Air King 9929 Owner's Manual

MODEL 3LA79A/9929A

TROUBLE SHOOTING GUIDE

TROUBLE PROBABLE CAUSE SOLUTION

Fan not working or • No power Make sure Unit is plugged in
Humidifier doesn’t Check that the Power Switch is On
turn on • Humidistat not set correctly Set Humidistat to higher humidity level

Water leaking • Base is overfilled Reduce water level in Base

Foul odor • Filter needs to be replaced Replace Filter

Filter discoloration • Mineral deposits in water Replace Filter
Water discoloration • Humidifier needs to be cleaned Follow Instructions in CLEANING section

Lights do not work:
Humidistat Light Off, • Humidity is not yet achieved in room Allow Humidifier to continue running

Power Light On
Power Light Off, • Room has reached desired Set Humidity Knob for more Humidity
Humidistat Light On Humidity level

No water show • No water in Unit Refill Unit

KEY PART NO. DESCRIPTION QTY.

1 2010598 Humidifier Top 1
2 02091220I Screw #8 x 1/2 PPH Type 30A ZP 15
3 02030008EG Motor/Control Box Assembly 1
4 2010588 Chassis 1
5 2010590 Drip Shield 1
6 2010591EG Base 1
7 2010592 Front Filter Holder 1
8 2010593 Rear Filter Holder 1
9 02010860S Lever 1
10 02010861 Spring 1
11 02010862 O-Ring 1
12 02010871 Plunger 1
13 2010844 Jug 1
14 2010597 Jug Top 1
15 2010596 Jug Lid 1
16 02010868S Water Distribution Block 1
17 02010869S Water Show Assembly 1
18 2010870 Filter 1
19 2011073 Blade 1
20 2011074 Basket 1
21 2069093 Tube 1/4” x 24 1/2” 1
22 2069094 Tube 1/4” x 15 1/2” 1
23 02091221I Screw #8 X 3/4” PTH Type 30A ZP 7
24 02098038 Castors 4
25 02010601 Handle 1
26 02010867S Impellor 1
27 02010866LS Lower Pump Housing 1
28 02010866US Upper Pump Housing 1

Rev. A 9/05 4 2084779

•Top of Humidifier not seated properly Make sure top is properly seated on Base
on Base (Unit is equipped with an
automatic shut off)

• Filter Holder not assembled properly Make sure Filter Holder is seated in place
or is missing (Unit is equipped with an
automatic shut off)

• Filter is old and dirty Replace Filter

• Base needs to be cleaned Follow Instructions in CLEANING section

• Whole Humidifier needs cleaning Follow Instructions in CLEANING section

• Hard water - Iron in water Use filtered or distilled water

• Some humidifier additives can cause
discoloration

• Hose not connected to Pump Connect Hose to Pump

• Hose not connected to Water Show Connect Hose to Water Show

1

2

3

4

16

21

19

2023

22

3

28

26
27

5

6

2

17

18

8

24

25

12

11
15

10

9

7

13

14

OPERATING INSTRUCTIONS & PARTS MANUAL

DIGITAL RECIRCULATING HUMIDIFIER

9 GALLON MODEL 3LA79A/9929A

READ AND SAVE THESE INSTRUCTIONS

READ CAREFULLY BEFORE ATTEMPTING TO ASSEMBLE, INSTALL, OPERATE OR MAINTAIN THE PRODUCT DESCRIBED.

PROTECT YOURSELF AND OTHERS BY OBSERVING ALL SAFETY INFORMATION. FAILURE TO COMPLY WITH

INSTRUCTIONS COULD RESULT IN PERSONAL INJURY AND/OR PROPERTY DAMAGE!

RETAIN INSTRUCTIONS FOR FUTURE REFERENCE.

DESCRIPTION

The AirKing 9 Gallon (34.1 liter) Humidifier features 3-Speed whisper
quiet operation. This unit is capable of humidifying up to 3200 sq. ft.
(355.6 sq. yards) and features a 7.5 ft. (2.3 m) 18/3 cord set.

SPECIFICATIONS

Motor....................................120V, 50/60 Hz

Blade diameter ....................9" (22.86 cm)

Speeds.................................3

Control .................................Rotary Switch

Approvals.............................UL/CUL Listed

MODEL
SPEED

RPM 1300 1100 900
Amps 0.590 0.500 0.450
Watts 62.8 58.8 49.8
dB A 61 59 53

3LA79A/9929A

HIGH MED LOW

GENERAL SAFETY INFORMATION

1. Make certain that the power source conforms to the electrical require­ments of the Humidifier.

2. The power cord is equipped with a three-prong grounded plug that
must be inserted into a matching receptacle. Under no circum­stances must the grounding prong be cut off the plug. Where a two­prong wall receptacle is encountered, it must be replaced with a
properly grounded three-prong receptacle installed in accordance
with the National Electrical Code (NEC) and all applicable local
codes and ordinances. This work must be done only by a qualified
electrician, using copper wire only.

WARNING: USE OF A THREE-PRONG TO TWO-PRONG ADAPTER
IS NOT RECOMMENDED. IMPROPER CONNECTION MAY CREATE
THE RISK OF ELECTROCUTION. USE OF SUCH ADAPTERS ARE
NOT PERMITTED IN CANADA.

WARNING: THIS PLUG IS A SAFETY FEATURE. TO REDUCE THE
RISK OF FIRE, ELECTRIC SHOCK AND PERSONAL INJUR Y , DO NOT
REMOVE, REPLACE, REPAIR OR TAMPER WITH THE ORIGINALLY
SUPPLIED PLUG. IF THE FAN DOES NOT FUNCTION PROPERLY, IT
MAY BE DUE TO THE SAFETY DEVICE INCORPORATED IN THIS
PLUG. RETURN TO AN AUTHORIZED SERVICE CENTER OR CALL
800-233-0268, MONDAY - FRIDAY , BETWEEN 8:00 AM AND 5:00 PM
EST. IF THE PLUG WARNING LABEL IS MISSING OR DAMAGED,
CALL THE TOLL FREE NUMBER FOR A REPLACEMENT LABEL.

3. Where possible, avoid the use of extension cords. If they must be

used, minimize the risk of overheating by ensuring that they are UL
listed and of the proper gage and length. Never use a single extension
cord to operate more than one Humidifier.

4. Do not insert fingers or foreign objects into the Humidifier. Do not block
or tamper with the Humidifier in any manner while it is in operation. Do
not touch the Humidifier while in operation or just after it has been
turned off, as some parts may be hot enough to cause injury.

5. Unplug power cord before filling or servicing the Humidifier.

DO NOT pour water into Grill. DO NOT spill water on Control Panel.

Water should only be poured into the Unit using the Jug.

Rev. A 9/05 1 2084779

WARNING: DO NOT DEPEND UPON THE ON-OFF SWITCH AS THE SOLE
MEANS OF DISCONNECTING POWER WHEN FILLING OR SERVICING
THE HUMIDIFIER. ALWAYS UNPLUG THE POWER CORD.

6. This Humidifier is intended for general use ONLY. It must NOT be

used in potentially dangerous locations such as flammable, explo­sive, chemical-laden or wet atmospheres.

WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,
DO NOT USE THIS HUMIDIFIER WITH ANY SOLID STATE SPEED
CONTROL DEVICE.

7. Always place the Humidifier is on a stable, flat, level surface when

operating, to avoid the chance of the Humidifier over tur ning. Locate
the Power Cord so the Humidifier or other objects are not resting on it.
Keep the Power Cord away from room traffic.

8. Always direct air flow away from walls and furniture. Excessive moisture
may cause damage.

9. Completely reassemble Humidifier, according to instructions, before
reconnecting to power supply.

10. Humidifiers require regular cleaning to maintain proper operating condi­tions. Refer to the CLEANING section for proper cleaning procedures.

NOTE: A few droplets of water may be present
in your Humidifier as a result of our quality
testing prior to packaging and shipment.

ASSEMBLY

CAUTION: DO NO T fill unit
before assembling.

1. Remove Water Jug then,

Upper Housing from base
of unit.

(Figure 1)

2. Lay base of unit on it’s side
so the bottom of the unit
is facing you.

Figure 2

Hole

Castor

Water Jug

Upper Housing

3. Fully insert the four Castors into
the holes in the bottom of the unit.

(Figure 2)

4. Replace Upper Housing, then Wa­ter Jug into unit.

Figure 1

Base

MODEL 3LA79A/9929A

Na

t

u

r

a

l

Ca

sc

a

MODEL 3LA79A/9929A

CAUTION: Do not pour water through the
Exhaust Grill on the Upper Housing. Doing
so may cause damage and personal injury .

CAUTION: • Unplug Unit when filling.

• Always place Humidifier on a firm level surface.
Locate the Power Cord so the Humidifier is
not resting on it, and is away from traffic.

• Be careful not to overfill.

• Do not pour water through Exhaust Grill,
doing so may cause damage and personal injury .

•Take extra care to prevent water spillage
that may damage furniture or flooring. The
manufacturer will not accept responsibility for
damage to property caused by water spillage.

• Always be sure the Power Knob is in the OFF
position when plugging Humidifier into a
grounded 120 volt AC wall outlet.

•To prevent risk of electrical shock and injury to
persons, do not plug Humidifier into electrical
outlet with wet hands.

1. It is recommended that all Humidifiers be cleaned prior to use. Please
read Cleaning Instructions for Base and Jug cleaning.

2. Use the convenient Carrying Handle found on the bottom of the
Water Jug to bring it to a faucet. The Water Jug features a ‘Quick
Fill/Quick Empty’ Spout. To fill, hold Jug upside down by the Handle.
Use thumb to press down Stopper Lever , and fill Jug. Fill the W ater
Jug with cool tap water. Never use hot water.

(Jug Holds 1-1/2 Gallons)

Carry Handle

(Figure 3)

Figure 3

Stopper Lever

Quick Fill /

Quick Empty

Spout

(Base Holds 3 Gallons)

Water Capacity of Unit is 4.5 Gallons

When the Jug is replaced back into the Base it will quickly
empty to fill Base.

NOTE: While carrying filled Water Jug bac k to the Humidifier , hold
the Handle with one hand, while supporting bottom of Water Jug
with other hand.

3. Place the Water Jug securely in the Base. If positioned
properly , water will quickly pour into Base and automatically stop
when reaching desired amount.

4. When gurgling noise stops lift up the Water Jug to see if it is
empty. Refill if empty. When the Unit is full, some water will re­main in the Jug.

5. Even though your Humidifier will produce approximately 9.0
gallons in a 24 hour period*, the water capacity (amount of water
the Humidifier will hold at one time) is 4.5 gallons.
(3 FULL Jugs).

OPERATION

1. Turn fan speed knob to desired speed.

-For fast humidification of a large room or house,

3

approximately 9 gallon per day.*

-For normal operation.

2

-For quiet, night time operation or after desired moisture

1

level is reached.

* Calculations based on ambient room conditions of 70° F
and 30% relative humidity in a room of average insulation.

The presence of water flow in the Water Show Window indicates
the circulation of water to the Filter.

The correct room humidity display will set itself 10 seconds after
the power cord is plugged into a 120 V outlet.

2. Push the humidity set button up or down, to adjust the
humidity to the desired level. The desired humidity range is
25% to 95%.

The desired humidity level is displayed in small numbers and the
correct room humidity % is displayed in large numbers.

Once the current room humidity level reaches the desired humid­ity level, the fan will turn off and the humidity indicator light will
come on. This light indicates that the humidifier is still on and will
again start when the current room humidity level falls below the
desired set level.

If the current room humidity drops below 25% or goes above
95%, the display will blink off and on until the current room
humidity is within the 30% to 90% range.

1

2

0

3

2

1

5

1. Fan Speed Knob

2. Humidity Set Button

3. Desired Humidity %

4. Current Room Humidity %
Humidity Indicator Light

5.

- Light comes on when desired humidity

(Figure 4)

Figure 4

▲

▼

3

Figure 5

4

level is the same or lower than current
room humidity while the speed knob is
in the on position.

FILTER CARE

The Filter inside your Humidifier plays a very important part in its
operation. In order to maintain peak performance, it is highly
recommended to use only AIRKING REPLACEMENT FILTERS.
Some imitation filters do not comply with AirKing’s quality standards,
resulting in decreased performance of your Humidifier.

CAUTION: To prevent electric shock, always turn Power
Control Knob to OFF position and unplug before servicing.

1. To replace the Evaporative Filter Pad, remove the Jug and Upper
Housing from the Base. Be careful not to let excess water
from pump spill onto furniture or flooring.

2. Remove Evaporative Filter Pad Holder from Base and inspect

Small Water Drip Holes for any blockage.

Filter Pad Holder

3. To open the Filter Holder apply outward pressure to the two
snaps and it will hinge open. Remove used Filter from Holder
and discard.

(Figure 7)

Snaps

Evaporative Filter Pad

Model 9930

4. Insert new Filter into Holder, snap closed, and reinstall Holder
into Base.

(Figure 7)

The Filter will only fit into the Holder one
way. Make sure the Rounded side of the Filter Holder is facing
outward. Replace Upper Housing, then Water Jug into Base.

5. To increase the life of your Filter P ad turn
Filter around (so the bottom of Filter is
now at the top).

6. Filter life may be extended by cleaning
the Filter in a 20% vinegar solution. To
clean Filter, mix one part undiluted vin­egar with four parts warm tap water. Soak the Filter in this
solution for 20 minutes, rinse Filter thoroughly with warm wa­ter to remove vinegar odor.

DO NOT FLA TTEN, SQUEEZE OR TWIST FIL TER WHEN CLEANING.

(Figure 6)

Figure 6

Drip Holes

Base

Figure 7

7. Discoloration of the Evaporative Pad is normal after
extended use. The discoloration is caused by mineral deposits
in the water, and the degree of discoloration will var y depending
upon the amount of mineral content in the water. When the Fil­ter surface area is thoroughly discolored, or you notice
reduced water usage, it is a good indicator that the Filter Pad
needs to be replaced. The Evaporative Pad should be

replaced at least once every season.

CLEANING

1. Regular cleaning is necessary to ensure proper and
efficient operation. The frequency of cleaning depends on
the amount of impurities which may be found in the water
or how often the Humidifier is in operation. In either in-

stance, it is recommended that the Humidifier be
cleaned at least once a week.

NOTE: Unscrew bottom of Water
Jug for easy cleaning.

(Figure 8)

Figure 8

CAUTION: Make sure bottom of
Jug is securely fastened to Jug
before reinstalling into Base.

2. TO

DESCALE BASE, JUG

AND DRIP SHIELD: Mix one

part undiluted white vinegar
with four parts warm tap wa­ter. Let vinegar solution
stand for 20 minutes then
wipe away any scale buildup
using a soft brush or cloth.

Do not use soap or deter­gents and never use an
abrasive cleaner.

3. TO

DISINFECT BASE, JUG

AND DRIP SHIELD: Fill Jug with 1 teaspoon of chlorine b leach

and 1 gallon of water. Let solution stand f or 20 minutes. Carefully
empty Jug and rinse well with water until bleach smell is gone.

4. Commercial "Descalers" and "Bacteriostats" are available at your
local home improvement center.

5. Do not operate Humidifier when there is still cleaner in the water.

OFF-SEASON STORAGE

1. Clean and dry Humidifier thoroughly per the CLEANING
section above. Do not leav e any water in the Unit when storing.

2. Dispose of the Evaporative Filter Pad. Do not store used
Evaporative Filter Pad in the Humidifier.

3. Place Humidifier back into its carton and store in a cool
dry place.

Rev. A 9/05 3 2084779Rev. A 9/05 2 2084779