Airaid 883-311 Installation Instructions

Installation Instructions

For Part Number:

883-311 Snorkel kit for Airaid PN
883-306

Component Identification

1. Airbox Lid 1

2. Snorkel Tube 1

3. Snorkel Inlet 1

4. Snorkel Screen 1

5. Foam Prefilter 1

6. 3” Flexible Duct, 40” 1

7. 3” Loop Clamp 2

8. 1/4-20 x 1/2” Button Head Bolt 2

9. 1/4-20 Speed Nut 2

10. 1 3/4” Loop Clamp 3

11. 1/4-20x 1 1/4” Bolt 3

12. 1/4” Flat Washer 6

13. 1/4-20 Nylock Nut 3

14. 8-32 x 3/8 Button Head Bolt 4

15. Torx Screw 4

16. # 48 Hose Clamp 1

17. Edge Trim, 10” 1

18. Torx Bit #20 1

19. Bubble Sticker 1

Tools Required For Installation:

In addition to common hand tools, installation of this kit re­quires the use of a Jig Saw or equivalent. Low Profile Ratch­eting Screwdriver.

Full color instructions can be viewed on our web site at Airaid.com. Use the Product Search function to find your part number, and click View Details.

1. Disconnect the negative battery terminal. Install
the Airbox Lid (#1) onto the Airaid performance Airbox
using The four 1/4-20 x 1/2” Button Heads Bolts and
1/4” Flat Washers from the Airaid 883-306 intake.

2. Side the three small Loop Clamps (#10) onto the roll
cage A pillar as shown.

3. Mount the Snorkel Inlet(#3) to the Snorkel Tube (#2),
using the four Torx screws (#16), Torx Bit #18 and a
90deg. Low Profile Ratcheting Screwdriver.

4. Carefully insert the Airaid Foam Prefilter (#5) into the
Snorkel Inlet.

7. Close up of proper Snorkel hardware orientation.

5. Install the Snorkel Screen (#4) onto the Inlet using

the four 8-32 Button Head Screws(15).

8. Remove the Urethane Cap from the Airaid perfor­mance Airbox. The Clamp will be reused in step #10,
the cap will not be reused.

6. Attach the Snorkel Tube to the Loop Clamps using
three1/4-20 x 1 1/4 Bolts (#12), 1/4-20 Locknuts (#14),
and Flat washers (#13). Leave all hardware finger tight at
this time to allow for proper alignment

9. Install Cut out the fender Template and tape it in posi­tion on the corner of the passenger side hood as shown.

7. Using a jig saw or equivalent, follow the template and
cut out the Duct relief.

8. Install Slide the Speed Nuts (#11) onto the Cowl
plastic with the threaded side out.

9. Using a pair of dykes, pull out approximately three
windings of the steel wire inside of the Ducting (#6)and
cut it off.

10. Install the Flexible Duct onto the Airaid perfor­mance airbox as shown. Re use the Clamp from step
# 5.

13. Mount the duct to the Speed Nuts on the bulkhead
using the two 3” Loop Clamps and 1/4-20 x 1/2’ button
Head Bolts (#8).

11. Install the other end of the Ducting onto the Snorkel
tube using the #48 Hose Clamp (#16).

14. Slide the Edge Trim (#17) over the cut out on the
Hood.

12. Full view of Duct routing.

15. Align the Snorkel and Ducting and verify the

opening and closing action of the hood is not adversely
effected. Tighten all of the Clamp bolts when done.

Thank you for purchasing the Airaid Intake System. Contact Airaid @ [phone]
8:00 AM - 5:00 PM MST weekdays for questions regarding fit or instructions that are not clear to
you. Your Airaid Intake System was carefully inspected and packaged. Check that no parts are
missing, or were damaged during shipping. If any parts are missing, contact Airaid. The air filter
element is protected from direct exposure to water and debris; care should be taken not to drive
through deep water. WATER INGESTION IS THE DRIVERS RESPONSIBILITY! The air fil­ter is reusable and should be cleaned periodically.

16. Double check all of your work and re connect the
battery.

For your Oiled media filter we

suggest using the AIRAID Filter

Tune-Up Kit!

P/N 790-551 Aerosol Spray
P/N 790-550 Squeeze Spray

Airaid Filter Co. 2688 E Rose Garden Ln. Phoenix AZ 85050 [phone] [e-mail] www.airaid.com

REV.1.28.14

1.000

CHECK SIZE OF SQUARE TO CONFIRM

CORRECT SCALE BEFORE CUTTING