AirLive PoE-2600HD User Manual

AirLive PoE-2600HD /WN-2600HD

802.3af PoE H.264 2.0 Mega-Pixel PT IP Camera /Wireless N H.264 2.0 Mega-Pixel PT IP Camera

User’s Manual

AirLive PoE-2600HD/

WN-2600HD User’s Manual

Owner's Record

The model and serial numbers are located at the bottom of device. Record these numbers in the spaces provided below. Refer to these numbers whenever you call upon your dealer regarding this product.

Model No. ____________________

Serial No. ____________________

To prevent fire or shock hazard, do not expose the unit to rain or moisture. For AC Adaptor to avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only.

AirLive PoE-2600HD/

WN-2600HD User’s Manual

Notice: The changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

For customers in the U.S.A.

This equipment has been tested and found to comply with the limits for a digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

– Reorient or relocate the receiving antenna. – Increase the separation between the equipment and receiver. – Connect the equipment into an outlet on a circuit different from that to which the receiver

is connected.

– Consult the dealer or an experienced radio/TV technician for help.

You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment.

The shielded interface cable recommended in this manual must be used with this equipment in order to comply with the limits for a digital device pursuant to Subpart B of Part 15 of FCC Rules.

Declaration of Conformity

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may

cause undesired operation.

AirLive PoE-2600HD/ WN-2600HD User’s Manual

IMPORTANT NOTE: To comply with the FCC RF exposure compliance requirements, no change to the antenna or the device is permitted. Any change to the antenna or the device could result in the device exceeding the RF exposure requirements and void user’s authority to operate the device.

NOTICE TO USERS

© 2006~11 All rights reserved. This manual or the software described herein, in whole or in part, may not be reproduced, translated or reduced to any machine readable form without prior written approval.

This product contains some codes from GPL. In compliance with GPL agreement, AirLive will publish the GPL codes on our website. Please go to www.airlive.com and go to the "Support->GPL" menu to download source code.

WE PROVIDES NO WARRANTY WITH REGARD TO THIS MANUAL, THE SOFTWARE OR OTHER INFORMATION CONTAINED HEREIN A ND HEREBY EXPRESSLY DISCLAIMS ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE WITH REGARD TO THIS MANUAL, THE SOFTWARE OR SUCH OTHER INFORMATION. IN NO EVENT SHALL WE BE LIABLE FOR ANY INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES, WHETHER BASED ON TORT, CONTRACT, OR OTHERWISE, ARISING OUT OF OR IN CONNECTION WITH THIS MANUAL, THE SOFTWARE OR OTHER INFORMATION CONTAINED HEREIN OR THE USE THEREOF.

We reserve the right to make any modification to this manual or the information contained herein at any time without notice. The software described herein may also be governed by the terms of a separate user license agreement.

AirLive PoE-2600HD/

iii

WN-2600HD User’s Manual

Table of Contents

1. Introduction.................................................................................................................3

1.1 Overview..............................................................................................................3

1.2 Package Contents ...............................................................................................5

1.3 Physical Description ............................................................................................6

1.4 Mounting the Camera..........................................................................................9

1.5 Install the Camera in LAN..................................................................................10

2. Preparation................................................................................................................12

2.1 Search and Set up by IPWizard II......................................................................12

2.1.1 Search.....................................................................................................12

2.1.2 View.........................................................................................................14

2.1.3 LAN .........................................................................................................15

2.1.4 Wireless (WN-2600HD Only)...................................................................18

2.2 UPnP of Windows® XP, Vista or 7.....................................................................23

2.3 Install the Device behind a NAT Router .............................................................23

2.4 Access the Device from the Internet Explorer for the First Time........................24

2.5 Logging in as an User........................................................................................26

2.6 Logging in as an Administrator ..........................................................................26

3. Operating the Network Camera ...............................................................................27

4. Administrating the Device........................................................................................34

4.1 Network: Configure Network Settings................................................................35

4.1.1 Network ...................................................................................................35

4.1.2 Wireless (WN-2600HD Only)...................................................................37

4.1.3 DDNS Service .........................................................................................41

4.1.4 PPPoE.....................................................................................................43

4.1.5 Streaming................................................................................................45

4.1.6 UPnP.......................................................................................................46

4.1.7 Bonjour....................................................................................................47

4.1.8 IP Filter....................................................................................................48

4.1.9 IP Notification ..........................................................................................49

4.2 Camera: Adjust Camera Parameters.................................................................52

4.2.1 Picture .....................................................................................................52

4.2.2 Preset Setting..........................................................................................54

4.2.3 Tour Setting.............................................................................................55

4.3 System: Configure and Maintain System...........................................................56

4.3.1 System ....................................................................................................56

4.3.2 Date & Time.............................................................................................58

i AirLive PoE-2600HD/

WN-2600HD User’s Manual

Table of Contents

4.3.3 Maintenance............................................................................................59

4.4 Video: Configure Profile.....................................................................................62

4.4.1 Common..................................................................................................62

4.4.2 Video Profile............................................................................................63

4.4.3 ROI..........................................................................................................64

4.5 Audio: Audio Parameters ...................................................................................65

4.6 User: Manage User Name, Password and Login Privilege................................66

4.7 E-Mail: Setup E-Mail Configuration....................................................................67

4.8 Object Detection: Setup Object Detection .........................................................68

4.9 Storage: Status and Configuration of SD Card ..................................................70

4.10 Recording List: Files List Inside the SD Card ..................................................71

4.11 Event Server: Setup FTP/TCP/HTTP/SAMBA Server Configuration................71

4.11.1 FTP Server............................................................................................71

4.11.2 TCP Server............................................................................................73

4.11.3 HTTP Server..........................................................................................74

4.11.4 SAMBA Server ......................................................................................75

4.12 Event Schedule: Configure the Event Schedule..............................................76

4.12.1 Setting ...................................................................................................76

4.12.2 Record...................................................................................................80

5. Appendix....................................................................................................................82

Appendix A: Alarm I/O Connector ............................................................................82

Appendix B: Troubleshooting & Frequently Asked Questions..................................84

Appendix C: PING IP Address .................................................................................89

Appendix D: Bandwidth Estimation..........................................................................90

Appendix E: Specifications......................................................................................91

Appendix F: Configure Port Forwarding Manually ...................................................93

Appendix G: DDNS Application ...............................................................................96

Appendix H: Power Line Frequency ......................................................................102

Appendix I: 3GPP..................................................................................................104

Appendix J: Enable UPnP of Windows XP............................................................105

AirLive PoE-2600HD/ WN-2600HD User’s Manual

1. Introduction

1.1 Overview

This user’s guide explains how to operate this camera from a computer. User should read this manual completely and carefully before you operate the device.

This camera is an inexpensive and fully scalable surveillance device. Because the Network Cameras can be plugged into your existing local area network (LAN), you will potentially save thousands of dollars from unnecessary cabling.

3 AirLive PoE-2600HD/

WN-2600HD User’s Manual

1. Introduction

The device is accessible via the LAN or Internet connection. Connect your device directly to a local area network or xDSL modem, and with Microsoft® Internet Explorer you get instant, on demand video streams. Within minutes you can set up the device to capture a video sequence to a PC. The live video can be uploaded to a website for the world to see.

Features

z Easy installation with setup wizard (IP Wizard II) z UPnP device discovery and NAT router transversal for easy installation z Dynamic IP Service, DIPS®, to search your IP camera from Internet easily z Wide and fast Pan range: 355 degree and 90 degree/sec z Wide and fast Tilt range: 120 degree and 90 degree/sec z H.264, MPEG4 and JPEG triple compression simultaneously z 2 Mega-pixel resolution z 20-profile encoder simultaneously z UDP / TCP / HTTP protocols selectable z IEEE 802.11n wireless LAN (WLAN model) z WEP/WPA/WPA2-PSK wireless security (WLAN model) z 3GPP for 3G mobile remote application z Digital zoom z Built-in 12 high-light LEDs for night mode or low Lux. environment z Built-in microphone z Audio line out z Two-way audio z Intelligent motion detection up to 10 zones z Go to preset once motion triggered z Image transmission using an FTP or e-mail for event z DDNS and PPPoE z Multi-channel control software for surveillance application z On-line firmware upgrade z Support Wireless N 150Mbps

Minimum System Requirements

z Microsoft Internet Explorer 6.0 or later z Microsoft Media Player 11.0 or later (to playback recorded file) z VGA Monitor resolution 1280 x 1024 or higher z Pentium-4 3.6 GHz or higher z Memory Size: 1GB or more z Windows XP, Vista, 7

AirLive PoE-2600HD/ WN-2600HD User’s Manual

1. Introduction

1.2 Package Contents

User can find the following items in the package:

1. This camera is the main element of the product.

2. Camera mount kit and pads.

3. Detachable WLAN antenna (for WN-2600HD WLAN model only).

4. Power adapter dedicates 12V DC electric power output to Network Camera.

5. User’s manual CD provides important information and instructions for operating the

Network Camera.

6. Quick start guide provides important information and instructions for installing this

device.

If any of the above items are missing, please contact your dealer immediately.

Note: Using a power supply with a different voltage than the one included with the Network Camera will cause damage and void the warranty for this product.

5 AirLive PoE-2600HD/

WN-2600HD User’s Manual

1.3 Physical Description

Front View

1. Introduction

z High-light LEDs

These LEDs are high power LED type. It’s very useful for low-lux environment to provide supplementary light source for image sensor.

z Lens & focus ring

User could use this ring to adjust focus manually.

z Microphone

The Camera has built-in an internal microphone. This microphone is hidden in the pinhole located on the front panel.

AirLive PoE-2600HD/ WN-2600HD User’s Manual

Rear View

1. Introduction

z Audio Output Jack

Audio-out Jack allows this device to output audio or alerting sound.

z DC Power Jack

The input power is 12VDC. Note that supply the power to the Camera with the power adapter included in package. Otherwise, the improper power adapter may damage the unit and result in danger.

z Antenna Connector

User can attach the included antenna to this connector (SMA type) or use another high-gain antenna to get higher performance.

z Factory Default Reset

This button is hidden in the pinhole. This button is used to restore the all factory default settings. Sometimes restarting the camera will make the system back to a normal state. If the system still got problems after restart, user can restore the factory default settings and install it again. To restore the device, please follow the steps below:

7 AirLive PoE-2600HD/

WN-2600HD User’s Manual

1. Introduction

1. Insert the paper clip or other tool and press and hold the button down continuously.

2. Hold it at least 5 seconds and release the tool. Then the device has been restored

to default settings and reboot again.

Note: Restoring the factory default setting will lose the all previous settings included

IP address forever. User needs to run the IPWizard II program to search the device and configure it to let the device work properly again.

z LAN Socket

The LAN socket is a RJ-45 connector for connections to 10Base-T Ethernet or 100Base-TX Fast Ethernet cabling. This Ethernet port built N-Way protocol can detect or negotiate the transmission speed of the network automatically. Please use Category 5 cable to connect the Network Camera to a 100Mbps Fast Ethernet network switch or hub.

z LAN LED (green color)

This LED will be flashing while network accessing via Ethernet.

z Power / Wireless LED (orange color)

This LED is used to indicate whether DC power is on or not. In addition, this LED will be flashing while the wireless accessing of the Camera.

z DI/DO Connector

The Camera provides a terminal block with 4 pins of connectors for DI and DO. Please refer to the Appendix A in this manual for more information. The pin 1 is located at the right side of terminal block from rear view.

z Micro SD Card Slot

User can insert a micro SD card into this slot for event recording.

AirLive PoE-2600HD/ WN-2600HD User’s Manual

1.4 Mounting the Camera

Ceiling Mount

1. Fix the camera to L-type bracket with the two supplied screws

1. Introduction

2. Fix the bracket and camera to the ceiling using two holly wall anchors and screws

9 AirLive PoE-2600HD/

WN-2600HD User’s Manual

Wall Mount

1. Fix the L-type bracket to the wall using two holly wall anchors and screws

1. Introduction

2. Fix the camera to L-type bracket with the two supplied screws

AirLive PoE-2600HD/ WN-2600HD User’s Manual

1. Introduction

1.5 Install the Camera in LAN

1. Plug an Ethernet cable into the Camera

Connect an Ethernet cable to the LAN socket located on the camera’s rear and attach it to the network.

Ethernet

Cable

2. Connect the external power supply to Camera

Connect the attached power adapter to the DC power jack of the camera. Note: Use the power adapter, 12VDC, included in the package and connect it to wall outlet for AC power.

Power

Cable

Once you have installed the camera well and powered it on, the power LED will turn on later. The power LED turned on, it means the system is booting up successfully. Furthermore, if you have a proper network connection, and access to the camera, the LED will flash blue under wired mode.

11 AirLive PoE-2600HD/

WN-2600HD User’s Manual

2. Preparation

2.1 Search and Set up by IPWizard II

When you installed the Camera on a LAN environment, you have two easy ways to search your Cameras by IPWizard II or UPnP™ discovery. Here is the way to execute IPWizard II to discover Camera’s IP address and set up related parameter in a Camera.

2.1.1 Search

AirLive PoE-2600HD/ WN-2600HD User’s Manual

2. Preparation

When launch the IPWizard II, a searching window will pop up. IPWizard II is starting to search Network Cameras on the LAN. The existed devices will be listed as below.

13 AirLive PoE-2600HD/

WN-2600HD User’s Manual

2. Preparation

2.1.2 View

If IPWizard II finds network devices, View button will be available. Please select the device you want to view and click the View button. Then you could see the video from camera directly. Furthermore you could double click the left button of mouse to link to the network device by browser.

AirLive PoE-2600HD/ WN-2600HD User’s Manual

2. Preparation

2.1.3 LAN

In case you want to change the IP related parameters of wired interface, please select the device you want to configure and click the LAN button. Relative settings will be carried out as below.

15 AirLive PoE-2600HD/

WN-2600HD User’s Manual

2. Preparation

You could modify the relative settings of the selected device. Click “<<” button will quit the LAN setting procedure and click “>>” button will move to next page as below.

AirLive PoE-2600HD/ WN-2600HD User’s Manual

2. Preparation

In case, you do not want to change username and/or password, then just click “Submit” button to perform your setting accordingly. Click “<<” button will go back to previous page. If you like to change username and/or password of the device, just click the check button. Then, the related fields will show up as below.

After keying in new username and password, click “Submit” button to perform your setting accordingly. Click “<<” button will go back to previous page.

17 AirLive PoE-2600HD/

WN-2600HD User’s Manual

2.1.4 Wireless (WN-2600HD Only)

2. Preparation

In case you want to change the IP related parameters of wireless interface, please select the device you want to configure and click the WIRELESS button. Relative settings will be carried out as above.

AirLive PoE-2600HD/ WN-2600HD User’s Manual

Click SSID to select your wireless AP or router and key in WEP or WPA key.

2. Preparation

Click >> to next step:

19 AirLive PoE-2600HD/

WN-2600HD User’s Manual

2. Preparation

Make sure wireless setting and then submit it.

AirLive PoE-2600HD/ WN-2600HD User’s Manual

2. Preparation

Click OK to confirm these parameters, then IPWizard II will start to configure this camera with specified information.

21 AirLive PoE-2600HD/

WN-2600HD User’s Manual

2. Preparation

Once this step finished, IPWizard II will prompt you to unplug the Ethernet cable to activate wireless access. Then IPWizard II will prompt you to test wireless setting or finish wireless procedure as below.

AirLive PoE-2600HD/ WN-2600HD User’s Manual

2. Preparation

2.2 UPnP of Windows® XP, Vista or 7

UPnP™ is short for Universal Plug and Play, which is a networking architecture that provides compatibility among networking equipment, software, and peripherals. This device is an UPnP enabled device. If the operating system, Windows XP, Vista or 7, of your PC is UPnP enabled, the Network Camera will be very easy to be found.

Please refer to Appendix J to enable UPnP settings only if your operating system of PC is running Windows XP.

Note: Windows 2000 does not support UPnP feature.

To discover your device, go to your Desktop and click My Network Places.

Click the targeted Device. Then Internet Explorer will connect to this Network Camera automatically.

2.3 Install the Device behind a NAT Router

Once installed, the device is accessible on your LAN. To access the device from the Internet you must configure your broadband router to allow incoming data traffic to the device. If the device is installed on the LAN with a router, then it may get a dynamic IP address from the DHCP server. However, if the device wants to be accessed from the WAN, its IP address needs to be setup as fixed IP, also the port forwarding or Virtual Server function of router needs to be setup.

23 AirLive PoE-2600HD/

WN-2600HD User’s Manual

2. Preparation

However, if your NAT router supports UPnP feature, it can be very easy to achieve NAT traversal automatically. To do this, enable the NAT-traversal feature, which will attempt to automatically configure the router to allow access to the camera.

Installing the device with an UPnP router on your network is an easy 3–step procedure:

(1) Enable UPnP option of your NAT router　 (2) Enable UPnP NAT traversal option of the Network Camera (default)　 (3) Access your Network Camera by DIPS　

(1) Enable UPnP option of your NAT router

To use UPnP IGD function (NAT traversal), you need to make sure the UPnP function is enabled in your router. Most new home routers should support this function. Some of routers are default enable and others are not. Please check user’s manual of your NAT router for detail.

(2) Enable UPnP NAT traversal option of the Network Camera

Refer to Setting Î Network Î UPnP page for detail NAT traversal setting. Note that this option is default enabled.

(3) Access your Network Camera by DIPS Refer to Setting Î System Î System page for detail DIPS information.

2.4 Access the Device from the Internet Explorer for the First

Time

1. Start the web browser on the computer and type the IP address of the Camera you want

to monitor as below:

The Login Window of the Camera is prompted:

AirLive PoE-2600HD/ WN-2600HD User’s Manual

2. Preparation

2. Type in your login name and password under “USERNAME” and “PASSWORD” textbox.

For the first time use (default value), input the

User Name: admin Password: airlive

That’s, type in “admin” on the “USERNAME” and “airlive” on the “PASSWORD”. Click “OK” button to start the main menu.

3. According your browser’s security setting, the IE Web Page may prompt the “Security

Warning” window. If so, select “Yes” to install and run the ActiveX control into your PC. Otherwise, the system will load the ActiveX silently.

25 AirLive PoE-2600HD/

WN-2600HD User’s Manual

2. Preparation

4. After the ActiveX control was installed and ran, the first image will be displayed.

2.5 Logging in as an User

If you log in the Camera as an ordinary User, “Setting” function will be not accessible.

2.6 Logging in as an Administrator

If you log in the Camera as the Administrator, you can perform all the settings provided by the device.

AirLive PoE-2600HD/ WN-2600HD User’s Manual

+ 82 hidden pages