Airaid 883-306 Installation Instructions

Installation Instructions

For Part Number:

883-306 Intake Kit

2014 Kawasaki Teryx
2012-14 Kawasaki Teryx 4
750cc

Component Identification

1. Airaid Premium Filter 1

2. Top Panel 1

3. Bottom Panel 1

4. Filter Tray 1

5. Hood Scoop 1

6. Foam Pre Filter 1

7. Mounting Bracket 2

8. Silicone Coupler 1

9. Urethane Cap 1

10. #48 Hose Clamp 3

11. Blind Grommet 1

12. 1/4-20 x 1/2” Button Head screw 4

13. 1/4” Flat Washer 4

14. 1/4-20 x 1/4” Button Head screw 4

15. #8-32 Thread Cutting Screw 10

16. Edge Trim, 36” 1

17. Bubble Sticker 1

Tools Required For Installation:

In addition to common hand tools, this installation requires

the use of a : Hand drill, 1/2” Drill Bit, Jig Saw, Center

punch, and hammer.

Full color instructions can be viewed on our web site at Airaid.com. Use the Product Search function to find your part number, and click View Details.

1. Raise the hood of the vehicle. Locate and disconnect
the negative battery terminal underneath the airbox. Re­move the four airbox bolts and set them aside. They will
be reused.

Bottom Panel

2. Loosen the clamps on the factory airbox couplers.

3. Remove the factory airbox and couplers from the vehi-

cle.

Top Panel

4. Create the Airbox Assembly by sliding the Top Panel

(#2) into the Bottom Panel (#3). Use four of the 8-32
Thread Cutting Screws (#15) on each side to secure the
panels.

5. Use the two remaining Thread Cutting Screws on the
bottom of the assembly shown.

6. Install the Mounting Brackets (#7) onto both sides of
the Airbox Assembly a shown using the four 1/4-20 x
1/4” Button Head Bolts (#14)

7. Slide the Airaid Premium Filter (#1) onto the mount­ing tube inside the Airbox Assembly. Note the location
of the isolator tab on the filter inside of the box.

8. Tighten the Air Filter clamp though the access port
on the back side of the Airbox.

9. Install the Blind Grommet (#11) into the access port.

10. Install the Silicone Coupler (#8) and Two #48 Hose

Clamps (#10) onto the factory intake tube. Leave the
Clamps loose for now.

11. Insert the Airbox outlet into the Silicone coupler and
tighten the Clamps. Mount the airbox to the vehicle by
reusing the factory hardware from step one.

STOP ! If you have purchased the Snorkel kit PN
883-311 do not proceed to step 12. Refer to 883-311
instructions to complete installation.

12. Cut out the Template and carefully position it onto

the vehicles hood. Tape the template in place.

13. Mark the hole locations in each corner using a center
punch.

16. Install the Edge Trim (#16) onto the hood, trim to fit.

14. Using a 1/8” bit , drill out the punched holes on the

hood. Finish the holes using a 1/2” bit or UniBit.

17. Install the Urethane Cap (#9) onto the Airbox Inlet
tube and secure it using the third #48 Clamp.

15. Using a jig saw, cut out the center section of the
hood.

18. Place the Filter Tray (#4) onto the Air Box as
shown.

19. Install the Hood Scoop onto the Airbox Assembly
using the four sets of 1/4-20 x 1/2’ Button Head Bolts
(#12) and 1/4” Flat Washers (#13). Leave the bolts loose
for now to allow for final adjustment.

20. Insert the Foam Pre Filter (#6) into the Hood Scoop.

21. Lower the hood down onto the vehicle and secure

it. Align the Hood Scoop from left to right inside of the
cut out . Raise the hood, secure the Bolts and re con­nect the battery.

Thank you for purchasing the Airaid Intake System. Contact Airaid @ [phone] 8:00 AM - 5:00 PM MST weekdays for questions
regarding fit or instructions that are not clear to you. Your Airaid Intake System was carefully inspected and packaged. Check that no parts are
missing, or were damaged during shipping. If any parts are missing, contact Airaid. The air filter element is protected from direct exposure to wa­ter and debris; care should be taken not to drive through deep water. WATER INGESTION IS THE DRIVERS RESPONSIBILITY! The air filter
is reusable and should be cleaned periodically.

For your Oiled media filter we suggest
using the AIRAID Filter Tune-Up Kit!

P/N 790-551 Aerosol Spray
P/N 790-550 Squeeze Spray

Airaid Filter Co. 2688 E Rose Garden Ln. Phoenix AZ 85050 [phone] [e-mail] www.airaid.com

REV.02.07.14

1.00

CORRECT SCALE BEFORE CUTTING

CHECK SIZE OF SQUARE TO CONFIRM

THEN CUT STRAIGHT LINES TO CONNECT HOLES

DRILL 1/2" HOLES FIRST

ALIGN EDGE WITH BODY LINE

ALIGN EDGE OF PAPER WITH TOP EDGE OF HOOD