Page 1
CA-DW247
U(S)
CA-DW257
LH(S)
SERVICE MANUAL
COMPACT DISC CARRY
COMPONENT SYSTEM
This Service Manual is the “Revision Publishing” and replaces “Simple Manual”
CA-DW247 U<S>,U2<S> (S/M Code No.09-003-339-4T1)
CA-DW257 LH<S> (S/M Code No.09-003-339-4T2)
BASIC TAPE MECHANISM : ZZM-2 YPR3NF
BASIC CD MECHANISM : DA11T3C
.
S/M Code No. 09-003-339-4R1
REVISION
DATA
Page 2
SPECIFICATIONS
Design and specifications are subject to change without
•
notice
.
ACCESSORIES/PACKAGE LIST
REF. NO PART NO. KANRI DESCRIPTION
1 8A-CT9-902-010 IB,LH(ESP)FM<257 LH<S>>
1 8A-CT9-903-010 IB,U(ESF)FM<EXCEPT 257 LH<S>>
!
2 87-A90-312-010 PLUG,CONVERSION WTN-1157R1
!
3 87-A80-036-010 AC CORD SET ASSY,E W/FLTR VOL
!
3 87-A80-109-010 AC CORD,HK7281 BLK U
4 8Z-CDK-962-010 RC UNIT,RC-ZAT02(VS)
NO.
<257 LH<S>>
<257 LH<S>>
<EXCEPT 257 LH<S>>
2
Page 3
PROTECTION OF EYES FROM LASER BEAM DURING SERVICING
CLASS 1
KLASSE 1
LUOKAN 1
KLASS 1
LASER PRODUCT
LASER PRODUKT
LASER LAITE
LASER APPARAT
This set employs laser. Therefore, be sure to follow carefully the
instructions below when servicing.
WARNING!
WHEN SERVICING, DO NOT APPROACH THE LASER EXIT
WITH THE EYE TOO CLOSELY. IN CASE IT IS NECESSARY TO
CONFIRM LASER BEAM EMISSION. BE SURE TO OBSERVE
FROM A DISTANCE OF MORE THAN 30cm FROM THE
SURFACE OF THE OBJECTIVE LENS ON THE OPTICAL
PICK-UP BLOCK.
Caution: Invisible laser radiation when
open and interlocks defeated avoid exposure to beam.
Advarsel:Usynling laserståling ved åbning,
når sikkerhedsafbrydere er ude af funktion.
Undgå udsættelse for stråling.
VAROITUS!
Laiteen Käyttäminen muulla kuin tässä käyttöohjeessa mainitulla tavalla saattaa altistaa käyt-täjän turvallisuusluokan 1 ylittävälle näkymättömälle lasersäteilylle.
CAUTION
Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous
radiation exposure.
ATTENTION
L'utilisation de commandes, réglages ou procédures autres que
ceux spécifiés peut entraîner une dangereuse exposition aux
radiations.
ADVARSEL!
Usynlig laserståling ved åbning, når sikkerhedsafbrydereer ude
af funktion. Undgå udsættelse for stråling.
This Compact Disc player is classified as a CLASS 1 LASER
product.
The CLASS 1 LASER PRODUCT label is located on the rear
exterior.
VARNING!
Om apparaten används på annat sätt än vad som specificeras i
denna bruksanvising, kan användaren utsättas för osynling
laserstrålning, som överskrider gränsen för laserklass 1.
Precaution to replace Optical block
(SF-P101NR)
Body or clothes electrostatic potential could ruin
laser diode in the optical block. Be sure ground
body and workbench, and use care the clothes
do not touch the diode.
1) After the connection, remove solder shown in
the right figure.
PICK-UP Assy P.C.B
Solder
3
Page 4
ELECTRICAL MAIN PARTS LIST
REF. NO PART NO. KANRI DESCRIPTION
IC
87-A20-955-010 IC,LA1828
87-A21-090-010 IC,LA4600
87-A21-520-040 C-IC,M61509FP
87-020-828-010 IC,BA3416BL
87-001-440-010 IC,BA15218N
87-A20-446-010 C-IC,LA9241ML
87-A20-459-010 C-IC,LC78622ED
87-A21-093-010 IC,LA6541D
8A-CH4-661-010 C-IC,LC867132V-5P07
87-A20-914-010 IC,SPS-442-1-F
TRANSISTOR
89-327-143-080 TR,2SC2714 (0.1W)
87-026-447-080 TR,2SC1740S R
87-026-463-080 TR,2SA933S (0.3W)
87-026-213-080 CHIP-TR,DTC114YK
89-318-154-080 TR,2SC1815 (0.4W)
89-320-011-080 TR,2SC2001 (15W)
87-026-462-080 TR,2SC1740 S RS (0.3W)
87-026-291-080 TR,DTC124XS
89-109-332-380 TR,2SA933RS
89-113-187-080 TR,2SA1318TU
87-A30-287-040 CHIP TR DTC114TKA T146
87-A30-435-040 CHIP TR DTC144EKA T146
89-112-965-080 TR,2SA1296 (0.75W)
87-A30-226-010 TR,2SB1655E
87-026-291-010 TR,DTC124XS
87-026-463-010 TR,2SA933S,RS
87-026-464-010 TR,DTC114TS
87-026-610-080 TR,KTC3198GR
89-322-405-080 TR,2SC2240GR
DIODE
87-020-465-080 DIODE,1SS133 (110MA)
87-A40-128-080 C-VARI-CAP,HVU202A
87-027-703-080 ZENER,HZ7A1L<257 LH<S>>
87-027-399-080 ZENER,HZ7A3L<EXCEPT 257 LH<S>>
87-A40-466-080 ZENER,MTZJ2.7A
87-070-345-080 DIODE,IN4148
87-A40-648-080 ZENER,MTZJ8.2A
87-027-702-080 ZENER,HZ6C2L
84-RM1-695-010 DIODE,1N4148
87-A40-465-010 DIODE,FR202
MAIN C.B
C1 87-010-314-080 C-CAP,S 22P-50V
C2 87-010-316-080 C-CAP,S 33P-50 CH
C3 87-010-314-080 C-CAP,S 22P-50V
C4 87-010-148-080 CHIP CAP S 4P/50V(C) CH
C5 87-010-378-080 CAP, ELECT 10-16V
C7 87-012-156-080 C-CAP,S 220P-50 CH
C8 87-010-197-080 CAP, CHIP 0.01 DM
C9 87-010-311-080 CAP 12P
C10 87-010-197-080 CAP, CHIP 0.01 DM
C11 87-010-152-080 CHIP.CAP,S 8P/50V(D)CH
C12 87-010-314-080 C-CAP,S 22P-50V
C13 87-010-148-080 CHIP CAP S 4P/50V(C) CH
C14 87-016-669-080 C-CAP,S 0.1-25 K B
C15 87-016-669-080 C-CAP,S 0.1-25 K B
C16 87-010-178-080 CHIP CAP 1000P
C17 87-016-669-080 C-CAP,S 0.1-25 K B
C18 87-010-197-080 CAP, CHIP 0.01 DM
C19 87-016-669-080 C-CAP,S 0.1-25 K B
C20 87-010-400-080 CAP, ELECT 0.47-50V
C21 87-010-403-080 CAP, ELECT 3.3-50V
NO.
C22 87-010-197-080 CAP, CHIP 0.01 DM
C24 87-010-426-080 CHIP.CAP,S 0.012U/50V(Z)
C25 87-010-426-080 CHIP.CAP,S 0.012U/50V(Z)
C26 87-A11-729-080 CHIP CA 0.47UF/25V(Z)F
C27 87-A11-729-080 CHIP CA 0.47UF/25V(Z)F
C28 87-010-992-080 C-CAP,S 0.047-25 B
C29 87-010-992-080 C-CAP,S 0.047-25 B
C30 87-010-248-080 CAP, ELECT 220-10V
C31 87-010-379-080 CAP, ELECT 22-16V
C32 87-010-197-080 CAP, CHIP 0.01 DM
C33 87-010-197-080 CAP, CHIP 0.01 DM
C34 87-010-197-080 CAP, CHIP 0.01 DM
C35 87-010-197-080 CAP, CHIP 0.01 DM
C36 87-010-263-080 CAP, ELECT 100-10V
C38 87-010-322-080 C-CAP,S 100P-50 CH
C39 87-010-197-080 CAP, CHIP 0.01 DM
C39 87-010-197-080 CAP, CHIP 0.01 DM
C51 87-010-197-080 CAP, CHIP 0.01 DM
C56 87-010-148-080 CHIP CAP S 4P/50V(C) CH
C91 87-010-197-080 CAP, CHIP 0.01 DM
C92 87-010-197-080 CAP, CHIP 0.01 DM
C212 87-010-805-080 CHIP.CAP,S 1U-16V(Z)F
C212 87-010-805-080 CHIP.CAP,S 1U-16V(Z)F
C215 87-016-460-080 C-CAP,S 0.22-16 B
C216 87-016-460-080 C-CAP,S 0.22-16 B
C231 87-015-632-080 C-CAP,0.015-50 B
C232 87-015-632-080 C-CAP,0.015-50 B
C233 87-A10-201-080 C-CAP,S0.33-16 KB
C234 87-A10-201-080 C-CAP,S0.33-16 KB
C235 87-015-785-080 CHIP CAPACITOR, 0.1FZ-25Z
C236 87-015-785-080 CHIP CAPACITOR, 0.1FZ-25Z
C237 87-010-221-080 CAP, ELECT 470-10V
C238 87-010-248-080 CAP, ELECT 220-10V
C239 87-010-197-080 CAP, CHIP 0.01 DM
C240 87-010-197-080 CAP, CHIP 0.01 DM
C241 87-010-401-080 CAP, ELECT 1-50V
C242 87-010-401-080 CAP, ELECT 1-50V
C243 87-010-401-080 CAP, ELECT 1-50V
C244 87-010-401-080 CAP, ELECT 1-50V
C245 87-010-401-080 CAP, ELECT 1-50V
C246 87-010-401-080 CAP, ELECT 1-50V
C247 87-010-401-080 CAP, ELECT 1-50V
C248 87-010-401-080 CAP, ELECT 1-50V
C251 87-010-404-080 CAP, ELECT 4.7-50V
C261 87-010-402-080 CAP, ELECT 2.2-50V
C262 87-010-402-080 CAP, ELECT 2.2-50V
C263 87-010-178-080 CHIP CAP 1000P
C265 87-010-404-080 CAP, ELECT 4.7-50V
C266 87-010-545-080 CAP, ELECT 0.22-50V
C267 87-010-545-080 CAP, ELECT 0.22-50V
C271 87-010-237-080 CAP, ELECT 1000-16V<257 LH<S>>
C271 87-010-221-080 CAP, ELECT 470-10V<EXCEPT 257 LH
C272 87-010-237-080 CAP, ELECT 1000-16V<257 LH<S>>
C272 87-010-221-080 CAP, ELECT 470-10V<EXCEPT 257 LH
C277 87-010-404-080 CAP, ELECT 4.7-50V
C278 87-010-263-080 CAP, ELECT 100-10V
C279 87-010-263-080 CAP, ELECT 100-10V
C280 87-010-178-080 CHIP CAP 1000P
C281 87-010-178-080 CHIP CAP 1000P
C285 87-010-178-080 CHIP CAP 1000P
C287 87-010-178-080 CHIP CAP 1000P
C288 87-010-178-080 CHIP CAP 1000P
C291 87-010-404-080 CAP, ELECT 4.7-50V
C293 87-010-404-080 CAP, ELECT 4.7-50V
C301 87-010-306-080 CHIP CAP 560P/50V (J) CH
C302 87-010-306-080 CHIP CAP 560P/50V (J) CH
C303 87-010-177-080 C-CAP,S 820P-50 SL
C304 87-010-177-080 C-CAP,S 820P-50 SL
REF. NO PART NO. KANRI DESCRIPTION
NO.
<S>>
<S>>
4
Page 5
REF. NO PART NO. KANRI DESCRIPTION
NO.
C305 87-010-260-080 CAP, ELECT 47-25V
C306 87-010-260-080 CAP, ELECT 47-25V
C307 87-010-382-080 CAP, ELECT 22-25V
C308 87-010-405-080 CAP, ELECT 10-50V
C309 87-010-545-080 CAP, ELECT 0.22-50V
C310 87-010-545-080 CAP, ELECT 0.22-50V
C311 87-010-248-080 CAP, ELECT 220-10V
C312 87-010-260-080 CAP, ELECT 47-25V
C313 87-015-828-080 C-CAP,0.033 F
C314 87-015-828-080 C-CAP,0.033 F
C315 87-010-401-080 CAP, ELECT 1-50V
C316 87-010-401-080 CAP, ELECT 1-50V
C317 87-010-382-080 CAP, ELECT 22-25V
C318 87-010-382-080 CAP, ELECT 22-25V
C319 87-010-405-080 CAP, ELECT 10-50V
C320 87-010-405-080 CAP, ELECT 10-50V
C321 87-012-157-080 C-CAP,S 330P-50 CH
C322 87-012-157-080 C-CAP,S 330P-50 CH
C323 87-010-197-080 CAP, CHIP 0.01 DM
C324 87-010-197-080 CAP, CHIP 0.01 DM
C325 87-010-180-080 C-CER 1500P
C326 87-010-180-080 C-CER 1500P
C327 87-010-404-080 CAP, ELECT 4.7-50V
C328 87-010-178-080 CHIP CAP 1000P
C329 87-018-132-080 CAP,CER 2200P-16V
C330 87-010-213-080 C-CAP,S 0.015-50 B
C331 87-010-260-080 CAP, ELECT 47-25V
C332 87-A10-321-080 MALAY CAP 0.0012UF/50V(K)
C334 87-012-155-080 C-CAP 180P-50CH
C335 87-010-178-080 CHIP CAP 1000P
C341 87-012-157-080 C-CAP,S 330P-50 CH
C342 87-012-157-080 C-CAP,S 330P-50 CH
C343 87-012-157-080 C-CAP,S 330P-50 CH
C344 87-012-157-080 C-CAP,S 330P-50 CH
C350 87-010-197-080 CAP, CHIP 0.01 DM
C401 87-010-403-080 CAP, ELECT 3.3-50V
C402 87-010-197-080 CAP, CHIP 0.01 DM
C403 87-010-263-080 CAP, ELECT 100-10V
C404 87-010-248-080 CAP, ELECT 220-10V
C405 87-010-197-080 CAP, CHIP 0.01 DM
C406 87-010-374-080 CAP, ELECT 47-10V
C407 87-010-178-080 CHIP CAP 1000P
C408 87-010-198-080 CAP, CHIP 0.022
C409 87-010-248-080 CAP, ELECT 220-10V
C410 87-010-263-080 CAP, ELECT 100-10V
C411 87-A11-177-080 C-CAP,S 0.15-16 K B
C412 87-010-401-080 CAP, ELECT 1-50V
C413 87-016-369-080 C-CAP,S 0.033-25 B K
C414 87-010-405-080 CAP, ELECT 10-50V
C416 87-010-545-080 CAP, ELECT 0.22-50V
C417 87-012-157-080 C-CAP,S 330P-50 CH
C418 87-010-213-080 C-CAP,S 0.015-50 B
C419 87-A11-608-080 C-CAP,S 0.33-25 K B
C420 87-016-369-080 C-CAP,S 0.033-25 B K
C421 87-A11-177-080 C-CAP,S 0.15-16 K B
C422 87-010-184-080 CHIP CAPACITOR 3300P(K)
C423 87-A10-321-080 CHIP.CAP,S 0.047U/25V(Z)F
C424 87-A10-712-080 CHIP.CAP,S 0.22U/50V
C425 87-010-176-080 C-CAP,S 680P-50 SL
C426 87-A11-608-080 C-CAP,S 0.33-25 K B
C428 87-010-197-080 CAP, CHIP 0.01 DM
C429 87-010-186-080 CAP,CHIP 4700P
C430 87-012-156-080 C-CAP,S 220P-50 CH
C431 87-010-545-080 CAP, ELECT 0.22-50V
C432 87-010-374-080 CAP, ELECT 47-10V
C433 87-010-401-080 CAP, ELECT 1-50V
C434 87-010-184-080 CHIP CAPACITOR 3300P(K)
C435 87-010-197-080 CAP, CHIP 0.01 DM
C436 87-010-260-080 CAP, ELECT 47-25V
C437 87-010-404-080 CAP, ELECT 4.7-50V
REF. NO PART NO. KANRI DESCRIPTION
NO.
C438 87-012-368-080 C-CAP,S 0.1-50 F
C439 87-010-178-080 CHIP CAP 1000P
C440 87-010-145-080 C-CAP,S 1P-50 CH
C441 87-010-197-080 CAP, CHIP 0.01 DM
C442 87-010-314-080 C-CAP,S 22P-50V
C445 87-012-368-080 C-CAP,S 0.1-50 F
C446 87-012-368-080 C-CAP,S 0.1-50 F
C447 87-012-368-080 C-CAP,S 0.1-50 F
C448 87-010-315-080 C-CAP,S 27P-50 CH
C450 87-010-305-080 C-CAP 470P-50CH
C451 87-012-156-080 C-CAP,S 220P-50 CH
C455 87-010-247-080 CAP, ELECT 100-50V
C457 87-010-312-080 C-CAP,S 15P-50 CH
C458 87-010-312-080 C-CAP,S 15P-50 CH
C459 87-010-263-080 CAP, ELECT 100-10V
C460 87-015-819-080 CAPACITOR,0.01
C461 87-010-197-080 CAP, CHIP 0.01 DM
C462 87-010-248-080 CAP, ELECT 220-10V
C463 87-A11-132-080 AXIAL CAP 0.01U/50V(K)
C465 87-010-404-080 CAP, ELECT 4.7-50V
C466 87-012-368-080 C-CAP,S 0.1-50 F
C467 87-010-263-080 CAP, ELECT 100-10V
C469 87-012-154-080 C-CAP,S 150P-50 CH
C470 87-010-544-080 CAP, ELECT 0.1-50V
C471 87-A11-601-080 C-CAP,S 0.1-25 K B
C472 87-A11-601-080 C-CAP,S 0.1-25 K B
C473 87-A11-601-080 C-CAP,S 0.1-25 K B
C474 87-A11-601-080 C-CAP,S 0.1-25 K B
C475 87-015-819-080 CAPACITOR,0.01
C476 87-010-236-080 CAP,E 1000-10 SME
C477 87-010-197-080 CAP, CHIP 0.01 DM
C478 87-010-263-080 CAP, ELECT 100-10V
C479 87-010-197-080 CAP, CHIP 0.01 DM
C480 87-010-221-080 CAP, ELECT 470-10V
C481 87-010-405-080 CAP, ELECT 10-50V
C482 87-010-405-080 CAP, ELECT 10-50V
C489 87-012-368-080 C-CAP,S 0.1-50 F
C490 87-012-368-080 C-CAP,S 0.1-50 F
C491 87-015-819-080 CAPACITOR,0.01
C492 87-010-221-080 CAP, ELECT 470-10V
C493 87-010-184-080 CHIP CAPACITOR 3300P(K)
C494 87-A11-132-080 AXIAL CAP 0.01U/50V(K)
C501 87-016-495-000 EL CAP 3300UF/25V
C506 87-010-404-080 CAP, ELECT 4.7-50V
C507 87-010-401-080 CAP, ELECT 1-50V
C508 87-010-221-080 CAP, ELECT 470-10V
C511 87-010-263-080 CAP, ELECT 100-10V
C512 87-010-385-080 CAP, ELECT 220-25V
C521 87-010-197-080 CAP, CHIP 0.01 DM
C522 87-010-263-080 CAP, ELECT 100-10V
C544 87-010-405-080 CAP, ELECT 10-50V
C620 87-010-197-080 CAP, CHIP 0.01 DM
C762 87-010-198-080 CAP, CHIP 0.022
C765 87-016-669-080 C-CAP,S 0.1-25 K B
C766 87-010-260-080 CAP, ELECT 47-25V
C766 87-010-260-080 CAP,ELECT 47-25V
C4001 87-010-322-080 C-CAP,S 100P-50 CH
C4002 87-010-322-080 C-CAP,S 100P-50 CH
C4003 87-010-322-080 C-CAP,S 100P-50 CH
C4004 87-010-322-080 C-CAP,S 100P-50 CH
C4005 87-010-322-080 C-CAP,S 100P-50 CH
C4006 87-010-322-080 C-CAP,S 100P-50 CH
C4007 87-010-197-080 CAP, CHIP 0.01 DM
C4008 87-010-197-080 CAP, CHIP 0.01 DM
C4009 87-010-197-080 CAP, CHIP 0.01 DM
C4010 87-012-368-080 C-CAP,S 0.1-50 F
C5001 87-010-194-080 CHIP.CAP,S 0.047U/25V(Z)F
CF1 87-A90-128-010 FLTR,AM IF CFAL-455
CF2 82-785-747-010 CF MS2 GHY R
CF3 82-785-747-010 CF MS2 GHY R
5
Page 6
REF. NO PART NO. KANRI DESCRIPTION
CN0 8A-CT9-641-010 CONN,3P UL1007
CN401 87-A60-424-010 CONN,16P V TOC-B
CN501 87-049-919-010 CONN,3P EH V WHT
CN601 87-A60-109-010 CONN,2P V S2M-2W
CNA402 8Z-CT6-631-010 CONN ASSY,6P CD MO
L2 87-A50-347-010 COIL,FM BPF EX
L3 87-A50-349-010 COIL,BAR ANT AMW (COI)
L4 87-A50-345-010 COIL,FM RF EX
L5 87-A50-449-010 COIL,FM OSC U
L6 87-A50-337-010 COIL,AM OSC (TOKO)
L7 87-A50-336-010 COIL,AM IFT (TOKO)
L8 87-A50-335-010 COIL,FM IFT (TOKO)
L9 87-A50-334-010 COIL,FM DET (TOKO)
L10 87-005-849-080 COIL,10UH(CECS)
L330 88-CT6-620-010 REC OSC
L401 87-003-102-080 COIL, 10UH
L404 87-003-152-080 COIL, 100UH
L602 87-005-849-080 COIL,10UH(CECS)
L603 87-005-849-080 COIL,10UH(CECS)
PN301 87-A60-110-010 CONN,4P V S2M-4W
PN302 87-A60-111-010 CONN,5P V S2M 5W
PN751 88-CT6-608-010 CONN ASSY,8P MO
PN751 87-099-832-010 CONN,8P S2M-8W
PV1 87-A91-316-010 TUN-CAP,20P-160P U(TWD)
!
R761 87-029-019-010 RES, FUSEIBLE 1/2W-2.2
SFR430 87-024-437-080 SFR100K,RH063EC
SFR761 87-024-239-010 SFR,2.2K V RH0632C
SW1 87-A91-548-010 SW,SL-2-3 SK23E01G06
SW301 88-CT6-619-010 BACK SLIDE SW 6P2T SHORTIN
X401 8Z-CD5-633-010 VIB, CER16.93MHZ FCR16.93M2
FRONT C.B
C601 87-010-313-080 CAP, CHIP 18P
C602 87-010-315-080 C-CAP,S 27P-50 CH
C603 87-010-317-080 C-CAP,S 39P-50 CH
C604 87-010-314-080 C-CAP,S 22P-50V
C605 87-010-317-080 C-CAP,S 39P-50 CH
C606 87-010-197-080 CAP, CHIP 0.01 DM
C608 87-016-669-080 C-CAP,S 0.1-25 K B
C609 87-016-669-080 C-CAP,S 0.1-25 K B
C610 87-010-263-080 CAP, ELECT 100-10V
C611 87-016-669-080 C-CAP,S 0.1-25 K B
C612 87-010-248-080 CAP, ELECT 220-10V
C613 87-010-402-080 CAP, ELECT 2.2-50V
C614 87-010-196-080 CHIP CAPACITOR,0.1-25
C615 87-010-400-080 CAP, ELECT 0.47-50V
C616 87-010-401-080 CAP, ELECT 1-50V
C617 87-010-179-080 CAP,CHIP S B1200P
C618 87-010-263-080 CAP, ELECT 100-10V
C619 87-010-263-080 CAP, ELECT 100-10V
C830 87-010-197-080 CAP, CHIP 0.01 DM
C831 87-010-197-080 CAP, CHIP 0.01 DM
C832 87-015-628-080 C-CAP,1800P-50 B
C833 87-015-627-080 C-CAP,1000P-50 B
C834 87-010-404-080 CAP, ELECT 4.7-50V
C835 87-010-544-080 CAP, ELECT 0.1-50V
C836 87-015-627-080 C-CAP,1000P-50 B
C837 87-015-627-080 C-CAP,1000P-50 B
C838 87-010-401-080 CAP, ELECT 1-50V
C839 87-010-404-080 CAP, ELECT 4.7-50V
C840 87-010-221-080 CAP, ELECT 470-10V
C841 87-010-401-080 CAP, ELECT 1-50V
C842 87-012-140-080 CAP 470P
C844 87-010-401-080 CAP, ELECT 1-50V
J251 8A-CT9-630-010 JACK,MIC ST SW
J801 8A-CT9-630-010 JACK,MIC ST SW
L601 87-003-149-080 COIL,47UH
L801 87-003-098-080 FIXED IND 2.2UH K TP26
LCD601 8A-CT9-620-010 LCD,HLC7107ACT-9
NO.
REF. NO PART NO. KANRI DESCRIPTION
LED602 8Z-CT6-632-010 LED,L-934LID
LED603 8Z-CT6-632-010 LED,L-934LID
LED604 8Z-CT6-632-010 LED,L-934LID
LED605 8Z-CT6-632-010 LED,L-934LID
LED606 8Z-CT6-632-010 LED,L-934LID
LED607 8Z-CT6-632-010 LED,L-934LID
LED608 8Z-CT6-632-010 LED,L-934LID
LED609 8Z-CT6-632-010 LED,L-934LID
LED610 8Z-CT6-632-010 LED,L-934LID
SW600 8Z-CT6-636-010 SW,TACT EVQJAC04M
SW602 8Z-CT6-636-010 SW,TACT EVQJAC04M
SW603 8Z-CT6-636-010 SW,TACT EVQJAC04M
SW604 8Z-CT6-636-010 SW,TACT EVQJAC04M
SW605 8Z-CT6-636-010 SW,TACT EVQJAC04M
SW606 8Z-CT6-636-010 SW,TACT EVQJAC04M
SW607 8Z-CT6-636-010 SW,TACT EVQJAC04M
SW609 8Z-CT6-636-010 SW,TACT EVQJAC04M
SW610 8Z-CT6-636-010 SW,TACT EVQJAC04M
SW611 8Z-CT6-636-010 SW,TACT EVQJAC04M
SW612 8Z-CT6-636-010 SW,TACT EVQJAC04M
SW613 8Z-CT6-636-010 SW,TACT EVQJAC04M
SW614 8Z-CT6-636-010 SW,TACT EVQJAC04M
SW615 8Z-CT6-636-010 SW,TACT EVQJAC04M
SW616 8Z-CT6-636-010 SW,TACT EVQJAC04M
VR801 87-A90-768-010 VR,RTRY 10KAX1 1 H
X601 87-030-273-010 VIB,XTAL 32.768K5PPM
X602 87-A70-070-080 VIB,CER 5.76MHZ CRHF
PWR C.B
C901 87-A10-577-080 CAP,CER 0.022-50 Z YF
C902 87-A10-577-080 CAP,CER 0.022-50 Z YF
C903 87-A10-577-080 CAP,CER 0.022-50 Z YF
C904 87-A10-577-080 CAP,CER 0.022-50 Z YF
!
F901 87-035-139-010 FUSE, 2.5A T 250V<257 LH<S>>
!
F901 87-035-367-010 FUSE, 3.15A 250V<EXCEPT 257 LH
!
FC901 87-A90-160-080 FUSE CLAMP,FC 51F
!
FC902 87-A90-160-080 FUSE CLAMP,FC 51F
MOTOR C.B
M2 9X-262-576-910 MOTOR GEAR ASSY
PIN3 91-564-722-110 CONNECTOR 6P
SW1 91-572-085-120 LEAF SW
NO.
<S>>
6
Page 7
• Regarding connectors, they are not stocked as they are not the initial order items.
The connectors are available after they are supplied from connector manufacturers upon the order is received.
CHIP RESISTOR PART CODE
Chip Resistor Part Coding
88
LCD DISPLAY
A
Resistor Code
Chip resistor
Wattage Type Tolerance
1/16W 1005 5% CJ
1/16W
1/10W
1/8W
1608
2125
3216
5%
5%
5%
TRANSISTOR ILLUSTRATION
Symbol
CJ
CJ
CJ
Figure
Value of resistor
Form
L
Dimensions (mm)
t
W
0.55
Resistor Code
108
118
128
LW t
1.0 0.5 0.35 104
1.6 0.8 0.45
2 1.25 0.45
3.2
1.6
: A
: A
ECB
2SA1296
2SC1815
2SC2240
KTC3198
ECB
2SC2001
ECB ECB
2SA1318 2SA933
2SC1740
DTC114TS
C
B
E
2SC2714
ECB
DTC124XS
DTC114YK
ECB
2SB1655
87
Page 8
WIRING-1 (MAIN/FRONT)
1
A
B
234567
8
9
10
11 12 13
14
TC2
TC1
C
TC4
TC3
D
E
F
G
H
I
J
K
109
Page 9
SCHEMATIC DIAGRAM-1 (MAIN)
6
1
2
5
3
4
1211
Page 10
SCHEMATIC DIAGRAM-2 (CD)
1413
Page 11
SCHEMATIC DIAGRAM-3 (TUNER)
1615
Page 12
SCHEMATIC DIAGRAM-4 (FRONT)
1817
Page 13
WIRING-2 (PWR, MOTOR)
1
A
234567
MOTOR C.B
M2
SCHEMATIC DIAGRAM-5 (POWER)
B
C
D
E
F
CNA402
TO MAIN C.B
+
_
M2
(SLED MOTOR)
~
SW1
(INSIDE LIMIT SW)
M3
(SPINDLE MOTOR)
SW1
PIN3
_
+
~
M3
G
H
I
J
K
2019
Page 14
ELECTRICAL ADJUSTMENT
PRACTICAL SERVICE FIGURE
FRONTC.B MAINC.B
L008
L007
3
IC001
7
L009
4
1
L005
L006
19
TC1
TC3
PVC001
6
TC2
TC4
L004
2
5
L003
2
< TUNER SECTION >
1. AM Freq. Range Adjustment
L006 ....................................................................... 517kHz
TC003................................................................... 1750kHz
2. AM Tracking Adjustment
L003 ....................................................................... 600kHz
TC004................................................................... 1400kHz
3. AM IF Adjustment
Settings: • Test point: IC001 (L81828) 19PIN
• Adjustment location: L007
Method: Adjust L007 so that the output level at 1000kHz
becomes maximum.
4. FM Freq. Range Adjustment
L005 .....................................................................87.0MHz
TC001.................................................................109.0MHz
5. FM Tracking Adjustment
L004 .....................................................................90.0MHz
TC002.................................................................108.0MHz
6. FM IF Adjustment
Settings: • Test point: IC001 (L81828) 19PIN
• Adjustment location: L008
Method: Adjust L008 so that the output level at 98.0MHz
becomes balanced.
7. FM Balance Adjustment
Settings: • Test point: IC001 (L81828) 19PIN
• Adjustment location: L009
Method: Adjust L009 so that the output level at 98.0MHz
becomes balanced.
< TUNER SECTION >
< FM SECTION >
Sensitivity: Less than19dB (88.0MHz)
(THD 3%) Less than19dB (98.0MHz)
Less than19dB (108.0MHz)
Signal to Noise Ratio: More than 57dB (at 98.0MHz)
(Input 54dB)
Distortion: Less than 1.5% (at 98.0MHz)
(Input 54dB)
Intermediate frequency: 10.7MHz ±0.3MHz
Stereo separation: More than 18dB
< AM SECTION >
Sensitivity: Less than 45dB (at 600kHz)
(S/N 10dB) Less than 48dB (at 1000kHz)
Less than 45dB (at 1400kHz)
Distortion: Less than 1.5%
(Input 74dB)
Intermediate frequency: 450kHz±5kHz
< CASSETTE SECTION >
Tape speed: 3000Hz±30%
Wow & flutter: Less than 0.35% (JIS RMS)
Take-up torque: 30-60g-cm (DECK 1/2)
FF torque: 55-140g-cm (DECK 1/2)
Rew torque: 55-140g-cm (DECK 1/2)
Back tension: 3±2g-cm
S/N ratio: More than 40dB
Distortion: Less than 3.0% (PB)
Noise (PB): Less than 1mV
(AC/DC, MIN)
Erasing Ratio (W/FILTER): More than 40dB
98
J251
PHONES
L330
0
RPH (DECK1)/PH (DECK2)
9
8
SFR761
< TAPE SECTION >
8. Tape speed Adjustment
Settings: • Test tape: TTA-100
• Test point: J251 (PHONES jack)
• Adjustment location: SFR761
Method: Play back the test tape and adjust SFR761 so that
the frequency counter reads 3000Hz ±5Hz.
9. Head Azimuth Adjustment
Settings: • Test tape: TTA-320
• Test point: J251 (PHONES jack)
• Adjustment location: Azimuth adjustment
screw.
Method: Play back the 8kHz signal of the test tape and
adjust screw so that the output becomes
maximum.
10. Bias frequency Adjustment
L330 ............................................................. 56kHz ±2kHz
2221
Page 15
IC BLOCK DIAGRAM
IC, LA6541D IC, M61509
mono. SW
Control logic
IC, LA1828 IC, BA3416BL
DECK R
DECK R
R OUT
DECK L
DECK L
23
L OUT
TAPE SELECT
Page 16
VOLTAGE CHART
24
Page 17
25
Page 18
IC DESCRIPTION
IC, LA9241ML
Pin No. Pin Name I/O Description
Pin to which external pickup photo diode is connected. RF signal is created by adding
1
2
FIN2
FIN1
I
with the FIN1 pin signal. FE signal is created by subtracting from the FIN1 pin signal.
I
Pin to which external pickup photo diode is connected.
10
11
12
13
14
15
16
3
4
5
6
7
8
9
E
F
TB
TE-
TE
TESI
SCI
TH
TA
TD-
TD
JP
TO
FD
Pin to which external pickup photo diode is connected. TE signal is created by
I
subtracting from the F pin signal.
I
Pin to which external pickup photo diode is connected.
I
DC component of the TE signal is input.
Pin to which external resistor setting the TE signal gain is connected between the TE
I
pin.
O
TE signal output pin.
TES “Track Error Sense” comparator input pin. TE signal is passed through a band-
I
pass filter then input.
I
Shock detection signal input pin.
I
Tracking gain time constant setting pin.
O
TA amplifier output pin.
Pin to which external tracking phase compensation constants are connected between
I
the TD and VR pins.
I
Tracking phase compensation setting pin.
I
Tracking jump signal (kick pulse) amplitude setting pin.
O
Tracking control signal output pin.
O
Focusing control signal output pin.
17
18
19
20
21
22
23
24
25
26
27
28
29
30, 31
32, 33
34
FD-
FA
FA-
FE
FE-
AGND
SP
SPI
SPG
SP-
SPD
SLEQ
SLD
SL-, SL+
JP-, JP+
TGL
O
—
O
O
O
Pin to which external focusing phase compensation constants are connected between
I
the FD and FA pins.
Pin to which external focusing phase compensation constants are connected between
I
the FD– and FA– pins.
Pin to which external focusing phase compensation constants are connected between
I
the FA and FE pins.
FE signal output pin.
I
Pin to which external FE signal gain setting resistor is connected between the FE pin.
Analog signal GND.
Signal ended output of the CV+and CV- pin input signal.
I
Spndle amp input.
I
Pin to which external spindle gain setting resistor in 12 cm mode is connected.
Pin to which external spindle phase compensation constants are connected together
I
with SPD pin.
Spindle control signal output pin.
I
Pin to which external sled phase compensation constants are connected.
Sled control signal output pin.
I
Sled advance signal input pin from microprocessor.
I
Tracking jump signal input pin from DSP.
I
Tracking gain control signal input from DSP. Low gain when TGL = H.
35
TOFF
I
Tracking off control signal input pin from DSP. Off when TOFF = H.
26
Page 19
Pin No. Pin Name I/O Description
36
TES
O
Pin from which TES signal is output to DSP.
37
38
39, 40
41
42
43
44
45
46
47
48
49
50
51
52
53
HFL
SLOF
CV–, CV+
RFSM
RFS-
SLC
SLI
DGND
FSC
TBC
NC
DEF
CLK
CL
DAT
CE
O
O
O
—
O
—
O
“High Frequency Level” is used to judge whether the main beam position is on top of
bit or on top of mirror.
I
Sled servo off control input pin.
I
CLV error signal input pin from DSP.
RF output pin.
RF gain setting and EFM signal 3T compensation constant setting pin together with
I
RFSM pin.
“Slice Level Control” is the output pin which controls the RF signal data slice level by
DSP.
I
Input pin which control the data slice level by the DSP.
Digital system GND.
Output pin to which external focus search smoothing capacitor is connected.
I
“Tracking Balance Control” EF balance variable range setting pin.
No connection.
Disc defect detector output pin.
I
Reference clock input pin. 4.23 MHz of the DSP is input.
I
Microprocessor command clock input pin.
I
Microprocessor command data input pin.
I
Microprocessor command chip enable input pin.
54
55
56
57
58
59
60
61
62
63
64
DRF
FSS
VCC2
REFI
VR
LF2
PH1
BH1
LDD
LDS
VCC1
O
“Detect RF” RF level detector output.
I
“Focus Search Select” focus search mode (± search/+ search) select pin.
—
Servo system and digital system Vcc pin.
—
Pin to which external bypass capacitor for reference voltage is connected.
O
Reference voltage output pin.
I
Disc defect detector time constant setting pin.
I
Pin to which external capacitor for RF signal peak holding is connected.
I
Pin to which external capacitor for RF signal bottom holding is connected.
O
APC circuit output pin.
I
APC circuit input pin.
—
RF system Vcc pin.
27
Page 20
IC, LC78622ED
Pin No. Pin Name I/O Description
1
2
3
DEFI
TAI
PDO
I
Defect sense signal (DEF) input pin. (Connect to 0V when not used).
I
O
Test signal input pin with built-in pull-down resistor. Be sure to connect to 0V.
Phase comparator output pin to control external VCO.
4
5
6
7
8
9
10
11
12, 13
14
15
16
17
18
19, 20
21
VVSS
ISET
VVDD
FR
VSS
EFMO
EFMIN
T2
CLV+, CLK-
___
V/P
HFL
TES
TOFF
TGL
JP+, JP-
PCK
—
—
—
O
O
O
O
O
O
O
For PLL.
I
GND pin for built-in VCO. Be sure to connect to 0V.
Pin to which external resistor adjusting the PD0 output current.
Power supply pin for built-in VCO.
I
Pin for VCO frequency range adjustment.
Digital system GND. Be sure to connect to 0V.
For slice level control.
I
I
Test signal input pin with built-in pull-down resistor. Be sure to connect to 0V.
EFM signal output pin.
EFM signal input pin.
Disc motor control output. Three level output is possible using command.
Rough servo or phase control automatic selection monitoring output pin. Rough servo
at H. Phase servo at L.
I
Track detect signal input pin. Schmidt input.
I
Tracking error signal input pin. Schmidt input.
Tracking OFF output pin.
Tracking gain selection output pin. Gain boost at L.
Track jump control signal output pin. Three level output is possible using command.
EFM data playback clock monitoring pin 4.3218 MHz when phase is locked in.
22
23
24
25
26
27
28
29
30
31
32, 33
34
35
36
37
38
39
40
41
42
FSEQ
VDD
SL+
SL-
—
PUIN
_______
RW
EMPH
C2F
DOUT
T3, T4
N.C.
MUTEL
LVDD
LCHO
LVSS
RVSS
RCHO
RVDD
MUTER
O
—
O
O
—
O
O
O
O
—
O
—
O
—
—
O
—
O
Sync signal detection output pin. H when the sync signal which is detected from EFM
signal and thesync signal which is internally generated agree.
Digital system power supply pin.
Moves the sled to outer circumference.
Moves the sled to inner circumference.
Not connected.
I
CD pickup inner switch detection.
Read, wright signal.
De-emphasis monitor output pin. De-emphasis disc is being played back at H.
C2 flag output pin.
DIGITAL OUT output pin. (EIAJ format).
I
Test signal input pin with built-in pull-down resistor. Be sure to connect to 0V.
Not used. Set the pin to open.
L-channel mute output pin.
L-channel 1-bit DAC.
L-channel power supply pin.
L-channel output pin.
L-channel GND. Be sure to connect to 0V.
R-channel GND. Be sure to connect to 0V.
R-channel 1-bit DAC.
R-channel output pin.
R-channel power supply pin.
R-channel mute output pin.
28
Page 21
Pin No. Pin Name I/O Description
43
44
XVDD
XOUT
—
Crystal oscillator power supply pin.
O
Pin to which external 16.9344 MHz crystal oscillator is connected.
45
XIN
I
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
XVSS
SBSY
EFLG
PW
SFSY
SBCK
FSX
WRQ
RWC
SQOUT
COIN
___________
CQCK
RES
T11
16M
4.2M
T5
______
CS
T1
—
Crystal oscillator GND pin. Be sure to connect to 0V.
O
Subcode block sync signal output pin.
O
C1, C2, single and dual correction monitoring pin.
O
Subcode P, Q, R, S, T, U and W output pin.
O
Subcode frame sync signal output pin. Falls down when subcode enters standby.
Subcode read clock input pin. Schmidt input. (Be sure to connected to 0V when not
I
in use.)
Pin outputting the 7.35 kHz sync signal which is generated by dividing frequency of
O
crystal oscillator.
O
Subcode Q output standby output pin.
I
Read/write control input pin. Schmidt input.
O
Subcode Q output pin.
I
Command input pin from microprocessor.
I
Command input read clock or subcode read input clock from SQOUT pin
I
LC78622 reset input pin. Set this pin to L once when the main power is turned on.
O
Test signal output pin. Use this pin as open (normally L output).
O
16.9344 MHz output pin.
O
4.2336 MHz output pin.
I
Test signal input pin with built-in pull-down resistor. Be sure to connect to 0V.
Chip select signal input pin with built-in pull-down resistor. Be sure to connect to 0V
I
while it is not controlling.
I
Test signal input pin without built-in pull-down resistor. Be sure to connect to 0V.
29
Page 22
IC, LC867132V-5P07
Pin No. Pin Name I/O Description
1
2
3
O-RMC/CE
O-DATA
O-CLK
O
CD read/write control output and TU CE.
O
Data output to M62495FP.
O
Output CLK to tuner PLL.(Not connected)
10
11
12
13
14
15
16
17
18
19
20
21
22
4
5
6
7
8
9
—
O-CK SFT
I-HOLD
I-RST
XT1 (IN)
XT2 (OUT)
VSS1
CF1 (IN)
CF2 (OUT)
VDD1
I-ST IND
I-KEYO
I-CD SW
I-KEY1
I-MOTOR
I-REC
I-FM/AM
I-TU DO
O-BASS LED
—
O
O
—
O
—
O
Not Connected.
Clock shift output of the microcomputer.
I
Hold status detection.
I
Microcomputer reset.
I
Connected to 32.768KHZ crystal oscillator.
GND.
I
Connected to 6MHZ Ceramic Filter.
Power supply for microcomputer (+5V).
I
FM STEREO status input.
I
KEY AD input.
I
CD DOOR SW status detection input.
I
KEY AD input.
I
DECK MECHA MOTOR status input.
I
REC status input.
I
FM, AM status input. (Not connected)
I
Data input from tuner PLL.(Not connected)
BASS LED ON/OFF control output.
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37-40
41
42
43-54
O-QS LED
O-DUBB LED
O-INT
I-DRF
I-WRQ
I-REMO
S0-PA0
S1/PA1
S2/PA2
S3/PA3
S4/PA4
S5/PA5
S6/PA6
S7/PA7
S8~S11
VDD3
VSS3
S12~S23
O
O
O
O
O
O
O
O
O
O
O
O
—
—
O
Q-Sound LED ON/OFF control output.
LED control output used for high-speed dubbing.
INT DIODE MATRIX detection output.(Not connected)
I
CD RF level detection input.
I
CD sub-code Q standby input.
I
Remote control input.
LCD segment output.
LCD segment output.
LCD segment output.
LCD segment output.
LCD segment output.
LCD segment output.
LCD segment output.
LCD segment output.
Power supply for microcomputer (+5V).
GND.
LCD segment output.
55
O-CD LED
O
LED ON/OFF control output for CD functions.
30
Page 23
Pin No. Pin Name I/O Description
56
57
58
O-TU LED
O-TA LED
O-ROCK LED
O
LED ON/OFF control output for TU functions.
O
LED ON/OFF control output for TAPE functions. (Not Connected)
O
LED ON/OFF control output for ROCK.
59
60
61-63
64-66
67
68
69
70
71
72
73
74
75
76
77
78
79
O-POP LED
O-JAZZ LED
—
COM0-COM2
—
VSS2
VDD2
O-CD ON
O-TU ON
O-P.CONT
O-HI DUBB (NC)
O-MUTE
O-MO/ST
O-BEAT CONT
O-QSOUND
O-COIN
I-SQOUT
O
LED ON/OFF control output for POP.
O
LED ON/OFF control output for JAZZ.
—
Not connected.
O
LCD common output.
—
Not connected.
—
GND.
—
Power supply for microcomputer (+5V).
O
CD PWR control output.
O
TU PWR control output.
O
Power supply control output.
O
Dubbing speed control output.
O
Main mute output.
O
FM mono/stereo output.
O
BEAT switch over output.
O
Q-Sound ON/OFF output.
O
CD command output.
I
CD sub-code Q input.
80
O-CQCK
O
CLK for CD commands/sub-codes.
31
Page 24
MECHANICAL PARTS LIST 1/1
REF. NO PART NO. KANRI DESCRIPTION
1 8A-CT9-006-010 WINDOW,CASS L
2 8A-CT9-002-010 BOX,CASS L
3 8A-CT9-007-010 WINDOW,CASS R
4 8A-CT9-011-010 BTN,CD A
5 86-CT9-210-010 SPR-T,CASS
6 8A-CT9-003-010 BOX,CASS R
7 8A-CT9-019-010 KNOB,SL BAND
8 8A-CT9-008-010 WINDOW,DISP<EXCEPT 257 LH<S>>
8 8A-CT9-055-010 WINDOW,DISP LH<257 LH<S>>
9 8A-CT9-001-010 CABI,FR<EXCEPT 257 LH<S>>
9 8A-CT9-050-010 CABI,FR LH<257 LH<S>>
10 8A-CT9-021-010 LENS,POWER
11 8A-CT9-020-010 LENS,FUNC
12 8A-CT9-010-010 KEY,FUNC
13 8A-CT9-202-010 LEVER,BAND
14 8A-CT9-022-010 LENS,GEQ
15 8A-CT9-215-010 SPR-P,REC A
16 8A-CT9-023-010 BTN,QSOUND<EXCEPT 257 LH<S>>
17 8A-CT9-016-010 BTN,GEQ<EXCEPT 257 LH<S>>
17 8A-CT9-051-010 BTN,GEQ LH<257 LH<S>>
18 87-063-165-010 OIL-DMPR 150
19 8A-CT9-015-010 BTN,VOL
20 8A-CT9-012-010 BTN,CD B
21 86-CT9-208-010 HLDR,KEY CASS
22 8A-CT9-013-010 KEY,CASS L
23 8A-CT9-014-010 KEY,CASS R
24 8A-CT9-216-010 SPR-P,REC B
25 86-CT9-205-110 HLDR,REC
26 88-CD6-661-010 HLDR,BAR ANT.
27 88-CT6-606-010 FFC WIRE 16P(1.0 )
28 8A-CT9-208-010 DRUM,GEAR
29 88-CH6-220-010 CUSHION,CD A
30 8A-CT9-211-010 HLDR,GEQ
31 8A-CT9-205-010 HLDR,LCD
32 8A-CT9-203-010 HLDR,FUNC
33 8A-CT9-017-010 KNOB,RTRY MIC
34 8A-CT9-204-010 HLDR,POWER
35 8Z-CT6-214-010 RING,CHUCK
36 8Z-CT6-213-010 BASE,CHUCK
37 87-036-368-010 MAGNET
38 86-CT9-222-010 PLATE,MAGNET
39 86-CT9-217-010 HLDR,CHUCK A(S)
40 8A-CT9-004-010 BOX,CD
41 8A-CT9-005-010 WINDOW,CD
42 8A-CT9-009-010 POINTER,TUN
NO.
43 8A-CT9-207-010 HLDR,POINTER
44 8A-CT9-201-010 CHAS,CD
45 87-036-389-010 SW,PUSH LOCK<EXCEPT 247 U<S>>
46 8A-CT9-212-010 SPR-T,CD
47 8A-CT9-209-010 GEAR,POINTER
48 8A-CT9-210-010 GEAR,ADAP
49 8Z-CT9-064-010 PANEL CD
50 87-063-164-010 OIL-DMPR 80
51 8A-CT9-018-010 KNOB,RTRY TUN
52 8A-CT9-028-010 COVER, TUN
53 86-CT9-206-010 HLDR,TRANS<EXCEPT 257 LH<S>>
54 86-CT9-213-010 SPR-C,BATT(-)
55 86-CT9-207-010 HLDR,ANT
56 86-CT9-223-010 CUSH,FOOT
57 86-CT9-212-010 SPR-C,BATT LINK
58 8Z-CT9-044-010 CABI,REAR
59 86-CT6-036-010 HANDL,RF
60 88-CT6-022-010 COVER, HNDL
61 86-CT6-035-010 LID,BATT RF
62 86-CT9-040-010 BADGE,AIWA -<247 U<S>>
62 87-B00-010-010 BADGE,AIWA 30.5-5.2 S 2.5L
63 8A-CT9-030-010 NET,SPKR
64 8A-CT9-027-010 FRAME,SPKR NET
65 8A-CT9-024-010 CABI,SPKR FR
65 8A-CT9-025-010 CABI,SPKR FR R
66 86-CT9-117-010 CABI,SPKR-REAR L RF
66 86-CT9-118-010 CABI,SPKR-REAR R RF
67 86-CT9-121-010 HLDR,CORD RF
68 88-CT6-633-010 ANT,ROD
!
!
70 87-A60-178-010 JACK,AC E W/SW<257 LH<S>>
70 87-A60-177-010 JACK,AC U W/SW<EXCEPT 257 LH<S>>
71 8Z-CT9-059-010 PLATE,SPKR (3.2 OHM)<257 LH<S>>
A 87-751-097-410 SCREW 3X12
B 81-CD5-204-010 SCREW CD
C 87-751-095-410 VT2+3-8 W/O
D 87-571-095-410 VIT+3-8
E 87-651-100-410 VT1+3-16
F 87-651-075-210 VT1+2.6-10
G 87-651-104-410 VT1+3-30
H 87-261-072-410 V+2.6-5
REF. NO PART NO. KANRI DESCRIPTION
NO.
<EXCEPT 247 U<S>>
69 88-CT6-631-010 POWER TRANS,EI-57/25<257 LH<S>>
69 88-CT7-629-010 PT,U<EXCEPT 257 LH<S>>
COLOR NAME TABLE
Basic color symbol Color Basic color symbol Color Basic color symbol Color
B Black C Cream D Orange
G Green H Gray L Blue
LT Transparent Blue N Gold P Pink
R Red S Silver ST Titan Silver
T Brown V Violet W White
WT Transparent White Y Yellow YT Transparent Yellow
LM Metallic Blue LL Light Blue GT Transparent Green
LD Dark Blue DT Transparent Orange
32
Page 25
MECHANICAL EXPLODED VIEW 1/1
36
35
41
40
39
38
37
33
LCD
10
32
31
34
42
P.C.B
11
12
P.C.B
D
D
30
43
D
DA11T3C
HT-SINK
51
28
46
52
H
D
45
44
E
E
15
50
49
B
29
P.C.B
B
A
D
59
47
48
70
C
A
F
69
C
A
54
53
60
61
58
68
G
A
A
A
G
G
57
67
A
C
13
9
14
16
8
18
7
5
1
2
4
3
6
5
22
19
20
21
23
25
17
ZZM-2
15
A
A
A
21
D
26
24
A
A
62
27
P.C.B
P.C.B
D
D
A
63
64
56
55
C
C
A
71
65
G
66
A
A
3433
Page 26
TAPE MECHANISM EXPLODED VIEW 1/1
2
54
4
3
6
5
1
59
53
46
17
16
14
15
13
19
18
24
27
26
25
28
B
29
61
55
47
17
16
38
TERMINAL,LB1
22
21
20
14
b
15
13
19
18
A
TERMINAL,LB1
23
54
6
5
28
59
27
25
55
29
22
21
20
a
A
23
31
30
10
9
57
63
12
11
8
7
45
44
43
46
44
45
43
33
24
42
37
34
b
1
51
2
a
12
4
3
1
11
10
9
8
7
57
63
40
53
42
52
51
47
39
50
58
56
49
48
62
41
36
26
40
33
37
32
34
1
35
38
39
3635
Page 27
TAPE MECHANISM PARTS LIST 1/1
REF. NO PART NO. KANRI DESCRIPTION
NO.
1 8Z-ZM1-254-210 SPR-C,REEL R
2 8Z-ZM1-225-110 GEAR,REEL R
3 8Z-ZM1-253-110 SPR-C,AUTO SENSOR
4 8Z-ZM1-217-110 LEVER,AUTO SENSOR
5 8Z-ZM1-212-110 LEVER,T-UP
6 8Z-ZM1-245-010 SPR-T,AUTO
7 8Z-ZM1-236-010 CLR,SLIP FF/REW
8 8Z-ZM1-252-010 SPR-C,FF/REW
9 8Z-ZM1-230-010 GEAR,SLIP FF/REW A
10 8Z-ZM1-269-010 FELT,FF/REW 2
11 8Z-ZM1-238-110 GEAR,SLIP FF/REW B 2
12 8Z-ZM1-237-010 LEVER,FF/REW 2
13 8Z-ZM1-209-210 LEVER,PAUSE
14 8Z-ZM1-218-110 LEVER,E-LOCK H
15 8Z-ZM1-256-010 SPR-P,PAUSE
16 8Z-ZM1-244-010 SPR-T,T-UP
17 8Z-ZM1-247-210 SPR-T,PINCH
18 8Z-ZM1-261-110 ROLLER ASSY,PINCH
19 8Z-ZM1-221-010 LEVER,PINCH
20 8Z-ZM1-205-210 LEVER,PLAY
21 8Z-ZM1-248-110 SPR-T,BRG
22 87-A90-403-110 HEAD,RPH MS15R
23 84-ZM2-227-310 SPR-C,AZIMUTH
24 8Z-ZM1-216-010 LEVER,AUTO
25 8Z-ZM1-246-010 SPR-T,AUTO 2
26 8Z-ZM2-214-010 GEAR,IDL REW ZZM-2
27 8Z-ZM2-212-010 LEVER,STOP ZZM-2
28 8Z-ZM1-207-010 LEVER,FF
29 8Z-ZM1-206-010 LEVER,REW
30 8Z-ZM1-210-010 LEVER,REC<YR1NF>
30 8Z-ZM1-211-110 LEVER,REC 2<YR2NF,YR3NF>
31 87-A90-404-010 HEAD,EH LE15B<YR1NF>
31 87-A91-533-010 HEAD,EH PH-K380<YR2NF,YR3NF>
32 8Z-ZM2-218-010 LEVER,REC LOCK ZZM-2
33 87-A91-492-010 SW,LEAF MSW18560
REF. NO PART NO. KANRI DESCRIPTION
NO.
34 8Z-ZM1-226-010 GEAR,REEL L
35 8Z-ZM1-241-010 SPR-T,PLAY
36 8Z-ZM1-220-110 LEVER,REC SENSOR
37 8Z-ZM1-249-010 SPR-T,FR
38 8Z-ZM1-242-110 SPR-T,FF/REW
39 8Z-ZM1-229-010 GEAR,CAM
40 8Z-ZM1-232-010 GEAR,IDL FF/REW
41 8Z-ZM1-234-010 FLY-WHL,ZZM-1
42 8Z-ZM1-267-010 SHAFT,CAPSTAN 2
43 8Z-ZM1-228-010 GEAR,SLIP T-UP B
44 8Z-ZM1-265-010 FELT,T-UP
45 8Z-ZM1-227-010 GEAR,SLIP T-UP A
46 8Z-ZM1-251-110 SPR-C,T-UP SLIP
47 8Z-ZM1-243-210 SPR-T,STOP/PAUSE
48 87-A91-532-010 MOT,MS15U2LW1A
49 8Z-ZM1-235-010 PULLEY,MOT
50 8Z-ZM2-216-010 BELT,MAIN M
51 8Z-ZM1-260-010 SPR-P,CASETTE
52 8Z-ZM2-201-010 CHAS ASSY,ZZM-2
53 8Z-ZM1-255-110 SPR-T,E-LOCK
54 8Z-ZM2-219-010 LEVER,E-OPEN ZZM-2
55 8Z-ZM1-214-110 LEVER,LOCK
56 8Z-ZM2-211-010 FLY-WHL,ZZM-2
57 8Z-ZM1-257-110 SPR-C,F/R
58 8Z-ZM2-210-010 LEVER,BRIDGE<YR2NF,YR3NF>
59 80-ZM6-243-010 SH 1.75-3.6-0.5 SLT
60 87-A91-494-010 SW,LEAF MSW17820<YR1NF,YR2NF>
61 8Z-ZM1-241-010 SPR-T,PLAY<YR1NF>
61 8Z-ZM2-217-010 SPR-T,PLAY 2<YR2NF,YR3NF>
62 8Z-ZM2-601-010 CONN ASSY,9P ZZM-2<YR1NF>
63 8Z-ZM1-275-010 W-L,1.47-4-0.25
A 84-ZM2-242-010 S-SCREW,AZ1-2-6.4
B 8Z-ZM2-220-110 V+2.6 ZZM-2
37
Page 28
CD MECHANISM EXPLODED VIEW 1/1
SHAFT,SLIDE
B
SF-P101NR
CHASSIS
B
1
2
A
A
3
SPINDLE
MOTOR(M3)
MOTOR C,B
38
Page 29
CD MECHANISM PARTS LIST 1/1
REF. NO PART NO. KANRI DESCRIPTION
1 S2-121-A28-400 COVER GEAR
2 S2-511-A21-000 GEAR MIDDLE
3 S2-511-A21-100 GEAR,DRIVE
A S1-PN2-03R-OSE SCR PAN PCS 2-3
B 87-261-073-410 SCR S-TPG FLT 2.6-6
ALL M8-ZZK-E90-070 DA11T3C
NO.
39
Page 30
2–11, IKENOHATA 1–CHOME, TAITO-KU, TOKYO 110-8710, JAPAN TEL:03 (3827) 3111
931196
Printed in Singapore
Loading...