Page 1
MODEL: 6560
4" 1.0 HP CUT-OFF TOOL
Page 2
Important Warnings - Grinders & Cut-Off Tools
SPECIFICATIONS
Free
Model No.
6560 14,000 1.0 4
Speed
(RPM)
Motor
(HP)
Wheel
Size (in)
Cutting
Capacity
3/8" x 11
Gears
Single Reduction
Exhaust
Rear 1.8 9.5 4.2 3/8 1/4
Weight
(lbs.)
Length
(in)
Air
Cons.
(CFM)
Rec. Hose
Size
(in.)
Air Inlet
(in.)
NPT/BSP
Air Supply
Tools of this class operate on a wide range of air pressure. It is recommended that air pressure of these tools measures 90 PSI at the tool while running free. Higher
pressure and unclean air will shorten the tool’s life because of faster wear and may create a hazardous condition and void the warranty. Water in the air line will
cause damage to the tool. Drain the air tank daily. Clean the air inlet lter screen on at least a weekly schedule. The recommended hookup procedure can be viewed
in the illustration below. The air inlet, used for connecting air supply, has standard 1/4” NPT and 1/4“ BSP thread.. Line pressure should be increased to compensate
for unusually long air hoses (over 25 feet). Minimum hose diameter should be 3/8” I.D. and ttings should have the same inside dimensions.
Page 3
MODEL: 6560
4" 1.0 HP CUT-OFF TOOL
Exploded View & Parts List
Ref #Part Number Description Qty Ref #Part Number Description Qty.
1 540F-030 Disc Nut 1 23 00-41121 O-Ring 2
2 540F-005 Cutting Wheel 1 24 218F-026 Bushing 1
3 540F-034 Washer 1 25 00-41133 O-Ring 1
4 530-002 Nut 1 26 00-41132 O-Ring 1
5 540F-004 Protecting Cover 1 27 218F-027 Valve Stem 1
6 540F-001 Shaft 1 28 218F-029 Spring 1
7 00-4135 O-Ring 1 29 551F-038 Regulator 1
8 511-005 Clamp Nut 1 30 00-4102 O-Ring 1
9 00-2314 Ball Bearing 1 31 00-41134 O-Ring 1
10 00-3325 Spring Pin 2 32 551F-030 Valve Plug 1
11 511-019 Front End Plate 1 33 218F-043 Throttle Lever 1
12 00-3328 Spring Pin 1 34 541F-038
13 511-006 Spacer 1 35 218F-039
14 541F-021 Rotor Blade 4 36 541F-038B
15 541F-020 Rotor 1 37 00-4159 O-Ring 1
16 541F-022 Cylinder 1 38 218F-042
17 218F-023 Rear End Plate 1 39 218F-050 Bushing 1
18 00-2323 Ball Bearing 1 40 218F-034A Air Inlet (1/4” BSP) 1
19 00-3505 Snap Ring 1 218F-034C Air Inlet (1/4” NPT)
20 218F-045-C Rear Gasket 1 41 511-007 Double Ended Wrench 1
216-037
21
22
541F-025 Motor Housing
Seal Lump
1
1
1
1
1 42 540F-007 Spanner 1
1
Page 4
Loading...