Page 1
MODEL: 6260
1.0 HP Composite
Straight Die Grinder
Page 2
Important Warnings - Die Grinders
1. Only use mounted grinding stones or mounted carbide burrs that meet ANSI standards, ISO standards or both.
2. Never adjust the die grinder, adjust the collets or change the mounted stones or mounted burrs unless the air supply and air hose is
disconnected from the die grinder.
3. Only personnel trained in the correct methods to adjust collets and change mounted stones and mounted burrs should conduct these
operations.
4. Always ensure that you are aware of the direction of the sparks being created by the grinding operation and ensure that the sparks are
not directed toward the operator or other persons in the area.
5.
6. Only use mounted stones or carbide burrs that have the correct spindle diameter that matches the original collet size provided by the die
grinder manufacturer.
7. Particular care must be taken not to use metric size mounted stones and mounted burrs with die grinders that have imperial size collets,
or use imperial mounted stones and mounted burrs with die grinders that have metric collets.
SPECIFICATIONS
Model No.
6260 22,000 1.0 1/4 Direct Drive Rear 1.2 9.25 8 3/8 1/4
Free Speed
(RPM)
Motor
(HP)
Collet Size
(in)
Gears Exhaust
Weight
(lbs.)
Length
(in)
Air Cons.
(CFM)
Rec.
Hose Size
(in.)
Air Inlet
(in.)
Air Supply
Tools of this class operate on a wide range of air pressure. It is recommended that air pressure of these tools measures 90 PSI at the tool while running free. Higher
pressure and unclean air will shorten the tool’s life because of faster wear and may create a hazardous condition and void the warranty. Water in the air line will
cause damage to the tool. Drain the air tank daily. Clean the air inlet lter screen on at least a weekly schedule. The recommended hookup procedure can be viewed
in the illustration below. The air inlet, used for connecting air supply, has standard 1/4” NPT American Thread or BSP British Standard Pipethread. Line pressure
should be increased to compensate for unusually long air hoses (over 25 feet). Minimum hose diameter should be 3/8 I.D. and ttings should have the same inside
dimensions.
Page 3
MODEL: 6260
1.0 HP Composite Die Grinder
Exploded View & Parts List
Ref #Part Number Description Qty Ref #Part Number Description Qty.
1 511-001 Collect Nut 1 21 00-41121 O-Ring 2
2 511-002B Collect 1 22 218F-026 Bushing 1
3 511-003 Spindle 1 23 00-41133 O-Ring 1
4 511-004 Housing Cover 1 24 00-41132 O-Ring 1
5 00-4135 O-Ring 2 25 218F-027 Valve Stem 1
6 511-005 Clamp Nut 1 26 218F-029 Spring 1
7 00-2314 Ball Bearing 1 27 551F-038 Regulator 1
8 00-3325 Spring Pin 2 28 00-4102 O-Ring 1
9 511-019 Front End Plate 1 29 00-41134 O-Ring 1
10 00-3328 Spring Pin 1 30 551F-030 Valve Plug 1
11 511-006 Spacer 1 31 218F-043 Throttle Lever 1
12 541F-021 Rotor Blade 4 32 541F-038
13 541F-020 Rotor 1 33 218F-039
14 541F-022 Cylinder 1 34 541F-038B
15 218F-023 Rear End Plate 1 35 00-4159 O-Ring 1
16 00-2323 Ball Bearing 1 36 218F-042
17 00-3505 Snap Ring 1 37 218F-050 Bushing 1
18 218F-045-C Rear Gasket 1 38 218F-034A Air Inlet (1/4” PF) UK 1
19 216-037 Seal Lump 1 218F-034C Air Inlet (1/4” NPT) USA
20 541F-025 Motor Housing 1 39 511-007 Double Ended Wrench 2
1
1
1
1
Page 4
Loading...