Page 1
MODEL: 807
3/8” Mini Composite Palm Ratchet
Page 2
Important Warnings - Ratchets
1. Eye protection and hearing protection and safety gloves must always be worn when operating an impact wrench or impact
driver.
2. When using heavy impact sockets or sockets on impact wrenches with 3/4” drive anvils or larger, a socket retaining ring
and pin should be used to prevent the socket falling off and causing injury.
Accessory Hazards
3. Disconnect the assembly power tool for threaded fasteners from the energy supply before changing the inserted tool or
accessory.
4. Do not touch sockets or accessories during impacting as this increases the risk of cuts, burns or vibration injuries.
5. Use only sizes and types of accessories and consumables that are recommended by the assembly power tool for threaded
fasteners manufacturer; do not use other types or sizes of accessories and consumables.
SPECIFICATIONS
Model No.
Free Speed
(RPM)
Bolt Capacity
(in.)
Square
Drive
(in.)
Working
Torque
Max. Torque
(ft-lb) @90 psi
Weight
(lbs.)
Length
(in)
Air Cons.
(CFM)
Rec. Hose
Size
(in.)
Air Inlet
(in.)
807 300 3/8 1/4 5-25 ft-lb 35 1.1 5.4 3 3/8 1/4 NPT
Air Supply
Tools of this class operate on a wide range of air pressure. It is recommended that air pressure of these tools measures 90 PSI at the tool while running free. Higher
pressure and unclean air will shorten the tool’s life because of faster wear and may create a hazardous condition and void the warranty. Water in the air line will
cause damage to the tool. Drain the air tank daily. Clean the air inlet lter screen on at least a weekly schedule. The recommended hookup procedure can be viewed
in the illustration below. The air inlet, used for connecting air supply, has standard 1/4” NPT American Thread. Line pressure should be increased to compensate for
unusually long air hoses (over 25 feet). Minimum hose diameter should be 3/8” I.D. and ttings should have the same inside dimensions.
Page 3
MODEL: 807
3/8” Mini Composite Palm Ratchet
Exploded View & Parts List
41
40
39
38
26
25
35
36
37
33
31
30
24
34
28
29
32
22
23
27
12
13
14
15
16x4
17
18
19
20
21
11
10
42
08
07
09
06
05
04
03
02
01
Ref # Part Number Description Qty Ref # Part Number Description Qty.
1 9861401A PLUG 1 23 9861422 GEAR PIVOT 3
2 9OR1898 O-RING 1 24 98614S223 CRANK SHAFT 1
3 9861403A THROTTLE VALVE SPRING 1 25 98614S525 CLAMP NUT 1
4 9861404 VALVE 1 26 98614S226 RATCHET HOUSING 1
5 9861405A VALVE STEM 1 27 9NB-HK1312 NEEDLE BEARING 1
6 9861406A VALVE BUSHING 1 28 98614S229 DRIVE BUSHING 1
7 98614S207 AIR INLET BUSHING 1 29 98614S230 RATCHET YOKE 1
8 98614S508-BK THROTTLE LEVER 1 30 98614S530 SCREW 1
9 9308003 SPRING PIN 1 31 98614S532-4 REVERSE BUTTON 1
10 98614S510C-CAT COMPOSITE HOUSING 1 32 98614S231 WASHER 1
11 98614S510CA MOTOR HOUSING 1 33 98614S233 PAWL PIVOT 1
12 9B696ZZ BALL BEARING 1 34 98614S534-3 3/8" RATCHET ANVIL 1
13 98614S512 REAR END PLATE 1 35 9861435L SPRING 1
14 9SP2520 SPRING PIN 1 36 9861436L SPRING CAP 1
15 98614S214 ROTOR 1 37 98614S237 RATCHET PAWL 1
16 98614S215 ROTOR BLADE 4 38 9861438 FRICTION SPRING 2
17 98614S216 CYLINDER 1 39 9961439 POST 2
18 9861417 FRONT END PLATE 1 40 98614S240-3 3/8" THRUST WASHER 1
19 9B608ZZ BALL BEARING 1 41 98614S241 RETAINING RING 1
20 9861419 WASHER 1 42 9389507-807 SILENCER (2x1x0.5) 2
21 9861420 INTERNAL GEAR 1 ** 98614S223A #23 GEAR PIVOT (3) & #24
1
CRANK SHAFT(1) ASSEMBLY
22 9861421 PLANET GEAR 3
Page 4
Loading...