Airflo AFF001 User Manual

INSTRUCTION MANUAL

Bar Cooler

(Available in single, 2-Door and 3-Door)

IMPORTANT SAFETY INSTRUCTIONS

Before switching on your Bar Cooler for the first time, read the information in
this Users’ Manual carefully. Keep this booklet in a safe place for future
reference. If you ever sell you appliance, hand this manual to the new owner.

The manufacturer does not accept responsibility for any damages that may
arise from failure to follow the instructions in this manual.

· Do not use damaged appliances. If you are in any doubt, consult an

authorized service center agent.

· Connection and installation of your Bar Cooler are to be car ried out in strict

compliance with the manual’s guidelines.

· For safety purposes, the appliance must be properly earthed in accordance

with specifications.

· Do not damage any part s o f t he appliance which carr y refrigerant b y pi er c ing,

perforating, crushing, twisting or scraping. If the refrigerant comes into contact
with the eyes, it may cause serious eye injury.

· Always remember to unplug the appliance before cleaning. Never unplug

your appliance by pulling on the power cable. Always grip the plug firmly and
pull straight out from the socket. Always check that the plug and cable are
undamaged.

All repairs must b e ca rri ed out by q ualifie d s erv ice ag ent s. I nadeq uate r ep ai rs

·

may be dangerous. Never try to repair the Bar Cooler yourself.

· Should the cover of the interior light of the fan fall off or break, switch the Bar

Cooler off immediately and replace the cover.

· Ensure your chosen location has a flat and stable surface. The unit may be

leveled by turning either or both of the adjustable feet in the front corners.

Check the unit is level using a spirit level.

·

· Do not obstruct or cover the ventilation aperture.

· Do not position this appliance with its rear panel directly against a wall.

Maintain a gap of at least 50 mm between the appliance and any adjacent w all .

· Position the Bar Cooler away from heat sources. The Bar Cool er shoul d be

placed in a well-v entil ated and prot ecte d from moisture or ex treme h eat or col d.
Note that the refrigerator may not function properly if the temperature rises

above 30°C. The refrigerator meets the operating conditions according to the
standard EN 441-4 in climate class 4. A 10A fuse is fitted. Never replace with a
fuse rated higher than this.

· Do not allow children to play with the appliance or to sit on it or to hang onto

the door.

· Make sure there is a suitable power outlet (230 volts, 13 amps outlet) with

proper grounding to power the refrigerator.

· Do not store explosive substances such as aerosol cans with a flammable

propellant in this appliance.

· Ensure all vents are clear of obstruction particularly if the unit is built-in.

· Do not use mechanical devices or other means to accelerate the defrosting

process, other than those recommended by the manufacturer.

· Do not damage the refrigerant circuit.

· Do not use electrical appliances inside the food storage compartments of the

appliance, unless they ar e the type recommended by the manufacturer.

BEFORE USING FOR THE FIRST TIME, do not position this appli ance w i th it s
rear panel directly against a wall. For good circulation and operating efficiency,
the ventilation grills must never be blocked.

Remove all packaging and place the Bar Cooler on a stable, secure and flat
surface.

Never use an extension lead. If the mains cable does not reach the nearest
socket, either rearrange your layout or ask a qualified electrician to fit a new
socket.

If the power is cut off, wait for at least 5 minutes before plugging the unit in
again to avoid damaging the compressor.

Do not place combustible, explosive or volatile articles / items, corrosive acid
or alkali or liquid in glass containers into the chiller. Always exercise caution
when adjusting the temperature.

IMPORTANT: Allow the refrigerator to stand upright for 24 hours be fore
plugging it in.

OPERATION

· Place the shelves firmly on their supports. Check that the refrigerator is

functioning properly before installing and filling it. An optional light switch is
inside the unit.

· Never put warm or hot food directly into the Bar Cooler.

There are several types of controller/thermostat for different models.
Please check which type of controller is on your unit.

ELECTRONIC THERMOSTAT

· During normal operation, the

controller display will
show the temperature inside the

refrigerator.

· A small indicator light

will illuminate under the “Cooling” symbol to confirm the fridge is in its normal
cooling mode and compressor is running.

· When temperature is reached and the compressor is in its “Off” cycle, no

indicator light will illumin ate in the controller:

OPERATIO N O F THE CONTROLLER

To set the desired temperature of the fridge:

· Press the button once. A “beep” will sound and the display will start to

flash.

· Use the buttons to set to the desired temperature.

· Press again to complete the operation, or just leave it for 5-10 seconds

and the display will revert back to showing internal temperature while new
settings is saved.

Note: The fridge is built to automatically defrost and prevent any ice forming
on the evaporator. When in a “Defrost” cycle, the indicator light will illumina te

under the “Defrost” symbol:

To manuall y act iv at e “Defrost” cycle:

· Press the button an d hold it for 6 sec o nds until a “beep” can be heard.

· The indicator l ight will now il lumi nate un der the “Defrost” symbol

and the fridge is into a “Defrost” cycle.

· “Defrost” will run for 20 minutes and then automatically revert to normal

operation.

To manually change back to normal operating mode from the “Defrost”
mode:

· Press the button again. Hold the button for 6 seconds until a “beep” is

heard.

· Both indicator lights under the “Defrost” symbol and under the “Cooling”

symbol will now flash whil e the fri dg e i s g earing up to switc h back
to normal operation.

· After 5-20 minutes, only the indicator light will illuminate under

the “Cooling” symbol to confirm the fridge is back in its normal cooling mode.

MECHANICAL THERMOSTAT

Thermostat settings

Thermostat “Off” position indicates the Bar Cooler is switched off although

·

power is still supplied. By turning the thermostat dial clockwise, the Bar Cooler
will switch on automatically. The settings MIN-MAX will regulate the interior
temperature of the Bar Cooler.

Setting Off = Not operating
Setting MIN = Lowest setting
(w armest internal temperature)
Setting MAX = Highest setting
(coldest internal temperature)

· Adjust the internal temperature as required according to

the amount of product and the ambient temperature.

· The internal temperature varies in different parts of the Bar Cooler. The back

of the Bar Cooler is coldest.

IMPORTANT

· The fridge will go through a normal periodical defrosting cycle and a manual

defrosting oper ation is only req uir ed in mos t e xt reme cas es. It is be tter to avoid
if not necessary.

· While in the “Defrost” mode, the fridge cooling power is reduced as the

compressor is not working. The a ut o mati c c ycles ensure t he defrosting is done
in the most efficient manner and when required. It is not recommended to
leave the fridge i n t h e man ual l y s et D e frost mode for prolonged periods of time
though.

· Note that it is not recommended to operate the fridge on settings that run

below 4°C/ MAX as such setting will cause content at the rear of the fridge
(closest to the evaporator) to freeze. It will also result to unnecessary strain on
the cooling system and undue high energy consumption.

· In normal operation, the controller turns the compressor off at the set

temperature and back on after the temperature rise by around 5°C. As such,
the reading in the electronic controller is almost always a few degrees above
set-point, which is perfectly okay.

DEFROSTING / MAINTENANCE

· Ice may build up on the evaporator if the unit is put to work constantly for a

period of time. When ice begins to build up to approximately 10mm or 1/5 inch
thick, defrost is required.

· Empty the cabinet, switch the thermostat to “Off” position. The ice will start to

melt.

· When the i ce has mel ted an d drai ned aw ay, dry off any r esidu al moi sture w i th

a soft cloth.

· Switch the power on again via the thermostat.

· Note that it may take around 12 hours for the cabinet to get back down to the

previous temperature set.

CLEANING

· Unplug y our Bar C ooler and r emov e any ite ms insi de (pre fer ably to a suitable

back-up refrigerator).

· Wash the inner compartment with warm water and neutral detergent.

· Do not allow the control panel, cables or plug to get wet.

· Never use corrosive detergents, wire brushes or abrasive scourers to clean

your Bar Cooler. Also, never use metal or sharp implements to remove debris /
dirt.

· Dry all surface thoroughly.

· To ensure a trouble-free operation, the condenser should be cleaned every

three months, where appropriate, using a vacuum hose. The condenser is
located behind the lower grill of the cabinet. In exceptionally dusty locations,
the condenser should be cleaned often.

· Use mild, soapy water to clean the gasket and seals.

REPLACING LAMPS

· Unplug the power plug.

· Remove the scr ews on b oth e nd of th e li ght cov er. Take down the lamp cover,

pull out the wires and then take out the lamp.

· Install the new lamp, connect the wires, place the lamp cover and fasten.

DISPOSAL OF PACKAGING

· Do not allow children to play with the packaging. Destroy plastic bags safely.

· The cardboard m ay be broken or cut i nto s mall er piec es and g iv en to a w aste

paper disposal service. The wrapping foil is made of polyethylene. The
polyethylene pads and stuffing contain no fluorochloric hydrocarbons.

· All these packaging materials may be taken to a waste collecting depot and

used again after adeq uate rec y c l ing.