Page 1
CA-DW238
LH(S)
CA-DW248
CA-DW258
U(S)
LH(S)
SERVICE MANUAL
COMPACT DISC CARRY
COMPONENT SYSTEM
BASIC TAPE MECHANISM : ZZM-2 APR3NC
BASIC CD MECHANISM : DA11T3C
S/M Code No. 09-012-354-1N1
DATA
Page 2
SPECIFICATIONS
Design and specifications are subject to change without
•
notice
.
-2-
Page 3
ACCESSORIES/PACKAGE LIST-1/1
REF. NO PART NO. KANRI DESCRIPTION
1 8B-CTA-902-010 IB,LH(ESP)FM<238LHSC>
1 8B-CTA-902-010 IB,LH(ESP)FM<258LHSC>
1 8B-CTA-903-010 IB,U(ESF)FM<248USC>
2 8A-CLB-963-010 RC UNIT,RC-AAT25<258LHSC,248USC>
!
3 87-A80-036-010 AC CORD SET ASSY,E W/FLTR VOL<258LHSC>
!
3 87-A80-081-010 AC CORD SET ASSY,EZ BLK<238LHSC>
!
3 87-A80-109-010 AC CORD,HK7281 BLK U<248USC>
!
4 87-A91-017-010 PLUG,CONVERSION JT-0476<258LHSC>
!
4 87-A91-017-010 PLUG,CONVERSION JT-0476<238LHSC>
NO.
-3-
Page 4
PROTECTION OF EYES FROM LASER BEAM DURING SERVICING
This set employs laser. Therefore, be sure to follow carefully the
instructions below when servicing.
WARNING!
WHEN SERVICING, DO NOT APPROACH THE LASER EXIT
WITH THE EYE TOO CLOSELY. IN CASE IT IS NECESSARY TO
CONFIRM LASER BEAM EMISSION. BE SURE TO OBSERVE
FROM A DISTANCE OF MORE THAN 30cm FROM THE
SURFACE OF THE OBJECTIVE LENS ON THE OPTICAL
PICK-UP BLOCK.
Caution: Invisible laser radiation when
open and interlocks defeated avoid exposure to beam.
Advarsel:Usynling laserståling ved åbning,
når sikkerhedsafbrydere er ude af funktion.
Undgå udsættelse for stråling.
VAROITUS!
Laiteen Käyttäminen muulla kuin tässä käyttöohjeessa mainitulla tavalla saattaa altistaa käyt-täjän turvallisuusluokan 1 ylittävälle näkymättömälle lasersäteilylle.
VARNING!
Om apparaten används på annat sätt än vad som specificeras i
denna bruksanvising, kan användaren utsättas för osynling
laserstrålning, som överskrider gränsen för laserklass 1.
CAUTION
Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous
radiation exposure.
ATTENTION
L'utilisation de commandes, réglages ou procédures autres que
ceux spécifiés peut entraîner une dangereuse exposition aux
radiations.
ADVARSEL!
Usynlig laserståling ved åbning, når sikkerhedsafbrydereer ude
af funktion. Undgå udsættelse for stråling.
This Compact Disc player is classified as a CLASS 1 LASER
product.
The CLASS 1 LASER PRODUCT label is located on the rear
exterior.
CLASS 1
KLASSE 1
LUOKAN 1
KLASS 1
LASER PRODUCT
LASER PRODUKT
LASER LAITE
LASER APPARAT
-4-
Page 5
Precaution to replace Optical block
Solder
PICK-UP Assy PWB
(SF-P101NR)
Body or clothes electrostatic potential could ruin
laser diode in the optical block. Be sure ground
body and workbench, and use care the clothes
do not touch the diode.
1) After the connection, remove solder shown in
the right figure.
-5-
Page 6
ELECTRICAL MAIN PARTS LIST-1/4
REF. NO PART NO. KANRI DESCRIPTION
NO.
IC
87-A20-955-010 IC,LA1828
87-A21-090-010 IC,LA4600
87-A21-520-040 C-IC,M61509FP<258LHSC,248USC>
87-A21-443-040 C-IC,M62495AFP<238LHSC>
87-020-828-010 IC,BA3416BL
87-001-440-010 IC,BA15218N
87-A20-446-010 C-IC,LA9241ML
87-A21-319-010 C-IC,LC78622NE
87-A21-093-010 IC,LA6541D
8B-CTA-611-010 C-IC,LC865516A-5T71
87-A20-650-010 IC,RPM6938-V11
TRANSISTOR
89-327-143-080 TR,2SC2714 (0.1W)
87-026-462-080 TR,2SC1740 S(RS 0.3W)
87-026-463-080 TR,2SA933S (0.3W)
87-026-213-080 CHIP-TR,DTC114YK
89-318-154-080 TR,2SC1815 (0.4W)
89-320-011-080 TR,2SC2001 (15W)
87-026-291-080 TR,DTC124XS
89-109-332-380 TR,2SA933RS
87-A30-515-080 TR,2SA1979O/Y
87-A30-287-040 C-TR,DTC114TKA
87-A30-435-040 C-TR,DTC144EK T146
89-112-965-080 TR,2SA1296 (0.75W)
87-A30-226-010 TR,2SB1655E
87-026-464-010 TR,DTC114TS
87-026-291-010 TR,DTC124XS
87-026-463-010 TR,2SA933S,RS
87-026-610-080 TR,KTC3198GR
89-322-405-080 TR,2SC2240GR
DIODE
87-070-345-080 DIODE,IN4148
87-A40-916-040 C-VARI-CAP,HVC202A
87-027-399-080 ZENNER,HZ7A3L
87-A40-466-080 ZENER,MTZJ2.7A
87-A40-648-080 ZENER,MTZJ8.2A
87-027-702-08J ZENNER,HZ6C2L
87-A40-465-090 DIODE,FR202
MAIN C.B
C1 87-010-314-080 C-CAP,S 22P-50V
C2 87-010-316-080 C-CAP,S 33P-50 CH
C3 87-010-314-080 C-CAP,S 22P-50V
C4 87-010-146-080 C-CAP, 2P-50 C CH GRM
C5 87-010-378-080 CAP, ELECT 10-16V
C7 87-012-156-080 C-CAP,S 220P-50 CH
C8 87-010-197-080 CAP, CHIP 0.01 DM
C9 87-010-154-080 C-CAP,S 10P-50 D CH GRM
C10 87-010-197-080 CAP, CHIP 0.01 DM
C11 87-010-151-080 C-CAP,S 7P-50 D CH GRM
C12 87-010-314-080 C-CAP,S 22P-50V
C13 87-010-148-080 CAP,S 4P/50
C14 87-010-196-080 CHIP CAPACITOR,0.1-25
C16 87-010-178-080 CHIP CAP 1000P
C17 87-016-669-080 C-CAP,S 0.1-25 K B
C18 87-010-197-080 CAP, CHIP 0.01 DM
C19 87-016-669-080 C-CAP,S 0.1-25 K B
C20 87-010-400-080 CAP, ELECT 0.47-50V
C21 87-010-403-080 CAP, ELECT 3.3-50V
C22 87-010-197-080 CAP, CHIP 0.01 DM
C24 87-010-784-080 C-CAP,U 0.012-25 B
C25 87-010-784-080 C-CAP,U 0.012-25 B
C26 87-A11-729-080 C-CAP,S 0.47-25 Z F
REF. NO PART NO. KANRI DESCRIPTION
NO.
C27 87-A11-729-080 C-CAP,S 0.47-25 Z F
C28 87-010-992-080 C-CAP,S 0.047-25 B
C29 87-010-992-080 C-CAP,S 0.047-25 B
C30 87-010-248-080 CAP, ELECT 220-10V
C31 87-010-379-080 CAP, ELECT 22-16V
C32 87-010-197-080 CAP, CHIP 0.01 DM
C33 87-010-197-080 CAP, CHIP 0.01 DM
C34 87-010-197-080 CAP, CHIP 0.01 DM
C35 87-010-197-080 CAP, CHIP 0.01 DM
C36 87-010-263-080 CAP, ELECT 100-10V
C38 87-010-322-080 C-CAP,S 100P-50 CH
C39 87-010-197-080 CAP, CHIP 0.01 DM
C56 87-010-151-080 C-CAP,S 7P-50 D CH GRM
C91 87-010-197-080 CAP, CHIP 0.01 DM
C92 87-010-197-080 CAP, CHIP 0.01 DM
C211 87-010-805-080 CAP, S 1-16
C212 87-010-805-080 CAP, S 1-16
C215 87-010-425-080 C-CAP,S 0.22-25 Z F
C216 87-010-425-080 C-CAP,S 0.22-25 Z F
C231 87-015-632-080 C-CAP,0.015-50 B
C232 87-015-632-080 C-CAP,0.015-50 B
C233 87-A10-201-080 C-CAP,S 0.33-16 K B
C234 87-A10-201-080 C-CAP,S 0.33-16 K B
C235 87-015-785-080 CHIP CAPACITOR, 0.1FZ-25Z
C236 87-015-785-080 CHIP CAPACITOR, 0.1FZ-25Z
C237 87-010-374-080 CAP, ELECT 47-10V
C238 87-010-221-080 CAP, ELECT 470-10V
C239 87-010-805-080 CAP, S 1-16<238LHSC>
C239 87-010-197-080 CAP, CHIP 0.01 DM<258LHSC,248USC>
C240 87-010-805-080 CAP, S 1-16<238LHSC>
C240 87-010-197-080 CAP, CHIP 0.01 DM<258LHSC,248USC>
C243 87-010-401-080 CAP, ELECT 1-50V
C244 87-010-401-080 CAP, ELECT 1-50V
C245 87-010-401-080 CAP, ELECT 1-50V
C246 87-010-401-080 CAP, ELECT 1-50V
C247 87-010-401-080 CAP, ELECT 1-50V
C248 87-010-401-080 CAP, ELECT 1-50V
C251 87-010-404-080 CAP, ELECT 4.7-50V
C261 87-010-402-080 CAP, ELECT 2.2-50V
C262 87-010-402-080 CAP, ELECT 2.2-50V
C263 87-010-178-080 CHIP CAP 1000P
C264 87-010-178-080 CHIP CAP 1000P
C266 87-010-545-080 CAP, ELECT 0.22-50V
C267 87-010-545-080 CAP, ELECT 0.22-50V
C271 87-010-235-080 C-CAP,E 470-16 M SME<248USC>
C271 87-010-237-080 CAP, ELECT 1000-16V<EXCEPT 248USC>
C272 87-010-235-080 C-CAP,E 470-16 M SME<248USC>
C272 87-010-237-080 CAP, ELECT 1000-16V<EXCEPT 248USC>
C277 87-010-404-080 CAP, ELECT 4.7-50V
C278 87-010-263-080 CAP, ELECT 100-10V
C279 87-016-628-080 CAP,E 10-25 M SEL
C280 87-010-178-080 CHIP CAP 1000P
C281 87-010-178-080 CHIP CAP 1000P
C285 87-010-178-080 CHIP CAP 1000P
C287 87-010-178-080 CHIP CAP 1000P
C288 87-010-178-080 CHIP CAP 1000P
C292 87-010-404-080 CAP, ELECT 4.7-50V
C293 87-010-404-080 CAP, ELECT 4.7-50V
C299 87-010-196-080 CHIP CAPACITOR,0.1-25
C301 87-010-175-080 CAP 560P
C302 87-010-175-080 CAP 560P
C303 87-010-177-080 C-CAP,S 820P-50 SL
C304 87-010-177-080 C-CAP,S 820P-50 SL
C305 87-010-374-080 CAP, ELECT 47-10V
C306 87-010-374-080 CAP, ELECT 47-10V
C307 87-010-382-080 CAP, ELECT 22-25V
C308 87-010-405-080 CAP, ELECT 10-50V
C309 87-010-404-080 CAP, ELECT 4.7-50V
C310 87-010-404-080 CAP, ELECT 4.7-50V
C311 87-010-248-080 CAP, ELECT 220-10V
-6-
Page 7
ELECTRICAL MAIN PARTS LIST-2/4
REF. NO PART NO. KANRI DESCRIPTION
NO.
C312 87-010-374-080 CAP, ELECT 47-10V
C313 87-015-828-080 C-CAP,0.033 F
C314 87-015-828-080 C-CAP,0.033 F
C315 87-010-401-080 CAP, ELECT 1-50V
C316 87-010-401-080 CAP, ELECT 1-50V
C317 87-010-382-080 CAP, ELECT 22-25V
C320 87-010-405-080 CAP, ELECT 10-50V
C321 87-012-157-080 C-CAP,S 330P-50 CH
C322 87-012-157-080 C-CAP,S 330P-50 CH
C323 87-010-197-080 CAP, CHIP 0.01 DM
C324 87-010-197-080 CAP, CHIP 0.01 DM
C325 87-010-180-080 C-CER 1500P
C326 87-010-180-080 C-CER 1500P
C327 87-010-404-080 CAP, ELECT 4.7-50V
C328 87-010-178-080 C-CAP,S 1000P-50 K B C2012
C329 87-010-182-080 C-CAP,S 2200P-50 B
C330 87-010-213-080 C-CAP,S 0.015-25 K B GRM
C331 87-010-374-080 CAP, ELECT 47-10V
C334 87-012-155-080 C-CAP 180P-50CH
C341 87-012-157-080 C-CAP,S 330P-50 CH
C342 87-012-157-080 C-CAP,S 330P-50 CH
C343 87-012-157-080 C-CAP,S 330P-50 CH
C344 87-010-303-080 C-CAP, 330P-50 J CH
C350 87-010-992-080 C-CAP,S 0.047-25 B
C501 87-010-390-010 CAP,E 3300-25 SME
C506 87-010-404-080 CAP, ELECT 4.7-50V
C507 87-010-401-080 CAP, ELECT 1-50V
C508 87-010-235-080 C-CAP,E 470-16 M SME
C509 87-A11-149-080 CAP,TC U 0.22-50 Z F
C511 87-010-383-080 CAP,E 33-25 M 11L SME
C512 87-010-385-080 CAP, ELECT 220-25V
C520 87-A11-566-080 C-CAP,S 0.01-25 K B
C521 87-A11-566-080 C-CAP,S 0.01-25 K B
C522 87-010-112-810 CAP,E 100-16 M SME
C544 87-010-405-080 CAP, ELECT 10-50V
C762 87-010-198-080 CAP, CHIP 0.022
C765 87-010-196-080 CHIP CAPACITOR,0.1-25
C766 87-010-260-080 CAP, ELECT 47-25V
C767 87-010-384-080 CAP,E 100-25 M 11L SME
CF1 87-A90-128-010 FLTR,AM IF CFAL-455
CF2 87-008-261-08C FRTR,CF SFE10.7MAS5
CF3 87-008-261-08C FRTR,CF SFE10.7MAS5
CN301 8B-CT5-616-010 CONN ASSY,4P 2791 30AWG PH<238LHSC>
CN302 8B-CT5-617-010 CONN ASSY,5P 2791 30AWG PH<238LHSC>
CN501 87-049-919-010 CONN,3P EH V WHT
CN601 87-A60-109-010 CONN,2P V S2M-2W
CN751 8B-CT5-618-010 CONN ASSY,8P 1007 26AWG PH<238LHSC>
CON201 87-A60-202-010 TERMINAL,ANT 4P MSP-54V-02
L2 87-A50-560-010 COIL,FM BPF(ACD)
L3 8A-CD9-660-010 BAR-ANT,MW 2B-ACD(COI)
L4 87-A50-562-010 COIL,FM RF EX(ACD)
L5 87-A50-564-010 COIL,FM OSC EX(ACD)
L6 87-A50-588-010 COIL,AM OSC-ACD(COI)
L7 87-A50-579-010 COIL,AM IFT(ACD)
L8 87-A50-590-010 COIL,FM IFT-ACD(COI)
L9 87-A50-577-010 COIL,FM DET(ACD)
L10 87-005-849-080 COIL,10UH(CECS)
L16 87-A50-588-010 COIL,AM-OSC-ACD(C01)
L330 88-CT6-620-010 REC OSC
L615 87-005-849-080 COIL,10UH(CECS)
PN301 87-A60-110-010 CONN,4P V S2M-4W
PN302 87-A60-111-010 CONN,5P V S2M 5W
PN751 87-099-832-010 CONN,8P S2M-8W
PVC1 87-A91-316-010 TUN-CAP,20P-160P U(TWD)
R761 87-029-019-010 RES, FUSEIBLE 1/2W-2.2
SFR761 87-024-272-010 SFR,10K V RH0632C
SW1 87-A91-548-010 SW,SL-2-3 SK23E01G06
SW301 88-CT6-619-010 BACK SLIDE SW 6P2T SHORTIN
REF. NO PART NO. KANRI DESCRIPTION
CD C.B
C401 87-010-403-080 CAP, ELECT 3.3-50V
C402 87-010-197-080 CAP, CHIP 0.01 DM
C403 87-010-263-080 CAP, ELECT 100-10V
C404 87-010-248-080 CAP, ELECT 220-10V
C405 87-010-197-080 CAP, CHIP 0.01 DM
C406 87-010-374-080 CAP, ELECT 47-10V
C407 87-010-178-080 CHIP CAP 1000P
C408 87-010-198-080 CAP, CHIP 0.022
C409 87-010-248-080 CAP, ELECT 220-10V
C410 87-010-263-080 CAP, ELECT 100-10V
C411 87-A11-693-080 C-CAP,S 0.15-50 M F
C412 87-010-401-080 CAP, ELECT 1-50V
C413 87-016-369-080 C-CAP,S 0.033-25 B K
C414 87-010-401-080 CAP, ELECT 1-50V
C416 87-010-545-080 CAP, ELECT 0.22-50V
C417 87-012-157-080 C-CAP,S 330P-50 CH
C418 87-010-213-080 C-CAP,S 0.015-25 K B GRM
C419 87-A11-608-080 C-CAP,S 0.33-25 K B
C420 87-016-369-080 C-CAP,S 0.033-25 B K
C421 87-A11-693-080 C-CAP,S 0.15-50 M F
C422 87-010-184-080 CHIP CAPACITOR 3300P(K)
C423 87-010-992-080 C-CAP,S 0.047-25 B
C424 87-016-460-080 C-CAP,S 0.22-16 K B
C425 87-010-176-080 C-CAP,S 680P-50 SL
C426 87-A11-608-080 C-CAP,S 0.33-25 K B
C428 87-010-197-080 CAP, CHIP 0.01 DM
C429 87-010-186-080 CAP,CHIP 4700P
C430 87-012-156-080 C-CAP,S 220P-50 CH
C431 87-010-545-080 CAP, ELECT 0.22-50V
C432 87-010-374-080 CAP, ELECT 47-10V
C433 87-010-401-080 CAP, ELECT 1-50V
C434 87-010-184-080 CHIP CAPACITOR 3300P(K)
C435 87-010-197-080 CAP, CHIP 0.01 DM
C436 87-010-374-080 CAP, ELECT 47-10V
C437 87-010-404-080 CAP, ELECT 4.7-50V
C438 87-016-669-080 C-CAP,S 0.1-25 K B
C439 87-010-178-080 CHIP CAP 1000P
C440 87-010-145-080 C-CAP,S 1P-50 CH
C441 87-010-197-080 CAP, CHIP 0.01 DM
C442 87-010-314-080 C-CAP,S 22P-50V
C445 87-010-196-080 CHIP CAPACITOR,0.1-25
C446 87-010-196-080 CHIP CAPACITOR,0.1-25
C447 87-010-196-080 CHIP CAPACITOR,0.1-25
C448 87-010-315-080 C-CAP,S 27P-50 CH
C450 87-010-305-080 C-CAP 470P-50CH
C451 87-012-156-080 C-CAP,S 220P-50 CH
C455 87-010-247-080 CAP, ELECT 100-50V
C457 87-010-312-080 C-CAP,S 15P-50 CH
C458 87-010-312-080 C-CAP,S 15P-50 CH
C459 87-010-263-080 CAP, ELECT 100-10V
C460 87-015-819-080 CAPACITOR,0.01
C461 87-010-197-080 CAP, CHIP 0.01 DM
C462 87-010-248-080 CAP, ELECT 220-10V
C463 87-010-197-080 CAP, CHIP 0.01 DM
C465 87-010-404-080 CAP, ELECT 4.7-50V
C466 87-010-196-080 CHIP CAPACITOR,0.1-25
C467 87-010-263-080 CAP, ELECT 100-10V
C469 87-012-154-080 C-CAP,S 150P-50 CH
C470 87-010-544-080 CAP, ELECT 0.1-50V
C471 87-A11-601-080 C-CAP,S 0.1-25 K B
C472 87-A11-601-080 C-CAP,S 0.1-25 K B
C473 87-A11-601-080 C-CAP,S 0.1-25 K B
C474 87-A11-601-080 C-CAP,S 0.1-25 K B
C475 87-010-197-080 CAP, CHIP 0.01 DM
C476 87-010-236-080 CAP,E 1000-10 SME
C477 87-010-197-080 CAP, CHIP 0.01 DM
C478 87-010-263-080 CAP, ELECT 100-10V
C479 87-010-197-080 CAP, CHIP 0.01 DM
NO.
-7-
Page 8
ELECTRICAL MAIN PARTS LIST-3/4
REF. NO PART NO. KANRI DESCRIPTION
NO.
C480 87-010-221-080 CAP, ELECT 470-10V
C481 87-010-405-080 CAP, ELECT 10-50V
C482 87-010-405-080 CAP, ELECT 10-50V
C489 87-010-196-080 CHIP CAPACITOR,0.1-25
C490 87-010-196-080 CHIP CAPACITOR,0.1-25
C491 87-015-819-080 CAPACITOR,0.01
C492 87-010-221-080 CAP, ELECT 470-10V
C493 87-010-197-080 CAP, CHIP 0.01 DM
C494 87-010-197-080 CAP, CHIP 0.01 DM
C4001 87-010-196-080 CHIP CAPACITOR,0.1-25
C4002 87-010-322-080 C-CAP,S 100P-50 CH
C4003 87-010-322-080 C-CAP,S 100P-50 CH
C4004 87-010-322-080 C-CAP,S 100P-50 CH
C4005 87-010-322-080 C-CAP,S 100P-50 CH
C4006 87-010-322-080 C-CAP,S 100P-50 CH
C4007 87-010-178-080 CHIP CAP 1000P
C4010 87-018-209-08C CAP,TC U 0.1-50 Z F UP 050
C4011 87-010-178-080 CHIP CAP 1000P
C4012 87-010-178-080 CHIP CAP 1000P
C4013 87-010-178-080 CHIP CAP 1000P
CN401 87-A60-424-010 CONN,16P V TOC-B
CNA402 8Z-CT6-631-010 CONN ASSY,6P CD MO
FFC401 8B-CTA-616-010 FF-CABLE,16P 1.0 165MM<238LHSC>
L401 87-005-849-080 COIL,10UH(CECS)
L402 87-005-849-080 COIL,10UH(CECS)
L404 87-003-152-080 COIL, 100UH
L405 87-005-849-080 COIL,10UH(CECS)
L406 87-008-372-080 FLTR,EMI BL 01RN1
SFR430 87-024-437-080 SFR100K,RH063EC
X401 8Z-CD5-633-010 VIB, CER16.93MHZ FCR16.93M2
FRONT C.B
C601 87-010-313-080 CAP, CHIP 18P
C602 87-010-315-080 C-CAP,S 27P-50 CH
C603 87-010-319-080 C-CAP,S 56P-50 CH
C604 87-010-317-080 C-CAP,S 39P-50 CH
C605 87-010-263-080 CAP, ELECT 100-10V
C606 87-010-196-080 CHIP CAPACITOR,0.1-25
C607 87-010-197-080 CAP, CHIP 0.01 DM
C608 87-010-405-080 CAP, ELECT 10-50V
C609 87-010-400-080 CAP, ELECT 0.47-50V
C611 87-010-248-080 CAP, ELECT 220-10V
C613 87-010-196-080 CHIP CAPACITOR,0.1-25
C614 87-010-312-080 C-CAP,S 15P-50 CH
C615 87-010-805-080 CAP, S 1-16
C616 87-010-805-080 CAP, S 1-16
C617 87-010-179-080 CAP,CHIP S B1200P
C618 87-010-263-080 CAP, ELECT 100-10V
C619 87-010-401-080 CAP, ELECT 1-50V
C630 87-A11-566-080 C-CAP,S 0.01-25 K B
C631 87-A11-566-080 C-CAP,S 0.01-25 K B
C632 87-A11-566-080 C-CAP,S 0.01-25 K B
C633 87-A11-566-080 C-CAP,S 0.01-25 K B
C638 87-A11-566-080 C-CAP,S 0.01-25 K B
C639 87-A11-566-080 C-CAP,S 0.01-25 K B
C640 87-A11-566-080 C-CAP,S 0.01-25 K B
C641 87-A11-601-080 C-CAP,S 0.1-25 K B
C642 87-010-197-080 CAP, CHIP 0.01 DM
C830 87-A11-566-080 C-CAP,S 0.01-25 K B
C831 87-A11-566-080 C-CAP,S 0.01-25 K B
C832 87-015-628-080 C-CAP,1800P-50 B
C833 87-010-178-080 CHIP CAP 1000P
REF. NO PART NO. KANRI DESCRIPTION
C834 87-010-404-080 CAP, ELECT 4.7-50V
C835 87-010-544-080 CAP, ELECT 0.1-50V
C836 87-010-178-080 CHIP CAP 1000P
C837 87-010-178-080 CHIP CAP 1000P
C838 87-010-401-080 CAP, ELECT 1-50V
C840 87-010-221-080 CAP, ELECT 470-10V
C841 87-010-401-080 CAP, ELECT 1-50V
C842 87-012-140-080 CAP 470P
C844 87-010-401-080 CAP, ELECT 1-50V
J251 88-CT6-625-010 JACK,MIC
J801 88-CT6-625-010 JACK,MIC
L601 87-003-102-080 COIL, 10UH
L612 87-005-849-080 COIL,10UH(CECS)
L616 87-005-849-080 COIL,10UH(CECS)
L617 87-005-849-080 COIL,10UH(CECS)
L618 87-005-849-080 COIL,10UH(CECS)
L801 87-003-098-080 COIL,2.2UH
LED602 87-A41-050-040 LED,BT-H203D-31 RED
LED603 87-A41-050-040 LED,BT-H203D-31 RED
LED606 87-A41-050-040 LED,BT-H203D-31 RED
LED607 87-A41-050-040 LED,BT-H203D-31 RED
LED608 87-A41-050-040 LED,BT-H203D-31 RED
LED610 87-A41-050-040 LED,BT-H203D-31 RED<258LHSC,248USC>
LED611 87-A41-066-010 LED,FR-12037G RED
SW601 8Z-CT6-636-010 SW,TACT EVQJAC04M
SW602 8Z-CT6-636-010 SW,TACT EVQJAC04M
SW603 8Z-CT6-636-010 SW,TACT EVQJAC04M
SW604 8Z-CT6-636-010 SW,TACT EVQJAC04M
SW605 8Z-CT6-636-010 SW,TACT EVQJAC04M
SW606 8Z-CT6-636-010 SW,TACT EVQJAC04M
SW607 8Z-CT6-636-010 SW,TACT EVQJAC04M
SW608 8Z-CT6-636-010 SW,TACT EVQJAC04M
SW611 8Z-CT6-636-010 SW,TACT EVQJAC04M
SW614 8Z-CT6-636-010 SW,TACT EVQJAC04M
SW615 8Z-CT6-636-010 SW,TACT EVQJAC04M
SW616 8Z-CT6-636-010 SW,TACT EVQJAC04M
SW617 8Z-CT6-636-010 SW,TACT EVQJAC04M
VR801 87-A90-768-010 VR,RTRY 10KAX1 1 H
X601 87-030-273-010 VIB,XTAL 32.768K5PPM
X602 87-A70-070-080 VIB,CER 5.76MHZ CRHF
POWER C.B
C901 87-A10-577-080 CAP,CER 0.022-50 Z YF
C902 87-A10-577-080 CAP,CER 0.022-50 Z YF
C903 87-A10-577-080 CAP,CER 0.022-50 Z YF
C904 87-A10-577-080 CAP,CER 0.022-50 Z YF
CNA901 8Z-CT9-640-010 CONN ASSY,3P EH(POWER)
!
PR901 87-A90-764-080 PROTECTER,1.25A 60V 491<EXCEPT 248USC>
MOTOR C.B
M2 S0-M10-A09-700 MOTOR SLED ASSY
PIN3 S2-369-750-000 PLUG,6P
SW1 S4-S13-A01-600 SW,LEAF
NO.
-8-
Page 9
ELECTRICAL MAIN PARTS LIST-4/4
• Regarding connectors, they are not stocked as they are not the initial order items.
The connectors are available after they are supplied from connector manufacturers upon the order is received.
CHIP RESISTOR PART CODE
Chip Resistor Part Coding
88
A
Resistor Code
Chip resistor
Wattage Type Tolerance
1/16W 1005 5% CJ
1/16W
1/10W
1/8W
1608
2125
3216
5%
5%
5%
Symbol
CJ
CJ
CJ
Figure
Value of resistor
Form
L
Dimensions (mm)
t
W
0.55
Resistor Code
108
118
128
LW t
1.0 0.5 0.35 104
1.6 0.8 0.45
2 1.25 0.45
3.2
1.6
: A
: A
-9-
Page 10
TRANSISTOR ILLUSTRATION-1/1
ECB
2SA1296 2SA1318
ECB
2SC2001
2SA933
2SC1815
2SC2240
KTC3198
ECB
C
B
E
2SC2714
DTC114YK
DTC114TK
DTC144EK
ECB
2SB1655
ECB ECB
DTC114TS
DTC124XS
2SC1740
-10-
Page 11
WIRING-1/2 (MAIN, CD, FRONT)
101112131415161718192021222324
1234567892526272829303132
A
B
C
OPE LED
+
L
R
SPEAKERS
R
D
E
F
+
G
H
I
J
K
L
M
N
O
P
Q
R
S
T
U
-11-
Page 12
SCHEMATIC DIAGRAM-1/5 (MAIN 1/2)
A
A
R763
10k
A
-12-
Page 13
SCHEMATIC DIAGRAM-2/5 (MAIN 2/2)
C092
0.01
9
68k
C091 0.01
C039 0.01
-13-
Page 14
SCHEMATIC DIAGRAM-3/5 (CD)
FFC401
NC
T4
-14-
Page 15
SCHEMATIC DIAGRAM-4/5 (FRONT)
-15-
Page 16
WIRING-2/2 (POWER, MOTOR)
MOTOR C.B
123456789101112131415
A
CNA402
TO CD C.B
+
6
1
M2
PIN3
_
M2
(SLED MOTOR)
SW1
(INSIDE LIMIT SW)
(SPINDLE MOTOR)
SW1
_
M3
M3
B
C
D
E
F
G
H
+
I
J
K
L
M
N
O
P
Q
R
S
-16-
T
U
Page 17
SCHEMATIC DIAGRAM-5/5 (POWER)
238, 258
248
2
CNA901
1
2
CN501
3
O
E
PR
238,258
248
JW
8
238,
6
8
-17-
Page 18
ELECTRICAL ADJUSTMENT-1/1
FRONT C.B MAIN C.B
98
J251
PHONES
0
L330
SFR761
8
CD C.B
< TUNER SECTION >
1. AM Freq. Range Adjustment
L006 ............................................................................. 517kHz
TC003......................................................................... 1750kHz
2. AM Tracking Adjustment
L003 ............................................................................. 600kHz
TC004......................................................................... 1400kHz
3. AM IF Adjustment
Settings: • Test point: IC001 (L1828) 19PIN
• Adjustment location: L007
Method: Adjust L007 so that the output level at 1000kHz
becomes maximum.
4. FM Freq. Range Adjustment
L005 ........................................................................... 87.0MHz
TC001....................................................................... 109.0MHz
5. FM Tracking Adjustment
L004 ........................................................................... 90.0MHz
TC002....................................................................... 108.0MHz
L009
7
1
L006
L005
4
TC3 TC4
19
IC001
2
TC2TC1
L004
2
L003
5
3
L007
6
L008
RPH (DECK1)/PH (DECK2)
6. FM IF Adjustment
Settings: • Test point: IC001 (L1828) 19PIN
• Adjustment location: L008
Method: Adjust L008 so that the output level at 98.0MHz
becomes balanced.
7. FM Balance Adjustment
Settings: • Test point: IC001 (L1828) 19PIN
• Adjustment location: L009
Method: Adjust L009 so that the output level at 98.0MHz
becomes balanced.
< TAPE SECTION >
8. Tape speed Adjustment
Settings: • Test tape: TTA-100
• Test point: J251 (PHONES jack)
• Adjustment location: SFR761
Method: Play back the test tape and adjust SFR761 so that the
frequency counter reads 3000Hz ±5Hz.
9. Head Azimuth Adjustment
Settings: • Test tape: TTA-320
• Test point: J251 (PHONES jack)
• Adjustment location: Azimuth adjustment screw.
Method: Play back the 8kHz signal of the test tape and adjust
screw so that the output becomes maximum.
9
10. Bias frequency Adjustment
L330 ....................................................................56kHz ±2kHz
-18-
Page 19
IC BLOCK DIAGRAM-1/2
IC, M61509
mono. SW
IC, M62495AFP
Control logic
AUTO RESET
-19-
Page 20
IC BLOCK DIAGRAM-2/2
IC, LA6541D
IC, LA1828 IC, BA3416BL
DECK R
DECK R
R OUT
DECK L
DECK L
-20-
L OUT
TAPE SELECT
Page 21
VOLTAGE CHART-1/4
-21-
Page 22
VOLTAGE CHART-2/4
-22-
Page 23
VOLTAGE CHART-3/4
-23-
Page 24
VOLTAGE CHART-4/4
-24-
Page 25
IC DESCRIPTION-1/3 (LA9241ML)-1/2
Pin No. Pin Name I/O Description
1
FIN2
Pin to which external pickup photo diode is connected. RF signal is created by adding with the
I
FIN1 pin signal. FE signal is created by subtracting from the FIN1 pin signal.
10
11
12
13
14
15
16
2
3
4
5
6
7
8
9
FIN1
E
F
TB
TE-
TE
TESI
SCI
TH
TA
TD-
TD
JP
TO
FD
I
Pin to which external pickup photo diode is connected.
Pin to which external pickup photo diode is connected. TE signal is created by subtracting from
I
the F pin signal.
I
Pin to which external pickup photo diode is connected.
I
DC component of the TE signal is input.
I
Pin to which external resistor setting the TE signal gain is connected between the TE pin.
O
TE signal output pin.
TES “Track Error Sense” comparator input pin. TE signal is passed through a band-pass filter
I
then input.
I
Shock detection signal input pin.
I
Tracking gain time constant setting pin.
O
TA amplifier output pin.
Pin to which external tracking phase compensation constants are connected between the TD and
I
VR pins.
I
Tracking phase compensation setting pin.
I
Tracking jump signal (kick pulse) amplitude setting pin.
O
Tracking control signal output pin.
O
Focusing control signal output pin.
17
18
19
20
21
22
23
24
25
26
27
28
29
30, 31
FD-
FA
FA-
FE
FE-
AGND
SP
SPI
SPG
SP-
SPD
SLEQ
SLD
SL-, SL+
Pin to which external focusing phase compensation constants are connected between the FD and
I
FA pins.
Pin to which external focusing phase compensation constants are connected between the FD–
I
and FA– pins.
Pin to which external focusing phase compensation constants are connected between the FA and
I
FE pins.
O
FE signal output pin.
I
Pin to which external FE signal gain setting resistor is connected between the FE pin.
—
Analog signal GND.
O
Signal ended output of the CV+and CV- pin input signal.
I
Spndle amp input.
I
Pin to which external spindle gain setting resistor in 12 cm mode is connected. (Not connected)
Pin to which external spindle phase compensation constants are connected together with SPD
I
pin.
O
Spindle control signal output pin.
I
Pin to which external sled phase compensation constants are connected.
O
Sled control signal output pin.
I
Sled advance signal input pin from microprocessor.
32, 33
34
35
JP-, JP+
TGL
TOFF
I
Tracking jump signal input pin from DSP.
I
Tracking gain control signal input from DSP. Low gain when TGL = H.
I
Tracking off control signal input pin from DSP. Off when TOFF = H.
-25-
Page 26
IC DESCRIPTION-1/3 (LA9241ML)-2/2
Pin No. Pin Name I/O Description
36
TES
O
Pin from which TES signal is output to DSP.
37
38
39, 40
41
42
43
44
45
46
47
48
49
50
51
52
53
HFL
SLOF
CV-, CV+
RFSM
RFS-
SLC
SLI
DGND
FSC
TBC
NC
DEF
CLK
CL
DAT
CE
O
O
O
—
O
—
O
“High Frequency Level” is used to judge whether the main beam position is on top of bit or on
top of mirror.
I
Sled servo off control input pin.
I
CLV error signal input pin from DSP.
RF output pin.
I
RF gain setting and EFM signal 3T compensation constant setting pin together with RFSM pin.
“Slice Level Control” is the output pin which controls the RF signal data slice level by DSP.
I
Input pin which control the data slice level by the DSP.
Digital system GND.
Output pin to which external focus search smoothing capacitor is connected.
I
“Tracking Balance Control” EF balance variable range setting pin.
No connection.
Disc defect detector output pin.
I
Reference clock input pin. 4.23 MHz of the DSP is input.
I
Microprocessor command clock input pin.
I
Microprocessor command data input pin.
I
Microprocessor command chip enable input pin.
54
55
56
57
58
59
60
61
62
63
64
DRF
FSS
VCC2
REFI
VR
LF2
PH1
BH1
LDD
LDS
VCC1
O
“Detect RF” RF level detector output.
I
“Focus Search Select” focus search mode (± search/+ search) select pin. (Not connected)
—
Servo system and digital system Vcc pin.
—
Pin to which external bypass capacitor for reference voltage is connected. (Pull down)
O
Reference voltage output pin.
I
Disc defect detector time constant setting pin. (Pull down)
I
Pin to which external capacitor for RF signal peak holding is connected. (Pull up)
I
Pin to which external capacitor for RF signal bottom holding is connected. (Pull down)
O
APC circuit output pin.
I
APC circuit input pin.
—
RF system Vcc pin.
-26-
Page 27
IC DESCRIPTION-2/3 (LC78622NE)-1/2
Pin No. Pin Name I/O Description
1
DEFI
I
Defect sense signal (DEF) input pin. (Connect to 0V when not used).
2
3
4
5
6
7
8
9
10
11
12, 13
14
15
16
17
18
TAI
PDO
VVSS
ISET
VVDD
FR
VSS
EFMO
EFMIN
TEST2
CLV+, CLV-
___
V/P
HFL
TES
TOFF
TGL
I
O
—
For PLL.
I
—
I
—
Digital system GND. Be sure to connect to 0V.
O
For slice level control.
I
I
Test signal input pin with built-in pull-down resistor. Be sure to connect to 0V.
O
Disc motor control output. Three level output is possible using command.
Rough servo or phase control automatic selection monitoring output pin. Rough servo at H.
O
Phase servo at L.
I
Track detect signal input pin. Schmidt input.
I
Tracking error signal input pin. Schmidt input.
O
Tracking OFF output pin.
O
Tracking gain selection output pin. Gain boost at L.
Test signal input pin with built-in pull-down resistor. Be sure to connect to 0V.
Phase comparator output pin to control external VCO.
GND pin for built-in VCO. Be sure to connect to 0V.
Pin to which external resistor adjusting the PD0 output current. (Pull down)
Power supply pin for built-in VCO.
Pin for VCO frequency range adjustment. (Pull down)
EFM signal output pin.
EFM signal input pin.
19, 20
21
22
23
24
25
26
27
28
29
30
31
32, 33
34
35
JP+, JP-
PCK
FSEQ
VDD
SL+
SL-
PUSW
PUIN
RW
EMPH
C2F
DOUT
TEST3, TEST4
N.C.
MUTEL
O
O
O
—
I/O
I/O
I/O
I/O
I/O
O
O
O
—
O
Track jump control signal output pin. Three level output is possible using command.
EFM data playback clock monitoring pin 4.3218 MHz when phase is locked in. (Not connected)
Sync signal detection output pin. H when the sync signal which is detected from EFM signal and
thesync signal which is internally generated agree. (Not connected)
Digital system power supply pin.
The pin is controlled by the serial data
command from microprocessor. When
General purpose input/output pin 1 to 5.
De-emphasis monitor output pin. De-emphasis disc is being played back at H. (Not connected)
C2 flag output pin. (Not connected)
DIGITAL OUT output pin. (EIAJ format) (Not connected)
Test signal input pin with built-in pull-down resistor. Be sure to connect to 0V.
I
(Connected to GND)
Not used. Set the pin to open.
L-channel mute output pin. (Not connected)
the pin is not used, set the pin to the input
terminal and connect to 0V, or alternately
set the pin to output terminal and leave
the pin open.
36
37
38
39
40
41
LVDD
LCHO
LVSS
RVSS
RCHO
RVDD
—
L-channel 1-bit DAC.
O
—
—
R-channel 1-bit DAC. R-channel output pin.
O
—
L-channel power supply pin.
L-channel output pin.
L-channel GND. Be sure to connect to 0V. (Connected to GND)
R-channel GND. Be sure to connect to 0V. (Connected to GND)
R-channel power supply pin.
-27-
Page 28
IC DESCRIPTION-2/3 (LC78622NE)-2/2
Pin No. Pin Name I/O Description
42
MUTER
O
R-channel 1-bit DAC. R-channel mute output pin. (Not connected)
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
XVDD
XOUT
XIN
XVSS
SBSY
EFLG
PW
SFSY
SBCK
FSX
WRQ
RWC
SQOUT
COIN
___________
CQCK
—
Crystal oscillator power supply pin.
O
Pin to which external 16.9344 MHz crystal oscillator is connected.
I
—
Crystal oscillator GND pin. Be sure to connect to 0V.
O
Subcode block sync signal output pin. (Not connected)
O
C1, C2, single and dual correction monitoring pin. (Not connected)
O
Subcode P, Q, R, S, T, U and W output pin. (Not connected)
Subcode frame sync signal output pin. Falls down when subcode enters standby.
O
(Not connected)
Subcode read clock input pin. Schmidt input. (Be sure to connected to 0V when not in use)
I
(Connected to GND)
Pin outputting the 7.35 kHz sync signal which is generated by dividing frequency of crystal
O
oscillator. (Not connected)
O
Subcode Q output standby output pin.
I
Read/write control input pin. Schmidt input.
O
Subcode Q output pin.
I
Command input pin from microprocessor.
I
Command input read clock or subcode read input clock from SQOUT pin
58
59
60
61
62
RES
TST11
16M
4.2M
TEST5
I
LC78622 reset input pin. Set this pin to L once when the main power is turned on.
O
Test signal output pin. Use this pin as open (normally L output). (Not connected)
O
16.9344 MHz output pin.
O
4.2336 MHz output pin.
Test signal input pin with built-in pull-down resistor. Be sure to connect to 0V.
I
(Connected to GND)
63
______
CS
Chip select signal input pin with built-in pull-down resistor. Be sure to connect to 0V while it is
I
not controlling. (Connected to GND)
64
TEST1
Test signal input pin without built-in pull-down resistor. Be sure to connect to 0V.
I
(Connected to GND)
Note: The same potential must be applied to the respective power supply terminals. (VDD, VVDD, LVDD, RVDD, XVDD)
-28-
Page 29
IC DESCRIPTION-3/3 (LC865516A-5T71)-1/2
Pin No. Pin Name I/O Description
1
SEG E
O
SEG E control.
10
11
12
13
14
15
16
17
18
2
3
4
5
6
7
8
9
SEG F
SEG G
I-W. DECK
I-RES
XT1 (IN)
NC
XT2 (OUT)
VSS
CF1 (IN)
CF2 (OUT)
VDD
I-KEY0
I-KEY1
I-MOTOR
I-CD SW
_________________
HI-DUBB
NC
O
SEG F control.
O
SEG G control.
—
W. DECK control. (Pull up)
I
Micro processor reset input. (Pull down)
I
Connected to an external 32.768 kHz crystal oscillator.
—
Not connected.
O
Connected to an external 32.768 kHz crystal oscillator.
—
GND.
I
Connected to an external 5.76 MHz ceramic filter.
O
Connected to an external 5.76 MHz ceramic filter.
—
Microprocessor power supply (+5V).
I
Key AD input. (AD)
I
Key AD input. (AD)
I
Deck status input. (AD) (Pull up)
I
CD door switch status input. (Pull up)
O
HI-SPEED DUBBING control.
—
Not connected.
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
O-BASS LED
O-Q. SOUND LED
HI-DUBB LED
I-DRF
I-WRQ
NC
I-REM
O-CD ON
O-TU ON
O-P.CONT
NC
O-BEAT
O-MUTE
O-DIGIT
O-SEG RPEAT
O-COIN
I-SQOUT
O
BASS LED ON/OFF control output. (Not connected)
O
Q sound LED ON/OFF control output. (Not connected)
—
HI-SPEED DUBBING LED control.
I
CD RF level detection input.
I
CD subcode Q standby input.
—
Not connected.
—
Remote control input. (Pull up)
O
CD power control output.
O
TU power control output.
O
The main power supply control output.
—
Not connected.
O
Beat control.
O
Main mute output.
O
7-segment LED power supply control output.
O
REPEAT LED ON/OFF control output.
O
CD command output.
I
CD subcode Q input.
36
37
38
39
40
41
O-CQCK
O-RWC
O-DATA
O-CD LED
O-TU LED
O-TA LED
O
CD command/CLK for subcode.
O
CD read/write control output.
O
Data output to M62349FP.
O
LED ON/OFF control output for the CD function.
O
LED ON/OFF control output for the TU function.
O
LED ON/OFF control output for the TA function. (Not connected)
-29-
Page 30
IC DESCRIPTION-3/3 (LC865516A-5T71)-2/2
Pin No. Pin Name I/O Description
42
43
44
45
46
47
NC
______________
SEG DP
____________
SEG A
____________
SEG B
____________
SEG C
____________
SEG D
—
O
O
O
O
O
Not connected.
SEG DP control.
SEG A control.
SEG B control.
SEG C control.
SEG D control.
48
NC
—
Not connected.
-30-
Page 31
MECHANICAL EXPLODED VIEW-1/1
18
40
19
42
45
L
A
CHAS,TU
15
H
23
44
D
20
F
C
PLATE,PT
D
22
ANT
50
51
D
53
PWB
CUSH,FOOT
PLATE,ANT
PWB
39
36
37
D
35
34
33
32
31
30
29
6
28
7
11
D
27
HLDR,LED
9
12
PWB
8
HT-SINK
13
14
41
E
B
F
ZZM-2
38
24
21
10
E
43
25
B
D
PWB
D
I
A
46
47
A
C
49
48
G
J
J
K
G
G
26
54
E
E
52
E
A
C
5
55
A
1
2
3
4
5
16
17
A
A
CABI,FR SPKR
NET,SPKR
44
-31-
Page 32
MECHANICAL PARTS LIST-1/1
REF. NO PART NO. KANRI DESCRIPTION
NO.
1 8B-CTA-007-010 WINDOW,CASS L
2 8B-CTA-004-010 BOX,CASS L
3 8B-CTA-008-010 WINDOW,CASS R
4 8B-CTA-005-010 BOX,CASS R
5 8B-CTA-206-010 SPR-T,CASS
6 8B-CTA-045-010 WINDOW,DISP LH<5LHSC>
6 8B-CTB-006-010 WINDOW,DISP LH L<3LHSC>
6 8B-CTA-006-010 WINDOW,DISP U<4USC>
7 8B-CTB-001-010 CABI,FR LH L<3LHSC>
7 8B-CTA-001-010 CABI,FR U<5LHSC,4USC>
8 8B-CTA-013-010 BTN,FUNC
9 8B-CTA-015-010 KNOB,SL BAND
10 8B-CTA-017-010 BTN,EQ
11 8B-CTA-018-010 LENS,FUNC
12 8B-CTA-019-010 LENS,REPEAT
13 8B-CTA-020-010 LENS,EQ<5LHSC,4USC>
14 87-063-165-010 OIL-DMPR 150
15 87-A90-086-010 COVER,AC-SOCKET
16 8B-CTA-011-010 KEY,CASS L
17 8B-CTA-012-010 KEY,CASS R
18 8B-CT5-208-010 SPR-P,REC
19 8A-CT9-215-010 SPR-P,REC A
19 8B-CTA-207-010 SPR-P,REC B
20 88-CD6-661-010 HLDR,BAR ANT.
21 86-CT9-205-110 HLDR,REC
22 88-CT6-632-010 TERMINAL,ASSY MECHA 1P
23 8B-CTA-203-010 GEAR,TU
24 88-CH6-220-010 CUSHION,CD A
25 8Z-CT9-064-010 PANEL CD<5LHSC,4USC>
25 8B-CTA-031-010 PANEL,CD M<3LHSC>
26 86-CT9-212-010 SPR-C,BATT LINK
27 8B-CTA-202-010 HLDR,LED REPEAT
28 8B-CTA-201-010 HLDR,LED FUNC
29 8B-CTA-014-010 KNOB,RTRY MIC
30 8Z-CT6-214-010 RING,CHUCK
31 8Z-CT6-213-010 BASE,CHUCK
32 87-036-368-010 MAGNET
33 86-CT9-222-010 PLATE,MAGNET
34 86-CT9-217-010 HLDR,CHUCK A(S)
35 8B-CTA-009-010 LID,CD
REF. NO PART NO. KANRI DESCRIPTION
36 8B-CTA-021-010 POINTER,TU
37 8B-CTA-208-010 HLDR,POINTER
38 8B-CTA-010-010 CHAS,CD
39 87-036-389-010 SW,PUSH LOCK
40 8B-CTA-205-010 SPR-T,CD
41 M8-ZZK-E90-070 DA11T3C
42 8B-CTA-016-010 KNOB,RTRY TU
43 87-063-164-010 OIL-DMPR 80
44 8Z-CT6-647-010 SPKR,12 3.2OHM<5LHSC>
44 8Z-CT9-631-010 SPKR,12 7.0OHM<4USC>
44 8B-CTA-615-010 SPKR,5' 3.2OHM 5W<3LHSC>
45 8B-CTA-022-010 HANDL,ARM
46 8B-CTA-023-010 HANDL,GRIP
47 8B-CTA-003-010 LID,BATT
48 87-A92-048-010 ANT,ROD 5SEC
49 8B-CTB-004-010 CABI,REAR LH<3LHSC>
49 8B-CTA-036-010 CABI,REAR LH<5LHSC>
49 8B-CTA-002-010 CABI,REAR U (7 OHM N)<4USC>
!
50 87-A60-178-010 JACK,AC E W/SW<5LHSC,3LHSC>
!
50 87-A60-177-010 JACK,AC U W/SW<4USC>
!
51 88-CT6-631-010 POWER TRANS,EI-57/25<5LHSC,3LHSC>
!
51 88-CT7-629-010 PT,U<4USC>
52 8Z-CT6-646-010 CORD ASSY,SPEAKER
53 86-CT9-213-010 SPR-C,BATT(-)
54 8B-CTA-029-010 HLDR,CORD SPKR
55 8B-CTA-025-010 CABI,REAR SPKR L
55 8B-CTA-026-010 CABI,REAR SPKR R
A 87-751-097-410 SCREW 3X12
B 81-CD5-204-010 SCREW CD
C 87-751-095-410 VT2+3-8 W/O
D 87-571-095-410 VIT+3-8
E 87-651-100-410 VT1+3-16
F 87-651-075-210 VT1+2.6-10
G 87-651-104-410 VT1+3-30
H 87-261-072-410 V+2.6-5<3LHSC>
J 87-721-097-410 QT2+3-12 GLD
I 8A-CDA-222-010 S-SCREW,CASS+2.6-4
K 87-265-097-410 V+3-12 NI
L 87-751-096-410 VT2+3-10 GLD
NO.
-32-
Page 33
COLOR NAME TABLE
Basic color symbol Color Basic color symbol Color Basic color symbol Color
B Black C Cream D Orange
G Green H Gray L Blue
LT Transparent Blue N Gold P Pink
R Red S Silver ST Titan Silver
T Brown V Violet W White
WT Transparent White Y Yellow YT Transparent Yellow
LM Metallic Blue LL Light Blue GT Transparent Green
LD Dark Blue DT Transparent Orange GM Metallic Green
YM Metallic Yellow DM Metallic Orange PT Transparent Pink
LA Aqua Blue GL Light Green
-33-
Page 34
TAPE MECHANISM EXPLODED VIEW-1/1 (ZZM-2 APR3NC)
2
54
4
3
6
5
1
59
46
45
44
53
17
16
14
15
13
19
18
24
27
26
25
28
55
29
61
17
B
47
16
38
TERMINAL,LB1
33
37
14
15
19
21
20
b
13
18
24
22
A
TERMINAL,LB1
23
21
20
54
6
5
28
59
27
25
26
55
29
a
A
22
23
31
30
10
9
57
63
12
11
8
7
43
34
b
1
51
2
a
12
4
3
1
11
10
9
8
7
57
63
40
53
42
39
56
62
48
51
50
49
52
58
47
46
44
45
43
42
41
36
40
33
37
32
34
1
35
38
39
-34-
Page 35
TAPE MECHANISM PARTS LIST-1/1 (ZZM-2 APR3NC)
REF. NO PART NO. KANRI DESCRIPTION
NO.
1 8Z-ZM1-254-310 SPR-C,REEL R
2 8Z-ZM1-225-110 GEAR,REEL R
3 8Z-ZM1-253-210 SPR-C,AUTO SENSOR
4 8Z-ZM1-217-110 LEVER,AUTO SENSOR
5 8Z-ZM1-212-210 LEVER,T-UP
6 8Z-ZM1-245-310 SPR-T,AUTO
7 8Z-ZM1-236-010 CLR,SLIP FF/REW
8 8Z-ZM1-252-110 SPR-C,FF/REW
9 8Z-ZM2-213-010 GEAR,SLIP FR A ZZM-2
10 8Z-ZM1-269-010 FELT,FF/REW 2
11 8Z-ZM1-238-110 GEAR,SLIP FF/REW B 2
12 8Z-ZM1-237-110 LEVER,FF/REW 2
13 8Z-ZM1-209-510 LEVER,PAUSE
14 8Z-ZM1-218-210 LEVER,E-LOCK H
15 8Z-ZM1-256-010 SPR-P,PAUSE
16 8Z-ZM1-244-110 SPR-T,T-UP
17 8Z-ZM1-247-310 SPR-T,PINCH
18 8Z-ZM1-261-110 ROLLER ASSY,PINCH
19 8Z-ZM1-221-210 LEVER,PINCH
20 8Z-ZM1-205-310 LEVER,PLAY
21 8Z-ZM1-248-210 SPR-T,BRG
22 87-A90-403-110 HEAD,RPH MS15R
23 84-ZM2-227-310 SPR-C,AZIMUTH
24 8Z-ZM1-216-110 LEVER,AUTO
25 8Z-ZM1-246-110 SPR-T,AUTO 2
26 8Z-ZM2-214-110 GEAR,IDL REW ZZM-2
27 8Z-ZM2-212-010 LEVER,STOP ZZM-2
28 8Z-ZM1-207-010 LEVER,FF
29 8Z-ZM1-206-010 LEVER,REW
30 8Z-ZM1-210-010 LEVER,REC<YR1NF>
30 8Z-ZM1-211-210 LEVER,REC 2<YR2NF,YR3NF>
31 87-A90-404-010 HEAD,EH LE15B<YR1NF>
31 87-A91-533-010 HEAD,EH PH-K380<YR2NF,YR3NF>
32 8Z-ZM2-218-010 LEVER,REC LOCK ZZM-2
33 87-A91-492-010 SW,LEAF MSW18560
REF. NO PART NO. KANRI DESCRIPTION
NO.
34 8Z-ZM1-226-010 GEAR,REEL L
35 8Z-ZM1-241-210 SPR-T,PLAY
36 8Z-ZM1-220-110 LEVER,REC SENSOR
37 8Z-ZM1-249-210 SPR-T,FR
38 8Z-ZM1-242-310 SPR-T,FF/REW
39 8Z-ZM3-244-110 GEAR,CAM TD20
40 8Z-ZM1-232-010 GEAR,IDL FF/REW
41 8Z-ZM3-228-110 FLY-WHL,M3
42 8Z-ZM1-267-110 SHAFT,CAPSTAN 2
43 8Z-ZM1-228-010 GEAR,SLIP T-UP B
44 8Z-ZM1-265-010 FELT,T-UP
45 8Z-ZM1-227-010 GEAR,SLIP T-UP A
46 8Z-ZM1-251-210 SPR-C,T-UP SLIP
47 8Z-ZM1-243-310 SPR-T,STOP/PAUSE
48 87-A91-532-010 MOT,MS15U2LW1A
49 8Z-ZM1-235-010 PULLEY,MOT
50 8Z-ZM2-216-010 BELT,MAIN M
51 8Z-ZM1-260-010 SPR-P,CASETTE
52 8Z-ZM2-201-510 CHAS ASSY,ZZM-2
53 8Z-ZM1-255-310 SPR-T,E-LOCK
54 8Z-ZM2-219-010 LEVER,E-OPEN ZZM-2
55 8Z-ZM1-214-310 LEVER,LOCK
56 8Z-ZM2-211-210 FLY-WHL,ZZM-2
57 8Z-ZM1-257-110 SPR-C,F/R
58 8Z-ZM2-210-010 LEVER,BRIDGE<YR2NF,YR3NF>
59 87-B10-301-010 W-L,1.63-3.2-0.5 SLIT
60 87-A91-494-010 SW,LEAF MSW17820<YR1NF,YR2NF>
61 8Z-ZM1-241-010 SPR-T,PLAY<YR1NF>
61 8Z-ZM2-217-010 SPR-T,PLAY 2<YR2NF,YR3NF>
62 8Z-ZM2-601-010 CONN ASSY,9P ZZM-2<YR1NF>
63 8Z-ZM1-275-010 W-L,1.47-4-0.25<YR1NF>
A 84-ZM2-242-010 S-SCREW,AZ1-2-6.4
B 8Z-ZM2-220-110 V+2.6 ZZM-2
-35-
Page 36
CD MECHANISM EXPLODED VIEW-1/1 (DA11T3C)
1
SW1
A
2
3
4
MOTOR C.B
M2
PIN 3
-36-
Page 37
CD MECHANISM PARTS LIST-1/1 (DA11T3C)
REF. NO PART NO. KANRI DESCRIPTION
1 M8-ZZK-E90-070 DA11T3C
2 S2-121-A28-400 COVER GEAR
3 S2-511-A21-000 GEAR MIDDLE
4 S2-511-A21-100 GEAR,DRIVE
A S1-PN2-03R-OSE SCR PAN PCS 2-3
NO.
-37-
Page 38
2–11, IKENOHATA 1–CHOME, TAITO-KU, TOKYO 110-8710, JAPAN TEL:03 (3827) 3111
H251701
Printed in Singapore
Loading...