AirLive OD-2025PHD User Manual

OD-2025HD /OD-2025PHD

2-MegaPixel Outdoor 30fps 25 meter IR IPCAM / 2-MegaPixel Outdoor 30fps 25 meter IR IPCAM

Passive PoE

User’s Manual

AirLive OD-2025HD

/OD-2025PHD User’s Manual

Owner's Record

The model and serial numbers are located at the bottom of device. Record these numbers in the spaces provided below. Refer to these numbers whenever you call upon your dealer regarding this product.

Model No. ____________________

Serial No. ____________________

To prevent fire or shock hazard, do not expose the unit to rain or moisture. For AC Adaptor to avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only.

AirLive OD-2025HD

/OD-2025PHD User’s Manual

Notice: The changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

For customers in the U.S.A.

This equipment has been tested and found to comply with the limits for a digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

– Reorient or relocate the receiving antenna. – Increase the separation between the equipment and receiver. – Connect the equipment into an outlet on a circuit different from that to which the receiver

is connected.

– Consult the dealer or an experienced radio/TV technician for help.

You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment.

The shielded interface cable recommended in this manual must be used with this equipment in order to comply with the limits for a digital device pursuant to Subpart B of Part 15 of FCC Rules.

Declaration of Conformity

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may

cause undesired operation.

AirLive OD-2025HD /OD-2025PHD User’s Manual

IMPORTANT NOTE: To comply with the FCC RF exposure compliance requirements, no change to the antenna or the device is permitted. Any change to the antenna or the device could result in the device exceeding the RF exposure requirements and void user’s authority to operate the device.

NOTICE TO USERS

© 2006~11 All rights reserved. This manual or the software described herein, in whole or in part, may not be reproduced, translated or reduced to any machine readable form without prior written approval.

WE PROVIDES NO WARRANTY WITH REGARD TO THIS MANUAL, THE SOFTWARE OR OTHER INFORMATION CONTAINED HEREIN AND HEREBY EXPRESSLY DISCLAIMS ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE WITH REGARD TO THIS MANUAL, THE SOFTWARE OR SUCH OTHER INFORMATION. IN NO EVENT SHALL WE BE LIABLE FOR ANY INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES, WHETHER BASED ON TORT, CONTRACT, OR OTHERWISE, ARISING OUT OF OR IN CONNECTION WITH THIS MANUAL, THE SOFTWARE OR OTHER INFORMATION CONTAINED HEREIN OR THE USE THEREOF.

We reserve the right to make any modification to this manual or the information contained herein at any time without notice. The software described herein may also be governed by the terms of a separate user license agreement.

AirLive OD-2025HD

iii

/OD-2025PHD User’s Manual

Table of Contents

1. Introduction.................................................................................................................1

1.1 Overview..............................................................................................................1

1.2 Package Contents ...............................................................................................3

1.3 Connections.........................................................................................................4

1.4 Passive PoE Installation (For OD-2025PHD Only) ..............................................7

1.5 Mounting the Camera ..........................................................................................8

2. Preparation..................................................................................................................9

2.1 Search and Set up by IPWizard II........................................................................9

2.1.1 Search .......................................................................................................9

2.1.2 View......................................................................................................... 11

2.1.3 LAN .........................................................................................................12

2.2 UPnP of Windows® XP, Vista or 7.....................................................................15

2.3 Install the Device behind a NAT Router .............................................................16

2.4 Access the Device from the Internet Explorer for the First Time........................17

2.5 Logging in as an User........................................................................................18

2.6 Logging in as an Administrator ..........................................................................18

3. Operating the Network Camera ...............................................................................19

4. Administrating the Device........................................................................................25

4.1 Network: Configure Network Settings ................................................................26

4.1.1 Network ...................................................................................................26

4.1.2 HTTPS.....................................................................................................27

4.1.3 DDNS Service .........................................................................................28

4.1.4 PPPoE.....................................................................................................30

4.1.5 Streaming ................................................................................................32

4.1.6 UPnP .......................................................................................................33

4.1.7 Bonjour ....................................................................................................34

4.1.8 ONVIF......................................................................................................35

4.1.9 IP Filter ....................................................................................................36

4.1.10 IP Notification ........................................................................................37

4.2 Camera: Adjust Camera Parameters .................................................................40

4.2.1 Picture .....................................................................................................40

4.2.2 Privacy Mask ...........................................................................................42

4.2.3 PTZ Setting..............................................................................................43

4.2.4 Preset Setting ..........................................................................................44

4.2.5 Tour Setting .............................................................................................45

4.3 System: Configure and Maintain System...........................................................46

i AirLive OD-2025HD

/OD-2025PHD User’s Manual

Table of Contents

4.3.1 System ....................................................................................................46

4.3.2 Date & Time.............................................................................................47

4.3.3 Maintenance ............................................................................................49

4.4 Video: Configure Profile.....................................................................................51

4.4.1 Common..................................................................................................51

4.4.2 Video Profile ............................................................................................52

4.4.3 ROI ..........................................................................................................53

4.5 Audio: Audio Parameters ...................................................................................54

4.6 User: Manage User Name, Password and Login Privilege ................................55

4.7 E-Mail: Setup E-Mail Configuration....................................................................56

4.8 Object Detection: Setup Object Detection .........................................................57

4.9 Event Server: Setup FTP/TCP/HTTP/SAMBA Server Configuration .................58

4.11.1 FTP Server ............................................................................................58

4.11.2 TCP Server............................................................................................60

4.11.3 HTTP Server..........................................................................................61

4.11.4 SAMBA Server ......................................................................................62

4.10 Event Schedule: Configure the Event Schedule ..............................................63

4.12.1 Setting ...................................................................................................63

4.12.2 Record...................................................................................................68

5. Appendix....................................................................................................................69

Appendix A: Alarm I/O Connector ............................................................................69

Appendix B: Troubleshooting & Frequently Asked Questions..................................71

Appendix C: PING IP Address .................................................................................76

Appendix D: Bandwidth Estimation..........................................................................77

Appendix E: Specifications ......................................................................................78

Appendix F: Configure Port Forwarding Manually ...................................................80

Appendix G: DDNS Application ...............................................................................83

Appendix H: Power Line Frequency ........................................................................89

Appendix I: 3GPP ....................................................................................................91

Appendix J: Enable UPnP of Windows XP ..............................................................92

AirLive OD-2025HD /OD-2025PHD User’s Manual

1. Introduction

Introduction 1.

* The image in this user’s manual is for reference only; the actual color is based on real product.

1.1 Overview

This user’s guide explains how to operate this camera from a computer. User should read this manual completely and carefully before you operate the device.

The AirLive OD-2025HD/OD-2025PHD are high-end 2.0 MegaPixel (MP) network camera which designs for professional outdoor surveillance and security applications. This 2.0MP IP camera offers much improvements in image quality when compares to conventional surveillance cameras. Users are able to view live video streaming over the Internet, and it is only one of benefits for using AirLive IP Camera.

It is also designed to offer high-performance surveillance and the AirLive OD-2025HD equipped with PoE port which allows power and data to be transmitted via a single Ethernet cable. This useful function provides an easier installation, lower cabling costs and allows placement of AirLive PoE cameras in locations without access to electrical source. The AirLive OD-2025PHD supports 12V Passive POE which can not only has the

/OD-2025PHD User’s Manual

AirLive OD-2025HD

1. Introduction

advantage of the easier installation, lower cabling cost, but also provides low voltage consumption. This feature will greatly help installing the OD-2025PHD in the environment where power is an issue.

With the IP-66 waterproof housing, AirLive OD-2025HD/OD-2025PHD suits for environments such as stairs, main entrance, street, and basement. The device is accessible via the LAN or Internet connection. Connect your device directly to a local area network or xDSL modem, and with Microsoft® Internet Explorer you get instant, on demand video streams. Within minutes you can set up the device to capture a video sequence to a PC. The live video can be uploaded to a website for the world to see.

Note: AirLive OD-2025PHD uses 12V passive PoE. It is not compatible with 802.3af or

802.3at PoE switch. Please do not connect this IP camera to PoE switch, or the IP camera might be damaged.

Features

z 2.0 Mega CMOS H.264 IP Camera z Up to 1920 x 1080@30fps z Viewing the Video via 3/3.5G Mobile Phone z Support 802.3af Power over Ethernet z IP-66 Weatherproof Housing for most of Environments z With High Illuminate IR LED, Project up to 25 Meters z Support H.264, MPEG, MJPEG z Compatible with ONVIF standard z Support Two-Way Audio z Support Samba Server z Support Cam Pro Express 64 Channels

Minimum System Requirements

z Microsoft Internet Explorer 6.0 or later z Microsoft Media Player 11.0 or later (to playback recorded file) z VGA Monitor resolution 1280 x 1024 or higher z Pentium-4 3.6 GHz or higher z Memory Size: 1GB or more z Windows XP, Vista, 7

AirLive OD-2025HD /OD-2025PHD User’s Manual

1.2 Package Contents

User can find the following items in the package:

Item Descriptions

1. Introduction

1. OD-2025HD or OD-2025PHD is the main element of the product.

2. Wall mount

3. Wall mount stand

2. Screws x 3

3. Power Adapter

dedicates 12V DC electric power output to Network Camera.

4. User’s Manual CD provides installation software, application program, important information and instructions for operating the Network Camera.

/OD-2025PHD User’s Manual

AirLive OD-2025HD

1. Introduction

5. Quick Start Guide provides important information and instructions for installing this device.

6. PoE 1P: passive PoE injector (OD-2025HD only).

Note: Using a power supply with a different voltage than the one included with the Network Camera will cause damage and void the warranty for this product.

1.3 Connections

OD-2025HD

AirLive OD-2025HD /OD-2025PHD User’s Manual

OD-2025PHD

1. Introduction

1. RJ45 LAN socket: Connect to PC or Hub/Switch.

For connections to 10Base-T Ethernet or 100Base-TX Fast Ethernet cabling. This Ethernet port built N-Way protocol can detect or negotiate the transmission speed of the network automatically. Please use Category 5 cable to connect the Network Camera to a 100Mbps Fast Ethernet network switch or hub.

In the LAN socket, there are two LEDs embedded:

LAN LED (green color) This LED will be flashing while network accessing via Ethernet.

Power (orange color) This LED is used to indicate whether DC power is on or not. In addition, this LED will be flashing while the wireless accessing of the Camera.

2. DI/DO connector:

DI/ DO: Connect to sensor in and alarm out devices

Cable for I/O connectors:

Name Cable Color Function

12VDC Brown/White DC 12V (50mA maximum) GND Blue/White GND NC Purple/White Do not connect NC Gray Do not connect DI Green/White Digital signal input

/OD-2025PHD User’s Manual

AirLive OD-2025HD

1. Introduction

DO Orange/White Digital signal output

3. Factory Default Reset

This button is used to restore the all factory default settings. Sometimes restarting the device will make the system back to a normal state. However, if the system still got problems after restart, user can restore the factory default settings and install it again.

Restore the device:

(i) Press the button down continuously. (ii) Hold the button at least 5s seconds and release it. Then the device has been

restored to default settings and reboot again.

Note: Restoring the factory default setting will lose the all previous settings included IP address forever. User needs to run the IPWizard II program to search the device and configure it to let the device work properly again.

4. DC-in Jack

The input power is 12VDC. Note that supply the power to the Network Camera with the power adapter included in package.

5. MIC in (audio in)

Connect a microphone to the network camera.

6. Line out (audio out)

Connect a loud speaker to the network camera. This function is for voice alerting and two-way audio.

7. BNC Connector

The composite video format will be sent out through this connector. User might connect the IP Camera to a monitor or DVR via this connector.

AirLive OD-2025HD /OD-2025PHD User’s Manual

1.4 Passive PoE Installation (For OD-2025PHD Only)

1. Introduction

1. Connect the cable from the switch to the LAN port on the POE-1P

2. Connect the cable from the IP camera to the POE port, please note, for delivering the power properly, this should be a 4 twisted pair cable.

3. Plug the 12DC adapter to the DC phone jack.

/OD-2025PHD User’s Manual

AirLive OD-2025HD

1.5 Mounting the Camera

Ceiling Mount

Fix the camera with bundle wall mount kit as below.

Install the Camera in LAN

1. Plug an Ethernet cable into the Camera

Connect an Ethernet cable to the LAN socket and attach it into the network.

2. Connect the external power supply to Camera

1. Introduction

Connect the attached power adapter to the DC power jack of the camera. Note: Use the power adapter, 12VDC, included in the package and connect it to wall outlet for AC power.

Once you have installed the camera well and powered it on, the power LED (orange) will turn on later. The power LED turned on, it means the system is booting up successfully. Furthermore, if you have a proper network connection, and access to the camera, the LAN LED (green) will flash.

AirLive OD-2025HD /OD-2025PHD User’s Manual

2. Preparation

Preparation 2.

2.1 Search and Set up by IPWizard II

When you installed the Camera on a LAN environment, you have two easy ways to search your Cameras by IPWizard II or UPnP™ discovery. Here is the way to execute IPWizard II to discover Camera’s IP address and set up related parameter in a Camera.

2.1.1 Search

/OD-2025PHD User’s Manual

AirLive OD-2025HD

2. Preparation

When launch the IPWizard II, a searching window will pop up. IPWizard II is starting to search Network Cameras on the LAN. The existed devices will be listed as below.

AirLive OD-2025HD /OD-2025PHD User’s Manual

2. Preparation

2.1.2 View

If IPWizard II finds network devices, View button will be available. Please select the device you want to view and click the View button. Then you could see the video from camera directly. Furthermore you could double click the left button of mouse to link to the network device by browser.

AirLive OD-2025HD

/OD-2025PHD User’s Manual

2. Preparation

2.1.3 LAN

In case you want to change the IP related parameters of wired interface, please select the device you want to configure and click the LAN button. Relative settings will be carried out as below.

AirLive OD-2025HD /OD-2025PHD User’s Manual

2. Preparation

You could modify the relative settings of the selected device. Click “<<” button will quit the LAN setting procedure and click “>>” button will move to next page as below.

AirLive OD-2025HD

/OD-2025PHD User’s Manual

2. Preparation

In case, you do not want to change username and/or password, then just click “Submit” button to perform your setting accordingly. Click “<<” button will go back to previous page. If you like to change username and/or password of the device, just click the check button. Then, the related fields will show up as below.

After keying in new username and password, click “Submit” button to perform your setting accordingly. Click “<<” button will go back to previous page.

AirLive OD-2025HD /OD-2025PHD User’s Manual

2. Preparation

2.2 UPnP of Windows® XP, Vista or 7

UPnP™ is short for Universal Plug and Play, which is a networking architecture that provides compatibility among networking equipment, software, and peripherals. This device is an UPnP enabled device. If the operating system, Windows XP, Vista or 7, of your PC is UPnP enabled, the Network Camera will be very easy to be found.

Please refer to Appendix J to enable UPnP settings only if your operating system of PC is running Windows XP.

Note: Windows 2000 does not support UPnP feature.

To discover your device, go to your Desktop and click My Network Places.

Click the targeted Device. Then Internet Explorer will connect to this Network Camera automatically.

/OD-2025PHD User’s Manual

AirLive OD-2025HD

2. Preparation

2.3 Install the Device behind a NAT Router

Once installed, the device is accessible on your LAN. To access the device from the Internet you must configure your broadband router to allow incoming data traffic to the device. If the device is installed on the LAN with a router, then it may get a dynamic IP address from the DHCP server. However, if the device wants to be accessed from the WAN, its IP address needs to be setup as fixed IP, also the port forwarding or Virtual Server function of router needs to be setup. However, if your NAT router supports UPnP feature, it can be very easy to achieve NAT traversal automatically. To do this, enable the NAT-traversal feature, which will attempt to automatically configure the router to allow access to the camera.

Installing the device with an UPnP router on your network is an easy 3–step procedure:

(1) Enabl　 e UPnP option of your NAT router (2) Enable UPnP NAT traversal option of the Network Camera (default)　 (3) Access your Network Camera by DIPS　

(1) Enable UPnP option of your NAT router

To use UPnP IGD function (NAT traversal), you need to make sure the UPnP function is enabled in your router. Most new home routers should support this function. Some of routers are default enable and others are not. Please check user’s manual of your NAT router for detail.

(2) Enable UPnP NAT traversal option of the Network Camera

Refer to Setting Î Network Î UPnP page for detail NAT traversal setting. Note that this option is default enabled.

(3) Access your Network Camera by DIPS

Refer to Setting Î System Î System page for detail DIPS information.

AirLive OD-2025HD /OD-2025PHD User’s Manual

2. Preparation

2.4 Access the Device from the Internet Explorer for the First

Time

1. Start the web browser on the computer and type the IP address of the Camera you want

to monitor as below:

The Login Window of the Camera is prompted:

2. Type in your login name and password under “USERNAME” and “PASSWORD” textbox.

For the first time use (default value), input the

User Name: admin Password: airlive

That’s, type in “admin” on the “USERNAME” and “airlive” on the “PASSWORD”. Click “OK” button to start the main menu.

3. According your browser’s security setting, the IE Web Page may prompt the “Security

Warning” window. If so, select “Yes” to install and run the ActiveX control into your PC. Otherwise, the system will load the ActiveX silently.

/OD-2025PHD User’s Manual

AirLive OD-2025HD

2. Preparation

4. After the ActiveX control was installed and ran, the first image will be displayed.

2.5 Logging in as an User

If you log in the Camera as an ordinary User, “Setting” function will be not accessible.

2.6 Logging in as an Administrator

If you log in the Camera as the Administrator, you can perform all the settings provided by the device.

AirLive OD-2025HD /OD-2025PHD User’s Manual

3. Operating the Network Camera

3. Operating the

Network Camera

Start-up screen will be as follow no matter an ordinary users or an administrator.

ActiveX Control

Monitor Image

Full Screen

Section

Monitor Image Section

The image shot by the device is shown here. The date and time are displayed at the top of the window.

Video Profile

The device supports multi-profile function for H.264, MEPG4 and JPEG simultaneously. User can chose the proper and/or preferred profile which is listed here.

Streaming Protocol

User can select proper streaming protocol according to networking environment.

Language

The device could provide multiple languages to meet customer’s requirement.

/OD-2025PHD User’s Manual

AirLive OD-2025HD

3. Operating the Network Camera

2-Way Audio

The device supports 2-way audio function. User can chose to enable or disable this function by toggling the icon below.

: Disable audio uploading function.

: Enable audio uploading function.

Full Screen

Enlarge video to full screen display.

: Enlarge video to full screen display. Press “ESC” key to disable this function.

PTZ Control

Click to display the following control panel:

Camera direction

Camera

eed

Preset

Go tour

Tour

Auto pan

z Camera direction:

Control camera up/down/left/right and home position.

AirLive OD-2025HD /OD-2025PHD User’s Manual

3. Operating the Network Camera

z Camera speed:

Choose the speed of Pan and Tilt.

z Preset:

Add/Update the preset positions or go to one of these positions.

z Tour:

Select one of the camera tours. Camera tour is comprised by series of preset locations.

z Go tour:

Execute the selected camera tour.

z Auto Pan:

Execute the auto pan of camera. While auto pan is running, the camera will swing the camera automatically. Note that the speed of auto pan is fixed and can not be adjustable.

ActiveX Control

The plug-in ActiveX control supports a lot of functions by clicking the left mouse button. Note that this feature only supports on the ActiveX control within Microsfoft® Internet Explorer.

On the ActiveX control icon, click the LeftMouseButton, then a menu pop-up. This menu provides features that are unique to the ActiveX control. These features include:

• “Digital Zoom”,

• “Snapshot”,

• “Record”,

• “Volume”,

• “About”

AirLive OD-2025HD

/OD-2025PHD User’s Manual

3. Operating the Network Camera

z Digital Zoom

Click Digital Zoom to active this function as above. User can drag or scale the box over the video to adjust zoom ratio and position.

AirLive OD-2025HD /OD-2025PHD User’s Manual

z Snapshot

3. Operating the Network Camera

Click Snapshot to activate this function. Press Snapshot button to take a picture. The image file is saved as JPEG format into your local PC. Select Browser, the pop-up window to select the save path and file name prefix, select OK to continue.

If you like to retrieve the saved image, select the file to display the saved image by using any one of graph editing tools.

z Record

Click Record to activate this function. Press Record button to start recording. The video file is saved as ASF format into your local PC. While you want to stop it, press Stop to stop recording. Select Browser, the pop-up window to select the save path and file name prefix, select OK to continue.

/OD-2025PHD User’s Manual

AirLive OD-2025HD

3. Operating the Network Camera

After stop recording, list the files, this file is named as Video_yyyymmddhhmmss.avi The ASF files can be display by the standard Windows Media Player, but it needs the DixectX 9.0 or later version to be installed.

z Volume

Click Volume to activate this function. There are two control bars for speaker and microphone volume respectively. Scroll these control bars to adjust the audio attribute. Check the volume mute will mute the speaker output.

z About

Click About to show this ActiveX information.

AirLive OD-2025HD /OD-2025PHD User’s Manual

+ 71 hidden pages