP 23 8A-CT4-006-010 KEY,CASS R 24 8A-CT4-001-010 CABI,FRONT

25 8A-CT4-206-010 BOSS,FRONT CABI 26 88-CT4-607-010 CONN ASSY,5P 27 88-CT4-606-010 CONN ASSY,4P 28 88-CT4-208-010 SPR-C,BATT B 29 87-A90-193-010 HLDR,CV100 (B)

30 88-CT4-609-010 CONN ASSY,4P 31 8A-CT4-620-010 CONN ASSY,9P DECK 32 8A-CT4-204-010 CHAS,CD L 33 8A-CT4-002-010 PANEL,CD 34 88-905-201-210 FF-CABLE, 5P 1.25

35 88-CT4-623-010 FF-CABLE, 16P 1.0 120MM 36 88-906-121-110 FF-CABLE,6P 37 8A-CT4-205-010 CHAS,CD R 38 8A-CT4-027-010 PANEL,TOP 626<U2<S>> 38 8Z-CT4-041-010 PANEL,TOP ST<U<S>>

NO.

30.5-5.2 S 2.5L<U2<S>>

REF. NO PART NO. KANRI DESCRIPTION

39 86-CT4-616-010 ANT,ROD 40 88-CT4-224-010 HLDR,ANT 41 87-A60-177-010 JACK,AC U W/SW 42 87-A90-086-010 COVER,AC-SOCKET 43 87-CT4-037-010 COVER, BATT

44 8Z-CT4-040-010 LID,BATT<U<S>> 44 8A-CT4-026-010 LID,BATT 626<U2<S>> 45 88-CT4-025-010 PLATE,VOLTAGE 46 88-CT4-207-010 SPR-C,BATT A 47 88-CT4-026-010 CUSH,FOOT

48 8A-CT4-025-010 CABI,REAR 626<U2<S>> 48 8Z-CT4-028-010 CABI,REAR N<U<S>> 49 8A-CT4-202-010 HLDR,FUNC 50 8A-CT4-203-010 HLDR,POWER 51 8Z-CT1-612-010 PT,U

52 8A-CT4-022-010 PANEL,SPKR 53 8A-CT4-021-010 CABI,SPKR FRONT 54 86-CT4-625-010 SPKR,W 120 40HM 10W 6CT-4 55 8Z-CK3-627-010 VIB,PIEZO 4KHZ 56 8Z-CT4-020-010 CABI,REAR SPKR L<U<S>>

56 8A-CT4-031-010 CABI,REAR SPKR L 626<U2<S>> 56 8Z-CT4-021-010 CABI,REAR SPKR R<U<S>> 56 8A-CT4-032-010 CABI,REAR SPKR R 626<U2<S>> 57 86-CT4-627-010 CORD,2PSPKR 58 84-CT4-106-110 HLDR,CORD

59 8Z-CT4-624-010 HLDR,BAR-ANT. 60 88-CT4-218-010 COVER,LED 61 8Z-CT4-044-010 NET,SPKR 61 8A-CT4-023-010 NET,SPKR 62 8A-CT4-201-010 HLDR,EQ

A 87-661-100-410 VFT1+3-16 B 87-751-096-410 VT2+3-10 GLD C 87-753-097-410 VT2+3-12 W/O BLK D 87-753-104-410 VT2+3-30 W/0 BLK E 87-493-100-410 VWWS+3-16 BLK

F 87-067-579-010 BVT2+3-8 W/O SLOT G 87-661-097-410 TAPPING SCREW, VFT1+3-12 H 87-751-098-410 SCREW 3X14

NO.

COLOR NAME TABLE

Basic color symbol Color Basic color symbol Color Basic color symbol Color

B Black C Cream D Orange G Green H Gray L Blue

LT Transparent Blue N Gold P Pink

R Red S Silver ST Titan Silver T Brown V Violet W White

WT Transparent White Y Yellow YT Transparent Yellow

LM Metallic Blue LL Light Blue GT Transparent Green LD Dark Blue DT

Transparent Orange

39

TAPE MECHANISM PARTS LIST 1/1

REF. NO PART NO. KANRI DESCRIPTION

1 8Z-ZM1-254-210 SPR-C,REEL R 2 8Z-ZM1-225-110 GEAR,REEL R 3 8Z-ZM1-253-110 SPR-C,AUTO SENSOR 4 8Z-ZM1-217-110 LEVER,AUTO SENSOR 5 8Z-ZM1-212-110 LEVER,T-UP

6 8Z-ZM1-245-010 SPR-T,AUTO 7 8Z-ZM1-236-010 CLR,SLIP FF/REW 8 8Z-ZM1-252-010 SPR-C,FF/REW 9 8Z-ZM1-230-010 GEAR,SLIP FF/REW A 10 8Z-ZM1-269-010 FELT,FF/REW 2

11 8Z-ZM1-238-110 GEAR,SLIP FF/REW B 2 12 8Z-ZM1-237-010 LEVER,FF/REW 2 13 8Z-ZM1-209-210 LEVER,PAUSE 14 8Z-ZM1-218-110 LEVER,E-LOCK H 15 8Z-ZM1-256-010 SPR-P,PAUSE

16 8Z-ZM1-244-010 SPR-T,T-UP 17 8Z-ZM1-247-210 SPR-T,PINCH 18 8Z-ZM1-261-110 ROLLER ASSY,PINCH 19 8Z-ZM1-221-010 LEVER,PINCH 20 8Z-ZM1-205-210 LEVER,PLAY

21 8Z-ZM1-248-110 SPR-T,BRG 22 87-A90-403-110 HEAD,RPH MS15R 23 84-ZM2-227-310 SPR-C,AZIMUTH 24 8Z-ZM1-216-010 LEVER,AUTO 25 8Z-ZM1-246-010 SPR-T,AUTO 2

26 8Z-ZM2-214-010 GEAR,IDL REW ZZM-2 27 8Z-ZM2-212-010 LEVER,STOP ZZM-2 28 8Z-ZM1-207-010 LEVER,FF 29 8Z-ZM1-206-010 LEVER,REW 30 8Z-ZM1-210-010 LEVER,REC<YR1NF>

30 8Z-ZM1-211-110 LEVER,REC 2<YR2NF,YR3NF> 31 87-A90-404-010 HEAD,EH LE15B<YR1NF> 31 87-A91-533-010 HEAD,EH PH-K380<YR2NF,YR3NF> 32 8Z-ZM2-218-010 LEVER,REC LOCK ZZM-2 33 87-A91-492-010 SW,LEAF MSW18560

NO.

REF. NO PART NO. KANRI DESCRIPTION

34 8Z-ZM1-226-010 GEAR,REEL L 35 8Z-ZM1-241-010 SPR-T,PLAY 36 8Z-ZM1-220-110 LEVER,REC SENSOR 37 8Z-ZM1-249-010 SPR-T,FR 38 8Z-ZM1-242-110 SPR-T,FF/REW

39 8Z-ZM1-229-010 GEAR,CAM 40 8Z-ZM1-232-010 GEAR,IDL FF/REW 41 8Z-ZM1-234-010 FLY-WHL,ZZM-1 42 8Z-ZM1-267-010 SHAFT,CAPSTAN 2 43 8Z-ZM1-228-010 GEAR,SLIP T-UP B

44 8Z-ZM1-265-010 FELT,T-UP 45 8Z-ZM1-227-010 GEAR,SLIP T-UP A 46 8Z-ZM1-251-110 SPR-C,T-UP SLIP 47 8Z-ZM1-243-210 SPR-T,STOP/PAUSE 48 87-A91-532-010 MOT,MS15U2LW1A

49 8Z-ZM1-235-010 PULLEY,MOT 50 8Z-ZM2-216-010 BELT,MAIN M 51 8Z-ZM1-260-010 SPR-P,CASETTE 52 8Z-ZM2-201-010 CHAS ASSY,ZZM-2 53 8Z-ZM1-255-110 SPR-T,E-LOCK

54 8Z-ZM2-219-010 LEVER,E-OPEN ZZM-2 55 8Z-ZM1-214-110 LEVER,LOCK 56 8Z-ZM2-211-010 FLY-WHL,ZZM-2 57 8Z-ZM1-257-110 SPR-C,F/R 58 8Z-ZM2-210-010 LEVER,BRIDGE<YR2NF,YR3NF>

59 80-ZM6-243-010 SH 1.75-3.6-0.5 SLT 60 87-A91-494-010 SW,LEAF MSW17820<YR1NF,YR2NF> 61 8Z-ZM1-241-010 SPR-T,PLAY<YR1NF> 61 8Z-ZM2-217-010 SPR-T,PLAY 2<YR2NF,YR3NF> 62 8Z-ZM2-601-010 CONN ASSY,9P ZZM-2<YR1NF>

63 8Z-ZM1-275-010 W-L,1.47-4-0.25 A 84-ZM2-242-010 S-SCREW,AZ1-2-6.4 B 8Z-ZM2-220-110 V+2.6 ZZM-2

NO.

40

TAPE MECHANISM EXPLODED VIEW 1/1

2

54

4

3

6

5

1

59

46

45

44

53

17

16

14

15

13

19

18

24

27

26

25

28

B

29

61

55

47

17

16

38

TERMINAL,LB1

33

37

14

15

19

21

20

b

13

18

24

22

A

TERMINAL,LB1

23

21

20

54

6

5

28

59

27

25

26

55

29

a

A

22

23

31

30

10

9

57

63

12

11

8

7

43

34

b

1

51

2

a

12

4

3

1

11

10

9

8

7

57

63

40

53

42

39

56

62

48

51

50

49

52

58

47

46

44

45

43

42

41

36

40

33

37

32

34

1

35

38

39

4241

CD MECHANISM EXPLODED VIEW 1/2

CD MECHANISM PARTS LIST 1/2

13

C

17

CUSH-G, MAIN A

3ZG2

REF. NO PART NO. KANRI DESCRIPTION

1 83-ZG3-224-310 HLDR,M2 2 83-ZG3-228-610 CHAS,L6 3 83-ZG3-208-010 PULLEY,MOTOR 4 83-ZG3-213-010 LVR,SW 5 83-ZG3-209-610 CAM,SLIDE

6 83-ZG3-207-010 GEAR,TRAY 7 83-ZG3-204-210 GEAR,C 8 83-ZG3-205-010 GEAR,D 9 83-ZG3-217-010 S-SCREW,GEAR D 10 83-ZG3-220-210 GEAR,PULLEY 2

11 83-ZG3-214-010 BELT,L 12 83-ZG3-229-410 TRAY,CD 2 13 83-ZG3-210-110 HLDR,CHUCK 14 83-ZG3-602-010 RING,MAG 15 83-ZG3-212-010 CAP,DISC

16 83-ZG3-211-010 PLATE,DISC 17 81-ZG1-254-010 S-SCEW,MECH HLDR A 87-067-945-110 VFT2+3-12(F10) B 87-251-071-110 U+2.6-4 C 87-512-074-210 VFT2+2.6-8

5

D 87-352-075-210 VT2+2.6-10

NO.

15

14

16

17

C

CUSH-G, MAIN A

A

B

11

9

10

7

8

4

B

C

6

12

A

D

C

2

D

3

A

P.C.B

B

1

4443

CD MECHANISM EXPLODED VIEW 2/2

12

8

A

11

2

6

A

1

5

P.C.B

CD MECHANISM PARTS LIST 2/2

A

3

4

REF. NO PART NO. KANRI DESCRIPTION

NO.

1 83-ZG2-243-210 CHAS ASSY,SHT 2 83-ZG2-235-010 GEAR,A3 3 83-ZG2-205-210 GEAR,B 4 83-ZG2-236-010 GEAR MOTOR 3 5 83-ZG2-253-010 SHAFT,SLIDE 5

6 87-A90-836-010 PICKUP,KSS-213F 8 83-ZG2-227-210 TURN TABLE,C1 11 83-ZG2-245-410 LEVER,SHUTTER 12 83-ZG2-250-110 SPR-E,SHT 2 A 87-261-032-210 SCREW V+2-3

45

ACCESSORIES/PACKAGE LIST

REF. NO PART NO. KANRI DESCRIPTION

1 8A-CT4-903-010 IB,U(ESF)S 2 8Z-CK4-962-010 RC UNIT,RC-ZAT04 (VS) 3 87-A80-109-010 AC CORD,HK7281 BLK U

NO.

46

REFERENCE NAME LIST ELECTRICAL SECTION

DESCRIPTION REFERENCE NAME

ANT ANTENNAS C- CHIP C-CAP CAP, CHIP C-CAP TN CAP, CHIP TANTALUM C-COIL COIL, CHIP

C-DI DIODE, CHIP C-DIODE DIODE, CHIP C-FET FET, CHIP C-FOTR FILTER, CHIP C-JACK JACK, CHIP

C-LED LED, CHIP C-RES RES, CHIP C-SFR SFR, CHIP C-SLIDE SW SLIDE SWITCH, CHIP C-SW SWITCH, CHIP

C-TR TRANSISTOR, CHIP C-VR VOLUME, CHIP C-ZENER ZENER, CHIP CAP, CER CAP, CERA-SOL CAP, E CAP, ELECT

CAP, M/F CAP, FILM CAP, TC CAP, CERA-SOL CAP, TC-U CAP, CERA-SOL SS CAP, TN CAP, TANTALUM CERA FIL FILTER, CERAMIC

CF FILTER, CERAMIC DL DELAY LINE E/CAP CAP, ELECT FILT FILTER FLTR FILTER

FUSE RES RES, FUSE MOT MOTOR P-DIODE PHOTO DIODE P-SNSR PHOTO SENSER P-TR PHOTO TRANSISTOR

POLY VARI VARIABLE CAPACITOR PPCAP CAP, PP PT POWER TRANSFORMER PTR, RES PTR, MELF RC REMOTE CONTROLLER

RES NF RES, NON-FLAMMABLE RESO RESONATOR SHLD SHIELD SOL SOLENOID SPKR SPEAKER

SW, LVR SWITCH, LEVER SW, RTRY SWITCH, ROTARY SW, SL SWITCH, SLIDE TC CAP CAP, CERA-SOL THMS THERMISTOR

TR TRANSISTOR TRIMMER CAP, TRIMMER TUN-CAP VARIABLE CAPACITOR VIB, CER RESONATOR, CERAMIC VIB, XTAL RESONATOR, CRYSTAL

VR VOLUME ZENER DIODE, ZENER

MECHANICAL SECTION

DESCRIPTION REFERENCE NAME

ADHESHIVE SHEET ADHESHIVE AZ AZIMUTH BAR-ANT BAR-ANTENNA BAT BATTERY BATT BATTERY

BRG BEARING BTN BUTTON CAB CABINET CASS CASSETTE CHAS CHASSIS

CLR COLLAR CONT CONTROL CRSR CURSOR CU CUSHION CUSH CUSHION

DIR DIRECTION DUBB DUBBING FL FRONT LOADING FLY-WHL FLYWHEEL FR FRONT

FUN FUNCTION G-CU G-CUSHION HDL HANDOL HIMERON CLOTH HINGE, BAT HINGE, BATTERY

HLDR HOLDER HT-SINK HEAT SINK IB INSTRUCTION BOOKLET IDLE IDLER IND, L-R INDICATOR, L-R

KEY, CONT KEY, CONTROL KEY, PRGM KEY, PROGRAM KNOB, SL KNOB, SLIDE LBL LABEL LID, BATT LID, BATTERY

LID, CASS LID, CASSETTE LVR LEVER P-SP P-SPRING PANEL, CONT PANEL, CONTROL PANEL, FR PANEL, FRONT

PRGM PROGRAM PULLY, LOAD MO PULLY, LOAD MOTOR RBN RIBBON S- SPECIAL SEG SEGMENT

SH SHEET SHLD-SH SHIELD-SHEET SL SLIDE SP SPRING SP-SCREW SPECIAL-SCREW

SPACER, BAT SPACER, BATTERY SPR SPRING SPR-P P-SPRING SPR-PC-PUSH P-SPRING, C-PUSH T-SP T-SPRING

TERM TERMINAL TRIG TRIGGER TUN TUNING VOL VOLUME W WASHER

WHL WHEEL WORM-WHL WORM-WHEEL

47

931196

2-11, IKENOHATA 1-CHOME, TAITO-KU, TOKYO 110-8710, JAPAN TEL:03 (3827) 3111

Printed in Singapore

Aiwa CA-DW637 US Service Manual

Specifications and Main Features

Frequently Asked Questions

User Manual