Page 1
Quick Installation Guide
24-Port 10/100/1000Mbps
Green Switch
Model# AGSW2400
Ver. 1A
Page 2
Trademarks
Copyright © 2011 Airlink101®
Airlink101® is a registered trademark. All other trademarks
belong to their respective proprietors.
Copyright Statement
No part of this publication may be reproduced in any form or
by any means or used to make any derivative such as
translation, transformation, or adaptation without permission
from Phoebe Micro, Inc.
Preface
FCC Warning
This device has been tested and found to comply with limits
for a Class a digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment
is operated in a commercial environment. This equipment
generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the user’s
manual, may cause interference in which case the user will
be required to correct the interference at his own expense.
CE Mark Warning
This is a Class A product. In a domestic environment, this
product may cause radio interference in which case the
user may be required to take adequate measures.
1
Page 3
1 Introduction
Congratulations on your purchase of the 24-Port
10/100/1000Mbps Green Switch! It is an easy-installed
network switch which helps you to extend your network
structure quickly and reliably.
Purpose
This Quick Installation Guide tells you how to install your
Switch and how to connect it to your Ethernet network.
Terms/Usage
In this manual, the term “Switch” (first letter upper case)
refers to your 24-Port 10/100/10000Mbps Green Switch,
and “switch” (first letter lower case) refers to other Ethernet
switches.
1.1 Hardware Interface
• 24-Port 10/100/1000Mbps auto-negotiation RJ45 Ports
• All ports support auto MDI/MDIX, no need to use
cross-over cables
2
Page 4
1.2 Panel
1.2.1 Front Panel
The front panel of the Switch consists of LED indicators, and
24 10/100/1000Mbps ports. The figure below shows the front
panel of the Switch.
Figure 1-1 Front Panel view of the Switch
• 10/100/1000Mbps Ports (Port 1~24): These ports support
10/100/1000Mbps, and can operate in Half/Full Duplex
transfer modes. These ports also support automatic
MDI/MDI-X crossover detection, giving true “plug and
play” capability.
• LED Indicators: Comprehensive LED indicators display
the status of the switch and the network (see Section
1.2.3).
3
Page 5
1.2.2 Rear Panel
Figure 1-2 Rear Panel view of the Switch
• AC Power Connector: Supports AC 100~240V, 50~60Hz.
NOTICE:
Do not cover or put anything on and surrounding the switch
while the Switch is operating.
1.2.3 LED indicators information
The front panel LEDs provide instant status feedback and
help monitoring and troubleshooting when needed.
Figure 1-3 Front Panel view of the switch
4
Page 6
• POWER: Power Indicator
Status
LED Color
Solid Blinking Off
The Switch is
POWER Green
power-on
N/A No power
• Port 1~24 10/100/1000Mbps Status LEDs
Status
LED Color
Solid Blinking Off
The
respective
LINK/
ACT
10/100M
LED Color
LINK/
ACT
1000M
Green
Green
port is
successfully
connected to
the
10/100Mbps
Ethernet
network
Solid Blinking Off
The
respective
port is
connected to
the 1000Mbps
Ethernet
The port is
transmitting or
receiving data
at
10/100Mbps
Status
The port is
transmitting or
receiving data
at above
100Mbps
No link
No link
network
5
Page 7
1.3 Technical Specifications
Standards
• IEEE 802.3 10BASE–T, IEEE 802.3u 100BASE–TX,
IEEE802.3ab 1000BASE-T Gbit and IEEE 802.3x Flow
Control
Network Cables
• Ethernet (10Base-T): Cables: 2-pair UTP Cat. 3, 4, 5,
Twisted Pair (UTP). Up to 100m
• Fast and Giga Ethernet (100/1000Base-T): 2-pair UTP
Cat. 5, Twisted Pair (UTP). Up to 100m
Ports
• 24 x 10/100/1000Mbps Auto-Negotiation RJ45 Port
Access Method
• CSMA/CD
Transmission Method
• Store and Forward
MAC Address Table
• 16K
Jumbo Frame
• 9216-byte jumbo packet length forwarding at wire speed
6
Page 8
Data Transfer Rate**
• Ethernet: 10/20Mbps – Half/Full-Duplex
• Fast Ethernet: 100/200Mbps – Half/Full Duplex
• Giga Ethernet 1000/2000Mbps – Half/Full Duplex
Physical and Environmental
• Power Input: 100~240V AC, 50~60Hz
• Operation Temperature: 0 °C ~ 40°C
• Storage Temperature: -20°C ~ 70°C
• Humidity: 5% ~ 90% RH, non-condensing
7
Page 9
2 Installing the Switch
The site where you place the switch may greatly affect its
performance. When installing, take the following into your
consideration.
2.1 Installation
Follow the guidelines below to install the Switch:
Install the Switch in a fairly cool and dry place. See the
Technical Specifications for the acceptable temperature and
humidity operating ranges. Install the Switch on a sturdy,
level surface that can support its weight. Connect the power
cord to the Switch and the power outlet. The distance is no
more than 182cm.
Leave at least 10cm (about 4 inches) of space at the front
and rear of the Switch for ventilation.
2.2 Desktop or Shelf Installation
When installing the Switch on the desktop or shelf, please
attach the rubber feet to the Switch. Peel off the protective
paper on the pads and attach them on the bottom of the
Switch (one at each corner).
8
Page 10
2.3 Rack Installation
The Switch is rack-mountable and can be installed on an EIA
13-inch equipment rack. To do this, first install the mounting
brackets on the Switch’s side panels (one on each side),
secure them with the included screws, and then use the
screws provided with the equipment rack to mount the
Switch.
2.4 Power on the Switch
The Switch has a universal power supply ranging from 100V
to 240V AC, 50 ~ 60Hz power source. The AC power
connector is located at the rear of the unit. The switch’s
power supply will adjust to the local power source
automatically.
9
Page 11
3 Connecting the Switch
This section describes how to connect the Switch to your
10/100/1000Mbps Ethernet network.
3.1 Connection
Your network device (i.e. computer, switch, IP Camera, VoIP)
can be connected to any port of the Switch via a two-pair
UTP Category 5 Cable. If the LED indicators do not light up
after making a proper connection, check your network device,
the cable, the Switch conditions and connections.
10
Page 12
4 Technical Support
E-mail: support@airlink101.com
Toll-Free: 1-888-746-3238*
Web Site: www.airlink101.com
* Free Voice Technical Support is only available within the hardware warranty
(1-Year Limited Warranty from the date of purchase). Customer is required to
provide invoice as purchase evidence.
**Network conditions and environmental factors as well as network overhead can
lower actual data throughput rate.
Copyright © 2011 AirLink101
AirLink101
that are identified as trademarks and/or service marks are, unless noted
® logo, specific product designations, and all other words and logos
®. All rights reserved. AirLink101, the stylized
otherwise, the trademarks and service marks of AirLink101
service names are the property of their respective holders. AirLink101 products
are protected under numerous U.S. and foreign patents and pending applications,
mask work rights, and copyrights.
11
®. All other product or
Loading...