Airgo Networks AGN0901AP0100, AGN1223AR0300 User Manual

F5D8230-4 user draft.doc Page 1 of 89

[insert title page per branding standard]
Wireless Pre-N Router

Share your high-speed Internet connection without cables [this should match pkg]

User Manual
F5D8230-4

Table of Contents

1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .x

Revolutionary 108Mbps Wireless Pre-N Technology with MIMO .x

Placement of your Wireless Pre-N Router . . . . . . . . . . . . . . . . .x

2 Product Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .x

Product Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .x

3 Knowing your Router . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .x

Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .x

System Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . .x

Easy Install Wizard Software System Requirements . . . . . .x

4 Connecting and Configuring your Router . . . . . . . . . . . . . . .x

5 Alternate Setup Method . . . . . . . . . . . . . . . . . . . . . . . . . . .x

6 Using the Web-Based Advanced User Interface . . . . . . . . . .x

Changing LAN Settings . . . . . . . . . . . . . . . . . . . . . . . . . . .x

Viewing the DHCP Client List Page . . . . . . . . . . . . . . . . . x

Configuring the Wireless Network Settings . . . . . . . . . . . x

Setting WPA Security. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .x

Setting WEP Encryption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .x

Using the Access Point Mode . . . . . . . . . . . . . . . . . . . . . .x

Setting MAC Address Control . . . . . . . . . . . . . . . . . . . . . .x

Configuring the Firewall . . . . . . . . . . . . . . . . . . . . . . . . . . x

Using Dynamic DNS

Utilities. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . x

Restarting the Router . . . . . . . . . . . . . . . . . . . . . . . . . x

Updating the Firmware . . . . . . . . . . . . . . . . . . . . . . . . x

7 Manually Configuring Network Settings . . . . . . .x

8 Recommended Web Browser Settings . . . . . . . . . . . . . . . . .x

9 How to Set Up your Network to Operate with AOL® for Broadband and

your New Belkin Router . . . . . . . . . . . . . . . .x

10 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .x

11 Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .x

F5D8230-4 user draft.doc Page 2 of 89

Introduction

Thank you for purchasing the Belkin Wireless Pre-N Router (the Router). Following are two short
sections—the first discusses the benefits of home networking, and the other outlines best
practices that maximize your wireless home network range and performance. Please be sure to
read through this User Manual completely, and pay special attention to the section entitled
“Placement of your Wireless Networking Hardware for Optimal Performance” on the next page.
By following our simple setup instructions you will be able to use your Belkin Home Network to:

• Share one high-speed Internet connection with all the computers in your home

• Share resources, such as files and hard drives among all the connected computers in

your home

• Share a single printer with the entire family

• Share documents, music, video, and digital pictures

• Store, retrieve, and copy files from one computer to another

• Simultaneously play games online, check Internet e-mail, and chat

Here are some of the advantages of setting up a Belkin Wireless Network:

• Mobility – you’ll no longer need a dedicated “computer room”—now you can work on a
networked laptop or desktop computer anywhere within your wireless range

• Easy installation – Belkin’s Easy Installation Wizard makes setup simple

• Flexibility – set up and access printers, computers, and other networking devices from

anywhere in your home

• Easy Expansion – the wide range of Belkin networking products let you expand your
network to include devices such as printers and gaming consoles

• No cabling required – you can spare the expense and hassle of retrofitting Ethernet

cabling throughout the home or office

• Widespread industry acceptance – choose from a wide range of interoperable networking

products.

MIMO technology will be used for 802.11n, a standard for next-generation 802.11 products that
boosts throughput to 100Mbps.

The element that makes Belkin’s Pre-N MIMO technology different from a conventional radio is
the use of three antennas and two simultaneous data streams to deliver wireless transfers around
your home or office. A conventional radio uses one antenna to transmit a data stream. Belkin’s
smart antenna radio (MIMO), on the other hand, uses three antennas. This design helps combat
distortion and interference. Belkin’s Pre-N MIMO is multidimensional. It builds on one-dimensional
smart antenna technology by simultaneously transmitting two data streams through the same
channel, which increases wireless capacity.

Think of conventional radio transmission as a two-lane highway. The speed limit governs the
maximum allowable flow of traffic through that lane. Compared with conventional radios, one­dimensional smart antenna systems help move traffic through that lane faster and more
reliably—analogous to a four-lane road on which traffic consistently moves at a rate closer to the
speed limit. Belkin’s Pre-N MIMO helps traffic move at the speed limit and opens more lanes—to
become the superhighway in this example. The rate of traffic flow is multiplied by the number of
lanes that are opened.

Revolutionary 108Mbps Wireless Pre-N Technology with MIMO

Your Belkin Wireless Pre-N Router uses a new smart antenna technology called Multiple Input
Multiple Output (MIMO). MIMO is a smart antenna technique that increases speed, range,
reliability, and spectral efficiency for wireless networking systems.

F5D8230-4 user draft.doc Page 3 of 89

During the 1990s, Stanford University researchers Greg Raleigh and V.K. Jones showed that a
characteristic of radio transmission called multipath, which had previously been considered an
impairment to radio transmission, is actually a gift of nature. Multipath occurs when signals sent
from a transmitter reflect off objects in the environment and take multiple paths to the receiver.
The researchers showed that multipath can be exploited to multiplicatively increase the capacity
of a radio system.

If each multipath route could be treated as a separate channel, it would be as if each route were a
separate virtual wire. A channel with multipath then would be like a bundle of virtual wires.

To exploit the benefits the virtual wires offer, MIMO uses multiple, spatially separated antennas.
MIMO encodes a high-speed data stream across multiple antennas. Each antenna carries a
separate, lower-speed stream. Multipath virtual wires are utilized to send the lower-speed
streams simultaneously.

But wireless is not as well-behaved as a bundle of wires. Each signal transmitted in a multipath
environment travels multiple routes. This makes a wireless system act like a bundle of wires with
a great deal of leakage between them, causing transmitted signals to jumble together. The MIMO
receiver uses mathematical algorithms to unravel and recover the transmitted signals.

Placement of your Wireless Pre-N Router

Important Factors for Placement and Setup

Your wireless connection will be stronger the closer your computer is to your Router (or access
point). Typical indoor operating range for wireless devices is between 100 and 200 feet.
In the same way, your wireless connection and performance will degrade somewhat as the
distance between your Router (or access point) and connected devices increases. This may or
may not be noticeable to you. As you move further from your Router (or access point), connection
speed may decrease. Factors that can weaken signals simply by getting in the way of your
network’s radio waves are metal appliances or obstructions, and walls.

If you have concerns about your network’s performance that might be related to range or
obstruction factors, try moving the computer to a position between five and 10 feet from the
Router (or access point) in order to see if distance is the problem. If difficulties persist even at
close range, please contact Belkin Technical Support.

Note: While some of the items listed below can affect network performance, they will not prohibit
your wireless network from functioning; if you are concerned that your network is not operating at
its maximum effectiveness, this checklist may help.

F5D8230-4 user draft.doc Page 4 of 89

1. Wireless Router or Access Point Placement

Place your Router (or access point), the central connection point of your network, as close as
possible to the center of your wireless network devices.
To achieve the best wireless network coverage for your “wireless clients” (i.e., computers enabled
by Belkin Wireless Notebook Network Cards, Wireless Desktop Network Cards, and Wireless
USB Adapters):

• Ensure that your Router’s (or access point’s) networking antennas are parallel to each
other, and are positioned vertically (toward the ceiling). If your Router (or access point)
itself is positioned vertically, point the antennas as much as possible in an upward
direction.

• In multistory homes, place the Router (or access point) on a floor that is as close to the
center of the home as possible. This may mean placing the Router (or access point) on
an upper floor.

• Try not to place the Router (or access point) near a cordless 2.4GHz phone.

2. Avoid Obstacles and Interference

Avoid placing your Router (or access point) near devices that may emit radio “noise,” such as
microwave ovens. Dense objects that can inhibit wireless communication include:

• Refrigerators

• Washers and/or dryers

• Metal cabinets

• Large aquariums

• Metallic-based UV tinted windows

If your wireless signal seems weak in some spots, make sure that objects such as these are not
blocking the signal’s path (between your computers and Router or access point)

3. Cordless Phones

If the performance of your wireless network is impaired after attending to the above issues, and
you have a cordless phone:

• Try moving cordless phones away from Routers (or access points) and your wireless-
enabled computers.

• Unplug and remove the battery from any cordless phone that operates on the 2.4GHz
band (check manufacturer’s information). If this fixes the problem, your phone may be
interfering.

• If your phone supports channel selection, change the channel on the phone to the
farthest channel from your wireless network. For example, change the phone to channel
1 and move your Router (or access point) to channel 11. See your phone’s user manual
for detailed instructions.

• If necessary, consider switching to a 900MHz or 5GHz cordless phone.

F5D8230-4 user draft.doc Page 5 of 89

4. Choose the “Quietest” Channel for your Wireless Network

In locations where homes or offices are close together, such as apartment buildings or office
complexes, there may be wireless networks nearby that can conflict with yours.
Use the Site Survey capabilities found in the Wireless Utility of your wireless adapter to locate
any other wireless networks that are available (see your wireless adapter’s user manual), and
move your Router (or access point) and computers to a channel as far away from other networks
as possible.

• Experiment with more than one of the available channels, in order to find the clearest
connection and avoid interference from neighboring cordless phones or other wireless
devices.

• For Belkin wireless networking products, use the detailed Site Survey and wireless
channel information included with your wireless network card. See your network card’s
user guide for more information.

These guidelines should allow you to cover the maximum possible area with your Router (or
access point). Should you need to cover an even wider area, we suggest the Belkin Wireless
Range Extender/Access Point.

5. Secure Connections, VPNs, and AOL

Secure connections typically require a user name and password, and are used where security is
important. Secure connections include:

• Virtual Private Network (VPN) connections, often used to connect remotely to an office
network

• The “Bring Your Own Access” program from America Online (AOL), which lets you use
AOL through broadband provided by another cable or DSL service

• Most online banking websites

• Many commercial websites which require a username and password to access your

account

Secure connections can be interrupted by a computer’s power management setting, which
causes it to “go to sleep.” The simplest solution to avoid this is to simply reconnect by rerunning
the VPN or AOL software, or by re-logging into the secure website.
A second alternative is to change your computer’s power management settings so it does not go
to sleep; however, this may not be appropriate for portable computers. To change your power
management setting under Windows, see the “Power Options” item in the Control Panel.
If you continue to have difficulty with Secure Connections, VPNs, and AOL, please review the
steps above to be sure you have addressed these issues.

For more information regarding our networking products, visit our website at
www.belkin.com/networking or call Belkin Technical Support at:

US: 877-736-5771
310-898-1100 ext. 2263
Europe: 00 800 223 55 460
Australia: 1800 235 546

Product Overview

Product Features

In minutes you will be able to share your Internet connection and network your computers. The
following is a list of features that make your new Belkin Wireless Pre-N Router an ideal solution
for your home or small office network.

F5D8230-4 user draft.doc Page 6 of 89

Works with Both PCs and Mac® Computers

The Router supports a variety of networking environments including Mac OS® 8.x, 9.x, X v10.x,
AppleTalk®, Linux®, Windows® 95, 98, Me, NT®, 2000, and XP, and others. All that is needed is
an Internet browser and a network adapter that supports TCP/IP (the standard language of the
Internet).

LED Display

Lighted LEDs on the top of the Router indicate which functions are in operation.

Web-Based Advanced User Interface

You can set up the Router’s advanced functions easily through your web browser, without having
to install additional software onto the computer. There are no disks to install or keep track of and,
best of all, you can make changes and perform setup functions from any computer on the
network quickly and easily.

NAT IP Address Sharing

Your Router employs Network Address Translation (NAT) to share the single IP address
assigned to you by your Internet Service Provider while saving the cost of adding additional IP

addresses to your Internet service account.

SPI Firewall

Your Router is equipped with a firewall that will protect your network from a wide array of
common hacker attacks including IP Spoofing, Land Attack, Ping of Death (PoD), Denial of
Service (DoS), IP with zero length, Smurf Attack, TCP Null Scan, SYN flood, UDP flooding, Tear
Drop Attack, ICMP defect, RIP defect, and fragment flooding.

Integrated 10/100 4-Port Switch

The Router has a built-in, four-port network switch to allow your wired computers to share
printers, data and MP3 files, digital photos, and much more. The switch features automatic
detection so it will adjust to the speed of connected devices. The switch will transfer data between
computers and the Internet simultaneously without interrupting or consuming resources.

Universal Plug and Play (UPnP)

UPnP is a technology that offers seamless operation of voice messaging, video messaging,
games, and other applications that are UPnP-compliant.

Support for VPN Pass-Through

If you connect to your office network from home using a VPN connection, your Router will allow
your VPN-equipped computer to pass through the Router and to your office network.

Built-In Dynamic Host Configuration Protocol (DHCP)

Built-In Dynamic Host Configuration Protocol (DHCP) on-board makes for the easiest possible
connection of a network. The DHCP server will assign IP addresses to each computer
automatically so there is no need for a complicated networking setup.

Easy Install Wizard

The Easy Install Wizard takes the guesswork out of setting up your Router. This automatic
software determines your network settings for you and sets up the Router for connection to your
Internet Service Provider (ISP). In a matter of minutes, your Router will be up and running on the
Internet.

Note: Easy Install Wizard software is compatible with Windows 98SE, Me, 2000, XP, and Mac
OS 9.X and Mac OS X. If you are using another operating system, the Router can be set up using
the Alternative Method described in this User Manual (see page xx) [VERIFY PAGE NUMBER].

F5D8230-4 user draft.doc Page 7 of 89

Integrated Pre-N Wireless Access Point

Pre-N is an exciting new wireless technology that achieves data rates up to 108Mbps.

Integrated Parental Control Web Content Filter

Belkin has teamed with Cerberian, a leading content-filtering company, to bring you this unique
feature. Your Belkin Wireless Pre-N Router is the first home networking solution with an
integrated web content filter that allows you to block unwanted or offensive web content before it
makes it to your network.

Unlike similar access-control products, Belkin Parental Control is built into our Router, so there is
no software to install on any computer and you will never be charged a per-computer fee for the
service. Your Router comes with a free six-month subscription, with no credit card required for
this trial period. This lets you take advantage of Parental Control’s capabilities right away.

Belkin Parental Control allows you to set up your own policies and block any website you want.
There is also an optional reporting feature (fee-based) that allows you to get a report showing you
every website that was visited from your network (refer to your Parental Control User Manual for
more information).

MAC Address Filtering

For added security, you can set up a list of MAC addresses (unique client identifiers) that are
allowed access to your network. Every computer has its own MAC address. Simply enter these
MAC addresses into a list using the Web-Based Advanced User Interface and you can control
access to your network.

Knowing your Router

Package Contents

• Belkin Wireless Pre-N Router

• Quick Installation Guide

• Belkin Easy Install Wizard Software CD

• Belkin RJ45 Ethernet Networking Cable

• Power Supply

• User Manual

System Requirements

• Broadband Internet connection such as a cable or DSL modem with RJ45 (Ethernet)
connection

• At least one computer with an installed network interface adapter

• TCP/IP networking protocol installed on each computer

• RJ45 Ethernet networking cable

• Internet browser

Easy Install Wizard Software System Requirements

• A PC running Windows® 98SE, Me, 2000, or XP, or a Mac® computer running Mac OS

®

9.x or OS X

• Minimum 64MB RAM

• Internet browser

F5D8230-4 user draft.doc Page 8 of 89

Knowing your Router

The Router has been designed to be placed on a desktop. All of the cables exit from the rear of
the Router for better organization and utility. The LED indicators are easily visible on the TOP of
the Router to provide you with information about network activity and status.

Line art below is a little messed up on the port lights(JH)

Top Panel

Power LED

Indicates that power is applied to the Router

OFF

Router is OFF
ON

Router is powered ON

Wireless: Wireless Network LED

OFF

Wireless network is OFF
Green

Wireless network is ready
Blinking

Indicates wireless activity

Internet LED

This LED lights in GREEN to indicate that your modem is
connected properly to the Router. It blinks rapidly when information
is being sent over the port between the Router and the modem.

OFF

No connection to the modem
Solid Green

Good connection to the modem
Blinking Green

Data is being sent from the Router to the modem

LAN Port-Status LEDs

These LEDs are labeled 1– 4 and correspond to the numbered ports
on the rear of the Router. When a computer is properly connected to
one of the LAN ports on the rear of the Router, the LED will light.
GREEN means a 10Base-T device is connected, AMBER means a
100Base-T device is connected. When information is being sent
over the port, the LED blinks rapidly.

OFF

No device is linked to the port
Green
Blinking

10Base-T or 100Base-Tx device connected
Network activity

F5D8230-4 user draft.doc Page 9 of 89

Rear Panel

Power Jack – GRAY

Connect the included 12V DC power supply to this jack

Connections to Computers (LAN Ports) – BLUE

Connect your wired (non-wireless) computers to these ports. These ports are RJ45, 10/100 auto­negotiation, auto-uplinking ports for standard UTP category 5 or 6 Ethernet cable. The ports are
labeled 1 through 4. These ports correspond to the numbered LEDs on the top of the Router.

Connection to Modem (Internet/WAN Port) – GREEN

This port is for connection to your cable or DSL modem. Use the cable that was provided with the
modem to connect the modem to this port. Use of a cable other than the cable supplied with the
cable modem may not work properly.

Reset Button (Located on bottom of Router)

The “Reset” button is used in rare cases when the Router may function improperly. Resetting the
Router will restore the Router’s normal operation while maintaining the programmed settings. You
can also restore the factory default settings by using the “Reset” button. Use the restore option in
instances where you may have forgotten your custom password.

Resetting the Router

Push and release the “Reset” button. The lights on the Router will momentarily flash. When the
lights stop blinking, the reset is complete.

Restoring the Factory Defaults

Press and hold the “Reset” button for at least 10 seconds then release it. The lights on the Router
will momentarily flash. When the lights stop blinking, the reset is complete.

Connecting and Configuring your Router

F5D8230-4 user draft.doc Page 10 of 89

Verify the contents of your box. You should have the following:

• Belkin Wireless Pre-N Router

• Category 5 Networking Cable (for connecting the Router to the computer)

• Power Supply

• Belkin Easy Install Wizard Software CD

• User Manual

Modem Requirements

Your cable or DSL modem must be equipped with an RJ45 Ethernet port. Many modems have
both an RJ45 Ethernet port and a USB connection. If you have a modem with both Ethernet and
USB, and are using the USB connection at this time, you will be instructed to use the RJ45
Ethernet port during the installation procedure. If your modem has only a USB port, you can
request a different type of modem from your ISP, or you can, in some cases, purchase a modem
that has an RJ45 Ethernet port on it.

[USB and Ethernet connector.tif]

Easy Install Wizard

Belkin has provided our Easy Install Wizard software to make installing your Router a simple and
easy task. You can use it to get your Router up and running in minutes. The Easy Install Wizard
requires that your Windows 98SE, Me, 2000, or XP computer be connected directly to your cable
or DSL modem and that the Internet connection is active and working at the time of installation.
If it is not, you must use the “Alternative Setup Method” section of this User Manual to configure
your Router. Additionally, if you are using an operating system other than Windows 98SE, Me,
2000, or XP, you must set up the Router using the “Alternative Setup Method” section of this User
Manual.

Run the Easy Install Wizard Software

1. Shut down any programs that are running on your computer at this time.

2. Make sure you have the following items at the computer that is now directly connected to the
cable or DSL modem. DO NOT CONNECT THE ROUTER AT THIS TIME.

• The Easy Install Wizard CD-ROM

• The Router

• The Router Power Supply

• Category 5 Networking Cable

• This User Manual

3. Turn off any firewall or Internet-connection-sharing software on your computer.

4. Insert the Easy Install Wizard software CD into your CD–ROM drive. The Easy Install Wizard

screen will automatically appear on your screen within 15 seconds. If it does not, select your
CD-ROM drive from “My Computer” and double-click on the file named “Setup” on the CD­ROM.

5. Follow the Easy Install Wizard to complete the installation

Ethernet

USB

IMPORTANT: Run the Easy Install Wizard from the computer that is directly connected to the cable or

DSL modem. DO NOT CONNECT THE ROUTER AT THIS TIME.

F5D8230-4 user draft.doc Page 11 of 89

Welcome Screen

After you insert the CD into your CD-ROM drive, the Wizard’s welcome screen will appear. Make
sure you have not connected the Router at this point. If you have connected your Router, please
reconnect your computer directly to the modem. Click “Next” when you are ready to move on.

[01.tif] (that’s the wrong screenshot, we know that, right? It says “4 Port Router”)

Progress Screen

Easy Install will show you a progress screen each time a step in the setup has been completed.
Each time you see the progress screen, click “Next” when you are ready to move to the next step.

[02.tif]

F5D8230-4 user draft.doc Page 12 of 89

1.1 Examining Settings

The Wizard will now examine your computer’s network settings and gather information
needed to complete the Router’s connection to the Internet. When the Wizard is finished
examining your computer, click “Next” to continue.

[03.tif]

1.2 Multi-NICs Screen

This screen will appear ONLY if you have more than one network adapter installed in your
computer. If you have more than one network adapter installed in your computer, the Wizard
will need to know which adapter is connected to your modem. Select the network card that is
connected to your modem from the list and click “Next”. If you are not sure which adapter to
choose, select the adapter at the top of the list. If you mistakenly choose the wrong adapter
now, you will be able to choose a different one later.

[multiple adapters screen.tif]

Step 2: Hardware Setup - Connect the Router to your Modem and Computer

The Wizard will walk you through connecting your Router to your computer and modem.
Follow the steps on the screen using the pictures as a guide.

F5D8230-4 user draft.doc Page 13 of 89

2.1 This step instructs you to locate the cable connected between your modem and the

networking port on your computer. Unplug this cable from the computer and plug it into
the GREEN port on the Router. Click “Next” to continue.

[04.tif]

2.2 This step instructs you to locate the BLUE cable that is included with your Router. Plug

one end of this cable into ANY one of the BLUE ports on your Router. Plug the other end
of the cable into the networking port on your computer. Click “Next” to continue.

[05.tif]

F5D8230-4 user draft.doc Page 14 of 89

2.3 This step instructs you to locate the power supply that is included with your Router. Plug

the power supply’s small connector into the GRAY port on the Router. Plug the power
supply into an empty power outlet. Click “Next” to continue.

[06.tif]

2.4 This step instructs you to look at the lights on the front of your Router. Make sure the

appropriate lights are ON. Refer to the Easy Install Wizard software on your computer’s
screen for more details. Click “Next” to continue.

[07.tif]

F5D8230-4 user draft.doc Page 15 of 89

Step 3: Checking the Connection

3.1 Once you have completed connecting the Router, the Wizard will check the connection to

the Router then go on to determine what type of Internet connection you have.

[09.tif]

3.2 User Name and Password Needed

If you have a connection type that requires a user name and a password, the Wizard will ask
you to type in your user name and password. If your connection type does not require a user
name and password, you will not see this screen.

Your user name and password is provided to you by your Internet Service Provider. If you
have to type in a user name and password to connect to the Internet, then type that same
user name and password in here. Your user name looks something like “[e-mail]”
or simply “jsmith”. The service name is optional and is very rarely required by your ISP. If
you don’t know your service name, leave this blank. When you have entered your
information, click “Next” to move on.

[10.tif]

F5D8230-4 user draft.doc Page 16 of 89

3.3 Wireless Setup

This Step Is Optional. Click “Next” if you want to skip it.
Using this step, you can customize your wireless network settings if you want to. Follow the
steps on the screen to complete this step. Click “Next” to continue.

[11.tif]

Step 4: Configuring the Router

The Wizard will now transfer all of the configuration information to the Router. This will take
approximately one minute. During this time, do not turn off the Router or computer. The
Router will restart itself at the end of this step.

[13.tif]

F5D8230-4 user draft.doc Page 17 of 89

4.1 Checking Internet

The Wizard will now check for an Internet connection. This can take a few minutes. The
Wizard may not detect a connection right away. If not, it will retry a number of times. The
“Connected” light on the front panel of the Router will flash during this time. Please be

patient through this process.

[16.tif] Need correct picture

4.2 Finished

When the Internet connection is complete, the Wizard will tell you that you are finished.
The “Connected” LED on the front of the Router will be solid GREEN, indicating that the
Router is now connected to the Internet.

[finished.tif]

Your Router is now connected to the Internet. Now you can begin surfing the Internet by

opening your browser and going to your favorite web page.

Congratulations! You have finished installing your new Belkin Router. You are ready to set up
the other computers in your home. You can also add computers to your Router any time you
want.

Alternative Method
Step 1: Connecting your Gateway Router

F5D8230-4 user draft.doc Page 18 of 89

1.1 Turn off the power to your modem by unplugging the power supply from the modem.

1.2 Locate the network cable that is connected between your modem and your computer and

unplug it from your computer, leaving the other end connected to your modem.

1.3 Plug the loose end of the cable you just unplugged into the port on the back of the Router

labeled “Internet/WAN”.

1.4 Connect the included network cable from the back of the computer to one of the ports

labeled “1–4”. Note: It does not matter which numbered port you choose.

1.5 Turn your cable or DSL modem on by reconnecting the power supply to the modem.

1.6 Before plugging the power cord into the Router, plug the cord into the wall, then plug the

cord into the Router’s power jack.

[Need correct illustration]

1.7 Verify that your modem is connected to the Router by checking the lights on the TOP of

the Router. The green light labeled “WAN” should be ON if your modem is connected
correctly to the Router. If it is not, recheck your connections.

1.8 Verify that your computer is connected properly to the Router by checking the lights

labeled “LAN 1,2,3,4”. The light which corresponds to the numbered port connected to
your computer should be ON, if your computer is connected properly. If it is not, recheck
your connections.

Alternative Method
Step 2: Set your Computer’s Network Settings to Work with a DHCP Server

See the section in this User Manual called “Manually Configuring Network Settings” for directions.

To power adapter

Cable or DSL
modem

Existing network
cable (that came
with modem)

Supplied Blue Ethernet
cable (to computer)

Mac or PC computer
that was originally
connected to the cable
or DSL modem

F5D8230-4 user draft.doc Page 19 of 89

Alternative Method
Step 3: Configuring the Router Using the Web-Based Advanced User Interface

Using your Internet browser, you can access the Router’s Web-Based Advanced User Interface.
In your browser, type “192.168.2.1” (do not type in anything else such as “http://” or “www”). Then
press the “Enter” key.

[http_bar.tif]

Logging into the Router

You will see the Router’s home page in your browser window. The home page is visible to any
user who wants to see it. To make any changes to the Router’s settings, you have to log in.
Clicking the “Login” button or clicking on any one of the links on the home page will take you to
the login screen. The Router ships with no password entered. In the login screen, leave the
password blank and click the “Submit” button to log in.

[login screen.tif]

F5D8230-4 user draft.doc Page 20 of 89

Logging out of the Router

One computer at a time can log into the Router for the purposes of making changes to the
settings of the Router. Once a user has logged in to make changes, there are two ways that the
computer can be logged out. Clicking the “Logout” button will log the computer out. The second
method is automatic. The login will time out after a specified period of time. The default login
timeout is 10 minutes. This can be changed from one to 99 minutes. For more information, see
the section in this manual titled “Changing the Login Timeout Setting”.

Understanding the Web-Based Advanced User Interface

The home page is the first page you will see when you access the Advanced User Interface (UI).
The home page shows you a quick view of the Router’s status and settings. All advanced setup
pages can be reached from this page.

[status.tif] [PM: pls verify screenshot, it’s showing wrong part number]

1. Quick-Navigation Links

You can go directly to any of the Router’s advanced UI pages by clicking directly on these links.
The links are divided into logical categories and grouped by tabs to make finding a particular
setting easier to find. Clicking on the purple header of each tab will show you a short description
of the tab’s function.

(1)

(2)

(5)

(3)

(4)

(9)

(6)

(8)

(7)

(10)

F5D8230-4 user draft.doc Page 21 of 89

2. Home Button

The home button is available in every page of the UI. Pressing this button will take you back to
the home page.

3. Internet Status Indicator

This indicator is visible in all pages of the Router, indicating the connection status of the Router.
When the indicator says “connection OK” in GREEN, the Router is connected to the Internet.
When the Router is not connected to the Internet, the indicator will read “no connection” in RED.
The indicator is automatically updated when you make changes to the settings of the Router.

4. Login/Logout Button

This button enables you to log in and out of the Router with the press of one button. When you
are logged into the Router, this button will change to read “Logout”. Logging into the Router will
take you to a separate login page where you will need to enter a password. When you are logged
into the Router, you can make changes to the settings. When you are finished making changes,
you can log out of the Router by clicking the “Logout” button. For more information about logging
into the Router, see the section called “Logging into the Router”.

5. Help Button

The “Help” button gives you access to the Router’s help pages. Help is also available on many
pages by clicking “more info” next to certain sections of each page.

6. LAN Settings

Shows you the settings of the Local Area Network (LAN) side of the Router. Changes can be
made to the settings by clicking on any one of the links (IP Address, Subnet Mask, DHCP Server)
or by clicking the “LAN” quick-navigation link on the left side of the screen.

7. Features

Shows the status of the Router’s NAT, firewall, and wireless features. Changes can be made to
the settings by clicking on any one of the links or by clicking the quick-navigation links on the left
side of the screen.

8. Internet Settings

Shows the settings of the Internet/WAN side of the Router that connects to the Internet. Changes
to any of these settings can be made by clicking on the links or by clicking on the “Internet/WAN”
quick-navigation link on the left side of the screen.

9. Version Info

Shows the firmware version, boot-code version, hardware version, and serial number of the
Router.

10. Page Name

The page you are on can be identified by this name. This User Manual will sometimes refer to
pages by name. For instance “LAN > LAN Settings” refers to the “LAN Settings” page.

F5D8230-4 user draft.doc Page 22 of 89

Step 4: Configuring your Router for Connection to your Internet Service Provider (ISP)

The “Internet/WAN” tab is where you will set up your Router to connect to your Internet Service
Provider (ISP). The Router is capable of connecting to virtually any ISP’s system provided you
have correctly configured the Router’s settings for your ISP’s connection type. Your ISP
connection settings are provided to you by your ISP. To configure the Router with the settings
that your ISP gave you, click “Connection Type” (A) on the left side of the screen. Select the
connection type you use. If your ISP gave you DNS settings, clicking “DNS” (B) allows you to
enter DNS address entries for ISPs that require specific settings. Clicking “MAC Address” (C) will
let you clone your computer’s MAC address or type in a specific WAN MAC address, if required
by your ISP. When you have finished making settings, the “Internet Status” indicator will read
“connection OK” if your Router is set up properly.

[wan.tif]

(A)

(B)

(C)

F5D8230-4 user draft.doc Page 23 of 89

Setting your Connection Type

From the “Connection Type” page, you can select the type of connection you use. Select the type
of connection you use by clicking the button (1) next to your connection type and then clicking
“Next” (2).

[WAN connection type.tif]

(1)

(2)

F5D8230-4 user draft.doc Page 24 of 89

Setting your Internet Service Provider (ISP) Connection Type to Dynamic IP

A dynamic connection type is the most common connection type found with cable modems.
Setting the connection type to “dynamic” in many cases is enough to complete the connection to
your ISP. Some dynamic connection types may require a host name. You can enter your host
name in the space provided if you were assigned one. Your host name is assigned by your ISP.
Some dynamic connections may require that you clone the MAC address of the PC that was
originally connected to the modem.

1. Host Name

This space is provided to enter a host name that needs to be visible to your ISP. Enter your host
name here and click “Apply Changes” (3). If your ISP did not assign you a host name, or you are
not sure, leave this blank.

2. Change WAN MAC Address

If your ISP requires a specific MAC address to connect to the service, you can enter a specific
MAC address or clone the current computer’s MAC address through this link.

Setting your Internet Service Provider (ISP) Connection Type to Static IP

A static IP address connection type is less common than other connection types. If your ISP uses
static IP addressing, you will need your IP address, subnet mask, and ISP gateway address. This
information is available from your ISP or on the paperwork that your ISP left with you. Type in
your information, then click “Apply Changes” (3). After you apply the changes, the Internet Status
indicator will read “connection OK” if your Router is set up properly.

(1)

(3)

(2)

F5D8230-4 user draft.doc Page 25 of 89

1. IP Address

Provided by your ISP. Enter your IP address here.

2. Subnet Mask

Provided by your ISP. Enter your subnet mask here.

3. ISP Gateway Address

Provided by your ISP. Enter the ISP gateway address here.

4. My ISP Provides More Than One Static IP Address

If your ISP assigns you more than one static IP address, your Router is capable of handling up to
five static WAN IP addresses. Select “My ISP provides more than one static IP address” and
enter your additional addresses.

[static.tif]

(1)

(2)

(3)

(4)

(5)

F5D8230-4 user draft.doc Page 26 of 89

Setting your ISP Connection Type to PPPoE

Most DSL providers use PPPoE as the connection type. If you use a DSL modem to connect to
the Internet, your ISP may use PPPoE to log you into the service. If you have an Internet
connection in your home or small office that doesn’t require a modem, you may also use PPPoE.
Your connection type is PPPoE if:

1) Your ISP gave you a user name and password, which is required to connect to the Internet.

2) Your ISP gave you software such as WinPOET or Enternet300 that you use to connect to the

Internet.

3) You have to double-click on a desktop icon other than your browser to get on the Internet.

[pppoe.tif]

1. User Name

This space is provided to type in your user name that was assigned by your ISP.

2. Password

Type in your password and retype it into the “Retype Password” box to confirm it.

3. Service Name

A service name is rarely required by an ISP. If you are not sure if your ISP requires a service
name, leave this blank.

4. MTU

The MTU setting should never be changed unless your ISP gives you a specific MTU setting.
Making changes to the MTU setting can cause problems with your Internet connection including
disconnection from the Internet, slow Internet access, and problems with Internet applications
working properly.

5. Disconnect after X...

The “Disconnect” feature is used to automatically disconnect the Router from your ISP when
there is no activity for a specified period of time. For instance, placing a check mark next to this
option and entering “5” into the minute field will cause the Router to disconnect from the Internet
after five minutes of no Internet activity. This option should be used if you pay for your Internet
service by the minute.

(1)

(2)

(3)

(4)

(5)

F5D8230-4 user draft.doc Page 27 of 89

Setting your Internet Service Provider (ISP) Connection Type to Point-to-Point Tunneling
Protocol (PPTP) [European Countries Only].

Some ISPs require a connection using PPTP protocol, a type of connection most common in
European countries. This sets up a direct connection to the ISP’s system. Type in the information
provided by your ISP in the space provided. When you have finished, click “Apply Changes” (9).
After you apply the changes, the Internet Status indicator will read “connection OK” if your Router
is set up properly.

[PPTP.tif]

1. PPTP Account

Provided by your ISP. Enter your PPTP account name here.

2. PPTP Password

Type in your password and retype it into the “Retype Password” box to confirm it.

3. Host Name

Provided by your ISP. Enter your host name here.

(1)

(2)

(3)

(4)
(5)

(6)

(7)

(8)

(9)