Tube Queen AM/FM Radio & Bluetooth Speaker
R801W-3DI
Large collectible table-model Hi-Fi stereo radio /Bluetooth speaker
Tube Queen AM/FM Radio & Bluetooth Speaker
Product
Introducti
Tube Queen is a large table-model radio /Bluetooth speaker produced by our company.
This product uses the Hi-Fi concept and draws experience from Germany's excellent
radio design style in the 1950s to 60s. The product uses electronic tube to make power
amplifier and signal strength received indicator.
This product is a high-sensitivity radio with FM stereo reception and high-quality
Bluetooth speaker, but also a Hi-Fi tube amplifier that may be used separately. In case of
connection with external high-quality speaker, it can form a set of high-fidelity stereo
system.
This product is a multi-frequency radio that has four frequencies, namely, FM (FM)
stereo, medium wave (MW), shortwave 1 (SW1) and shortwave 2 (SW2), and uses
vacuum tube (commonly known as "cat’s eye") tuning indicator.
This product is also a high-quality Bluetooth audio speaker. Its Bluetooth program uses
the CSR 4.0 Bluetooth module that supports aptx lossless transmission. Hence, it can
guarantee excellent audio effect via Bluetooth.
This product uses high-power vacuum tube to make post amplification, so the output
power is strong. Coupled with the high-quality loudspeaker, and excellent circuit and
electro-acoustic design, this product has acquired sound effect unique to radio set. In
connection with stand-alone high-quality audio speaker, the Hi-Fi sound effect can be
achieved.
Table of
Contents
06
08
10
12
13
14
14
15
15
17
17
18
18
19
20
Picture Illustrations
Radio use instructions
Quick Guide
External antenna use
AFC function
External CD or other signal source
Bluetooth speaker use
Volume control
Loudspeaker System instructions
Product maintenance and safety
Radio case maintenance and use
Main technical indexes
Packing list
Common faults and removal
Radio knowledge
Figure 1
① Medium wave external antenna port
② FM antenna port
③ FM internal/external antenna transfer
switch
④ Short-wave proximity and remote
switch
⑤ Right channel inner /outer speaker
transfer switch
⑥ Right channel speaker port
⑦ Auxiliary input
⑧ Left channel speaker port
⑨ Left channel inner /outer speaker
transfer switch
⑩ Power port (in)
⑪ 230/115V transfer switch (Note: only
adjust under professional guidance)
Figure 2
⑫ Bluetooth /AUX / FM stereo and mono
FM transfer switch and AFC switch
⑬ Power switch / volume adjustment
⑭ Bass tuning
⑮ Auxiliary input / Bluetooth function
switch
⑯ FM transfer switch
⑰ Short wave II transfer switch
⑱ Short wave I transfer switch
⑲ Medium wave transfer switch
⑳ High volume tuning
○
21
Shortwave frequency fine tuning
○
22
Tuning knob
○
23
Cat’s eye tuning instructions
○
24
Radio station indication
Quic
k
1
Power supply voltage
2
Power switch and sound adjustment
(Figure 1) ⑩ is the powerport (in), which may be
connected with 230V or 115V alternating current
(AC) by use of standard three-pin plug (random
configuration). Before use, please check if the
voltage transfer switch (Figure 1) ⑪ is consistent
with the alternating current (AC). When the voltage
transfer switch is at 115V position, it can adapt to
110 - 120V/60HZ alternating current (AC); when the
voltage is at 230V position, it can adapt to
220-240V/50HZ alternating current (AC); the
switch’s factory setting is 230V (Note: only adjust
under professional guidance)
Panel (Figure 2) ⑬ is the power switch and
volume knob. By clockwise rotation, turn
the power on, and by counterclockwise
rotation, turn the power off. After power
on, continue to rotate to the right to
increase the volume to an appropriate
location (the volume knob is normally
adjusted to around ten o'clock direction).
Due to the use of vacuum tube amplifier,
vacuum tube needs about 30 seconds for
warming up before normal operation.
Therefore, the radio speaker will make a
sound 30 seconds later. Note that the
volume can’t be turned to the maximum
during these moments.
3 4 5
Wave selection
Search for radio broadcasting
Bluetooth play/ CD play and
auxiliary input
Front panel (Figure 2) ⑮ - ⑲ five key
switches are function and wave
selection keys. When a key is pressed,
the radio will start working under the
corresponding function or wave.
(Figure 2) ⑯-⑲ when a certain wave switch is pressed,
adjust the tuning button, (Figure 2) ○22 to search for
your favorite radio station. When the "cat’s eye" (Figure
2) ○23 shows the maximum, it means the tuning has
reached the optimal state.
See page 14: use of Bluetooth
function, CD and auxiliary
input.
Radio use
instructio
1
When the machine is used as a radio, it is of paramount
importance to place the machine and the external antenna
correctly. Otherwise, you may not receive any radio programs,
or only receive bad one! It is recommended to use the machine
close to window as much as possible. If it is impossible to use
the machine near the window, a group of external antennas will
be of great importance. The more professional the antenna and
antenna installation, the better the machine performance. In
addition, in case of connection with external antenna or not, it
should also be noted that the switch position for “internal/
external” antenna on the back of the machine must be correct!
Listen to FM broadcasting
This machine has equipped with built-in FM line. If the radio is placed
close to the window in the general urban area (not far from the radio
transmitting station), there is no need to use external antenna
generally. When external antenna (random accessory) is used, turn the
rear③(Figure 1) to the external (EXTERNAL) position. The external
antenna of this machine can also be connected with dedicated external
antenna or dedicated cable antenna. Press the (Figure 2) ⑯ key switch
on the front of the machine to be in FM wave, and adjust the tuning
knob to the range of 87--108MHZ for its radio programs. Turn the
transfer switch (Figure 2) ⑫ to FM position to be in ordinary FM state.
Turn to FM St position to be in stereo FM state. If the FM St effect is
not good enough, the switch can get a higher Signal to Noise Ratio
(SNR) at FM
2
Listen to medium wave broadcasting
Press (Figure 2) ⑲ switch to be in medium wave band, and turn the knob
(Figure 2) ○22 to listen to the radio programs within the range of
530-1610KHZ. This series of machine has high magnetic antenna. The AM
external antenna can also be used. Connect the two lines of the antenna to the
antenna clip, as shown in the figure below. Adjust the antenna to the best
direction, and then adjust the knob on the antenna (with external antenna for
tuning) to get the best signal. When the outdoor antenna is used, make
connection from (Figure 1) ①, and adjust the direction of external antenna to
get the clearest radio broadcasting.
3
Listen to AM shortwave broadcasting
The shortwave shared FM antenna (using external telescopic antenna for best effect) is
used as same as FM. This machine has shortwave 1 and shortwave 2. Press the front
keyboard switch ⑱ to be in shortwave 1 , press the front keyboard switch ⑰ to be in
shortwave 2, and adjust the tuning knob ○22 to find the desired radio broadcasting. In
shortwave 1, the radio programs within the range of 4.5-12MHZ can be received
(Figure 2). In shortwave 2, the radio programs within the range of 12-24MHZ can be
received. When the radio broadcasting is received, please turn the short or long distance
switch ④ on back of the machine to LONG-DISTANCE position. When the machine
is close to the station with strong signal, please turn the short or long distance switch to
the SHORT-RANGE position. Otherwise, it may cause overload . The (Figure 2)
"fine-tuning knob" may also be adjusted for fine-tuning in order to receive program in
the best state. The factory status is "remote".
Medium Wave antenna
connection diagram
Ground wire
Medium Wave antenna
Medium wave antenna
Medium Wave antenna
input diagram
Ground wire
Radio
external
antenna
FM/shortwave outdoor
antenna
Turn the internal and external
switch to external position
FM / shortwave antenna connection diagram
This machine is provided with exclusive FM / shortwave
antenna jack, which can be connected to exclusive
FM/shortwave outdoor antenna in order to enhance the
indoor reception effect.
AFC
F
unction
description
(Figure 2) ⑫ is FM stereo switch, which is provided with AFC
(automatic frequency control) switch. When the radio is affected
by environment and temperature, frequency shift phenomenon
might occur in the received radio program. In this case, AFC
function can improve the quality of reception. When using this
function, please note that the switch is turned to FM or FM ST
position to accurately receive the radio station, and then switch
is turned to FM AFC or FM ST AFC position. It is generally
recommended to use the machine under FM or FM AFC state.
External CD Player
or Other Signal Resource
Please connect audio signal output of CD or other auxiliary signal resource with
AUX IN port of the rear part of radio on the left (figure 1) ○17 through RCA
wire. When using, please press the key switch at the front panel of the radio
(figure 2)○15, and then turn the function switch to FM/AUX position (figure 2)○12.
After turning on the power switch and adjust to an appropriate position, a
beautiful sound effect unique to CD+ Tube Amplifier is available in a moment. If
using external loudspeaker, the sound effect would be different from the radio
one.
When choosing AUX, please remember to turn the AUX/AFC/BT on the bottom
left to a correct position. The knob should be in FM/AUX under AUX or
reception state。
Bluetooth Function Instructions
This radio is available for Bluetooth
player of telephone, Pad, and PC.
When using Bluetooth function,
please remember to turn the key
switch to “AUX” position and turn
the knob on the bottom left to BT
position. When not using Bluetooth,
please turn back to “FM/AUX”
position.
Attention： When using Bluetooth
function, it is necessary to pull out
the signal wire connecting AUX IN.
When connecting the signal
source, please notice the
correspondence of the L and
R track between the audio
source and radio AUX.
T
one
control
Speaker
s
ystem
d
escriptio
This machine inherits the design of the traditional radio in the 1960s, and is
provided with "bass" and "treble" toning knob. The user may adjust the two
knobs according to their own sound quality preferences, in order to achieve
the desirable sound quality.
Attention: in the power-on state, do not use external
loudspeaker, and be sure to turn the loudspeaker switch
(Figure 1) ⑤ and ⑨ back to INTERNAL state.
Otherwise, the amplifier circuit and output transformer
may be damaged!
Bass tuning
Figure 2 ⑭ is bass tuning knob. By clockwise rotation, the bass may be increased, and
by counterclockwise rotation, the bass may be reduced.
Treble tuning
Figure 2 ⑳ is the tuning knob. By clockwise rotation, the treble may be increased, and
by counterclockwise rotation, the treble may be reduced.
This product is equipped with a specially designed high-quality speaker
system that can be used for broadcasting or external sources. The machine
can also be connected with Hi-Fi speaker at rated power of about 20-50W,
so that the machine can have the unique sound quality.
When the external speaker is used, please turn the internal/external speaker
switch (Figure 1) ⑤, ⑨ on the back of machine to the external position.
When the speaker (Figure 1) is at ⑥ and ⑧ position, pay attention to the
speaker "+" terminal red binding post and "-" terminal black binding post.
Product
maintenance and
s
afety
Shell
maintenance
This product uses the shell made of solid wood. We give you the following
maintenance recommendations:
The vacuum tube is a glass
product and easy to be broken.
When using, it is careful not
to greatly collide with vacuum
tube.
Do not spill liquid on the
vacuum tube during the
machine's work and ensure
that it is used in a ventilated
place.
1.
Place this product away from
window, door, air vent and other
position with strong air flow to
avoid sunlight.
2.
Avoid excessive indoor dryness,
and do not put it in the vicinity of
heating in the winter. In autumn
and winter, it is recommended to
use humidifier for humidification.
When not in use, please turn
off the radio.
If not used for a long time,
please turn off the radio
power.
3.
When the humid weather comes,
open the air conditioning for
moisture removal, reduce the
moisture absorption of wood,
and avoid the expansion from
humidity on the tenon part in
case deformation and cracking.
4.
To keep the logs clean and tidy,
remove the dust with clean gauze.
Do not use chemical brightener to
avoid film sticking and damage. Use
soft brush or clean flannelette or silk
cloth. Do not use wet cloth or water
for cleaning.
Please do not use the product
for a long time beyond 10% of
the Alternating Current (AC).
The vacuum tube of the
machine is a heating element,
so it is normal for the machine
exterior and interior to have a
high temperature.
5.
Log shell can be properly
protected and cleaned with
paraffin water, walnut oil and
other protective plant oil on a
regular basis.
6.
There are many specific
maintenance measures accessible
in the Internet. In short, please
protect the shell of this product
against damaged, just like what
you do to your skin!
Main technical
Packing list
Frequency Range
FM: 87- 108MHz
MW: 530- 1610kHz
SW1 : 4.5 - 12MHz
SW2: 12-22MHz
Noise-limited
sensitivity
FM: 10uv (actual
measurement 8uv)
AM medium wave: 1.5mv
(actual measurement lmv)
shortwave : lOOuv (actual
measurement 80uv)
Degree of distortion
FM: 0.5%
MW: 1%
Signal to Noise Ratio
FM: >50dB
AM: >40dB
① Radio (1)
② User Guide (1)
③ Power line (1)
④ Backup fuse (1)
⑤ T antenna (1 )
⑥ Warranty card (1)
⑦ Auxiliary box
(optional) (2)
Amplifier frequency response
30Hz - 20KHz ( -3dB )
FM Stereo Separation
>35dB
Common faults
and removal
Fault phenomenon
Causes
Solution
No sound
1. Not power on
2. Not press the function switch
3. Volume knob in off position
4. Loudspeaker not in place
1. Pay attention to power connection
2. Press the corresponding function switch
(keyboard switch) to adjust the volume knob.
3. Turn the loudspeaker switch to current use
position
No sound from one side of built-in loudspeaker
Rear loudspeaker switch not in correct position
Turn the switch to correct position
No sound from one side of external loudspeaker box
1. Loudspeaker wire not connected well
2. Loudspeaker switch not in EXTSP position
1. Check the connection of loudspeaker wire
2. Turn the loudspeaker switch to EXT SP position
Discrete sound and lack of low frequency of external
loudspeaker box
Reverse connection of loudspeaker wire “+-”
Correctly connect loudspeaker wire
Volume distortion
1. Inaccurate tuning
2. excessive sound volume
3. Great increase in low or high pitch sound
1. Readjust radio station
2. Adjust the sound to the distortion free position
3. Turn the low pitch knob to proper position
Loud noise
1. Bad connection of antenna
2. Interference from external environment
1. Check antenna connection or turn the antenna
switch to corresponding position
2. Turn off the interference electric device or
change environment
Radio knowledge
①What is shortwave radio?
Many countries in the world use short frequency to perform worldwide broadcast transmission. Shortwave frequency
range is usually between 1.6MHz and 30MHz. The radio that can receive the frequency with the range is called
shortwave radio.
② What is “shortwave meter wave band”？
In general, we also divide the shortwave frequency into many "meter bands". Each meter band contains a frequency
range. For example, the 19M band contains a frequency range from 15.100 to 15.600MHz. The International Radio
Consultation Committee (CCIR) stipulates that the civil broadcaster uses the frequency within meter band range, and
the frequency beyond meter band is mostly used for military and other civilian communications. Therefore, the civil
broadcasting programs can only be received within the range of meter band frequency. (Please refer to the table
below)
Note: 1MHz (MHz ) = 1000kHz (kHz)
Band (M)
MHz(MHz )
KHz (GHz)
Radio distribution and listening effect
11
25.67-26.10
25670-26100
International wave band
Very few broadcasting stations
13
21.45-21.85
21450--21850
International wave band
Very few broadcasting stations, only specific station available
15
18.90-19.02
18900-19020
International wave band
Many broadcasting stations, good effect from noon to 9:00 pm;
common effect in the morning, and very few stations from late at night
to early morning
16
17.55-17.90
17550-17900
International wave band
19
15.10-15.60
15100-15600
International wave band
22
13.60-13.80
13600-13800
International wave band
Good effect at dusk, but not many radio stations
25
11.65-12.05
11650-12050
International wave band
Maximum broadcasting stations, good effect all day long, and best
effect in the morning, at dust and to 12 o'clock.
31
9.50-9.90
9500--9900
International wave band
41
7.10-7.35
7100-7350
International wave band
Many broadcasting stations in the morning, evening and late at night,
but susceptible to interference, and loud noise
49
5.95-6.20
5950-6200
International wave band
60
4.75-5.06
4750-5060
Regional wave band
75
3.90-4.00
3900-4000
International wave band
90
3.20-3.40
3200-3400
Regional wave band
Good effect at night, but no many broadcasting stations, bad effect and
loud noise during daytime
120
2.30-2.495
2300--2495
Regional wave band
③
④
Effect of listening to shortwave programs at different times of the day
What language programs can be received by
shortwave radios?
Shortwave signal propagation is subject to the influence of many factors, such as sunspot
activity, atmosphere and earth-ionosphere change. The shortwave propagation effect varies with
band, sometime good in the daytime or at night. It is not good to listen to shortwave program
during daytime, especially from 10 am to 3 pm. It is mainly because that shortwave is greatly
affected by the change of ionosphere in such period, leading to short transmission distance. If
you want to listen to shortwave programs during the daytime, please refer to the table above.
The effect may be good in certain meter bands, but inferior to that at night.
If in China, in shortwave radio programs, the Mandarin,
English, French, German, Russian, Japanese, Hindi,
Spanish, Portuguese, and other languages may be
heard, as well as our Cantonese, Teochew dialect,
Shanghai dialect, Minnan dialect and other dialects.
China's Central People's Broadcasting Station also uses
Mongolian, Uygur, Tibetan, Kazakh, Korean and other
minority languages for short-wave radio broadcasting.
⑤
⑥
⑦
What kind of radio
broadcasting can be received by
shortwave radio?
What content in the
shortwave program?
Is there the need to use outdoor external antenna
to listen to shortwave radio broadcasting?
Most countries in the world have
shortwave radio broadcasting. However,
the shortwave radio station in a certain
small country can only cover the territory
of such country, owning to small
transmitting power, which cannot be
received well by our country. Even a
station with strong power, the receiving
effect depends on geographical location
within or beyond coverage range. For
example: some frequencies of China's
Central People's Broadcasting Station
shortwave radio broadcasting can be
received well in our northeastern region,
but badly in China's southwest region.
Thanks to the national cultural and
political background of different
countries, the shortwave radio content
varies with country. In general, the
international shortwave radio program
contains world news, national news and
local news, news reviews, national
culture, music appreciation, language
teaching, etc. Some countries even set
up police information announcement,
weather forecast, marine information
forecast and other program. It must be
stressed that the official radio station of
each national government represents its
political positions and economic
interests. Therefore, when listening to
international broadcasting, you should
have ability to make judgment.
This depends on your listening environment. The reinforced
structures will shield the broadcast signal. In some remote areas,
mountains and mining areas, the shortwave signal will be slightly
weak, so it is necessary to install the outdoor antenna.
⑧
Is the shortwave signal clear?
The effect of listening to shortwave broadcasting depends on the
strength of radio transmitting power, the performance of radio and
the receiving location and other environmental factors. With the
improvement of radio technology, the listening effect will get
better and better.
○
9
⑩
How to test the effect of an
external antenna?
Must the external antenna be very high and long?
In a general listening environment,
turn the radio to a relatively weak
shortwave radio station, and go outside
of the room while listening. If the
shortwave radio signal is enhanced,
outdoor antenna should be installed to
improve the receiving effect. However,
if there is a strong TV station, FM
radio, BP machine and other radio
communication antenna near the
receiving location, the strong
interference signal will cause poor
receiving effect of shortwave external
antenna.
In short, shortwave external antenna will get better effect if it is high and long. But, higher and longer antenna doesn’t
imply better effect. Sometimes, sensitive antenna will introduce strong radio interference wave. Therefore, the height
and length of the external antenna should be adjusted according to the actual needs.
○
11
FM broadcasting
FM (FM) is a close-range high-fidelity radio system, which is the broadcast system with most rapid development, the
largest number, and best sound quality.
In some developed countries, a city even has 30 FM radio stations. Since the 1980s, China has built a large number of
FM radio stations, and almost all of them can play stereo programs. China FM radio frequency: 87 ~ 108 MHz, the
frequency interval 0.1 MHz, radio frequency from several hundred watts to twenty kilowatts.
Special warning: do
not install outdoor
antenna in the
multi-lightning area!
○
12
What signal will affect FM reception?
Powerful VHF TV radio broadcasting and personal
computer switching power supply radio wave will
interfere with the FM reception. In addition, the
FM radio stations with adjacent frequency and
strong transmitting power will interfere with each
other, leading to poor reception effect.
○
13
How far is the receiving distance of
the FM radio?
FM radio frequency is very high, and the radio is
transmitted in a linear way. The higher the
transmitting antenna, the greater the power, the
larger the coverage, and the farther the transmission
distance. FM radio transmission distance is usually
30 to 100 km.
○
14
How to reduce the interference of
FM?
Shorten the lever, change the direction of the
antenna, change the listening position, and keep
away from personal computer equipment, to
reduce the degree of interference.
○
16
Shortwave radio
Shortwave is transmitted mainly relying on the reflection
and refraction between ionosphere and the ground,
regardless of day and night. Shortwave can be transmitted
very far, so the radio can listen to the long-range radio
sound in shortwave band.
⑮
How to achieve long distance
listening of FM radio?
Use VHF outdoor TV antenna and antenna
amplifier. Install the antenna as high as
possible, align the antenna at the direction of
the FM radio, and connect to the
radiotelescopic antenna with 75 ohm coaxial
cable, so that the receiving capacity can be
greatly improved. Some cities have used cable
television networks to transmit cable FM
programs. Attempt may be made to pull the
antenna from a cable jack.
Shortwave frequency is between 2 and 30 MHz, and is
divided into civilian broadcasting meter band and
communication dedicated band. Civil broadcast use
amplitude modulation system and shortwave
communication typically uses single sideband (SSB)
system.
⑰
Why does the shortwave radio sound
suddenly rise or decline?
The ionosphere that propagates the shortwave is unstable,
because its thickness, height and ionospheric density
change at any time, especially during daytime. The
shortwave signal arriving at the radio is sometimes strong
or weak. Therefore, when listening to shortwave
broadcasting, the sound may suddenly rise or decline. This
phenomenon may be mitigated for the radio with good
automatic gain control <AGC> performance.
⑱
Medium wave broadcasting
Medium wave is the world's first and
most widely used folk broadcasting
band, which is mainly applied in
domestic, provincial and municipal,
regional and other medium-distance
radio, and has rich programs.
Wave broadcast characteristics: short
range during daytime, and long distance
during night, easy to suffer from the
interference from lightning and
household appliances.
China medium wave broadcast
frequency: 525~1610kHz, step length
9kHz.
19
○
Why more radio stations received at night
than that of the daytime?
Medium wave propagation mainly relies on the ground
wave. Only a small amount of medium wave is transmitted
by relying on sky wave.
When a radio wave encounters conductor, conductor will
generate induced current, consuming a portion of energy.
The phenomenon that weakens the radio wave energy is
called the absorption of radio wave.
The ground is a conductor, which has high absorption of
medium wave. So, the medium wave cannot be transmitted
for a long distance in the form of ground wave (about two
or three hundred kilometers).
Due to sunlight and ionization density increase during the
daytime, the ionosphere becomes a good conductor, such
that a small part of the medium waves propagated in the
form of sky wave will be strongly absorbed, and difficult
to return to the ground. Moreover, the medium waves
propagated in the form of ground wave are absorbed by the
earth and can’t be transmitted for a long distance. So it is
difficult to receive the medium wave radio stations during
the daytime.
At night, the atmosphere is not subject to sunlight, and the
mutual recombination of ionospheric electrons and ions is
significantly increased. Hence, the ionosphere becomes
thinner, the density becomes smaller, the conductivity
becomes poorer, and the radio wave absorption is also
greatly weakened. At this time, the medium wave can be
transmitted to a remote place through sky wave, so the
more medium wave radio stations could be received at
night.
20
○
What factor will affect broadcasting
reception effect?
The reception environment is the main factor that affects
the broadcast reception!
In the receiving environment in modern city, there are
many waves that may interfere with the radio, such as FM
radio, wireless phone, personal computer switching power
supply and powerful shortwave SSB communication
station. It is very difficult to listen to shortwave programs
near such places; furthermore, various motors, cars,
televisions, microwave ovens, SCR equipment, and the
fluorescent lamps and poor quality energy-saving lamps
that use electronic rectifier will seriously affect the
medium wave broadcasting.
The mutual interference of a large number of FM radio
stations and VHF TV will also make the FM radio receiver
worse. The second problem may be the radio itself.
FCC Warning:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.
ISED
Warn
ing:
-English Warning Statement:
"This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference,
and (2) this device must accept any interference, including interference that may cause undesired operation of the device."
The digital apparatus complies with Canadian CAN ICES-3 (B)/NMB-3(B).
-French Warning Statement:
"Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes :
(1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en
compromettre le fonctionnement."
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du
Canada.
This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment and meets RSS-102 of the IC radio frequency (RF) Exposure rules.
This equipment has very low levels of RF energy that are deemed to comply without testing of specifc absorption ratio (SAR).Cet équipement est conforme aux limites d'exposition
aux rayonnements énoncées pour un environnement non contr?lé et respecte les règles d'exposition aux fréquences radioélectriques (RF) CNR-102 de l'IC.
Cet équipement émet une énergie RF très
faible qui est considérée conforme sans évaluation du débit d'absorption spécifque (DAS).
The device complies with RF specifications.
Loading...