AirLink AKVM-S32 Quick Start Manual

Ver. 1A

Quick Installation Guide

Model # AKVM-S32

Step 2 Connect the shared keyboard, monitor , and

mouse to the main KVM unit. See Fig. 1.1

Section 3

Operations

There are two methods to select a specific computer:
Using the push button or the hotkey sequence.

Push Button

Section 1

Introduction

The AKVM-S32 is a 2-port PS/2 type KVM switch that
comes with two sets of 3-in-1 combo KVM cables. It
enables users to access, control, boot, and reboot two

1

computers using only one keyboard, video monitor, and
mouse. Its slim-sized design offers more portability and
convenience to users than conventional KVM switches.

Section 2

Installation

Before connecting any cable, please make sure all of your
computers and their peripherals have been powered off.
Otherwise, the KVM switch may not be set up properly.

Fig 1.1

Step 3 Connect each of your computers to the KVM

switch using the provided 3-in-1 combo KVM cables.
See Fig.1.2

KVM Side

Fig 1.2

Y ou can use individual standard keyboard, mouse
and video cables to extend the cable distance, but
depending on the type of cables you use, the
maximum cable distance is limited to 5 ~ 7 meters
(15.5 ~ 23 feet).

Step 4 Power up the connected computers one by

one. After the computers are powered up, the
keyboard and mouse will be recognized and you can
begin operating the KVM switch.

PC Side

The push button lets you directly switch between the
computers. Simply press the button on the KVM unit
to select the computer.

Hotkey Sequence

The hotkey sequence consists of three specific
keystrokes pressd on the keyboard.

Hotkey sequence = ScrLk + ScrLk + Command key
The two consecutive ScrLk key should be pressed
within 2 seconds and the following command key(s)
should also be pressed within 2 seconds. Otherwise,
the hotkey sequence will not be validated.

For detailed Hotkey sequences and their correspond­ing functions, please refer to the Quick Reference
Chart on back.

Section 4

Technical Support

Email: [e-mail]
T oll Free: 1-888-746-3238

Step 1 Make sure all the computers that are to be

connected to the KVM switch and their peripherals
are powered-off. If not, power them off before you
proceed with the following steps.

Website: www.airlink101.com

Continue on Back

Quick Reference Chart

Command

Select PC

Next lower channel ScrLk + ScrLk + (up arrow)

Next higher channel ScrLk + ScrLk + (down arrow)

Previous PC channel ScrLk + ScrLk + (Backspace)

Reset KVM

Autoscan

Stop Autoscan

Autoscan with
programmable delay
time

ScrLk + ScrLk + (channel #) Select the active channel

ScrLk + ScrLk + End

ScrLk + ScrLk + S

Any key on keyboard

ScrLk + ScrLk + (x)

Hotkeys Front-Panel Button Description

2

1

Select the lower channel

Press the push button to
rotate through the channel

Select the higher channel

Reset the KVM Switch

Autoscan through every connected channel

T erminate Autoscan activity

Autoscan with a user-defined delay time
within a range of 5 ~ 99 seconds

1: Press 1 or 2 for the for the channel #
2: x = 0 ~ 9

1 .. 10” ; 2 .. 20” ; 3 .. 30” ; 4 .. 40” ; 5 .. 50”

6 .. 60” ; 7 .. 70” ; 8 .. 80” ; 9 .. 90” ; 0 .. 99”

Copyright ©2006 AirLink101™ All rights reserved. AirLink101, the stylized AirLink101 logo, specific product designations, and all other words and logos that are identified as trademarks and/or service marks are, unless noted otherwise, the trademarks and service marks of AirLink101. All
other product or service names are the property of their respective holders. AirLink101 products are protected under numerous U.S. and foreign patents and pending applications, mask work rights, and copyrights.