patent and other laws protecting intellectual property, as well as any specific agreements protecting
Airspan Networks Inc. rights in the aforesaid information. Neither this document nor the information
contained herein may be published, reproduced or disclosed to third parties, in whole or in part,
without the express, prior, written permission of Airspan Networks Inc. In addition, any use of this
document or the information contained herein for the purposes other than those for which it is
disclosed is strictly forbidden.
Airspan Networks Inc. reserves the right, without prior notice or liability, to make changes in
equipment design or specifications.
Information supplied by Airspan Networks Inc. is believed to be accurate and reliable. However, no
responsibility is assumed by Airspan Networks Inc. for the use thereof nor for the rights of third parties
which may be effected in any way by the use of thereof.
Any representation(s) in this document concerning performance of Airspan Networks Inc. product(s)
are for informational purposes only and are not warranties of future performance, either expressed or
implied. Airspan Networks Inc. standard limited warranty, stated in its sales contract or order
confirmation form, is the only warranty offered by Airspan Networks Inc. in relation thereto.
This document may contain flaws, omissions or typesetting errors; no warranty is granted nor liability
assumed in relation thereto unless specifically undertaken in Airspan Networks Inc. sales contract or
order confirmation. Information contained herein is periodically updated and changes will be
incorporated into subsequent editions. If you have encountered an error, please notify Airspan
Networks Inc. All specifications are subject to change without prior notice.
Product performance figures quoted within this document are indicative and for information purposes
only.
The WiMAX SSRM Antennas should be installed a minimum distance of 18.9 CM for the 1.4 GHz
variant, 36 Cm for the 2.3 GHz variant, 47 Cm for the 2.5 GHz variant and 25.4 Cm for the 3.65
GHz varient from your body.
Radio Interference
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to internal vehicle radio
communications.
Please ensure a maximum separation between the SSRM’s antenna and other antennas.
Modifications
Any changes and modifications to this device that are not expressly approved by Airspan
Networks are not permitted and if done will result in voidance of warranty.
General
Installation, replacement and service should be performed by qualified personnel who are
familiar with local safety codes.
Do not mount external antennas in inclement weather (such as rain or lightning) that may
increase risk of electrocution.
SSRM does not provide protection from hazard energy in case of single fault condition.
Power supply shall be limited up to 3A in normal and single fault condition.
Disclaimer Statement
The information in this document is subject to change without notice and does not represent a
commitment on the part of the vendor. No warranty or representation, either expressed or implied,
is made with respect to the quality, accuracy or fitness for any particular purpose of this
document. The manufacturer reserves the right to make changes to the content of this document
and/or the products associated with it at any time without obligation to notify any person or
organization of such changes. In no event will the manufacturer be liable for direct, indirect,
special, incidental or consequential damages arising out of the use or inability to use this product
or documentation, even if advised of the possibility of such damages. This document contains
materials protected by copyright. All rights are reserved. No part of this manual may be
reproduced or transmitted in any form, by any means or for any purpose without expressed
written consent of its authors. Product names appearing in this document are mentioned for
identification purchases only. All trademarks, product names or brand names appearing in this
document are registered property of their respective owners.
Page 7 Commercial in Confidence UWB-D00234 Rev C
Page 8
SSRM Module User Guide
DECLARATION OF CONFORMITY
European Community, Switzerland, Norway, Iceland, and Liechtenstein
Declaration of Conformity with Regard to the R&TTE Directive 1999/5/EC
English:
This equipment is in compliance with the essential requirements and other relevant provisions of
Directive 1999/5/EC.
Deutsch:
Dieses Gerät entspricht den grundlegenden Anforderungen und den weiteren entsprecheneden
Vorgaben der Richtlinie 1999/5/EU.
Dansk:
Dette udstyr er i overensstemmelse med de væsentlige krav og andre relevante bestemmelser i
Directiv 1999/5/EF.
Español:
Este equipo cumple con los requisitos esenciales asi como con otras disposiciones de la
Directive 1999/5/EC.
Greek:
ΜΕ ΤΗΝ ΠΑΡΟΥΣΑ Airspan ΔΗΛΩΝΕΙ ΟΤΙ Ο ΕΞΟΠΛΙΣΜΟΣ ΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣ ΤΙΣ
ΟΥΣΙΩΔΕΙΣ ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ ΤΙΣ ΛΟΙΠΕΣ ΣΧΕΤΙΚΕΣ ΔΙΑΤΑΞΕΙΣ ΤΗΣ ΟΔΗΓΙΑΣ 1999/5/ΕΚ.
Français:
Cet appareil est conforme aux exigencies essentialles et aux autres dispositions pertinantes de la
Directive 1999/5/EC.
Íslenska:
Þessi búnaður samrýmist lögboðnum kröfum og öðrum ákvæðum tilskipunar 1999/5/ESB.
Italiano:
Questo apparato é conforme ai requisiti essenziali ed agli altri principi sanciti dalla Direttiva
1999/5/EC.
Nederlands:
Deze apparatuur voldoet aan de belangrijkste eisen en andere voorzieningen van richtlijn
1999/5/EC.
Norsk:
Dette utstyret er i samsvar med de grunnleggende krav og andre relevante bestemmelser i EUdirectiv 1999/5/EC.
Português:
Este equipamento satisfaz os requisitos essenciais e outras provisões da Directiva 1999/5/EC.
Suomalainen:
Tämä laite täyttää direktiivin 1999/5/EY oleelliset vaatimukset ja on siinä asetettujen muidenkin
ehtojen mukainen.
Svenska:
Denna utrustning är i överensstämmelse med de väsentliga kraven och andra relevanta
bestämmelser i Direktiv 1999/5/EC.
Român:
Acest echipament este în conformitate cu cerinţele esenţiale şi alte prevederi relevante ale
Directivei 1999/5/CE.
The Declaration of Conformity related to this product can be obtained from
product_management@Airspan.com
Page 8 Commercial in Confidence UWB-D00234 Rev C
Page 9
SSRM Module User Guide
Caution: The SSRM PCIe module is intended for use only in the Cisco Field
Area Router – Cisco 1000 Series.
Note: Cisco 1000 series router exterior label shall include wording similar to
the following: “Contains FCC ID: PIDASMAX1400” or “Contains FCC ID:
PIDASMAX2350”or “Contains FCC ID: PIDASMAX2500”or “Contains FCC
ID:PIDASMAX3700” per appropriate variant.
FCC Notice
Federal Communication Commission Notice
The United States Federal Communication Commission (FCC) and the Canadian Department of
Communications have established certain rules governing the use of electronic equipment.
Part15, Class B.
This device complies with Part 15 of FCC rules. Operation is subject to the following two
conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause
undesired operation. This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation. This
equipment generates uses and can radiate radio frequency energy, and if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
Consult the dealer or an experienced radio/TV technician for help.
Page 9 Commercial in Confidence UWB-D00234 Rev C
Page 10
SSRM Module User Guide
Frequency
Band
FCC
TX EIRP
Antenna Gain
1.4GHz
26.18dBm
36.18dBm
10dBi
2.3 GHz
26dBm
42dBm
16dBi
2.5GHz
26.94dBm
44.44dBm
17.5dBI
3.65GHz
19.6dBm
39.1dBm
19.5dBI
3.65GHz
26.8dBm
32.4dBm
5.6dBI
Frequency
Band
ETSI
TX EIRP
Rest of the World
TX EIRP
Antenna Gain
1.4GHz
26.18dBm
36.18dBm
26.18dBm
36.18dBm
10dBi
2.3 GHz
26dBm
42dBm
26dBm
42dBm
16dBi
2.5GHz
26.94dBm
44.44dBm
26.94dBm
44.44dBm
17.5dBI
3.65GHz
26dBm
45dBm
26dBm
45dBm
19dBI
Caution: Do not set maximum output TX power to higher than local regulations.
Type
Frequency range
Gain
Part number
Dual Slant CPE
1.3-1.525 GHz
10dBi
MT-282025/CD
Directional Dual-Polarized Panel
2.3-2.36 GHz
16dBi
07-1160-01
Directional Dual-Polarized Panel
2.5-2.7 GHz
17.5dBi
07-1160-01
Directional Dual-Polarized Panel
3.3-3.8 GHz
19.5dBi
07-1161-01
Direct Mount LPT Style
3.3-3.8 GHz
5.6dBi
W1982
Note: Appropriate mounting kit (included) for the antenna(s) is required.
SSRM has two (2) RF ports that can be connected to two single-port antennas
Dual polarized antenna with two (2) ports - connected via 2 RF jumper cables.
Page 10 Commercial in Confidence UWB-D00234 Rev C
Page 11
SSRM Module User Guide
Frequency
Band
# of
Receivers
Sector
Antenna Type
# of Antennas
1.4 GHz
2
45º
1.3-1.525 GHz Dual Slant
Antenna - mounting included
1
2.3 GHz
2
45º
2.3-2.36 GHz Dual Polar
Antenna - mounting included
1
2.5 – 2.7 GHz
2
45º
2.5-2.7 GHz Dual Polar
Antenna - mounting included
1
3.3-3.8 GHz
2
45º
3.3-3.8 GHz Dual Polar
Antenna - mounting included
1
3.3-3.8 GHz
2
Omni
3.3-3.8 Monopole
1
The following table describes the antenna arrays:
Table 4 - Antenna arrays
Page 11 Commercial in Confidence UWB-D00234 Rev C
Page 12
SSRM Module User Guide
Icon
Description
Checkpoint: Marks a point in the workflow where there may be an exit or
branch to some other procedure. At each Checkpoint the reason for an exit
or branch is given along with specific directions to locate the entry point in the
other procedure.
Reference: Gives a resource in the workflow that may be needed to complete
a procedure along with specific directions to use the resource.
Caution: Describes a possible risk and how to lessen or avoid the risk.
Advice: Provides a recommendation based on best practice.
Note: Provides useful information.
1 About this Guide
This section discusses the purpose, intended audience, conventions, referenced documentation
and organization for this guide.
1.1 Purpose
The purpose of this User Guide is to provide step-by-step instructions for setting up, installing and
initial configuration of the SSRM Mini PCIe module. These procedures include:
Caution: A Cavity filter is required for the SSRM Mini PCIe module
deployment (ordered separately). WEVERCOMM WCS Cavity Filter Part No :
WVC-2.3GDB-3.5M01B
The Cavity filter must be connected between the RF output and the antenna.
Note: The diagram is for illustration purposes only.
2 Overview
The Airspan SSRM Mini PCIe module is a product specific WiMAX module designed to be
embedded in the Cisco Field Area Router – Cisco 1000 Series allowing WiMAX connectivity. The
Wireless protocols that come with this product ensure data security and isolation from
interference generated by other radio frequencies.
The SSRM module supports MIMO antenna technology and high power output.
2.1 SSRM Frequency Ranges
The table below lists the frequency range of SSRM models currently available. This table will
grow as more models become available.
Table 5 - SSRM Frequency Ranges
2.1.1 Main Features
The Airspan WiMAX SSRM Mini PCIe module provides the following main features:
Based on the WiMAX IEEE 802.16e wireless technology.
2.2 WiMAX Management
Software is upgraded locally and remotely.
Designed for local and remote management via the Host processor.
2.3 SSRM Block Diagram
The figure below displays a block diagram of the SSRM:
Figure 1 - Block Diagram
Page 13 Commercial in Confidence UWB-D00234 Rev C
Page 14
SSRM Module User Guide
Name
Quantity
Comments
Image
SSRM
10
PCIe module
3 Installation Prerequisites
Before installing your SSRM, read the following:
3.1 Package Contents
Examine the Airspan WiMAX SSRM shipping container. If you notice any damage, or missing
items as listed in the Packing List, immediately notify the carrier that delivered the unit and
contact an Airspan representative.
The SSRM kit should contain the following items:
SSRM Mini PCIe Module
Table 6 - Package Contents
Page 14 Commercial in Confidence UWB-D00234 Rev C
Page 15
SSRM Module User Guide
Parameter
Value
Dimensions (W x L x H)
PCIe Mini-Card Form Factor:
W: 51 mm (2.01”) (including PCIe connector);
L: 70 mm (2.36”)
H: 5.8mm (0.228”) (not including RF connectors)
Weight
0.1 Kg Approx. (100 grams Approx.)
4 Physical Description
This section provides a description of the components of the SSRM installation:
Dimensions
Connector
4.1 SSRM
The SSRM Mini PCIe module
Figure 2 – SSRM PCIe module
4.1.1 Physical Dimensions
The table below lists the physical dimensions of the SSRM Mini PCIe module.
Table 7 - SSRM physical dimensions
Page 15 Commercial in Confidence UWB-D00234 Rev C
Page 16
SSRM Module User Guide
Pin
Signal
Pin
Signal
1 26
GND
2
5.5V
27
GND
3 28 4
GND
29
GND
5 30 6 31
7 32
8 33 9
GND
34
GND
10 35
GND
11 36 12 37
GND
13 38 14 39
5.5V
15
GND
40
GND
16 41
5.5V
17 42 18
GND
43
GND
19 44 20 45 21
GND
46 22 47 23 48 24
5.5V
49
25 50
GND
51
SQN_RST
52
5.5V
4.2 Connector
The connector is described below:
Figure 3 - Mini PCI Connector
Table 8 - Connector 52 pin, pinouts
Page 16 Commercial in Confidence UWB-D00234 Rev C
Page 17
SSRM Module User Guide
Note: Carefully remove the SSRM Mini PCIe module from the packaging box
Caution: It is the responsibility of the person installing the SSRM module to
ensure that only those antennas certified for use with the product are used.
The use of any antenna other than those certified with the product is
expressly forbidden.
Caution: The SSRM module and the antennas must be installed only by
experienced installation professionals who are familiar with the local safety
codes and are licensed by the appropriate government authorities.
5 Connecting the SSRM Mini PCIe Module
To connect the SSRM Module:
1. Make sure the unit is turned off. Remove the cover from the unit.
2. Carefully slide the SSRM Mini PCIe module into the mini PCI slot. Align the pins and push
evenly and slowly and ensure it is properly seated.
3. After the device has been connected, Windows will detect the module and you will be
prompted to install the software and drivers.
5.1 Typical SSRM Installation
The following displays a typical installation with the SSRM Mini PCIe module installed.
Figure 4 - Typical SSRM installation
Page 17 Commercial in Confidence UWB-D00234 Rev C
Page 18
SSRM Module User Guide
6 Instillation of Drivers and Software
1. Exit all Windows programs. After recognizing the USB connection installation will initiate
automatically.
2. When prompted select the language to use during the installation.
Figure 5 - Setup language
3. Click OK to continue.
4. The Setup Wizard will walk you through the process.
Figure 6 - Setup wizard
5. Click Next to continue.
Page 18 Commercial in Confidence UWB-D00234 Rev C
Page 19
SSRM Module User Guide
Figure 7 - Select destination location
6. Click Next to continue.
Figure 8 - Select start menu folder
7. Click Next to continue.
Page 19 Commercial in Confidence UWB-D00234 Rev C
Page 20
SSRM Module User Guide
Figure 9 - Additional tasks
8. Select additional tasks, if required.
9. Click Next to continue.
Figure 10 - Ready to install
Page 20 Commercial in Confidence UWB-D00234 Rev C
Page 21
SSRM Module User Guide
10. Click Install to continue installation
Figure 11 – Installing
11. Wait while installation continues.
Figure 12 - Installation complete
Page 21 Commercial in Confidence UWB-D00234 Rev C
Page 22
SSRM Module User Guide
Note: Contact Customer support for specific editing instructions.
12. After Installation is complete click Finish.
6.1 Configuration
1. Navigate to the sequansd.xml file location C:\Program Files\Sequans Communication which
is used to configure frequency, bandwidth, etc. as shown below:
<?xml version="1.0"?>
-<sequansd>
<!-- DCC configuration -->
<!-- default config is listening on port 7771 on localhost. Change to IP address 0.0.0.0
for listening on all interfaces -->
3. After editing file, you need to restart sequansd service, as follows:
Navigate to - Start > settings > control panel > Administrative tools > Services
4. Choose service sequansd, right click > restart, as shown below:
Page 22 Commercial in Confidence UWB-D00234 Rev C
Page 23
SSRM Module User Guide
Figure 13 – Services
6.2 Connection Manager
Sequans Connection Manager - program which runs on the host to monitor the WiMAX link.
Navigate to - Start > Programs > Sequans Communications > Sequans CM
Figure 14 - WiMAX CM
The CM displays the downlink signal strength, uplink and downlink throughput counter:
Enable radio – check to enable radio
Link Status – displays current link status, such as:
Downlink
Uplink
Tools
Advanced
Page 23 Commercial in Confidence UWB-D00234 Rev C
Page 24
SSRM Module User Guide
Environmental
Input
5.5 VDC +/- 0.3 VDC through PCIe
DC Power Consumption
5.79 W
Operating Temperature
-40°C to +85°C
Operating Humidity
5% - 95%, non-condensing
EMC
FCC Part 15, Subpart B, Class B. According to
FCC only class A is required for outdoor unit
device.