Airaid 510-734 Installation Instructions

INSTALLATION INSTRUCTIONS

#510-934 Modular Intake Tube

OR

#510-734 Airaid Jr. Kit

95-04 Toyota Tacoma & 95-02 Toyota 4Runner 3.4L

Thank you for purchasing the Airaid M odular Intake Tube or Airaid Jr. Kit. Please read the instruction
manual carefully before proceeding with the installation. Contact Airaid @ 800-498-6951 8:00 AM – 5:00 PM
MST weekdays for questions regarding fit or instructions that are not clear to you. Your Airaid Modular Intake
Tube or Airaid Jr. Kit was carefully inspected and packaged. Check that no parts are missing, or were damaged
during shipping. If any parts are missing, contact Airaid.

Thank you for selecting Airaid

Packing List:

KIT934T Modular Intake Tube 1

850-054 Airaid Premium Filter 1

KITHUMPHS06 Urethane Hump Hose 1

KITCOUPLER04 Urethane Coupler

KIT934HP Hardware & Instructions 1

KITHS48 #4

-

- KITHS52 #52 Hose Clamp 2
KITFITTING02 ¼” NPT, ¼” Barb Fitting 2

-

- KITFITTING03 ½” x 5/8” Connector 1

8 Hose Clamp 2

.

Packing List (cont’d):

- KITFITTING04 ¼” NPT Plug 1

- KITHOSE01 ½” x 4” Breather Hose 1

- KITHOSE03 ¼” x 16” Vacuum Hose 1

1

- KITSNP16M4 Black Speed Clamp 2

Tools Required for this Installation:

Flat Head & Phillips Screwdriver

½” wrench

¼” Allen wrench

Installation Instructions. Read Me!

m

I DISCONNECT NEGATIVE (-) BATTERY CABLE
II Remove Factory Intake Assembly

a) Using Phillips screwdriver, loosen the hose clamps on the factory intake

tube. See Fig#1

b) Remove vacuum line and hose from the intake tube. Discard original ¼”

vacuum line for longer vacuum line supplied with Airaid MIT. (Note

Factory hose near throttle body will be reconnected to AirAid intake tube
assembly.) See Fig#1

c) Disconnect Mass Air Sensor wire harness from intake tube. (Note

Air Sensor remains in original location.) See Fig#2

d) Remove factory intake tube assembly from vehicle. (Note

box assembly remains in original location.) See Fig#2

II

Assemble the Airaid Modular Intake Tube

a) Install supplied nylon barbed fitting in rear threaded hole (furthest from

larger diameter tube end) of Airaid intake tube. See Fig#3

b) Install supplied ¼” threaded plug into threaded hole (closest to larger

diameter tube end) of Airaid intake tube. See Fig#3

c) Early models, 1995-98 will use the second barbed fitting. See Fig#4
d) Place hump hose and two #52 hose clamps on larger end of intake tube

and place coupler with two #48 hose clamps on smaller end of tube. See
Fig#3 (Note

: Leave all hose clamps loose for final assembly.)

: factory air

III Airaid Modular Intake Tube Installation

a) Position the Airaid intake tube in place of the original factory assembly.
b) Connect the Airaid intake tube to the engine by sliding the coupler over

the end of the throttle body.

c) Connect the Airaid intake tube to the factory air box by sliding the hump

hose over the end of the air box.

d) Adjust the intake tube to insure proper alignment from the throttle body

and the factory air box. (Note
box to allow for engine movement.)

e) Tighten all four hose clamps on the Airaid intake tube.
f) Using supplied ¼” vacuum line; connect steel tube on intake manifold to

¼” barbed fitting on intake tube.

g) Using supplied 5/8” to ½” barbed fitting and hose, connect the factory

hose located by the throttle body to the intake tube. Use two supplied #16

speed clamps to secure line to barbed ends. See Fig#5

h) Re-connect the Mass Air Sensor to the factory tube.

: Leave a gap between the tube and the air

IV Airaid Jr. P/N 300-724 Replacement Filter

a) If you purchased the Airaid Jr. kit P/N 300-724, replace the factory

air filter with the Airaid Premium Filter included in the Airaid Jr. kit.

V Finishing Up

a) Tighten all hose clamps & inspect overall work.
b) Check hood clearance.
c) Ensure that no foreign objects are in the intake path!
d) Re-connect negative battery cable.

Rev Date 6/12/12

: Mass

Fig#1

:

Fig#2

Fig#3

Fig#4

Fig#5

Airaid Filter Co. 2688 E Rose Garden Ln. Phoenix AZ 85050 [phone] [e-mail] www.airaid.co