Airaid 530-578-P Installation Instructions

# 530-578-P INSTALLATION INSTRUCTIONS

93-97 Honda Accord SOHC, DOHC, VTEC, Non-VTEC, 2.2L

Thank you for purchasing the PowerAid Throttle Body Spacer. Please read the
instruction manual carefully bef ore proceeding with the installation. Cont ac t AIRAID @
[phone] 8:00 AM - 5:00 PM MST Weekdays for questions regarding fit or in­structions that are not clear to you. Your PowerAid Throttle Body Spacer was carefully
inspected and packaged. Check that no parts are missing, or were damaged during
shipping. If any parts are missing, please contact AIRAID.

Thank you for selecting AIRAID.

Nitrous Fitting
Not Included

Please refer to a nitrous oxide system manufacturer for proper application for your vehicle.

Be sure to follow the manufacture’s instructions & warnings when using nitrous oxide.

Parts List

(1) Power Plate

(2) Gaskets

(4) 8mm x 65mm Bolts

(4) 8mm Lock Washers

(1) Linkage Plate

(2) 6mm Flat Head Screws

(1) 1/16” NPTx3/16” Vacuum Fitting

Vacuum Gauge
Fitting Shown

Tools List

12mm Deep Socket

4mm Allen Wrench

Flathead Screwdriver

Phillips Screwdriver

8mm Socket

Nut Driver

Vice Grips

(2) 1/16”NPT Plugs

(2) 6mm Flat Washers

1

Installation Instructions. Read Me!

1. DISCONNECT NEGATIVE (-) BATTERY CABLE.

2. Disconnect electrical connectors to throttle body & factory intake tube. See Fig#1

3. Using a 10mm socket, remove two bolts holding throttle cable bracket to intake manifold. Retain bolts fo r later use. See Fig#2

4. Remove throttle cable(s) from throttle body.

5. Using a Phillips screwdriver, loosen hose clamp on factory intake tube & remove tube from throttle body & air box. See Fig#3

6. Remove (4) 12mm nuts from the throttle body. Retain (2) 12mm nuts for later use.

7. Remove throttle body from intake manifold & set aside. Note: leave coolant lines conn ected to throttle body.

8. Using the two original 12mm nuts or vise grips, r emove the four (4) studs from intake manifold. See Fig#4

9. Clean gasket surface of throttle body & intake manifold.

10. Optional

utilized, install necessary fittings before installing spacer on vehicle. Other 1/16” NPT fittings may be installed such as power ad­ders. Refer to “PowerPort” section on reverse.

11. Install power plate by placing the part number facing the throttle body with one supplied gasket on both sides of the power plate.

(Note

12. Install the (4) supplied bolts and lock washers in throttle body, tighten evenly. DO NOT OVER TIGHTEN. Ref. B

13. Install throttle linkage extender using (2) flat head bolts provided. Note
intake manifold and throttle linkage extender to provide a flat surface for mounting. See Fig#2

14. Position throttle cable bracket over extender & install using (2) original bolts that were removed earlier. Install throttle cable(s) on
throttle body linkage. See Fig#2

15. Inspect & test throttle linkage for full open & closed travel before driving. Cables may require adjustment-Refer to service manual.

16. Reinstall air intake tube, all electrical connectors & negative battery cable.

: Included in the hardware pack is one 3/16” vacuum line fitting, this may be used for a va cuum gauge. If power ports are

: gaskets must be placed in correct orientation to line up with factory air passages.) Ref. A

: Some vehicles may require two 6mm washers between the

The sound of power...The “whistle” means its working!

- (1) Power Plate

Fig #1

Ref. A

(2) Gaskets

- (4) 8mm x 65mm Bolts

Ref. B

(4) 8mm Washers

Ref. C

- (1) Throttle Body

Fig #2 Fig #3 Fig #4

Rev.03/14/07

AIRAID Filter Co. 2688 E Rose Garden Ln. Phoenix AZ 85050 [phone] [e-mail] www.airaid.com

2